In the Linux kernel, the following vulnerability has been resolved: net: lan743x: fix potential out-of-bounds write in lan743x_ptp_io_event_clock_get() Before calling lan743x_ptp_io_event_clock_get(), the 'channel' value is checked against the maximum value of PCI11X1X_PTP_IO_MAX_CHANNELS(8). This seems correct and aligns with the PTP interrupt status register (PTP_INT_STS) specifications. However, lan743x_ptp_io_event_clock_get() writes to ptp->extts[] with only LAN743X_PTP_N_EXTTS(4) elements, using channel as an index: lan743x_ptp_io_event_clock_get(..., u8 channel,...) { ... /* Update Local timestamp */ extts = &ptp->extts[channel]; extts->ts.tv_sec = sec; ... } To avoid an out-of-bounds write and utilize all the supported GPIO inputs, set LAN743X_PTP_N_EXTTS to 8. Detected using the static analysis tool - Svace.

In the Linux kernel, the following vulnerability has been resolved: gpio: virtuser: fix potential out-of-bound write If the caller wrote more characters, count is truncated to the max available space in "simple_write_to_buffer". Check that the input size does not exceed the buffer size. Write a zero termination afterwards.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Fix invalid entry fetch in ath12k_dp_mon_srng_process Currently, ath12k_dp_mon_srng_process uses ath12k_hal_srng_src_get_next_entry to fetch the next entry from the destination ring. This is incorrect because ath12k_hal_srng_src_get_next_entry is intended for source rings, not destination rings. This leads to invalid entry fetches, causing potential data corruption or crashes due to accessing incorrect memory locations. This happens because the source ring and destination ring have different handling mechanisms and using the wrong function results in incorrect pointer arithmetic and ring management. To fix this issue, replace the call to ath12k_hal_srng_src_get_next_entry with ath12k_hal_srng_dst_get_next_entry in ath12k_dp_mon_srng_process. This ensures that the correct function is used for fetching entries from the destination ring, preventing invalid memory accesses. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k_htc: Abort software beacon handling if disabled A malicious USB device can send a WMI_SWBA_EVENTID event from an ath9k_htc-managed device before beaconing has been enabled. This causes a device-by-zero error in the driver, leading to either a crash or an out of bounds read. Prevent this by aborting the handling in ath9k_htc_swba() if beacons are not enabled.

In the Linux kernel, the following vulnerability has been resolved: iommu/amd: Fix potential buffer overflow in parse_ivrs_acpihid There is a string parsing logic error which can lead to an overflow of hid or uid buffers. Comparing ACPIID_LEN against a total string length doesn't take into account the lengths of individual hid and uid buffers so the check is insufficient in some cases. For example if the length of hid string is 4 and the length of the uid string is 260, the length of str will be equal to ACPIID_LEN + 1 but uid string will overflow uid buffer which size is 256. The same applies to the hid string with length 13 and uid string with length 250. Check the length of hid and uid strings separately to prevent buffer overflow. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad4851: fix ad4858 chan pointer handling The pointer returned from ad4851_parse_channels_common() is incremented internally as each channel is populated. In ad4858_parse_channels(), the same pointer was further incremented while setting ext_scan_type fields for each channel. This resulted in indio_dev->channels being set to a pointer past the end of the allocated array, potentially causing memory corruption or undefined behavior. Fix this by iterating over the channels using an explicit index instead of incrementing the pointer. This preserves the original base pointer and ensures all channel metadata is set correctly.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Fix invalid data access in ath12k_dp_rx_h_undecap_nwifi In certain cases, hardware might provide packets with a length greater than the maximum native Wi-Fi header length. This can lead to accessing and modifying fields in the header within the ath12k_dp_rx_h_undecap_nwifi function for DP_RX_DECAP_TYPE_NATIVE_WIFI decap type and potentially resulting in invalid data access and memory corruption. Add a sanity check before processing the SKB to prevent invalid data access in the undecap native Wi-Fi function for the DP_RX_DECAP_TYPE_NATIVE_WIFI decap type. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix max_sge overflow in smb_extract_folioq_to_rdma() This fixes the following problem: [ 749.901015] [ T8673] run fstests cifs/001 at 2025-06-17 09:40:30 [ 750.346409] [ T9870] ================================================================== [ 750.346814] [ T9870] BUG: KASAN: slab-out-of-bounds in smb_set_sge+0x2cc/0x3b0 [cifs] [ 750.347330] [ T9870] Write of size 8 at addr ffff888011082890 by task xfs_io/9870 [ 750.347705] [ T9870] [ 750.348077] [ T9870] CPU: 0 UID: 0 PID: 9870 Comm: xfs_io Kdump: loaded Not tainted 6.16.0-rc2-metze.02+ #1 PREEMPT(voluntary) [ 750.348082] [ T9870] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 750.348085] [ T9870] Call Trace: [ 750.348086] [ T9870] <TASK> [ 750.348088] [ T9870] dump_stack_lvl+0x76/0xa0 [ 750.348106] [ T9870] print_report+0xd1/0x640 [ 750.348116] [ T9870] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 750.348120] [ T9870] ? kasan_complete_mode_report_info+0x26/0x210 [ 750.348124] [ T9870] kasan_report+0xe7/0x130 [ 750.348128] [ T9870] ? smb_set_sge+0x2cc/0x3b0 [cifs] [ 750.348262] [ T9870] ? smb_set_sge+0x2cc/0x3b0 [cifs] [ 750.348377] [ T9870] __asan_report_store8_noabort+0x17/0x30 [ 750.348381] [ T9870] smb_set_sge+0x2cc/0x3b0 [cifs] [ 750.348496] [ T9870] smbd_post_send_iter+0x1990/0x3070 [cifs] [ 750.348625] [ T9870] ? __pfx_smbd_post_send_iter+0x10/0x10 [cifs] [ 750.348741] [ T9870] ? update_stack_state+0x2a0/0x670 [ 750.348749] [ T9870] ? cifs_flush+0x153/0x320 [cifs] [ 750.348870] [ T9870] ? cifs_flush+0x153/0x320 [cifs] [ 750.348990] [ T9870] ? update_stack_state+0x2a0/0x670 [ 750.348995] [ T9870] smbd_send+0x58c/0x9c0 [cifs] [ 750.349117] [ T9870] ? __pfx_smbd_send+0x10/0x10 [cifs] [ 750.349231] [ T9870] ? unwind_get_return_address+0x65/0xb0 [ 750.349235] [ T9870] ? __pfx_stack_trace_consume_entry+0x10/0x10 [ 750.349242] [ T9870] ? arch_stack_walk+0xa7/0x100 [ 750.349250] [ T9870] ? stack_trace_save+0x92/0xd0 [ 750.349254] [ T9870] __smb_send_rqst+0x931/0xec0 [cifs] [ 750.349374] [ T9870] ? kernel_text_address+0x173/0x190 [ 750.349379] [ T9870] ? kasan_save_stack+0x39/0x70 [ 750.349382] [ T9870] ? kasan_save_track+0x18/0x70 [ 750.349385] [ T9870] ? __kasan_slab_alloc+0x9d/0xa0 [ 750.349389] [ T9870] ? __pfx___smb_send_rqst+0x10/0x10 [cifs] [ 750.349508] [ T9870] ? smb2_mid_entry_alloc+0xb4/0x7e0 [cifs] [ 750.349626] [ T9870] ? cifs_call_async+0x277/0xb00 [cifs] [ 750.349746] [ T9870] ? cifs_issue_write+0x256/0x610 [cifs] [ 750.349867] [ T9870] ? netfs_do_issue_write+0xc2/0x340 [netfs] [ 750.349900] [ T9870] ? netfs_advance_write+0x45b/0x1270 [netfs] [ 750.349929] [ T9870] ? netfs_write_folio+0xd6c/0x1be0 [netfs] [ 750.349958] [ T9870] ? netfs_writepages+0x2e9/0xa80 [netfs] [ 750.349987] [ T9870] ? do_writepages+0x21f/0x590 [ 750.349993] [ T9870] ? filemap_fdatawrite_wbc+0xe1/0x140 [ 750.349997] [ T9870] ? entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 750.350002] [ T9870] smb_send_rqst+0x22e/0x2f0 [cifs] [ 750.350131] [ T9870] ? __pfx_smb_send_rqst+0x10/0x10 [cifs] [ 750.350255] [ T9870] ? local_clock_noinstr+0xe/0xd0 [ 750.350261] [ T9870] ? kasan_save_alloc_info+0x37/0x60 [ 750.350268] [ T9870] ? __kasan_check_write+0x14/0x30 [ 750.350271] [ T9870] ? _raw_spin_lock+0x81/0xf0 [ 750.350275] [ T9870] ? __pfx__raw_spin_lock+0x10/0x10 [ 750.350278] [ T9870] ? smb2_setup_async_request+0x293/0x580 [cifs] [ 750.350398] [ T9870] cifs_call_async+0x477/0xb00 [cifs] [ 750.350518] [ T9870] ? __pfx_smb2_writev_callback+0x10/0x10 [cifs] [ 750.350636] [ T9870] ? __pfx_cifs_call_async+0x10/0x10 [cifs] [ 750.350756] [ T9870] ? __pfx__raw_spin_lock+0x10/0x10 [ 750.350760] [ T9870] ? __kasan_check_write+0x14/0x30 [ 750.350763] [ T98 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: gadget: check that event count does not exceed event buffer length The event count is read from register DWC3_GEVNTCOUNT. There is a check for the count being zero, but not for exceeding the event buffer length. Check that event count does not exceed event buffer length, avoiding an out-of-bounds access when memcpy'ing the event. Crash log: Unable to handle kernel paging request at virtual address ffffffc0129be000 pc : __memcpy+0x114/0x180 lr : dwc3_check_event_buf+0xec/0x348 x3 : 0000000000000030 x2 : 000000000000dfc4 x1 : ffffffc0129be000 x0 : ffffff87aad60080 Call trace: __memcpy+0x114/0x180 dwc3_interrupt+0x24/0x34

