On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. By simulating a specific BGP session restart, an attacker can repeatedly crash the RPD process causing prolonged denial of service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S8; 17.1 versions prior to 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R2. Junos OS releases prior to 16.1R1 are not affected.

A firewall bypass vulnerability in the proxy ARP service of Juniper Networks Junos OS allows an attacker to cause a high CPU condition leading to a Denial of Service (DoS). This issue affects only IPv4. Affected releases are Juniper Networks Junos OS: 12.1X46 versions above and including 12.1X46-D25 prior to 12.1X46-D71, 12.1X46-D73 on SRX Series; 12.3X48 versions prior to 12.3X48-D50 on SRX Series; 15.1X49 versions prior to 15.1X49-D75 on SRX Series.

This issue only affects devices with three (3) or more MPC10's installed in a single chassis with OSPF enabled and configured on the device. An Insufficient Resource Pool weakness allows an attacker to cause the device's Open Shortest Path First (OSPF) states to transition to Down, resulting in a Denial of Service (DoS) attack. This attack requires a relatively large number of specific Internet Mixed (IMIXed) types of genuine and valid IPv6 packets to be transferred by the attacker in a relatively short period of time, across three or more PFE's on the device at the same time. Continued receipt of the traffic sent by the attacker will continue to cause OSPF to remain in the Down starting state, or flap between other states and then again to Down, causing a persistent Denial of Service. This attack will affect all IPv4, and IPv6 traffic served by the OSPF routes once the OSPF states transition to Down. This issue affects: Juniper Networks Junos OS on MX480, MX960, MX2008, MX2010, MX2020: 18.1 versions prior to 18.1R2-S4, 18.1R3-S5; 18.1X75 version 18.1X75-D10 and later versions; 18.2 versions prior to 18.2R1-S5, 18.2R2-S3, 18.2R3; 18.2X75 versions prior to 18.2X75-D50; 18.3 versions prior to 18.3R1-S4, 18.3R2, 18.3R3; 18.4 versions prior to 18.4R1-S2, 18.4R2.

Under certain heavy traffic conditions srxpfe process can crash and result in a denial of service condition for the SRX1500 device. Repeated crashes of the srxpfe can result in an extended denial of service condition. The SRX device may fail to forward traffic when this condition occurs. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D170 on SRX1500; 17.3 versions prior to 17.3R3-S7 on SRX1500; 17.4 versions prior to 17.4R2-S8, 17.4R3 on SRX1500; 18.1 versions prior to 18.1R3-S8 on SRX1500; 18.2 versions prior to 18.2R3 on SRX1500; 18.3 versions prior to 18.3R2 on SRX1500; 18.4 versions prior to 18.4R2 on SRX1500.

On MX Series, when the SIP ALG is enabled, receipt of a certain malformed SIP packet may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending a crafted SIP packet, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on MX Series: 16.1 versions prior to 16.1R7-S5; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R3-S6 ; 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S3; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2.

In Point to MultiPoint (P2MP) scenarios within established sessions between network or adjacent neighbors the improper use of a source to destination copy write operation combined with a Stack-based Buffer Overflow on certain specific packets processed by the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved sent by a remote unauthenticated network attacker causes the RPD to crash causing a Denial of Service (DoS). Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.2R1. Juniper Networks Junos OS Evolved 20.1 versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R3-EVO; 20.3 versions prior to 20.3R2-EVO.

