In the Linux kernel, the following vulnerability has been resolved: hv_netvsc: Fix race condition between netvsc_probe and netvsc_remove In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the VMBus channel"), napi_disable was getting called for all channels, including all subchannels without confirming if they are enabled or not. This caused hv_netvsc getting hung at napi_disable, when netvsc_probe() has finished running but nvdev->subchan_work has not started yet. netvsc_subchan_work() -> rndis_set_subchannel() has not created the sub-channels and because of that netvsc_sc_open() is not running. netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which netvsc_subchan_work did not run. netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the opposite. Now during netvsc_device_remove(), when napi_disable is called for those subchannels, napi_disable gets stuck on infinite msleep. This fix addresses this problem by ensuring that napi_disable() is not getting called for non-enabled NAPI struct. But netif_napi_del() is still necessary for these non-enabled NAPI struct for cleanup purpose. Call trace: [ 654.559417] task:modprobe state:D stack: 0 pid: 2321 ppid: 1091 flags:0x00004002 [ 654.568030] Call Trace: [ 654.571221] <TASK> [ 654.573790] __schedule+0x2d6/0x960 [ 654.577733] schedule+0x69/0xf0 [ 654.581214] schedule_timeout+0x87/0x140 [ 654.585463] ? __bpf_trace_tick_stop+0x20/0x20 [ 654.590291] msleep+0x2d/0x40 [ 654.593625] napi_disable+0x2b/0x80 [ 654.597437] netvsc_device_remove+0x8a/0x1f0 [hv_netvsc] [ 654.603935] rndis_filter_device_remove+0x194/0x1c0 [hv_netvsc] [ 654.611101] ? do_wait_intr+0xb0/0xb0 [ 654.615753] netvsc_remove+0x7c/0x120 [hv_netvsc] [ 654.621675] vmbus_remove+0x27/0x40 [hv_vmbus]

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to truncate meta inode pages forcely Below race case can cause data corruption: Thread A GC thread - gc_data_segment - ra_data_block - locked meta_inode page - f2fs_inplace_write_data - invalidate_mapping_pages : fail to invalidate meta_inode page due to lock failure or dirty|writeback status - f2fs_submit_page_bio : write last dirty data to old blkaddr - move_data_block - load old data from meta_inode page - f2fs_submit_page_write : write old data to new blkaddr Because invalidate_mapping_pages() will skip invalidating page which has unclear status including locked, dirty, writeback and so on, so we need to use truncate_inode_pages_range() instead of invalidate_mapping_pages() to make sure meta_inode page will be dropped.

In the Linux kernel, the following vulnerability has been resolved: tls: fix race between async notify and socket close The submitting thread (one which called recvmsg/sendmsg) may exit as soon as the async crypto handler calls complete() so any code past that point risks touching already freed data. Try to avoid the locking and extra flags altogether. Have the main thread hold an extra reference, this way we can depend solely on the atomic ref counter for synchronization. Don't futz with reiniting the completion, either, we are now tightly controlling when completion fires.

In the Linux kernel, the following vulnerability has been resolved: wireguard: receive: annotate data-race around receiving_counter.counter Syzkaller with KCSAN identified a data-race issue when accessing keypair->receiving_counter.counter. Use READ_ONCE() and WRITE_ONCE() annotations to mark the data race as intentional. BUG: KCSAN: data-race in wg_packet_decrypt_worker / wg_packet_rx_poll write to 0xffff888107765888 of 8 bytes by interrupt on cpu 0: counter_validate drivers/net/wireguard/receive.c:321 [inline] wg_packet_rx_poll+0x3ac/0xf00 drivers/net/wireguard/receive.c:461 __napi_poll+0x60/0x3b0 net/core/dev.c:6536 napi_poll net/core/dev.c:6605 [inline] net_rx_action+0x32b/0x750 net/core/dev.c:6738 __do_softirq+0xc4/0x279 kernel/softirq.c:553 do_softirq+0x5e/0x90 kernel/softirq.c:454 __local_bh_enable_ip+0x64/0x70 kernel/softirq.c:381 __raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline] _raw_spin_unlock_bh+0x36/0x40 kernel/locking/spinlock.c:210 spin_unlock_bh include/linux/spinlock.h:396 [inline] ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline] wg_packet_decrypt_worker+0x6c5/0x700 drivers/net/wireguard/receive.c:499 process_one_work kernel/workqueue.c:2633 [inline] ... read to 0xffff888107765888 of 8 bytes by task 3196 on cpu 1: decrypt_packet drivers/net/wireguard/receive.c:252 [inline] wg_packet_decrypt_worker+0x220/0x700 drivers/net/wireguard/receive.c:501 process_one_work kernel/workqueue.c:2633 [inline] process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706 worker_thread+0x525/0x730 kernel/workqueue.c:2787 ...

In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: fix performance regression in swap operation The patch "netfilter: ipset: fix race condition between swap/destroy and kernel side add/del/test", commit 28628fa9 fixes a race condition. But the synchronize_rcu() added to the swap function unnecessarily slows it down: it can safely be moved to destroy and use call_rcu() instead. Eric Dumazet pointed out that simply calling the destroy functions as rcu callback does not work: sets with timeout use garbage collectors which need cancelling at destroy which can wait. Therefore the destroy functions are split into two: cancelling garbage collectors safely at executing the command received by netlink and moving the remaining part only into the rcu callback.

In the Linux kernel, the following vulnerability has been resolved: quota: Fix potential NULL pointer dereference Below race may cause NULL pointer dereference P1 P2 dquot_free_inode quota_off drop_dquot_ref remove_dquot_ref dquots = i_dquot(inode) dquots = i_dquot(inode) srcu_read_lock dquots[cnt]) != NULL (1) dquots[type] = NULL (2) spin_lock(&dquots[cnt]->dq_dqb_lock) (3) .... If dquot_free_inode(or other routines) checks inode's quota pointers (1) before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer dereference will be triggered. So let's fix it by using a temporary pointer to avoid this issue.

Race condition in the ext4_file_write_iter function in fs/ext4/file.c in the Linux kernel through 3.17 allows local users to cause a denial of service (file unavailability) via a combination of a write action and an F_SETFL fcntl operation for the O_DIRECT flag.

In the Linux kernel, the following vulnerability has been resolved: blk-mq: fix IO hang from sbitmap wakeup race In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered with the following blk_mq_get_driver_tag() in case of getting driver tag failure. Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime blk_mq_mark_tag_wait() can't get driver tag successfully. This issue can be reproduced by running the following test in loop, and fio hang can be observed in < 30min when running it on my test VM in laptop. modprobe -r scsi_debug modprobe scsi_debug delay=0 dev_size_mb=4096 max_queue=1 host_max_queue=1 submit_queues=4 dev=`ls -d /sys/bus/pseudo/drivers/scsi_debug/adapter*/host*/target*/*/block/* | head -1 | xargs basename` fio --filename=/dev/"$dev" --direct=1 --rw=randrw --bs=4k --iodepth=1 \ --runtime=100 --numjobs=40 --time_based --name=test \ --ioengine=libaio Fix the issue by adding one explicit barrier in blk_mq_mark_tag_wait(), which is just fine in case of running out of tag.

