When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of small fragments requiring reassembly, generating the following error messages: [LOG: Err] MQSS(2): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[2:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(2): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1960, QID 0 [LOG: Err] MQSS(2): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0xc38fb1 [LOG: Notice] Error: /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(2), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/0/pfe/0/cm/0/MQSS(2)/2/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(2) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S9, 17.4R3-S1 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D34, 18.2X75-D41, 18.2X75-D53, 18.2X75-D65, 18.2X75-D430 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S2 on MX Series; 18.4 versions prior to 18.4R1-S6, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S4, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.

A vulnerability in Juniper Networks Junos OS Evolved may allow an attacker to cause a Denial of Service (DoS) by sending a high rate of specific packets to the device, resulting in a pfemand process crash. The pfemand process is responsible for packet forwarding on the device. By continuously sending the packet flood, an attacker can repeatedly crash the pfemand process causing a sustained Denial of Service. This issue can only be triggered by traffic sent to the device. Transit traffic does not cause this issue. This issue affects all version of Junos OS Evolved prior to 19.1R1-EVO.

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific BGP packet can lead to a routing process daemon (RPD) crash and restart. This issue can occur even before the BGP session with the peer is established. Repeated receipt of this specific BGP packet can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 18.2X75 versions starting from 18.2X75-D50.8, 18.2X75-D60 and later versions, prior to 18.2X75-D52.8, 18.2X75-D53, 18.2X75-D60.2, 18.2X75-D65.1, 18.2X75-D70; 19.4 versions 19.4R1 and 19.4R1-S1; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved: 19.4-EVO versions prior to 19.4R2-S2-EVO; 20.1-EVO versions prior to 20.1R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

A vulnerability in the processing of inbound IPv6 packets in Juniper Networks Junos OS on QFX5000 Series and EX4600 switches may cause the memory to not be freed, leading to a packet DMA memory leak, and eventual Denial of Service (DoS) condition. Once the condition occurs, further packet processing will be impacted, creating a sustained Denial of Service (DoS) condition. The following error logs may be observed using the "show heap" command and the device may eventually run out of memory if such packets are received continuously. Jan 12 12:00:00 device-name fpc0 (buf alloc) failed allocating packet buffer Jan 12 12:00:01 device-name fpc0 (buf alloc) failed allocating packet buffer user@device-name> request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 246fc1a8 536870488 353653752 183216736 34 Kernel 1 91800000 16777216 12069680 4707536 28 DMA 2 92800000 75497472 69997640 5499832 7 PKT DMA DESC 3 106fc000 335544320 221425960 114118360 34 Bcm_sdk 4 97000000 176160768 200 176160568 99 Packet DMA <<<<<<<<<<<<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects Juniper Networks Junos OS on QFX5000 Series, EX4600: 18.3R3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS: Any versions prior to 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.

On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a prolonged Denial of Service. This issue affects MX Series devices using MS-PIC, MS-MIC or MS-MPC service cards with any service configured. This issue affects Juniper Networks Junos OS on MX Series: 17.2R2-S7; 17.3R3-S4, 17.3R3-S5; 17.4R2-S4 and the subsequent SRs (17.4R2-S5, 17.4R2-S6, etc.); 17.4R3; 18.1R3-S3, 18.1R3-S4, 18.1R3-S5, 18.1R3-S6, 18.1R3-S7, 18.1R3-S8; 18.2R3, 18.2R3-S1, 18.2R3-S2; 18.3R2 and the SRs based on 18.3R2; 18.4R2 and the SRs based on 18.4R2; 19.1R1 and the SRs based on 19.1R1; 19.2R1 and the SRs based on 19.2R1; 19.3R1 and the SRs based on 19.3R1.

On Juniper Networks Junos OS and Junos OS Evolved devices, the receipt of a specific BGP UPDATE packet causes an internal counter to be incremented incorrectly, which over time can lead to the routing protocols process (RPD) crash and restart. This issue affects both IBGP and EBGP multihop deployment in IPv4 or IPv6 network. This issue affects: Juniper Networks Junos OS: 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S4; 18.2X75 versions prior to 18.2X75-D13, 18.2X75-D411.1, 18.2X75-D420.18, 18.2X75-D52.3, 18.2X75-D60; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS Evolved: any releases prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS releases prior to 17.3R1.