An Uncontrolled Resource Consumption vulnerability in TCP processing on the Routing Engine (RE) of Juniper Networks Junos OS allows an unauthenticated network-based attacker to send crafted TCP packets destined to the device, resulting in an MBUF leak that ultimately leads to a Denial of Service (DoS). The system does not recover automatically and must be manually restarted to restore service. This issue occurs when crafted TCP packets are sent directly to a configured IPv4 or IPv6 interface on the device. Transit traffic will not trigger this issue. MBUF usage can be monitored through the use of the 'show system buffers' command. For example: user@junos> show system buffers | refresh 5 4054/566/4620 mbufs in use (current/cache/total) ... 4089/531/4620 mbufs in use (current/cache/total) ... 4151/589/4740 mbufs in use (current/cache/total) ... 4213/527/4740 mbufs in use (current/cache/total) This issue affects Juniper Networks Junos OS: 12.3 version 12.3R12-S19 and later versions; 15.1 version 15.1R7-S10 and later versions; 17.3 version 17.3R3-S12 and later versions; 18.4 version 18.4R3-S9 and later versions; 19.1 version 19.1R3-S7 and later versions; 19.2 version 19.2R3-S3 and later versions; 19.3 version 19.3R2-S7, 19.3R3-S3 and later versions prior to 19.3R3-S7; 19.4 version 19.4R2-S7, 19.4R3-S5 and later versions prior to 19.4R3-S10; 20.1 version 20.1R3-S1 and later versions; 20.2 version 20.2R3-S2 and later versions prior to 20.2R3-S6; 20.3 version 20.3R3-S1 and later versions prior to 20.3R3-S6; 20.4 version 20.4R2-S2, 20.4R3 and later versions prior to 20.4R3-S5; 21.1 version 21.1R2 and later versions prior to 21.1R3-S4; 21.2 version 21.2R1-S1, 21.2R2 and later versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2; 22.3 versions prior to 22.3R1-S1, 22.3R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Networks Junos OS on MX Series platforms with MPC10/MPC11 line cards, allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). Devices are only vulnerable when the Suspicious Control Flow Detection (scfd) feature is enabled. Upon enabling this specific feature, an attacker sending specific traffic is causing memory to be allocated dynamically and it is not freed. Memory is not freed even after deactivating this feature. Sustained processing of such traffic will eventually lead to an out of memory condition that prevents all services from continuing to function, and requires a manual restart to recover. The FPC memory usage can be monitored using the CLI command "show chassis fpc". On running the above command, the memory of AftDdosScfdFlow can be observed to detect the memory leak. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 20.2R3-S5; 20.3 version 20.3R1 and later versions.

A Missing Release of Memory after Effective Lifetime vulnerability in the Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In an IPsec VPN environment, a memory leak will be seen if a DH or ECDH group is configured. Eventually the flowd process will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

A Buffer Overflow vulnerability in SIP ALG of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On all MX Series and SRX Series platform with SIP ALG enabled, when a malformed SIP packet is received, the flow processing daemon (flowd) will crash and restart. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on SRX Series.

An Improper Validation of Array Index vulnerability in the SIP ALG of Juniper Networks Junos OS on SRX 5000 Series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an attacker sends an SIP packets with a malformed SDP field then the SIP ALG can not process it which will lead to an FPC crash and restart. Continued receipt of these specific packets will lead to a sustained Denial of Service. This issue can only occur when both below mentioned conditions are fulfilled: 1. Call distribution needs to be enabled: [security alg sip enable-call-distribution] 2. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX, and MX with SPC3 use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX 5000 Series: 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R1-S1, 22.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

An Uncontrolled Resource Consumption vulnerability in the PFE management daemon (evo-pfemand) of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause an FPC crash leading to a Denial of Service (DoS). When a specific SNMP GET operation or a specific CLI command is executed this will cause a GUID resource leak, eventually leading to exhaustion and result in an FPC crash and reboot. GUID exhaustion will trigger a syslog message like one of the following for example: evo-pfemand[<pid>]: get_next_guid: Ran out of Guid Space ... evo-aftmand-zx[<pid>]: get_next_guid: Ran out of Guid Space ... This leak can be monitored by running the following command and taking note of the value in the rightmost column labeled Guids: user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3448 0 3448 re0 evo-pfemand net::juniper::interfaces::IFLId 0 561 0 561 user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3784 0 3784 re0 evo-pfemand net::juniper::interfaces::IFLId 0 647 0 647 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S3-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO versions prior to 21.2R3-S4-EVO; 21.3-EVO version 21.3R1-EVO and later versions; 21.4-EVO versions prior to 21.4R2-EVO.

