In the Linux kernel, the following vulnerability has been resolved: ksmbd: prevent out-of-bounds stream writes by validating *pos ksmbd_vfs_stream_write() did not validate whether the write offset (*pos) was within the bounds of the existing stream data length (v_len). If *pos was greater than or equal to v_len, this could lead to an out-of-bounds memory write. This patch adds a check to ensure *pos is less than v_len before proceeding. If the condition fails, -EINVAL is returned.

In the Linux kernel, the following vulnerability has been resolved: md/md-llbitmap: skip reading rdevs that are not in_sync When reading bitmap pages from member disks, the code iterates through all rdevs and attempts to read from the first available one. However, it only checks for raid_disk assignment and Faulty flag, missing the In_sync flag check. This can cause bitmap data to be read from spare disks that are still being rebuilt and don't have valid bitmap information yet. Reading stale or uninitialized bitmap data from such disks can lead to incorrect dirty bit tracking, potentially causing data corruption during recovery or normal operation. Add the In_sync flag check to ensure bitmap pages are only read from fully synchronized member disks that have valid bitmap data.

In the Linux kernel, the following vulnerability has been resolved: crypto: acomp - fix wrong pointer stored by acomp_save_req() acomp_save_req() stores &req->chain in req->base.data. When acomp_reqchain_done() is invoked on asynchronous completion, it receives &req->chain as the data argument but casts it directly to struct acomp_req. Since data points to the chain member, all subsequent field accesses are at a wrong offset, resulting in memory corruption. The issue occurs when an asynchronous hardware implementation, such as the QAT driver, completes a request that uses the DMA virtual address interface (e.g. acomp_request_set_src_dma()). This combination causes crypto_acomp_compress() to enter the acomp_do_req_chain() path, which sets acomp_reqchain_done() as the completion callback via acomp_save_req(). With KASAN enabled, this manifests as a general protection fault in acomp_reqchain_done(): general protection fault, probably for non-canonical address 0xe000040000000000 KASAN: probably user-memory-access in range [0x0000400000000000-0x0000400000000007] RIP: 0010:acomp_reqchain_done+0x15b/0x4e0 Call Trace: <IRQ> qat_comp_alg_callback+0x5d/0xa0 [intel_qat] adf_ring_response_handler+0x376/0x8b0 [intel_qat] adf_response_handler+0x60/0x170 [intel_qat] tasklet_action_common+0x223/0x820 handle_softirqs+0x1ab/0x640 </IRQ> Fix this by storing the request itself in req->base.data instead of &req->chain, so that acomp_reqchain_done() receives the correct pointer. Simplify acomp_restore_req() accordingly to access req->chain directly.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: nbpfaxi: Fix memory corruption in probe() The nbpf->chan[] array is allocated earlier in the nbpf_probe() function and it has "num_channels" elements. These three loops iterate one element farther than they should and corrupt memory. The changes to the second loop are more involved. In this case, we're copying data from the irqbuf[] array into the nbpf->chan[] array. If the data in irqbuf[i] is the error IRQ then we skip it, so the iterators are not in sync. I added a check to ensure that we don't go beyond the end of the irqbuf[] array. I'm pretty sure this can't happen, but it seemed harmless to add a check. On the other hand, after the loop has ended there is a check to ensure that the "chan" iterator is where we expect it to be. In the original code we went one element beyond the end of the array so the iterator wasn't in the correct place and it would always return -EINVAL. However, now it will always be in the correct place. I deleted the check since we know the result.

In the Linux kernel, the following vulnerability has been resolved: drm/nouveau: fix u32 overflow in pushbuf reloc bounds check nouveau_gem_pushbuf_reloc_apply() validates each relocation with if (r->reloc_bo_offset + 4 > nvbo->bo.base.size) but reloc_bo_offset is __u32 (uapi/drm/nouveau_drm.h) and the integer literal 4 promotes to unsigned int, so the addition is performed in 32 bits and wraps before the comparison against the size_t bo size. Cast to u64 so the addition happens in 64-bit arithmetic. [ Add Fixes: tag. - Danilo ]

In the Linux kernel, the following vulnerability has been resolved: RDMA/mana: Validate rx_hash_key_len Sashiko points out that rx_hash_key_len comes from a uAPI structure and is blindly passed to memcpy, allowing the userspace to trash kernel memory. Bounds check it so the memcpy cannot overflow.

