In the Linux kernel, the following vulnerability has been resolved: tracing: Fix race issue between cpu buffer write and swap Warning happened in rb_end_commit() at code: if (RB_WARN_ON(cpu_buffer, !local_read(&cpu_buffer->committing))) WARNING: CPU: 0 PID: 139 at kernel/trace/ring_buffer.c:3142 rb_commit+0x402/0x4a0 Call Trace: ring_buffer_unlock_commit+0x42/0x250 trace_buffer_unlock_commit_regs+0x3b/0x250 trace_event_buffer_commit+0xe5/0x440 trace_event_buffer_reserve+0x11c/0x150 trace_event_raw_event_sched_switch+0x23c/0x2c0 __traceiter_sched_switch+0x59/0x80 __schedule+0x72b/0x1580 schedule+0x92/0x120 worker_thread+0xa0/0x6f0 It is because the race between writing event into cpu buffer and swapping cpu buffer through file per_cpu/cpu0/snapshot: Write on CPU 0 Swap buffer by per_cpu/cpu0/snapshot on CPU 1 -------- -------- tracing_snapshot_write() [...] ring_buffer_lock_reserve() cpu_buffer = buffer->buffers[cpu]; // 1. Suppose find 'cpu_buffer_a'; [...] rb_reserve_next_event() [...] ring_buffer_swap_cpu() if (local_read(&cpu_buffer_a->committing)) goto out_dec; if (local_read(&cpu_buffer_b->committing)) goto out_dec; buffer_a->buffers[cpu] = cpu_buffer_b; buffer_b->buffers[cpu] = cpu_buffer_a; // 2. cpu_buffer has swapped here. rb_start_commit(cpu_buffer); if (unlikely(READ_ONCE(cpu_buffer->buffer) != buffer)) { // 3. This check passed due to 'cpu_buffer->buffer' [...] // has not changed here. return NULL; } cpu_buffer_b->buffer = buffer_a; cpu_buffer_a->buffer = buffer_b; [...] // 4. Reserve event from 'cpu_buffer_a'. ring_buffer_unlock_commit() [...] cpu_buffer = buffer->buffers[cpu]; // 5. Now find 'cpu_buffer_b' !!! rb_commit(cpu_buffer) rb_end_commit() // 6. WARN for the wrong 'committing' state !!! Based on above analysis, we can easily reproduce by following testcase: ``` bash #!/bin/bash dmesg -n 7 sysctl -w kernel.panic_on_warn=1 TR=/sys/kernel/tracing echo 7 > ${TR}/buffer_size_kb echo "sched:sched_switch" > ${TR}/set_event while [ true ]; do echo 1 > ${TR}/per_cpu/cpu0/snapshot done & while [ true ]; do echo 1 > ${TR}/per_cpu/cpu0/snapshot done & while [ true ]; do echo 1 > ${TR}/per_cpu/cpu0/snapshot done & ``` To fix it, IIUC, we can use smp_call_function_single() to do the swap on the target cpu where the buffer is located, so that above race would be avoided.

In the Linux kernel, the following vulnerability has been resolved: mm/ksm: fix race with VMA iteration and mm_struct teardown exit_mmap() will tear down the VMAs and maple tree with the mmap_lock held in write mode. Ensure that the maple tree is still valid by checking ksm_test_exit() after taking the mmap_lock in read mode, but before the for_each_vma() iterator dereferences a destroyed maple tree. Since the maple tree is destroyed, the flags telling lockdep to check an external lock has been cleared. Skip the for_each_vma() iterator to avoid dereferencing a maple tree without the external lock flag, which would create a lockdep warning.

In the Linux kernel, the following vulnerability has been resolved: power: supply: bq25890: Fix external_power_changed race bq25890_charger_external_power_changed() dereferences bq->charger, which gets sets in bq25890_power_supply_init() like this: bq->charger = devm_power_supply_register(bq->dev, &bq->desc, &psy_cfg); As soon as devm_power_supply_register() has called device_add() the external_power_changed callback can get called. So there is a window where bq25890_charger_external_power_changed() may get called while bq->charger has not been set yet leading to a NULL pointer dereference. This race hits during boot sometimes on a Lenovo Yoga Book 1 yb1-x90f when the cht_wcove_pwrsrc (extcon) power_supply is done with detecting the connected charger-type which happens to exactly hit the small window: BUG: kernel NULL pointer dereference, address: 0000000000000018 <snip> RIP: 0010:__power_supply_is_supplied_by+0xb/0xb0 <snip> Call Trace: <TASK> __power_supply_get_supplier_property+0x19/0x50 class_for_each_device+0xb1/0xe0 power_supply_get_property_from_supplier+0x2e/0x50 bq25890_charger_external_power_changed+0x38/0x1b0 [bq25890_charger] __power_supply_changed_work+0x30/0x40 class_for_each_device+0xb1/0xe0 power_supply_changed_work+0x5f/0xe0 <snip> Fixing this is easy. The external_power_changed callback gets passed the power_supply which will eventually get stored in bq->charger, so bq25890_charger_external_power_changed() can simply directly use the passed in psy argument which is always valid.

In the Linux kernel, the following vulnerability has been resolved: power: supply: axp288_fuel_gauge: Fix external_power_changed race fuel_gauge_external_power_changed() dereferences info->bat, which gets sets in axp288_fuel_gauge_probe() like this: info->bat = devm_power_supply_register(dev, &fuel_gauge_desc, &psy_cfg); As soon as devm_power_supply_register() has called device_add() the external_power_changed callback can get called. So there is a window where fuel_gauge_external_power_changed() may get called while info->bat has not been set yet leading to a NULL pointer dereference. Fixing this is easy. The external_power_changed callback gets passed the power_supply which will eventually get stored in info->bat, so fuel_gauge_external_power_changed() can simply directly use the passed in psy argument which is always valid.

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Fix deletion race condition System crash when using debug kernel due to link list corruption. The cause of the link list corruption is due to session deletion was allowed to queue up twice. Here's the internal trace that show the same port was allowed to double queue for deletion on different cpu. 20808683956 015 qla2xxx [0000:13:00.1]-e801:4: Scheduling sess ffff93ebf9306800 for deletion 50:06:0e:80:12:48:ff:50 fc4_type 1 20808683957 027 qla2xxx [0000:13:00.1]-e801:4: Scheduling sess ffff93ebf9306800 for deletion 50:06:0e:80:12:48:ff:50 fc4_type 1 Move the clearing/setting of deleted flag lock.

