On Juniper Networks EX2300 Series, receipt of a stream of specific multicast packets by the layer2 interface can cause high CPU load, which could lead to traffic interruption. This issue occurs when multicast packets are received by the layer 2 interface. To check if the device has high CPU load due to this issue, the administrator can issue the following command: user@host> show chassis routing-engine Routing Engine status: ... Idle 2 percent the "Idle" value shows as low (2 % in the example above), and also the following command: user@host> show system processes summary ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 11639 root 52 0 283M 11296K select 12:15 44.97% eventd 11803 root 81 0 719M 239M RUN 251:12 31.98% fxpc{fxpc} the eventd and the fxpc processes might use higher WCPU percentage (respectively 44.97% and 31.98% in the above example). This issue affects Juniper Networks Junos OS on EX2300 Series: 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2.

An Uncontrolled Resource Consumption vulnerability in Juniper Networks Junos OS on EX2300, EX3400 and EX4300 Series platforms allows an adjacent attacker sending a stream of layer 2 frames will trigger an Aggregated Ethernet (AE) interface to go down and thereby causing a Denial of Service (DoS). By continuously sending a stream of specific layer 2 frames an attacker will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS EX4300 Series All versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS EX3400 and EX4300-MP Series All versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S9, 18.4R3-S7; 19.1 versions prior to 19.1R2-S3, 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. Juniper Networks Junos OS EX2300 Series All versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R2.

On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPCs (Modular Port Concentrators) where Integrated Routing and Bridging (IRB) interfaces are configured and mapped to a VPLS instance or a Bridge-Domain, certain Layer 2 network events at Customer Edge (CE) devices may cause memory leaks in the MPC of Provider Edge (PE) devices which can cause an out of memory condition and MPC restart. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines), including MX-MPC1-3D, MX-MPC1E-3D, MX-MPC2-3D, MX-MPC2E-3D, MPC-3D-16XGE, and CHAS-MXxx Series MPCs. No other products or platforms are affected by this issue. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S3; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.2 versions prior to 20.2R1-S3, 20.2R2; 20.3 versions prior to 20.3R1-S1,, 20.3R2. This issue does not affect Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R3-S2; 18.1; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R3-S1; 19.1; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2.

On Juniper Networks Junos EX series, QFX Series, MX Series and SRX branch series devices, a memory leak occurs every time the 802.1X authenticator port interface flaps which can lead to other processes, such as the pfex process, responsible for packet forwarding, to crash and restart. An administrator can use the following CLI command to monitor the status of memory consumption: user@device> show task memory detail Please refer to https://kb.juniper.net/KB31522 for details. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D54; 15.1X49 versions prior to 15.1X49-D240 ; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10 ; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. This issue does not affect Juniper Networks Junos OS 12.3, 15.1.

An Uncontrolled Resource Consumption vulnerability in the ARP daemon (arpd) and Network Discovery Protocol (ndp) process of Juniper Networks Junos OS Evolved allows a malicious attacker on the local network to consume memory resources, ultimately resulting in a Denial of Service (DoS) condition. Link-layer functions such as IPv4 and/or IPv6 address resolution may be impacted, leading to traffic loss. The processes do not recover on their own and must be manually restarted. Changes in memory usage can be monitored using the following shell commands (header shown for clarity): user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 59.0 0.7 *5702564* 247952 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 49.1 1.0 *5813156* 351184 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 Memory usage can be monitored for the ndp process in a similar fashion: user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5614052* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5725164* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje This issue affects Juniper Networks Junos OS Evolved: 19.4 versions prior to 19.4R2-S3-EVO; 20.1 versions prior to 20.1R2-S4-EVO; all versions of 20.2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 19.4R2-EVO.

The kernel memory usage represented as "temp" via 'show system virtual-memory' may constantly increase when Integrated Routing and Bridging (IRB) is configured with multiple underlay physical interfaces, and one interface flaps. This memory leak can affect running daemons (processes), leading to an extended Denial of Service (DoS) condition. Usage of "temp" virtual memory, shown here by a constantly increasing value of outstanding Requests, can be monitored by executing the 'show system virtual-memory' command as shown below: user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 10551 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6460 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 16101 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6665 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 21867 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6858 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2. This issue does not affect Juniper Networks Junos OS 12.3 and 15.1.