In the Linux kernel, the following vulnerability has been resolved: media: vivid: Change the siize of the composing syzkaller found a bug: BUG: KASAN: vmalloc-out-of-bounds in tpg_fill_plane_pattern drivers/media/common/v4l2-tpg/v4l2-tpg-core.c:2608 [inline] BUG: KASAN: vmalloc-out-of-bounds in tpg_fill_plane_buffer+0x1a9c/0x5af0 drivers/media/common/v4l2-tpg/v4l2-tpg-core.c:2705 Write of size 1440 at addr ffffc9000d0ffda0 by task vivid-000-vid-c/5304 CPU: 0 UID: 0 PID: 5304 Comm: vivid-000-vid-c Not tainted 6.14.0-rc2-syzkaller-00039-g09fbf3d50205 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x169/0x550 mm/kasan/report.c:489 kasan_report+0x143/0x180 mm/kasan/report.c:602 kasan_check_range+0x282/0x290 mm/kasan/generic.c:189 __asan_memcpy+0x40/0x70 mm/kasan/shadow.c:106 tpg_fill_plane_pattern drivers/media/common/v4l2-tpg/v4l2-tpg-core.c:2608 [inline] tpg_fill_plane_buffer+0x1a9c/0x5af0 drivers/media/common/v4l2-tpg/v4l2-tpg-core.c:2705 vivid_fillbuff drivers/media/test-drivers/vivid/vivid-kthread-cap.c:470 [inline] vivid_thread_vid_cap_tick+0xf8e/0x60d0 drivers/media/test-drivers/vivid/vivid-kthread-cap.c:629 vivid_thread_vid_cap+0x8aa/0xf30 drivers/media/test-drivers/vivid/vivid-kthread-cap.c:767 kthread+0x7a9/0x920 kernel/kthread.c:464 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 </TASK> The composition size cannot be larger than the size of fmt_cap_rect. So execute v4l2_rect_map_inside() even if has_compose_cap == 0.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k_htc: Abort software beacon handling if disabled A malicious USB device can send a WMI_SWBA_EVENTID event from an ath9k_htc-managed device before beaconing has been enabled. This causes a device-by-zero error in the driver, leading to either a crash or an out of bounds read. Prevent this by aborting the handling in ath9k_htc_swba() if beacons are not enabled.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix max_sge overflow in smb_extract_folioq_to_rdma() This fixes the following problem: [ 749.901015] [ T8673] run fstests cifs/001 at 2025-06-17 09:40:30 [ 750.346409] [ T9870] ================================================================== [ 750.346814] [ T9870] BUG: KASAN: slab-out-of-bounds in smb_set_sge+0x2cc/0x3b0 [cifs] [ 750.347330] [ T9870] Write of size 8 at addr ffff888011082890 by task xfs_io/9870 [ 750.347705] [ T9870] [ 750.348077] [ T9870] CPU: 0 UID: 0 PID: 9870 Comm: xfs_io Kdump: loaded Not tainted 6.16.0-rc2-metze.02+ #1 PREEMPT(voluntary) [ 750.348082] [ T9870] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 750.348085] [ T9870] Call Trace: [ 750.348086] [ T9870] <TASK> [ 750.348088] [ T9870] dump_stack_lvl+0x76/0xa0 [ 750.348106] [ T9870] print_report+0xd1/0x640 [ 750.348116] [ T9870] ? __pfx__raw_spin_lock_irqsave+0x10/0x10 [ 750.348120] [ T9870] ? kasan_complete_mode_report_info+0x26/0x210 [ 750.348124] [ T9870] kasan_report+0xe7/0x130 [ 750.348128] [ T9870] ? smb_set_sge+0x2cc/0x3b0 [cifs] [ 750.348262] [ T9870] ? smb_set_sge+0x2cc/0x3b0 [cifs] [ 750.348377] [ T9870] __asan_report_store8_noabort+0x17/0x30 [ 750.348381] [ T9870] smb_set_sge+0x2cc/0x3b0 [cifs] [ 750.348496] [ T9870] smbd_post_send_iter+0x1990/0x3070 [cifs] [ 750.348625] [ T9870] ? __pfx_smbd_post_send_iter+0x10/0x10 [cifs] [ 750.348741] [ T9870] ? update_stack_state+0x2a0/0x670 [ 750.348749] [ T9870] ? cifs_flush+0x153/0x320 [cifs] [ 750.348870] [ T9870] ? cifs_flush+0x153/0x320 [cifs] [ 750.348990] [ T9870] ? update_stack_state+0x2a0/0x670 [ 750.348995] [ T9870] smbd_send+0x58c/0x9c0 [cifs] [ 750.349117] [ T9870] ? __pfx_smbd_send+0x10/0x10 [cifs] [ 750.349231] [ T9870] ? unwind_get_return_address+0x65/0xb0 [ 750.349235] [ T9870] ? __pfx_stack_trace_consume_entry+0x10/0x10 [ 750.349242] [ T9870] ? arch_stack_walk+0xa7/0x100 [ 750.349250] [ T9870] ? stack_trace_save+0x92/0xd0 [ 750.349254] [ T9870] __smb_send_rqst+0x931/0xec0 [cifs] [ 750.349374] [ T9870] ? kernel_text_address+0x173/0x190 [ 750.349379] [ T9870] ? kasan_save_stack+0x39/0x70 [ 750.349382] [ T9870] ? kasan_save_track+0x18/0x70 [ 750.349385] [ T9870] ? __kasan_slab_alloc+0x9d/0xa0 [ 750.349389] [ T9870] ? __pfx___smb_send_rqst+0x10/0x10 [cifs] [ 750.349508] [ T9870] ? smb2_mid_entry_alloc+0xb4/0x7e0 [cifs] [ 750.349626] [ T9870] ? cifs_call_async+0x277/0xb00 [cifs] [ 750.349746] [ T9870] ? cifs_issue_write+0x256/0x610 [cifs] [ 750.349867] [ T9870] ? netfs_do_issue_write+0xc2/0x340 [netfs] [ 750.349900] [ T9870] ? netfs_advance_write+0x45b/0x1270 [netfs] [ 750.349929] [ T9870] ? netfs_write_folio+0xd6c/0x1be0 [netfs] [ 750.349958] [ T9870] ? netfs_writepages+0x2e9/0xa80 [netfs] [ 750.349987] [ T9870] ? do_writepages+0x21f/0x590 [ 750.349993] [ T9870] ? filemap_fdatawrite_wbc+0xe1/0x140 [ 750.349997] [ T9870] ? entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 750.350002] [ T9870] smb_send_rqst+0x22e/0x2f0 [cifs] [ 750.350131] [ T9870] ? __pfx_smb_send_rqst+0x10/0x10 [cifs] [ 750.350255] [ T9870] ? local_clock_noinstr+0xe/0xd0 [ 750.350261] [ T9870] ? kasan_save_alloc_info+0x37/0x60 [ 750.350268] [ T9870] ? __kasan_check_write+0x14/0x30 [ 750.350271] [ T9870] ? _raw_spin_lock+0x81/0xf0 [ 750.350275] [ T9870] ? __pfx__raw_spin_lock+0x10/0x10 [ 750.350278] [ T9870] ? smb2_setup_async_request+0x293/0x580 [cifs] [ 750.350398] [ T9870] cifs_call_async+0x477/0xb00 [cifs] [ 750.350518] [ T9870] ? __pfx_smb2_writev_callback+0x10/0x10 [cifs] [ 750.350636] [ T9870] ? __pfx_cifs_call_async+0x10/0x10 [cifs] [ 750.350756] [ T9870] ? __pfx__raw_spin_lock+0x10/0x10 [ 750.350760] [ T9870] ? __kasan_check_write+0x14/0x30 [ 750.350763] [ T98 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: iio: backend: fix out-of-bound write The buffer is set to 80 character. If a caller write more characters, count is truncated to the max available space in "simple_write_to_buffer". But afterwards a string terminator is written to the buffer at offset count without boundary check. The zero termination is written OUT-OF-BOUND. Add a check that the given buffer is smaller then the buffer to prevent.

In the Linux Kernel before versions 4.20.8 and 4.19.21 a use-after-free error in the "sctp_sendmsg()" function (net/sctp/socket.c) when handling SCTP_SENDALL flag can be exploited to corrupt memory.

In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: Check to ensure report responses match the request It is possible for a malicious (or clumsy) device to respond to a specific report's feature request using a completely different report ID. This can cause confusion in the HID core resulting in nasty side-effects such as OOB writes. Add a check to ensure that the report ID in the response, matches the one that was requested. If it doesn't, omit reporting the raw event and return early.

In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - Fix page reassignment overflow in af_alg_pull_tsgl When page reassignment was added to af_alg_pull_tsgl the original loop wasn't updated so it may try to reassign one more page than necessary. Add the check to the reassignment so that this does not happen. Also update the comment which still refers to the obsolete offset argument.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix out-of-bounds write in ocfs2_write_end_inline KASAN reports a use-after-free write of 4086 bytes in ocfs2_write_end_inline, called from ocfs2_write_end_nolock during a copy_file_range splice fallback on a corrupted ocfs2 filesystem mounted on a loop device. The actual bug is an out-of-bounds write past the inode block buffer, not a true use-after-free. The write overflows into an adjacent freed page, which KASAN reports as UAF. The root cause is that ocfs2_try_to_write_inline_data trusts the on-disk id_count field to determine whether a write fits in inline data. On a corrupted filesystem, id_count can exceed the physical maximum inline data capacity, causing writes to overflow the inode block buffer. Call trace (crash path): vfs_copy_file_range (fs/read_write.c:1634) do_splice_direct splice_direct_to_actor iter_file_splice_write ocfs2_file_write_iter generic_perform_write ocfs2_write_end ocfs2_write_end_nolock (fs/ocfs2/aops.c:1949) ocfs2_write_end_inline (fs/ocfs2/aops.c:1915) memcpy_from_folio <-- KASAN: write OOB So add id_count upper bound check in ocfs2_validate_inode_block() to alongside the existing i_size check to fix it.