In the Linux kernel, the following vulnerability has been resolved: f2fs: don't reset unchangable mount option in f2fs_remount() syzbot reports a bug as below: general protection fault, probably for non-canonical address 0xdffffc0000000009: 0000 [#1] PREEMPT SMP KASAN RIP: 0010:__lock_acquire+0x69/0x2000 kernel/locking/lockdep.c:4942 Call Trace: lock_acquire+0x1e3/0x520 kernel/locking/lockdep.c:5691 __raw_write_lock include/linux/rwlock_api_smp.h:209 [inline] _raw_write_lock+0x2e/0x40 kernel/locking/spinlock.c:300 __drop_extent_tree+0x3ac/0x660 fs/f2fs/extent_cache.c:1100 f2fs_drop_extent_tree+0x17/0x30 fs/f2fs/extent_cache.c:1116 f2fs_insert_range+0x2d5/0x3c0 fs/f2fs/file.c:1664 f2fs_fallocate+0x4e4/0x6d0 fs/f2fs/file.c:1838 vfs_fallocate+0x54b/0x6b0 fs/open.c:324 ksys_fallocate fs/open.c:347 [inline] __do_sys_fallocate fs/open.c:355 [inline] __se_sys_fallocate fs/open.c:353 [inline] __x64_sys_fallocate+0xbd/0x100 fs/open.c:353 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd The root cause is race condition as below: - since it tries to remount rw filesystem, so that do_remount won't call sb_prepare_remount_readonly to block fallocate, there may be race condition in between remount and fallocate. - in f2fs_remount(), default_options() will reset mount option to default one, and then update it based on result of parse_options(), so there is a hole which race condition can happen. Thread A Thread B - f2fs_fill_super - parse_options - clear_opt(READ_EXTENT_CACHE) - f2fs_remount - default_options - set_opt(READ_EXTENT_CACHE) - f2fs_fallocate - f2fs_insert_range - f2fs_drop_extent_tree - __drop_extent_tree - __may_extent_tree - test_opt(READ_EXTENT_CACHE) return true - write_lock(&et->lock) access NULL pointer - parse_options - clear_opt(READ_EXTENT_CACHE)

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix hci_suspend_sync crash If hci_unregister_dev() frees the hci_dev object but hci_suspend_notifier may still be accessing it, it can cause the program to crash. Here's the call trace: <4>[102152.653246] Call Trace: <4>[102152.653254] hci_suspend_sync+0x109/0x301 [bluetooth] <4>[102152.653259] hci_suspend_dev+0x78/0xcd [bluetooth] <4>[102152.653263] hci_suspend_notifier+0x42/0x7a [bluetooth] <4>[102152.653268] notifier_call_chain+0x43/0x6b <4>[102152.653271] __blocking_notifier_call_chain+0x48/0x69 <4>[102152.653273] __pm_notifier_call_chain+0x22/0x39 <4>[102152.653276] pm_suspend+0x287/0x57c <4>[102152.653278] state_store+0xae/0xe5 <4>[102152.653281] kernfs_fop_write+0x109/0x173 <4>[102152.653284] __vfs_write+0x16f/0x1a2 <4>[102152.653287] ? selinux_file_permission+0xca/0x16f <4>[102152.653289] ? security_file_permission+0x36/0x109 <4>[102152.653291] vfs_write+0x114/0x21d <4>[102152.653293] __x64_sys_write+0x7b/0xdb <4>[102152.653296] do_syscall_64+0x59/0x194 <4>[102152.653299] entry_SYSCALL_64_after_hwframe+0x5c/0xc1 This patch holds the reference count of the hci_dev object while processing it in hci_suspend_notifier to avoid potential crash caused by the race condition.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix disconnect vs accept race Despite commit 0ad529d9fd2b ("mptcp: fix possible divide by zero in recvmsg()"), the mptcp protocol is still prone to a race between disconnect() (or shutdown) and accept. The root cause is that the mentioned commit checks the msk-level flag, but mptcp_stream_accept() does acquire the msk-level lock, as it can rely directly on the first subflow lock. As reported by Christoph than can lead to a race where an msk socket is accepted after that mptcp_subflow_queue_clean() releases the listener socket lock and just before it takes destructive actions leading to the following splat: BUG: kernel NULL pointer dereference, address: 0000000000000012 PGD 5a4ca067 P4D 5a4ca067 PUD 37d4c067 PMD 0 Oops: 0000 [#1] PREEMPT SMP CPU: 2 PID: 10955 Comm: syz-executor.5 Not tainted 6.5.0-rc1-gdc7b257ee5dd #37 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014 RIP: 0010:mptcp_stream_accept+0x1ee/0x2f0 include/net/inet_sock.h:330 Code: 0a 09 00 48 8b 1b 4c 39 e3 74 07 e8 bc 7c 7f fe eb a1 e8 b5 7c 7f fe 4c 8b 6c 24 08 eb 05 e8 a9 7c 7f fe 49 8b 85 d8 09 00 00 <0f> b6 40 12 88 44 24 07 0f b6 6c 24 07 bf 07 00 00 00 89 ee e8 89 RSP: 0018:ffffc90000d07dc0 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffff888037e8d020 RCX: ffff88803b093300 RDX: 0000000000000000 RSI: ffffffff833822c5 RDI: ffffffff8333896a RBP: 0000607f82031520 R08: ffff88803b093300 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000003e83 R12: ffff888037e8d020 R13: ffff888037e8c680 R14: ffff888009af7900 R15: ffff888009af6880 FS: 00007fc26d708640(0000) GS:ffff88807dd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000012 CR3: 0000000066bc5001 CR4: 0000000000370ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> do_accept+0x1ae/0x260 net/socket.c:1872 __sys_accept4+0x9b/0x110 net/socket.c:1913 __do_sys_accept4 net/socket.c:1954 [inline] __se_sys_accept4 net/socket.c:1951 [inline] __x64_sys_accept4+0x20/0x30 net/socket.c:1951 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x47/0xa0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 Address the issue by temporary removing the pending request socket from the accept queue, so that racing accept() can't touch them. After depleting the msk - the ssk still exists, as plain TCP sockets, re-insert them into the accept queue, so that later inet_csk_listen_stop() will complete the tcp socket disposal.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw89: fix potential race condition between napi_init and napi_enable A race condition can happen if netdev is registered, but NAPI isn't initialized yet, and meanwhile user space starts the netdev that will enable NAPI. Then, it hits BUG_ON(): kernel BUG at net/core/dev.c:6423! invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 417 Comm: iwd Not tainted 6.2.7-slab-dirty #3 eb0f5a8a9d91 Hardware name: LENOVO 21DL/LNVNB161216, BIOS JPCN20WW(V1.06) 09/20/2022 RIP: 0010:napi_enable+0x3f/0x50 Code: 48 89 c2 48 83 e2 f6 f6 81 89 08 00 00 02 74 0d 48 83 ... RSP: 0018:ffffada1414f3548 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffffa01425802080 RCX: 0000000000000000 RDX: 00000000000002ff RSI: ffffada14e50c614 RDI: ffffa01425808dc0 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000100 R12: ffffa01425808f58 R13: 0000000000000000 R14: ffffa01423498940 R15: 0000000000000001 FS: 00007f5577c0a740(0000) GS:ffffa0169fc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f5577a19972 CR3: 0000000125a7a000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> rtw89_pci_ops_start+0x1c/0x70 [rtw89_pci 6cbc75429515c181cbc386478d5cfb32ffc5a0f8] rtw89_core_start+0xbe/0x160 [rtw89_core fe07ecb874820b6d778370d4acb6ef8a37847f22] rtw89_ops_start+0x26/0x40 [rtw89_core fe07ecb874820b6d778370d4acb6ef8a37847f22] drv_start+0x42/0x100 [mac80211 c07fa22af8c3cf3f7d7ab3884ca990784d72e2d2] ieee80211_do_open+0x311/0x7d0 [mac80211 c07fa22af8c3cf3f7d7ab3884ca990784d72e2d2] ieee80211_open+0x6a/0x90 [mac80211 c07fa22af8c3cf3f7d7ab3884ca990784d72e2d2] __dev_open+0xe0/0x180 __dev_change_flags+0x1da/0x250 dev_change_flags+0x26/0x70 do_setlink+0x37c/0x12c0 ? ep_poll_callback+0x246/0x290 ? __nla_validate_parse+0x61/0xd00 ? __wake_up_common_lock+0x8f/0xd0 To fix this, follow Jonas' suggestion to switch the order of these functions and move register netdev to be the last step of PCI probe. Also, correct the error handling of rtw89_core_register_hw().