A race condition was found in the Linux kernel's scsi device driver in lpfc_unregister_fcf_rescan() function. This can result in a null pointer dereference issue, possibly leading to a kernel panic or denial of service issue.

A race condition was found in the Linux kernel's media/dvb-core in dvbdmx_write() function. This can result in a null pointer dereference issue, possibly leading to a kernel panic or denial of service issue.

A race condition was found in the Linux kernel's drm/exynos device driver in exynos_drm_crtc_atomic_disable() function. This can result in a null pointer dereference issue, possibly leading to a kernel panic or denial of service issue.

A race condition was found in the Linux kernel's sound/hda device driver in snd_hdac_regmap_sync() function. This can result in a null pointer dereference issue, possibly leading to a kernel panic or denial of service issue.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Disable DMCUB timeout for DCN35 [Why] DMCUB can intermittently take longer than expected to process commands. Old ASIC policy was to continue while logging a diagnostic error - which works fine for ASIC without IPS, but with IPS this could lead to a race condition where we attempt to access DCN state while it's inaccessible, leading to a system hang when the NIU port is not disabled or register accesses that timeout and the display configuration in an undefined state. [How] We need to investigate why these accesses take longer than expected, but for now we should disable the timeout on DCN35 to avoid this race condition. Since the waits happen only at lower interrupt levels the risk of taking too long at higher IRQ and causing a system watchdog timeout are minimal.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix a race between socket set up and I/O thread creation In rxrpc_open_socket(), it sets up the socket and then sets up the I/O thread that will handle it. This is a problem, however, as there's a gap between the two phases in which a packet may come into rxrpc_encap_rcv() from the UDP packet but we oops when trying to wake the not-yet created I/O thread. As a quick fix, just make rxrpc_encap_rcv() discard the packet if there's no I/O thread yet. A better, but more intrusive fix would perhaps be to rearrange things such that the socket creation is done by the I/O thread.

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Ensure DA_ID handling completion before deleting an NPIV instance Deleting an NPIV instance requires all fabric ndlps to be released before an NPIV's resources can be torn down. Failure to release fabric ndlps beforehand opens kref imbalance race conditions. Fix by forcing the DA_ID to complete synchronously with usage of wait_queue.

In the Linux kernel, the following vulnerability has been resolved: media: streamzap: fix race between device disconnection and urb callback Syzkaller has reported a general protection fault at function ir_raw_event_store_with_filter(). This crash is caused by a NULL pointer dereference of dev->raw pointer, even though it is checked for NULL in the same function, which means there is a race condition. It occurs due to the incorrect order of actions in the streamzap_disconnect() function: rc_unregister_device() is called before usb_kill_urb(). The dev->raw pointer is freed and set to NULL in rc_unregister_device(), and only after that usb_kill_urb() waits for in-progress requests to finish. If rc_unregister_device() is called while streamzap_callback() handler is not finished, this can lead to accessing freed resources. Thus rc_unregister_device() should be called after usb_kill_urb(). Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: nvme-pci: fix race condition between reset and nvme_dev_disable() nvme_dev_disable() modifies the dev->online_queues field, therefore nvme_pci_update_nr_queues() should avoid racing against it, otherwise we could end up passing invalid values to blk_mq_update_nr_hw_queues(). WARNING: CPU: 39 PID: 61303 at drivers/pci/msi/api.c:347 pci_irq_get_affinity+0x187/0x210 Workqueue: nvme-reset-wq nvme_reset_work [nvme] RIP: 0010:pci_irq_get_affinity+0x187/0x210 Call Trace: <TASK> ? blk_mq_pci_map_queues+0x87/0x3c0 ? pci_irq_get_affinity+0x187/0x210 blk_mq_pci_map_queues+0x87/0x3c0 nvme_pci_map_queues+0x189/0x460 [nvme] blk_mq_update_nr_hw_queues+0x2a/0x40 nvme_reset_work+0x1be/0x2a0 [nvme] Fix the bug by locking the shutdown_lock mutex before using dev->online_queues. Give up if nvme_dev_disable() is running or if it has been executed already.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to check atomic_file in f2fs ioctl interfaces Some f2fs ioctl interfaces like f2fs_ioc_set_pin_file(), f2fs_move_file_range(), and f2fs_defragment_range() missed to check atomic_write status, which may cause potential race issue, fix it.

In the Linux kernel, the following vulnerability has been resolved: tracing/timerlat: Fix a race during cpuhp processing There is another found exception that the "timerlat/1" thread was scheduled on CPU0, and lead to timer corruption finally: ``` ODEBUG: init active (active state 0) object: ffff888237c2e108 object type: hrtimer hint: timerlat_irq+0x0/0x220 WARNING: CPU: 0 PID: 426 at lib/debugobjects.c:518 debug_print_object+0x7d/0xb0 Modules linked in: CPU: 0 UID: 0 PID: 426 Comm: timerlat/1 Not tainted 6.11.0-rc7+ #45 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 RIP: 0010:debug_print_object+0x7d/0xb0 ... Call Trace: <TASK> ? __warn+0x7c/0x110 ? debug_print_object+0x7d/0xb0 ? report_bug+0xf1/0x1d0 ? prb_read_valid+0x17/0x20 ? handle_bug+0x3f/0x70 ? exc_invalid_op+0x13/0x60 ? asm_exc_invalid_op+0x16/0x20 ? debug_print_object+0x7d/0xb0 ? debug_print_object+0x7d/0xb0 ? __pfx_timerlat_irq+0x10/0x10 __debug_object_init+0x110/0x150 hrtimer_init+0x1d/0x60 timerlat_main+0xab/0x2d0 ? __pfx_timerlat_main+0x10/0x10 kthread+0xb7/0xe0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x40 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ``` After tracing the scheduling event, it was discovered that the migration of the "timerlat/1" thread was performed during thread creation. Further analysis confirmed that it is because the CPU online processing for osnoise is implemented through workers, which is asynchronous with the offline processing. When the worker was scheduled to create a thread, the CPU may has already been removed from the cpu_online_mask during the offline process, resulting in the inability to select the right CPU: T1 | T2 [CPUHP_ONLINE] | cpu_device_down() osnoise_hotplug_workfn() | | cpus_write_lock() | takedown_cpu(1) | cpus_write_unlock() [CPUHP_OFFLINE] | cpus_read_lock() | start_kthread(1) | cpus_read_unlock() | To fix this, skip online processing if the CPU is already offline.

