In the Linux kernel, the following vulnerability has been resolved: PCI/DPC: Fix use-after-free on concurrent DPC and hot-removal Keith reports a use-after-free when a DPC event occurs concurrently to hot-removal of the same portion of the hierarchy: The dpc_handler() awaits readiness of the secondary bus below the Downstream Port where the DPC event occurred. To do so, it polls the config space of the first child device on the secondary bus. If that child device is concurrently removed, accesses to its struct pci_dev cause the kernel to oops. That's because pci_bridge_wait_for_secondary_bus() neglects to hold a reference on the child device. Before v6.3, the function was only called on resume from system sleep or on runtime resume. Holding a reference wasn't necessary back then because the pciehp IRQ thread could never run concurrently. (On resume from system sleep, IRQs are not enabled until after the resume_noirq phase. And runtime resume is always awaited before a PCI device is removed.) However starting with v6.3, pci_bridge_wait_for_secondary_bus() is also called on a DPC event. Commit 53b54ad074de ("PCI/DPC: Await readiness of secondary bus after reset"), which introduced that, failed to appreciate that pci_bridge_wait_for_secondary_bus() now needs to hold a reference on the child device because dpc_handler() and pciehp may indeed run concurrently. The commit was backported to v5.10+ stable kernels, so that's the oldest one affected. Add the missing reference acquisition. Abridged stack trace: BUG: unable to handle page fault for address: 00000000091400c0 CPU: 15 PID: 2464 Comm: irq/53-pcie-dpc 6.9.0 RIP: pci_bus_read_config_dword+0x17/0x50 pci_dev_wait() pci_bridge_wait_for_secondary_bus() dpc_reset_link() pcie_do_recovery() dpc_handler()

In the Linux kernel, the following vulnerability has been resolved: iio: chemical: bme680: Fix overflows in compensate() functions There are cases in the compensate functions of the driver that there could be overflows of variables due to bit shifting ops. These implications were initially discussed here [1] and they were mentioned in log message of Commit 1b3bd8592780 ("iio: chemical: Add support for Bosch BME680 sensor"). [1]: https://lore.kernel.org/linux-iio/20180728114028.3c1bbe81@archlinux/

In the Linux kernel, the following vulnerability has been resolved: ext4: use memtostr_pad() for s_volume_name As with the other strings in struct ext4_super_block, s_volume_name is not NUL terminated. The other strings were marked in commit 072ebb3bffe6 ("ext4: add nonstring annotations to ext4.h"). Using strscpy() isn't the right replacement for strncpy(); it should use memtostr_pad() instead.

In the Linux kernel, the following vulnerability has been resolved: gpio: davinci: Validate the obtained number of IRQs Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken DT due to any error this value can be any. Without this value validation there can be out of chips->irqs array boundaries access in davinci_gpio_probe(). Validate the obtained nirq value so that it won't exceed the maximum number of IRQs per bank. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: mt8195: Add platform entry for ETDM1_OUT_BE dai link Commit e70b8dd26711 ("ASoC: mediatek: mt8195: Remove afe-dai component and rework codec link") removed the codec entry for the ETDM1_OUT_BE dai link entirely instead of replacing it with COMP_EMPTY(). This worked by accident as the remaining COMP_EMPTY() platform entry became the codec entry, and the platform entry became completely empty, effectively the same as COMP_DUMMY() since snd_soc_fill_dummy_dai() doesn't do anything for platform entries. This causes a KASAN out-of-bounds warning in mtk_soundcard_common_probe() in sound/soc/mediatek/common/mtk-soundcard-driver.c: for_each_card_prelinks(card, i, dai_link) { if (adsp_node && !strncmp(dai_link->name, "AFE_SOF", strlen("AFE_SOF"))) dai_link->platforms->of_node = adsp_node; else if (!dai_link->platforms->name && !dai_link->platforms->of_node) dai_link->platforms->of_node = platform_node; } where the code expects the platforms array to have space for at least one entry. Add an COMP_EMPTY() entry so that dai_link->platforms has space.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check index msg_id before read or write [WHAT] msg_id is used as an array index and it cannot be a negative value, and therefore cannot be equal to MOD_HDCP_MESSAGE_ID_INVALID (-1). [HOW] Check whether msg_id is valid before reading and setting. This fixes 4 OVERRUN issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Skip finding free audio for unknown engine_id [WHY] ENGINE_ID_UNKNOWN = -1 and can not be used as an array index. Plus, it also means it is uninitialized and does not need free audio. [HOW] Skip and return NULL. This fixes 2 OVERRUN issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check pipe offset before setting vblank pipe_ctx has a size of MAX_PIPES so checking its index before accessing the array. This fixes an OVERRUN issue reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: dev/parport: fix the array out-of-bounds risk Fixed array out-of-bounds issues caused by sprintf by replacing it with snprintf for safer data copying, ensuring the destination buffer is not overflowed. Below is the stack trace I encountered during the actual issue: [ 66.575408s] [pid:5118,cpu4,QThread,4]Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: do_hardware_base_addr+0xcc/0xd0 [parport] [ 66.575408s] [pid:5118,cpu4,QThread,5]CPU: 4 PID: 5118 Comm: QThread Tainted: G S W O 5.10.97-arm64-desktop #7100.57021.2 [ 66.575439s] [pid:5118,cpu4,QThread,6]TGID: 5087 Comm: EFileApp [ 66.575439s] [pid:5118,cpu4,QThread,7]Hardware name: HUAWEI HUAWEI QingYun PGUX-W515x-B081/SP1PANGUXM, BIOS 1.00.07 04/29/2024 [ 66.575439s] [pid:5118,cpu4,QThread,8]Call trace: [ 66.575469s] [pid:5118,cpu4,QThread,9] dump_backtrace+0x0/0x1c0 [ 66.575469s] [pid:5118,cpu4,QThread,0] show_stack+0x14/0x20 [ 66.575469s] [pid:5118,cpu4,QThread,1] dump_stack+0xd4/0x10c [ 66.575500s] [pid:5118,cpu4,QThread,2] panic+0x1d8/0x3bc [ 66.575500s] [pid:5118,cpu4,QThread,3] __stack_chk_fail+0x2c/0x38 [ 66.575500s] [pid:5118,cpu4,QThread,4] do_hardware_base_addr+0xcc/0xd0 [parport]

In the Linux kernel, the following vulnerability has been resolved: scsi: mpi3mr: Sanitise num_phys Information is stored in mr_sas_port->phy_mask, values larger then size of this field shouldn't be allowed.