In the Linux kernel, the following vulnerability has been resolved: perf/arm-cmn: Reject unsupported hardware configurations So far we've been fairly lax about accepting both unknown CMN models (at least with a warning), and unknown revisions of those which we do know, as although things do frequently change between releases, typically enough remains the same to be somewhat useful for at least some basic bringup checks. However, we also make assumptions of the maximum supported sizes and numbers of things in various places, and there's no guarantee that something new might not be bigger and lead to nasty array overflows. Make sure we only try to run on things that actually match our assumptions and so will not risk memory corruption. We have at least always failed on completely unknown node types, so update that error message for clarity and consistency too.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Add sanity check for OOB writes at silencing At silencing the playback URB packets in the implicit fb mode before the actual playback, we blindly assume that the received packets fit with the buffer size. But when the setup in the capture stream differs from the playback stream (e.g. due to the USB core limitation of max packet size), such an inconsistency may lead to OOB writes to the buffer, resulting in a crash. For addressing it, add a sanity check of the transfer buffer size at prepare_silent_urb(), and stop the data copy if the received data overflows. Also, report back the transfer error properly from there, too. Note that this doesn't fix the root cause of the playback error itself, but this merely covers the kernel Oops.

In the Linux kernel, the following vulnerability has been resolved: crypto: caam - fix overflow on long hmac keys When a key longer than block size is supplied, it is copied and then hashed into the real key. The memory allocated for the copy needs to be rounded to DMA cache alignment, as otherwise the hashed key may corrupt neighbouring memory. The copying is performed using kmemdup, however this leads to an overflow: reading more bytes (aligned_len - keylen) from the keylen source buffer. Fix this by replacing kmemdup with kmalloc, followed by memcpy.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: MGMT: validate LTK enc_size on load Load Long Term Keys stores the user-provided enc_size and later uses it to size fixed-size stack operations when replying to LE LTK requests. An enc_size larger than the 16-byte key buffer can therefore overflow the reply stack buffer. Reject oversized enc_size values while validating the management LTK record so invalid keys never reach the stored key state.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix error handling in ext4_fc_record_modified_inode() Current code does not fully takes care of krealloc() error case, which could lead to silent memory corruption or a kernel bug. This patch fixes that. Also it cleans up some duplicated error handling logic from various functions in fast_commit.c file.

In the Linux kernel, the following vulnerability has been resolved: dpaa2-switch: validate num_ifs to prevent out-of-bounds write The driver obtains sw_attr.num_ifs from firmware via dpsw_get_attributes() but never validates it against DPSW_MAX_IF (64). This value controls iteration in dpaa2_switch_fdb_get_flood_cfg(), which writes port indices into the fixed-size cfg->if_id[DPSW_MAX_IF] array. When firmware reports num_ifs >= 64, the loop can write past the array bounds. Add a bound check for num_ifs in dpaa2_switch_init(). dpaa2_switch_fdb_get_flood_cfg() appends the control interface (port num_ifs) after all matched ports. When num_ifs == DPSW_MAX_IF and all ports match the flood filter, the loop fills all 64 slots and the control interface write overflows by one entry. The check uses >= because num_ifs == DPSW_MAX_IF is also functionally broken. build_if_id_bitmap() silently drops any ID >= 64: if (id[i] < DPSW_MAX_IF) bmap[id[i] / 64] |= ...

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Also unshare DATA/RESPONSE packets when paged frags are present The DATA-packet handler in rxrpc_input_call_event() and the RESPONSE handler in rxrpc_verify_response() copy the skb to a linear one before calling into the security ops only when skb_cloned() is true. An skb that is not cloned but still carries externally-owned paged fragments (e.g. SKBFL_SHARED_FRAG set by splice() into a UDP socket via __ip_append_data, or a chained skb_has_frag_list()) falls through to the in-place decryption path, which binds the frag pages directly into the AEAD/skcipher SGL via skb_to_sgvec(). Extend the gate to also unshare when skb_has_frag_list() or skb_has_shared_frag() is true. This catches the splice-loopback vector and other externally-shared frag sources while preserving the zero-copy fast path for skbs whose frags are kernel-private (e.g. NIC page_pool RX, GRO). The OOM/trace handling already in place is reused.

In the Linux kernel, the following vulnerability has been resolved: vhost: move vdpa group bound check to vhost_vdpa Remove duplication by consolidating these here. This reduces the posibility of a parent driver missing them. While we're at it, fix a bug in vdpa_sim where a valid ASID can be assigned to a group equal to ngroups, causing an out of bound write.

In the Linux kernel, the following vulnerability has been resolved: netfs: Fix unbuffered write error handling If all the subrequests in an unbuffered write stream fail, the subrequest collector doesn't update the stream->transferred value and it retains its initial LONG_MAX value. Unfortunately, if all active streams fail, then we take the smallest value of { LONG_MAX, LONG_MAX, ... } as the value to set in wreq->transferred - which is then returned from ->write_iter(). LONG_MAX was chosen as the initial value so that all the streams can be quickly assessed by taking the smallest value of all stream->transferred - but this only works if we've set any of them. Fix this by adding a flag to indicate whether the value in stream->transferred is valid and checking that when we integrate the values. stream->transferred can then be initialised to zero. This was found by running the generic/750 xfstest against cifs with cache=none. It splices data to the target file. Once (if) it has used up all the available scratch space, the writes start failing with ENOSPC. This causes ->write_iter() to fail. However, it was returning wreq->transferred, i.e. LONG_MAX, rather than an error (because it thought the amount transferred was non-zero) and iter_file_splice_write() would then try to clean up that amount of pipe bufferage - leading to an oops when it overran. The kernel log showed: CIFS: VFS: Send error in write = -28 followed by: BUG: kernel NULL pointer dereference, address: 0000000000000008 with: RIP: 0010:iter_file_splice_write+0x3a4/0x520 do_splice+0x197/0x4e0 or: RIP: 0010:pipe_buf_release (include/linux/pipe_fs_i.h:282) iter_file_splice_write (fs/splice.c:755) Also put a warning check into splice to announce if ->write_iter() returned that it had written more than it was asked to.

In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: avoid buffer overflow in WID string configuration Fix the following copy overflow warning identified by Smatch checker. drivers/net/wireless/microchip/wilc1000/wlan_cfg.c:184 wilc_wlan_parse_response_frame() error: '__memcpy()' 'cfg->s[i]->str' copy overflow (512 vs 65537) This patch introduces size check before accessing the memory buffer. The checks are base on the WID type of received data from the firmware. For WID string configuration, the size limit is determined by individual element size in 'struct wilc_cfg_str_vals' that is maintained in 'len' field of 'struct wilc_cfg_str'.