In the Linux kernel, the following vulnerability has been resolved: ASoC: qcom: Fix sc7280 lpass potential buffer overflow Case values introduced in commit 5f78e1fb7a3e ("ASoC: qcom: Add driver support for audioreach solution") cause out of bounds access in arrays of sc7280 driver data (e.g. in case of RX_CODEC_DMA_RX_0 in sc7280_snd_hw_params()). Redefine LPASS_MAX_PORTS to consider the maximum possible port id for q6dsp as sc7280 driver utilizes some of those values. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: prevent out-of-bounds stream writes by validating *pos ksmbd_vfs_stream_write() did not validate whether the write offset (*pos) was within the bounds of the existing stream data length (v_len). If *pos was greater than or equal to v_len, this could lead to an out-of-bounds memory write. This patch adds a check to ensure *pos is less than v_len before proceeding. If the condition fails, -EINVAL is returned.

In the Linux kernel, the following vulnerability has been resolved: tracing: Fix oob write in trace_seq_to_buffer() syzbot reported this bug: ================================================================== BUG: KASAN: slab-out-of-bounds in trace_seq_to_buffer kernel/trace/trace.c:1830 [inline] BUG: KASAN: slab-out-of-bounds in tracing_splice_read_pipe+0x6be/0xdd0 kernel/trace/trace.c:6822 Write of size 4507 at addr ffff888032b6b000 by task syz.2.320/7260 CPU: 1 UID: 0 PID: 7260 Comm: syz.2.320 Not tainted 6.15.0-rc1-syzkaller-00301-g3bde70a2c827 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xc3/0x670 mm/kasan/report.c:521 kasan_report+0xe0/0x110 mm/kasan/report.c:634 check_region_inline mm/kasan/generic.c:183 [inline] kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189 __asan_memcpy+0x3c/0x60 mm/kasan/shadow.c:106 trace_seq_to_buffer kernel/trace/trace.c:1830 [inline] tracing_splice_read_pipe+0x6be/0xdd0 kernel/trace/trace.c:6822 .... ================================================================== It has been reported that trace_seq_to_buffer() tries to copy more data than PAGE_SIZE to buf. Therefore, to prevent this, we should use the smaller of trace_seq_used(&iter->seq) and PAGE_SIZE as an argument.

In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Do not trigger WARN_ON() due to a commit_overrun When reading a memory mapped buffer the reader page is just swapped out with the last page written in the write buffer. If the reader page is the same as the commit buffer (the buffer that is currently being written to) it was assumed that it should never have missed events. If it does, it triggers a WARN_ON_ONCE(). But there just happens to be one scenario where this can legitimately happen. That is on a commit_overrun. A commit overrun is when an interrupt preempts an event being written to the buffer and then the interrupt adds so many new events that it fills and wraps the buffer back to the commit. Any new events would then be dropped and be reported as "missed_events". In this case, the next page to read is the commit buffer and after the swap of the reader page, the reader page will be the commit buffer, but this time there will be missed events and this triggers the following warning: ------------[ cut here ]------------ WARNING: CPU: 2 PID: 1127 at kernel/trace/ring_buffer.c:7357 ring_buffer_map_get_reader+0x49a/0x780 Modules linked in: kvm_intel kvm irqbypass CPU: 2 UID: 0 PID: 1127 Comm: trace-cmd Not tainted 6.15.0-rc7-test-00004-g478bc2824b45-dirty #564 PREEMPT Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:ring_buffer_map_get_reader+0x49a/0x780 Code: 00 00 00 48 89 fe 48 c1 ee 03 80 3c 2e 00 0f 85 ec 01 00 00 4d 3b a6 a8 00 00 00 0f 85 8a fd ff ff 48 85 c0 0f 84 55 fe ff ff <0f> 0b e9 4e fe ff ff be 08 00 00 00 4c 89 54 24 58 48 89 54 24 50 RSP: 0018:ffff888121787dc0 EFLAGS: 00010002 RAX: 00000000000006a2 RBX: ffff888100062800 RCX: ffffffff8190cb49 RDX: ffff888126934c00 RSI: 1ffff11020200a15 RDI: ffff8881010050a8 RBP: dffffc0000000000 R08: 0000000000000000 R09: ffffed1024d26982 R10: ffff888126934c17 R11: ffff8881010050a8 R12: ffff888126934c00 R13: ffff8881010050b8 R14: ffff888101005000 R15: ffff888126930008 FS: 00007f95c8cd7540(0000) GS:ffff8882b576e000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f95c8de4dc0 CR3: 0000000128452002 CR4: 0000000000172ef0 Call Trace: <TASK> ? __pfx_ring_buffer_map_get_reader+0x10/0x10 tracing_buffers_ioctl+0x283/0x370 __x64_sys_ioctl+0x134/0x190 do_syscall_64+0x79/0x1c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f95c8de48db Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <89> c2 3d 00 f0 ff ff 77 1c 48 8b 44 24 18 64 48 2b 04 25 28 00 00 RSP: 002b:00007ffe037ba110 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffe037bb2b0 RCX: 00007f95c8de48db RDX: 0000000000000000 RSI: 0000000000005220 RDI: 0000000000000006 RBP: 00007ffe037ba180 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffe037bb6f8 R14: 00007f95c9065000 R15: 00005575c7492c90 </TASK> irq event stamp: 5080 hardirqs last enabled at (5079): [<ffffffff83e0adb0>] _raw_spin_unlock_irqrestore+0x50/0x70 hardirqs last disabled at (5080): [<ffffffff83e0aa83>] _raw_spin_lock_irqsave+0x63/0x70 softirqs last enabled at (4182): [<ffffffff81516122>] handle_softirqs+0x552/0x710 softirqs last disabled at (4159): [<ffffffff815163f7>] __irq_exit_rcu+0x107/0x210 ---[ end trace 0000000000000000 ]--- The above was triggered by running on a kernel with both lockdep and KASAN as well as kmemleak enabled and executing the following command: # perf record -o perf-test.dat -a -- trace-cmd record --nosplice -e all -p function hackbench 50 With perf interjecting a lot of interrupts and trace-cmd enabling all events as well as function tracing, with lockdep, KASAN and kmemleak enabled, it could cause an interrupt preempting an event being written to add enough event ---truncated---

In the Linux kernel, the following vulnerability has been resolved: platform/x86: dell-wmi-sysman: Avoid buffer overflow in current_password_store() If the 'buf' array received from the user contains an empty string, the 'length' variable will be zero. Accessing the 'buf' array element with index 'length - 1' will result in a buffer overflow. Add a check for an empty string. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: EDAC/skx_common: Fix general protection fault After loading i10nm_edac (which automatically loads skx_edac_common), if unload only i10nm_edac, then reload it and perform error injection testing, a general protection fault may occur: mce: [Hardware Error]: Machine check events logged Oops: general protection fault ... ... Workqueue: events mce_gen_pool_process RIP: 0010:string+0x53/0xe0 ... Call Trace: <TASK> ? die_addr+0x37/0x90 ? exc_general_protection+0x1e7/0x3f0 ? asm_exc_general_protection+0x26/0x30 ? string+0x53/0xe0 vsnprintf+0x23e/0x4c0 snprintf+0x4d/0x70 skx_adxl_decode+0x16a/0x330 [skx_edac_common] skx_mce_check_error.part.0+0xf8/0x220 [skx_edac_common] skx_mce_check_error+0x17/0x20 [skx_edac_common] ... The issue arose was because the variable 'adxl_component_count' (inside skx_edac_common), which counts the ADXL components, was not reset. During the reloading of i10nm_edac, the count was incremented by the actual number of ADXL components again, resulting in a count that was double the real number of ADXL components. This led to an out-of-bounds reference to the ADXL component array, causing the general protection fault above. Fix this issue by resetting the 'adxl_component_count' in adxl_put(), which is called during the unloading of {skx,i10nm}_edac.