In the Linux kernel, the following vulnerability has been resolved: tipc: Return non-zero value from tipc_udp_addr2str() on error tipc_udp_addr2str() should return non-zero value if the UDP media address is invalid. Otherwise, a buffer overflow access can occur in tipc_media_addr_printf(). Fix this by returning 1 on an invalid UDP media address.

In the Linux kernel, the following vulnerability has been resolved: bnx2x: Fix multiple UBSAN array-index-out-of-bounds Fix UBSAN warnings that occur when using a system with 32 physical cpu cores or more, or when the user defines a number of Ethernet queues greater than or equal to FP_SB_MAX_E1x using the num_queues module parameter. Currently there is a read/write out of bounds that occurs on the array "struct stats_query_entry query" present inside the "bnx2x_fw_stats_req" struct in "drivers/net/ethernet/broadcom/bnx2x/bnx2x.h". Looking at the definition of the "struct stats_query_entry query" array: struct stats_query_entry query[FP_SB_MAX_E1x+ BNX2X_FIRST_QUEUE_QUERY_IDX]; FP_SB_MAX_E1x is defined as the maximum number of fast path interrupts and has a value of 16, while BNX2X_FIRST_QUEUE_QUERY_IDX has a value of 3 meaning the array has a total size of 19. Since accesses to "struct stats_query_entry query" are offset-ted by BNX2X_FIRST_QUEUE_QUERY_IDX, that means that the total number of Ethernet queues should not exceed FP_SB_MAX_E1x (16). However one of these queues is reserved for FCOE and thus the number of Ethernet queues should be set to [FP_SB_MAX_E1x -1] (15) if FCOE is enabled or [FP_SB_MAX_E1x] (16) if it is not. This is also described in a comment in the source code in drivers/net/ethernet/broadcom/bnx2x/bnx2x.h just above the Macro definition of FP_SB_MAX_E1x. Below is the part of this explanation that it important for this patch /* * The total number of L2 queues, MSIX vectors and HW contexts (CIDs) is * control by the number of fast-path status blocks supported by the * device (HW/FW). Each fast-path status block (FP-SB) aka non-default * status block represents an independent interrupts context that can * serve a regular L2 networking queue. However special L2 queues such * as the FCoE queue do not require a FP-SB and other components like * the CNIC may consume FP-SB reducing the number of possible L2 queues * * If the maximum number of FP-SB available is X then: * a. If CNIC is supported it consumes 1 FP-SB thus the max number of * regular L2 queues is Y=X-1 * b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor) * c. If the FCoE L2 queue is supported the actual number of L2 queues * is Y+1 * d. The number of irqs (MSIX vectors) is either Y+1 (one extra for * slow-path interrupts) or Y+2 if CNIC is supported (one additional * FP interrupt context for the CNIC). * e. The number of HW context (CID count) is always X or X+1 if FCoE * L2 queue is supported. The cid for the FCoE L2 queue is always X. */ However this driver also supports NICs that use the E2 controller which can handle more queues due to having more FP-SB represented by FP_SB_MAX_E2. Looking at the commits when the E2 support was added, it was originally using the E1x parameters: commit f2e0899f0f27 ("bnx2x: Add 57712 support"). Back then FP_SB_MAX_E2 was set to 16 the same as E1x. However the driver was later updated to take full advantage of the E2 instead of having it be limited to the capabilities of the E1x. But as far as we can tell, the array "stats_query_entry query" was still limited to using the FP-SB available to the E1x cards as part of an oversignt when the driver was updated to take full advantage of the E2, and now with the driver being aware of the greater queue size supported by E2 NICs, it causes the UBSAN warnings seen in the stack traces below. This patch increases the size of the "stats_query_entry query" array by replacing FP_SB_MAX_E1x with FP_SB_MAX_E2 to be large enough to handle both types of NICs. Stack traces: UBSAN: array-index-out-of-bounds in drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1529:11 index 20 is out of range for type 'stats_query_entry [19]' CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic #202405052133 Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix extent map use-after-free when adding pages to compressed bio At add_ra_bio_pages() we are accessing the extent map to calculate 'add_size' after we dropped our reference on the extent map, resulting in a use-after-free. Fix this by computing 'add_size' before dropping our extent map reference.

In the Linux kernel, the following vulnerability has been resolved: net/iucv: fix use after free in iucv_sock_close() iucv_sever_path() is called from process context and from bh context. iucv->path is used as indicator whether somebody else is taking care of severing the path (or it is already removed / never existed). This needs to be done with atomic compare and swap, otherwise there is a small window where iucv_sock_close() will try to work with a path that has already been severed and freed by iucv_callback_connrej() called by iucv_tasklet_fn(). Example: [452744.123844] Call Trace: [452744.123845] ([<0000001e87f03880>] 0x1e87f03880) [452744.123966] [<00000000d593001e>] iucv_path_sever+0x96/0x138 [452744.124330] [<000003ff801ddbca>] iucv_sever_path+0xc2/0xd0 [af_iucv] [452744.124336] [<000003ff801e01b6>] iucv_sock_close+0xa6/0x310 [af_iucv] [452744.124341] [<000003ff801e08cc>] iucv_sock_release+0x3c/0xd0 [af_iucv] [452744.124345] [<00000000d574794e>] __sock_release+0x5e/0xe8 [452744.124815] [<00000000d5747a0c>] sock_close+0x34/0x48 [452744.124820] [<00000000d5421642>] __fput+0xba/0x268 [452744.124826] [<00000000d51b382c>] task_work_run+0xbc/0xf0 [452744.124832] [<00000000d5145710>] do_notify_resume+0x88/0x90 [452744.124841] [<00000000d5978096>] system_call+0xe2/0x2c8 [452744.125319] Last Breaking-Event-Address: [452744.125321] [<00000000d5930018>] iucv_path_sever+0x90/0x138 [452744.125324] [452744.125325] Kernel panic - not syncing: Fatal exception in interrupt Note that bh_lock_sock() is not serializing the tasklet context against process context, because the check for sock_owned_by_user() and corresponding handling is missing. Ideas for a future clean-up patch: A) Correct usage of bh_lock_sock() in tasklet context, as described in Re-enqueue, if needed. This may require adding return values to the tasklet functions and thus changes to all users of iucv. B) Change iucv tasklet into worker and use only lock_sock() in af_iucv.

In the Linux kernel, the following vulnerability has been resolved: net: txgbe: free isb resources at the right time When using MSI/INTx interrupt, the shared interrupts are still being handled in the device remove routine, before free IRQs. So isb memory is still read after it is freed. Thus move wx_free_isb_resources() from txgbe_close() to txgbe_remove(). And fix the improper isb free action in txgbe_open() error handling path.

