In the Linux kernel, the following vulnerability has been resolved: vfio/pds: Fix missing detach_ioas op When CONFIG_IOMMUFD is enabled and a device is bound to the pds_vfio_pci driver, the following WARN_ON() trace is seen and probe fails: WARNING: CPU: 0 PID: 5040 at drivers/vfio/vfio_main.c:317 __vfio_register_dev+0x130/0x140 [vfio] <...> pds_vfio_pci 0000:08:00.1: probe with driver pds_vfio_pci failed with error -22 This is because the driver's vfio_device_ops.detach_ioas isn't set. Fix this by using the generic vfio_iommufd_physical_detach_ioas function.

In the Linux kernel, the following vulnerability has been resolved: PCI: pnv_php: Clean up allocated IRQs on unplug When the root of a nested PCIe bridge configuration is unplugged, the pnv_php driver leaked the allocated IRQ resources for the child bridges' hotplug event notifications, resulting in a panic. Fix this by walking all child buses and deallocating all its IRQ resources before calling pci_hp_remove_devices(). Also modify the lifetime of the workqueue at struct pnv_php_slot::wq so that it is only destroyed in pnv_php_free_slot(), instead of pnv_php_disable_irq(). This is required since pnv_php_disable_irq() will now be called by workers triggered by hot unplug interrupts, so the workqueue needs to stay allocated. The abridged kernel panic that occurs without this patch is as follows: WARNING: CPU: 0 PID: 687 at kernel/irq/msi.c:292 msi_device_data_release+0x6c/0x9c CPU: 0 UID: 0 PID: 687 Comm: bash Not tainted 6.14.0-rc5+ #2 Call Trace: msi_device_data_release+0x34/0x9c (unreliable) release_nodes+0x64/0x13c devres_release_all+0xc0/0x140 device_del+0x2d4/0x46c pci_destroy_dev+0x5c/0x194 pci_hp_remove_devices+0x90/0x128 pci_hp_remove_devices+0x44/0x128 pnv_php_disable_slot+0x54/0xd4 power_write_file+0xf8/0x18c pci_slot_attr_store+0x40/0x5c sysfs_kf_write+0x64/0x78 kernfs_fop_write_iter+0x1b0/0x290 vfs_write+0x3bc/0x50c ksys_write+0x84/0x140 system_call_exception+0x124/0x230 system_call_vectored_common+0x15c/0x2ec [bhelgaas: tidy comments]

In the Linux kernel, the following vulnerability has been resolved: PCI: pnv_php: Fix surprise plug detection and recovery The existing PowerNV hotplug code did not handle surprise plug events correctly, leading to a complete failure of the hotplug system after device removal and a required reboot to detect new devices. This comes down to two issues: 1) When a device is surprise removed, often the bridge upstream port will cause a PE freeze on the PHB. If this freeze is not cleared, the MSI interrupts from the bridge hotplug notification logic will not be received by the kernel, stalling all plug events on all slots associated with the PE. 2) When a device is removed from a slot, regardless of surprise or programmatic removal, the associated PHB/PE ls left frozen. If this freeze is not cleared via a fundamental reset, skiboot is unable to clear the freeze and cannot retrain / rescan the slot. This also requires a reboot to clear the freeze and redetect the device in the slot. Issue the appropriate unfreeze and rescan commands on hotplug events, and don't oops on hotplug if pci_bus_to_OF_node() returns NULL. [bhelgaas: tidy comments]

In the Linux kernel, the following vulnerability has been resolved: net: drop UFO packets in udp_rcv_segment() When sending a packet with virtio_net_hdr to tun device, if the gso_type in virtio_net_hdr is SKB_GSO_UDP and the gso_size is less than udphdr size, below crash may happen. ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:4572! Oops: invalid opcode: 0000 [#1] SMP NOPTI CPU: 0 UID: 0 PID: 62 Comm: mytest Not tainted 6.16.0-rc7 #203 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:skb_pull_rcsum+0x8e/0xa0 Code: 00 00 5b c3 cc cc cc cc 8b 93 88 00 00 00 f7 da e8 37 44 38 00 f7 d8 89 83 88 00 00 00 48 8b 83 c8 00 00 00 5b c3 cc cc cc cc <0f> 0b 0f 0b 66 66 2e 0f 1f 84 00 000 RSP: 0018:ffffc900001fba38 EFLAGS: 00000297 RAX: 0000000000000004 RBX: ffff8880040c1000 RCX: ffffc900001fb948 RDX: ffff888003e6d700 RSI: 0000000000000008 RDI: ffff88800411a062 RBP: ffff8880040c1000 R08: 0000000000000000 R09: 0000000000000001 R10: ffff888003606c00 R11: 0000000000000001 R12: 0000000000000000 R13: ffff888004060900 R14: ffff888004050000 R15: ffff888004060900 FS: 000000002406d3c0(0000) GS:ffff888084a19000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000040 CR3: 0000000004007000 CR4: 00000000000006f0 Call Trace: <TASK> udp_queue_rcv_one_skb+0x176/0x4b0 net/ipv4/udp.c:2445 udp_queue_rcv_skb+0x155/0x1f0 net/ipv4/udp.c:2475 udp_unicast_rcv_skb+0x71/0x90 net/ipv4/udp.c:2626 __udp4_lib_rcv+0x433/0xb00 net/ipv4/udp.c:2690 ip_protocol_deliver_rcu+0xa6/0x160 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x72/0x90 net/ipv4/ip_input.c:233 ip_sublist_rcv_finish+0x5f/0x70 net/ipv4/ip_input.c:579 ip_sublist_rcv+0x122/0x1b0 net/ipv4/ip_input.c:636 ip_list_rcv+0xf7/0x130 net/ipv4/ip_input.c:670 __netif_receive_skb_list_core+0x21d/0x240 net/core/dev.c:6067 netif_receive_skb_list_internal+0x186/0x2b0 net/core/dev.c:6210 napi_complete_done+0x78/0x180 net/core/dev.c:6580 tun_get_user+0xa63/0x1120 drivers/net/tun.c:1909 tun_chr_write_iter+0x65/0xb0 drivers/net/tun.c:1984 vfs_write+0x300/0x420 fs/read_write.c:593 ksys_write+0x60/0xd0 fs/read_write.c:686 do_syscall_64+0x50/0x1c0 arch/x86/entry/syscall_64.c:63 </TASK> To trigger gso segment in udp_queue_rcv_skb(), we should also set option UDP_ENCAP_ESPINUDP to enable udp_sk(sk)->encap_rcv. When the encap_rcv hook return 1 in udp_queue_rcv_one_skb(), udp_csum_pull_header() will try to pull udphdr, but the skb size has been segmented to gso size, which leads to this crash. Previous commit cf329aa42b66 ("udp: cope with UDP GRO packet misdirection") introduces segmentation in UDP receive path only for GRO, which was never intended to be used for UFO, so drop UFO packets in udp_rcv_segment().

In the Linux kernel, the following vulnerability has been resolved: md: make rdev_addable usable for rcu mode Our testcase trigger panic: BUG: kernel NULL pointer dereference, address: 00000000000000e0 ... Oops: Oops: 0000 [#1] SMP NOPTI CPU: 2 UID: 0 PID: 85 Comm: kworker/2:1 Not tainted 6.16.0+ #94 PREEMPT(none) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 Workqueue: md_misc md_start_sync RIP: 0010:rdev_addable+0x4d/0xf0 ... Call Trace: <TASK> md_start_sync+0x329/0x480 process_one_work+0x226/0x6d0 worker_thread+0x19e/0x340 kthread+0x10f/0x250 ret_from_fork+0x14d/0x180 ret_from_fork_asm+0x1a/0x30 </TASK> Modules linked in: raid10 CR2: 00000000000000e0 ---[ end trace 0000000000000000 ]--- RIP: 0010:rdev_addable+0x4d/0xf0 md_spares_need_change in md_start_sync will call rdev_addable which protected by rcu_read_lock/rcu_read_unlock. This rcu context will help protect rdev won't be released, but rdev->mddev will be set to NULL before we call synchronize_rcu in md_kick_rdev_from_array. Fix this by using READ_ONCE and check does rdev->mddev still alive.

In the Linux kernel, the following vulnerability has been resolved: zloop: fix KASAN use-after-free of tag set When a zoned loop device, or zloop device, is removed, KASAN enabled kernel reports "BUG KASAN use-after-free" in blk_mq_free_tag_set(). The BUG happens because zloop_ctl_remove() calls put_disk(), which invokes zloop_free_disk(). The zloop_free_disk() frees the memory allocated for the zlo pointer. However, after the memory is freed, zloop_ctl_remove() calls blk_mq_free_tag_set(&zlo->tag_set), which accesses the freed zlo. Hence the KASAN use-after-free. zloop_ctl_remove() put_disk(zlo->disk) put_device() kobject_put() ... zloop_free_disk() kvfree(zlo) blk_mq_free_tag_set(&zlo->tag_set) To avoid the BUG, move the call to blk_mq_free_tag_set(&zlo->tag_set) from zloop_ctl_remove() into zloop_free_disk(). This ensures that the tag_set is freed before the call to kvfree(zlo).