An Improper Check or Handling of Exceptional Conditions vulnerability in the IPsec library of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause Denial of Service (DoS). On all MX platforms with MS-MPC or MS-MIC card, when specific IPv4 packets are processed by an IPsec6 tunnel, the Multiservices PIC Management Daemon (mspmand) process will core and restart. This will lead to FPC crash. Traffic flow is impacted while mspmand restarts. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue only occurs if an IPv4 address is not configured on the multiservice interface. This issue affects: Juniper Networks Junos OS on MX Series All versions prior to 19.4R3-S9; 20.1 version 20.1R3-S5 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2.

An Out-of-Bounds Write vulnerability in the H.323 ALG of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all MX Series and SRX Series platform, when H.323 ALG is enabled and specific H.323 packets are received simultaneously, a flow processing daemon (flowd) crash will occur. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series All versions prior to 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2.

A vulnerability in class-of-service (CoS) queue management in Juniper Networks Junos OS on the ACX2K Series devices allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). Specific packets are being incorrectly routed to a queue used for other high-priority traffic such as BGP, PIM, ICMP, ICMPV6 ND and ISAKMP. Due to this misclassification of traffic, receipt of a high rate of these specific packets will cause delays in the processing of other traffic, leading to a Denial of Service (DoS). Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX2K Series: All versions prior to 19.4R3-S9; All 20.2 versions; 20.3 versions prior to 20.3R3-S6 on ACX2K Series; 20.4 versions prior to 20.4R3-S4 on ACX2K Series; All 21.1 versions; 21.2 versions prior to 21.2R3-S3 on ACX2K Series. Note: This issues affects legacy ACX2K Series PPC-based devices. This platform reached Last Supported Version (LSV) as of the Junos OS 21.2 Release.

An Improper Locking vulnerability in the SIP ALG of Juniper Networks Junos OS on MX Series with MS-MPC or MS-MIC card and SRX Series allows an unauthenticated, network-based attacker to cause a flow processing daemon (flowd) crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue occurs when SIP ALG is enabled and specific SIP messages are processed simultaneously. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on MX Series, or SRX Series.

An Improper Check for Unusual or Exceptional Conditions vulnerability in BGP route processing of Juniper Networks Junos OS and Junos OS Evolved allows an attacker to cause Routing Protocol Daemon (RPD) crash by sending a BGP route with invalid next-hop resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems without import policy configured. This issue affects: Juniper Networks Junos OS 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. Juniper Networks Junos OS Evolved 21.4-EVO versions prior to 21.4R2-S2-EVO, 21.4R3-EVO; 22.1-EVO versions prior to 22.1R1-S2-EVO, 22.1R2-EVO; 22.2-EVO versions prior to 22.2R1-S1-EVO, 22.2R2-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 21.1R1. Juniper Networks Junos OS Evolved versions prior to 21.3R1-EVO.

An Out-of-Bounds Write vulnerability in Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On SRX Series devices using Unified Policies with IPv6, when a specific IPv6 packet goes through a dynamic-application filter which will generate an ICMP deny message, the flowd core is observed and the PFE is restarted. This issue affects: Juniper Networks Junos OS on SRX Series: 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.

An issue was discovered in Embedthis GoAhead before 4.0.1 and Appweb before 7.0.2. The server mishandles some HTTP request fields associated with time, which results in a NULL pointer dereference, as demonstrated by If-Modified-Since or If-Unmodified-Since with a month greater than 11.

An issue was discovered in Embedthis GoAhead before 4.0.1 and Appweb before 7.0.2. An HTTP POST request with a specially crafted "Host" header field may cause a NULL pointer dereference and thus cause a denial of service, as demonstrated by the lack of a trailing ']' character in an IPv6 address.