In the Linux kernel, the following vulnerability has been resolved: iavf: fix out-of-bounds writes in iavf_get_ethtool_stats() iavf incorrectly uses real_num_tx_queues for ETH_SS_STATS. Since the value could change in runtime, we should use num_tx_queues instead. Moreover iavf_get_ethtool_stats() uses num_active_queues while iavf_get_sset_count() and iavf_get_stat_strings() use real_num_tx_queues, which triggers out-of-bounds writes when we do "ethtool -L" and "ethtool -S" simultaneously [1]. For example when we change channels from 1 to 8, Thread 3 could be scheduled before Thread 2, and out-of-bounds writes could be triggered in Thread 3: Thread 1 (ethtool -L) Thread 2 (work) Thread 3 (ethtool -S) iavf_set_channels() ... iavf_alloc_queues() -> num_active_queues = 8 iavf_schedule_finish_config() iavf_get_sset_count() real_num_tx_queues: 1 -> buffer for 1 queue iavf_get_ethtool_stats() num_active_queues: 8 -> out-of-bounds! iavf_finish_config() -> real_num_tx_queues = 8 Use immutable num_tx_queues in all related functions to avoid the issue. [1] BUG: KASAN: vmalloc-out-of-bounds in iavf_add_one_ethtool_stat+0x200/0x270 Write of size 8 at addr ffffc900031c9080 by task ethtool/5800 CPU: 1 UID: 0 PID: 5800 Comm: ethtool Not tainted 6.19.0-enjuk-08403-g8137e3db7f1c #241 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x6f/0xb0 print_report+0x170/0x4f3 kasan_report+0xe1/0x180 iavf_add_one_ethtool_stat+0x200/0x270 iavf_get_ethtool_stats+0x14c/0x2e0 __dev_ethtool+0x3d0c/0x5830 dev_ethtool+0x12d/0x270 dev_ioctl+0x53c/0xe30 sock_do_ioctl+0x1a9/0x270 sock_ioctl+0x3d4/0x5e0 __x64_sys_ioctl+0x137/0x1c0 do_syscall_64+0xf3/0x690 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f7da0e6e36d ... </TASK> The buggy address belongs to a 1-page vmalloc region starting at 0xffffc900031c9000 allocated at __dev_ethtool+0x3cc9/0x5830 The buggy address belongs to the physical page: page: refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88813a013de0 pfn:0x13a013 flags: 0x200000000000000(node=0|zone=2) raw: 0200000000000000 0000000000000000 dead000000000122 0000000000000000 raw: ffff88813a013de0 0000000000000000 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffffc900031c8f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc900031c9000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffffc900031c9080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ^ ffffc900031c9100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc900031c9180: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix undefined behavior in interpreter sdiv/smod for INT_MIN The BPF interpreter's signed 32-bit division and modulo handlers use the kernel abs() macro on s32 operands. The abs() macro documentation (include/linux/math.h) explicitly states the result is undefined when the input is the type minimum. When DST contains S32_MIN (0x80000000), abs((s32)DST) triggers undefined behavior and returns S32_MIN unchanged on arm64/x86. This value is then sign-extended to u64 as 0xFFFFFFFF80000000, causing do_div() to compute the wrong result. The verifier's abstract interpretation (scalar32_min_max_sdiv) computes the mathematically correct result for range tracking, creating a verifier/interpreter mismatch that can be exploited for out-of-bounds map value access. Introduce abs_s32() which handles S32_MIN correctly by casting to u32 before negating, avoiding signed overflow entirely. Replace all 8 abs((s32)...) call sites in the interpreter's sdiv32/smod32 handlers. s32 is the only affected case -- the s64 division/modulo handlers do not use abs().

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Validate UAC3 power domain descriptors, too UAC3 power domain descriptors need to be verified with its variable bLength for avoiding the unexpected OOB accesses by malicious firmware, too.

In the Linux kernel, the following vulnerability has been resolved: firmware: thead: Fix buffer overflow and use standard endian macros Addresses two issues in the TH1520 AON firmware protocol driver: 1. Fix a potential buffer overflow where the code used unsafe pointer arithmetic to access the 'mode' field through the 'resource' pointer with an offset. This was flagged by Smatch static checker as: "buffer overflow 'data' 2 <= 3" 2. Replace custom RPC_SET_BE* and RPC_GET_BE* macros with standard kernel endianness conversion macros (cpu_to_be16, etc.) for better portability and maintainability. The functionality was re-tested with the GPU power-up sequence, confirming the GPU powers up correctly and the driver probes successfully. [ 12.702370] powervr ffef400000.gpu: [drm] loaded firmware powervr/rogue_36.52.104.182_v1.fw [ 12.711043] powervr ffef400000.gpu: [drm] FW version v1.0 (build 6645434 OS) [ 12.719787] [drm] Initialized powervr 1.0.0 for ffef400000.gpu on minor 0

In the Linux kernel, the following vulnerability has been resolved: net: macb: use the current queue number for stats There's a potential mismatch between the memory reserved for statistics and the amount of memory written. gem_get_sset_count() correctly computes the number of stats based on the active queues, whereas gem_get_ethtool_stats() indiscriminately copies data using the maximum number of queues, and in the case the number of active queues is less than MACB_MAX_QUEUES, this results in a OOB write as observed in the KASAN splat. ================================================================== BUG: KASAN: vmalloc-out-of-bounds in gem_get_ethtool_stats+0x54/0x78 [macb] Write of size 760 at addr ffff80008080b000 by task ethtool/1027 CPU: [...] Tainted: [E]=UNSIGNED_MODULE Hardware name: raspberrypi rpi/rpi, BIOS 2025.10 10/01/2025 Call trace: show_stack+0x20/0x38 (C) dump_stack_lvl+0x80/0xf8 print_report+0x384/0x5e0 kasan_report+0xa0/0xf0 kasan_check_range+0xe8/0x190 __asan_memcpy+0x54/0x98 gem_get_ethtool_stats+0x54/0x78 [macb 926c13f3af83b0c6fe64badb21ec87d5e93fcf65] dev_ethtool+0x1220/0x38c0 dev_ioctl+0x4ac/0xca8 sock_do_ioctl+0x170/0x1d8 sock_ioctl+0x484/0x5d8 __arm64_sys_ioctl+0x12c/0x1b8 invoke_syscall+0xd4/0x258 el0_svc_common.constprop.0+0xb4/0x240 do_el0_svc+0x48/0x68 el0_svc+0x40/0xf8 el0t_64_sync_handler+0xa0/0xe8 el0t_64_sync+0x1b0/0x1b8 The buggy address belongs to a 1-page vmalloc region starting at 0xffff80008080b000 allocated at dev_ethtool+0x11f0/0x38c0 The buggy address belongs to the physical page: page: refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff00000a333000 pfn:0xa333 flags: 0x7fffc000000000(node=0|zone=0|lastcpupid=0x1ffff) raw: 007fffc000000000 0000000000000000 dead000000000122 0000000000000000 raw: ffff00000a333000 0000000000000000 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff80008080b080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff80008080b100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff80008080b180: 00 00 00 00 00 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ^ ffff80008080b200: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffff80008080b280: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ================================================================== Fix it by making sure the copied size only considers the active number of queues.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_uac1_legacy: validate control request size f_audio_complete() copies req->length bytes into a 4-byte stack variable: u32 data = 0; memcpy(&data, req->buf, req->length); req->length is derived from the host-controlled USB request path, which can lead to a stack out-of-bounds write. Validate req->actual against the expected payload size for the supported control selectors and decode only the expected amount of data. This avoids copying a host-influenced length into a fixed-size stack object.