In the Linux kernel, the following vulnerability has been resolved: cdrom: rearrange last_media_change check to avoid unintentional overflow When running syzkaller with the newly reintroduced signed integer wrap sanitizer we encounter this splat: [ 366.015950] UBSAN: signed-integer-overflow in ../drivers/cdrom/cdrom.c:2361:33 [ 366.021089] -9223372036854775808 - 346321 cannot be represented in type '__s64' (aka 'long long') [ 366.025894] program syz-executor.4 is using a deprecated SCSI ioctl, please convert it to SG_IO [ 366.027502] CPU: 5 PID: 28472 Comm: syz-executor.7 Not tainted 6.8.0-rc2-00035-gb3ef86b5a957 #1 [ 366.027512] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 366.027518] Call Trace: [ 366.027523] <TASK> [ 366.027533] dump_stack_lvl+0x93/0xd0 [ 366.027899] handle_overflow+0x171/0x1b0 [ 366.038787] ata1.00: invalid multi_count 32 ignored [ 366.043924] cdrom_ioctl+0x2c3f/0x2d10 [ 366.063932] ? __pm_runtime_resume+0xe6/0x130 [ 366.071923] sr_block_ioctl+0x15d/0x1d0 [ 366.074624] ? __pfx_sr_block_ioctl+0x10/0x10 [ 366.077642] blkdev_ioctl+0x419/0x500 [ 366.080231] ? __pfx_blkdev_ioctl+0x10/0x10 ... Historically, the signed integer overflow sanitizer did not work in the kernel due to its interaction with `-fwrapv` but this has since been changed [1] in the newest version of Clang. It was re-enabled in the kernel with Commit 557f8c582a9ba8ab ("ubsan: Reintroduce signed overflow sanitizer"). Let's rearrange the check to not perform any arithmetic, thus not tripping the sanitizer.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Do not return negative stream id for array [WHY] resource_stream_to_stream_idx returns an array index and it return -1 when not found; however, -1 is not a valid array index number. [HOW] When this happens, call ASSERT(), and return a zero instead. This fixes an OVERRUN and an NEGATIVE_RETURNS issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: RDMA/iwcm: Fix a use-after-free related to destroying CM IDs iw_conn_req_handler() associates a new struct rdma_id_private (conn_id) with an existing struct iw_cm_id (cm_id) as follows: conn_id->cm_id.iw = cm_id; cm_id->context = conn_id; cm_id->cm_handler = cma_iw_handler; rdma_destroy_id() frees both the cm_id and the struct rdma_id_private. Make sure that cm_work_handler() does not trigger a use-after-free by only freeing of the struct rdma_id_private after all pending work has finished.

In the Linux kernel, the following vulnerability has been resolved: mISDN: Fix a use after free in hfcmulti_tx() Don't dereference *sp after calling dev_kfree_skb(*sp).

In the Linux kernel, the following vulnerability has been resolved: platform/x86: toshiba_acpi: Fix array out-of-bounds access In order to use toshiba_dmi_quirks[] together with the standard DMI matching functions, it must be terminated by a empty entry. Since this entry is missing, an array out-of-bounds access occurs every time the quirk list is processed. Fix this by adding the terminating empty entry.

In the Linux kernel, the following vulnerability has been resolved: net: do not leave a dangling sk pointer, when socket creation fails It is possible to trigger a use-after-free by: * attaching an fentry probe to __sock_release() and the probe calling the bpf_get_socket_cookie() helper * running traceroute -I 1.1.1.1 on a freshly booted VM A KASAN enabled kernel will log something like below (decoded and stripped): ================================================================== BUG: KASAN: slab-use-after-free in __sock_gen_cookie (./arch/x86/include/asm/atomic64_64.h:15 ./include/linux/atomic/atomic-arch-fallback.h:2583 ./include/linux/atomic/atomic-instrumented.h:1611 net/core/sock_diag.c:29) Read of size 8 at addr ffff888007110dd8 by task traceroute/299 CPU: 2 PID: 299 Comm: traceroute Tainted: G E 6.10.0-rc2+ #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:117 (discriminator 1)) print_report (mm/kasan/report.c:378 mm/kasan/report.c:488) ? __sock_gen_cookie (./arch/x86/include/asm/atomic64_64.h:15 ./include/linux/atomic/atomic-arch-fallback.h:2583 ./include/linux/atomic/atomic-instrumented.h:1611 net/core/sock_diag.c:29) kasan_report (mm/kasan/report.c:603) ? __sock_gen_cookie (./arch/x86/include/asm/atomic64_64.h:15 ./include/linux/atomic/atomic-arch-fallback.h:2583 ./include/linux/atomic/atomic-instrumented.h:1611 net/core/sock_diag.c:29) kasan_check_range (mm/kasan/generic.c:183 mm/kasan/generic.c:189) __sock_gen_cookie (./arch/x86/include/asm/atomic64_64.h:15 ./include/linux/atomic/atomic-arch-fallback.h:2583 ./include/linux/atomic/atomic-instrumented.h:1611 net/core/sock_diag.c:29) bpf_get_socket_ptr_cookie (./arch/x86/include/asm/preempt.h:94 ./include/linux/sock_diag.h:42 net/core/filter.c:5094 net/core/filter.c:5092) bpf_prog_875642cf11f1d139___sock_release+0x6e/0x8e bpf_trampoline_6442506592+0x47/0xaf __sock_release (net/socket.c:652) __sock_create (net/socket.c:1601) ... Allocated by task 299 on cpu 2 at 78.328492s: kasan_save_stack (mm/kasan/common.c:48) kasan_save_track (mm/kasan/common.c:68) __kasan_slab_alloc (mm/kasan/common.c:312 mm/kasan/common.c:338) kmem_cache_alloc_noprof (mm/slub.c:3941 mm/slub.c:4000 mm/slub.c:4007) sk_prot_alloc (net/core/sock.c:2075) sk_alloc (net/core/sock.c:2134) inet_create (net/ipv4/af_inet.c:327 net/ipv4/af_inet.c:252) __sock_create (net/socket.c:1572) __sys_socket (net/socket.c:1660 net/socket.c:1644 net/socket.c:1706) __x64_sys_socket (net/socket.c:1718) do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Freed by task 299 on cpu 2 at 78.328502s: kasan_save_stack (mm/kasan/common.c:48) kasan_save_track (mm/kasan/common.c:68) kasan_save_free_info (mm/kasan/generic.c:582) poison_slab_object (mm/kasan/common.c:242) __kasan_slab_free (mm/kasan/common.c:256) kmem_cache_free (mm/slub.c:4437 mm/slub.c:4511) __sk_destruct (net/core/sock.c:2117 net/core/sock.c:2208) inet_create (net/ipv4/af_inet.c:397 net/ipv4/af_inet.c:252) __sock_create (net/socket.c:1572) __sys_socket (net/socket.c:1660 net/socket.c:1644 net/socket.c:1706) __x64_sys_socket (net/socket.c:1718) do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Fix this by clearing the struct socket reference in sk_common_release() to cover all protocol families create functions, which may already attached the reference to the sk object with sock_init_data().