In the Linux kernel, the following vulnerability has been resolved: skbuff: Fix a race between coalescing and releasing SKBs Commit 1effe8ca4e34 ("skbuff: fix coalescing for page_pool fragment recycling") allowed coalescing to proceed with non page pool page and page pool page when @from is cloned, i.e. to->pp_recycle --> false from->pp_recycle --> true skb_cloned(from) --> true However, it actually requires skb_cloned(@from) to hold true until coalescing finishes in this situation. If the other cloned SKB is released while the merging is in process, from_shinfo->nr_frags will be set to 0 toward the end of the function, causing the increment of frag page _refcount to be unexpectedly skipped resulting in inconsistent reference counts. Later when SKB(@to) is released, it frees the page directly even though the page pool page is still in use, leading to use-after-free or double-free errors. So it should be prohibited. The double-free error message below prompted us to investigate: BUG: Bad page state in process swapper/1 pfn:0e0d1 page:00000000c6548b28 refcount:-1 mapcount:0 mapping:0000000000000000 index:0x2 pfn:0xe0d1 flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff) raw: 000fffffc0000000 0000000000000000 ffffffff00000101 0000000000000000 raw: 0000000000000002 0000000000000000 ffffffffffffffff 0000000000000000 page dumped because: nonzero _refcount CPU: 1 PID: 0 Comm: swapper/1 Tainted: G E 6.2.0+ Call Trace: <IRQ> dump_stack_lvl+0x32/0x50 bad_page+0x69/0xf0 free_pcp_prepare+0x260/0x2f0 free_unref_page+0x20/0x1c0 skb_release_data+0x10b/0x1a0 napi_consume_skb+0x56/0x150 net_rx_action+0xf0/0x350 ? __napi_schedule+0x79/0x90 __do_softirq+0xc8/0x2b1 __irq_exit_rcu+0xb9/0xf0 common_interrupt+0x82/0xa0 </IRQ> <TASK> asm_common_interrupt+0x22/0x40 RIP: 0010:default_idle+0xb/0x20

In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: fix race on port output assume the following setup on a single machine: 1. An openvswitch instance with one bridge and default flows 2. two network namespaces "server" and "client" 3. two ovs interfaces "server" and "client" on the bridge 4. for each ovs interface a veth pair with a matching name and 32 rx and tx queues 5. move the ends of the veth pairs to the respective network namespaces 6. assign ip addresses to each of the veth ends in the namespaces (needs to be the same subnet) 7. start some http server on the server network namespace 8. test if a client in the client namespace can reach the http server when following the actions below the host has a chance of getting a cpu stuck in a infinite loop: 1. send a large amount of parallel requests to the http server (around 3000 curls should work) 2. in parallel delete the network namespace (do not delete interfaces or stop the server, just kill the namespace) there is a low chance that this will cause the below kernel cpu stuck message. If this does not happen just retry. Below there is also the output of bpftrace for the functions mentioned in the output. The series of events happening here is: 1. the network namespace is deleted calling `unregister_netdevice_many_notify` somewhere in the process 2. this sets first `NETREG_UNREGISTERING` on both ends of the veth and then runs `synchronize_net` 3. it then calls `call_netdevice_notifiers` with `NETDEV_UNREGISTER` 4. this is then handled by `dp_device_event` which calls `ovs_netdev_detach_dev` (if a vport is found, which is the case for the veth interface attached to ovs) 5. this removes the rx_handlers of the device but does not prevent packages to be sent to the device 6. `dp_device_event` then queues the vport deletion to work in background as a ovs_lock is needed that we do not hold in the unregistration path 7. `unregister_netdevice_many_notify` continues to call `netdev_unregister_kobject` which sets `real_num_tx_queues` to 0 8. port deletion continues (but details are not relevant for this issue) 9. at some future point the background task deletes the vport If after 7. but before 9. a packet is send to the ovs vport (which is not deleted at this point in time) which forwards it to the `dev_queue_xmit` flow even though the device is unregistering. In `skb_tx_hash` (which is called in the `dev_queue_xmit`) path there is a while loop (if the packet has a rx_queue recorded) that is infinite if `dev->real_num_tx_queues` is zero. To prevent this from happening we update `do_output` to handle devices without carrier the same as if the device is not found (which would be the code path after 9. is done). Additionally we now produce a warning in `skb_tx_hash` if we will hit the infinite loop. bpftrace (first word is function name): __dev_queue_xmit server: real_num_tx_queues: 1, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 1 netdev_core_pick_tx server: addr: 0xffff9f0a46d4a000 real_num_tx_queues: 1, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 1 dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 2, reg_state: 1 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 6, reg_state: 2 ovs_netdev_detach_dev server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, reg_state: 2 netdev_rx_handler_unregister server: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024, reg_state: 2 synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024 netdev_rx_handler_unregister ret server: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024, reg_state: 2 dp_ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix recv-recv race of completed call If a call receives an event (such as incoming data), the call gets placed on the socket's queue and a thread in recvmsg can be awakened to go and process it. Once the thread has picked up the call off of the queue, further events will cause it to be requeued, and once the socket lock is dropped (recvmsg uses call->user_mutex to allow the socket to be used in parallel), a second thread can come in and its recvmsg can pop the call off the socket queue again. In such a case, the first thread will be receiving stuff from the call and the second thread will be blocked on call->user_mutex. The first thread can, at this point, process both the event that it picked call for and the event that the second thread picked the call for and may see the call terminate - in which case the call will be "released", decoupling the call from the user call ID assigned to it (RXRPC_USER_CALL_ID in the control message). The first thread will return okay, but then the second thread will wake up holding the user_mutex and, if it sees that the call has been released by the first thread, it will BUG thusly: kernel BUG at net/rxrpc/recvmsg.c:474! Fix this by just dequeuing the call and ignoring it if it is seen to be already released. We can't tell userspace about it anyway as the user call ID has become stale.