The FPC (Flexible PIC Concentrator) of Juniper Networks Junos OS and Junos OS Evolved may restart after processing a specific IPv4 packet. Only packets destined to the device itself, successfully reaching the RE through existing edge and control plane filtering, will be able to cause the FPC restart. When this issue occurs, all traffic via the FPC will be dropped. By continuously sending this specific IPv4 packet, an attacker can repeatedly crash the FPC, causing an extended Denial of Service (DoS) condition. This issue can only occur when processing a specific IPv4 packet. IPv6 packets cannot trigger this issue. This issue affects: Juniper Networks Junos OS on MX Series with MPC10E or MPC11E and PTX10001: 19.2 versions prior to 19.2R1-S4, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S1, 19.4R2. Juniper Networks Junos OS Evolved on on QFX5220, and PTX10003 series: 19.2-EVO versions; 19.3-EVO versions; 19.4-EVO versions prior to 19.4R2-EVO. This issue does not affect Junos OS versions prior to 19.2R1. This issue does not affect Junos OS Evolved versions prior to 19.2R1-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the processing of specific IPv6 packets on certain EX Series devices may lead to exhaustion of DMA memory causing a Denial of Service (DoS). Over time, exploitation of this vulnerability may cause traffic to stop being forwarded, or a crash of the fxpc process. An indication of the issue occurring may be observed through the following log messages: Sep 13 17:14:59 hostname : %PFE-3: fpc0 (buf alloc) failed allocating packet buffer Sep 13 17:14:59 hostname : %PFE-7: fpc0 brcm_pkt_buf_alloc:393 (buf alloc) failed allocating packet buffer When Packet DMA heap utilization reaches 99%, the system will become unstable. Packet DMA heap utilization can be monitored using the command: user@junos# request pfe execute target fpc0 timeout 30 command "show heap" ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 213301a8 536870488 387228840 149641648 27 Kernel 1 91800000 8388608 3735120 4653488 55 DMA 2 92000000 75497472 74452192 1045280 1 PKT DMA DESC 3 d330000 335544320 257091400 78452920 23 Bcm_sdk 4 96800000 184549376 2408 184546968 99 Packet DMA <<<< 5 903fffe0 20971504 20971504 0 0 Blob This issue affects: Juniper Networks Junos OS 18.4 versions prior to 18.4R2-S10, 18.4R3-S10 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.1 versions prior to 19.1R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.3 versions prior to 19.3R3-S5 on EX2300 Series, EX2300-MP Series, EX3400 Series; 19.4 versions prior to 19.4R3-S7 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.1 versions prior to 20.1R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.2 versions prior to 20.2R3-S3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.3 versions prior to 20.3R3-S2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 20.4 versions prior to 20.4R3-S1 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.1 versions prior to 21.1R2-S2, 21.1R3 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.2 versions prior to 21.2R1-S2, 21.2R2 on EX2300 Series, EX2300-MP Series, EX3400 Series; 21.3 versions prior to 21.3R1-S1, 21.3R2 on EX2300 Series, EX2300-MP Series, EX3400 Series.

A Use After Free vulnerability in the Advanced Forwarding Toolkit (AFT) manager process (aftmand) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause a kernel crash due to intensive polling of Abstracted Fabric (AF) interface statistics and thereby a Denial of Service (DoS). Continued gathering of AF interface statistics will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on MX Series: 20.1 versions later than 20.1R1; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; 21.2 versions prior to 21.2R2.

An Improper Validation of Syntactic Correctness of Input vulnerability in the kernel of Juniper Networks Junos OS Evolved on PTX series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an incoming TCP packet destined to the device is malformed there is a possibility of a kernel panic. Only TCP packets destined to the ports for BGP, LDP and MSDP can trigger this. This issue only affects PTX10004, PTX10008, PTX10016. No other PTX Series devices or other platforms are affected. This issue affects Juniper Networks Junos OS Evolved: 20.4-EVO versions prior to 20.4R3-S4-EVO; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 20.4R1-EVO.