An Uncontrolled Resource Consumption vulnerability in the Connectivity Fault Management (CFM) daemon and the Connectivity Fault Management Manager (cfmman) of Juniper Networks Junos OS Evolved on PTX10001-36MR, PTX10002-36QDD, PTX10004, PTX10008, PTX10016 allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). An attacker on an adjacent device sending specific valid traffic can cause cfmd to spike the CPU to 100% and cfmman's memory to leak, eventually to cause the FPC crash and restart. Continued receipt and processes of these specific valid packets will sustain the Denial of Service (DoS) condition. An indicator of compromise is to watch for an increase in cfmman memory rising over time by issuing the following command and evaluating the RSS number. If the RSS is growing into GBs then consider restarting the device to temporarily clear memory.   user@device> show system processes node fpc<num> detail | match cfmman Example:    show system processes node fpc0 detail | match cfmman    F S UID       PID       PPID PGID   SID   C PRI NI  ADDR SZ    WCHAN   RSS     PSR STIME TTY         TIME     CMD   4 S root      15204     1    15204  15204 0 80  0   - 90802     -      113652   4  Sep25 ?           00:15:28 /usr/bin/cfmman -p /var/pfe -o -c /usr/conf/cfmman-cfg-active.xml This issue affects Junos OS Evolved on PTX10001-36MR, PTX10002-36QDD, PTX10004, PTX10008, PTX10016: * from 23.2R1-EVO before 23.2R2-S4-EVO, * from 23.4 before 23.4R2-S4-EVO, * from 24.2 before 24.2R2-EVO, * from 24.4 before 24.4R1-S2-EVO, 24.4R2-EVO. This issue does not affect Junos OS Evolved on PTX10001-36MR, PTX10002-36QDD, PTX10004, PTX10008, PTX10016 before 23.2R1-EVO.

On Juniper Networks EX4300-MP Series, EX4600 Series and QFX5K Series deployed in a Virtual Chassis configuration, receipt of a stream of specific layer 2 frames can cause high CPU load, which could lead to traffic interruption. This issue does not occur when the device is deployed in Stand Alone configuration. The offending layer 2 frame packets can originate only from within the broadcast domain where the device is connected. This issue affects Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series and QFX5K Series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2.

On Juniper Networks EX4300-MP Series, EX4600 Series and QFX5K Series deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, receipt of a stream of specific VXLAN encapsulated layer 2 frames can cause high CPU load, which could lead to network protocol operation issue and traffic interruption. This issue affects devices that are configured as a Layer 2 or Layer 3 gateway of an EVPN-VXLAN deployment. The offending layer 2 frames that cause the issue originate from a different access switch that get encapsulated within the same EVPN-VXLAN domain. This issue affects Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series and QFX5K Series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2.

On Juniper Networks Junos OS and Junos OS Evolved platforms with EVPN configured, receipt of specific BGP packets causes a slow memory leak. If the memory is exhausted the rpd process might crash. If the issue occurs, the memory leak could be seen by executing the "show task memory detail | match policy | match evpn" command multiple times to check if memory (Alloc Blocks value) is increasing. root@device> show task memory detail | match policy | match evpn ------------------------ Allocator Memory Report ------------------------ Name | Size | Alloc DTXP Size | Alloc Blocks | Alloc Bytes | MaxAlloc Blocks | MaxAlloc Bytes Policy EVPN Params 20 24 3330678 79936272 3330678 79936272 root@device> show task memory detail | match policy | match evpn ------------------------ Allocator Memory Report ------------------------ Name | Size | Alloc DTXP Size | Alloc Blocks | Alloc Bytes | MaxAlloc Blocks | MaxAlloc Bytes Policy EVPN Params 20 24 36620255 878886120 36620255 878886120 This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R2; 20.1 versions prior to 20.1R1-S4, 20.1R2; Juniper Networks Junos OS Evolved: 19.4 versions; 20.1 versions prior to 20.1R1-S4-EVO, 20.1R2-EVO; 20.2 versions prior to 20.2R1-EVO; This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

A vulnerability in the pfe-chassisd Chassis Manager (CMLC) daemon of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the EX4300 when specific valid broadcast packets create a broadcast storm condition when received on the me0 interface of the EX4300 Series device. A reboot of the device is required to restore service. Continued receipt of these valid broadcast packets will create a sustained Denial of Service (DoS) against the device. Affected releases are Juniper Networks Junos OS: 16.1 versions above and including 16.1R1 prior to 16.1R7-S5; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.

Crafted packets destined to the management interface (fxp0) of an SRX340 or SRX345 services gateway may create a denial of service (DoS) condition due to buffer space exhaustion. This issue only affects the SRX340 and SRX345 services gateways. No other products or platforms are affected by this vulnerability. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D160 on SRX340/SRX345; 17.3 on SRX340/SRX345; 17.4 versions prior to 17.4R2-S3, 17.4R3 on SRX340/SRX345; 18.1 versions prior to 18.1R3-S1 on SRX340/SRX345; 18.2 versions prior to 18.2R2 on SRX340/SRX345; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX340/SRX345. This issue does not affect Junos OS releases prior to 15.1X49 on any platform.