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix heap overflow in NFSv4.0 LOCK replay cache The NFSv4.0 replay cache uses a fixed 112-byte inline buffer (rp_ibuf[NFSD4_REPLAY_ISIZE]) to store encoded operation responses. This size was calculated based on OPEN responses and does not account for LOCK denied responses, which include the conflicting lock owner as a variable-length field up to 1024 bytes (NFS4_OPAQUE_LIMIT). When a LOCK operation is denied due to a conflict with an existing lock that has a large owner, nfsd4_encode_operation() copies the full encoded response into the undersized replay buffer via read_bytes_from_xdr_buf() with no bounds check. This results in a slab-out-of-bounds write of up to 944 bytes past the end of the buffer, corrupting adjacent heap memory. This can be triggered remotely by an unauthenticated attacker with two cooperating NFSv4.0 clients: one sets a lock with a large owner string, then the other requests a conflicting lock to provoke the denial. We could fix this by increasing NFSD4_REPLAY_ISIZE to allow for a full opaque, but that would increase the size of every stateowner, when most lockowners are not that large. Instead, fix this by checking the encoded response length against NFSD4_REPLAY_ISIZE before copying into the replay buffer. If the response is too large, set rp_buflen to 0 to skip caching the replay payload. The status is still cached, and the client already received the correct response on the original request.

In the Linux kernel, the following vulnerability has been resolved: platform/x86: asus-wmi: Fix racy registrations asus_wmi_register_driver() may be called from multiple drivers concurrently, which can lead to the racy list operations, eventually corrupting the memory and hitting Oops on some ASUS machines. Also, the error handling is missing, and it forgot to unregister ACPI lps0 dev ops in the error case. This patch covers those issues by introducing a simple mutex at acpi_wmi_register_driver() & *_unregister_driver, and adding the proper call of asus_s2idle_check_unregister() in the error path.

In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: mt8365-dai-i2s: pass correct size to mt8365_dai_set_priv Given mt8365_dai_set_priv allocate priv_size space to copy priv_data which means we should pass mt8365_i2s_priv[i] or "struct mtk_afe_i2s_priv" instead of afe_priv which has the size of "struct mt8365_afe_private". Otherwise the KASAN complains about. [ 59.389765] BUG: KASAN: global-out-of-bounds in mt8365_dai_set_priv+0xc8/0x168 [snd_soc_mt8365_pcm] ... [ 59.394789] Call trace: [ 59.395167] dump_backtrace+0xa0/0x128 [ 59.395733] show_stack+0x20/0x38 [ 59.396238] dump_stack_lvl+0xe8/0x148 [ 59.396806] print_report+0x37c/0x5e0 [ 59.397358] kasan_report+0xac/0xf8 [ 59.397885] kasan_check_range+0xe8/0x190 [ 59.398485] asan_memcpy+0x3c/0x98 [ 59.399022] mt8365_dai_set_priv+0xc8/0x168 [snd_soc_mt8365_pcm] [ 59.399928] mt8365_dai_i2s_register+0x1e8/0x2b0 [snd_soc_mt8365_pcm] [ 59.400893] mt8365_afe_pcm_dev_probe+0x4d0/0xdf0 [snd_soc_mt8365_pcm] [ 59.401873] platform_probe+0xcc/0x228 [ 59.402442] really_probe+0x340/0x9e8 [ 59.402992] driver_probe_device+0x16c/0x3f8 [ 59.403638] driver_probe_device+0x64/0x1d8 [ 59.404256] driver_attach+0x1dc/0x4c8 [ 59.404840] bus_for_each_dev+0x100/0x190 [ 59.405442] driver_attach+0x44/0x68 [ 59.405980] bus_add_driver+0x23c/0x500 [ 59.406550] driver_register+0xf8/0x3d0 [ 59.407122] platform_driver_register+0x68/0x98 [ 59.407810] mt8365_afe_pcm_driver_init+0x2c/0xff8 [snd_soc_mt8365_pcm]

In the Linux kernel, the following vulnerability has been resolved: HID: intel-thc-hid: intel-thc: Fix incorrect pointer arithmetic in I2C regs save Improper use of secondary pointer (&dev->i2c_subip_regs) caused kernel crash and out-of-bounds error: BUG: KASAN: slab-out-of-bounds in _regmap_bulk_read+0x449/0x510 Write of size 4 at addr ffff888136005dc0 by task kworker/u33:5/5107 CPU: 3 UID: 0 PID: 5107 Comm: kworker/u33:5 Not tainted 6.16.0+ #3 PREEMPT(voluntary) Workqueue: async async_run_entry_fn Call Trace: <TASK> dump_stack_lvl+0x76/0xa0 print_report+0xd1/0x660 ? __pfx__raw_spin_lock_irqsave+0x10/0x10 ? kasan_complete_mode_report_info+0x26/0x200 kasan_report+0xe1/0x120 ? _regmap_bulk_read+0x449/0x510 ? _regmap_bulk_read+0x449/0x510 __asan_report_store4_noabort+0x17/0x30 _regmap_bulk_read+0x449/0x510 ? __pfx__regmap_bulk_read+0x10/0x10 regmap_bulk_read+0x270/0x3d0 pio_complete+0x1ee/0x2c0 [intel_thc] ? __pfx_pio_complete+0x10/0x10 [intel_thc] ? __pfx_pio_wait+0x10/0x10 [intel_thc] ? regmap_update_bits_base+0x13b/0x1f0 thc_i2c_subip_pio_read+0x117/0x270 [intel_thc] thc_i2c_subip_regs_save+0xc2/0x140 [intel_thc] ? __pfx_thc_i2c_subip_regs_save+0x10/0x10 [intel_thc] [...] The buggy address belongs to the object at ffff888136005d00 which belongs to the cache kmalloc-rnd-12-192 of size 192 The buggy address is located 0 bytes to the right of allocated 192-byte region [ffff888136005d00, ffff888136005dc0) Replaced with direct array indexing (&dev->i2c_subip_regs[i]) to ensure safe memory access.

In the Linux kernel, the following vulnerability has been resolved: Buffer overflow in drivers/xen/sys-hypervisor.c The build id returned by HYPERVISOR_xen_version(XENVER_build_id) is neither NUL terminated nor a string. The first causes a buffer overflow as sprintf in buildid_show will read and copy till it finds a NUL. 00000000 f4 91 51 f4 dd 38 9e 9d 65 47 52 eb 10 71 db 50 |..Q..8..eGR..q.P| 00000010 b9 a8 01 42 6f 2e 32 |...Bo.2| 00000017 So use a memcpy instead of sprintf to have the correct value: 00000000 f4 91 51 f4 dd 00 9e 9d 65 47 52 eb 10 71 db 50 |..Q.....eGR..q.P| 00000010 b9 a8 01 42 |...B| 00000014 (the above have a hack to embed a zero inside and check it's returned correctly). This is XSA-485 / CVE-2026-31786

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix missing validation of ticket length in non-XDR key preparsing In rxrpc_preparse(), there are two paths for parsing key payloads: the XDR path (for large payloads) and the non-XDR path (for payloads <= 28 bytes). While the XDR path (rxrpc_preparse_xdr_rxkad()) correctly validates the ticket length against AFSTOKEN_RK_TIX_MAX, the non-XDR path fails to do so. This allows an unprivileged user to provide a very large ticket length. When this key is later read via rxrpc_read(), the total token size (toksize) calculation results in a value that exceeds AFSTOKEN_LENGTH_MAX, triggering a WARN_ON(). [ 2001.302904] WARNING: CPU: 2 PID: 2108 at net/rxrpc/key.c:778 rxrpc_read+0x109/0x5c0 [rxrpc] Fix this by adding a check in the non-XDR parsing path of rxrpc_preparse() to ensure the ticket length does not exceed AFSTOKEN_RK_TIX_MAX, bringing it into parity with the XDR parsing logic.