An improper use of a validation framework when processing incoming genuine BGP packets within Juniper Networks RPD (routing protocols process) daemon allows an attacker to crash RPD thereby causing a Denial of Service (DoS) condition. This framework requires these packets to be passed. By continuously sending any of these types of formatted genuine packets, an attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Authentication to the BGP peer is not required. This issue can be initiated or propagated through eBGP and iBGP and can impact devices in either modes of use as long as the devices are configured to support the compromised framework and a BGP path is activated or active. This issue affects: Juniper Networks Junos OS 16.1 versions 16.1R7-S6 and later versions prior to 16.1R7-S8; 17.3 versions 17.3R2-S5, 17.3R3-S6 and later versions prior to 17.3R3-S8; 17.4 versions 17.4R2-S7, 17.4R3 and later versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions 18.1R3-S7 and later versions prior to 18.1R3-S10; 18.2 versions 18.2R2-S6, 18.2R3-S2 and later versions prior to 18.2R2-S7, 18.2R3-S5; 18.2X75 versions 18.2X75-D12, 18.2X75-D32, 18.2X75-D33, 18.2X75-D51, 18.2X75-D60, 18.2X75-D411, 18.2X75-D420 and later versions prior to 18.2X75-D32, 18.2X75-D33, 18.2X75-D420, 18.2X75-D52, 18.2X75-D60, 18.2X75-D65, 18.2X75-D70;(*1) 18.3 versions 18.3R1-S6, 18.3R2-S3, 18.3R3 and later versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions 18.4R1-S5, 18.4R2-S4, 18.4R3 and later versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S3(*2); 19.1 versions 19.1R1-S3, 19.1R2 and later versions prior to 19.1R1-S5, 19.1R2-S2, 19.1R3-S2; 19.2 versions 19.2R1-S2, 19.2R2 and later versions prior to 19.2R1-S5, 19.2R2, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2, 19.4R3; 20.1 versions prior to 20.1R1-S1, 20.1R2. This issue does not affect Junos OS prior to 16.1R1. This issue affects IPv4 and IPv6 traffic.

On Juniper Networks Junos OS devices configured with DHCPv6 relay enabled, receipt of a specific DHCPv6 packet might crash the jdhcpd daemon. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. Only DHCPv6 packet can trigger this issue. DHCPv4 packet cannot trigger this issue. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2.

On High-End SRX Series devices, in specific configurations and when specific networking events or operator actions occur, an SPC receiving genuine multicast traffic may core. Subsequently, all FPCs in a chassis may reset causing a Denial of Service. This issue affects both IPv4 and IPv6. This issue affects: Juniper Networks Junos OS 12.3X48 version 12.3X48-D80 and later versions prior to 12.3X48-D95 on High-End SRX Series. This issue does not affect Branch SRX Series devices.

On SRX Series devices, a vulnerability in the key-management-daemon (kmd) daemon of Juniper Networks Junos OS allows an attacker to spoof packets targeted to IPSec peers before a security association (SA) is established thereby causing a failure to set up the IPSec channel. Sustained receipt of these spoofed packets can cause a sustained Denial of Service (DoS) condition. This issue affects IPv4 and IPv6 implementations. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D190; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S6, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2. This issue does not affect 12.3 or 15.1 releases which are non-SRX Series releases.

An Allocation of Resources Without Limits or Throttling vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved allows unauthenticated network based attacker to cause a Denial of Service (DoS). On all Junos Evolved platforms hostbound protocols will be impacted by a high rate of specific hostbound traffic from ports on a PFE. Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS Evolved: 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.2R1.

A Missing Release of Memory after Effective Lifetime vulnerability in the Public Key Infrastructure daemon (pkid) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause Denial of Service (DoS). In a scenario where Public Key Infrastructure (PKI) is used in combination with Certificate Revocation List (CRL), if the CRL fails to download the memory allocated to store the CRL is not released. Repeated occurrences will eventually consume all available memory and lead to an inoperable state of the affected system causing a DoS. This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue can be observed by monitoring the memory utilization of the pkid process via: root@jtac-srx1500-r2003> show system processes extensive | match pki 20931 root 20 0 733M 14352K select 0:00 0.00% pkid which increases over time: root@jtac-srx1500-r2003> show system processes extensive | match pki 22587 root 20 0 901M 181M select 0:03 0.00% pkid