IBM DB2 High Performance Unload 6.1.0.3, 5.1.0.1, 6.1.0.2, 6.5, 6.5.0.0 IF1, 6.1.0.1, 6.1, and 5.1 could allow an authenticated user to cause the program to crash due an out of bounds write.

In the Linux kernel, the following vulnerability has been resolved: arm64: entry: avoid kprobe recursion The cortex_a76_erratum_1463225_debug_handler() function is called when handling debug exceptions (and synchronous exceptions from BRK instructions), and so is called when a probed function executes. If the compiler does not inline cortex_a76_erratum_1463225_debug_handler(), it can be probed. If cortex_a76_erratum_1463225_debug_handler() is probed, any debug exception or software breakpoint exception will result in recursive exceptions leading to a stack overflow. This can be triggered with the ftrace multiple_probes selftest, and as per the example splat below. This is a regression caused by commit: 6459b8469753e9fe ("arm64: entry: consolidate Cortex-A76 erratum 1463225 workaround") ... which removed the NOKPROBE_SYMBOL() annotation associated with the function. My intent was that cortex_a76_erratum_1463225_debug_handler() would be inlined into its caller, el1_dbg(), which is marked noinstr and cannot be probed. Mark cortex_a76_erratum_1463225_debug_handler() as __always_inline to ensure this. Example splat prior to this patch (with recursive entries elided): | # echo p cortex_a76_erratum_1463225_debug_handler > /sys/kernel/debug/tracing/kprobe_events | # echo p do_el0_svc >> /sys/kernel/debug/tracing/kprobe_events | # echo 1 > /sys/kernel/debug/tracing/events/kprobes/enable | Insufficient stack space to handle exception! | ESR: 0x0000000096000047 -- DABT (current EL) | FAR: 0xffff800009cefff0 | Task stack: [0xffff800009cf0000..0xffff800009cf4000] | IRQ stack: [0xffff800008000000..0xffff800008004000] | Overflow stack: [0xffff00007fbc00f0..0xffff00007fbc10f0] | CPU: 0 PID: 145 Comm: sh Not tainted 6.0.0 #2 | Hardware name: linux,dummy-virt (DT) | pstate: 604003c5 (nZCv DAIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) | pc : arm64_enter_el1_dbg+0x4/0x20 | lr : el1_dbg+0x24/0x5c | sp : ffff800009cf0000 | x29: ffff800009cf0000 x28: ffff000002c74740 x27: 0000000000000000 | x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 | x23: 00000000604003c5 x22: ffff80000801745c x21: 0000aaaac95ac068 | x20: 00000000f2000004 x19: ffff800009cf0040 x18: 0000000000000000 | x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 | x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 | x11: 0000000000000010 x10: ffff800008c87190 x9 : ffff800008ca00d0 | x8 : 000000000000003c x7 : 0000000000000000 x6 : 0000000000000000 | x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000000043a4 | x2 : 00000000f2000004 x1 : 00000000f2000004 x0 : ffff800009cf0040 | Kernel panic - not syncing: kernel stack overflow | CPU: 0 PID: 145 Comm: sh Not tainted 6.0.0 #2 | Hardware name: linux,dummy-virt (DT) | Call trace: | dump_backtrace+0xe4/0x104 | show_stack+0x18/0x4c | dump_stack_lvl+0x64/0x7c | dump_stack+0x18/0x38 | panic+0x14c/0x338 | test_taint+0x0/0x2c | panic_bad_stack+0x104/0x118 | handle_bad_stack+0x34/0x48 | __bad_stack+0x78/0x7c | arm64_enter_el1_dbg+0x4/0x20 | el1h_64_sync_handler+0x40/0x98 | el1h_64_sync+0x64/0x68 | cortex_a76_erratum_1463225_debug_handler+0x0/0x34 ... | el1h_64_sync_handler+0x40/0x98 | el1h_64_sync+0x64/0x68 | cortex_a76_erratum_1463225_debug_handler+0x0/0x34 ... | el1h_64_sync_handler+0x40/0x98 | el1h_64_sync+0x64/0x68 | cortex_a76_erratum_1463225_debug_handler+0x0/0x34 | el1h_64_sync_handler+0x40/0x98 | el1h_64_sync+0x64/0x68 | do_el0_svc+0x0/0x28 | el0t_64_sync_handler+0x84/0xf0 | el0t_64_sync+0x18c/0x190 | Kernel Offset: disabled | CPU features: 0x0080,00005021,19001080 | Memory Limit: none | ---[ end Kernel panic - not syncing: kernel stack overflow ]--- With this patch, cortex_a76_erratum_1463225_debug_handler() is inlined into el1_dbg(), and el1_dbg() cannot be probed: | # echo p cortex_a76_erratum_1463225_debug_handler > /sys/kernel/debug/tracing/kprobe_events | sh: write error: No such file or directory | # grep -w cortex_a76_errat ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ice: Fix memory corruption in VF driver Disable VF's RX/TX queues, when it's disabled. VF can have queues enabled, when it requests a reset. If PF driver assumes that VF is disabled, while VF still has queues configured, VF may unmap DMA resources. In such scenario device still can map packets to memory, which ends up silently corrupting it. Previously, VF driver could experience memory corruption, which lead to crash: [ 5119.170157] BUG: unable to handle kernel paging request at 00001b9780003237 [ 5119.170166] PGD 0 P4D 0 [ 5119.170173] Oops: 0002 [#1] PREEMPT_RT SMP PTI [ 5119.170181] CPU: 30 PID: 427592 Comm: kworker/u96:2 Kdump: loaded Tainted: G W I --------- - - 4.18.0-372.9.1.rt7.166.el8.x86_64 #1 [ 5119.170189] Hardware name: Dell Inc. PowerEdge R740/014X06, BIOS 2.3.10 08/15/2019 [ 5119.170193] Workqueue: iavf iavf_adminq_task [iavf] [ 5119.170219] RIP: 0010:__page_frag_cache_drain+0x5/0x30 [ 5119.170238] Code: 0f 0f b6 77 51 85 f6 74 07 31 d2 e9 05 df ff ff e9 90 fe ff ff 48 8b 05 49 db 33 01 eb b4 0f 1f 80 00 00 00 00 0f 1f 44 00 00 <f0> 29 77 34 74 01 c3 48 8b 07 f6 c4 80 74 0f 0f b6 77 51 85 f6 74 [ 5119.170244] RSP: 0018:ffffa43b0bdcfd78 EFLAGS: 00010282 [ 5119.170250] RAX: ffffffff896b3e40 RBX: ffff8fb282524000 RCX: 0000000000000002 [ 5119.170254] RDX: 0000000049000000 RSI: 0000000000000000 RDI: 00001b9780003203 [ 5119.170259] RBP: ffff8fb248217b00 R08: 0000000000000022 R09: 0000000000000009 [ 5119.170262] R10: 2b849d6300000000 R11: 0000000000000020 R12: 0000000000000000 [ 5119.170265] R13: 0000000000001000 R14: 0000000000000009 R15: 0000000000000000 [ 5119.170269] FS: 0000000000000000(0000) GS:ffff8fb1201c0000(0000) knlGS:0000000000000000 [ 5119.170274] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5119.170279] CR2: 00001b9780003237 CR3: 00000008f3e1a003 CR4: 00000000007726e0 [ 5119.170283] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 5119.170286] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 5119.170290] PKRU: 55555554 [ 5119.170292] Call Trace: [ 5119.170298] iavf_clean_rx_ring+0xad/0x110 [iavf] [ 5119.170324] iavf_free_rx_resources+0xe/0x50 [iavf] [ 5119.170342] iavf_free_all_rx_resources.part.51+0x30/0x40 [iavf] [ 5119.170358] iavf_virtchnl_completion+0xd8a/0x15b0 [iavf] [ 5119.170377] ? iavf_clean_arq_element+0x210/0x280 [iavf] [ 5119.170397] iavf_adminq_task+0x126/0x2e0 [iavf] [ 5119.170416] process_one_work+0x18f/0x420 [ 5119.170429] worker_thread+0x30/0x370 [ 5119.170437] ? process_one_work+0x420/0x420 [ 5119.170445] kthread+0x151/0x170 [ 5119.170452] ? set_kthread_struct+0x40/0x40 [ 5119.170460] ret_from_fork+0x35/0x40 [ 5119.170477] Modules linked in: iavf sctp ip6_udp_tunnel udp_tunnel mlx4_en mlx4_core nfp tls vhost_net vhost vhost_iotlb tap tun xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink bridge stp llc rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache sunrpc intel_rapl_msr iTCO_wdt iTCO_vendor_support dell_smbios wmi_bmof dell_wmi_descriptor dcdbas kvm_intel kvm irqbypass intel_rapl_common isst_if_common skx_edac irdma nfit libnvdimm x86_pkg_temp_thermal i40e intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel ib_uverbs rapl ipmi_ssif intel_cstate intel_uncore mei_me pcspkr acpi_ipmi ib_core mei lpc_ich i2c_i801 ipmi_si ipmi_devintf wmi ipmi_msghandler acpi_power_meter xfs libcrc32c sd_mod t10_pi sg mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ice ahci drm libahci crc32c_intel libata tg3 megaraid_sas [ 5119.170613] i2c_algo_bit dm_mirror dm_region_hash dm_log dm_mod fuse [last unloaded: iavf] [ 5119.170627] CR2: 00001b9780003237