In the Linux kernel, the following vulnerability has been resolved: l2tp: close all race conditions in l2tp_tunnel_register() The code in l2tp_tunnel_register() is racy in several ways: 1. It modifies the tunnel socket _after_ publishing it. 2. It calls setup_udp_tunnel_sock() on an existing socket without locking. 3. It changes sock lock class on fly, which triggers many syzbot reports. This patch amends all of them by moving socket initialization code before publishing and under sock lock. As suggested by Jakub, the l2tp lockdep class is not necessary as we can just switch to bh_lock_sock_nested().

In the Linux kernel, the following vulnerability has been resolved: KVM: s390: vsie: fix race during shadow creation Right now it is possible to see gmap->private being zero in kvm_s390_vsie_gmap_notifier resulting in a crash. This is due to the fact that we add gmap->private == kvm after creation: static int acquire_gmap_shadow(struct kvm_vcpu *vcpu, struct vsie_page *vsie_page) { [...] gmap = gmap_shadow(vcpu->arch.gmap, asce, edat); if (IS_ERR(gmap)) return PTR_ERR(gmap); gmap->private = vcpu->kvm; Let children inherit the private field of the parent.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix racing issue between ufshcd_mcq_abort() and ISR If command timeout happens and cq complete IRQ is raised at the same time, ufshcd_mcq_abort clears lprb->cmd and a NULL pointer deref happens in the ISR. Error log: ufshcd_abort: Device abort task at tag 18 Unable to handle kernel NULL pointer dereference at virtual address 0000000000000108 pc : [0xffffffe27ef867ac] scsi_dma_unmap+0xc/0x44 lr : [0xffffffe27f1b898c] ufshcd_release_scsi_cmd+0x24/0x114

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Check mailbox/SMT channel for consistency On reception of a completion interrupt the shared memory area is accessed to retrieve the message header at first and then, if the message sequence number identifies a transaction which is still pending, the related payload is fetched too. When an SCMI command times out the channel ownership remains with the platform until eventually a late reply is received and, as a consequence, any further transmission attempt remains pending, waiting for the channel to be relinquished by the platform. Once that late reply is received the channel ownership is given back to the agent and any pending request is then allowed to proceed and overwrite the SMT area of the just delivered late reply; then the wait for the reply to the new request starts. It has been observed that the spurious IRQ related to the late reply can be wrongly associated with the freshly enqueued request: when that happens the SCMI stack in-flight lookup procedure is fooled by the fact that the message header now present in the SMT area is related to the new pending transaction, even though the real reply has still to arrive. This race-condition on the A2P channel can be detected by looking at the channel status bits: a genuine reply from the platform will have set the channel free bit before triggering the completion IRQ. Add a consistency check to validate such condition in the A2P ISR.

In the Linux kernel, the following vulnerability has been resolved: pmdomain: mediatek: fix race conditions with genpd If the power domains are registered first with genpd and *after that* the driver attempts to power them on in the probe sequence, then it is possible that a race condition occurs if genpd tries to power them on in the same time. The same is valid for powering them off before unregistering them from genpd. Attempt to fix race conditions by first removing the domains from genpd and *after that* powering down domains. Also first power up the domains and *after that* register them to genpd.

In the Linux kernel, the following vulnerability has been resolved: tty: serial: fsl_lpuart: fix race on RX DMA shutdown From time to time DMA completion can come in the middle of DMA shutdown: <process ctx>: <IRQ>: lpuart32_shutdown() lpuart_dma_shutdown() del_timer_sync() lpuart_dma_rx_complete() lpuart_copy_rx_to_tty() mod_timer() lpuart_dma_rx_free() When the timer fires a bit later, sport->dma_rx_desc is NULL: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000004 pc : lpuart_copy_rx_to_tty+0xcc/0x5bc lr : lpuart_timer_func+0x1c/0x2c Call trace: lpuart_copy_rx_to_tty lpuart_timer_func call_timer_fn __run_timers.part.0 run_timer_softirq __do_softirq __irq_exit_rcu irq_exit handle_domain_irq gic_handle_irq call_on_irq_stack do_interrupt_handler ... To fix this fold del_timer_sync() into lpuart_dma_rx_free() after dmaengine_terminate_sync() to make sure timer will not be re-started in lpuart_copy_rx_to_tty() <= lpuart_dma_rx_complete().

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix race condition in hci_cmd_sync_clear There is a potential race condition in hci_cmd_sync_work and hci_cmd_sync_clear, and could lead to use-after-free. For instance, hci_cmd_sync_work is added to the 'req_workqueue' after cancel_work_sync The entry of 'cmd_sync_work_list' may be freed in hci_cmd_sync_clear, and causing kernel panic when it is used in 'hci_cmd_sync_work'. Here's the call trace: dump_stack_lvl+0x49/0x63 print_report.cold+0x5e/0x5d3 ? hci_cmd_sync_work+0x282/0x320 kasan_report+0xaa/0x120 ? hci_cmd_sync_work+0x282/0x320 __asan_report_load8_noabort+0x14/0x20 hci_cmd_sync_work+0x282/0x320 process_one_work+0x77b/0x11c0 ? _raw_spin_lock_irq+0x8e/0xf0 worker_thread+0x544/0x1180 ? poll_idle+0x1e0/0x1e0 kthread+0x285/0x320 ? process_one_work+0x11c0/0x11c0 ? kthread_complete_and_exit+0x30/0x30 ret_from_fork+0x22/0x30 </TASK> Allocated by task 266: kasan_save_stack+0x26/0x50 __kasan_kmalloc+0xae/0xe0 kmem_cache_alloc_trace+0x191/0x350 hci_cmd_sync_queue+0x97/0x2b0 hci_update_passive_scan+0x176/0x1d0 le_conn_complete_evt+0x1b5/0x1a00 hci_le_conn_complete_evt+0x234/0x340 hci_le_meta_evt+0x231/0x4e0 hci_event_packet+0x4c5/0xf00 hci_rx_work+0x37d/0x880 process_one_work+0x77b/0x11c0 worker_thread+0x544/0x1180 kthread+0x285/0x320 ret_from_fork+0x22/0x30 Freed by task 269: kasan_save_stack+0x26/0x50 kasan_set_track+0x25/0x40 kasan_set_free_info+0x24/0x40 ____kasan_slab_free+0x176/0x1c0 __kasan_slab_free+0x12/0x20 slab_free_freelist_hook+0x95/0x1a0 kfree+0xba/0x2f0 hci_cmd_sync_clear+0x14c/0x210 hci_unregister_dev+0xff/0x440 vhci_release+0x7b/0xf0 __fput+0x1f3/0x970 ____fput+0xe/0x20 task_work_run+0xd4/0x160 do_exit+0x8b0/0x22a0 do_group_exit+0xba/0x2a0 get_signal+0x1e4a/0x25b0 arch_do_signal_or_restart+0x93/0x1f80 exit_to_user_mode_prepare+0xf5/0x1a0 syscall_exit_to_user_mode+0x26/0x50 ret_from_fork+0x15/0x30