In the Linux kernel, the following vulnerability has been resolved: mm/gup: fix memfd_pin_folios alloc race panic If memfd_pin_folios tries to create a hugetlb page, but someone else already did, then folio gets the value -EEXIST here: folio = memfd_alloc_folio(memfd, start_idx); if (IS_ERR(folio)) { ret = PTR_ERR(folio); if (ret != -EEXIST) goto err; then on the next trip through the "while start_idx" loop we panic here: if (folio) { folio_put(folio); To fix, set the folio to NULL on error.

In the Linux kernel, the following vulnerability has been resolved: lib/generic-radix-tree.c: Fix rare race in __genradix_ptr_alloc() If we need to increase the tree depth, allocate a new node, and then race with another thread that increased the tree depth before us, we'll still have a preallocated node that might be used later. If we then use that node for a new non-root node, it'll still have a pointer to the old root instead of being zeroed - fix this by zeroing it in the cmpxchg failure path.

In the Linux kernel, the following vulnerability has been resolved: ALSA: line6: Fix racy access to midibuf There can be concurrent accesses to line6 midibuf from both the URB completion callback and the rawmidi API access. This could be a cause of KMSAN warning triggered by syzkaller below (so put as reported-by here). This patch protects the midibuf call of the former code path with a spinlock for avoiding the possible races.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_fs: Remove WARN_ON in functionfs_bind This commit addresses an issue related to below kernel panic where panic_on_warn is enabled. It is caused by the unnecessary use of WARN_ON in functionsfs_bind, which easily leads to the following scenarios. 1.adb_write in adbd 2. UDC write via configfs ================= ===================== ->usb_ffs_open_thread() ->UDC write ->open_functionfs() ->configfs_write_iter() ->adb_open() ->gadget_dev_desc_UDC_store() ->adb_write() ->usb_gadget_register_driver_owner ->driver_register() ->StartMonitor() ->bus_add_driver() ->adb_read() ->gadget_bind_driver() <times-out without BIND event> ->configfs_composite_bind() ->usb_add_function() ->open_functionfs() ->ffs_func_bind() ->adb_open() ->functionfs_bind() <ffs->state !=FFS_ACTIVE> The adb_open, adb_read, and adb_write operations are invoked from the daemon, but trying to bind the function is a process that is invoked by UDC write through configfs, which opens up the possibility of a race condition between the two paths. In this race scenario, the kernel panic occurs due to the WARN_ON from functionfs_bind when panic_on_warn is enabled. This commit fixes the kernel panic by removing the unnecessary WARN_ON. Kernel panic - not syncing: kernel: panic_on_warn set ... [ 14.542395] Call trace: [ 14.542464] ffs_func_bind+0x1c8/0x14a8 [ 14.542468] usb_add_function+0xcc/0x1f0 [ 14.542473] configfs_composite_bind+0x468/0x588 [ 14.542478] gadget_bind_driver+0x108/0x27c [ 14.542483] really_probe+0x190/0x374 [ 14.542488] __driver_probe_device+0xa0/0x12c [ 14.542492] driver_probe_device+0x3c/0x220 [ 14.542498] __driver_attach+0x11c/0x1fc [ 14.542502] bus_for_each_dev+0x104/0x160 [ 14.542506] driver_attach+0x24/0x34 [ 14.542510] bus_add_driver+0x154/0x270 [ 14.542514] driver_register+0x68/0x104 [ 14.542518] usb_gadget_register_driver_owner+0x48/0xf4 [ 14.542523] gadget_dev_desc_UDC_store+0xf8/0x144 [ 14.542526] configfs_write_iter+0xf0/0x138

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Check mailbox/SMT channel for consistency On reception of a completion interrupt the shared memory area is accessed to retrieve the message header at first and then, if the message sequence number identifies a transaction which is still pending, the related payload is fetched too. When an SCMI command times out the channel ownership remains with the platform until eventually a late reply is received and, as a consequence, any further transmission attempt remains pending, waiting for the channel to be relinquished by the platform. Once that late reply is received the channel ownership is given back to the agent and any pending request is then allowed to proceed and overwrite the SMT area of the just delivered late reply; then the wait for the reply to the new request starts. It has been observed that the spurious IRQ related to the late reply can be wrongly associated with the freshly enqueued request: when that happens the SCMI stack in-flight lookup procedure is fooled by the fact that the message header now present in the SMT area is related to the new pending transaction, even though the real reply has still to arrive. This race-condition on the A2P channel can be detected by looking at the channel status bits: a genuine reply from the platform will have set the channel free bit before triggering the completion IRQ. Add a consistency check to validate such condition in the A2P ISR.

In the Linux kernel, the following vulnerability has been resolved: perf/core: Fix data race between perf_event_set_output() and perf_mmap_close() Yang Jihing reported a race between perf_event_set_output() and perf_mmap_close(): CPU1 CPU2 perf_mmap_close(e2) if (atomic_dec_and_test(&e2->rb->mmap_count)) // 1 - > 0 detach_rest = true ioctl(e1, IOC_SET_OUTPUT, e2) perf_event_set_output(e1, e2) ... list_for_each_entry_rcu(e, &e2->rb->event_list, rb_entry) ring_buffer_attach(e, NULL); // e1 isn't yet added and // therefore not detached ring_buffer_attach(e1, e2->rb) list_add_rcu(&e1->rb_entry, &e2->rb->event_list) After this; e1 is attached to an unmapped rb and a subsequent perf_mmap() will loop forever more: again: mutex_lock(&e->mmap_mutex); if (event->rb) { ... if (!atomic_inc_not_zero(&e->rb->mmap_count)) { ... mutex_unlock(&e->mmap_mutex); goto again; } } The loop in perf_mmap_close() holds e2->mmap_mutex, while the attach in perf_event_set_output() holds e1->mmap_mutex. As such there is no serialization to avoid this race. Change perf_event_set_output() to take both e1->mmap_mutex and e2->mmap_mutex to alleviate that problem. Additionally, have the loop in perf_mmap() detach the rb directly, this avoids having to wait for the concurrent perf_mmap_close() to get around to doing it to make progress.