In the Linux kernel, the following vulnerability has been resolved: media: ti: j721e-csi2rx: fix list_del corruption If ti_csi2rx_start_dma() fails in ti_csi2rx_dma_callback(), the buffer is marked done with VB2_BUF_STATE_ERROR but is not removed from the DMA queue. This causes the same buffer to be retried in the next iteration, resulting in a double list_del() and eventual list corruption. Fix this by removing the buffer from the queue before calling vb2_buffer_done() on error. This resolves a crash due to list_del corruption: [ 37.811243] j721e-csi2rx 30102000.ticsi2rx: Failed to queue the next buffer for DMA [ 37.832187] slab kmalloc-2k start ffff00000255b000 pointer offset 1064 size 2048 [ 37.839761] list_del corruption. next->prev should be ffff00000255bc28, but was ffff00000255d428. (next=ffff00000255b428) [ 37.850799] ------------[ cut here ]------------ [ 37.855424] kernel BUG at lib/list_debug.c:65! [ 37.859876] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP [ 37.866061] Modules linked in: i2c_dev usb_f_rndis u_ether libcomposite dwc3 udc_core usb_common aes_ce_blk aes_ce_cipher ghash_ce gf128mul sha1_ce cpufreq_dt dwc3_am62 phy_gmii_sel sa2ul [ 37.882830] CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.16.0-rc3+ #28 VOLUNTARY [ 37.890851] Hardware name: Bosch STLA-GSRV2-B0 (DT) [ 37.895737] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 37.902703] pc : __list_del_entry_valid_or_report+0xdc/0x114 [ 37.908390] lr : __list_del_entry_valid_or_report+0xdc/0x114 [ 37.914059] sp : ffff800080003db0 [ 37.917375] x29: ffff800080003db0 x28: 0000000000000007 x27: ffff800080e50000 [ 37.924521] x26: 0000000000000000 x25: ffff0000016abb50 x24: dead000000000122 [ 37.931666] x23: ffff0000016abb78 x22: ffff0000016ab080 x21: ffff800080003de0 [ 37.938810] x20: ffff00000255bc00 x19: ffff00000255b800 x18: 000000000000000a [ 37.945956] x17: 20747562202c3832 x16: 6362353532303030 x15: 0720072007200720 [ 37.953101] x14: 0720072007200720 x13: 0720072007200720 x12: 00000000ffffffea [ 37.960248] x11: ffff800080003b18 x10: 00000000ffffefff x9 : ffff800080f5b568 [ 37.967396] x8 : ffff800080f5b5c0 x7 : 0000000000017fe8 x6 : c0000000ffffefff [ 37.974542] x5 : ffff00000fea6688 x4 : 0000000000000000 x3 : 0000000000000000 [ 37.981686] x2 : 0000000000000000 x1 : ffff800080ef2b40 x0 : 000000000000006d [ 37.988832] Call trace: [ 37.991281] __list_del_entry_valid_or_report+0xdc/0x114 (P) [ 37.996959] ti_csi2rx_dma_callback+0x84/0x1c4 [ 38.001419] udma_vchan_complete+0x1e0/0x344 [ 38.005705] tasklet_action_common+0x118/0x310 [ 38.010163] tasklet_action+0x30/0x3c [ 38.013832] handle_softirqs+0x10c/0x2e0 [ 38.017761] __do_softirq+0x14/0x20 [ 38.021256] ____do_softirq+0x10/0x20 [ 38.024931] call_on_irq_stack+0x24/0x60 [ 38.028873] do_softirq_own_stack+0x1c/0x40 [ 38.033064] __irq_exit_rcu+0x130/0x15c [ 38.036909] irq_exit_rcu+0x10/0x20 [ 38.040403] el1_interrupt+0x38/0x60 [ 38.043987] el1h_64_irq_handler+0x18/0x24 [ 38.048091] el1h_64_irq+0x6c/0x70 [ 38.051501] default_idle_call+0x34/0xe0 (P) [ 38.055783] do_idle+0x1f8/0x250 [ 38.059021] cpu_startup_entry+0x34/0x3c [ 38.062951] rest_init+0xb4/0xc0 [ 38.066186] console_on_rootfs+0x0/0x6c [ 38.070031] __primary_switched+0x88/0x90 [ 38.074059] Code: b00037e0 91378000 f9400462 97e9bf49 (d4210000) [ 38.080168] ---[ end trace 0000000000000000 ]--- [ 38.084795] Kernel panic - not syncing: Oops - BUG: Fatal exception in interrupt [ 38.092197] SMP: stopping secondary CPUs [ 38.096139] Kernel Offset: disabled [ 38.099631] CPU features: 0x0000,00002000,02000801,0400420b [ 38.105202] Memory Limit: none [ 38.108260] ---[ end Kernel panic - not syncing: Oops - BUG: Fatal exception in interrupt ]---

In the Linux kernel, the following vulnerability has been resolved: vsock: Do not allow binding to VMADDR_PORT_ANY It is possible for a vsock to autobind to VMADDR_PORT_ANY. This can cause a use-after-free when a connection is made to the bound socket. The socket returned by accept() also has port VMADDR_PORT_ANY but is not on the list of unbound sockets. Binding it will result in an extra refcount decrement similar to the one fixed in fcdd2242c023 (vsock: Keep the binding until socket destruction). Modify the check in __vsock_bind_connectible() to also prevent binding to VMADDR_PORT_ANY.

In the Linux kernel, the following vulnerability has been resolved: net/packet: fix a race in packet_set_ring() and packet_notifier() When packet_set_ring() releases po->bind_lock, another thread can run packet_notifier() and process an NETDEV_UP event. This race and the fix are both similar to that of commit 15fe076edea7 ("net/packet: fix a race in packet_bind() and packet_notifier()"). There too the packet_notifier NETDEV_UP event managed to run while a po->bind_lock critical section had to be temporarily released. And the fix was similarly to temporarily set po->num to zero to keep the socket unhooked until the lock is retaken. The po->bind_lock in packet_set_ring and packet_notifier precede the introduction of git history.

In the Linux kernel, the following vulnerability has been resolved: tls: handle data disappearing from under the TLS ULP TLS expects that it owns the receive queue of the TCP socket. This cannot be guaranteed in case the reader of the TCP socket entered before the TLS ULP was installed, or uses some non-standard read API (eg. zerocopy ones). Replace the WARN_ON() and a buggy early exit (which leaves anchor pointing to a freed skb) with real error handling. Wipe the parsing state and tell the reader to retry. We already reload the anchor every time we (re)acquire the socket lock, so the only condition we need to avoid is an out of bounds read (not having enough bytes in the socket for previously parsed record len). If some data was read from under TLS but there's enough in the queue we'll reload and decrypt what is most likely not a valid TLS record. Leading to some undefined behavior from TLS perspective (corrupting a stream? missing an alert? missing an attack?) but no kernel crash should take place.

In the Linux kernel, the following vulnerability has been resolved: tls: stop recv() if initial process_rx_list gave us non-DATA If we have a non-DATA record on the rx_list and another record of the same type still on the queue, we will end up merging them: - process_rx_list copies the non-DATA record - we start the loop and process the first available record since it's of the same type - we break out of the loop since the record was not DATA Just check the record type and jump to the end in case process_rx_list did some work.

Out of bounds write in V8 in Google Chrome prior to 139.0.7258.138 allowed a remote attacker to potentially exploit heap corruption via a crafted HTML page. (Chromium security severity: High)

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: cancle set bad inode after removing name fails The reproducer uses a file0 on a ntfs3 file system with a corrupted i_link. When renaming, the file0's inode is marked as a bad inode because the file name cannot be deleted. The underlying bug is that make_bad_inode() is called on a live inode. In some cases it's "icache lookup finds a normal inode, d_splice_alias() is called to attach it to dentry, while another thread decides to call make_bad_inode() on it - that would evict it from icache, but we'd already found it there earlier". In some it's outright "we have an inode attached to dentry - that's how we got it in the first place; let's call make_bad_inode() on it just for shits and giggles".

In the Linux kernel, the following vulnerability has been resolved: eventpoll: Fix semi-unbounded recursion Ensure that epoll instances can never form a graph deeper than EP_MAX_NESTS+1 links. Currently, ep_loop_check_proc() ensures that the graph is loop-free and does some recursion depth checks, but those recursion depth checks don't limit the depth of the resulting tree for two reasons: - They don't look upwards in the tree. - If there are multiple downwards paths of different lengths, only one of the paths is actually considered for the depth check since commit 28d82dc1c4ed ("epoll: limit paths"). Essentially, the current recursion depth check in ep_loop_check_proc() just serves to prevent it from recursing too deeply while checking for loops. A more thorough check is done in reverse_path_check() after the new graph edge has already been created; this checks, among other things, that no paths going upwards from any non-epoll file with a length of more than 5 edges exist. However, this check does not apply to non-epoll files. As a result, it is possible to recurse to a depth of at least roughly 500, tested on v6.15. (I am unsure if deeper recursion is possible; and this may have changed with commit 8c44dac8add7 ("eventpoll: Fix priority inversion problem").) To fix it: 1. In ep_loop_check_proc(), note the subtree depth of each visited node, and use subtree depths for the total depth calculation even when a subtree has already been visited. 2. Add ep_get_upwards_depth_proc() for similarly determining the maximum depth of an upwards walk. 3. In ep_loop_check(), use these values to limit the total path length between epoll nodes to EP_MAX_NESTS edges.

In the Linux kernel, the following vulnerability has been resolved: staging: gpib: fix unset padding field copy back to userspace The introduction of a padding field in the gpib_board_info_ioctl is showing up as initialized data on the stack frame being copyied back to userspace in function board_info_ioctl. The simplest fix is to initialize the entire struct to zero to ensure all unassigned padding fields are zero'd before being copied back to userspace.

In the Linux kernel, the following vulnerability has been resolved: staging: fbtft: fix potential memory leak in fbtft_framebuffer_alloc() In the error paths after fb_info structure is successfully allocated, the memory allocated in fb_deferred_io_init() for info->pagerefs is not freed. Fix that by adding the cleanup function on the error path.