In the Linux kernel, the following vulnerability has been resolved: media: rkisp1: Fix IRQ disable race issue In rkisp1_isp_stop() and rkisp1_csi_disable() the driver masks the interrupts and then apparently assumes that the interrupt handler won't be running, and proceeds in the stop procedure. This is not the case, as the interrupt handler can already be running, which would lead to the ISP being disabled while the interrupt handler handling a captured frame. This brings up two issues: 1) the ISP could be powered off while the interrupt handler is still running and accessing registers, leading to board lockup, and 2) the interrupt handler code and the code that disables the streaming might do things that conflict. It is not clear to me if 2) causes a real issue, but 1) can be seen with a suitable delay (or printk in my case) in the interrupt handler, leading to board lockup.

In the Linux kernel, the following vulnerability has been resolved: powerpc/64s/interrupt: Fix interrupt exit race with security mitigation switch The RFI and STF security mitigation options can flip the interrupt_exit_not_reentrant static branch condition concurrently with the interrupt exit code which tests that branch. Interrupt exit tests this condition to set MSR[EE|RI] for exit, then again in the case a soft-masked interrupt is found pending, to recover the MSR so the interrupt can be replayed before attempting to exit again. If the condition changes between these two tests, the MSR and irq soft-mask state will become corrupted, leading to warnings and possible crashes. For example, if the branch is initially true then false, MSR[EE] will be 0 but PACA_IRQ_HARD_DIS clear and EE may not get enabled, leading to warnings in irq_64.c.

In the Linux kernel, the following vulnerability has been resolved: tee: amdtee: fix race condition in amdtee_open_session There is a potential race condition in amdtee_open_session that may lead to use-after-free. For instance, in amdtee_open_session() after sess->sess_mask is set, and before setting: sess->session_info[i] = session_info; if amdtee_close_session() closes this same session, then 'sess' data structure will be released, causing kernel panic when 'sess' is accessed within amdtee_open_session(). The solution is to set the bit sess->sess_mask as the last step in amdtee_open_session().

In the Linux kernel, the following vulnerability has been resolved: spi: Fix null dereference on suspend A race condition exists where a synchronous (noqueue) transfer can be active during a system suspend. This can cause a null pointer dereference exception to occur when the system resumes. Example order of events leading to the exception: 1. spi_sync() calls __spi_transfer_message_noqueue() which sets ctlr->cur_msg 2. Spi transfer begins via spi_transfer_one_message() 3. System is suspended interrupting the transfer context 4. System is resumed 6. spi_controller_resume() calls spi_start_queue() which resets cur_msg to NULL 7. Spi transfer context resumes and spi_finalize_current_message() is called which dereferences cur_msg (which is now NULL) Wait for synchronous transfers to complete before suspending by acquiring the bus mutex and setting/checking a suspend flag.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: Fix race condition in RPC handle list access The 'sess->rpc_handle_list' XArray manages RPC handles within a ksmbd session. Access to this list is intended to be protected by 'sess->rpc_lock' (an rw_semaphore). However, the locking implementation was flawed, leading to potential race conditions. In ksmbd_session_rpc_open(), the code incorrectly acquired only a read lock before calling xa_store() and xa_erase(). Since these operations modify the XArray structure, a write lock is required to ensure exclusive access and prevent data corruption from concurrent modifications. Furthermore, ksmbd_session_rpc_method() accessed the list using xa_load() without holding any lock at all. This could lead to reading inconsistent data or a potential use-after-free if an entry is concurrently removed and the pointer is dereferenced. Fix these issues by: 1. Using down_write() and up_write() in ksmbd_session_rpc_open() to ensure exclusive access during XArray modification, and ensuring the lock is correctly released on error paths. 2. Adding down_read() and up_read() in ksmbd_session_rpc_method() to safely protect the lookup.

In the Linux kernel, the following vulnerability has been resolved: ceph: fix race condition validating r_parent before applying state Add validation to ensure the cached parent directory inode matches the directory info in MDS replies. This prevents client-side race conditions where concurrent operations (e.g. rename) cause r_parent to become stale between request initiation and reply processing, which could lead to applying state changes to incorrect directory inodes. [ idryomov: folded a kerneldoc fixup and a follow-up fix from Alex to move CEPH_CAP_PIN reference when r_parent is updated: When the parent directory lock is not held, req->r_parent can become stale and is updated to point to the correct inode. However, the associated CEPH_CAP_PIN reference was not being adjusted. The CEPH_CAP_PIN is a reference on an inode that is tracked for accounting purposes. Moving this pin is important to keep the accounting balanced. When the pin was not moved from the old parent to the new one, it created two problems: The reference on the old, stale parent was never released, causing a reference leak. A reference for the new parent was never acquired, creating the risk of a reference underflow later in ceph_mdsc_release_request(). This patch corrects the logic by releasing the pin from the old parent and acquiring it for the new parent when r_parent is switched. This ensures reference accounting stays balanced. ]