A vulnerability in the IP next-hop index database in Junos OS 17.3R3 may allow a flood of ARP requests, sent to the management interface, to exhaust the private Internal routing interfaces (IRIs) next-hop limit. Once the IRI next-hop database is full, no further next hops can be learned and existing entries cannot be cleared, leading to a sustained denial of service (DoS) condition. An indicator of compromise for this issue is the report of the following error message: %KERN-4: Nexthop index allocation failed: private index space exhausted This issue only affects the management interface, and does not impact regular transit traffic through the FPCs. This issue also only affects Junos OS 17.3R3. No prior versions of Junos OS are affected by this issue. Affected releases are Juniper Networks Junos OS: 17.3R3.

On QFX5000 Series and EX4600 switches, a high rate of Ethernet pause frames or an ARP packet storm received on the management interface (fxp0) can cause egress interface congestion, resulting in routing protocol packet drops, such as BGP, leading to peering flaps. The following log message may also be displayed: fpc0 dcbcm_check_stuck_buffers: Buffers are stuck on queue 7 of port 45 This issue only affects the QFX5000 Series products (QFX5100, QFX5110, QFX5200, QFX5210) and the EX4600 switch. No other platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D47 on QFX5000 Series and EX4600; 15.1 versions prior to 15.1R7, 15.1R8 on QFX5000 Series and EX4600; 15.1X53 versions prior to 15.1X53-D233 on QFX5000 Series and EX4600; 16.1 versions prior to 16.1R7 on QFX5000 Series and EX4600; 16.2 versions prior to 16.2R3 on QFX5000 Series and EX4600; 17.1 versions prior to 17.1R2-S9, 17.1R3 on QFX5000 Series and EX4600; 17.2 versions prior to 17.2R2-S6, 17.2R3 on QFX5000 Series and EX4600; 17.2X75 versions prior to 17.2X75-D42 on QFX5000 Series and EX4600; 17.3 versions prior to 17.3R3 on QFX5000 Series and EX4600; 17.4 versions prior to 17.4R2 on QFX5000 Series and EX4600; 18.1 versions prior to 18.1R2 on QFX5000 Series and EX4600.

An Uncontrolled Resource Consumption vulnerability in the handling of IPv6 neighbor state change events in Juniper Networks Junos OS allows an adjacent attacker to cause a memory leak in the Flexible PIC Concentrator (FPC) of an ACX5448 router. The continuous flapping of an IPv6 neighbor with specific timing will cause the FPC to run out of resources, leading to a Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition, requiring a manual PFE restart to restore service. The following error messages will be seen after the FPC resources have been exhausted: fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 fpc0 DNX_NH::dnx_nh_tag_ipv4_hw_install(),3135: dnx_nh_tag_ipv4_hw_install: BCM L3 Egress create object failed for NH 602 (-14:No resources for operation), BCM NH Params: unit:0 Port:41, L3_INTF:0 Flags: 0x40 This issue only affects the ACX5448 router. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS on ACX5448: 18.4 versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S8, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S1, 20.2R2.

A Denial of Service (DoS) vulnerability in the processing of a flood of specific ARP traffic in Juniper Networks Junos OS on the EX4300 switch, sent from the local broadcast domain, may allow an unauthenticated network-adjacent attacker to trigger a PFEMAN watchdog timeout, causing the Packet Forwarding Engine (PFE) to crash and restart. After the restart, transit traffic will be temporarily interrupted until the PFE is reprogrammed. In a virtual chassis (VC), the impacted Flexible PIC Concentrator (FPC) may split from the VC temporarily, and join back into the VC once the PFE restarts. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on the EX4300: All versions prior to 15.1R7-S12; 18.4 versions prior to 18.4R2-S10, 18.4R3-S11; 19.1 versions prior to 19.1R3-S8; 19.2 versions prior to 19.2R1-S9, 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2-S1, 21.2R3; 21.3 versions prior to 21.3R1-S2, 21.3R2.