An Insufficient Algorithmic Complexity combined with an Allocation of Resources Without Limits or Throttling vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX Series and MX Series with SPC3 allows an unauthenticated network attacker to cause latency in transit packet processing and even packet loss. If transit traffic includes a significant percentage (> 5%) of fragmented packets which need to be reassembled, high latency or packet drops might be observed. This issue affects Juniper Networks Junos OS on SRX Series, MX Series with SPC3: All versions prior to 18.2R3; 18.3 versions prior to 18.3R3; 18.4 versions prior to 18.4R2-S9, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S1, 19.2R2.

A Stack-based Buffer Overflow vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on MX Series and SRX series allows an unauthenticated networked attacker to cause a flowd crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue can be triggered by a specific Session Initiation Protocol (SIP) invite packet if the SIP ALG is enabled. Due to this, the PIC will be rebooted and all traffic that traverses the PIC will be dropped. This issue affects: Juniper Networks Junos OS 20.4 versions prior to 20.4R3-S2; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2; 21.3 versions prior to 21.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packetIO daemon of Juniper Networks Junos OS Evolved on PTX10003, PTX10004, and PTX10008 allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). Continued receipt of these crafted packets will cause a sustained Denial of Service condition. This issue affects Juniper Networks Junos OS Evolved all versions prior to 20.4R2-S3-EVO on PTX10003, PTX10004, and PTX10008. This issue does not affect: Juniper Networks Junos OS Evolved versions 21.1R1-EVO and above; Juniper Networks Junos OS.

A NULL Pointer Dereference vulnerability in the Packet Forwarding Engine of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On SRX Series If Unified Threat Management (UTM) Enhanced Content Filtering (CF) is enabled and specific transit traffic is processed the PFE will crash and restart. This issue affects Juniper Networks Junos OS: 21.4 versions prior to 21.4R1-S2, 21.4R2 on SRX Series; 22.1 versions prior to 22.1R1-S1, 22.1R2 on SRX Series. This issue does not affect Juniper Networks Junos OS versions prior to 21.4R1.

A Missing Release of Resource after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause a Denial of Service (DoS) by sending specific packets over VXLAN which cause heap memory to leak and on exhaustion the PFE to reset. The heap memory utilization can be monitored with the command: user@host> show chassis fpc This issue affects: Juniper Networks Junos OS 19.4 versions prior to 19.4R2-S6, 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2. This issue does not affect versions of Junos OS prior to 19.4R1.

On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a malformed DHCPv6 packet is received, resulting with the restart of the daemon. This issue only affects DHCPv6, it does not affect DHCPv4. This issue affects: Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.2 version 19.2R2 and later versions; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2; This issue does not affect Juniper Networks Junos OS prior to 17.4R1.

A vulnerability in the BGP FlowSpec implementation may cause a Juniper Networks Junos OS device to terminate an established BGP session upon receiving a specific BGP FlowSpec advertisement. The BGP NOTIFICATION message that terminates an established BGP session is sent toward the peer device that originally sent the specific BGP FlowSpec advertisement. This specific BGP FlowSpec advertisement received from a BGP peer might get propagated from a Junos OS device running the fixed release to another device that is vulnerable causing BGP session termination downstream. This issue affects IPv4 and IPv6 BGP FlowSpec deployment. This issue affects Juniper Networks Junos OS: 12.3; 12.3X48 on SRX Series; 14.1X53 on EX and QFX Series; 15.1 versions prior to 15.1R7-S5; 15.1F versions prior to 15.1F6-S13; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D497 on NFX Series; 15.1X53 versions prior to 15.1X53-D592 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S7; 17.1 versions prior to 17.1R2-S12, 17.1R3; 17.2 versions prior to 17.2R2-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S5; 17.4 versions prior to 17.4R1-S8, 17.4R2; 18.1 versions prior to 18.1R2-S4, 18.1R3; 18.2X75 versions prior to 18.2X75-D20.