In the Linux kernel, the following vulnerability has been resolved: net/packet: fix a race in packet_set_ring() and packet_notifier() When packet_set_ring() releases po->bind_lock, another thread can run packet_notifier() and process an NETDEV_UP event. This race and the fix are both similar to that of commit 15fe076edea7 ("net/packet: fix a race in packet_bind() and packet_notifier()"). There too the packet_notifier NETDEV_UP event managed to run while a po->bind_lock critical section had to be temporarily released. And the fix was similarly to temporarily set po->num to zero to keep the socket unhooked until the lock is retaken. The po->bind_lock in packet_set_ring and packet_notifier precede the introduction of git history.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix race between DIM disable and net_dim() There's a race between disabling DIM and NAPI callbacks using the dim pointer on the RQ or SQ. If NAPI checks the DIM state bit and sees it still set, it assumes `rq->dim` or `sq->dim` is valid. But if DIM gets disabled right after that check, the pointer might already be set to NULL, leading to a NULL pointer dereference in net_dim(). Fix this by calling `synchronize_net()` before freeing the DIM context. This ensures all in-progress NAPI callbacks are finished before the pointer is cleared. Kernel log: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... RIP: 0010:net_dim+0x23/0x190 ... Call Trace: <TASK> ? __die+0x20/0x60 ? page_fault_oops+0x150/0x3e0 ? common_interrupt+0xf/0xa0 ? sysvec_call_function_single+0xb/0x90 ? exc_page_fault+0x74/0x130 ? asm_exc_page_fault+0x22/0x30 ? net_dim+0x23/0x190 ? mlx5e_poll_ico_cq+0x41/0x6f0 [mlx5_core] ? sysvec_apic_timer_interrupt+0xb/0x90 mlx5e_handle_rx_dim+0x92/0xd0 [mlx5_core] mlx5e_napi_poll+0x2cd/0xac0 [mlx5_core] ? mlx5e_poll_ico_cq+0xe5/0x6f0 [mlx5_core] busy_poll_stop+0xa2/0x200 ? mlx5e_napi_poll+0x1d9/0xac0 [mlx5_core] ? mlx5e_trigger_irq+0x130/0x130 [mlx5_core] __napi_busy_loop+0x345/0x3b0 ? sysvec_call_function_single+0xb/0x90 ? asm_sysvec_call_function_single+0x16/0x20 ? sysvec_apic_timer_interrupt+0xb/0x90 ? pcpu_free_area+0x1e4/0x2e0 napi_busy_loop+0x11/0x20 xsk_recvmsg+0x10c/0x130 sock_recvmsg+0x44/0x70 __sys_recvfrom+0xbc/0x130 ? __schedule+0x398/0x890 __x64_sys_recvfrom+0x20/0x30 do_syscall_64+0x4c/0x100 entry_SYSCALL_64_after_hwframe+0x4b/0x53 ... ---[ end trace 0000000000000000 ]--- ... ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]---

An issue was discovered in the Linux kernel through 5.19.8. drivers/firmware/efi/capsule-loader.c has a race condition with a resultant use-after-free.

A flaw was found in pfn_swap_entry_to_page in memory management subsystem in the Linux Kernel. In this flaw, an attacker with a local user privilege may cause a denial of service problem due to a BUG statement referencing pmd_t x.

In audio driver, there is a use after free due to a race condition. This could lead to local denial of service in kernel.

In the Linux kernel, the following vulnerability has been resolved: f2fs: compress: fix race condition of overwrite vs truncate pos_fsstress testcase complains a panic as belew: ------------[ cut here ]------------ kernel BUG at fs/f2fs/compress.c:1082! invalid opcode: 0000 [#1] SMP PTI CPU: 4 PID: 2753477 Comm: kworker/u16:2 Tainted: G OE 5.12.0-rc1-custom #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014 Workqueue: writeback wb_workfn (flush-252:16) RIP: 0010:prepare_compress_overwrite+0x4c0/0x760 [f2fs] Call Trace: f2fs_prepare_compress_overwrite+0x5f/0x80 [f2fs] f2fs_write_cache_pages+0x468/0x8a0 [f2fs] f2fs_write_data_pages+0x2a4/0x2f0 [f2fs] do_writepages+0x38/0xc0 __writeback_single_inode+0x44/0x2a0 writeback_sb_inodes+0x223/0x4d0 __writeback_inodes_wb+0x56/0xf0 wb_writeback+0x1dd/0x290 wb_workfn+0x309/0x500 process_one_work+0x220/0x3c0 worker_thread+0x53/0x420 kthread+0x12f/0x150 ret_from_fork+0x22/0x30 The root cause is truncate() may race with overwrite as below, so that one reference count left in page can not guarantee the page attaching in mapping tree all the time, after truncation, later find_lock_page() may return NULL pointer. - prepare_compress_overwrite - f2fs_pagecache_get_page - unlock_page - f2fs_setattr - truncate_setsize - truncate_inode_page - delete_from_page_cache - find_lock_page Fix this by avoiding referencing updated page.

In the Linux kernel, the following vulnerability has been resolved: io-wq: check for wq exit after adding new worker task_work We check IO_WQ_BIT_EXIT before attempting to create a new worker, and wq exit cancels pending work if we have any. But it's possible to have a race between the two, where creation checks exit finding it not set, but we're in the process of exiting. The exit side will cancel pending creation task_work, but there's a gap where we add task_work after we've canceled existing creations at exit time. Fix this by checking the EXIT bit post adding the creation task_work. If it's set, run the same cancelation that exit does.

In the Linux kernel, the following vulnerability has been resolved: udp: fix race between close() and udp_abort() Kaustubh reported and diagnosed a panic in udp_lib_lookup(). The root cause is udp_abort() racing with close(). Both racing functions acquire the socket lock, but udp{v6}_destroy_sock() release it before performing destructive actions. We can't easily extend the socket lock scope to avoid the race, instead use the SOCK_DEAD flag to prevent udp_abort from doing any action when the critical race happens. Diagnosed-and-tested-by: Kaustubh Pandey <kapandey@codeaurora.org>

In the Linux kernel, the following vulnerability has been resolved: nfsd: Fix nsfd startup race (again) Commit bd5ae9288d64 ("nfsd: register pernet ops last, unregister first") has re-opened rpc_pipefs_event() race against nfsd_net_id registration (register_pernet_subsys()) which has been fixed by commit bb7ffbf29e76 ("nfsd: fix nsfd startup race triggering BUG_ON"). Restore the order of register_pernet_subsys() vs register_cld_notifier(). Add WARN_ON() to prevent a future regression. Crash info: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000012 CPU: 8 PID: 345 Comm: mount Not tainted 5.4.144-... #1 pc : rpc_pipefs_event+0x54/0x120 [nfsd] lr : rpc_pipefs_event+0x48/0x120 [nfsd] Call trace: rpc_pipefs_event+0x54/0x120 [nfsd] blocking_notifier_call_chain rpc_fill_super get_tree_keyed rpc_fs_get_tree vfs_get_tree do_mount ksys_mount __arm64_sys_mount el0_svc_handler el0_svc