An Uncontrolled Resource Consumption vulnerability in the Layer 2 Address Learning Daemon (l2ald) of Juniper Networks Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a memory leak, eventually exhausting all system memory, leading to a system crash and Denial of Service (DoS). Certain MAC table updates cause a small amount of memory to leak.  Once memory utilization reaches its limit, the issue will result in a system crash and restart. To identify the issue, execute the CLI command: user@device> show platform application-info allocations app l2ald-agent EVL Object Allocation Statistics: Node   Application     Context Name                               Live   Allocs   Fails     Guids re0   l2ald-agent               net::juniper::rtnh::L2Rtinfo       1069096 1069302   0         1069302 re0   l2ald-agent               net::juniper::rtnh::NHOpaqueTlv     114     195       0         195 This issue affects Junos OS Evolved: * All versions before 21.4R3-S8-EVO, * from 22.2-EVO before 22.2R3-S4-EVO, * from 22.3-EVO before 22.3R3-S3-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.

An Improper Check or Handling of Exceptional Conditions vulnerability in packet processing of Juniper Networks Junos OS on QFX10002 allows an unauthenticated, adjacent attacker on the local broadcast domain sending a malformed packet to the device, causing all PFEs other than the inbound PFE to wedge and to eventually restart, resulting in a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue can only be triggered by sending a specific malformed packet to the device. Transit traffic does not trigger this issue. An indication of this issue occurring can be seen through the following log messages: fpc0 expr_hostbound_packet_handler: Receive pe 73? fpc0 Cmerror Op Set: PE Chip: PE0[0]: PGQ:misc_intr: 0x00000020: Enqueue of a packet with out-of-range VOQ in 192K-VOQ mode (URI: /fpc/0/pfe/0/cm/0/PE_Chip/0/PECHIP_CMERROR_PGQ_MISC_INT_EVENTS_ENQ_192K_VIOL) The logs list below can also be observed when this issue occurs fpc0 Error: /fpc/0/pfe/0/cm/0/PE_Chip/0/PECHIP_CMERROR_PGQ_MISC_INT_EVENTS_ENQ_192K_VIOL (0x210107), scope: pfe, category: functional, severity: major, module: PE Chip, type: Description for PECHIP_CMERROR_PGQ_MISC_INT_EVENTS_ENQ_192K_VIOL fpc0 Performing action cmalarm for error /fpc/0/pfe/0/cm/0/PE_Chip/0/PECHIP_CMERROR_PGQ_MISC_INT_EVENTS_ENQ_192K_VIOL (0x210107) in module: PE Chip with scope: pfe category: functional level: major fpc0 Error: /fpc/0/pfe/0/cm/0/PE_Chip/0/PECHIP_CMERROR_CM_INT_REG_DCHK_PIPE (0x21011a), scope: pfe, category: functional, severity: fatal, module: PE Chip, type: Description for PECHIP_CMERROR_CM_INT_REG_DCHK_PIPE fpc0 Performing action cmalarm for error /fpc/0/pfe/0/cm/0/PE_Chip/0/PECHIP_CMERROR_CM_INT_REG_DCHK_PIPE (0x21011a) in module: PE Chip with scope: pfe category: functional level: fatal fpc0 Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/PE_Chip/0/PECHIP_CMERROR_CM_INT_REG_DCHK_PIPE (0x21011a) in module: PE Chip with scope: pfe category: functional level: fatal This issue affects Juniper Networks Junos OS on QFX10002: All versions prior to 19.1R3-S10; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S7; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S1, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2.

An Improper Check or Handling of Exceptional Conditions vulnerability in packet processing on the network interfaces of Juniper Networks Junos OS on JRR200 route reflector appliances allows an adjacent, network-based attacker sending a specific packet to the device to cause a kernel crash, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue can only be triggered by an attacker on the local broadcast domain. Packets routed to the device are unable to trigger this crash. This issue affects Juniper Networks Junos OS on JRR200: All versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S2, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2; 22.4 versions prior to 22.4R1-S1, 22.4R2.

A Missing Release of Memory after Effective Lifetime vulnerability in Flexible PIC Concentrator (FPC) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker from the same shared physical or logical network, to cause a heap memory leak and leading to FPC crash. On all Junos PTX Series and QFX10000 Series, when specific EVPN VXLAN Multicast packets are processed, an FPC heap memory leak is observed. The FPC memory usage can be monitored using the CLI command "show heap extensive". Following is an example output. ID Base Total(b) Free(b) Used(b) % Name Peak used % -- -------- --------- --------- --------- --- ----------- ----------- 0 37dcf000 3221225472 1694526368 1526699104 47 Kernel 47 1 17dcf000 1048576 1048576 0 0 TOE DMA 0 2 17ecf000 1048576 1048576 0 0 DMA 0 3 17fcf000 534773760 280968336 253805424 47 Packet DMA 47 This issue affects: Juniper Networks Junos OS PTX Series and QFX10000 Series 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.1R1 on PTX Series and QFX10000 Series.