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: lantiq_etop: fix double free in detach The number of the currently released descriptor is never incremented which results in the same skb being released multiple times.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: Set object to close if ondemand_id < 0 in copen If copen is maliciously called in the user mode, it may delete the request corresponding to the random id. And the request may have not been read yet. Note that when the object is set to reopen, the open request will be done with the still reopen state in above case. As a result, the request corresponding to this object is always skipped in select_req function, so the read request is never completed and blocks other process. Fix this issue by simply set object to close if its id < 0 in copen.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: cyclic allocation of msg_id to avoid reuse Reusing the msg_id after a maliciously completed reopen request may cause a read request to remain unprocessed and result in a hung, as shown below: t1 | t2 | t3 ------------------------------------------------- cachefiles_ondemand_select_req cachefiles_ondemand_object_is_close(A) cachefiles_ondemand_set_object_reopening(A) queue_work(fscache_object_wq, &info->work) ondemand_object_worker cachefiles_ondemand_init_object(A) cachefiles_ondemand_send_req(OPEN) // get msg_id 6 wait_for_completion(&req_A->done) cachefiles_ondemand_daemon_read // read msg_id 6 req_A cachefiles_ondemand_get_fd copy_to_user // Malicious completion msg_id 6 copen 6,-1 cachefiles_ondemand_copen complete(&req_A->done) // will not set the object to close // because ondemand_id && fd is valid. // ondemand_object_worker() is done // but the object is still reopening. // new open req_B cachefiles_ondemand_init_object(B) cachefiles_ondemand_send_req(OPEN) // reuse msg_id 6 process_open_req copen 6,A.size // The expected failed copen was executed successfully Expect copen to fail, and when it does, it closes fd, which sets the object to close, and then close triggers reopen again. However, due to msg_id reuse resulting in a successful copen, the anonymous fd is not closed until the daemon exits. Therefore read requests waiting for reopen to complete may trigger hung task. To avoid this issue, allocate the msg_id cyclically to avoid reusing the msg_id for a very short duration of time.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: fix use-after-free case in tcpm_register_source_caps There could be a potential use-after-free case in tcpm_register_source_caps(). This could happen when: * new (say invalid) source caps are advertised * the existing source caps are unregistered * tcpm_register_source_caps() returns with an error as usb_power_delivery_register_capabilities() fails This causes port->partner_source_caps to hold on to the now freed source caps. Reset port->partner_source_caps value to NULL after unregistering existing source caps.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpt3sas: Avoid test/set_bit() operating in non-allocated memory There is a potential out-of-bounds access when using test_bit() on a single word. The test_bit() and set_bit() functions operate on long values, and when testing or setting a single word, they can exceed the word boundary. KASAN detects this issue and produces a dump: BUG: KASAN: slab-out-of-bounds in _scsih_add_device.constprop.0 (./arch/x86/include/asm/bitops.h:60 ./include/asm-generic/bitops/instrumented-atomic.h:29 drivers/scsi/mpt3sas/mpt3sas_scsih.c:7331) mpt3sas Write of size 8 at addr ffff8881d26e3c60 by task kworker/u1536:2/2965 For full log, please look at [1]. Make the allocation at least the size of sizeof(unsigned long) so that set_bit() and test_bit() have sufficient room for read/write operations without overwriting unallocated memory. [1] Link: https://lore.kernel.org/all/ZkNcALr3W3KGYYJG@gmail.com/

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix array-index-out-of-bounds in dml2/FCLKChangeSupport [Why] Potential out of bounds access in dml2_calculate_rq_and_dlg_params() because the value of out_lowest_state_idx used as an index for FCLKChangeSupport array can be greater than 1. [How] Currently dml2 core specifies identical values for all FCLKChangeSupport elements. Always use index 0 in the condition to avoid out of bounds access.

In the Linux kernel, the following vulnerability has been resolved: nvme: avoid double free special payload If a discard request needs to be retried, and that retry may fail before a new special payload is added, a double free will result. Clear the RQF_SPECIAL_LOAD when the request is cleaned.

ImageMagick is a free and open-source software suite, used for editing and manipulating digital images. The `AppImage` version `ImageMagick` might use an empty path when setting `MAGICK_CONFIGURE_PATH` and `LD_LIBRARY_PATH` environment variables while executing, which might lead to arbitrary code execution by loading malicious configuration files or shared libraries in the current working directory while executing `ImageMagick`. The vulnerability is fixed in 7.11-36.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Disassociate vcpus from redistributor region on teardown When tearing down a redistributor region, make sure we don't have any dangling pointer to that region stored in a vcpu.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: wait for ondemand_object_worker to finish when dropping object When queuing ondemand_object_worker() to re-open the object, cachefiles_object is not pinned. The cachefiles_object may be freed when the pending read request is completed intentionally and the related erofs is umounted. If ondemand_object_worker() runs after the object is freed, it will incur use-after-free problem as shown below. process A processs B process C process D cachefiles_ondemand_send_req() // send a read req X // wait for its completion // close ondemand fd cachefiles_ondemand_fd_release() // set object as CLOSE cachefiles_ondemand_daemon_read() // set object as REOPENING queue_work(fscache_wq, &info->ondemand_work) // close /dev/cachefiles cachefiles_daemon_release cachefiles_flush_reqs complete(&req->done) // read req X is completed // umount the erofs fs cachefiles_put_object() // object will be freed cachefiles_ondemand_deinit_obj_info() kmem_cache_free(object) // both info and object are freed ondemand_object_worker() When dropping an object, it is no longer necessary to reopen the object, so use cancel_work_sync() to cancel or wait for ondemand_object_worker() to finish.

Buffer overflow in the CA-driver (dst_ca.c) for TwinHan DST Frontend/Card in Linux kernel 2.6.12 and other versions before 2.6.15 allows local users to cause a denial of service (crash) and possibly execute arbitrary code by "reading more than 8 bytes into an 8 byte long array".