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gem: add missing boundary check in vm_access A missing bounds check in vm_access() can lead to an out-of-bounds read or write in the adjacent memory area, since the len attribute is not validated before the memcpy later in the function, potentially hitting: [ 183.637831] BUG: unable to handle page fault for address: ffffc90000c86000 [ 183.637934] #PF: supervisor read access in kernel mode [ 183.637997] #PF: error_code(0x0000) - not-present page [ 183.638059] PGD 100000067 P4D 100000067 PUD 100258067 PMD 106341067 PTE 0 [ 183.638144] Oops: 0000 [#2] PREEMPT SMP NOPTI [ 183.638201] CPU: 3 PID: 1790 Comm: poc Tainted: G D 5.17.0-rc6-ci-drm-11296+ #1 [ 183.638298] Hardware name: Intel Corporation CoffeeLake Client Platform/CoffeeLake H DDR4 RVP, BIOS CNLSFWR1.R00.X208.B00.1905301319 05/30/2019 [ 183.638430] RIP: 0010:memcpy_erms+0x6/0x10 [ 183.640213] RSP: 0018:ffffc90001763d48 EFLAGS: 00010246 [ 183.641117] RAX: ffff888109c14000 RBX: ffff888111bece40 RCX: 0000000000000ffc [ 183.642029] RDX: 0000000000001000 RSI: ffffc90000c86000 RDI: ffff888109c14004 [ 183.642946] RBP: 0000000000000ffc R08: 800000000000016b R09: 0000000000000000 [ 183.643848] R10: ffffc90000c85000 R11: 0000000000000048 R12: 0000000000001000 [ 183.644742] R13: ffff888111bed190 R14: ffff888109c14000 R15: 0000000000001000 [ 183.645653] FS: 00007fe5ef807540(0000) GS:ffff88845b380000(0000) knlGS:0000000000000000 [ 183.646570] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 183.647481] CR2: ffffc90000c86000 CR3: 000000010ff02006 CR4: 00000000003706e0 [ 183.648384] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 183.649271] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 183.650142] Call Trace: [ 183.650988] <TASK> [ 183.651793] vm_access+0x1f0/0x2a0 [i915] [ 183.652726] __access_remote_vm+0x224/0x380 [ 183.653561] mem_rw.isra.0+0xf9/0x190 [ 183.654402] vfs_read+0x9d/0x1b0 [ 183.655238] ksys_read+0x63/0xe0 [ 183.656065] do_syscall_64+0x38/0xc0 [ 183.656882] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 183.657663] RIP: 0033:0x7fe5ef725142 [ 183.659351] RSP: 002b:00007ffe1e81c7e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 [ 183.660227] RAX: ffffffffffffffda RBX: 0000557055dfb780 RCX: 00007fe5ef725142 [ 183.661104] RDX: 0000000000001000 RSI: 00007ffe1e81d880 RDI: 0000000000000005 [ 183.661972] RBP: 00007ffe1e81e890 R08: 0000000000000030 R09: 0000000000000046 [ 183.662832] R10: 0000557055dfc2e0 R11: 0000000000000246 R12: 0000557055dfb1c0 [ 183.663691] R13: 00007ffe1e81e980 R14: 0000000000000000 R15: 0000000000000000 Changes since v1: - Updated if condition with range_overflows_t [Chris Wilson] [mauld: tidy up the commit message and add Cc: stable] (cherry picked from commit 661412e301e2ca86799aa4f400d1cf0bd38c57c6)

In the Linux kernel, the following vulnerability has been resolved: btrfs: prevent copying too big compressed lzo segment Compressed length can be corrupted to be a lot larger than memory we have allocated for buffer. This will cause memcpy in copy_compressed_segment to write outside of allocated memory. This mostly results in stuck read syscall but sometimes when using btrfs send can get #GP kernel: general protection fault, probably for non-canonical address 0x841551d5c1000: 0000 [#1] PREEMPT SMP NOPTI kernel: CPU: 17 PID: 264 Comm: kworker/u256:7 Tainted: P OE 5.17.0-rc2-1 #12 kernel: Workqueue: btrfs-endio btrfs_work_helper [btrfs] kernel: RIP: 0010:lzo_decompress_bio (./include/linux/fortify-string.h:225 fs/btrfs/lzo.c:322 fs/btrfs/lzo.c:394) btrfs Code starting with the faulting instruction =========================================== 0:* 48 8b 06 mov (%rsi),%rax <-- trapping instruction 3: 48 8d 79 08 lea 0x8(%rcx),%rdi 7: 48 83 e7 f8 and $0xfffffffffffffff8,%rdi b: 48 89 01 mov %rax,(%rcx) e: 44 89 f0 mov %r14d,%eax 11: 48 8b 54 06 f8 mov -0x8(%rsi,%rax,1),%rdx kernel: RSP: 0018:ffffb110812efd50 EFLAGS: 00010212 kernel: RAX: 0000000000001000 RBX: 000000009ca264c8 RCX: ffff98996e6d8ff8 kernel: RDX: 0000000000000064 RSI: 000841551d5c1000 RDI: ffffffff9500435d kernel: RBP: ffff989a3be856c0 R08: 0000000000000000 R09: 0000000000000000 kernel: R10: 0000000000000000 R11: 0000000000001000 R12: ffff98996e6d8000 kernel: R13: 0000000000000008 R14: 0000000000001000 R15: 000841551d5c1000 kernel: FS: 0000000000000000(0000) GS:ffff98a09d640000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00001e9f984d9ea8 CR3: 000000014971a000 CR4: 00000000003506e0 kernel: Call Trace: kernel: <TASK> kernel: end_compressed_bio_read (fs/btrfs/compression.c:104 fs/btrfs/compression.c:1363 fs/btrfs/compression.c:323) btrfs kernel: end_workqueue_fn (fs/btrfs/disk-io.c:1923) btrfs kernel: btrfs_work_helper (fs/btrfs/async-thread.c:326) btrfs kernel: process_one_work (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:212 ./include/trace/events/workqueue.h:108 kernel/workqueue.c:2312) kernel: worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2455) kernel: ? process_one_work (kernel/workqueue.c:2397) kernel: kthread (kernel/kthread.c:377) kernel: ? kthread_complete_and_exit (kernel/kthread.c:332) kernel: ret_from_fork (arch/x86/entry/entry_64.S:301) kernel: </TASK>

In the Linux kernel, the following vulnerability has been resolved: efi: runtime: Fix potential overflow of soft-reserved region size md_size will have been narrowed if we have >= 4GB worth of pages in a soft-reserved region.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Stop parsing channels bits when all channels are found. If a usb audio device sets more bits than the amount of channels it could write outside of the map array.

uWebSockets 18.11.0 and 18.12.0 has a stack-based buffer overflow in uWS::TopicTree::trimTree (called from uWS::TopicTree::unsubscribeAll). NOTE: the vendor's position is that this is "a minor issue or not even an issue at all" because the developer of an application (that uses uWebSockets) should not be allowing the large number of triggered topics to accumulate