A Protection Mechanism Failure vulnerability in RPD (routing protocol daemon) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent unauthenticated attacker to cause established IS-IS adjacencies to go down by sending a spoofed hello PDU leading to a Denial of Service (DoS) condition. Continued receipted of these spoofed PDUs will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS All versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R2-EVO; 21.1 versions prior to 21.1R2-EVO.

An Incomplete List of Disallowed Inputs vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and EX4600 Series allows an adjacent unauthenticated attacker which sends a high rate of specific multicast traffic to cause control traffic received from the network to be dropped. This will impact control protocols (including but not limited to routing-protocols) and lead to a Denial of Service (DoS). Continued receipt of this specific multicast traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX5000 and EX4600 Series: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.

In an MPLS P2MP environment a Loop with Unreachable Exit Condition vulnerability in the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker to cause high load on RPD which in turn may lead to routing protocol flaps. If a system with sensor-based-stats enabled receives a specific LDP FEC this can lead to the above condition. Continued receipted of such an LDP FEC will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 19.2 version 19.2R2 and later versions prior to 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.2R2. Juniper Networks Junos OS Evolved All versions prior to 20.1R2-S3-EVO; 20.3 versions prior to 20.3R1-S2-EVO.

A Buffer Copy without Checking Size of Input ('Classic Buffer Overflow') vulnerability in the advanced forwarding toolkit (evo-aftmand/evo-pfemand) of Juniper Networks Junos OS Evolved on PTX Series or QFX5000 Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS).An attacker sending crafted multicast packets will cause line cards running evo-aftmand/evo-pfemand to crash and restart or non-line card devices to crash and restart. Continued receipt and processing of these packets will sustain the Denial of Service (DoS) condition. This issue affects Junos OS Evolved PTX Series: * All versions before 22.4R3-S8-EVO, * from 23.2 before 23.2R2-S5-EVO, * from 23.4 before 23.4R2-EVO, * from 24.2 before 24.2R2-EVO, * from 24.4 before 24.4R2-EVO. This issue affects Junos OS Evolved on QFX5000 Series: * 22.2-EVO version before 22.2R3-S7-EVO, * 22.4-EVO version before 22.4R3-S7-EVO, * 23.2-EVO versions before 23.2R2-S4-EVO, * 23.4-EVO versions before 23.4R2-S5-EVO, * 24.2-EVO versions before 24.2R2-S1-EVO, * 24.4-EVO versions before 24.4R1-S3-EVO, 24.4R2-EVO. This issue does not affect Junos OS Evolved on QFX5000 Series versions before: 21.2R2-S1-EVO, 21.2R3-EVO, 21.3R2-EVO, 21.4R1-EVO, and 22.1R1-EVO.

A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows an adjacent attacker to cause a Denial of Service (DoS) by sending genuine BGP flowspec packets which cause an FPC heap memory leak. Once having run out of memory the FPC will crash and restart along with a core dump. Continued receipted of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S6; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos Evolved is not affected.

In an EVPN/VXLAN scenario, if an IRB interface with a virtual gateway address (VGA) is configured on a PE, a traffic loop may occur upon receipt of specific IP multicast traffic. The traffic loop will cause interface traffic to increase abnormally, ultimately leading to a Denial of Service (DoS) in packet processing. The following command could be used to monitor the interface traffic: user@junos> monitor interface traffic Interface Link Input packets (pps) Output packets (pps) et-0/0/1 Up 6492089274364 (70994959) 6492089235319 (70994956) et-0/0/25 Up 343458103 (1) 156844 (0) ae0 Up 9132519197257 (70994959) 9132519139454 (70994956) This issue affects Juniper Networks Junos OS on QFX Series: all versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S5, 18.4R3-S5; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S3; 19.2 versions prior to 19.2R1-S5, 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2.

A vulnerability in the processing of specific MPLS packets in Juniper Networks Junos OS on MX Series and EX9200 Series devices with Trio-based MPCs (Modular Port Concentrators) may cause FPC to crash and lead to a Denial of Service (DoS) condition. Continued receipt of this packet will sustain the Denial of Service (DoS) condition. This issue only affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines). This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2;

An Improper Input Validation vulnerability in the active-lease query portion in JDHCPD's DHCP Relay Agent of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) by sending a crafted DHCP packet to the device thereby crashing the jdhcpd DHCP service. This is typically configured for Broadband Subscriber Sessions. Continued receipt and processing of this crafted packet will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS Evolved.