Receipt of a specifically malformed IPv6 packet processed by the router may trigger a line card reset: processor exception 0x68616c74 (halt) in task: scheduler. The line card will reboot and recover without user interaction. However, additional specifically malformed packets may cause follow-on line card resets and lead to an extended service outage. This issue only affects E Series routers with IPv6 licensed and enabled. Routers not configured to process IPv6 traffic are unaffected by this vulnerability. Juniper SIRT is not aware of any malicious exploitation of this vulnerability. No other Juniper Networks products or platforms are affected by this issue.

An Improper Check for Unusual or Exceptional Conditions vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause rpd to crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when NETCONF and gRPC are enabled, and a specific query is executed via Dynamic Rendering (DREND), rpd will crash and restart. Continuous execution of this specific query will cause a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS * 22.2 versions earlier than 22.2R2-S2, 22.2R3; * 22.3 versions earlier than 22.3R2, 22.3R3. Juniper Networks Junos OS Evolved * 22.2 versions earlier than 22.2R2-S2-EVO, 22.2R3-EVO; * 22.3 versions earlier than 22.3R2-EVO, 22.3R3-EVO. This issue does not affect Juniper Networks: Junos OS versions earlier than 22.2R1; Junos OS Evolved versions earlier than 22.2R1-EVO.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If an attacker sends high rate of specific ICMP traffic to a device with VXLAN configured, this causes a deadlock of the PFE and results in the device becoming unresponsive. A manual restart will be required to recover the device. This issue only affects EX4100, EX4400, EX4600, QFX5000 Series devices. This issue affects: Juniper Networks Junos OS * 21.4R3 versions earlier than 21.4R3-S4; * 22.1R3 versions earlier than 22.1R3-S3; * 22.2R2 versions earlier than 22.2R3-S1; * 22.3 versions earlier than 22.3R2-S2, 22.3R3; * 22.4 versions earlier than 22.4R2; * 23.1 versions earlier than 23.1R2.

An Improper Validation of Syntactic Correctness of Input vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all Junos OS MX Series and SRX Series platforms, when SIP ALG is enabled, and a specific SIP packet is received and processed, NAT IP allocation fails for genuine traffic, which causes Denial of Service (DoS). Continuous receipt of this specific SIP ALG packet will cause a sustained DoS condition. NAT IP usage can be monitored by running the following command. user@srx> show security nat resource-usage source-pool <source_pool_name> Pool name: source_pool_name .. Address Factor-index Port-range Used Avail Total Usage X.X.X.X 0 Single Ports 50258 52342 62464 96% <<<<< - Alg Ports 0 2048 2048 0% This issue affects: Juniper Networks Junos OS on MX Series and SRX Series * All versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). If a BGP update is received over an established BGP session which contains a tunnel encapsulation attribute with a specifically malformed TLV, rpd will crash and restart. This issue affects Juniper Networks Junos OS: * 20.4 versions 20.4R1 and later versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2; Junos OS Evolved: * 20.4-EVO versions 20.4R1-EVO and later versions earlier than 20.4R3-S9-EVO; * 21.2-EVO versions earlier than 21.2R3-S7-EVO; * 21.3-EVO versions earlier than 21.3R3-S5-EVO; * 21.4-EVO versions earlier than 21.4R3-S5-EVO; * 22.1-EVO versions earlier than 22.1R3-S4-EVO; * 22.2-EVO versions earlier than 22.2R3-S3-EVO; * 22.3-EVO versions earlier than 22.3R3-S1-EVO; * 22.4-EVO versions earlier than 22.4R3-EVO; * 23.2-EVO versions earlier than 23.2R1-S2-EVO, 23.2R2-EVO; This issue does not affect Juniper Networks * Junos OS versions earlier than 20.4R1; * Junos OS Evolved versions earlier than 20.4R1-EVO. This is a related but separate issue than the one described in JSA79095.