In the Linux kernel, the following vulnerability has been resolved: vmci: Prevent the dispatching of uninitialized payloads The reproducer executes the host's unlocked_ioctl call in two different tasks. When init_context fails, the struct vmci_event_ctx is not fully initialized when executing vmci_datagram_dispatch() to send events to all vm contexts. This affects the datagram taken from the datagram queue of its context by another task, because the datagram payload is not initialized according to the size payload_size, which causes the kernel data to leak to the user space. Before dispatching the datagram, and before setting the payload content, explicitly set the payload content to 0 to avoid data leakage caused by incomplete payload initialization.

In the Linux kernel, the following vulnerability has been resolved: powercap: dtpm_cpu: Fix NULL pointer dereference in get_pd_power_uw() The get_pd_power_uw() function can crash with a NULL pointer dereference when em_cpu_get() returns NULL. This occurs when a CPU becomes impossible during runtime, causing get_cpu_device() to return NULL, which propagates through em_cpu_get() and leads to a crash when em_span_cpus() dereferences the NULL pointer. Add a NULL check after em_cpu_get() and return 0 if unavailable, matching the existing fallback behavior in __dtpm_cpu_setup(). [ rjw: Drop an excess empty code line ]

In the Linux kernel, the following vulnerability has been resolved: PM / devfreq: Check governor before using governor->name Commit 96ffcdf239de ("PM / devfreq: Remove redundant governor_name from struct devfreq") removes governor_name and uses governor->name to replace it. But devfreq->governor may be NULL and directly using devfreq->governor->name may cause null pointer exception. Move the check of governor to before using governor->name.

In the Linux kernel, the following vulnerability has been resolved: bpf, ktls: Fix data corruption when using bpf_msg_pop_data() in ktls When sending plaintext data, we initially calculated the corresponding ciphertext length. However, if we later reduced the plaintext data length via socket policy, we failed to recalculate the ciphertext length. This results in transmitting buffers containing uninitialized data during ciphertext transmission. This causes uninitialized bytes to be appended after a complete "Application Data" packet, leading to errors on the receiving end when parsing TLS record.

In the Linux kernel, the following vulnerability has been resolved: bpf: handle jset (if a & b ...) as a jump in CFG computation BPF_JSET is a conditional jump and currently verifier.c:can_jump() does not know about that. This can lead to incorrect live registers and SCC computation. E.g. in the following example: 1: r0 = 1; 2: r2 = 2; 3: if r1 & 0x7 goto +1; 4: exit; 5: r0 = r2; 6: exit; W/o this fix insn_successors(3) will return only (4), a jump to (5) would be missed and r2 won't be marked as alive at (3).

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Avoid accessing uninitialized arvif->ar during beacon miss During beacon miss handling, ath12k driver iterates over active virtual interfaces (vifs) and attempts to access the radio object (ar) via arvif->deflink->ar. However, after commit aa80f12f3bed ("wifi: ath12k: defer vdev creation for MLO"), arvif is linked to a radio only after vdev creation, typically when a channel is assigned or a scan is requested. For P2P capable devices, a default P2P interface is created by wpa_supplicant along with regular station interfaces, these serve as dummy interfaces for P2P-capable stations, lack an associated netdev and initiate frequent scans to discover neighbor p2p devices. When a scan is initiated on such P2P vifs, driver selects destination radio (ar) based on scan frequency, creates a scan vdev, and attaches arvif to the radio. Once the scan completes or is aborted, the scan vdev is deleted, detaching arvif from the radio and leaving arvif->ar uninitialized. While handling beacon miss for station interfaces, P2P interface is also encountered in the vif iteration and ath12k_mac_handle_beacon_miss_iter() tries to dereference the uninitialized arvif->deflink->ar. Fix this by verifying that vdev is created for the arvif before accessing its ar during beacon miss handling and similar vif iterator callbacks. ========================================================================== wlp6s0: detected beacon loss from AP (missed 7 beacons) - probing KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017] CPU: 5 UID: 0 PID: 0 Comm: swapper/5 Not tainted 6.16.0-rc1-wt-ath+ #2 PREEMPT(full) RIP: 0010:ath12k_mac_handle_beacon_miss_iter+0xb5/0x1a0 [ath12k] Call Trace: __iterate_interfaces+0x11a/0x410 [mac80211] ieee80211_iterate_active_interfaces_atomic+0x61/0x140 [mac80211] ath12k_mac_handle_beacon_miss+0xa1/0xf0 [ath12k] ath12k_roam_event+0x393/0x560 [ath12k] ath12k_wmi_op_rx+0x1486/0x28c0 [ath12k] ath12k_htc_process_trailer.isra.0+0x2fb/0x620 [ath12k] ath12k_htc_rx_completion_handler+0x448/0x830 [ath12k] ath12k_ce_recv_process_cb+0x549/0x9e0 [ath12k] ath12k_ce_per_engine_service+0xbe/0xf0 [ath12k] ath12k_pci_ce_workqueue+0x69/0x120 [ath12k] process_one_work+0xe3a/0x1430 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Pass ab pointer directly to ath12k_dp_tx_get_encap_type() In ath12k_dp_tx_get_encap_type(), the arvif parameter is only used to retrieve the ab pointer. In vdev delete sequence the arvif->ar could become NULL and that would trigger kernel panic. Since the caller ath12k_dp_tx() already has a valid ab pointer, pass it directly to avoid panic and unnecessary dereferencing. PC points to "ath12k_dp_tx+0x228/0x988 [ath12k]" LR points to "ath12k_dp_tx+0xc8/0x988 [ath12k]". The Backtrace obtained is as follows: ath12k_dp_tx+0x228/0x988 [ath12k] ath12k_mac_tx_check_max_limit+0x608/0x920 [ath12k] ieee80211_process_measurement_req+0x320/0x348 [mac80211] ieee80211_tx_dequeue+0x9ac/0x1518 [mac80211] ieee80211_tx_dequeue+0xb14/0x1518 [mac80211] ieee80211_tx_prepare_skb+0x224/0x254 [mac80211] ieee80211_xmit+0xec/0x100 [mac80211] __ieee80211_subif_start_xmit+0xc50/0xf40 [mac80211] ieee80211_subif_start_xmit+0x2e8/0x308 [mac80211] netdev_start_xmit+0x150/0x18c dev_hard_start_xmit+0x74/0xc0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: wifi: rtl818x: Kill URBs before clearing tx status queue In rtl8187_stop() move the call of usb_kill_anchored_urbs() before clearing b_tx_status.queue. This change prevents callbacks from using already freed skb due to anchor was not killed before freeing such skb. BUG: kernel NULL pointer dereference, address: 0000000000000080 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] SMP NOPTI CPU: 7 UID: 0 PID: 0 Comm: swapper/7 Not tainted 6.15.0 #8 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.0.0 02/06/2015 RIP: 0010:ieee80211_tx_status_irqsafe+0x21/0xc0 [mac80211] Call Trace: <IRQ> rtl8187_tx_cb+0x116/0x150 [rtl8187] __usb_hcd_giveback_urb+0x9d/0x120 usb_giveback_urb_bh+0xbb/0x140 process_one_work+0x19b/0x3c0 bh_worker+0x1a7/0x210 tasklet_action+0x10/0x30 handle_softirqs+0xf0/0x340 __irq_exit_rcu+0xcd/0xf0 common_interrupt+0x85/0xa0 </IRQ> Tested on RTL8187BvE device. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix slab-use-after-free in amdgpu_userq_mgr_fini+0x70c The issue was reproduced on NV10 using IGT pci_unplug test. It is expected that `amdgpu_driver_postclose_kms()` is called prior to `amdgpu_drm_release()`. However, the bug is that `amdgpu_fpriv` was freed in `amdgpu_driver_postclose_kms()`, and then later accessed in `amdgpu_drm_release()` via a call to `amdgpu_userq_mgr_fini()`. As a result, KASAN detected a use-after-free condition, as shown in the log below. The proposed fix is to move the calls to `amdgpu_eviction_fence_destroy()` and `amdgpu_userq_mgr_fini()` into `amdgpu_driver_postclose_kms()`, so they are invoked before `amdgpu_fpriv` is freed. This also ensures symmetry with the initialization path in `amdgpu_driver_open_kms()`, where the following components are initialized: - `amdgpu_userq_mgr_init()` - `amdgpu_eviction_fence_init()` - `amdgpu_ctx_mgr_init()` Correspondingly, in `amdgpu_driver_postclose_kms()` we should clean up using: - `amdgpu_userq_mgr_fini()` - `amdgpu_eviction_fence_destroy()` - `amdgpu_ctx_mgr_fini()` This change eliminates the use-after-free and improves consistency in resource management between open and close paths. [ +0.094367] ================================================================== [ +0.000026] BUG: KASAN: slab-use-after-free in amdgpu_userq_mgr_fini+0x70c/0x730 [amdgpu] [ +0.000866] Write of size 8 at addr ffff88811c068c60 by task amd_pci_unplug/1737 [ +0.000026] CPU: 3 UID: 0 PID: 1737 Comm: amd_pci_unplug Not tainted 6.14.0+ #2 [ +0.000008] Hardware name: ASUS System Product Name/ROG STRIX B550-F GAMING (WI-FI), BIOS 1401 12/03/2020 [ +0.000004] Call Trace: [ +0.000004] <TASK> [ +0.000003] dump_stack_lvl+0x76/0xa0 [ +0.000010] print_report+0xce/0x600 [ +0.000009] ? amdgpu_userq_mgr_fini+0x70c/0x730 [amdgpu] [ +0.000790] ? srso_return_thunk+0x5/0x5f [ +0.000007] ? kasan_complete_mode_report_info+0x76/0x200 [ +0.000008] ? amdgpu_userq_mgr_fini+0x70c/0x730 [amdgpu] [ +0.000684] kasan_report+0xbe/0x110 [ +0.000007] ? amdgpu_userq_mgr_fini+0x70c/0x730 [amdgpu] [ +0.000601] __asan_report_store8_noabort+0x17/0x30 [ +0.000007] amdgpu_userq_mgr_fini+0x70c/0x730 [amdgpu] [ +0.000801] ? __pfx_amdgpu_userq_mgr_fini+0x10/0x10 [amdgpu] [ +0.000819] ? srso_return_thunk+0x5/0x5f [ +0.000008] amdgpu_drm_release+0xa3/0xe0 [amdgpu] [ +0.000604] __fput+0x354/0xa90 [ +0.000010] __fput_sync+0x59/0x80 [ +0.000005] __x64_sys_close+0x7d/0xe0 [ +0.000006] x64_sys_call+0x2505/0x26f0 [ +0.000006] do_syscall_64+0x7c/0x170 [ +0.000004] ? kasan_record_aux_stack+0xae/0xd0 [ +0.000005] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? kmem_cache_free+0x398/0x580 [ +0.000006] ? __fput+0x543/0xa90 [ +0.000006] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? __fput+0x543/0xa90 [ +0.000004] ? __kasan_check_read+0x11/0x20 [ +0.000007] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? __kasan_check_read+0x11/0x20 [ +0.000003] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? fpregs_assert_state_consistent+0x21/0xb0 [ +0.000006] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? syscall_exit_to_user_mode+0x4e/0x240 [ +0.000005] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? do_syscall_64+0x88/0x170 [ +0.000003] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? do_syscall_64+0x88/0x170 [ +0.000004] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? irqentry_exit+0x43/0x50 [ +0.000004] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? exc_page_fault+0x7c/0x110 [ +0.000006] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ +0.000005] RIP: 0033:0x7ffff7b14f67 [ +0.000005] Code: ff e8 0d 16 02 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 41 c3 48 83 ec 18 89 7c 24 0c e8 73 ba f7 ff [ +0.000004] RSP: 002b:00007fffffffe358 EFLAGS: 00000246 ORIG_RAX: 0000000000000003 [ +0.000006] RAX: ffffffffff ---truncated---