A vulnerability due to the improper handling of direct memory access (DMA) buffers on EX4300 switches on Juniper Networks Junos OS allows an attacker sending specific unicast frames to trigger a Denial of Service (DoS) condition by exhausting DMA buffers, causing the FPC to crash and the device to restart. The DMA buffer leak is seen when receiving these specific, valid unicast frames on an interface without Layer 2 Protocol Tunneling (L2PT) or dot1x configured. Interfaces with either L2PT or dot1x configured are not vulnerable to this issue. When this issue occurs, DMA buffer usage keeps increasing and the following error log messages may be observed: Apr 14 14:29:34.360 /kernel: pid 64476 (pfex_junos), uid 0: exited on signal 11 (core dumped) Apr 14 14:29:33.790 init: pfe-manager (PID 64476) terminated by signal number 11. Core dumped! The DMA buffers on the FPC can be monitored by the executing vty command 'show heap': ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 4a46000 268435456 238230496 30204960 11 Kernel 1 18a46000 67108864 17618536 49490328 73 Bcm_sdk 2 23737000 117440512 18414552 99025960 84 DMA buf <<<<< keeps increasing 3 2a737000 16777216 16777216 0 0 DMA desc This issue affects Juniper Networks Junos OS on the EX4300: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2.

On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a specific DHCPv6 packet is received, resulting in a restart of the daemon. The daemon automatically restarts without intervention, but continued receipt and processing of these specific packets will repeatedly crash the JDHCPD process and sustain the Denial of Service (DoS) condition. This issue only affects DHCPv6. DHCPv4 is not affected by this issue. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1, 19.3R3-S2; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2.

Improper Handling of Exceptional Conditions in Ethernet interface frame processing of Juniper Networks Junos OS allows an attacker to send specially crafted frames over the local Ethernet segment, causing the interface to go into a down state, resulting in a Denial of Service (DoS) condition. The interface does not recover on its own and the FPC must be reset manually. Continued receipt and processing of these frames will create a sustained Denial of Service (DoS) condition. This issue is platform-specific and affects the following platforms and line cards: * MPC7E/8E/9E and MPC10E on MX240, MX480, MX960, MX2008, MX2010, and MX2020 * MX204, MX10003, MX10008, MX10016 * EX9200, EX9251 * SRX4600 No other products or platforms are affected by this vulnerability. An indication of this issue occurring can be seen in the system log messages, as shown below: user@host> show log messages | match "Failed to complete DFE tuning" fpc4 smic_phy_dfe_tuning_state: et-4/1/6 - Failed to complete DFE tuning (count 3) and interface will be in a permanently down state: user@host> show interfaces et-4/1/6 terse Interface Admin Link Proto Local Remote et-4/1/6 up down et-4/1/6.0 up down aenet --> ae101.0 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S7 on MX Series; 17.1R1 and later versions prior to 17.2R3-S3 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S11, 17.4R3-S1 on MX Series, SRX4600; 18.1 versions prior to 18.1R3-S10 on MX Series, EX9200 Series, SRX4600; 18.2 versions prior to 18.2R3-S3 on MX Series, EX9200 Series, SRX4600; 18.3 versions prior to 18.3R3-S1 on MX Series, EX9200 Series, SRX4600; 18.4 versions prior to 18.4R2-S3, 18.4R3 on MX Series, EX9200 Series, SRX4600; 19.1 versions prior to 19.1R2-S1, 19.1R3 on MX Series, EX9200 Series, SRX4600; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series, EX9200 Series, SRX4600; 19.3 versions prior to 19.3R2 on MX Series, EX9200 Series, SRX4600. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.

An improper input validation vulnerability in the Routing Protocol Daemon (RPD) service of Juniper Networks Junos OS allows an attacker to send a malformed RSVP packet when bidirectional LSPs are in use, which when received by an egress router crashes the RPD causing a Denial of Service (DoS) condition. Continued receipt of the packet will sustain the Denial of Service. This issue affects: Juniper Networks Junos OS: All versions prior to 17.3R3-S10 except 15.1X49-D240 for SRX series; 17.4 versions prior to 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S4; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R3-S3; 19.2 versions prior to 19.2R3; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R2-S2, 19.4R3-S1; 20.1 versions prior to 20.1R1-S4, 20.1R2; 15.1X49 versions prior to 15.1X49-D240 on SRX Series. Juniper Networks Junos OS Evolved: 19.3 versions prior to 19.3R2-S5-EVO; 19.4 versions prior to 19.4R2-S2-EVO; 20.1 versions prior to 20.1R1-S4-EVO.

When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: __default_arp_policer__ <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved.

On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, the Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash if a malformed DHCPv6 packet is received, resulting in a restart of the daemon. The daemon automatically restarts without intervention, but continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects DHCPv6. DHCPv4 is not affected by this issue. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2.