On Juniper Networks Junos OS devices, a stream of TCP packets sent to the Routing Engine (RE) may cause mbuf leak which can lead to Flexible PIC Concentrator (FPC) crash or the system to crash and restart (vmcore). This issue can be trigged by IPv4 or IPv6 and it is caused only by TCP packets. This issue is not related to any specific configuration and it affects Junos OS releases starting from 17.4R1. However, this issue does not affect Junos OS releases prior to 18.2R1 when Nonstop active routing (NSR) is configured [edit routing-options nonstop-routing]. The number of mbufs is platform dependent. The following command provides the number of mbufs counter that are currently in use and maximum number of mbufs that can be allocated on a platform: user@host> show system buffers 2437/3143/5580 mbufs in use (current/cache/total) Once the device runs out of mbufs, the FPC crashes or the vmcore occurs and the device might become inaccessible requiring a manual restart. This issue affects Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D420.12, 18.2X75-D51, 18.2X75-D60, 18.2X75-D34; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Versions of Junos OS prior to 17.4R1 are unaffected by this vulnerability.

On Juniper Networks SRX Series configured with application identification inspection enabled, receipt of specific HTTP traffic can cause high CPU load utilization, which could lead to traffic interruption. Application identification is enabled by default and is automatically turned on when Intrusion Detection and Prevention (IDP), AppFW, AppQoS, or AppTrack is configured. Thus, this issue might occur when IDP, AppFW, AppQoS, or AppTrack is configured. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D105; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230; 17.4 versions prior to 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S5, 18.4R3-S1; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2.

On Juniper Networks PTX and QFX Series devices with packet sampling configured using tunnel-observation mpls-over-udp, sampling of a malformed packet can cause the Kernel Routing Table (KRT) queue to become stuck. KRT is the module within the Routing Process Daemon (RPD) that synchronized the routing tables with the forwarding tables in the kernel. This table is then synchronized to the Packet Forwarding Engine (PFE) via the KRT queue. Thus, when KRT queue become stuck, it can lead to unexpected packet forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. When this issue occurs, the following message might appear in the /var/log/messages: DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 DATE DEVICE kernel: %KERN-3: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (7297134592) Current delayed unref = (60000), Current unique delayed unref = (18420), Max delayed unref on this platform = (40000) Current delayed weight unref = (60000) Max delayed weight unref on this platform= (400000) curproc = rpd This issue affects Juniper Networks Junos OS on PTX/QFX Series: 17.2X75 versions prior to 17.2X75-D105; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D420, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R1-S7, 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2. This issue does not affect Juniper Networks Junos OS prior to 18.1R1.

On Juniper Networks Junos OS devices, a specific SNMP OID poll causes a memory leak which over time leads to a kernel crash (vmcore). Prior to the kernel crash other processes might be impacted, such as failure to establish SSH connection to the device. The administrator can monitor the output of the following command to check if there is memory leak caused by this issue: user@device> show system virtual-memory | match "pfe_ipc|kmem" pfe_ipc 147 5K - 164352 16,32,64,8192 <-- increasing vm.kmem_map_free: 127246336 <-- decreasing pfe_ipc 0 0K - 18598 32,8192 vm.kmem_map_free: 134582272 This issue affects Juniper Networks Junos OS: 17.4R3; 18.1 version 18.1R3-S5 and later versions prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions prior to 18.2R3-S3; 18.2X75 version 18.2X75-D420, 18.2X75-D50 and later versions prior to 18.2X75-D430, 18.2X75-D53, 18.2X75-D60; 18.3 version 18.3R3 and later versions prior to 18.3R3-S2; 18.4 version 18.4R1-S4, 18.4R2 and later versions prior to 18.4R2-S5, 18.4R3-S1; 19.1 version 19.1R2 and later versions prior to 19.1R2-S2, 19.1R3; 19.2 version 19.2R1 and later versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2. This issue does not affect Juniper Networks Junos OS prior to 17.4R3.