The rpd daemon in Juniper Junos OS before 12.1X44-D60, 12.1X46 before 12.1X46-D45, 12.1X47 before 12.1X47-D30, 12.3 before 12.3R9, 12.3X48 before 12.3X48-D20, 13.2 before 13.2R7, 13.2X51 before 13.2X51-D40, 13.3 before 13.3R6, 14.1 before 14.1R4, and 14.2 before 14.2R2, when configured with BGP-based L2VPN or VPLS, allows remote attackers to cause a denial of service (daemon restart) via a crafted L2VPN family BGP update.

A vulnerability in the NETISR network queue functionality of Juniper Networks Junos OS kernel allows an attacker to cause a Denial of Service (DoS) by sending crafted genuine packets to a device. During an attack, the routing protocol daemon (rpd) CPU may reach 100% utilization, yet FPC CPUs forwarding traffic will operate normally. This attack occurs when the attackers' packets are sent over an IPv4 unicast routing equal-cost multi-path (ECMP) unilist selection. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. An indicator of compromise may be to monitor NETISR drops in the network with the assistance of JTAC. Please contact JTAC for technical support for further guidance. This issue affects: Juniper Networks Junos OS 17.3 version 17.3R3-S9 and later versions prior to 17.3R3-S12; 17.4 version 17.4R3-S3 and later versions prior to 17.4R3-S5; 18.1 version 18.1R3-S11 and later versions prior to 18.1R3-S13; 18.2 version 18.2R3-S6 and later versions; 18.3 version 18.3R3-S4 and later versions prior to 18.3R3-S5; 18.4 version 18.4R3-S5 and later versions prior to 18.4R3-S9; 19.1 version 19.1R3-S3 and later versions prior to 19.1R3-S7. This issue does not affect Juniper Networks Junos OS versions prior to 17.3R3-S9. This issue does not affect Juniper Networks Junos OS Evolved.

A vulnerability in Juniper Networks Junos OS on SRX Series, allows a network-based unauthenticated attacker to cause a Denial of Service (DoS) by sending a specific fragmented packet to the device, resulting in a flowd process crash, which is responsible for packet forwarding. Continued receipt and processing of this specific packet will create a sustained DoS condition. This issue only affects SRX Series when 'preserve-incoming-fragment-size' feature is enabled. This issue affects Juniper Networks Junos OS on SRX Series: 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2. This issue does not affect Juniper Networks Junos OS prior to 17.3R1.

A Buffer Overflow vulnerability in the PFE of Juniper Networks Junos OS on SRX series allows an unauthenticated network based attacker to cause a Denial of Service (DoS). The PFE will crash when specific traffic is scanned by Enhanced Web Filtering safe-search feature of UTM (Unified Threat management). Continued receipt of this specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: 20.2 versions prior to 20.2R3-S4 on SRX Series; 20.3 versions prior to 20.3R3-S3 on SRX Series; 20.4 versions prior to 20.4R3-S3 on SRX Series; 21.1 versions prior to 21.1R3-S1 on SRX Series; 21.2 versions prior to 21.2R2-S2, 21.2R3 on SRX Series; 21.3 versions prior to 21.3R2 on SRX Series; 21.4 versions prior to 21.4R2 on SRX Series. This issue does not affect Juniper Networks Junos OS versions prior to 20.2R1.