In the Linux kernel, the following vulnerability has been resolved: ASoC: codec: sma1307: Fix memory corruption in sma1307_setting_loaded() The sma1307->set.header_size is how many integers are in the header (there are 8 of them) but instead of allocating space of 8 integers we allocate 8 bytes. This leads to memory corruption when we copy data it on the next line: memcpy(sma1307->set.header, data, sma1307->set.header_size * sizeof(int)); Also since we're immediately copying over the memory in ->set.header, there is no need to zero it in the allocator. Use devm_kmalloc_array() to allocate the memory instead.

In the Linux kernel, the following vulnerability has been resolved: ext4: convert inline data to extents when truncate exceeds inline size Add a check in ext4_setattr() to convert files from inline data storage to extent-based storage when truncate() grows the file size beyond the inline capacity. This prevents the filesystem from entering an inconsistent state where the inline data flag is set but the file size exceeds what can be stored inline. Without this fix, the following sequence causes a kernel BUG_ON(): 1. Mount filesystem with inode that has inline flag set and small size 2. truncate(file, 50MB) - grows size but inline flag remains set 3. sendfile() attempts to write data 4. ext4_write_inline_data() hits BUG_ON(write_size > inline_capacity) The crash occurs because ext4_write_inline_data() expects inline storage to accommodate the write, but the actual inline capacity (~60 bytes for i_block + ~96 bytes for xattrs) is far smaller than the file size and write request. The fix checks if the new size from setattr exceeds the inode's actual inline capacity (EXT4_I(inode)->i_inline_size) and converts the file to extent-based storage before proceeding with the size change. This addresses the root cause by ensuring the inline data flag and file size remain consistent during truncate operations.

In the Linux kernel, the following vulnerability has been resolved: sctp: fix OOB write to userspace in sctp_getsockopt_peer_auth_chunks sctp_getsockopt_peer_auth_chunks() checks that the caller's optval buffer is large enough for the peer AUTH chunk list with if (len < num_chunks) return -EINVAL; but then writes num_chunks bytes to p->gauth_chunks, which lives at offset offsetof(struct sctp_authchunks, gauth_chunks) == 8 inside optval. The check is missing the sizeof(struct sctp_authchunks) = 8-byte header. When the caller supplies len == num_chunks (for any num_chunks > 0) the test passes but copy_to_user() writes sizeof(struct sctp_authchunks) = 8 bytes past the declared buffer. The sibling function sctp_getsockopt_local_auth_chunks() at the next line already has the correct check: if (len < sizeof(struct sctp_authchunks) + num_chunks) return -EINVAL; Align the peer variant with its sibling. Reproducer confirms on v7.0-13-generic: an unprivileged userspace caller that opens a loopback SCTP association with AUTH enabled, queries num_chunks with a short optval, then issues the real getsockopt with len == num_chunks and sentinel bytes painted past the buffer observes those sentinel bytes overwritten with the peer's AUTH chunk type. The bytes written are under the peer's control but land in the caller's own userspace; this is not a kernel memory corruption, but it is a kernel-side contract violation that can silently corrupt adjacent userspace data.

An issue was discovered in yurex_read in drivers/usb/misc/yurex.c in the Linux kernel before 4.17.7. Local attackers could use user access read/writes with incorrect bounds checking in the yurex USB driver to crash the kernel or potentially escalate privileges.

In the Linux kernel, the following vulnerability has been resolved: HID: appletb-kbd: fix memory corruption of input_handler_list In appletb_kbd_probe an input handler is initialised and then registered with input core through input_register_handler(). When this happens input core will add the input handler (specifically its node) to the global input_handler_list. The input_handler_list is central to the functionality of input core and is traversed in various places in input core. An example of this is when a new input device is plugged in and gets registered with input core. The input_handler in probe is allocated as device managed memory. If a probe failure occurs after input_register_handler() the input_handler memory is freed, yet it will remain in the input_handler_list. This effectively means the input_handler_list contains a dangling pointer to data belonging to a freed input handler. This causes an issue when any other input device is plugged in - in my case I had an old PixArt HP USB optical mouse and I decided to plug it in after a failure occurred after input_register_handler(). This lead to the registration of this input device via input_register_device which involves traversing over every handler in the corrupted input_handler_list and calling input_attach_handler(), giving each handler a chance to bind to newly registered device. The core of this bug is a UAF which causes memory corruption of input_handler_list and to fix it we must ensure the input handler is unregistered from input core, this is done through input_unregister_handler(). [ 63.191597] ================================================================== [ 63.192094] BUG: KASAN: slab-use-after-free in input_attach_handler.isra.0+0x1a9/0x1e0 [ 63.192094] Read of size 8 at addr ffff888105ea7c80 by task kworker/0:2/54 [ 63.192094] [ 63.192094] CPU: 0 UID: 0 PID: 54 Comm: kworker/0:2 Not tainted 6.16.0-rc2-00321-g2aa6621d [ 63.192094] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.164 [ 63.192094] Workqueue: usb_hub_wq hub_event [ 63.192094] Call Trace: [ 63.192094] <TASK> [ 63.192094] dump_stack_lvl+0x53/0x70 [ 63.192094] print_report+0xce/0x670 [ 63.192094] kasan_report+0xce/0x100 [ 63.192094] input_attach_handler.isra.0+0x1a9/0x1e0 [ 63.192094] input_register_device+0x76c/0xd00 [ 63.192094] hidinput_connect+0x686d/0xad60 [ 63.192094] hid_connect+0xf20/0x1b10 [ 63.192094] hid_hw_start+0x83/0x100 [ 63.192094] hid_device_probe+0x2d1/0x680 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] hid_add_device+0x30b/0x910 [ 63.192094] usbhid_probe+0x920/0xe00 [ 63.192094] usb_probe_interface+0x363/0x9a0 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] usb_set_configuration+0xd14/0x1880 [ 63.192094] usb_generic_driver_probe+0x78/0xb0 [ 63.192094] usb_probe_device+0xaa/0x2e0 [ 63.192094] really_probe+0x1c3/0x690 [ 63.192094] __driver_probe_device+0x247/0x300 [ 63.192094] driver_probe_device+0x49/0x210 [ 63.192094] __device_attach_driver+0x160/0x320 [ 63.192094] bus_for_each_drv+0x10f/0x190 [ 63.192094] __device_attach+0x18e/0x370 [ 63.192094] bus_probe_device+0x123/0x170 [ 63.192094] device_add+0xd4d/0x1460 [ 63.192094] usb_new_device+0x7b4/0x1000 [ 63.192094] hub_event+0x234d/0x3 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Fix invalid entry fetch in ath12k_dp_mon_srng_process Currently, ath12k_dp_mon_srng_process uses ath12k_hal_srng_src_get_next_entry to fetch the next entry from the destination ring. This is incorrect because ath12k_hal_srng_src_get_next_entry is intended for source rings, not destination rings. This leads to invalid entry fetches, causing potential data corruption or crashes due to accessing incorrect memory locations. This happens because the source ring and destination ring have different handling mechanisms and using the wrong function results in incorrect pointer arithmetic and ring management. To fix this issue, replace the call to ath12k_hal_srng_src_get_next_entry with ath12k_hal_srng_dst_get_next_entry in ath12k_dp_mon_srng_process. This ensures that the correct function is used for fetching entries from the destination ring, preventing invalid memory accesses. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