In the Linux kernel, the following vulnerability has been resolved: drm/v3d: Assign job pointer to NULL before signaling the fence In commit e4b5ccd392b9 ("drm/v3d: Ensure job pointer is set to NULL after job completion"), we introduced a change to assign the job pointer to NULL after completing a job, indicating job completion. However, this approach created a race condition between the DRM scheduler workqueue and the IRQ execution thread. As soon as the fence is signaled in the IRQ execution thread, a new job starts to be executed. This results in a race condition where the IRQ execution thread sets the job pointer to NULL simultaneously as the `run_job()` function assigns a new job to the pointer. This race condition can lead to a NULL pointer dereference if the IRQ execution thread sets the job pointer to NULL after `run_job()` assigns it to the new job. When the new job completes and the GPU emits an interrupt, `v3d_irq()` is triggered, potentially causing a crash. [ 466.310099] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000c0 [ 466.318928] Mem abort info: [ 466.321723] ESR = 0x0000000096000005 [ 466.325479] EC = 0x25: DABT (current EL), IL = 32 bits [ 466.330807] SET = 0, FnV = 0 [ 466.333864] EA = 0, S1PTW = 0 [ 466.337010] FSC = 0x05: level 1 translation fault [ 466.341900] Data abort info: [ 466.344783] ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000 [ 466.350285] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 466.355350] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 466.360677] user pgtable: 4k pages, 39-bit VAs, pgdp=0000000089772000 [ 466.367140] [00000000000000c0] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000 [ 466.375875] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP [ 466.382163] Modules linked in: rfcomm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device algif_hash algif_skcipher af_alg bnep binfmt_misc vc4 snd_soc_hdmi_codec drm_display_helper cec brcmfmac_wcc spidev rpivid_hevc(C) drm_client_lib brcmfmac hci_uart drm_dma_helper pisp_be btbcm brcmutil snd_soc_core aes_ce_blk v4l2_mem2mem bluetooth aes_ce_cipher snd_compress videobuf2_dma_contig ghash_ce cfg80211 gf128mul snd_pcm_dmaengine videobuf2_memops ecdh_generic sha2_ce ecc videobuf2_v4l2 snd_pcm v3d sha256_arm64 rfkill videodev snd_timer sha1_ce libaes gpu_sched snd videobuf2_common sha1_generic drm_shmem_helper mc rp1_pio drm_kms_helper raspberrypi_hwmon spi_bcm2835 gpio_keys i2c_brcmstb rp1 raspberrypi_gpiomem rp1_mailbox rp1_adc nvmem_rmem uio_pdrv_genirq uio i2c_dev drm ledtrig_pattern drm_panel_orientation_quirks backlight fuse dm_mod ip_tables x_tables ipv6 [ 466.458429] CPU: 0 UID: 1000 PID: 2008 Comm: chromium Tainted: G C 6.13.0-v8+ #18 [ 466.467336] Tainted: [C]=CRAP [ 466.470306] Hardware name: Raspberry Pi 5 Model B Rev 1.0 (DT) [ 466.476157] pstate: 404000c9 (nZcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 466.483143] pc : v3d_irq+0x118/0x2e0 [v3d] [ 466.487258] lr : __handle_irq_event_percpu+0x60/0x228 [ 466.492327] sp : ffffffc080003ea0 [ 466.495646] x29: ffffffc080003ea0 x28: ffffff80c0c94200 x27: 0000000000000000 [ 466.502807] x26: ffffffd08dd81d7b x25: ffffff80c0c94200 x24: ffffff8003bdc200 [ 466.509969] x23: 0000000000000001 x22: 00000000000000a7 x21: 0000000000000000 [ 466.517130] x20: ffffff8041bb0000 x19: 0000000000000001 x18: 0000000000000000 [ 466.524291] x17: ffffffafadfb0000 x16: ffffffc080000000 x15: 0000000000000000 [ 466.531452] x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 [ 466.538613] x11: 0000000000000000 x10: 0000000000000000 x9 : ffffffd08c527eb0 [ 466.545777] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 [ 466.552941] x5 : ffffffd08c4100d0 x4 : ffffffafadfb0000 x3 : ffffffc080003f70 [ 466.560102] x2 : ffffffc0829e8058 x1 : 0000000000000001 x0 : 0000000000000000 [ 466.567263] Call trace: [ 466.569711] v3d_irq+0x118/0x2e0 [v3d] (P) [ 466. ---truncated---

A use-after-free flaw was found in the Linux kernel's Memory Management subsystem when a user wins two races at the same time with a fail in the mas_prev_slot function. This issue could allow a local user to crash the system.

The inode double locking code in fs/ocfs2/file.c in the Linux kernel 2.6.30 before 2.6.30-rc3, 2.6.27 before 2.6.27.24, 2.6.29 before 2.6.29.4, and possibly other versions down to 2.6.19 allows local users to cause a denial of service (prevention of file creation and removal) via a series of splice system calls that trigger a deadlock between the generic_file_splice_write, splice_from_pipe, and ocfs2_file_splice_write functions.

Arm guests can cause Dom0 DoS via PV devices When mapping pages of guests on Arm, dom0 is using an rbtree to keep track of the foreign mappings. Updating of that rbtree is not always done completely with the related lock held, resulting in a small race window, which can be used by unprivileged guests via PV devices to cause inconsistencies of the rbtree. These inconsistencies can lead to Denial of Service (DoS) of dom0, e.g. by causing crashes or the inability to perform further mappings of other guests' memory pages.

A null pointer dereference flaw was found in the Linux kernel API for the cryptographic algorithm scatterwalk functionality. This issue occurs when a user constructs a malicious packet with specific socket configuration, which could allow a local user to crash the system or escalate their privileges on the system.

In the Linux kernel, the following vulnerability has been resolved: xhci: Fix null pointer dereference when host dies Make sure xhci_free_dev() and xhci_kill_endpoint_urbs() do not race and cause null pointer dereference when host suddenly dies. Usb core may call xhci_free_dev() which frees the xhci->devs[slot_id] virt device at the same time that xhci_kill_endpoint_urbs() tries to loop through all the device's endpoints, checking if there are any cancelled urbs left to give back. hold the xhci spinlock while freeing the virt device

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix race between quota rescan and disable leading to NULL pointer deref If we have one task trying to start the quota rescan worker while another one is trying to disable quotas, we can end up hitting a race that results in the quota rescan worker doing a NULL pointer dereference. The steps for this are the following: 1) Quotas are enabled; 2) Task A calls the quota rescan ioctl and enters btrfs_qgroup_rescan(). It calls qgroup_rescan_init() which returns 0 (success) and then joins a transaction and commits it; 3) Task B calls the quota disable ioctl and enters btrfs_quota_disable(). It clears the bit BTRFS_FS_QUOTA_ENABLED from fs_info->flags and calls btrfs_qgroup_wait_for_completion(), which returns immediately since the rescan worker is not yet running. Then it starts a transaction and locks fs_info->qgroup_ioctl_lock; 4) Task A queues the rescan worker, by calling btrfs_queue_work(); 5) The rescan worker starts, and calls rescan_should_stop() at the start of its while loop, which results in 0 iterations of the loop, since the flag BTRFS_FS_QUOTA_ENABLED was cleared from fs_info->flags by task B at step 3); 6) Task B sets fs_info->quota_root to NULL; 7) The rescan worker tries to start a transaction and uses fs_info->quota_root as the root argument for btrfs_start_transaction(). This results in a NULL pointer dereference down the call chain of btrfs_start_transaction(). The stack trace is something like the one reported in Link tag below: general protection fault, probably for non-canonical address 0xdffffc0000000041: 0000 [#1] PREEMPT SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000208-0x000000000000020f] CPU: 1 PID: 34 Comm: kworker/u4:2 Not tainted 6.1.0-syzkaller-13872-gb6bb9676f216 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022 Workqueue: btrfs-qgroup-rescan btrfs_work_helper RIP: 0010:start_transaction+0x48/0x10f0 fs/btrfs/transaction.c:564 Code: 48 89 fb 48 (...) RSP: 0018:ffffc90000ab7ab0 EFLAGS: 00010206 RAX: 0000000000000041 RBX: 0000000000000208 RCX: ffff88801779ba80 RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000 RBP: dffffc0000000000 R08: 0000000000000001 R09: fffff52000156f5d R10: fffff52000156f5d R11: 1ffff92000156f5c R12: 0000000000000000 R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000003 FS: 0000000000000000(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2bea75b718 CR3: 000000001d0cc000 CR4: 00000000003506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> btrfs_qgroup_rescan_worker+0x3bb/0x6a0 fs/btrfs/qgroup.c:3402 btrfs_work_helper+0x312/0x850 fs/btrfs/async-thread.c:280 process_one_work+0x877/0xdb0 kernel/workqueue.c:2289 worker_thread+0xb14/0x1330 kernel/workqueue.c:2436 kthread+0x266/0x300 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308 </TASK> Modules linked in: So fix this by having the rescan worker function not attempt to start a transaction if it didn't do any rescan work.