In the Linux kernel, the following vulnerability has been resolved: iwlwifi: Add missing check for alloc_ordered_workqueue Add check for the return value of alloc_ordered_workqueue since it may return NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: clear initialized flag for deinit-ed srng lists In a number of cases we see kernel panics on resume due to ath11k kernel page fault, which happens under the following circumstances: 1) First ath11k_hal_dump_srng_stats() call Last interrupt received for each group: ath11k_pci 0000:01:00.0: group_id 0 22511ms before ath11k_pci 0000:01:00.0: group_id 1 14440788ms before [..] ath11k_pci 0000:01:00.0: failed to receive control response completion, polling.. ath11k_pci 0000:01:00.0: Service connect timeout ath11k_pci 0000:01:00.0: failed to connect to HTT: -110 ath11k_pci 0000:01:00.0: failed to start core: -110 ath11k_pci 0000:01:00.0: firmware crashed: MHI_CB_EE_RDDM ath11k_pci 0000:01:00.0: already resetting count 2 ath11k_pci 0000:01:00.0: failed to wait wlan mode request (mode 4): -110 ath11k_pci 0000:01:00.0: qmi failed to send wlan mode off: -110 ath11k_pci 0000:01:00.0: failed to reconfigure driver on crash recovery [..] 2) At this point reconfiguration fails (we have 2 resets) and ath11k_core_reconfigure_on_crash() calls ath11k_hal_srng_deinit() which destroys srng lists. However, it does not reset per-list ->initialized flag. 3) Second ath11k_hal_dump_srng_stats() call sees stale ->initialized flag and attempts to dump srng stats: Last interrupt received for each group: ath11k_pci 0000:01:00.0: group_id 0 66785ms before ath11k_pci 0000:01:00.0: group_id 1 14485062ms before ath11k_pci 0000:01:00.0: group_id 2 14485062ms before ath11k_pci 0000:01:00.0: group_id 3 14485062ms before ath11k_pci 0000:01:00.0: group_id 4 14780845ms before ath11k_pci 0000:01:00.0: group_id 5 14780845ms before ath11k_pci 0000:01:00.0: group_id 6 14485062ms before ath11k_pci 0000:01:00.0: group_id 7 66814ms before ath11k_pci 0000:01:00.0: group_id 8 68997ms before ath11k_pci 0000:01:00.0: group_id 9 67588ms before ath11k_pci 0000:01:00.0: group_id 10 69511ms before BUG: unable to handle page fault for address: ffffa007404eb010 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 100000067 P4D 100000067 PUD 10022d067 PMD 100b01067 PTE 0 Oops: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k] Call Trace: <TASK> ? __die_body+0xae/0xb0 ? page_fault_oops+0x381/0x3e0 ? exc_page_fault+0x69/0xa0 ? asm_exc_page_fault+0x22/0x30 ? ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k (HASH:6cea 4)] ath11k_qmi_driver_event_work+0xbd/0x1050 [ath11k (HASH:6cea 4)] worker_thread+0x389/0x930 kthread+0x149/0x170 Clear per-list ->initialized flag in ath11k_hal_srng_deinit().

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7925: fix off by one in mt7925_mcu_hw_scan() The ssid->ssids[] and sreq->ssids[] arrays have MT7925_RNR_SCAN_MAX_BSSIDS elements so this >= needs to be > to prevent an out of bounds access.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: Fix possible OOB access in mt7996_tx() Fis possible Out-Of-Boundary access in mt7996_tx routine if link_id is set to IEEE80211_LINK_UNSPECIFIED

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix use-after-free in amdgpu_userq_suspend+0x51a/0x5a0 [ +0.000020] BUG: KASAN: slab-use-after-free in amdgpu_userq_suspend+0x51a/0x5a0 [amdgpu] [ +0.000817] Read of size 8 at addr ffff88812eec8c58 by task amd_pci_unplug/1733 [ +0.000027] CPU: 10 UID: 0 PID: 1733 Comm: amd_pci_unplug Tainted: G W 6.14.0+ #2 [ +0.000009] Tainted: [W]=WARN [ +0.000003] Hardware name: ASUS System Product Name/ROG STRIX B550-F GAMING (WI-FI), BIOS 1401 12/03/2020 [ +0.000004] Call Trace: [ +0.000004] <TASK> [ +0.000003] dump_stack_lvl+0x76/0xa0 [ +0.000011] print_report+0xce/0x600 [ +0.000009] ? srso_return_thunk+0x5/0x5f [ +0.000006] ? kasan_complete_mode_report_info+0x76/0x200 [ +0.000007] ? kasan_addr_to_slab+0xd/0xb0 [ +0.000006] ? amdgpu_userq_suspend+0x51a/0x5a0 [amdgpu] [ +0.000707] kasan_report+0xbe/0x110 [ +0.000006] ? amdgpu_userq_suspend+0x51a/0x5a0 [amdgpu] [ +0.000541] __asan_report_load8_noabort+0x14/0x30 [ +0.000005] amdgpu_userq_suspend+0x51a/0x5a0 [amdgpu] [ +0.000535] ? stop_cpsch+0x396/0x600 [amdgpu] [ +0.000556] ? stop_cpsch+0x429/0x600 [amdgpu] [ +0.000536] ? __pfx_amdgpu_userq_suspend+0x10/0x10 [amdgpu] [ +0.000536] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? kgd2kfd_suspend+0x132/0x1d0 [amdgpu] [ +0.000542] amdgpu_device_fini_hw+0x581/0xe90 [amdgpu] [ +0.000485] ? down_write+0xbb/0x140 [ +0.000007] ? __mutex_unlock_slowpath.constprop.0+0x317/0x360 [ +0.000005] ? __pfx_amdgpu_device_fini_hw+0x10/0x10 [amdgpu] [ +0.000482] ? __kasan_check_write+0x14/0x30 [ +0.000004] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? up_write+0x55/0xb0 [ +0.000007] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? blocking_notifier_chain_unregister+0x6c/0xc0 [ +0.000008] amdgpu_driver_unload_kms+0x69/0x90 [amdgpu] [ +0.000484] amdgpu_pci_remove+0x93/0x130 [amdgpu] [ +0.000482] pci_device_remove+0xae/0x1e0 [ +0.000008] device_remove+0xc7/0x180 [ +0.000008] device_release_driver_internal+0x3d4/0x5a0 [ +0.000007] device_release_driver+0x12/0x20 [ +0.000004] pci_stop_bus_device+0x104/0x150 [ +0.000006] pci_stop_and_remove_bus_device_locked+0x1b/0x40 [ +0.000005] remove_store+0xd7/0xf0 [ +0.000005] ? __pfx_remove_store+0x10/0x10 [ +0.000006] ? __pfx__copy_from_iter+0x10/0x10 [ +0.000006] ? __pfx_dev_attr_store+0x10/0x10 [ +0.000006] dev_attr_store+0x3f/0x80 [ +0.000006] sysfs_kf_write+0x125/0x1d0 [ +0.000004] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? __kasan_check_write+0x14/0x30 [ +0.000005] kernfs_fop_write_iter+0x2ea/0x490 [ +0.000005] ? rw_verify_area+0x70/0x420 [ +0.000005] ? __pfx_kernfs_fop_write_iter+0x10/0x10 [ +0.000006] vfs_write+0x90d/0xe70 [ +0.000005] ? srso_return_thunk+0x5/0x5f [ +0.000005] ? __pfx_vfs_write+0x10/0x10 [ +0.000004] ? local_clock+0x15/0x30 [ +0.000008] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? __kasan_slab_free+0x5f/0x80 [ +0.000005] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? __kasan_check_read+0x11/0x20 [ +0.000004] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? fdget_pos+0x1d3/0x500 [ +0.000007] ksys_write+0x119/0x220 [ +0.000005] ? putname+0x1c/0x30 [ +0.000006] ? __pfx_ksys_write+0x10/0x10 [ +0.000007] __x64_sys_write+0x72/0xc0 [ +0.000006] x64_sys_call+0x18ab/0x26f0 [ +0.000006] do_syscall_64+0x7c/0x170 [ +0.000004] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? __pfx___x64_sys_openat+0x10/0x10 [ +0.000006] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? __kasan_check_read+0x11/0x20 [ +0.000003] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? fpregs_assert_state_consistent+0x21/0xb0 [ +0.000006] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? syscall_exit_to_user_mode+0x4e/0x240 [ +0.000005] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? do_syscall_64+0x88/0x170 [ +0.000003] ? srso_return_thunk+0x5/0x5f [ +0.000004] ? irqentry_exit+0x43/0x50 [ +0.000004] ? srso_return_thunk+0x5 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/rockchip: vop2: fail cleanly if missing a primary plane for a video-port Each window of a vop2 is usable by a specific set of video ports, so while binding the vop2, we look through the list of available windows trying to find one designated as primary-plane and usable by that specific port. The code later wants to use drm_crtc_init_with_planes with that found primary plane, but nothing has checked so far if a primary plane was actually found. For whatever reason, the rk3576 vp2 does not have a usable primary window (if vp0 is also in use) which brought the issue to light and ended in a null-pointer dereference further down. As we expect a primary-plane to exist for a video-port, add a check at the end of the window-iteration and fail probing if none was found.