In the Linux kernel, the following vulnerability has been resolved: xhci: Handle TD clearing for multiple streams case When multiple streams are in use, multiple TDs might be in flight when an endpoint is stopped. We need to issue a Set TR Dequeue Pointer for each, to ensure everything is reset properly and the caches cleared. Change the logic so that any N>1 TDs found active for different streams are deferred until after the first one is processed, calling xhci_invalidate_cancelled_tds() again from xhci_handle_cmd_set_deq() to queue another command until we are done with all of them. Also change the error/"should never happen" paths to ensure we at least clear any affected TDs, even if we can't issue a command to clear the hardware cache, and complain loudly with an xhci_warn() if this ever happens. This problem case dates back to commit e9df17eb1408 ("USB: xhci: Correct assumptions about number of rings per endpoint.") early on in the XHCI driver's life, when stream support was first added. It was then identified but not fixed nor made into a warning in commit 674f8438c121 ("xhci: split handling halted endpoints into two steps"), which added a FIXME comment for the problem case (without materially changing the behavior as far as I can tell, though the new logic made the problem more obvious). Then later, in commit 94f339147fc3 ("xhci: Fix failure to give back some cached cancelled URBs."), it was acknowledged again. [Mathias: commit 94f339147fc3 ("xhci: Fix failure to give back some cached cancelled URBs.") was a targeted regression fix to the previously mentioned patch. Users reported issues with usb stuck after unmounting/disconnecting UAS devices. This rolled back the TD clearing of multiple streams to its original state.] Apparently the commit author was aware of the problem (yet still chose to submit it): It was still mentioned as a FIXME, an xhci_dbg() was added to log the problem condition, and the remaining issue was mentioned in the commit description. The choice of making the log type xhci_dbg() for what is, at this point, a completely unhandled and known broken condition is puzzling and unfortunate, as it guarantees that no actual users would see the log in production, thereby making it nigh undebuggable (indeed, even if you turn on DEBUG, the message doesn't really hint at there being a problem at all). It took me *months* of random xHC crashes to finally find a reliable repro and be able to do a deep dive debug session, which could all have been avoided had this unhandled, broken condition been actually reported with a warning, as it should have been as a bug intentionally left in unfixed (never mind that it shouldn't have been left in at all). > Another fix to solve clearing the caches of all stream rings with > cancelled TDs is needed, but not as urgent. 3 years after that statement and 14 years after the original bug was introduced, I think it's finally time to fix it. And maybe next time let's not leave bugs unfixed (that are actually worse than the original bug), and let's actually get people to review kernel commits please. Fixes xHC crashes and IOMMU faults with UAS devices when handling errors/faults. Easiest repro is to use `hdparm` to mark an early sector (e.g. 1024) on a disk as bad, then `cat /dev/sdX > /dev/null` in a loop. At least in the case of JMicron controllers, the read errors end up having to cancel two TDs (for two queued requests to different streams) and the one that didn't get cleared properly ends up faulting the xHC entirely when it tries to access DMA pages that have since been unmapped, referred to by the stale TDs. This normally happens quickly (after two or three loops). After this fix, I left the `cat` in a loop running overnight and experienced no xHC failures, with all read errors recovered properly. Repro'd and tested on an Apple M1 Mac Mini (dwc3 host). On systems without an IOMMU, this bug would instead silently corrupt freed memory, making this a ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ASoC: topology: Fix references to freed memory Most users after parsing a topology file, release memory used by it, so having pointer references directly into topology file contents is wrong. Use devm_kmemdup(), to allocate memory as needed.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: mst: fix suspicious rcu usage in br_mst_set_state I converted br_mst_set_state to RCU to avoid a vlan use-after-free but forgot to change the vlan group dereference helper. Switch to vlan group RCU deref helper to fix the suspicious rcu usage warning.

In the Linux kernel, the following vulnerability has been resolved: block: avoid to reuse `hctx` not removed from cpuhp callback list If the 'hctx' isn't removed from cpuhp callback list, we can't reuse it, otherwise use-after-free may be triggered.

In the Linux kernel, the following vulnerability has been resolved: ptp: fix integer overflow in max_vclocks_store On 32bit systems, the "4 * max" multiply can overflow. Use kcalloc() to do the allocation to prevent this.

In the Linux kernel, the following vulnerability has been resolved: firmware: cs_dsp: Fix overflow checking of wmfw header Fix the checking that firmware file buffer is large enough for the wmfw header, to prevent overrunning the buffer. The original code tested that the firmware data buffer contained enough bytes for the sums of the size of the structs wmfw_header + wmfw_adsp1_sizes + wmfw_footer But wmfw_adsp1_sizes is only used on ADSP1 firmware. For ADSP2 and Halo Core the equivalent struct is wmfw_adsp2_sizes, which is 4 bytes longer. So the length check didn't guarantee that there are enough bytes in the firmware buffer for a header with wmfw_adsp2_sizes. This patch splits the length check into three separate parts. Each of the wmfw_header, wmfw_adsp?_sizes and wmfw_footer are checked separately before they are used.