In the Linux kernel, the following vulnerability has been resolved: staging: media: atomisp: Fix stack buffer overflow in gmin_get_var_int() When gmin_get_config_var() calls efi.get_variable() and the EFI variable is larger than the expected buffer size, two behaviors combine to create a stack buffer overflow: 1. gmin_get_config_var() does not return the proper error code when efi.get_variable() fails. It returns the stale 'ret' value from earlier operations instead of indicating the EFI failure. 2. When efi.get_variable() returns EFI_BUFFER_TOO_SMALL, it updates *out_len to the required buffer size but writes no data to the output buffer. However, due to bug #1, gmin_get_var_int() believes the call succeeded. The caller gmin_get_var_int() then performs: - Allocates val[CFG_VAR_NAME_MAX + 1] (65 bytes) on stack - Calls gmin_get_config_var(dev, is_gmin, var, val, &len) with len=64 - If EFI variable is >64 bytes, efi.get_variable() sets len=required_size - Due to bug #1, thinks call succeeded with len=required_size - Executes val[len] = 0, writing past end of 65-byte stack buffer This creates a stack buffer overflow when EFI variables are larger than 64 bytes. Since EFI variables can be controlled by firmware or system configuration, this could potentially be exploited for code execution. Fix the bug by returning proper error codes from gmin_get_config_var() based on EFI status instead of stale 'ret' value. The gmin_get_var_int() function is called during device initialization for camera sensor configuration on Intel Bay Trail and Cherry Trail platforms using the atomisp camera stack.

Linux Kernel nftables Out-Of-Bounds Read/Write Vulnerability; nft_byteorder poorly handled vm register contents when CAP_NET_ADMIN is in any user or network namespace

In the Linux kernel, the following vulnerability has been resolved: ASoC: qcom: Fix sc7280 lpass potential buffer overflow Case values introduced in commit 5f78e1fb7a3e ("ASoC: qcom: Add driver support for audioreach solution") cause out of bounds access in arrays of sc7280 driver data (e.g. in case of RX_CODEC_DMA_RX_0 in sc7280_snd_hw_params()). Redefine LPASS_MAX_PORTS to consider the maximum possible port id for q6dsp as sc7280 driver utilizes some of those values. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: xdp: produce a warning when calculated tailroom is negative Many ethernet drivers report xdp Rx queue frag size as being the same as DMA write size. However, the only user of this field, namely bpf_xdp_frags_increase_tail(), clearly expects a truesize. Such difference leads to unspecific memory corruption issues under certain circumstances, e.g. in ixgbevf maximum DMA write size is 3 KB, so when running xskxceiver's XDP_ADJUST_TAIL_GROW_MULTI_BUFF, 6K packet fully uses all DMA-writable space in 2 buffers. This would be fine, if only rxq->frag_size was properly set to 4K, but value of 3K results in a negative tailroom, because there is a non-zero page offset. We are supposed to return -EINVAL and be done with it in such case, but due to tailroom being stored as an unsigned int, it is reported to be somewhere near UINT_MAX, resulting in a tail being grown, even if the requested offset is too much (it is around 2K in the abovementioned test). This later leads to all kinds of unspecific calltraces. [ 7340.337579] xskxceiver[1440]: segfault at 1da718 ip 00007f4161aeac9d sp 00007f41615a6a00 error 6 [ 7340.338040] xskxceiver[1441]: segfault at 7f410000000b ip 00000000004042b5 sp 00007f415bffecf0 error 4 [ 7340.338179] in libc.so.6[61c9d,7f4161aaf000+160000] [ 7340.339230] in xskxceiver[42b5,400000+69000] [ 7340.340300] likely on CPU 6 (core 0, socket 6) [ 7340.340302] Code: ff ff 01 e9 f4 fe ff ff 0f 1f 44 00 00 4c 39 f0 74 73 31 c0 ba 01 00 00 00 f0 0f b1 17 0f 85 ba 00 00 00 49 8b 87 88 00 00 00 <4c> 89 70 08 eb cc 0f 1f 44 00 00 48 8d bd f0 fe ff ff 89 85 ec fe [ 7340.340888] likely on CPU 3 (core 0, socket 3) [ 7340.345088] Code: 00 00 00 ba 00 00 00 00 be 00 00 00 00 89 c7 e8 31 ca ff ff 89 45 ec 8b 45 ec 85 c0 78 07 b8 00 00 00 00 eb 46 e8 0b c8 ff ff <8b> 00 83 f8 69 74 24 e8 ff c7 ff ff 8b 00 83 f8 0b 74 18 e8 f3 c7 [ 7340.404334] Oops: general protection fault, probably for non-canonical address 0x6d255010bdffc: 0000 [#1] SMP NOPTI [ 7340.405972] CPU: 7 UID: 0 PID: 1439 Comm: xskxceiver Not tainted 6.19.0-rc1+ #21 PREEMPT(lazy) [ 7340.408006] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-5.fc42 04/01/2014 [ 7340.409716] RIP: 0010:lookup_swap_cgroup_id+0x44/0x80 [ 7340.410455] Code: 83 f8 1c 73 39 48 ba ff ff ff ff ff ff ff 03 48 8b 04 c5 20 55 fa bd 48 21 d1 48 89 ca 83 e1 01 48 d1 ea c1 e1 04 48 8d 04 90 <8b> 00 48 83 c4 10 d3 e8 c3 cc cc cc cc 31 c0 e9 98 b7 dd 00 48 89 [ 7340.412787] RSP: 0018:ffffcc5c04f7f6d0 EFLAGS: 00010202 [ 7340.413494] RAX: 0006d255010bdffc RBX: ffff891f477895a8 RCX: 0000000000000010 [ 7340.414431] RDX: 0001c17e3fffffff RSI: 00fa070000000000 RDI: 000382fc7fffffff [ 7340.415354] RBP: 00fa070000000000 R08: ffffcc5c04f7f8f8 R09: ffffcc5c04f7f7d0 [ 7340.416283] R10: ffff891f4c1a7000 R11: ffffcc5c04f7f9c8 R12: ffffcc5c04f7f7d0 [ 7340.417218] R13: 03ffffffffffffff R14: 00fa06fffffffe00 R15: ffff891f47789500 [ 7340.418229] FS: 0000000000000000(0000) GS:ffff891ffdfaa000(0000) knlGS:0000000000000000 [ 7340.419489] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 7340.420286] CR2: 00007f415bfffd58 CR3: 0000000103f03002 CR4: 0000000000772ef0 [ 7340.421237] PKRU: 55555554 [ 7340.421623] Call Trace: [ 7340.421987] <TASK> [ 7340.422309] ? softleaf_from_pte+0x77/0xa0 [ 7340.422855] swap_pte_batch+0xa7/0x290 [ 7340.423363] zap_nonpresent_ptes.constprop.0.isra.0+0xd1/0x270 [ 7340.424102] zap_pte_range+0x281/0x580 [ 7340.424607] zap_pmd_range.isra.0+0xc9/0x240 [ 7340.425177] unmap_page_range+0x24d/0x420 [ 7340.425714] unmap_vmas+0xa1/0x180 [ 7340.426185] exit_mmap+0xe1/0x3b0 [ 7340.426644] __mmput+0x41/0x150 [ 7340.427098] exit_mm+0xb1/0x110 [ 7340.427539] do_exit+0x1b2/0x460 [ 7340.427992] do_group_exit+0x2d/0xc0 [ 7340.428477] get_signal+0x79d/0x7e0 [ 7340.428957] arch_do_signal_or_restart+0x34/0x100 [ 7340.429571] exit_to_user_mode_loop+0x8e/0x4c0 [ 7340.430159] do_syscall_64+0x188/ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: mm: use aligned address in clear_gigantic_page() In current kernel, hugetlb_no_page() calls folio_zero_user() with the fault address. Where the fault address may be not aligned with the huge page size. Then, folio_zero_user() may call clear_gigantic_page() with the address, while clear_gigantic_page() requires the address to be huge page size aligned. So, this may cause memory corruption or information leak, addtional, use more obvious naming 'addr_hint' instead of 'addr' for clear_gigantic_page().