In the Linux kernel, the following vulnerability has been resolved: igc: avoid returning frame twice in XDP_REDIRECT When a frame can not be transmitted in XDP_REDIRECT (e.g. due to a full queue), it is necessary to free it by calling xdp_return_frame_rx_napi. However, this is the responsibility of the caller of the ndo_xdp_xmit (see for example bq_xmit_all in kernel/bpf/devmap.c) and thus calling it inside igc_xdp_xmit (which is the ndo_xdp_xmit of the igc driver) as well will lead to memory corruption. In fact, bq_xmit_all expects that it can return all frames after the last successfully transmitted one. Therefore, break for the first not transmitted frame, but do not call xdp_return_frame_rx_napi in igc_xdp_xmit. This is equally implemented in other Intel drivers such as the igb. There are two alternatives to this that were rejected: 1. Return num_frames as all the frames would have been transmitted and release them inside igc_xdp_xmit. While it might work technically, it is not what the return value is meant to represent (i.e. the number of SUCCESSFULLY transmitted packets). 2. Rework kernel/bpf/devmap.c and all drivers to support non-consecutively dropped packets. Besides being complex, it likely has a negative performance impact without a significant gain since it is anyway unlikely that the next frame can be transmitted if the previous one was dropped. The memory corruption can be reproduced with the following script which leads to a kernel panic after a few seconds. It basically generates more traffic than a i225 NIC can transmit and pushes it via XDP_REDIRECT from a virtual interface to the physical interface where frames get dropped. #!/bin/bash INTERFACE=enp4s0 INTERFACE_IDX=`cat /sys/class/net/$INTERFACE/ifindex` sudo ip link add dev veth1 type veth peer name veth2 sudo ip link set up $INTERFACE sudo ip link set up veth1 sudo ip link set up veth2 cat << EOF > redirect.bpf.c SEC("prog") int redirect(struct xdp_md *ctx) { return bpf_redirect($INTERFACE_IDX, 0); } char _license[] SEC("license") = "GPL"; EOF clang -O2 -g -Wall -target bpf -c redirect.bpf.c -o redirect.bpf.o sudo ip link set veth2 xdp obj redirect.bpf.o cat << EOF > pass.bpf.c SEC("prog") int pass(struct xdp_md *ctx) { return XDP_PASS; } char _license[] SEC("license") = "GPL"; EOF clang -O2 -g -Wall -target bpf -c pass.bpf.c -o pass.bpf.o sudo ip link set $INTERFACE xdp obj pass.bpf.o cat << EOF > trafgen.cfg { /* Ethernet Header */ 0xe8, 0x6a, 0x64, 0x41, 0xbf, 0x46, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, const16(ETH_P_IP), /* IPv4 Header */ 0b01000101, 0, # IPv4 version, IHL, TOS const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header)) const16(2), # IPv4 ident 0b01000000, 0, # IPv4 flags, fragmentation off 64, # IPv4 TTL 17, # Protocol UDP csumip(14, 33), # IPv4 checksum /* UDP Header */ 10, 0, 1, 1, # IP Src - adapt as needed 10, 0, 1, 2, # IP Dest - adapt as needed const16(6666), # UDP Src Port const16(6666), # UDP Dest Port const16(1008), # UDP length (UDP header 8 bytes + payload length) csumudp(14, 34), # UDP checksum /* Payload */ fill('W', 1000), } EOF sudo trafgen -i trafgen.cfg -b3000MB -o veth1 --cpp

In the Linux kernel, the following vulnerability has been resolved: libbpf: Use OPTS_SET() macro in bpf_xdp_query() When the feature_flags and xdp_zc_max_segs fields were added to the libbpf bpf_xdp_query_opts, the code writing them did not use the OPTS_SET() macro. This causes libbpf to write to those fields unconditionally, which means that programs compiled against an older version of libbpf (with a smaller size of the bpf_xdp_query_opts struct) will have its stack corrupted by libbpf writing out of bounds. The patch adding the feature_flags field has an early bail out if the feature_flags field is not part of the opts struct (via the OPTS_HAS) macro, but the patch adding xdp_zc_max_segs does not. For consistency, this fix just changes the assignments to both fields to use the OPTS_SET() macro.

In the Linux kernel, the following vulnerability has been resolved: init/main.c: Fix potential static_command_line memory overflow We allocate memory of size 'xlen + strlen(boot_command_line) + 1' for static_command_line, but the strings copied into static_command_line are extra_command_line and command_line, rather than extra_command_line and boot_command_line. When strlen(command_line) > strlen(boot_command_line), static_command_line will overflow. This patch just recovers strlen(command_line) which was miss-consolidated with strlen(boot_command_line) in the commit f5c7310ac73e ("init/main: add checks for the return value of memblock_alloc*()")

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays The frequency table arrays are supposed to be terminated with an empty element. Add such entry to the end of the arrays where it is missing in order to avoid possible out-of-bound access when the table is traversed by functions like qcom_find_freq() or qcom_find_freq_floor(). Only compile tested.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conntrack_h323: Add protection for bmp length out of range UBSAN load reports an exception of BRK#5515 SHIFT_ISSUE:Bitwise shifts that are out of bounds for their data type. vmlinux get_bitmap(b=75) + 712 <net/netfilter/nf_conntrack_h323_asn1.c:0> vmlinux decode_seq(bs=0xFFFFFFD008037000, f=0xFFFFFFD008037018, level=134443100) + 1956 <net/netfilter/nf_conntrack_h323_asn1.c:592> vmlinux decode_choice(base=0xFFFFFFD0080370F0, level=23843636) + 1216 <net/netfilter/nf_conntrack_h323_asn1.c:814> vmlinux decode_seq(f=0xFFFFFFD0080371A8, level=134443500) + 812 <net/netfilter/nf_conntrack_h323_asn1.c:576> vmlinux decode_choice(base=0xFFFFFFD008037280, level=0) + 1216 <net/netfilter/nf_conntrack_h323_asn1.c:814> vmlinux DecodeRasMessage() + 304 <net/netfilter/nf_conntrack_h323_asn1.c:833> vmlinux ras_help() + 684 <net/netfilter/nf_conntrack_h323_main.c:1728> vmlinux nf_confirm() + 188 <net/netfilter/nf_conntrack_proto.c:137> Due to abnormal data in skb->data, the extension bitmap length exceeds 32 when decoding ras message then uses the length to make a shift operation. It will change into negative after several loop. UBSAN load could detect a negative shift as an undefined behaviour and reports exception. So we add the protection to avoid the length exceeding 32. Or else it will return out of range error and stop decoding.

In the Linux kernel, the following vulnerability has been resolved: s390/vfio-ap: always filter entire AP matrix The vfio_ap_mdev_filter_matrix function is called whenever a new adapter or domain is assigned to the mdev. The purpose of the function is to update the guest's AP configuration by filtering the matrix of adapters and domains assigned to the mdev. When an adapter or domain is assigned, only the APQNs associated with the APID of the new adapter or APQI of the new domain are inspected. If an APQN does not reference a queue device bound to the vfio_ap device driver, then it's APID will be filtered from the mdev's matrix when updating the guest's AP configuration. Inspecting only the APID of the new adapter or APQI of the new domain will result in passing AP queues through to a guest that are not bound to the vfio_ap device driver under certain circumstances. Consider the following: guest's AP configuration (all also assigned to the mdev's matrix): 14.0004 14.0005 14.0006 16.0004 16.0005 16.0006 unassign domain 4 unbind queue 16.0005 assign domain 4 When domain 4 is re-assigned, since only domain 4 will be inspected, the APQNs that will be examined will be: 14.0004 16.0004 Since both of those APQNs reference queue devices that are bound to the vfio_ap device driver, nothing will get filtered from the mdev's matrix when updating the guest's AP configuration. Consequently, queue 16.0005 will get passed through despite not being bound to the driver. This violates the linux device model requirement that a guest shall only be given access to devices bound to the device driver facilitating their pass-through. To resolve this problem, every adapter and domain assigned to the mdev will be inspected when filtering the mdev's matrix.

In the Linux kernel, the following vulnerability has been resolved: parisc: Fix random data corruption from exception handler The current exception handler implementation, which assists when accessing user space memory, may exhibit random data corruption if the compiler decides to use a different register than the specified register %r29 (defined in ASM_EXCEPTIONTABLE_REG) for the error code. If the compiler choose another register, the fault handler will nevertheless store -EFAULT into %r29 and thus trash whatever this register is used for. Looking at the assembly I found that this happens sometimes in emulate_ldd(). To solve the issue, the easiest solution would be if it somehow is possible to tell the fault handler which register is used to hold the error code. Using %0 or %1 in the inline assembly is not posssible as it will show up as e.g. %r29 (with the "%r" prefix), which the GNU assembler can not convert to an integer. This patch takes another, better and more flexible approach: We extend the __ex_table (which is out of the execution path) by one 32-word. In this word we tell the compiler to insert the assembler instruction "or %r0,%r0,%reg", where %reg references the register which the compiler choosed for the error return code. In case of an access failure, the fault handler finds the __ex_table entry and can examine the opcode. The used register is encoded in the lowest 5 bits, and the fault handler can then store -EFAULT into this register. Since we extend the __ex_table to 3 words we can't use the BUILDTIME_TABLE_SORT config option any longer.