In the Linux kernel, the following vulnerability has been resolved: phy: lynx-28g: serialize concurrent phy_set_mode_ext() calls to shared registers The protocol converter configuration registers PCC8, PCCC, PCCD (implemented by the driver), as well as others, control protocol converters from multiple lanes (each represented as a different struct phy). So, if there are simultaneous calls to phy_set_mode_ext() to lanes sharing the same PCC register (either for the "old" or for the "new" protocol), corruption of the values programmed to hardware is possible, because lynx_28g_rmw() has no locking. Add a spinlock in the struct lynx_28g_priv shared by all lanes, and take the global spinlock from the phy_ops :: set_mode() implementation. There are no other callers which modify PCC registers.

In the Linux kernel, the following vulnerability has been resolved: x86/sgx: Resolves SECS reclaim vs. page fault for EAUG race The SGX EPC reclaimer (ksgxd) may reclaim the SECS EPC page for an enclave and set secs.epc_page to NULL. The SECS page is used for EAUG and ELDU in the SGX page fault handler. However, the NULL check for secs.epc_page is only done for ELDU, not EAUG before being used. Fix this by doing the same NULL check and reloading of the SECS page as needed for both EAUG and ELDU. The SECS page holds global enclave metadata. It can only be reclaimed when there are no other enclave pages remaining. At that point, virtually nothing can be done with the enclave until the SECS page is paged back in. An enclave can not run nor generate page faults without a resident SECS page. But it is still possible for a #PF for a non-SECS page to race with paging out the SECS page: when the last resident non-SECS page A triggers a #PF in a non-resident page B, and then page A and the SECS both are paged out before the #PF on B is handled. Hitting this bug requires that race triggered with a #PF for EAUG. Following is a trace when it happens. BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:sgx_encl_eaug_page+0xc7/0x210 Call Trace: ? __kmem_cache_alloc_node+0x16a/0x440 ? xa_load+0x6e/0xa0 sgx_vma_fault+0x119/0x230 __do_fault+0x36/0x140 do_fault+0x12f/0x400 __handle_mm_fault+0x728/0x1110 handle_mm_fault+0x105/0x310 do_user_addr_fault+0x1ee/0x750 ? __this_cpu_preempt_check+0x13/0x20 exc_page_fault+0x76/0x180 asm_exc_page_fault+0x27/0x30

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix handling of cached open files in nfsd4_open codepath Commit fb70bf124b05 ("NFSD: Instantiate a struct file when creating a regular NFSv4 file") added the ability to cache an open fd over a compound. There are a couple of problems with the way this currently works: It's racy, as a newly-created nfsd_file can end up with its PENDING bit cleared while the nf is hashed, and the nf_file pointer is still zeroed out. Other tasks can find it in this state and they expect to see a valid nf_file, and can oops if nf_file is NULL. Also, there is no guarantee that we'll end up creating a new nfsd_file if one is already in the hash. If an extant entry is in the hash with a valid nf_file, nfs4_get_vfs_file will clobber its nf_file pointer with the value of op_file and the old nf_file will leak. Fix both issues by making a new nfsd_file_acquirei_opened variant that takes an optional file pointer. If one is present when this is called, we'll take a new reference to it instead of trying to open the file. If the nfsd_file already has a valid nf_file, we'll just ignore the optional file and pass the nfsd_file back as-is. Also rework the tracepoints a bit to allow for an "opened" variant and don't try to avoid counting acquisitions in the case where we already have a cached open file.

An issue was discovered in the Linux kernel through 6.5.9. During a race with SQ thread exit, an io_uring/fdinfo.c io_uring_show_fdinfo NULL pointer dereference can occur.

In the Linux kernel, the following vulnerability has been resolved: i2c: sprd: fix reference leak when pm_runtime_get_sync fails The PM reference count is not expected to be incremented on return in sprd_i2c_master_xfer() and sprd_i2c_remove(). However, pm_runtime_get_sync will increment the PM reference count even failed. Forgetting to putting operation will result in a reference leak here. Replace it with pm_runtime_resume_and_get to keep usage counter balanced.

A NULL pointer dereference flaw was found in the Linux kernel’s Amateur Radio AX.25 protocol functionality in the way a user connects with the protocol. This flaw allows a local user to crash the system.