In the Linux kernel, the following vulnerability has been resolved: arm64: entry: avoid kprobe recursion The cortex_a76_erratum_1463225_debug_handler() function is called when handling debug exceptions (and synchronous exceptions from BRK instructions), and so is called when a probed function executes. If the compiler does not inline cortex_a76_erratum_1463225_debug_handler(), it can be probed. If cortex_a76_erratum_1463225_debug_handler() is probed, any debug exception or software breakpoint exception will result in recursive exceptions leading to a stack overflow. This can be triggered with the ftrace multiple_probes selftest, and as per the example splat below. This is a regression caused by commit: 6459b8469753e9fe ("arm64: entry: consolidate Cortex-A76 erratum 1463225 workaround") ... which removed the NOKPROBE_SYMBOL() annotation associated with the function. My intent was that cortex_a76_erratum_1463225_debug_handler() would be inlined into its caller, el1_dbg(), which is marked noinstr and cannot be probed. Mark cortex_a76_erratum_1463225_debug_handler() as __always_inline to ensure this. Example splat prior to this patch (with recursive entries elided): | # echo p cortex_a76_erratum_1463225_debug_handler > /sys/kernel/debug/tracing/kprobe_events | # echo p do_el0_svc >> /sys/kernel/debug/tracing/kprobe_events | # echo 1 > /sys/kernel/debug/tracing/events/kprobes/enable | Insufficient stack space to handle exception! | ESR: 0x0000000096000047 -- DABT (current EL) | FAR: 0xffff800009cefff0 | Task stack: [0xffff800009cf0000..0xffff800009cf4000] | IRQ stack: [0xffff800008000000..0xffff800008004000] | Overflow stack: [0xffff00007fbc00f0..0xffff00007fbc10f0] | CPU: 0 PID: 145 Comm: sh Not tainted 6.0.0 #2 | Hardware name: linux,dummy-virt (DT) | pstate: 604003c5 (nZCv DAIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) | pc : arm64_enter_el1_dbg+0x4/0x20 | lr : el1_dbg+0x24/0x5c | sp : ffff800009cf0000 | x29: ffff800009cf0000 x28: ffff000002c74740 x27: 0000000000000000 | x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 | x23: 00000000604003c5 x22: ffff80000801745c x21: 0000aaaac95ac068 | x20: 00000000f2000004 x19: ffff800009cf0040 x18: 0000000000000000 | x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 | x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 | x11: 0000000000000010 x10: ffff800008c87190 x9 : ffff800008ca00d0 | x8 : 000000000000003c x7 : 0000000000000000 x6 : 0000000000000000 | x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000000043a4 | x2 : 00000000f2000004 x1 : 00000000f2000004 x0 : ffff800009cf0040 | Kernel panic - not syncing: kernel stack overflow | CPU: 0 PID: 145 Comm: sh Not tainted 6.0.0 #2 | Hardware name: linux,dummy-virt (DT) | Call trace: | dump_backtrace+0xe4/0x104 | show_stack+0x18/0x4c | dump_stack_lvl+0x64/0x7c | dump_stack+0x18/0x38 | panic+0x14c/0x338 | test_taint+0x0/0x2c | panic_bad_stack+0x104/0x118 | handle_bad_stack+0x34/0x48 | __bad_stack+0x78/0x7c | arm64_enter_el1_dbg+0x4/0x20 | el1h_64_sync_handler+0x40/0x98 | el1h_64_sync+0x64/0x68 | cortex_a76_erratum_1463225_debug_handler+0x0/0x34 ... | el1h_64_sync_handler+0x40/0x98 | el1h_64_sync+0x64/0x68 | cortex_a76_erratum_1463225_debug_handler+0x0/0x34 ... | el1h_64_sync_handler+0x40/0x98 | el1h_64_sync+0x64/0x68 | cortex_a76_erratum_1463225_debug_handler+0x0/0x34 | el1h_64_sync_handler+0x40/0x98 | el1h_64_sync+0x64/0x68 | do_el0_svc+0x0/0x28 | el0t_64_sync_handler+0x84/0xf0 | el0t_64_sync+0x18c/0x190 | Kernel Offset: disabled | CPU features: 0x0080,00005021,19001080 | Memory Limit: none | ---[ end Kernel panic - not syncing: kernel stack overflow ]--- With this patch, cortex_a76_erratum_1463225_debug_handler() is inlined into el1_dbg(), and el1_dbg() cannot be probed: | # echo p cortex_a76_erratum_1463225_debug_handler > /sys/kernel/debug/tracing/kprobe_events | sh: write error: No such file or directory | # grep -w cortex_a76_errat ---truncated---

In the Linux kernel, the following vulnerability has been resolved: hwmon: (macsmc) Fix regressions in Apple Silicon SMC hwmon driver The recently added macsmc-hwmon driver contained several critical bugs in its sensor population logic and float conversion routines. Specifically: - The voltage sensor population loop used the wrong prefix ("volt-" instead of "voltage-") and incorrectly assigned sensors to the temperature sensor array (hwmon->temp.sensors) instead of the voltage sensor array (hwmon->volt.sensors). This would lead to out-of-bounds memory access or data corruption when both temperature and voltage sensors were present. - The float conversion in macsmc_hwmon_write_f32() had flawed exponent logic for values >= 2^24 and lacked masking for the mantissa, which could lead to incorrect values being written to the SMC. Fix these issues to ensure correct sensor registration and reliable manual fan control. Confirm that the reported overflow in FIELD_PREP is fixed by declaring macsmc_hwmon_write_f32() as __always_inline for a compile test.

In the Linux kernel, the following vulnerability has been resolved: xsk: Fix fragment node deletion to prevent buffer leak After commit b692bf9a7543 ("xsk: Get rid of xdp_buff_xsk::xskb_list_node"), the list_node field is reused for both the xskb pool list and the buffer free list, this causes a buffer leak as described below. xp_free() checks if a buffer is already on the free list using list_empty(&xskb->list_node). When list_del() is used to remove a node from the xskb pool list, it doesn't reinitialize the node pointers. This means list_empty() will return false even after the node has been removed, causing xp_free() to incorrectly skip adding the buffer to the free list. Fix this by using list_del_init() instead of list_del() in all fragment handling paths, this ensures the list node is reinitialized after removal, allowing the list_empty() to work correctly.