In the Linux kernel, the following vulnerability has been resolved: xhci: handle isoc Babble and Buffer Overrun events properly xHCI 4.9 explicitly forbids assuming that the xHC has released its ownership of a multi-TRB TD when it reports an error on one of the early TRBs. Yet the driver makes such assumption and releases the TD, allowing the remaining TRBs to be freed or overwritten by new TDs. The xHC should also report completion of the final TRB due to its IOC flag being set by us, regardless of prior errors. This event cannot be recognized if the TD has already been freed earlier, resulting in "Transfer event TRB DMA ptr not part of current TD" error message. Fix this by reusing the logic for processing isoc Transaction Errors. This also handles hosts which fail to report the final completion. Fix transfer length reporting on Babble errors. They may be caused by device malfunction, no guarantee that the buffer has been filled.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (nct6775) Fix access to temperature configuration registers The number of temperature configuration registers does not always match the total number of temperature registers. This can result in access errors reported if KASAN is enabled. BUG: KASAN: global-out-of-bounds in nct6775_probe+0x5654/0x6fe9 nct6775_core

In the Linux kernel, the following vulnerability has been resolved: afs: Increase buffer size in afs_update_volume_status() The max length of volume->vid value is 20 characters. So increase idbuf[] size up to 24 to avoid overflow. Found by Linux Verification Center (linuxtesting.org) with SVACE. [DH: Actually, it's 20 + NUL, so increase it to 24 and use snprintf()]

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix data corruption in dsync block recovery for small block sizes The helper function nilfs_recovery_copy_block() of nilfs_recovery_dsync_blocks(), which recovers data from logs created by data sync writes during a mount after an unclean shutdown, incorrectly calculates the on-page offset when copying repair data to the file's page cache. In environments where the block size is smaller than the page size, this flaw can cause data corruption and leak uninitialized memory bytes during the recovery process. Fix these issues by correcting this byte offset calculation on the page.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: fix a memory corruption iwl_fw_ini_trigger_tlv::data is a pointer to a __le32, which means that if we copy to iwl_fw_ini_trigger_tlv::data + offset while offset is in bytes, we'll write past the buffer.

In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_acl_tcam: Fix stack corruption When tc filters are first added to a net device, the corresponding local port gets bound to an ACL group in the device. The group contains a list of ACLs. In turn, each ACL points to a different TCAM region where the filters are stored. During forwarding, the ACLs are sequentially evaluated until a match is found. One reason to place filters in different regions is when they are added with decreasing priorities and in an alternating order so that two consecutive filters can never fit in the same region because of their key usage. In Spectrum-2 and newer ASICs the firmware started to report that the maximum number of ACLs in a group is more than 16, but the layout of the register that configures ACL groups (PAGT) was not updated to account for that. It is therefore possible to hit stack corruption [1] in the rare case where more than 16 ACLs in a group are required. Fix by limiting the maximum ACL group size to the minimum between what the firmware reports and the maximum ACLs that fit in the PAGT register. Add a test case to make sure the machine does not crash when this condition is hit. [1] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120 [...] dump_stack_lvl+0x36/0x50 panic+0x305/0x330 __stack_chk_fail+0x15/0x20 mlxsw_sp_acl_tcam_group_update+0x116/0x120 mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110 mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20 mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0 mlxsw_sp_acl_rule_add+0x47/0x240 mlxsw_sp_flower_replace+0x1a9/0x1d0 tc_setup_cb_add+0xdc/0x1c0 fl_hw_replace_filter+0x146/0x1f0 fl_change+0xc17/0x1360 tc_new_tfilter+0x472/0xb90 rtnetlink_rcv_msg+0x313/0x3b0 netlink_rcv_skb+0x58/0x100 netlink_unicast+0x244/0x390 netlink_sendmsg+0x1e4/0x440 ____sys_sendmsg+0x164/0x260 ___sys_sendmsg+0x9a/0xe0 __sys_sendmsg+0x7a/0xc0 do_syscall_64+0x40/0xe0 entry_SYSCALL_64_after_hwframe+0x63/0x6b

In the Linux kernel, the following vulnerability has been resolved: Both cadence-quadspi ->runtime_suspend() and ->runtime_resume() implementations start with: struct cqspi_st *cqspi = dev_get_drvdata(dev); struct spi_controller *host = dev_get_drvdata(dev); This obviously cannot be correct, unless "struct cqspi_st" is the first member of " struct spi_controller", or the other way around, but it is not the case. "struct spi_controller" is allocated by devm_spi_alloc_host(), which allocates an extra amount of memory for private data, used to store "struct cqspi_st". The ->probe() function of the cadence-quadspi driver then sets the device drvdata to store the address of the "struct cqspi_st" structure. Therefore: struct cqspi_st *cqspi = dev_get_drvdata(dev); is correct, but: struct spi_controller *host = dev_get_drvdata(dev); is not, as it makes "host" point not to a "struct spi_controller" but to the same "struct cqspi_st" structure as above. This obviously leads to bad things (memory corruption, kernel crashes) directly during ->probe(), as ->probe() enables the device using PM runtime, leading the ->runtime_resume() hook being called, which in turns calls spi_controller_resume() with the wrong pointer. This has at least been reported [0] to cause a kernel crash, but the exact behavior will depend on the memory contents. [0] https://lore.kernel.org/all/20240226121803.5a7r5wkpbbowcxgx@dhruva/ This issue potentially affects all platforms that are currently using the cadence-quadspi driver.

In the Linux kernel, the following vulnerability has been resolved: mm/swap: fix race when skipping swapcache When skipping swapcache for SWP_SYNCHRONOUS_IO, if two or more threads swapin the same entry at the same time, they get different pages (A, B). Before one thread (T0) finishes the swapin and installs page (A) to the PTE, another thread (T1) could finish swapin of page (B), swap_free the entry, then swap out the possibly modified page reusing the same entry. It breaks the pte_same check in (T0) because PTE value is unchanged, causing ABA problem. Thread (T0) will install a stalled page (A) into the PTE and cause data corruption. One possible callstack is like this: CPU0 CPU1 ---- ---- do_swap_page() do_swap_page() with same entry <direct swapin path> <direct swapin path> <alloc page A> <alloc page B> swap_read_folio() <- read to page A swap_read_folio() <- read to page B <slow on later locks or interrupt> <finished swapin first> ... set_pte_at() swap_free() <- entry is free <write to page B, now page A stalled> <swap out page B to same swap entry> pte_same() <- Check pass, PTE seems unchanged, but page A is stalled! swap_free() <- page B content lost! set_pte_at() <- staled page A installed! And besides, for ZRAM, swap_free() allows the swap device to discard the entry content, so even if page (B) is not modified, if swap_read_folio() on CPU0 happens later than swap_free() on CPU1, it may also cause data loss. To fix this, reuse swapcache_prepare which will pin the swap entry using the cache flag, and allow only one thread to swap it in, also prevent any parallel code from putting the entry in the cache. Release the pin after PT unlocked. Racers just loop and wait since it's a rare and very short event. A schedule_timeout_uninterruptible(1) call is added to avoid repeated page faults wasting too much CPU, causing livelock or adding too much noise to perf statistics. A similar livelock issue was described in commit 029c4628b2eb ("mm: swap: get rid of livelock in swapin readahead") Reproducer: This race issue can be triggered easily using a well constructed reproducer and patched brd (with a delay in read path) [1]: With latest 6.8 mainline, race caused data loss can be observed easily: $ gcc -g -lpthread test-thread-swap-race.c && ./a.out Polulating 32MB of memory region... Keep swapping out... Starting round 0... Spawning 65536 workers... 32746 workers spawned, wait for done... Round 0: Error on 0x5aa00, expected 32746, got 32743, 3 data loss! Round 0: Error on 0x395200, expected 32746, got 32743, 3 data loss! Round 0: Error on 0x3fd000, expected 32746, got 32737, 9 data loss! Round 0 Failed, 15 data loss! This reproducer spawns multiple threads sharing the same memory region using a small swap device. Every two threads updates mapped pages one by one in opposite direction trying to create a race, with one dedicated thread keep swapping out the data out using madvise. The reproducer created a reproduce rate of about once every 5 minutes, so the race should be totally possible in production. After this patch, I ran the reproducer for over a few hundred rounds and no data loss observed. Performance overhead is minimal, microbenchmark swapin 10G from 32G zram: Before: 10934698 us After: 11157121 us Cached: 13155355 us (Dropping SWP_SYNCHRONOUS_IO flag) [kasong@tencent.com: v4]

In the Linux kernel, the following vulnerability has been resolved: x86/efistub: Use 1:1 file:memory mapping for PE/COFF .compat section The .compat section is a dummy PE section that contains the address of the 32-bit entrypoint of the 64-bit kernel image if it is bootable from 32-bit firmware (i.e., CONFIG_EFI_MIXED=y) This section is only 8 bytes in size and is only referenced from the loader, and so it is placed at the end of the memory view of the image, to avoid the need for padding it to 4k, which is required for sections appearing in the middle of the image. Unfortunately, this violates the PE/COFF spec, and even if most EFI loaders will work correctly (including the Tianocore reference implementation), PE loaders do exist that reject such images, on the basis that both the file and memory views of the file contents should be described by the section headers in a monotonically increasing manner without leaving any gaps. So reorganize the sections to avoid this issue. This results in a slight padding overhead (< 4k) which can be avoided if desired by disabling CONFIG_EFI_MIXED (which is only needed in rare cases these days)