named in ISC BIND 9.x before 9.9.8-P4 and 9.10.x before 9.10.3-P4 allows remote attackers to cause a denial of service (assertion failure and daemon exit) via a crafted signature record for a DNAME record, related to db.c and resolver.c.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). If a BGP update message is received over an established BGP session, and that message contains a specific, optional transitive attribute, this session will be torn down with an update message error. This issue cannot propagate beyond an affected system as the processing error occurs as soon as the update is received. This issue is exploitable remotely as the respective attribute will propagate through unaffected systems and intermediate AS (if any). Continuous receipt of a BGP update containing this attribute will create a sustained Denial of Service (DoS) condition. Since this issue only affects 22.3R1, Juniper strongly encourages customers to move to 22.3R1-S1. Juniper SIRT felt that the need to promptly warn customers about this issue affecting the 22.3R1 versions of Junos OS and Junos OS Evolved warranted an Out of Cycle JSA. This issue affects: Juniper Networks Junos OS version 22.3R1. Juniper Networks Junos OS Evolved version 22.3R1-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 22.3R1. Juniper Networks Junos OS Evolved versions prior to 22.3R1-EVO.

Embedthis Appweb, as used in J-Web in Juniper Junos OS before 12.1X44-D60, 12.1X46 before 12.1X46-D45, 12.1X47 before 12.1X47-D30, 12.3 before 12.3R10, 12.3X48 before 12.3X48-D20, 13.2X51 before 13.2X51-D20, 13.3 before 13.3R8, 14.1 before 14.1R6, and 14.2 before 14.2R5, allows remote attackers to cause a denial of service (J-Web crash) via unspecified vectors.

An Improper Validation of Specified Index, Position, or Offset in Input vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). On SRX5000 Series with SPC3, SRX4000 Series, and vSRX, when PowerMode IPsec is configured and a malformed ESP packet matching an established IPsec tunnel is received the PFE crashes. This issue affects Juniper Networks Junos OS on SRX5000 Series with SPC3, SRX4000 Series, and vSRX: All versions prior to 19.4R2-S6, 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S4; 20.3 versions prior to 20.3R3-S3; 20.4 versions prior to 20.4R3-S2; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R1-S2, 21.3R2.

On QFX10000 Series devices using Juniper Networks Junos OS when configured as transit IP/MPLS penultimate hop popping (PHP) nodes with link aggregation group (LAG) interfaces, an Improper Validation of Specified Index, Position, or Offset in Input weakness allows an attacker sending certain IP packets to cause multiple interfaces in the LAG to detach causing a Denial of Service (DoS) condition. Continued receipt and processing of these packets will sustain the Denial of Service. This issue affects IPv4 and IPv6 packets. Packets of either type can cause and sustain the DoS event. These packets can be destined to the device or be transit packets. On devices such as the QFX10008 with line cards, line cards can be restarted to restore service. On devices such as the QFX10002 you can restart the PFE service, or reboot device to restore service. This issue affects: Juniper Networks Junos OS on QFX10000 Series: All versions prior to 15.1R7-S11; 18.4 versions prior to 18.4R2-S10, 18.4R3-S10; 19.1 versions prior to 19.1R3-S8; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S1. An indicator of compromise may be seen by issuing the command: request pfe execute target fpc0 command "show jspec pechip[3] registers ps l2_node 10" timeout 0 | refresh 1 | no-more and reviewing for backpressured output; for example: GOT: 0x220702a8 pe.ps.l2_node[10].pkt_cnt 00000076 GOT: 0x220702b4 pe.ps.l2_node[10].backpressured 00000002 <<<< STICKS HERE and requesting detail on the pepic wanio: request pfe execute target fpc0 command "show pepic 0 wanio-info" timeout 0 | no-more | match xe-0/0/0:2 GOT: 3 xe-0/0/0:2 10 6 3 0 1 10 189 10 0x6321b088 <<< LOOK HERE as well as looking for tail drops looking at the interface queue, for example: show interfaces queue xe-0/0/0:2 resulting in: Transmitted: Total-dropped packets: 1094137 0 pps << LOOK HERE