In the Linux kernel, the following vulnerability has been resolved: netfilter: conntrack: serialize hash resizes and cleanups Syzbot was able to trigger the following warning [1] No repro found by syzbot yet but I was able to trigger similar issue by having 2 scripts running in parallel, changing conntrack hash sizes, and: for j in `seq 1 1000` ; do unshare -n /bin/true >/dev/null ; done It would take more than 5 minutes for net_namespace structures to be cleaned up. This is because nf_ct_iterate_cleanup() has to restart everytime a resize happened. By adding a mutex, we can serialize hash resizes and cleanups and also make get_next_corpse() faster by skipping over empty buckets. Even without resizes in the picture, this patch considerably speeds up network namespace dismantles. [1] INFO: task syz-executor.0:8312 can't die for more than 144 seconds. task:syz-executor.0 state:R running task stack:25672 pid: 8312 ppid: 6573 flags:0x00004006 Call Trace: context_switch kernel/sched/core.c:4955 [inline] __schedule+0x940/0x26f0 kernel/sched/core.c:6236 preempt_schedule_common+0x45/0xc0 kernel/sched/core.c:6408 preempt_schedule_thunk+0x16/0x18 arch/x86/entry/thunk_64.S:35 __local_bh_enable_ip+0x109/0x120 kernel/softirq.c:390 local_bh_enable include/linux/bottom_half.h:32 [inline] get_next_corpse net/netfilter/nf_conntrack_core.c:2252 [inline] nf_ct_iterate_cleanup+0x15a/0x450 net/netfilter/nf_conntrack_core.c:2275 nf_conntrack_cleanup_net_list+0x14c/0x4f0 net/netfilter/nf_conntrack_core.c:2469 ops_exit_list+0x10d/0x160 net/core/net_namespace.c:171 setup_net+0x639/0xa30 net/core/net_namespace.c:349 copy_net_ns+0x319/0x760 net/core/net_namespace.c:470 create_new_namespaces+0x3f6/0xb20 kernel/nsproxy.c:110 unshare_nsproxy_namespaces+0xc1/0x1f0 kernel/nsproxy.c:226 ksys_unshare+0x445/0x920 kernel/fork.c:3128 __do_sys_unshare kernel/fork.c:3202 [inline] __se_sys_unshare kernel/fork.c:3200 [inline] __x64_sys_unshare+0x2d/0x40 kernel/fork.c:3200 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f63da68e739 RSP: 002b:00007f63d7c05188 EFLAGS: 00000246 ORIG_RAX: 0000000000000110 RAX: ffffffffffffffda RBX: 00007f63da792f80 RCX: 00007f63da68e739 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000040000000 RBP: 00007f63da6e8cc4 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f63da792f80 R13: 00007fff50b75d3f R14: 00007f63d7c05300 R15: 0000000000022000 Showing all locks held in the system: 1 lock held by khungtaskd/27: #0: ffffffff8b980020 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x53/0x260 kernel/locking/lockdep.c:6446 2 locks held by kworker/u4:2/153: #0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic64_set arch/x86/include/asm/atomic64_64.h:34 [inline] #0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: arch_atomic_long_set include/linux/atomic/atomic-long.h:41 [inline] #0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: atomic_long_set include/linux/atomic/atomic-instrumented.h:1198 [inline] #0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_data kernel/workqueue.c:634 [inline] #0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: set_work_pool_and_clear_pending kernel/workqueue.c:661 [inline] #0: ffff888010c69138 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x896/0x1690 kernel/workqueue.c:2268 #1: ffffc9000140fdb0 ((kfence_timer).work){+.+.}-{0:0}, at: process_one_work+0x8ca/0x1690 kernel/workqueue.c:2272 1 lock held by systemd-udevd/2970: 1 lock held by in:imklog/6258: #0: ffff88807f970ff0 (&f->f_pos_lock){+.+.}-{3:3}, at: __fdget_pos+0xe9/0x100 fs/file.c:990 3 locks held by kworker/1:6/8158: 1 lock held by syz-executor.0/8312: 2 locks held by kworker/u4:13/9320: 1 lock held by ---truncated---

In the Linux kernel, the following vulnerability has been resolved: xprtrdma: Fix cwnd update ordering After a reconnect, the reply handler is opening the cwnd (and thus enabling more RPC Calls to be sent) /before/ rpcrdma_post_recvs() can post enough Receive WRs to receive their replies. This causes an RNR and the new connection is lost immediately. The race is most clearly exposed when KASAN and disconnect injection are enabled. This slows down rpcrdma_rep_create() enough to allow the send side to post a bunch of RPC Calls before the Receive completion handler can invoke ib_post_recv().