In the Linux kernel, the following vulnerability has been resolved: block/ioctl: prefer different overflow check Running syzkaller with the newly reintroduced signed integer overflow sanitizer shows this report: [ 62.982337] ------------[ cut here ]------------ [ 62.985692] cgroup: Invalid name [ 62.986211] UBSAN: signed-integer-overflow in ../block/ioctl.c:36:46 [ 62.989370] 9pnet_fd: p9_fd_create_tcp (7343): problem connecting socket to 127.0.0.1 [ 62.992992] 9223372036854775807 + 4095 cannot be represented in type 'long long' [ 62.997827] 9pnet_fd: p9_fd_create_tcp (7345): problem connecting socket to 127.0.0.1 [ 62.999369] random: crng reseeded on system resumption [ 63.000634] GUP no longer grows the stack in syz-executor.2 (7353): 20002000-20003000 (20001000) [ 63.000668] CPU: 0 PID: 7353 Comm: syz-executor.2 Not tainted 6.8.0-rc2-00035-gb3ef86b5a957 #1 [ 63.000677] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 63.000682] Call Trace: [ 63.000686] <TASK> [ 63.000731] dump_stack_lvl+0x93/0xd0 [ 63.000919] __get_user_pages+0x903/0xd30 [ 63.001030] __gup_longterm_locked+0x153e/0x1ba0 [ 63.001041] ? _raw_read_unlock_irqrestore+0x17/0x50 [ 63.001072] ? try_get_folio+0x29c/0x2d0 [ 63.001083] internal_get_user_pages_fast+0x1119/0x1530 [ 63.001109] iov_iter_extract_pages+0x23b/0x580 [ 63.001206] bio_iov_iter_get_pages+0x4de/0x1220 [ 63.001235] iomap_dio_bio_iter+0x9b6/0x1410 [ 63.001297] __iomap_dio_rw+0xab4/0x1810 [ 63.001316] iomap_dio_rw+0x45/0xa0 [ 63.001328] ext4_file_write_iter+0xdde/0x1390 [ 63.001372] vfs_write+0x599/0xbd0 [ 63.001394] ksys_write+0xc8/0x190 [ 63.001403] do_syscall_64+0xd4/0x1b0 [ 63.001421] ? arch_exit_to_user_mode_prepare+0x3a/0x60 [ 63.001479] entry_SYSCALL_64_after_hwframe+0x6f/0x77 [ 63.001535] RIP: 0033:0x7f7fd3ebf539 [ 63.001551] Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 f1 14 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 [ 63.001562] RSP: 002b:00007f7fd32570c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 63.001584] RAX: ffffffffffffffda RBX: 00007f7fd3ff3f80 RCX: 00007f7fd3ebf539 [ 63.001590] RDX: 4db6d1e4f7e43360 RSI: 0000000020000000 RDI: 0000000000000004 [ 63.001595] RBP: 00007f7fd3f1e496 R08: 0000000000000000 R09: 0000000000000000 [ 63.001599] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 [ 63.001604] R13: 0000000000000006 R14: 00007f7fd3ff3f80 R15: 00007ffd415ad2b8 ... [ 63.018142] ---[ end trace ]--- Historically, the signed integer overflow sanitizer did not work in the kernel due to its interaction with `-fwrapv` but this has since been changed [1] in the newest version of Clang; It was re-enabled in the kernel with Commit 557f8c582a9ba8ab ("ubsan: Reintroduce signed overflow sanitizer"). Let's rework this overflow checking logic to not actually perform an overflow during the check itself, thus avoiding the UBSAN splat. [1]: https://github.com/llvm/llvm-project/pull/82432

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Fix potential UAF by revoke of fence registers CI has been sporadically reporting the following issue triggered by igt@i915_selftest@live@hangcheck on ADL-P and similar machines: <6> [414.049203] i915: Running intel_hangcheck_live_selftests/igt_reset_evict_fence ... <6> [414.068804] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled <6> [414.068812] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled <3> [414.070354] Unable to pin Y-tiled fence; err:-4 <3> [414.071282] i915_vma_revoke_fence:301 GEM_BUG_ON(!i915_active_is_idle(&fence->active)) ... <4>[ 609.603992] ------------[ cut here ]------------ <2>[ 609.603995] kernel BUG at drivers/gpu/drm/i915/gt/intel_ggtt_fencing.c:301! <4>[ 609.604003] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI <4>[ 609.604006] CPU: 0 PID: 268 Comm: kworker/u64:3 Tainted: G U W 6.9.0-CI_DRM_14785-g1ba62f8cea9c+ #1 <4>[ 609.604008] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR4 RVP, BIOS RPLPFWI1.R00.4035.A00.2301200723 01/20/2023 <4>[ 609.604010] Workqueue: i915 __i915_gem_free_work [i915] <4>[ 609.604149] RIP: 0010:i915_vma_revoke_fence+0x187/0x1f0 [i915] ... <4>[ 609.604271] Call Trace: <4>[ 609.604273] <TASK> ... <4>[ 609.604716] __i915_vma_evict+0x2e9/0x550 [i915] <4>[ 609.604852] __i915_vma_unbind+0x7c/0x160 [i915] <4>[ 609.604977] force_unbind+0x24/0xa0 [i915] <4>[ 609.605098] i915_vma_destroy+0x2f/0xa0 [i915] <4>[ 609.605210] __i915_gem_object_pages_fini+0x51/0x2f0 [i915] <4>[ 609.605330] __i915_gem_free_objects.isra.0+0x6a/0xc0 [i915] <4>[ 609.605440] process_scheduled_works+0x351/0x690 ... In the past, there were similar failures reported by CI from other IGT tests, observed on other platforms. Before commit 63baf4f3d587 ("drm/i915/gt: Only wait for GPU activity before unbinding a GGTT fence"), i915_vma_revoke_fence() was waiting for idleness of vma->active via fence_update(). That commit introduced vma->fence->active in order for the fence_update() to be able to wait selectively on that one instead of vma->active since only idleness of fence registers was needed. But then, another commit 0d86ee35097a ("drm/i915/gt: Make fence revocation unequivocal") replaced the call to fence_update() in i915_vma_revoke_fence() with only fence_write(), and also added that GEM_BUG_ON(!i915_active_is_idle(&fence->active)) in front. No justification was provided on why we might then expect idleness of vma->fence->active without first waiting on it. The issue can be potentially caused by a race among revocation of fence registers on one side and sequential execution of signal callbacks invoked on completion of a request that was using them on the other, still processed in parallel to revocation of those fence registers. Fix it by waiting for idleness of vma->fence->active in i915_vma_revoke_fence(). (cherry picked from commit 24bb052d3dd499c5956abad5f7d8e4fd07da7fb1)

In the Linux kernel, the following vulnerability has been resolved: ata: libata-core: Fix double free on error If e.g. the ata_port_alloc() call in ata_host_alloc() fails, we will jump to the err_out label, which will call devres_release_group(). devres_release_group() will trigger a call to ata_host_release(). ata_host_release() calls kfree(host), so executing the kfree(host) in ata_host_alloc() will lead to a double free: kernel BUG at mm/slub.c:553! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 11 PID: 599 Comm: (udev-worker) Not tainted 6.10.0-rc5 #47 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:kfree+0x2cf/0x2f0 Code: 5d 41 5e 41 5f 5d e9 80 d6 ff ff 4d 89 f1 41 b8 01 00 00 00 48 89 d9 48 89 da RSP: 0018:ffffc90000f377f0 EFLAGS: 00010246 RAX: ffff888112b1f2c0 RBX: ffff888112b1f2c0 RCX: ffff888112b1f320 RDX: 000000000000400b RSI: ffffffffc02c9de5 RDI: ffff888112b1f2c0 RBP: ffffc90000f37830 R08: 0000000000000000 R09: 0000000000000000 R10: ffffc90000f37610 R11: 617461203a736b6e R12: ffffea00044ac780 R13: ffff888100046400 R14: ffffffffc02c9de5 R15: 0000000000000006 FS: 00007f2f1cabe980(0000) GS:ffff88813b380000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2f1c3acf75 CR3: 0000000111724000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? die+0x2e/0x50 ? do_trap+0xca/0x110 ? do_error_trap+0x6a/0x90 ? kfree+0x2cf/0x2f0 ? exc_invalid_op+0x50/0x70 ? kfree+0x2cf/0x2f0 ? asm_exc_invalid_op+0x1a/0x20 ? ata_host_alloc+0xf5/0x120 [libata] ? ata_host_alloc+0xf5/0x120 [libata] ? kfree+0x2cf/0x2f0 ata_host_alloc+0xf5/0x120 [libata] ata_host_alloc_pinfo+0x14/0xa0 [libata] ahci_init_one+0x6c9/0xd20 [ahci] Ensure that we will not call kfree(host) twice, by performing the kfree() only if the devres_open_group() call failed.