In the Linux kernel, the following vulnerability has been resolved: arp: Prevent overflow in arp_req_get(). syzkaller reported an overflown write in arp_req_get(). [0] When ioctl(SIOCGARP) is issued, arp_req_get() looks up an neighbour entry and copies neigh->ha to struct arpreq.arp_ha.sa_data. The arp_ha here is struct sockaddr, not struct sockaddr_storage, so the sa_data buffer is just 14 bytes. In the splat below, 2 bytes are overflown to the next int field, arp_flags. We initialise the field just after the memcpy(), so it's not a problem. However, when dev->addr_len is greater than 22 (e.g. MAX_ADDR_LEN), arp_netmask is overwritten, which could be set as htonl(0xFFFFFFFFUL) in arp_ioctl() before calling arp_req_get(). To avoid the overflow, let's limit the max length of memcpy(). Note that commit b5f0de6df6dc ("net: dev: Convert sa_data to flexible array in struct sockaddr") just silenced syzkaller. [0]: memcpy: detected field-spanning write (size 16) of single field "r->arp_ha.sa_data" at net/ipv4/arp.c:1128 (size 14) WARNING: CPU: 0 PID: 144638 at net/ipv4/arp.c:1128 arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Modules linked in: CPU: 0 PID: 144638 Comm: syz-executor.4 Not tainted 6.1.74 #31 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-debian-1.16.0-5 04/01/2014 RIP: 0010:arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Code: fd ff ff e8 41 42 de fb b9 0e 00 00 00 4c 89 fe 48 c7 c2 20 6d ab 87 48 c7 c7 80 6d ab 87 c6 05 25 af 72 04 01 e8 5f 8d ad fb <0f> 0b e9 6c fd ff ff e8 13 42 de fb be 03 00 00 00 4c 89 e7 e8 a6 RSP: 0018:ffffc900050b7998 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff88803a815000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff8641a44a RDI: 0000000000000001 RBP: ffffc900050b7a98 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 203a7970636d656d R12: ffff888039c54000 R13: 1ffff92000a16f37 R14: ffff88803a815084 R15: 0000000000000010 FS: 00007f172bf306c0(0000) GS:ffff88805aa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f172b3569f0 CR3: 0000000057f12005 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> arp_ioctl+0x33f/0x4b0 net/ipv4/arp.c:1261 inet_ioctl+0x314/0x3a0 net/ipv4/af_inet.c:981 sock_do_ioctl+0xdf/0x260 net/socket.c:1204 sock_ioctl+0x3ef/0x650 net/socket.c:1321 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x18e/0x220 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x37/0x90 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x64/0xce RIP: 0033:0x7f172b262b8d Code: 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f172bf300b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f172b3abf80 RCX: 00007f172b262b8d RDX: 0000000020000000 RSI: 0000000000008954 RDI: 0000000000000003 RBP: 00007f172b2d3493 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007f172b3abf80 R15: 00007f172bf10000 </TASK>

In the Linux kernel, the following vulnerability has been resolved: dm-crypt, dm-verity: disable tasklets Tasklets have an inherent problem with memory corruption. The function tasklet_action_common calls tasklet_trylock, then it calls the tasklet callback and then it calls tasklet_unlock. If the tasklet callback frees the structure that contains the tasklet or if it calls some code that may free it, tasklet_unlock will write into free memory. The commits 8e14f610159d and d9a02e016aaf try to fix it for dm-crypt, but it is not a sufficient fix and the data corruption can still happen [1]. There is no fix for dm-verity and dm-verity will write into free memory with every tasklet-processed bio. There will be atomic workqueues implemented in the kernel 6.9 [2]. They will have better interface and they will not suffer from the memory corruption problem. But we need something that stops the memory corruption now and that can be backported to the stable kernels. So, I'm proposing this commit that disables tasklets in both dm-crypt and dm-verity. This commit doesn't remove the tasklet support, because the tasklet code will be reused when atomic workqueues will be implemented. [1] https://lore.kernel.org/all/d390d7ee-f142-44d3-822a-87949e14608b@suse.de/T/ [2] https://lore.kernel.org/lkml/20240130091300.2968534-1-tj@kernel.org/

In the Linux kernel, the following vulnerability has been resolved: hwmon: (coretemp) Fix out-of-bounds memory access Fix a bug that pdata->cpu_map[] is set before out-of-bounds check. The problem might be triggered on systems with more than 128 cores per package.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate payload size in ipc response If installing malicious ksmbd-tools, ksmbd.mountd can return invalid ipc response to ksmbd kernel server. ksmbd should validate payload size of ipc response from ksmbd.mountd to avoid memory overrun or slab-out-of-bounds. This patch validate 3 ipc response that has payload.

In the Linux kernel before 5.4.12, drivers/input/input.c has out-of-bounds writes via a crafted keycode table, as demonstrated by input_set_keycode, aka CID-cb222aed03d7.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: update channel list in reg notifier instead reg worker Currently when ath11k gets a new channel list, it will be processed according to the following steps: 1. update new channel list to cfg80211 and queue reg_work. 2. cfg80211 handles new channel list during reg_work. 3. update cfg80211's handled channel list to firmware by ath11k_reg_update_chan_list(). But ath11k will immediately execute step 3 after reg_work is just queued. Since step 2 is asynchronous, cfg80211 may not have completed handling the new channel list, which may leading to an out-of-bounds write error: BUG: KASAN: slab-out-of-bounds in ath11k_reg_update_chan_list Call Trace: ath11k_reg_update_chan_list+0xbfe/0xfe0 [ath11k] kfree+0x109/0x3a0 ath11k_regd_update+0x1cf/0x350 [ath11k] ath11k_regd_update_work+0x14/0x20 [ath11k] process_one_work+0xe35/0x14c0 Should ensure step 2 is completely done before executing step 3. Thus Wen raised patch[1]. When flag NL80211_REGDOM_SET_BY_DRIVER is set, cfg80211 will notify ath11k after step 2 is done. So enable the flag NL80211_REGDOM_SET_BY_DRIVER then cfg80211 will notify ath11k after step 2 is done. At this time, there will be no KASAN bug during the execution of the step 3. [1] https://patchwork.kernel.org/project/linux-wireless/patch/20230201065313.27203-1-quic_wgong@quicinc.com/ Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix reg_set_min_max corruption of fake_reg Juan reported that after doing some changes to buzzer [0] and implementing a new fuzzing strategy guided by coverage, they noticed the following in one of the probes: [...] 13: (79) r6 = *(u64 *)(r0 +0) ; R0=map_value(ks=4,vs=8) R6_w=scalar() 14: (b7) r0 = 0 ; R0_w=0 15: (b4) w0 = -1 ; R0_w=0xffffffff 16: (74) w0 >>= 1 ; R0_w=0x7fffffff 17: (5c) w6 &= w0 ; R0_w=0x7fffffff R6_w=scalar(smin=smin32=0,smax=umax=umax32=0x7fffffff,var_off=(0x0; 0x7fffffff)) 18: (44) w6 |= 2 ; R6_w=scalar(smin=umin=smin32=umin32=2,smax=umax=umax32=0x7fffffff,var_off=(0x2; 0x7ffffffd)) 19: (56) if w6 != 0x7ffffffd goto pc+1 REG INVARIANTS VIOLATION (true_reg2): range bounds violation u64=[0x7fffffff, 0x7ffffffd] s64=[0x7fffffff, 0x7ffffffd] u32=[0x7fffffff, 0x7ffffffd] s32=[0x7fffffff, 0x7ffffffd] var_off=(0x7fffffff, 0x0) REG INVARIANTS VIOLATION (false_reg1): range bounds violation u64=[0x7fffffff, 0x7ffffffd] s64=[0x7fffffff, 0x7ffffffd] u32=[0x7fffffff, 0x7ffffffd] s32=[0x7fffffff, 0x7ffffffd] var_off=(0x7fffffff, 0x0) REG INVARIANTS VIOLATION (false_reg2): const tnum out of sync with range bounds u64=[0x0, 0xffffffffffffffff] s64=[0x8000000000000000, 0x7fffffffffffffff] u32=[0x0, 0xffffffff] s32=[0x80000000, 0x7fffffff] var_off=(0x7fffffff, 0x0) 19: R6_w=0x7fffffff 20: (95) exit from 19 to 21: R0=0x7fffffff R6=scalar(smin=umin=smin32=umin32=2,smax=umax=smax32=umax32=0x7ffffffe,var_off=(0x2; 0x7ffffffd)) R7=map_ptr(ks=4,vs=8) R9=ctx() R10=fp0 fp-24=map_ptr(ks=4,vs=8) fp-40=mmmmmmmm 21: R0=0x7fffffff R6=scalar(smin=umin=smin32=umin32=2,smax=umax=smax32=umax32=0x7ffffffe,var_off=(0x2; 0x7ffffffd)) R7=map_ptr(ks=4,vs=8) R9=ctx() R10=fp0 fp-24=map_ptr(ks=4,vs=8) fp-40=mmmmmmmm 21: (14) w6 -= 2147483632 ; R6_w=scalar(smin=umin=umin32=2,smax=umax=0xffffffff,smin32=0x80000012,smax32=14,var_off=(0x2; 0xfffffffd)) 22: (76) if w6 s>= 0xe goto pc+1 ; R6_w=scalar(smin=umin=umin32=2,smax=umax=0xffffffff,smin32=0x80000012,smax32=13,var_off=(0x2; 0xfffffffd)) 23: (95) exit from 22 to 24: R0=0x7fffffff R6_w=14 R7=map_ptr(ks=4,vs=8) R9=ctx() R10=fp0 fp-24=map_ptr(ks=4,vs=8) fp-40=mmmmmmmm 24: R0=0x7fffffff R6_w=14 R7=map_ptr(ks=4,vs=8) R9=ctx() R10=fp0 fp-24=map_ptr(ks=4,vs=8) fp-40=mmmmmmmm 24: (14) w6 -= 14 ; R6_w=0 [...] What can be seen here is a register invariant violation on line 19. After the binary-or in line 18, the verifier knows that bit 2 is set but knows nothing about the rest of the content which was loaded from a map value, meaning, range is [2,0x7fffffff] with var_off=(0x2; 0x7ffffffd). When in line 19 the verifier analyzes the branch, it splits the register states in reg_set_min_max() into the registers of the true branch (true_reg1, true_reg2) and the registers of the false branch (false_reg1, false_reg2). Since the test is w6 != 0x7ffffffd, the src_reg is a known constant. Internally, the verifier creates a "fake" register initialized as scalar to the value of 0x7ffffffd, and then passes it onto reg_set_min_max(). Now, for line 19, it is mathematically impossible to take the false branch of this program, yet the verifier analyzes it. It is impossible because the second bit of r6 will be set due to the prior or operation and the constant in the condition has that bit unset (hex(fd) == binary(1111 1101). When the verifier first analyzes the false / fall-through branch, it will compute an intersection between the var_off of r6 and of the constant. This is because the verifier creates a "fake" register initialized to the value of the constant. The intersection result later refines both registers in regs_refine_cond_op(): [...] t = tnum_intersect(tnum_subreg(reg1->var_off), tnum_subreg(reg2->var_off)); reg1->var_o ---truncated---