In the Linux kernel, the following vulnerability has been resolved: isdn: mISDN: netjet: Fix crash in nj_probe: 'nj_setup' in netjet.c might fail with -EIO and in this case 'card->irq' is initialized and is bigger than zero. A subsequent call to 'nj_release' will free the irq that has not been requested. Fix this bug by deleting the previous assignment to 'card->irq' and just keep the assignment before 'request_irq'. The KASAN's log reveals it: [ 3.354615 ] WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1826 free_irq+0x100/0x480 [ 3.355112 ] Modules linked in: [ 3.355310 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e #13 [ 3.355816 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.356552 ] RIP: 0010:free_irq+0x100/0x480 [ 3.356820 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18 4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5 ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80 [ 3.358012 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082 [ 3.358357 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX: 0000000000000000 [ 3.358814 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI: 00000000ffffffff [ 3.359272 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09: 0000000000000000 [ 3.359732 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12: 0000000000000000 [ 3.360195 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15: ffff888104dc80a8 [ 3.360652 ] FS: 0000000000000000(0000) GS:ffff88817bc00000(0000) knlGS:0000000000000000 [ 3.361170 ] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3.361538 ] CR2: 0000000000000000 CR3: 000000000582e000 CR4: 00000000000006f0 [ 3.362003 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3.362175 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 3.362175 ] Call Trace: [ 3.362175 ] nj_release+0x51/0x1e0 [ 3.362175 ] nj_probe+0x450/0x950 [ 3.362175 ] ? pci_device_remove+0x110/0x110 [ 3.362175 ] local_pci_probe+0x45/0xa0 [ 3.362175 ] pci_device_probe+0x12b/0x1d0 [ 3.362175 ] really_probe+0x2a9/0x610 [ 3.362175 ] driver_probe_device+0x90/0x1d0 [ 3.362175 ] ? mutex_lock_nested+0x1b/0x20 [ 3.362175 ] device_driver_attach+0x68/0x70 [ 3.362175 ] __driver_attach+0x124/0x1b0 [ 3.362175 ] ? device_driver_attach+0x70/0x70 [ 3.362175 ] bus_for_each_dev+0xbb/0x110 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] driver_attach+0x27/0x30 [ 3.362175 ] bus_add_driver+0x1eb/0x2a0 [ 3.362175 ] driver_register+0xa9/0x180 [ 3.362175 ] __pci_register_driver+0x82/0x90 [ 3.362175 ] ? w6692_init+0x38/0x38 [ 3.362175 ] nj_init+0x36/0x38 [ 3.362175 ] do_one_initcall+0x7f/0x3d0 [ 3.362175 ] ? rdinit_setup+0x45/0x45 [ 3.362175 ] ? rcu_read_lock_sched_held+0x4f/0x80 [ 3.362175 ] kernel_init_freeable+0x2aa/0x301 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] kernel_init+0x18/0x190 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ? rest_init+0x2c0/0x2c0 [ 3.362175 ] ret_from_fork+0x1f/0x30 [ 3.362175 ] Kernel panic - not syncing: panic_on_warn set ... [ 3.362175 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc1-00144-g25a1298726e #13 [ 3.362175 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014 [ 3.362175 ] Call Trace: [ 3.362175 ] dump_stack+0xba/0xf5 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] panic+0x15a/0x3f2 [ 3.362175 ] ? __warn+0xf2/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] __warn+0x108/0x150 [ 3.362175 ] ? free_irq+0x100/0x480 [ 3.362175 ] report_bug+0x119/0x1c0 [ 3.362175 ] handle_bug+0x3b/0x80 [ 3.362175 ] exc_invalid_op+0x18/0x70 [ 3.362175 ] asm_exc_invalid_op+0x12/0x20 [ 3.362175 ] RIP: 0010:free_irq+0x100 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix race between transaction aborts and fsyncs leading to use-after-free There is a race between a task aborting a transaction during a commit, a task doing an fsync and the transaction kthread, which leads to an use-after-free of the log root tree. When this happens, it results in a stack trace like the following: BTRFS info (device dm-0): forced readonly BTRFS warning (device dm-0): Skipping commit of aborted transaction. BTRFS: error (device dm-0) in cleanup_transaction:1958: errno=-5 IO failure BTRFS warning (device dm-0): lost page write due to IO error on /dev/mapper/error-test (-5) BTRFS warning (device dm-0): Skipping commit of aborted transaction. BTRFS warning (device dm-0): direct IO failed ino 261 rw 0,0 sector 0xa4e8 len 4096 err no 10 BTRFS error (device dm-0): error writing primary super block to device 1 BTRFS warning (device dm-0): direct IO failed ino 261 rw 0,0 sector 0x12e000 len 4096 err no 10 BTRFS warning (device dm-0): direct IO failed ino 261 rw 0,0 sector 0x12e008 len 4096 err no 10 BTRFS warning (device dm-0): direct IO failed ino 261 rw 0,0 sector 0x12e010 len 4096 err no 10 BTRFS: error (device dm-0) in write_all_supers:4110: errno=-5 IO failure (1 errors while writing supers) BTRFS: error (device dm-0) in btrfs_sync_log:3308: errno=-5 IO failure general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b68: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC PTI CPU: 2 PID: 2458471 Comm: fsstress Not tainted 5.12.0-rc5-btrfs-next-84 #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 RIP: 0010:__mutex_lock+0x139/0xa40 Code: c0 74 19 (...) RSP: 0018:ffff9f18830d7b00 EFLAGS: 00010202 RAX: 6b6b6b6b6b6b6b68 RBX: 0000000000000001 RCX: 0000000000000002 RDX: ffffffffb9c54d13 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff9f18830d7bc0 R08: 0000000000000000 R09: 0000000000000000 R10: ffff9f18830d7be0 R11: 0000000000000001 R12: ffff8c6cd199c040 R13: ffff8c6c95821358 R14: 00000000fffffffb R15: ffff8c6cbcf01358 FS: 00007fa9140c2b80(0000) GS:ffff8c6fac600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fa913d52000 CR3: 000000013d2b4003 CR4: 0000000000370ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: ? __btrfs_handle_fs_error+0xde/0x146 [btrfs] ? btrfs_sync_log+0x7c1/0xf20 [btrfs] ? btrfs_sync_log+0x7c1/0xf20 [btrfs] btrfs_sync_log+0x7c1/0xf20 [btrfs] btrfs_sync_file+0x40c/0x580 [btrfs] do_fsync+0x38/0x70 __x64_sys_fsync+0x10/0x20 do_syscall_64+0x33/0x80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7fa9142a55c3 Code: 8b 15 09 (...) RSP: 002b:00007fff26278d48 EFLAGS: 00000246 ORIG_RAX: 000000000000004a RAX: ffffffffffffffda RBX: 0000563c83cb4560 RCX: 00007fa9142a55c3 RDX: 00007fff26278cb0 RSI: 00007fff26278cb0 RDI: 0000000000000005 RBP: 0000000000000005 R08: 0000000000000001 R09: 00007fff26278d5c R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000340 R13: 00007fff26278de0 R14: 00007fff26278d96 R15: 0000563c83ca57c0 Modules linked in: btrfs dm_zero dm_snapshot dm_thin_pool (...) ---[ end trace ee2f1b19327d791d ]--- The steps that lead to this crash are the following: 1) We are at transaction N; 2) We have two tasks with a transaction handle attached to transaction N. Task A and Task B. Task B is doing an fsync; 3) Task B is at btrfs_sync_log(), and has saved fs_info->log_root_tree into a local variable named 'log_root_tree' at the top of btrfs_sync_log(). Task B is about to call write_all_supers(), but before that... 4) Task A calls btrfs_commit_transaction(), and after it sets the transaction state to TRANS_STATE_COMMIT_START, an error happens before it w ---truncated---

In the Linux kernel, the following vulnerability has been resolved: dm: fix mempool NULL pointer race when completing IO dm_io_dec_pending() calls end_io_acct() first and will then dec md in-flight pending count. But if a task is swapping DM table at same time this can result in a crash due to mempool->elements being NULL: task1 task2 do_resume ->do_suspend ->dm_wait_for_completion bio_endio ->clone_endio ->dm_io_dec_pending ->end_io_acct ->wakeup task1 ->dm_swap_table ->__bind ->__bind_mempools ->bioset_exit ->mempool_exit ->free_io [ 67.330330] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 ...... [ 67.330494] pstate: 80400085 (Nzcv daIf +PAN -UAO) [ 67.330510] pc : mempool_free+0x70/0xa0 [ 67.330515] lr : mempool_free+0x4c/0xa0 [ 67.330520] sp : ffffff8008013b20 [ 67.330524] x29: ffffff8008013b20 x28: 0000000000000004 [ 67.330530] x27: ffffffa8c2ff40a0 x26: 00000000ffff1cc8 [ 67.330535] x25: 0000000000000000 x24: ffffffdada34c800 [ 67.330541] x23: 0000000000000000 x22: ffffffdada34c800 [ 67.330547] x21: 00000000ffff1cc8 x20: ffffffd9a1304d80 [ 67.330552] x19: ffffffdada34c970 x18: 000000b312625d9c [ 67.330558] x17: 00000000002dcfbf x16: 00000000000006dd [ 67.330563] x15: 000000000093b41e x14: 0000000000000010 [ 67.330569] x13: 0000000000007f7a x12: 0000000034155555 [ 67.330574] x11: 0000000000000001 x10: 0000000000000001 [ 67.330579] x9 : 0000000000000000 x8 : 0000000000000000 [ 67.330585] x7 : 0000000000000000 x6 : ffffff80148b5c1a [ 67.330590] x5 : ffffff8008013ae0 x4 : 0000000000000001 [ 67.330596] x3 : ffffff80080139c8 x2 : ffffff801083bab8 [ 67.330601] x1 : 0000000000000000 x0 : ffffffdada34c970 [ 67.330609] Call trace: [ 67.330616] mempool_free+0x70/0xa0 [ 67.330627] bio_put+0xf8/0x110 [ 67.330638] dec_pending+0x13c/0x230 [ 67.330644] clone_endio+0x90/0x180 [ 67.330649] bio_endio+0x198/0x1b8 [ 67.330655] dec_pending+0x190/0x230 [ 67.330660] clone_endio+0x90/0x180 [ 67.330665] bio_endio+0x198/0x1b8 [ 67.330673] blk_update_request+0x214/0x428 [ 67.330683] scsi_end_request+0x2c/0x300 [ 67.330688] scsi_io_completion+0xa0/0x710 [ 67.330695] scsi_finish_command+0xd8/0x110 [ 67.330700] scsi_softirq_done+0x114/0x148 [ 67.330708] blk_done_softirq+0x74/0xd0 [ 67.330716] __do_softirq+0x18c/0x374 [ 67.330724] irq_exit+0xb4/0xb8 [ 67.330732] __handle_domain_irq+0x84/0xc0 [ 67.330737] gic_handle_irq+0x148/0x1b0 [ 67.330744] el1_irq+0xe8/0x190 [ 67.330753] lpm_cpuidle_enter+0x4f8/0x538 [ 67.330759] cpuidle_enter_state+0x1fc/0x398 [ 67.330764] cpuidle_enter+0x18/0x20 [ 67.330772] do_idle+0x1b4/0x290 [ 67.330778] cpu_startup_entry+0x20/0x28 [ 67.330786] secondary_start_kernel+0x160/0x170 Fix this by: 1) Establishing pointers to 'struct dm_io' members in dm_io_dec_pending() so that they may be passed into end_io_acct() _after_ free_io() is called. 2) Moving end_io_acct() after free_io().