In the Linux kernel, the following vulnerability has been resolved: drm/panthor: Fix UAF in panthor_gem_create_with_handle() debugfs code The object is potentially already gone after the drm_gem_object_put(). In general the object should be fully constructed before calling drm_gem_handle_create(), except the debugfs tracking uses a separate lock and list and separate flag to denotate whether the object is actually initialized. Since I'm touching this all anyway simplify this by only adding the object to the debugfs when it's ready for that, which allows us to delete that separate flag. panthor_gem_debugfs_bo_rm() already checks whether we've actually been added to the list or this is some error path cleanup. v2: Fix build issues for !CONFIG_DEBUGFS (Adrián) v3: Add linebreak and remove outdated comment (Liviu)

In the Linux kernel, the following vulnerability has been resolved: xen: fix UAF in dmabuf_exp_from_pages() [dma_buf_fd() fixes; no preferences regarding the tree it goes through - up to xen folks] As soon as we'd inserted a file reference into descriptor table, another thread could close it. That's fine for the case when all we are doing is returning that descriptor to userland (it's a race, but it's a userland race and there's nothing the kernel can do about it). However, if we follow fd_install() with any kind of access to objects that would be destroyed on close (be it the struct file itself or anything destroyed by its ->release()), we have a UAF. dma_buf_fd() is a combination of reserving a descriptor and fd_install(). gntdev dmabuf_exp_from_pages() calls it and then proceeds to access the objects destroyed on close - starting with gntdev_dmabuf itself. Fix that by doing reserving descriptor before anything else and do fd_install() only when everything had been set up.

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Fix UAF on sva unbind with pending IOPFs Commit 17fce9d2336d ("iommu/vt-d: Put iopf enablement in domain attach path") disables IOPF on device by removing the device from its IOMMU's IOPF queue when the last IOPF-capable domain is detached from the device. Unfortunately, it did this in a wrong place where there are still pending IOPFs. As a result, a use-after-free error is potentially triggered and eventually a kernel panic with a kernel trace similar to the following: refcount_t: underflow; use-after-free. WARNING: CPU: 3 PID: 313 at lib/refcount.c:28 refcount_warn_saturate+0xd8/0xe0 Workqueue: iopf_queue/dmar0-iopfq iommu_sva_handle_iopf Call Trace: <TASK> iopf_free_group+0xe/0x20 process_one_work+0x197/0x3d0 worker_thread+0x23a/0x350 ? rescuer_thread+0x4a0/0x4a0 kthread+0xf8/0x230 ? finish_task_switch.isra.0+0x81/0x260 ? kthreads_online_cpu+0x110/0x110 ? kthreads_online_cpu+0x110/0x110 ret_from_fork+0x13b/0x170 ? kthreads_online_cpu+0x110/0x110 ret_from_fork_asm+0x11/0x20 </TASK> ---[ end trace 0000000000000000 ]--- The intel_pasid_tear_down_entry() function is responsible for blocking hardware from generating new page faults and flushing all in-flight ones. Therefore, moving iopf_for_domain_remove() after this function should resolve this.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_sync: fix double free in 'hci_discovery_filter_clear()' Function 'hci_discovery_filter_clear()' frees 'uuids' array and then sets it to NULL. There is a tiny chance of the following race: 'hci_cmd_sync_work()' 'update_passive_scan_sync()' 'hci_update_passive_scan_sync()' 'hci_discovery_filter_clear()' kfree(uuids); <-------------------------preempted--------------------------------> 'start_service_discovery()' 'hci_discovery_filter_clear()' kfree(uuids); // DOUBLE FREE <-------------------------preempted--------------------------------> uuids = NULL; To fix it let's add locking around 'kfree()' call and NULL pointer assignment. Otherwise the following backtrace fires: [ ] ------------[ cut here ]------------ [ ] kernel BUG at mm/slub.c:547! [ ] Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP [ ] CPU: 3 UID: 0 PID: 246 Comm: bluetoothd Tainted: G O 6.12.19-kernel #1 [ ] Tainted: [O]=OOT_MODULE [ ] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ ] pc : __slab_free+0xf8/0x348 [ ] lr : __slab_free+0x48/0x348 ... [ ] Call trace: [ ] __slab_free+0xf8/0x348 [ ] kfree+0x164/0x27c [ ] start_service_discovery+0x1d0/0x2c0 [ ] hci_sock_sendmsg+0x518/0x924 [ ] __sock_sendmsg+0x54/0x60 [ ] sock_write_iter+0x98/0xf8 [ ] do_iter_readv_writev+0xe4/0x1c8 [ ] vfs_writev+0x128/0x2b0 [ ] do_writev+0xfc/0x118 [ ] __arm64_sys_writev+0x20/0x2c [ ] invoke_syscall+0x68/0xf0 [ ] el0_svc_common.constprop.0+0x40/0xe0 [ ] do_el0_svc+0x1c/0x28 [ ] el0_svc+0x30/0xd0 [ ] el0t_64_sync_handler+0x100/0x12c [ ] el0t_64_sync+0x194/0x198 [ ] Code: 8b0002e6 eb17031f 54fffbe1 d503201f (d4210000) [ ] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_devcd_dump: fix out-of-bounds via dev_coredumpv Currently both dev_coredumpv and skb_put_data in hci_devcd_dump use hdev->dump.head. However, dev_coredumpv can free the buffer. From dev_coredumpm_timeout documentation, which is used by dev_coredumpv: > Creates a new device coredump for the given device. If a previous one hasn't > been read yet, the new coredump is discarded. The data lifetime is determined > by the device coredump framework and when it is no longer needed the @free > function will be called to free the data. If the data has not been read by the userspace yet, dev_coredumpv will discard new buffer, freeing hdev->dump.head. This leads to vmalloc-out-of-bounds error when skb_put_data tries to access hdev->dump.head. A crash report from syzbot illustrates this: ================================================================== BUG: KASAN: vmalloc-out-of-bounds in skb_put_data include/linux/skbuff.h:2752 [inline] BUG: KASAN: vmalloc-out-of-bounds in hci_devcd_dump+0x142/0x240 net/bluetooth/coredump.c:258 Read of size 140 at addr ffffc90004ed5000 by task kworker/u9:2/5844 CPU: 1 UID: 0 PID: 5844 Comm: kworker/u9:2 Not tainted 6.14.0-syzkaller-10892-g4e82c87058f4 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Workqueue: hci0 hci_devcd_timeout Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xc3/0x670 mm/kasan/report.c:521 kasan_report+0xe0/0x110 mm/kasan/report.c:634 check_region_inline mm/kasan/generic.c:183 [inline] kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189 __asan_memcpy+0x23/0x60 mm/kasan/shadow.c:105 skb_put_data include/linux/skbuff.h:2752 [inline] hci_devcd_dump+0x142/0x240 net/bluetooth/coredump.c:258 hci_devcd_timeout+0xb5/0x2e0 net/bluetooth/coredump.c:413 process_one_work+0x9cc/0x1b70 kernel/workqueue.c:3238 process_scheduled_works kernel/workqueue.c:3319 [inline] worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400 kthread+0x3c2/0x780 kernel/kthread.c:464 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> The buggy address ffffc90004ed5000 belongs to a vmalloc virtual mapping Memory state around the buggy address: ffffc90004ed4f00: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc90004ed4f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 >ffffc90004ed5000: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ^ ffffc90004ed5080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc90004ed5100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ================================================================== To avoid this issue, reorder dev_coredumpv to be called after skb_put_data that does not free the data.