In the Linux kernel, the following vulnerability has been resolved: jfs: xattr: fix buffer overflow for invalid xattr When an xattr size is not what is expected, it is printed out to the kernel log in hex format as a form of debugging. But when that xattr size is bigger than the expected size, printing it out can cause an access off the end of the buffer. Fix this all up by properly restricting the size of the debug hex dump in the kernel log.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: defer exposing anon_fd until after copy_to_user() succeeds After installing the anonymous fd, we can now see it in userland and close it. However, at this point we may not have gotten the reference count of the cache, but we will put it during colse fd, so this may cause a cache UAF. So grab the cache reference count before fd_install(). In addition, by kernel convention, fd is taken over by the user land after fd_install(), and the kernel should not call close_fd() after that, i.e., it should call fd_install() after everything is ready, thus fd_install() is called after copy_to_user() succeeds.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: remove requests from xarray during flushing requests Even with CACHEFILES_DEAD set, we can still read the requests, so in the following concurrency the request may be used after it has been freed: mount | daemon_thread1 | daemon_thread2 ------------------------------------------------------------ cachefiles_ondemand_init_object cachefiles_ondemand_send_req REQ_A = kzalloc(sizeof(*req) + data_len) wait_for_completion(&REQ_A->done) cachefiles_daemon_read cachefiles_ondemand_daemon_read // close dev fd cachefiles_flush_reqs complete(&REQ_A->done) kfree(REQ_A) xa_lock(&cache->reqs); cachefiles_ondemand_select_req req->msg.opcode != CACHEFILES_OP_READ // req use-after-free !!! xa_unlock(&cache->reqs); xa_destroy(&cache->reqs) Hence remove requests from cache->reqs when flushing them to avoid accessing freed requests.

In the Linux kernel, the following vulnerability has been resolved: PCI/MSI: Fix UAF in msi_capability_init KFENCE reports the following UAF: BUG: KFENCE: use-after-free read in __pci_enable_msi_range+0x2c0/0x488 Use-after-free read at 0x0000000024629571 (in kfence-#12): __pci_enable_msi_range+0x2c0/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 kfence-#12: 0x0000000008614900-0x00000000e06c228d, size=104, cache=kmalloc-128 allocated by task 81 on cpu 7 at 10.808142s: __kmem_cache_alloc_node+0x1f0/0x2bc kmalloc_trace+0x44/0x138 msi_alloc_desc+0x3c/0x9c msi_domain_insert_msi_desc+0x30/0x78 msi_setup_msi_desc+0x13c/0x184 __pci_enable_msi_range+0x258/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 freed by task 81 on cpu 7 at 10.811436s: msi_domain_free_descs+0xd4/0x10c msi_domain_free_locked.part.0+0xc0/0x1d8 msi_domain_alloc_irqs_all_locked+0xb4/0xbc pci_msi_setup_msi_irqs+0x30/0x4c __pci_enable_msi_range+0x2a8/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 Descriptor allocation done in: __pci_enable_msi_range msi_capability_init msi_setup_msi_desc msi_insert_msi_desc msi_domain_insert_msi_desc msi_alloc_desc ... Freed in case of failure in __msi_domain_alloc_locked() __pci_enable_msi_range msi_capability_init pci_msi_setup_msi_irqs msi_domain_alloc_irqs_all_locked msi_domain_alloc_locked __msi_domain_alloc_locked => fails msi_domain_free_locked ... That failure propagates back to pci_msi_setup_msi_irqs() in msi_capability_init() which accesses the descriptor for unmasking in the error exit path. Cure it by copying the descriptor and using the copy for the error exit path unmask operation. [ tglx: Massaged change log ]

In the Linux kernel, the following vulnerability has been resolved: cachefiles: fix slab-use-after-free in fscache_withdraw_volume() We got the following issue in our fault injection stress test: ================================================================== BUG: KASAN: slab-use-after-free in fscache_withdraw_volume+0x2e1/0x370 Read of size 4 at addr ffff88810680be08 by task ondemand-04-dae/5798 CPU: 0 PID: 5798 Comm: ondemand-04-dae Not tainted 6.8.0-dirty #565 Call Trace: kasan_check_range+0xf6/0x1b0 fscache_withdraw_volume+0x2e1/0x370 cachefiles_withdraw_volume+0x31/0x50 cachefiles_withdraw_cache+0x3ad/0x900 cachefiles_put_unbind_pincount+0x1f6/0x250 cachefiles_daemon_release+0x13b/0x290 __fput+0x204/0xa00 task_work_run+0x139/0x230 Allocated by task 5820: __kmalloc+0x1df/0x4b0 fscache_alloc_volume+0x70/0x600 __fscache_acquire_volume+0x1c/0x610 erofs_fscache_register_volume+0x96/0x1a0 erofs_fscache_register_fs+0x49a/0x690 erofs_fc_fill_super+0x6c0/0xcc0 vfs_get_super+0xa9/0x140 vfs_get_tree+0x8e/0x300 do_new_mount+0x28c/0x580 [...] Freed by task 5820: kfree+0xf1/0x2c0 fscache_put_volume.part.0+0x5cb/0x9e0 erofs_fscache_unregister_fs+0x157/0x1b0 erofs_kill_sb+0xd9/0x1c0 deactivate_locked_super+0xa3/0x100 vfs_get_super+0x105/0x140 vfs_get_tree+0x8e/0x300 do_new_mount+0x28c/0x580 [...] ================================================================== Following is the process that triggers the issue: mount failed | daemon exit ------------------------------------------------------------ deactivate_locked_super cachefiles_daemon_release erofs_kill_sb erofs_fscache_unregister_fs fscache_relinquish_volume __fscache_relinquish_volume fscache_put_volume(fscache_volume, fscache_volume_put_relinquish) zero = __refcount_dec_and_test(&fscache_volume->ref, &ref); cachefiles_put_unbind_pincount cachefiles_daemon_unbind cachefiles_withdraw_cache cachefiles_withdraw_volumes list_del_init(&volume->cache_link) fscache_free_volume(fscache_volume) cache->ops->free_volume cachefiles_free_volume list_del_init(&cachefiles_volume->cache_link); kfree(fscache_volume) cachefiles_withdraw_volume fscache_withdraw_volume fscache_volume->n_accesses // fscache_volume UAF !!! The fscache_volume in cache->volumes must not have been freed yet, but its reference count may be 0. So use the new fscache_try_get_volume() helper function try to get its reference count. If the reference count of fscache_volume is 0, fscache_put_volume() is freeing it, so wait for it to be removed from cache->volumes. If its reference count is not 0, call cachefiles_withdraw_volume() with reference count protection to avoid the above issue.