On Juniper Networks Junos OS and Junos OS Evolved devices, BGP session flapping can lead to a routing process daemon (RPD) crash and restart, limiting the attack surface to configured BGP peers. This issue only affects devices with BGP damping in combination with accepted-prefix-limit configuration. When the issue occurs the following messages will appear in the /var/log/messages: rpd[6046]: %DAEMON-4-BGP_PREFIX_THRESH_EXCEEDED: XXXX (External AS x): Configured maximum accepted prefix-limit threshold(1800) exceeded for inet6-unicast nlri: 1984 (instance master) rpd[6046]: %DAEMON-3-BGP_CEASE_PREFIX_LIMIT_EXCEEDED: 2001:x:x:x::2 (External AS x): Shutting down peer due to exceeding configured maximum accepted prefix-limit(2000) for inet6-unicast nlri: 2001 (instance master) rpd[6046]: %DAEMON-4: bgp_rt_maxprefixes_check_common:9284: NOTIFICATION sent to 2001:x:x:x::2 (External AS x): code 6 (Cease) subcode 1 (Maximum Number of Prefixes Reached) AFI: 2 SAFI: 1 prefix limit 2000 kernel: %KERN-5: mastership_relinquish_on_process_exit: RPD crashed on master RE. Sending SIGUSR2 to chassisd (5612:chassisd) to trigger RE switchover This issue affects: Juniper Networks Junos OS: 17.2R3-S3; 17.3 version 17.3R3-S3 and later versions, prior to 17.3R3-S8; 17.4 version 17.4R2-S4, 17.4R3 and later versions, prior to 17.4R2-S10, 17.4R3-S2; 18.1 version 18.1R3-S6 and later versions, prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions, prior to 18.2R3-S4; 18.2X75 version 18.2X75-D50, 18.2X75-D60 and later versions, prior to 18.2X75-D53, 18.2X75-D65; 18.3 version 18.3R2 and later versions, prior to 18.3R2-S4, 18.3R3-S2; 18.4 version 18.4R2 and later versions, prior to 18.4R2-S5, 18.4R3-S2; 19.1 version 19.1R1 and later versions, prior to 19.1R2-S2, 19.1R3-S1; 19.2 version 19.2R1 and later versions, prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R3-S3.

A vulnerability in Juniper Networks Junos OS on vMX and MX150 devices may allow an attacker to cause a Denial of Service (DoS) by sending specific packets requiring special processing in microcode that the flow cache can't handle, causing the riot forwarding daemon to crash. By continuously sending the same specific packets, an attacker can repeatedly crash the riot process causing a sustained Denial of Service. Flow cache is specific to vMX based products and the MX150, and is enabled by default in performance mode. This issue can only be triggered by traffic destined to the device. Transit traffic will not cause the riot daemon to crash. When the issue occurs, a core dump and riot log file entry are generated. For example: /var/crash/core.J-UKERN.mpc0.1557255993.3864.gz /home/pfe/RIOT logs: fpc0 riot[1888]: PANIC in lu_reorder_send_packet_postproc(): fpc0 riot[6655]: PANIC in lu_reorder_send_packet_postproc(): This issue affects Juniper Networks Junos OS: 18.1 versions prior to 18.1R3 on vMX and MX150; 18.2 versions prior to 18.2R3 on vMX and MX150; 18.2X75 versions prior to 18.2X75-D60 on vMX and MX150; 18.3 versions prior to 18.3R3 on vMX and MX150; 18.4 versions prior to 18.4R2 on vMX and MX150; 19.1 versions prior to 19.1R2 on vMX and MX150. This issue does not affect Junos OS versions prior to 18.1R1.

When an attacker sends a specific crafted Ethernet Operation, Administration, and Maintenance (Ethernet OAM) packet to a target device, it may improperly handle the incoming malformed data and fail to sanitize this incoming data resulting in an overflow condition. This overflow condition in Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) condition by coring the CFM daemon. Continued receipt of these packets may cause an extended Denial of Service condition. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95 on SRX Series; 14.1X50 versions prior to 14.1X50-D145; 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R2; 15.1X49 versions prior to 15.1X49-D170 on SRX Series; 15.1X53 versions prior to 15.1X53-D67.

A Reachable Assertion vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows to send specific genuine PIM packets to the device resulting in rpd to crash causing a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Note: This issue is not noticed when all the devices in the network are Juniper devices. This issue affects Juniper Networks: Junos OS: * All versions prior to 20.4R3-S7; * 21.2 versions prior to 21.2R3-S5; * 21.3 versions prior to 21.3R3-S4; * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3; * 22.3 versions prior to 22.3R3; * 22.4 versions prior to 22.4R3. Junos OS Evolved: * All versions prior to 22.3R3-EVO; * 22.4-EVO versions prior to 22.4R3-EVO; * 23.2-EVO versions prior to 23.2R1-EVO.