In the Linux kernel, the following vulnerability has been resolved: bpf: Reject narrower access to pointer ctx fields The following BPF program, simplified from a syzkaller repro, causes a kernel warning: r0 = *(u8 *)(r1 + 169); exit; With pointer field sk being at offset 168 in __sk_buff. This access is detected as a narrower read in bpf_skb_is_valid_access because it doesn't match offsetof(struct __sk_buff, sk). It is therefore allowed and later proceeds to bpf_convert_ctx_access. Note that for the "is_narrower_load" case in the convert_ctx_accesses(), the insn->off is aligned, so the cnt may not be 0 because it matches the offsetof(struct __sk_buff, sk) in the bpf_convert_ctx_access. However, the target_size stays 0 and the verifier errors with a kernel warning: verifier bug: error during ctx access conversion(1) This patch fixes that to return a proper "invalid bpf_context access off=X size=Y" error on the load instruction. The same issue affects multiple other fields in context structures that allow narrow access. Some other non-affected fields (for sk_msg, sk_lookup, and sockopt) were also changed to use bpf_ctx_range_ptr for consistency. Note this syzkaller crash was reported in the "Closes" link below, which used to be about a different bug, fixed in commit fce7bd8e385a ("bpf/verifier: Handle BPF_LOAD_ACQ instructions in insn_def_regno()"). Because syzbot somehow confused the two bugs, the new crash and repro didn't get reported to the mailing list.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Remove skb secpath if xfrm state is not found Hardware returns a unique identifier for a decrypted packet's xfrm state, this state is looked up in an xarray. However, the state might have been freed by the time of this lookup. Currently, if the state is not found, only a counter is incremented. The secpath (sp) extension on the skb is not removed, resulting in sp->len becoming 0. Subsequently, functions like __xfrm_policy_check() attempt to access fields such as xfrm_input_state(skb)->xso.type (which dereferences sp->xvec[sp->len - 1]) without first validating sp->len. This leads to a crash when dereferencing an invalid state pointer. This patch prevents the crash by explicitly removing the secpath extension from the skb if the xfrm state is not found after hardware decryption. This ensures downstream functions do not operate on a zero-length secpath. BUG: unable to handle page fault for address: ffffffff000002c8 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 282e067 P4D 282e067 PUD 0 Oops: Oops: 0000 [#1] SMP CPU: 12 UID: 0 PID: 0 Comm: swapper/12 Not tainted 6.15.0-rc7_for_upstream_min_debug_2025_05_27_22_44 #1 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:__xfrm_policy_check+0x61a/0xa30 Code: b6 77 7f 83 e6 02 74 14 4d 8b af d8 00 00 00 41 0f b6 45 05 c1 e0 03 48 98 49 01 c5 41 8b 45 00 83 e8 01 48 98 49 8b 44 c5 10 <0f> b6 80 c8 02 00 00 83 e0 0c 3c 04 0f 84 0c 02 00 00 31 ff 80 fa RSP: 0018:ffff88885fb04918 EFLAGS: 00010297 RAX: ffffffff00000000 RBX: 0000000000000002 RCX: 0000000000000000 RDX: 0000000000000002 RSI: 0000000000000002 RDI: 0000000000000000 RBP: ffffffff8311af80 R08: 0000000000000020 R09: 00000000c2eda353 R10: ffff88812be2bbc8 R11: 000000001faab533 R12: ffff88885fb049c8 R13: ffff88812be2bbc8 R14: 0000000000000000 R15: ffff88811896ae00 FS: 0000000000000000(0000) GS:ffff8888dca82000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffff000002c8 CR3: 0000000243050002 CR4: 0000000000372eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> ? try_to_wake_up+0x108/0x4c0 ? udp4_lib_lookup2+0xbe/0x150 ? udp_lib_lport_inuse+0x100/0x100 ? __udp4_lib_lookup+0x2b0/0x410 __xfrm_policy_check2.constprop.0+0x11e/0x130 udp_queue_rcv_one_skb+0x1d/0x530 udp_unicast_rcv_skb+0x76/0x90 __udp4_lib_rcv+0xa64/0xe90 ip_protocol_deliver_rcu+0x20/0x130 ip_local_deliver_finish+0x75/0xa0 ip_local_deliver+0xc1/0xd0 ? ip_protocol_deliver_rcu+0x130/0x130 ip_sublist_rcv+0x1f9/0x240 ? ip_rcv_finish_core+0x430/0x430 ip_list_rcv+0xfc/0x130 __netif_receive_skb_list_core+0x181/0x1e0 netif_receive_skb_list_internal+0x200/0x360 ? mlx5e_build_rx_skb+0x1bc/0xda0 [mlx5_core] gro_receive_skb+0xfd/0x210 mlx5e_handle_rx_cqe_mpwrq+0x141/0x280 [mlx5_core] mlx5e_poll_rx_cq+0xcc/0x8e0 [mlx5_core] ? mlx5e_handle_rx_dim+0x91/0xd0 [mlx5_core] mlx5e_napi_poll+0x114/0xab0 [mlx5_core] __napi_poll+0x25/0x170 net_rx_action+0x32d/0x3a0 ? mlx5_eq_comp_int+0x8d/0x280 [mlx5_core] ? notifier_call_chain+0x33/0xa0 handle_softirqs+0xda/0x250 irq_exit_rcu+0x6d/0xc0 common_interrupt+0x81/0xa0 </IRQ>

In the Linux kernel, the following vulnerability has been resolved: neighbour: Fix null-ptr-deref in neigh_flush_dev(). kernel test robot reported null-ptr-deref in neigh_flush_dev(). [0] The cited commit introduced per-netdev neighbour list and converted neigh_flush_dev() to use it instead of the global hash table. One thing we missed is that neigh_table_clear() calls neigh_ifdown() with NULL dev. Let's restore the hash table iteration. Note that IPv6 module is no longer unloadable, so neigh_table_clear() is called only when IPv6 fails to initialise, which is unlikely to happen. [0]: IPv6: Attempt to unregister permanent protocol 136 IPv6: Attempt to unregister permanent protocol 17 Oops: general protection fault, probably for non-canonical address 0xdffffc00000001a0: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000d00-0x0000000000000d07] CPU: 1 UID: 0 PID: 1 Comm: systemd Tainted: G T 6.12.0-rc6-01246-gf7f52738637f #1 Tainted: [T]=RANDSTRUCT Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 RIP: 0010:neigh_flush_dev.llvm.6395807810224103582+0x52/0x570 Code: c1 e8 03 42 8a 04 38 84 c0 0f 85 15 05 00 00 31 c0 41 83 3e 0a 0f 94 c0 48 8d 1c c3 48 81 c3 f8 0c 00 00 48 89 d8 48 c1 e8 03 <42> 80 3c 38 00 74 08 48 89 df e8 f7 49 93 fe 4c 8b 3b 4d 85 ff 0f RSP: 0000:ffff88810026f408 EFLAGS: 00010206 RAX: 00000000000001a0 RBX: 0000000000000d00 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffc0631640 RBP: ffff88810026f470 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: ffffffffc0625250 R14: ffffffffc0631640 R15: dffffc0000000000 FS: 00007f575cb83940(0000) GS:ffff8883aee00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f575db40008 CR3: 00000002bf936000 CR4: 00000000000406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __neigh_ifdown.llvm.6395807810224103582+0x44/0x390 neigh_table_clear+0xb1/0x268 ndisc_cleanup+0x21/0x38 [ipv6] init_module+0x2f5/0x468 [ipv6] do_one_initcall+0x1ba/0x628 do_init_module+0x21a/0x530 load_module+0x2550/0x2ea0 __se_sys_finit_module+0x3d2/0x620 __x64_sys_finit_module+0x76/0x88 x64_sys_call+0x7ff/0xde8 do_syscall_64+0xfb/0x1e8 entry_SYSCALL_64_after_hwframe+0x67/0x6f RIP: 0033:0x7f575d6f2719 Code: 08 89 e8 5b 5d c3 66 2e 0f 1f 84 00 00 00 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d b7 06 0d 00 f7 d8 64 89 01 48 RSP: 002b:00007fff82a2a268 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 0000557827b45310 RCX: 00007f575d6f2719 RDX: 0000000000000000 RSI: 00007f575d584efd RDI: 0000000000000004 RBP: 00007f575d584efd R08: 0000000000000000 R09: 0000557827b47b00 R10: 0000000000000004 R11: 0000000000000246 R12: 0000000000020000 R13: 0000000000000000 R14: 0000557827b470e0 R15: 00007f575dbb4270 </TASK> Modules linked in: ipv6(+)

In the Linux kernel, the following vulnerability has been resolved: ipv6: prevent infinite loop in rt6_nlmsg_size() While testing prior patch, I was able to trigger an infinite loop in rt6_nlmsg_size() in the following place: list_for_each_entry_rcu(sibling, &f6i->fib6_siblings, fib6_siblings) { rt6_nh_nlmsg_size(sibling->fib6_nh, &nexthop_len); } This is because fib6_del_route() and fib6_add_rt2node() uses list_del_rcu(), which can confuse rcu readers, because they might no longer see the head of the list. Restart the loop if f6i->fib6_nsiblings is zero.

In the Linux kernel, the following vulnerability has been resolved: ipv6: fix possible infinite loop in fib6_info_uses_dev() fib6_info_uses_dev() seems to rely on RCU without an explicit protection. Like the prior fix in rt6_nlmsg_size(), we need to make sure fib6_del_route() or fib6_add_rt2node() have not removed the anchor from the list, or we risk an infinite loop.