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix untrusted unsigned subtract Fix the following Smatch static checker warning: net/rxrpc/rxgk_app.c:65 rxgk_yfs_decode_ticket() warn: untrusted unsigned subtract. 'ticket_len - 10 * 4' by prechecking the length of what we're trying to extract in two places in the token and decoding for a response packet. Also use sizeof() on the struct we're extracting rather specifying the size numerically to be consistent with the other related statements.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix OOBs when building SMB2_IOCTL request When using encryption, either enforced by the server or when using 'seal' mount option, the client will squash all compound request buffers down for encryption into a single iov in smb2_set_next_command(). SMB2_ioctl_init() allocates a small buffer (448 bytes) to hold the SMB2_IOCTL request in the first iov, and if the user passes an input buffer that is greater than 328 bytes, smb2_set_next_command() will end up writing off the end of @rqst->iov[0].iov_base as shown below: mount.cifs //srv/share /mnt -o ...,seal ln -s $(perl -e "print('a')for 1..1024") /mnt/link BUG: KASAN: slab-out-of-bounds in smb2_set_next_command.cold+0x1d6/0x24c [cifs] Write of size 4116 at addr ffff8881148fcab8 by task ln/859 CPU: 1 UID: 0 PID: 859 Comm: ln Not tainted 6.12.0-rc3 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-2.fc40 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x5d/0x80 ? smb2_set_next_command.cold+0x1d6/0x24c [cifs] print_report+0x156/0x4d9 ? smb2_set_next_command.cold+0x1d6/0x24c [cifs] ? __virt_addr_valid+0x145/0x310 ? __phys_addr+0x46/0x90 ? smb2_set_next_command.cold+0x1d6/0x24c [cifs] kasan_report+0xda/0x110 ? smb2_set_next_command.cold+0x1d6/0x24c [cifs] kasan_check_range+0x10f/0x1f0 __asan_memcpy+0x3c/0x60 smb2_set_next_command.cold+0x1d6/0x24c [cifs] smb2_compound_op+0x238c/0x3840 [cifs] ? kasan_save_track+0x14/0x30 ? kasan_save_free_info+0x3b/0x70 ? vfs_symlink+0x1a1/0x2c0 ? do_symlinkat+0x108/0x1c0 ? __pfx_smb2_compound_op+0x10/0x10 [cifs] ? kmem_cache_free+0x118/0x3e0 ? cifs_get_writable_path+0xeb/0x1a0 [cifs] smb2_get_reparse_inode+0x423/0x540 [cifs] ? __pfx_smb2_get_reparse_inode+0x10/0x10 [cifs] ? rcu_is_watching+0x20/0x50 ? __kmalloc_noprof+0x37c/0x480 ? smb2_create_reparse_symlink+0x257/0x490 [cifs] ? smb2_create_reparse_symlink+0x38f/0x490 [cifs] smb2_create_reparse_symlink+0x38f/0x490 [cifs] ? __pfx_smb2_create_reparse_symlink+0x10/0x10 [cifs] ? find_held_lock+0x8a/0xa0 ? hlock_class+0x32/0xb0 ? __build_path_from_dentry_optional_prefix+0x19d/0x2e0 [cifs] cifs_symlink+0x24f/0x960 [cifs] ? __pfx_make_vfsuid+0x10/0x10 ? __pfx_cifs_symlink+0x10/0x10 [cifs] ? make_vfsgid+0x6b/0xc0 ? generic_permission+0x96/0x2d0 vfs_symlink+0x1a1/0x2c0 do_symlinkat+0x108/0x1c0 ? __pfx_do_symlinkat+0x10/0x10 ? strncpy_from_user+0xaa/0x160 __x64_sys_symlinkat+0xb9/0xf0 do_syscall_64+0xbb/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f08d75c13bb

In the Linux kernel, the following vulnerability has been resolved: iommu/s390: Fix memory corruption when using identity domain zpci_get_iommu_ctrs() returns counter information to be reported as part of device statistics; these counters are stored as part of the s390_domain. The problem, however, is that the identity domain is not backed by an s390_domain and so the conversion via to_s390_domain() yields a bad address that is zero'd initially and read on-demand later via a sysfs read. These counters aren't necessary for the identity domain; just return NULL in this case. This issue was discovered via KASAN with reports that look like: BUG: KASAN: global-out-of-bounds in zpci_fmb_enable_device when using the identity domain for a device on s390.

In the Linux kernel, the following vulnerability has been resolved: HID: intel-thc-hid: intel-thc: Fix incorrect pointer arithmetic in I2C regs save Improper use of secondary pointer (&dev->i2c_subip_regs) caused kernel crash and out-of-bounds error: BUG: KASAN: slab-out-of-bounds in _regmap_bulk_read+0x449/0x510 Write of size 4 at addr ffff888136005dc0 by task kworker/u33:5/5107 CPU: 3 UID: 0 PID: 5107 Comm: kworker/u33:5 Not tainted 6.16.0+ #3 PREEMPT(voluntary) Workqueue: async async_run_entry_fn Call Trace: <TASK> dump_stack_lvl+0x76/0xa0 print_report+0xd1/0x660 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 ? kasan_complete_mode_report_info+0x26/0x200 kasan_report+0xe1/0x120 ? _regmap_bulk_read+0x449/0x510 ? _regmap_bulk_read+0x449/0x510 __asan_report_store4_noabort+0x17/0x30 _regmap_bulk_read+0x449/0x510 ? __pfx__regmap_bulk_read+0x10/0x10 regmap_bulk_read+0x270/0x3d0 pio_complete+0x1ee/0x2c0 [intel_thc] ? __pfx_pio_complete+0x10/0x10 [intel_thc] ? __pfx_pio_wait+0x10/0x10 [intel_thc] ? regmap_update_bits_base+0x13b/0x1f0 thc_i2c_subip_pio_read+0x117/0x270 [intel_thc] thc_i2c_subip_regs_save+0xc2/0x140 [intel_thc] ? __pfx_thc_i2c_subip_regs_save+0x10/0x10 [intel_thc] [...] The buggy address belongs to the object at ffff888136005d00 which belongs to the cache kmalloc-rnd-12-192 of size 192 The buggy address is located 0 bytes to the right of allocated 192-byte region [ffff888136005d00, ffff888136005dc0) Replaced with direct array indexing (&dev->i2c_subip_regs[i]) to ensure safe memory access.