An Out-of-bounds Read vulnerability in Juniper Networks Junos OS and Junos OS Evolved's routing protocol daemon (rpd) allows an unauthenticated, network-based attacker to send malformed BGP packets to a device configured with packet receive trace options enabled to crash rpd. This issue affects: Junos OS:  * from 21.2R3-S8 before 21.2R3-S9,  * from 21.4R3-S7 before 21.4R3-S9,  * from 22.2R3-S4 before 22.2R3-S5,  * from 22.3R3-S2 before 22.3R3-S4,  * from 22.4R3 before 22.4R3-S5,  * from 23.2R2 before 23.2R2-S2,  * from 23.4R1 before 23.4R2-S1,  * from 24.2R1 before 24.2R1-S1, 24.2R2. Junos OS Evolved: * from 21.4R3-S7-EVO before 21.4R3-S9-EVO,  * from 22.2R3-S4-EVO before 22.2R3-S5-EVO,  * from 22.3R3-S2-EVO before 22.3R3-S4-EVO,  * from 22.4R3-EVO before 22.4R3-S5-EVO,  * from 23.2R2-EVO before 23.2R2-S2-EVO,  * from 23.4R1-EVO before 23.4R2-S1-EVO,  * from 24.2R1-EVO before 24.2R1-S2-EVO, 24.2R2-EVO. This issue requires a BGP session to be established. This issue can propagate and multiply through multiple ASes until reaching vulnerable devices. This issue affects iBGP and eBGP. This issue affects IPv4 and IPv6. An indicator of compromise may be the presence of malformed update messages in a neighboring AS which is unaffected by this issue: For example, by issuing the command on the neighboring device:  show log messages Reviewing for similar messages from devices within proximity to each other may indicate this malformed packet is propagating:   rpd[<pid>]: Received malformed update from <IP address> (External AS <AS#>) and   rpd[<pid>]: Malformed Attribute

An Improper Following of Specification by Caller vulnerability in web management (J-Web, Captive Portal, 802.1X, Juniper Secure Connect (JSC) of Juniper Networks Junos OS on SRX Series, EX Series, MX240, MX480, MX960, QFX5120 Series, allows an unauthenticated, network-based attacker, sending genuine traffic targeted to the device to cause the CPU to climb until the device becomes unresponsive. Continuous receipt of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Junos OS:  * All versions before 21.4R3-S9, * from 22.2 before 22.2R3-S5, * from 22.4 before 22.4R3-S4, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S3, * from 24.2 before 24.2R1-S1, 24.2R2. An indicator of compromise is to review the CPU % of the httpd process in the CLI: e.g.   show system processes extensive | match httpd  PID nobody       52   0   20M    191M select   2   0:01   80.00% httpd{httpd} <<<<< the percentage of httpd usage if high may be an indicator

A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Tunnel Driver (jtd) of Juniper Networks Junos OS Evolved allows an unauthenticated network-based attacker to cause Denial of Service.  Receipt of specifically malformed IPv6 packets, destined to the device, causes kernel memory to not be freed, resulting in memory exhaustion leading to a system crash and Denial of Service (DoS). Continuous receipt and processing of these packets will continue to exhaust kernel memory, creating a sustained Denial of Service (DoS) condition. This issue only affects systems configured with IPv6. This issue affects Junos OS Evolved:  * from 22.4-EVO before 22.4R3-S5-EVO,  * from 23.2-EVO before 23.2R2-S2-EVO,  * from 23.4-EVO before 23.4R2-S2-EVO,  * from 24.2-EVO before 24.2R1-S2-EVO, 24.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 22.4R1-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the pfe (packet forwarding engine) of Juniper Networks Junos OS on MX Series causes a port within a pool to be blocked leading to Denial of Service (DoS). In a DS-Lite (Dual-Stack Lite) and NAT (Network Address Translation) scenario, when crafted IPv6 traffic is received and prefix-length is set to 56, the ports assigned to the user will not be freed.  Eventually, users cannot establish new connections. Affected FPC/PIC need to be manually restarted to recover. Following is the command to identify the issue:      user@host> show services nat source port-block      Host_IP                     External_IP                   Port_Block      Ports_Used/       Block_State/                                                               Range           Ports_Total       Left_Time(s)     2001::                        x.x.x.x                     58880-59391     256/256*1         Active/-       >>>>>>>>port still usedThis issue affects Junos OS on MX Series:  * from 21.2 before 21.2R3-S8,  * from 21.4 before 21.4R3-S7,  * from 22.1 before 22.1R3-S6,  * from 22.2 before 22.2R3-S4,  * from 22.3 before 22.3R3-S3,  * from 22.4 before 22.4R3-S2,  * from 23.2 before 23.2R2-S1,  * from 23.4 before 23.4R1-S2, 23.4R2. This issue does not affect versions before 20.2R1.