In the Linux kernel, the following vulnerability has been resolved: bpf, arm64: Fix fp initialization for exception boundary In the ARM64 BPF JIT when prog->aux->exception_boundary is set for a BPF program, find_used_callee_regs() is not called because for a program acting as exception boundary, all callee saved registers are saved. find_used_callee_regs() sets `ctx->fp_used = true;` when it sees FP being used in any of the instructions. For programs acting as exception boundary, ctx->fp_used remains false even if frame pointer is used by the program and therefore, FP is not set-up for such programs in the prologue. This can cause the kernel to crash due to a pagefault. Fix it by setting ctx->fp_used = true for exception boundary programs as fp is always saved in such programs.

In the Linux kernel, the following vulnerability has been resolved: staging: media: atomisp: Fix stack buffer overflow in gmin_get_var_int() When gmin_get_config_var() calls efi.get_variable() and the EFI variable is larger than the expected buffer size, two behaviors combine to create a stack buffer overflow: 1. gmin_get_config_var() does not return the proper error code when efi.get_variable() fails. It returns the stale 'ret' value from earlier operations instead of indicating the EFI failure. 2. When efi.get_variable() returns EFI_BUFFER_TOO_SMALL, it updates *out_len to the required buffer size but writes no data to the output buffer. However, due to bug #1, gmin_get_var_int() believes the call succeeded. The caller gmin_get_var_int() then performs: - Allocates val[CFG_VAR_NAME_MAX + 1] (65 bytes) on stack - Calls gmin_get_config_var(dev, is_gmin, var, val, &len) with len=64 - If EFI variable is >64 bytes, efi.get_variable() sets len=required_size - Due to bug #1, thinks call succeeded with len=required_size - Executes val[len] = 0, writing past end of 65-byte stack buffer This creates a stack buffer overflow when EFI variables are larger than 64 bytes. Since EFI variables can be controlled by firmware or system configuration, this could potentially be exploited for code execution. Fix the bug by returning proper error codes from gmin_get_config_var() based on EFI status instead of stale 'ret' value. The gmin_get_var_int() function is called during device initialization for camera sensor configuration on Intel Bay Trail and Cherry Trail platforms using the atomisp camera stack.

In the Linux kernel, the following vulnerability has been resolved: padata: Fix pd UAF once and for all There is a race condition/UAF in padata_reorder that goes back to the initial commit. A reference count is taken at the start of the process in padata_do_parallel, and released at the end in padata_serial_worker. This reference count is (and only is) required for padata_replace to function correctly. If padata_replace is never called then there is no issue. In the function padata_reorder which serves as the core of padata, as soon as padata is added to queue->serial.list, and the associated spin lock released, that padata may be processed and the reference count on pd would go away. Fix this by getting the next padata before the squeue->serial lock is released. In order to make this possible, simplify padata_reorder by only calling it once the next padata arrives.

In the Linux kernel, the following vulnerability has been resolved: clk: xilinx: vcu: unregister pll_post only if registered correctly If registration of pll_post is failed, it will be set to NULL or ERR, unregistering same will fail with following call trace: Unable to handle kernel NULL pointer dereference at virtual address 008 pc : clk_hw_unregister+0xc/0x20 lr : clk_hw_unregister_fixed_factor+0x18/0x30 sp : ffff800011923850 ... Call trace: clk_hw_unregister+0xc/0x20 clk_hw_unregister_fixed_factor+0x18/0x30 xvcu_unregister_clock_provider+0xcc/0xf4 [xlnx_vcu] xvcu_probe+0x2bc/0x53c [xlnx_vcu]

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix double destruction of rsv_qp rsv_qp may be double destroyed in error flow, first in free_mr_init(), and then in hns_roce_exit(). Fix it by moving the free_mr_init() call into hns_roce_v2_init(). list_del corruption, ffff589732eb9b50->next is LIST_POISON1 (dead000000000100) WARNING: CPU: 8 PID: 1047115 at lib/list_debug.c:53 __list_del_entry_valid+0x148/0x240 ... Call trace: __list_del_entry_valid+0x148/0x240 hns_roce_qp_remove+0x4c/0x3f0 [hns_roce_hw_v2] hns_roce_v2_destroy_qp_common+0x1dc/0x5f4 [hns_roce_hw_v2] hns_roce_v2_destroy_qp+0x22c/0x46c [hns_roce_hw_v2] free_mr_exit+0x6c/0x120 [hns_roce_hw_v2] hns_roce_v2_exit+0x170/0x200 [hns_roce_hw_v2] hns_roce_exit+0x118/0x350 [hns_roce_hw_v2] __hns_roce_hw_v2_init_instance+0x1c8/0x304 [hns_roce_hw_v2] hns_roce_hw_v2_reset_notify_init+0x170/0x21c [hns_roce_hw_v2] hns_roce_hw_v2_reset_notify+0x6c/0x190 [hns_roce_hw_v2] hclge_notify_roce_client+0x6c/0x160 [hclge] hclge_reset_rebuild+0x150/0x5c0 [hclge] hclge_reset+0x10c/0x140 [hclge] hclge_reset_subtask+0x80/0x104 [hclge] hclge_reset_service_task+0x168/0x3ac [hclge] hclge_service_task+0x50/0x100 [hclge] process_one_work+0x250/0x9a0 worker_thread+0x324/0x990 kthread+0x190/0x210 ret_from_fork+0x10/0x18