The dvd_read_bca function in the DVD handling code in drivers/cdrom/cdrom.c in Linux kernel 2.2.16, and later versions, assigns the wrong value to a length variable, which allows local users to execute arbitrary code via a crafted USB Storage device that triggers a buffer overflow.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: flush all requests after setting CACHEFILES_DEAD In ondemand mode, when the daemon is processing an open request, if the kernel flags the cache as CACHEFILES_DEAD, the cachefiles_daemon_write() will always return -EIO, so the daemon can't pass the copen to the kernel. Then the kernel process that is waiting for the copen triggers a hung_task. Since the DEAD state is irreversible, it can only be exited by closing /dev/cachefiles. Therefore, after calling cachefiles_io_error() to mark the cache as CACHEFILES_DEAD, if in ondemand mode, flush all requests to avoid the above hungtask. We may still be able to read some of the cached data before closing the fd of /dev/cachefiles. Note that this relies on the patch that adds reference counting to the req, otherwise it may UAF.

In the Linux kernel, the following vulnerability has been resolved: ionic: fix use after netif_napi_del() When queues are started, netif_napi_add() and napi_enable() are called. If there are 4 queues and only 3 queues are used for the current configuration, only 3 queues' napi should be registered and enabled. The ionic_qcq_enable() checks whether the .poll pointer is not NULL for enabling only the using queue' napi. Unused queues' napi will not be registered by netif_napi_add(), so the .poll pointer indicates NULL. But it couldn't distinguish whether the napi was unregistered or not because netif_napi_del() doesn't reset the .poll pointer to NULL. So, ionic_qcq_enable() calls napi_enable() for the queue, which was unregistered by netif_napi_del(). Reproducer: ethtool -L <interface name> rx 1 tx 1 combined 0 ethtool -L <interface name> rx 0 tx 0 combined 1 ethtool -L <interface name> rx 0 tx 0 combined 4 Splat looks like: kernel BUG at net/core/dev.c:6666! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 PID: 1057 Comm: kworker/3:3 Not tainted 6.10.0-rc2+ #16 Workqueue: events ionic_lif_deferred_work [ionic] RIP: 0010:napi_enable+0x3b/0x40 Code: 48 89 c2 48 83 e2 f6 80 b9 61 09 00 00 00 74 0d 48 83 bf 60 01 00 00 00 74 03 80 ce 01 f0 4f RSP: 0018:ffffb6ed83227d48 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff97560cda0828 RCX: 0000000000000029 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff97560cda0a28 RBP: ffffb6ed83227d50 R08: 0000000000000400 R09: 0000000000000001 R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000 R13: ffff97560ce3c1a0 R14: 0000000000000000 R15: ffff975613ba0a20 FS: 0000000000000000(0000) GS:ffff975d5f780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8f734ee200 CR3: 0000000103e50000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? die+0x33/0x90 ? do_trap+0xd9/0x100 ? napi_enable+0x3b/0x40 ? do_error_trap+0x83/0xb0 ? napi_enable+0x3b/0x40 ? napi_enable+0x3b/0x40 ? exc_invalid_op+0x4e/0x70 ? napi_enable+0x3b/0x40 ? asm_exc_invalid_op+0x16/0x20 ? napi_enable+0x3b/0x40 ionic_qcq_enable+0xb7/0x180 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_start_queues+0xc4/0x290 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_link_status_check+0x11c/0x170 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_lif_deferred_work+0x129/0x280 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] process_one_work+0x145/0x360 worker_thread+0x2bb/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0xcc/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: cachefiles: fix slab-use-after-free in cachefiles_ondemand_daemon_read() We got the following issue in a fuzz test of randomly issuing the restore command: ================================================================== BUG: KASAN: slab-use-after-free in cachefiles_ondemand_daemon_read+0xb41/0xb60 Read of size 8 at addr ffff888122e84088 by task ondemand-04-dae/963 CPU: 13 PID: 963 Comm: ondemand-04-dae Not tainted 6.8.0-dirty #564 Call Trace: kasan_report+0x93/0xc0 cachefiles_ondemand_daemon_read+0xb41/0xb60 vfs_read+0x169/0xb50 ksys_read+0xf5/0x1e0 Allocated by task 116: kmem_cache_alloc+0x140/0x3a0 cachefiles_lookup_cookie+0x140/0xcd0 fscache_cookie_state_machine+0x43c/0x1230 [...] Freed by task 792: kmem_cache_free+0xfe/0x390 cachefiles_put_object+0x241/0x480 fscache_cookie_state_machine+0x5c8/0x1230 [...] ================================================================== Following is the process that triggers the issue: mount | daemon_thread1 | daemon_thread2 ------------------------------------------------------------ cachefiles_withdraw_cookie cachefiles_ondemand_clean_object(object) cachefiles_ondemand_send_req REQ_A = kzalloc(sizeof(*req) + data_len) wait_for_completion(&REQ_A->done) cachefiles_daemon_read cachefiles_ondemand_daemon_read REQ_A = cachefiles_ondemand_select_req msg->object_id = req->object->ondemand->ondemand_id ------ restore ------ cachefiles_ondemand_restore xas_for_each(&xas, req, ULONG_MAX) xas_set_mark(&xas, CACHEFILES_REQ_NEW) cachefiles_daemon_read cachefiles_ondemand_daemon_read REQ_A = cachefiles_ondemand_select_req copy_to_user(_buffer, msg, n) xa_erase(&cache->reqs, id) complete(&REQ_A->done) ------ close(fd) ------ cachefiles_ondemand_fd_release cachefiles_put_object cachefiles_put_object kmem_cache_free(cachefiles_object_jar, object) REQ_A->object->ondemand->ondemand_id // object UAF !!! When we see the request within xa_lock, req->object must not have been freed yet, so grab the reference count of object before xa_unlock to avoid the above issue.