Juniper Junos OS before 13.2X51-D36, 14.1X53 before 14.1X53-D25, and 15.2 before 15.2R1 on EX4300 series switches allow remote attackers to cause a denial of service (network loop and bandwidth consumption) via unspecified vectors related to Spanning Tree Protocol (STP) traffic.

Juniper Junos OS before 12.1X44-D55, 12.1X46 before 12.1X46-D40, 12.1X47 before 12.1X47-D25, 12.3 before 12.3R10, 12.3X48 before 12.3X48-D20, 13.2 before 13.2R8, 13.2X51 before 13.2X51-D40, 13.3 before 13.3R7, 14.1 before 14.1R5, 14.1X53 before 14.1X53-D18 or 14.1X53-D30, 14.1X55 before 14.1X55-D25, 14.2 before 14.2R4, 15.1 before 15.1R2, and 15.1X49 before 15.1X49-D10 allow remote attackers to cause a denial of service via a malformed IGMPv3 packet, aka a "multicast denial of service."

Receipt of a specific MPLS or IPv6 packet on the core facing interface of an MX Series device configured for Broadband Edge (BBE) service may trigger a kernel crash (vmcore), causing the device to reboot. The issue is specific to the processing of packets destined to BBE clients connected to MX Series subscriber management platforms. This issue affects MX Series running Juniper Networks Junos OS: 17.2 versions starting from17.2R2-S6, 17.2R3 and later releases, prior to 17.2R3-S3; 17.3 versions starting from 17.3R2-S4, 17.3R3-S2 and later releases, prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions starting from 17.4R2 and later releases, prior to 17.4R2-S7,17.4R3; 18.1 versions starting from 18.1R2-S3, 18.1R3 and later releases, prior to 18.1R3-S6; 18.2 versions starting from18.2R1-S1, 18.2R2 and later releases, prior to 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D51, 18.2X75-D60; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R2-S6.

IPv6 sendd in Juniper Junos 12.1X44 before 12.1X44-D51, 12.1X46 before 12.1X46-D36, 12.1X46 before 12.1X46-D40, 12.1X47 before 12.1X47-D25, 12.3 before 12.3R10, 12.3X48 before 12.3X48-D20, 13.2 before 13.2R8, 13.3 before 13.3R6, 14.1 before 14.1R5, 14.2 before 14.2R3, 15.1 before 15.1R1, and 15.1X49 before 15.1X49-D20, when the "set protocols neighbor-discovery secure security-level default" option is configured, allows remote attackers to cause a denial of service (CPU consumption) via a crafted Secure Neighbor Discovery (SEND) Protocol packet.

On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a certain sequence of BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. Repeated crashes of the RPD process can cause prolonged Denial of Service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S3; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.2X75 versions prior to 17.2X75-D105; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R1-S7, 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D30; 18.3 versions prior to 18.3R1-S4, 18.3R2. Junos OS releases prior to 16.1R1 are not affected.

The Juniper EX4600, QFX3500, QFX3600, and QFX5100 switches with Junos 13.2X51-D15 through 13.2X51-D25, 13.2X51 before 13.2X51-D30, and 14.1X53 before 14.1X53-D10 allows remote attackers to cause a denial of service (CPU consumption) via unspecified vectors.