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp - Fix crash when rebind ccp device for ccp.ko When CONFIG_CRYPTO_DEV_CCP_DEBUGFS is enabled, rebinding the ccp device causes the following crash: $ echo '0000:0a:00.2' > /sys/bus/pci/drivers/ccp/unbind $ echo '0000:0a:00.2' > /sys/bus/pci/drivers/ccp/bind [ 204.976930] BUG: kernel NULL pointer dereference, address: 0000000000000098 [ 204.978026] #PF: supervisor write access in kernel mode [ 204.979126] #PF: error_code(0x0002) - not-present page [ 204.980226] PGD 0 P4D 0 [ 204.981317] Oops: Oops: 0002 [#1] SMP NOPTI ... [ 204.997852] Call Trace: [ 204.999074] <TASK> [ 205.000297] start_creating+0x9f/0x1c0 [ 205.001533] debugfs_create_dir+0x1f/0x170 [ 205.002769] ? srso_return_thunk+0x5/0x5f [ 205.004000] ccp5_debugfs_setup+0x87/0x170 [ccp] [ 205.005241] ccp5_init+0x8b2/0x960 [ccp] [ 205.006469] ccp_dev_init+0xd4/0x150 [ccp] [ 205.007709] sp_init+0x5f/0x80 [ccp] [ 205.008942] sp_pci_probe+0x283/0x2e0 [ccp] [ 205.010165] ? srso_return_thunk+0x5/0x5f [ 205.011376] local_pci_probe+0x4f/0xb0 [ 205.012584] pci_device_probe+0xdb/0x230 [ 205.013810] really_probe+0xed/0x380 [ 205.015024] __driver_probe_device+0x7e/0x160 [ 205.016240] device_driver_attach+0x2f/0x60 [ 205.017457] bind_store+0x7c/0xb0 [ 205.018663] drv_attr_store+0x28/0x40 [ 205.019868] sysfs_kf_write+0x5f/0x70 [ 205.021065] kernfs_fop_write_iter+0x145/0x1d0 [ 205.022267] vfs_write+0x308/0x440 [ 205.023453] ksys_write+0x6d/0xe0 [ 205.024616] __x64_sys_write+0x1e/0x30 [ 205.025778] x64_sys_call+0x16ba/0x2150 [ 205.026942] do_syscall_64+0x56/0x1e0 [ 205.028108] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 205.029276] RIP: 0033:0x7fbc36f10104 [ 205.030420] Code: 89 02 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 8d 05 e1 08 2e 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 f3 c3 66 90 41 54 55 49 89 d4 53 48 89 f5 This patch sets ccp_debugfs_dir to NULL after destroying it in ccp5_debugfs_destroy, allowing the directory dentry to be recreated when rebinding the ccp device. Tested on AMD Ryzen 7 1700X.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix inode use after free in ext4_end_io_rsv_work() In ext4_io_end_defer_completion(), check if io_end->list_vec is empty to avoid adding an io_end that requires no conversion to the i_rsv_conversion_list, which in turn prevents starting an unnecessary worker. An ext4_emergency_state() check is also added to avoid attempting to abort the journal in an emergency state. Additionally, ext4_put_io_end_defer() is refactored to call ext4_io_end_defer_completion() directly instead of being open-coded. This also prevents starting an unnecessary worker when EXT4_IO_END_FAILED is set but data_err=abort is not enabled. This ensures that the check in ext4_put_io_end_defer() is consistent with the check in ext4_end_bio(). Otherwise, we might add an io_end to the i_rsv_conversion_list and then call ext4_finish_bio(), after which the inode could be freed before ext4_end_io_rsv_work() is called, triggering a use-after-free issue.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix KMSAN uninit-value in extent_info usage KMSAN reported a use of uninitialized value in `__is_extent_mergeable()` and `__is_back_mergeable()` via the read extent tree path. The root cause is that `get_read_extent_info()` only initializes three fields (`fofs`, `blk`, `len`) of `struct extent_info`, leaving the remaining fields uninitialized. This leads to undefined behavior when those fields are accessed later, especially during extent merging. Fix it by zero-initializing the `extent_info` struct before population.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid UAF in f2fs_sync_inode_meta() syzbot reported an UAF issue as below: [1] [2] [1] https://syzkaller.appspot.com/text?tag=CrashReport&x=16594c60580000 ================================================================== BUG: KASAN: use-after-free in __list_del_entry_valid+0xa6/0x130 lib/list_debug.c:62 Read of size 8 at addr ffff888100567dc8 by task kworker/u4:0/8 CPU: 1 PID: 8 Comm: kworker/u4:0 Tainted: G W 6.1.129-syzkaller-00017-g642656a36791 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Workqueue: writeback wb_workfn (flush-7:0) Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x151/0x1b7 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:316 [inline] print_report+0x158/0x4e0 mm/kasan/report.c:427 kasan_report+0x13c/0x170 mm/kasan/report.c:531 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report_generic.c:351 __list_del_entry_valid+0xa6/0x130 lib/list_debug.c:62 __list_del_entry include/linux/list.h:134 [inline] list_del_init include/linux/list.h:206 [inline] f2fs_inode_synced+0x100/0x2e0 fs/f2fs/super.c:1553 f2fs_update_inode+0x72/0x1c40 fs/f2fs/inode.c:588 f2fs_update_inode_page+0x135/0x170 fs/f2fs/inode.c:706 f2fs_write_inode+0x416/0x790 fs/f2fs/inode.c:734 write_inode fs/fs-writeback.c:1460 [inline] __writeback_single_inode+0x4cf/0xb80 fs/fs-writeback.c:1677 writeback_sb_inodes+0xb32/0x1910 fs/fs-writeback.c:1903 __writeback_inodes_wb+0x118/0x3f0 fs/fs-writeback.c:1974 wb_writeback+0x3da/0xa00 fs/fs-writeback.c:2081 wb_check_background_flush fs/fs-writeback.c:2151 [inline] wb_do_writeback fs/fs-writeback.c:2239 [inline] wb_workfn+0xbba/0x1030 fs/fs-writeback.c:2266 process_one_work+0x73d/0xcb0 kernel/workqueue.c:2299 worker_thread+0xa60/0x1260 kernel/workqueue.c:2446 kthread+0x26d/0x300 kernel/kthread.c:386 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295 </TASK> Allocated by task 298: kasan_save_stack mm/kasan/common.c:45 [inline] kasan_set_track+0x4b/0x70 mm/kasan/common.c:52 kasan_save_alloc_info+0x1f/0x30 mm/kasan/generic.c:505 __kasan_slab_alloc+0x6c/0x80 mm/kasan/common.c:333 kasan_slab_alloc include/linux/kasan.h:202 [inline] slab_post_alloc_hook+0x53/0x2c0 mm/slab.h:768 slab_alloc_node mm/slub.c:3421 [inline] slab_alloc mm/slub.c:3431 [inline] __kmem_cache_alloc_lru mm/slub.c:3438 [inline] kmem_cache_alloc_lru+0x102/0x270 mm/slub.c:3454 alloc_inode_sb include/linux/fs.h:3255 [inline] f2fs_alloc_inode+0x2d/0x350 fs/f2fs/super.c:1437 alloc_inode fs/inode.c:261 [inline] iget_locked+0x18c/0x7e0 fs/inode.c:1373 f2fs_iget+0x55/0x4ca0 fs/f2fs/inode.c:486 f2fs_lookup+0x3c1/0xb50 fs/f2fs/namei.c:484 __lookup_slow+0x2b9/0x3e0 fs/namei.c:1689 lookup_slow+0x5a/0x80 fs/namei.c:1706 walk_component+0x2e7/0x410 fs/namei.c:1997 lookup_last fs/namei.c:2454 [inline] path_lookupat+0x16d/0x450 fs/namei.c:2478 filename_lookup+0x251/0x600 fs/namei.c:2507 vfs_statx+0x107/0x4b0 fs/stat.c:229 vfs_fstatat fs/stat.c:267 [inline] vfs_lstat include/linux/fs.h:3434 [inline] __do_sys_newlstat fs/stat.c:423 [inline] __se_sys_newlstat+0xda/0x7c0 fs/stat.c:417 __x64_sys_newlstat+0x5b/0x70 fs/stat.c:417 x64_sys_call+0x52/0x9a0 arch/x86/include/generated/asm/syscalls_64.h:7 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x3b/0x80 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x68/0xd2 Freed by task 0: kasan_save_stack mm/kasan/common.c:45 [inline] kasan_set_track+0x4b/0x70 mm/kasan/common.c:52 kasan_save_free_info+0x2b/0x40 mm/kasan/generic.c:516 ____kasan_slab_free+0x131/0x180 mm/kasan/common.c:241 __kasan_slab_free+0x11/0x20 mm/kasan/common.c:249 kasan_slab_free include/linux/kasan.h:178 [inline] slab_free_hook mm/slub.c:1745 [inline] slab_free_freelist_hook mm/slub.c:1771 [inline] slab_free mm/slub.c:3686 [inline] kmem_cache_free+0x ---truncated---

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid panic in f2fs_evict_inode As syzbot [1] reported as below: R10: 0000000000000100 R11: 0000000000000206 R12: 00007ffe17473450 R13: 00007f28b1c10854 R14: 000000000000dae5 R15: 00007ffe17474520 </TASK> ---[ end trace 0000000000000000 ]--- ================================================================== BUG: KASAN: use-after-free in __list_del_entry_valid+0xa6/0x130 lib/list_debug.c:62 Read of size 8 at addr ffff88812d962278 by task syz-executor/564 CPU: 1 PID: 564 Comm: syz-executor Tainted: G W 6.1.129-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Call Trace: <TASK> __dump_stack+0x21/0x24 lib/dump_stack.c:88 dump_stack_lvl+0xee/0x158 lib/dump_stack.c:106 print_address_description+0x71/0x210 mm/kasan/report.c:316 print_report+0x4a/0x60 mm/kasan/report.c:427 kasan_report+0x122/0x150 mm/kasan/report.c:531 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report_generic.c:351 __list_del_entry_valid+0xa6/0x130 lib/list_debug.c:62 __list_del_entry include/linux/list.h:134 [inline] list_del_init include/linux/list.h:206 [inline] f2fs_inode_synced+0xf7/0x2e0 fs/f2fs/super.c:1531 f2fs_update_inode+0x74/0x1c40 fs/f2fs/inode.c:585 f2fs_update_inode_page+0x137/0x170 fs/f2fs/inode.c:703 f2fs_write_inode+0x4ec/0x770 fs/f2fs/inode.c:731 write_inode fs/fs-writeback.c:1460 [inline] __writeback_single_inode+0x4a0/0xab0 fs/fs-writeback.c:1677 writeback_single_inode+0x221/0x8b0 fs/fs-writeback.c:1733 sync_inode_metadata+0xb6/0x110 fs/fs-writeback.c:2789 f2fs_sync_inode_meta+0x16d/0x2a0 fs/f2fs/checkpoint.c:1159 block_operations fs/f2fs/checkpoint.c:1269 [inline] f2fs_write_checkpoint+0xca3/0x2100 fs/f2fs/checkpoint.c:1658 kill_f2fs_super+0x231/0x390 fs/f2fs/super.c:4668 deactivate_locked_super+0x98/0x100 fs/super.c:332 deactivate_super+0xaf/0xe0 fs/super.c:363 cleanup_mnt+0x45f/0x4e0 fs/namespace.c:1186 __cleanup_mnt+0x19/0x20 fs/namespace.c:1193 task_work_run+0x1c6/0x230 kernel/task_work.c:203 exit_task_work include/linux/task_work.h:39 [inline] do_exit+0x9fb/0x2410 kernel/exit.c:871 do_group_exit+0x210/0x2d0 kernel/exit.c:1021 __do_sys_exit_group kernel/exit.c:1032 [inline] __se_sys_exit_group kernel/exit.c:1030 [inline] __x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1030 x64_sys_call+0x7b4/0x9a0 arch/x86/include/generated/asm/syscalls_64.h:232 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x4c/0xa0 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x68/0xd2 RIP: 0033:0x7f28b1b8e169 Code: Unable to access opcode bytes at 0x7f28b1b8e13f. RSP: 002b:00007ffe174710a8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 RAX: ffffffffffffffda RBX: 00007f28b1c10879 RCX: 00007f28b1b8e169 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000001 RBP: 0000000000000002 R08: 00007ffe1746ee47 R09: 00007ffe17472360 R10: 0000000000000009 R11: 0000000000000246 R12: 00007ffe17472360 R13: 00007f28b1c10854 R14: 000000000000dae5 R15: 00007ffe17474520 </TASK> Allocated by task 569: kasan_save_stack mm/kasan/common.c:45 [inline] kasan_set_track+0x4b/0x70 mm/kasan/common.c:52 kasan_save_alloc_info+0x25/0x30 mm/kasan/generic.c:505 __kasan_slab_alloc+0x72/0x80 mm/kasan/common.c:328 kasan_slab_alloc include/linux/kasan.h:201 [inline] slab_post_alloc_hook+0x4f/0x2c0 mm/slab.h:737 slab_alloc_node mm/slub.c:3398 [inline] slab_alloc mm/slub.c:3406 [inline] __kmem_cache_alloc_lru mm/slub.c:3413 [inline] kmem_cache_alloc_lru+0x104/0x220 mm/slub.c:3429 alloc_inode_sb include/linux/fs.h:3245 [inline] f2fs_alloc_inode+0x2d/0x340 fs/f2fs/super.c:1419 alloc_inode fs/inode.c:261 [inline] iget_locked+0x186/0x880 fs/inode.c:1373 f2fs_iget+0x55/0x4c60 fs/f2fs/inode.c:483 f2fs_lookup+0x366/0xab0 fs/f2fs/namei.c:487 __lookup_slow+0x2a3/0x3d0 fs/namei.c:1690 lookup_slow+0x57/0x70 fs/namei.c:1707 walk_component+0x2e6/0x410 fs/namei ---truncated---