A vulnerability in the distributed or centralized periodic packet management daemon (PPMD) of Juniper Networks Junos OS may cause receipt of a malformed packet to crash and restart the PPMD process, leading to network destabilization, service interruption, and a Denial of Service (DoS) condition. Continued receipt and processing of these malformed packets will repeatedly crash the PPMD process and sustain the Denial of Service (DoS) condition. Due to the nature of the specifically crafted packet, exploitation of this issue requires direct, adjacent connectivity to the vulnerable component. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S12, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S5, 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2.

An improper check for unusual or exceptional conditions vulnerability in Juniper Networks MX Series platforms with Trio-based MPC (Modular Port Concentrator) deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, may allow an attacker sending specific Layer 2 traffic to cause Distributed Denial of Service (DDoS) protection to trigger unexpectedly, resulting in traffic impact. Continued receipt and processing of this specific Layer 2 frames will sustain the Denial of Service (DoS) condition. An indication of compromise is to check DDOS LACP violations: user@device> show ddos-protection protocols statistics brief | match lacp This issue only affects the MX Series platforms with Trio-based MPC. No other products or platforms are affected. This issue affects: Juniper Networks Junos OS on MX Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2;

A kernel memory leak in QFX10002-32Q, QFX10002-60C, QFX10002-72Q, QFX10008, QFX10016 devices Flexible PIC Concentrators (FPCs) on Juniper Networks Junos OS allows an attacker to send genuine packets destined to the device to cause a Denial of Service (DoS) to the device. On QFX10002-32Q, QFX10002-60C, QFX10002-72Q devices the device will crash and restart. On QFX10008, QFX10016 devices, depending on the number of FPCs involved in an attack, one more more FPCs may crash and traffic through the device may be degraded in other ways, until the attack traffic stops. A reboot is required to restore service and clear the kernel memory. Continued receipt and processing of these genuine packets will create a sustained Denial of Service (DoS) condition. On QFX10008, QFX10016 devices, an indicator of compromise may be the existence of DCPFE core files. You can also monitor PFE memory utilization for incremental growth: user@qfx-RE:0% cprod -A fpc0 -c "show heap 0" | grep -i ke 0 3788a1b0 3221225048 2417120656 804104392 24 Kernel user@qfx-RE:0% cprod -A fpc0 -c "show heap 0" | grep -i ke 0 3788a1b0 3221225048 2332332200 888892848 27 Kernel This issue affects: Juniper Networks Junos OS on QFX10002-32Q, QFX10002-60C, QFX10002-72Q, QFX10008, QFX10016: 16.1 versions 16.1R1 and above prior to 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R3-S2; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R3; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2. This issue does not affect releases prior to Junos OS 16.1R1. This issue does not affect EX Series devices. This issue does not affect Junos OS Evolved.

In a Segment Routing ISIS (SR-ISIS)/MPLS environment, on Juniper Networks Junos OS and Junos OS Evolved devices, configured with ISIS Flexible Algorithm for Segment Routing and sensor-based statistics, a flap of a ISIS link in the network, can lead to a routing process daemon (RPD) crash and restart, causing a Denial of Service (DoS). Continued link flaps will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 19.4 versions prior to 19.4R1-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R2; Juniper Networks Junos OS Evolved: 20.3-EVO versions prior to 20.3R2-EVO; 20.4-EVO versions prior to 20.4R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

A vulnerability in Juniper Networks Junos OS running on the ACX5448 and ACX710 platforms may cause BFD sessions to flap when a high rate of transit ARP packets are received. This, in turn, may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. When a high rate of transit ARP packets are exceptioned to the CPU and BFD flaps, the following log messages may be seen: bfdd[15864]: BFDD_STATE_UP_TO_DOWN: BFD Session 192.168.14.3 (IFL 232) state Up -> Down LD/RD(17/19) Up time:11:38:17 Local diag: CtlExpire Remote diag: None Reason: Detect Timer Expiry. bfdd[15864]: BFDD_TRAP_SHOP_STATE_DOWN: local discriminator: 17, new state: down, interface: irb.998, peer addr: 192.168.14.3 rpd[15839]: RPD_ISIS_ADJDOWN: IS-IS lost L2 adjacency to peer on irb.998, reason: BFD Session Down bfdd[15864]: BFDD_TRAP_SHOP_STATE_UP: local discriminator: 17, new state: up, interface: irb.998, peer addr: 192.168.14.3 This issue only affects the ACX5448 Series and ACX710 Series routers. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS: 18.2 versions prior to 18.2R3-S8 on ACX5448; 18.3 versions prior to 18.3R3-S5 on ACX5448; 18.4 versions prior to 18.4R1-S6, 18.4R3-S7 on ACX5448; 19.1 versions prior to 19.1R3-S5 on ACX5448; 19.2 versions prior to 19.2R2, 19.2R3 on ACX5448; 19.3 versions prior to 19.3R3 on ACX5448; 19.4 versions prior to 19.4R3 on ACX5448; 20.1 versions prior to 20.1R2 on ACX5448; 20.2 versions prior to 20.2R2 on ACX5448 and ACX710.