In the Linux kernel, the following vulnerability has been resolved: userfaultfd: fix a race between writeprotect and exit_mmap() A race is possible when a process exits, its VMAs are removed by exit_mmap() and at the same time userfaultfd_writeprotect() is called. The race was detected by KASAN on a development kernel, but it appears to be possible on vanilla kernels as well. Use mmget_not_zero() to prevent the race as done in other userfaultfd operations.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix race in read_extent_buffer_pages() There are reports from tree-checker that detects corrupted nodes, without any obvious pattern so possibly an overwrite in memory. After some debugging it turns out there's a race when reading an extent buffer the uptodate status can be missed. To prevent concurrent reads for the same extent buffer, read_extent_buffer_pages() performs these checks: /* (1) */ if (test_bit(EXTENT_BUFFER_UPTODATE, &eb->bflags)) return 0; /* (2) */ if (test_and_set_bit(EXTENT_BUFFER_READING, &eb->bflags)) goto done; At this point, it seems safe to start the actual read operation. Once that completes, end_bbio_meta_read() does /* (3) */ set_extent_buffer_uptodate(eb); /* (4) */ clear_bit(EXTENT_BUFFER_READING, &eb->bflags); Normally, this is enough to ensure only one read happens, and all other callers wait for it to finish before returning. Unfortunately, there is a racey interleaving: Thread A | Thread B | Thread C ---------+----------+--------- (1) | | | (1) | (2) | | (3) | | (4) | | | (2) | | | (1) When this happens, thread B kicks of an unnecessary read. Worse, thread C will see UPTODATE set and return immediately, while the read from thread B is still in progress. This race could result in tree-checker errors like this as the extent buffer is concurrently modified: BTRFS critical (device dm-0): corrupted node, root=256 block=8550954455682405139 owner mismatch, have 11858205567642294356 expect [256, 18446744073709551360] Fix it by testing UPTODATE again after setting the READING bit, and if it's been set, skip the unnecessary read. [ minor update of changelog ]

An issue was discovered in include/asm-generic/tlb.h in the Linux kernel before 5.19. Because of a race condition (unmap_mapping_range versus munmap), a device driver can free a page while it still has stale TLB entries. This only occurs in situations with VM_PFNMAP VMAs.

There is a race condition vulnerability in the binder driver subsystem in the kernel.Successful exploitation of this vulnerability may affect kernel stability.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix crash on racing fsync and size-extending write into prealloc We have been seeing crashes on duplicate keys in btrfs_set_item_key_safe(): BTRFS critical (device vdb): slot 4 key (450 108 8192) new key (450 108 8192) ------------[ cut here ]------------ kernel BUG at fs/btrfs/ctree.c:2620! invalid opcode: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 3139 Comm: xfs_io Kdump: loaded Not tainted 6.9.0 #6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:btrfs_set_item_key_safe+0x11f/0x290 [btrfs] With the following stack trace: #0 btrfs_set_item_key_safe (fs/btrfs/ctree.c:2620:4) #1 btrfs_drop_extents (fs/btrfs/file.c:411:4) #2 log_one_extent (fs/btrfs/tree-log.c:4732:9) #3 btrfs_log_changed_extents (fs/btrfs/tree-log.c:4955:9) #4 btrfs_log_inode (fs/btrfs/tree-log.c:6626:9) #5 btrfs_log_inode_parent (fs/btrfs/tree-log.c:7070:8) #6 btrfs_log_dentry_safe (fs/btrfs/tree-log.c:7171:8) #7 btrfs_sync_file (fs/btrfs/file.c:1933:8) #8 vfs_fsync_range (fs/sync.c:188:9) #9 vfs_fsync (fs/sync.c:202:9) #10 do_fsync (fs/sync.c:212:9) #11 __do_sys_fdatasync (fs/sync.c:225:9) #12 __se_sys_fdatasync (fs/sync.c:223:1) #13 __x64_sys_fdatasync (fs/sync.c:223:1) #14 do_syscall_x64 (arch/x86/entry/common.c:52:14) #15 do_syscall_64 (arch/x86/entry/common.c:83:7) #16 entry_SYSCALL_64+0xaf/0x14c (arch/x86/entry/entry_64.S:121) So we're logging a changed extent from fsync, which is splitting an extent in the log tree. But this split part already exists in the tree, triggering the BUG(). This is the state of the log tree at the time of the crash, dumped with drgn (https://github.com/osandov/drgn/blob/main/contrib/btrfs_tree.py) to get more details than btrfs_print_leaf() gives us: >>> print_extent_buffer(prog.crashed_thread().stack_trace()[0]["eb"]) leaf 33439744 level 0 items 72 generation 9 owner 18446744073709551610 leaf 33439744 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da item 0 key (450 INODE_ITEM 0) itemoff 16123 itemsize 160 generation 7 transid 9 size 8192 nbytes 8473563889606862198 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 204 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417704.983333333 (2024-05-22 15:41:44) mtime 1716417704.983333333 (2024-05-22 15:41:44) otime 17592186044416.000000000 (559444-03-08 01:40:16) item 1 key (450 INODE_REF 256) itemoff 16110 itemsize 13 index 195 namelen 3 name: 193 item 2 key (450 XATTR_ITEM 1640047104) itemoff 16073 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 3 key (450 EXTENT_DATA 0) itemoff 16020 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 4096 ram 12288 extent compression 0 (none) item 4 key (450 EXTENT_DATA 4096) itemoff 15967 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 4096 nr 8192 item 5 key (450 EXTENT_DATA 8192) itemoff 15914 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 ... So the real problem happened earlier: notice that items 4 (4k-12k) and 5 (8k-12k) overlap. Both are prealloc extents. Item 4 straddles i_size and item 5 starts at i_size. Here is the state of ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ipv4: Fix uninit-value access in __ip_make_skb() KMSAN reported uninit-value access in __ip_make_skb() [1]. __ip_make_skb() tests HDRINCL to know if the skb has icmphdr. However, HDRINCL can cause a race condition. If calling setsockopt(2) with IP_HDRINCL changes HDRINCL while __ip_make_skb() is running, the function will access icmphdr in the skb even if it is not included. This causes the issue reported by KMSAN. Check FLOWI_FLAG_KNOWN_NH on fl4->flowi4_flags instead of testing HDRINCL on the socket. Also, fl4->fl4_icmp_type and fl4->fl4_icmp_code are not initialized. These are union in struct flowi4 and are implicitly initialized by flowi4_init_output(), but we should not rely on specific union layout. Initialize these explicitly in raw_sendmsg(). [1] BUG: KMSAN: uninit-value in __ip_make_skb+0x2b74/0x2d20 net/ipv4/ip_output.c:1481 __ip_make_skb+0x2b74/0x2d20 net/ipv4/ip_output.c:1481 ip_finish_skb include/net/ip.h:243 [inline] ip_push_pending_frames+0x4c/0x5c0 net/ipv4/ip_output.c:1508 raw_sendmsg+0x2381/0x2690 net/ipv4/raw.c:654 inet_sendmsg+0x27b/0x2a0 net/ipv4/af_inet.c:851 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x274/0x3c0 net/socket.c:745 __sys_sendto+0x62c/0x7b0 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x130/0x200 net/socket.c:2199 do_syscall_64+0xd8/0x1f0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x6d/0x75 Uninit was created at: slab_post_alloc_hook mm/slub.c:3804 [inline] slab_alloc_node mm/slub.c:3845 [inline] kmem_cache_alloc_node+0x5f6/0xc50 mm/slub.c:3888 kmalloc_reserve+0x13c/0x4a0 net/core/skbuff.c:577 __alloc_skb+0x35a/0x7c0 net/core/skbuff.c:668 alloc_skb include/linux/skbuff.h:1318 [inline] __ip_append_data+0x49ab/0x68c0 net/ipv4/ip_output.c:1128 ip_append_data+0x1e7/0x260 net/ipv4/ip_output.c:1365 raw_sendmsg+0x22b1/0x2690 net/ipv4/raw.c:648 inet_sendmsg+0x27b/0x2a0 net/ipv4/af_inet.c:851 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x274/0x3c0 net/socket.c:745 __sys_sendto+0x62c/0x7b0 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x130/0x200 net/socket.c:2199 do_syscall_64+0xd8/0x1f0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x6d/0x75 CPU: 1 PID: 15709 Comm: syz-executor.7 Not tainted 6.8.0-11567-gb3603fcb79b1 #25 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-1.fc39 04/01/2014