In the Linux kernel, the following vulnerability has been resolved: btrfs: qgroup: do not warn on record without old_roots populated [BUG] There are some reports from the mailing list that since v6.1 kernel, the WARN_ON() inside btrfs_qgroup_account_extent() gets triggered during rescan: WARNING: CPU: 3 PID: 6424 at fs/btrfs/qgroup.c:2756 btrfs_qgroup_account_extents+0x1ae/0x260 [btrfs] CPU: 3 PID: 6424 Comm: snapperd Tainted: P OE 6.1.2-1-default #1 openSUSE Tumbleweed 05c7a1b1b61d5627475528f71f50444637b5aad7 RIP: 0010:btrfs_qgroup_account_extents+0x1ae/0x260 [btrfs] Call Trace: <TASK> btrfs_commit_transaction+0x30c/0xb40 [btrfs c39c9c546c241c593f03bd6d5f39ea1b676250f6] ? start_transaction+0xc3/0x5b0 [btrfs c39c9c546c241c593f03bd6d5f39ea1b676250f6] btrfs_qgroup_rescan+0x42/0xc0 [btrfs c39c9c546c241c593f03bd6d5f39ea1b676250f6] btrfs_ioctl+0x1ab9/0x25c0 [btrfs c39c9c546c241c593f03bd6d5f39ea1b676250f6] ? __rseq_handle_notify_resume+0xa9/0x4a0 ? mntput_no_expire+0x4a/0x240 ? __seccomp_filter+0x319/0x4d0 __x64_sys_ioctl+0x90/0xd0 do_syscall_64+0x5b/0x80 ? syscall_exit_to_user_mode+0x17/0x40 ? do_syscall_64+0x67/0x80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7fd9b790d9bf </TASK> [CAUSE] Since commit e15e9f43c7ca ("btrfs: introduce BTRFS_QGROUP_RUNTIME_FLAG_NO_ACCOUNTING to skip qgroup accounting"), if our qgroup is already in inconsistent state, we will no longer do the time-consuming backref walk. This can leave some qgroup records without a valid old_roots ulist. Normally this is fine, as btrfs_qgroup_account_extents() would also skip those records if we have NO_ACCOUNTING flag set. But there is a small window, if we have NO_ACCOUNTING flag set, and inserted some qgroup_record without a old_roots ulist, but then the user triggered a qgroup rescan. During btrfs_qgroup_rescan(), we firstly clear NO_ACCOUNTING flag, then commit current transaction. And since we have a qgroup_record with old_roots = NULL, we trigger the WARN_ON() during btrfs_qgroup_account_extents(). [FIX] Unfortunately due to the introduction of NO_ACCOUNTING flag, the assumption that every qgroup_record would have its old_roots populated is no longer correct. Fix the false alerts and drop the WARN_ON().

In the Linux kernel, the following vulnerability has been resolved: HID: logitech-hidpp: Fix kernel crash on receiver USB disconnect hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU) races when it races with itself. hidpp_connect_event() primarily runs from a workqueue but it also runs on probe() and if a "device-connected" packet is received by the hw when the thread running hidpp_connect_event() from probe() is waiting on the hw, then a second thread running hidpp_connect_event() will be started from the workqueue. This opens the following races (note the below code is simplified): 1. Retrieving + printing the protocol (harmless race): if (!hidpp->protocol_major) { hidpp_root_get_protocol_version() hidpp->protocol_major = response.rap.params[0]; } We can actually see this race hit in the dmesg in the abrt output attached to rhbz#2227968: [ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected. [ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected. Testing with extra logging added has shown that after this the 2 threads take turn grabbing the hw access mutex (send_mutex) so they ping-pong through all the other TOCTOU cases managing to hit all of them: 2. Updating the name to the HIDPP name (harmless race): if (hidpp->name == hdev->name) { ... hidpp->name = new_name; } 3. Initializing the power_supply class for the battery (problematic!): hidpp_initialize_battery() { if (hidpp->battery.ps) return 0; probe_battery(); /* Blocks, threads take turns executing this */ hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); } 4. Creating delayed input_device (potentially problematic): if (hidpp->delayed_input) return; hidpp->delayed_input = hidpp_allocate_input(hdev); The really big problem here is 3. Hitting the race leads to the following sequence: hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); ... hidpp->battery.desc.properties = devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL); hidpp->battery.ps = devm_power_supply_register(&hidpp->hid_dev->dev, &hidpp->battery.desc, cfg); So now we have registered 2 power supplies for the same battery, which looks a bit weird from userspace's pov but this is not even the really big problem. Notice how: 1. This is all devm-maganaged 2. The hidpp->battery.desc struct is shared between the 2 power supplies 3. hidpp->battery.desc.properties points to the result from the second devm_kmemdup() This causes a use after free scenario on USB disconnect of the receiver: 1. The last registered power supply class device gets unregistered 2. The memory from the last devm_kmemdup() call gets freed, hidpp->battery.desc.properties now points to freed memory 3. The first registered power supply class device gets unregistered, this involves sending a remove uevent to userspace which invokes power_supply_uevent() to fill the uevent data 4. power_supply_uevent() uses hidpp->battery.desc.properties which now points to freed memory leading to backtraces like this one: Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08 ... Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0 ... Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30 Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0 Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0 Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0 Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680 Sep 22 20:01:35 eric kernel: ---truncated---

A flaw was found in the MCTP protocol in the Linux kernel. The function mctp_unregister() reclaims the device's relevant resource when a netcard detaches. However, a running routine may be unaware of this and cause the use-after-free of the mdev->addrs object, potentially leading to a denial of service.

Anaconda 3 2023.03-1-Linux allows local users to disrupt TLS certificate validation by modifying the cacert.pem file used by the installed pip program. This occurs because many files are installed as world-writable on Linux, ignoring umask, even when these files are installed as root. Miniconda is also affected.

An issue was discovered in the Linux kernel before 6.2.9. A use-after-free was found in bq24190_remove in drivers/power/supply/bq24190_charger.c. It could allow a local attacker to crash the system due to a race condition.