A Double Free vulnerability in the software forwarding interface daemon (sfid) process of Juniper Networks Junos OS allows an adjacently-connected attacker to cause a Denial of Service (DoS) by sending a crafted ARP packet to the device. Continued receipt and processing of the crafted ARP packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX2200-C Series, EX3200 Series, EX3300 Series, EX4200 Series, EX4500 Series, EX4550 Series, EX6210 Series, EX8208 Series, EX8216 Series. 12.3 versions prior to 12.3R12-S17; 15.1 versions prior to 15.1R7-S8. This issue only affects the listed Marvell-chipset based EX Series devices. No other products or platforms are affected.

An Improper Handling of Exceptional Conditions vulnerability in route processing of Juniper Networks Junos OS on specific end-of-life (EOL) ACX Series platforms allows an attacker to crash the Forwarding Engine Board (FEB) by flapping an interface, leading to a Denial of Service (DoS). On ACX1000, ACX1100, ACX2000, ACX2100, ACX2200, ACX4000, ACX5048, and ACX5096 devices, FEB0 will crash when the primary path port of the L2 circuit IGP (Interior Gateway Protocol) on the local device goes down. This issue is seen only when 'hot-standby' mode is configured for the L2 circuit. This issue affects Junos OS on ACX1000, ACX1100, ACX2000, ACX2100, ACX2200, ACX4000, ACX5048, and ACX5096:  * all versions before 21.2R3-S9.

A Reachable Assertion vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When the device receives a specific BGP UPDATE packet, the rpd crashes and restarts. Continuous receipt of this specific packet will cause a sustained DoS condition. For the issue to occur, BGP multipath with "pause-computation-during-churn" must be configured on the device, and the attacker must send the paths via a BGP UPDATE from a established BGP peer. This issue affects: Junos OS: * All versions before 21.4R3-S7, * from 22.3 before 22.3R3-S3, * from 22.4 before 22.4R3-S5, * from 23.2 before 23.2R2, * from 23.4 before 23.4R2. Junos OS Evolved: * All versions before 21.4R3-S7-EVO, * from 22.3 before 22.3R3-S3-EVO, * from 22.4 before 22.4R3-S5-EVO, * from 23.2 before 23.2R2-EVO, * from 23.4 before 23.4R2-EVO.

A Race Condition vulnerability in Juniper Networks Junos OS LLDP implementation allows an attacker to cause LLDP to crash leading to a Denial of Service (DoS). This issue occurs when crafted LLDP packets are received by the device from an adjacent device. Multiple LACP flaps will occur after LLDP crashes. An indicator of compromise is to evaluate log file details for lldp with RLIMIT. Intervention should occur before 85% threshold of used KB versus maximum available KB memory is reached. show log messages | match RLIMIT | match lldp | last 20 Matching statement is " /kernel: %KERNEL-[number]: Process ([pid #],lldpd) has exceeded 85% of RLIMIT_DATA: " with [] as variable data to evaluate for. This issue affects: Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D200; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R1-S9, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R2-S7, 18.2R3; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D50, 18.2X75-D420; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2.

An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a logically adjacent BGP peer sending a specifically malformed BGP packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Only systems configured for Ethernet Virtual Private Networking (EVPN) signaling are vulnerable to this issue.  This issue affects iBGP and eBGP, and both IPv4 and IPv6 are affected by this vulnerability.This issue affects: Junos OS:  * all versions before 21.4R3-S11,  * from 22.2 before 22.2R3-S7,  * from 22.4 before 22.4R3-S7,  * from 23.2 before 23.2R2-S4,  * from 23.4 before 23.4R2-S5,  * from 24.2 before 24.2R2-S1,  * from 24.4 before 24.4R1-S3, 24.4R2;  Junos OS Evolved:  * all versions before 22.2R3-S7-EVO,  * from 22.4-EVO before 22.4R3-S7-EVO,  * from 23.2-EVO before 23.2R2-S4-EVO,  * from 23.4-EVO before 23.4R2-S5-EVO,  * from 24.2-EVO before 24.2R2-S1-EVO,  * from 24.4-EVO before 24.4R1-S3-EVO, 24.4R2-EVO.