Multi-thread race condition vulnerability in the camera framework module. Impact: Successful exploitation of this vulnerability may affect availability.

In the Linux kernel, the following vulnerability has been resolved: eeprom: at24: fix memory corruption race condition If the eeprom is not accessible, an nvmem device will be registered, the read will fail, and the device will be torn down. If another driver accesses the nvmem device after the teardown, it will reference invalid memory. Move the failure point before registering the nvmem device.

In the Linux kernel, the following vulnerability has been resolved: platform/chrome: cros_ec_uart: properly fix race condition The cros_ec_uart_probe() function calls devm_serdev_device_open() before it calls serdev_device_set_client_ops(). This can trigger a NULL pointer dereference: BUG: kernel NULL pointer dereference, address: 0000000000000000 ... Call Trace: <TASK> ... ? ttyport_receive_buf A simplified version of crashing code is as follows: static inline size_t serdev_controller_receive_buf(struct serdev_controller *ctrl, const u8 *data, size_t count) { struct serdev_device *serdev = ctrl->serdev; if (!serdev || !serdev->ops->receive_buf) // CRASH! return 0; return serdev->ops->receive_buf(serdev, data, count); } It assumes that if SERPORT_ACTIVE is set and serdev exists, serdev->ops will also exist. This conflicts with the existing cros_ec_uart_probe() logic, as it first calls devm_serdev_device_open() (which sets SERPORT_ACTIVE), and only later sets serdev->ops via serdev_device_set_client_ops(). Commit 01f95d42b8f4 ("platform/chrome: cros_ec_uart: fix race condition") attempted to fix a similar race condition, but while doing so, made the window of error for this race condition to happen much wider. Attempt to fix the race condition again, making sure we fully setup before calling devm_serdev_device_open().

In the Linux kernel, the following vulnerability has been resolved: media: ti: j721e-csi2rx: Fix races while restarting DMA After the frame is submitted to DMA, it may happen that the submitted list is not updated soon enough, and the DMA callback is triggered before that. This can lead to kernel crashes, so move everything in a single lock/unlock section to prevent such races.

In the Linux kernel, the following vulnerability has been resolved: io_uring/zcrx: fix user_ref race between scrub and refill paths The io_zcrx_put_niov_uref() function uses a non-atomic check-then-decrement pattern (atomic_read followed by separate atomic_dec) to manipulate user_refs. This is serialized against other callers by rq_lock, but io_zcrx_scrub() modifies the same counter with atomic_xchg() WITHOUT holding rq_lock. On SMP systems, the following race exists: CPU0 (refill, holds rq_lock) CPU1 (scrub, no rq_lock) put_niov_uref: atomic_read(uref) - 1 // window opens atomic_xchg(uref, 0) - 1 return_niov_freelist(niov) [PUSH #1] // window closes atomic_dec(uref) - wraps to -1 returns true return_niov(niov) return_niov_freelist(niov) [PUSH #2: DOUBLE-FREE] The same niov is pushed to the freelist twice, causing free_count to exceed nr_iovs. Subsequent freelist pushes then perform an out-of-bounds write (a u32 value) past the kvmalloc'd freelist array into the adjacent slab object. Fix this by replacing the non-atomic read-then-dec in io_zcrx_put_niov_uref() with an atomic_try_cmpxchg loop that atomically tests and decrements user_refs. This makes the operation safe against concurrent atomic_xchg from scrub without requiring scrub to acquire rq_lock. [pavel: removed a warning and a comment]

Race condition vulnerability in the thermal management module. Impact: Successful exploitation of this vulnerability may affect availability.

Race condition vulnerability in the power consumption statistics module. Impact: Successful exploitation of this vulnerability may affect availability.

UAF vulnerability in the screen management module. Impact: Successful exploitation of this vulnerability may affect availability.

In the Linux kernel, the following vulnerability has been resolved: s390/cio: fix race condition during online processing A race condition exists in ccw_device_set_online() that can cause the online process to fail, leaving the affected device in an inconsistent state. As a result, subsequent attempts to set that device online fail with return code ENODEV. The problem occurs when a path verification request arrives after a wait for final device state completed, but before the result state is evaluated. Fix this by ensuring that the CCW-device lock is held between determining final state and checking result state. Note that since: commit 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers") path verification requests are much more likely to occur during boot, resulting in an increased chance of this race condition occurring.

In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: fix performance regression in swap operation The patch "netfilter: ipset: fix race condition between swap/destroy and kernel side add/del/test", commit 28628fa9 fixes a race condition. But the synchronize_rcu() added to the swap function unnecessarily slows it down: it can safely be moved to destroy and use call_rcu() instead. Eric Dumazet pointed out that simply calling the destroy functions as rcu callback does not work: sets with timeout use garbage collectors which need cancelling at destroy which can wait. Therefore the destroy functions are split into two: cancelling garbage collectors safely at executing the command received by netlink and moving the remaining part only into the rcu callback.