Receipt of a malformed BGP OPEN message may cause the routing protocol daemon (rpd) process to crash and restart. By continuously sending specially crafted BGP OPEN messages, an attacker can repeatedly crash the rpd process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.3 prior to 12.3R12-S4, 12.3R13, 12.3R3-S4; 12.3X48 prior to 12.3X48-D50; 13.3 prior to 13.3R4-S11, 13.3R10; 14.1 prior to 14.1R8-S3, 14.1R9; 14.1X53 prior to 14.1X53-D40; 14.1X55 prior to 14.1X55-D35; 14.2 prior to 14.2R4-S7, 14.2R6-S4, 14.2R7; 15.1 prior to 15.1F2-S11, 15.1F4-S1-J1, 15.1F5-S3, 15.1F6, 15.1R4; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D33, 15.1X53-D50.

An Out-of-Bounds Write vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On all Junos OS and Junos OS Evolved devices an rpd crash and restart can occur while processing BGP route updates received over an established BGP session. This specific issue is observed for BGP routes learned via a peer which is configured with a BGP import policy that has hundreds of terms matching IPv4 and/or IPv6 prefixes. This issue affects Juniper Networks Junos OS: * All versions prior to 20.4R3-S8; * 21.1 version 21.1R1 and later versions; * 21.2 versions prior to 21.2R3-S2; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R2-S1, 21.4R3-S5. This issue affects Juniper Networks Junos OS Evolved: * All versions prior to 20.4R3-S8-EVO; * 21.1-EVO version 21.1R1-EVO and later versions; * 21.2-EVO versions prior to 21.2R3-S2-EVO; * 21.3-EVO version 21.3R1-EVO and later versions; * 21.4-EVO versions prior to 21.4R2-S1-EVO, 21.4R3-S5-EVO.

Certain types of malformed Path Computation Element Protocol (PCEP) packets when received and processed by a Juniper Networks Junos OS device serving as a Path Computation Client (PCC) in a PCEP environment using Juniper's path computational element protocol daemon (pccd) process allows an attacker to cause the pccd process to crash and generate a core file thereby causing a Denial of Service (DoS). Continued receipt of this family of malformed PCEP packets will cause an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1F6-S13, 15.1R7-S4; 15.1X49 versions prior to 15.1X49-D180 on SRX Series; 15.1X53 versions prior to 15.1X53-D238, 15.1X53-D496, 15.1X53-D592; 16.1 versions prior to 16.1R7-S4; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R2-S11, 17.1R3; 17.2 versions prior to 17.2R1-S9; 17.2 version 17.2R2 and later prior to 17.2R3-S2; 17.3 versions prior to 17.3R3-S3; 17.4 versions prior to 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2-S6, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. This issue does not affect releases of Junos OS prior to 15.1R1.

An Out-of-bounds Read vulnerability in Juniper Networks Junos OS and Junos OS Evolved's routing protocol daemon (rpd) allows an unauthenticated, network-based attacker to send malformed BGP packets to a device configured with packet receive trace options enabled to crash rpd. This issue affects: Junos OS:  * from 21.2R3-S8 before 21.2R3-S9,  * from 21.4R3-S7 before 21.4R3-S9,  * from 22.2R3-S4 before 22.2R3-S5,  * from 22.3R3-S2 before 22.3R3-S4,  * from 22.4R3 before 22.4R3-S5,  * from 23.2R2 before 23.2R2-S2,  * from 23.4R1 before 23.4R2-S1,  * from 24.2R1 before 24.2R1-S1, 24.2R2. Junos OS Evolved: * from 21.4R3-S7-EVO before 21.4R3-S9-EVO,  * from 22.2R3-S4-EVO before 22.2R3-S5-EVO,  * from 22.3R3-S2-EVO before 22.3R3-S4-EVO,  * from 22.4R3-EVO before 22.4R3-S5-EVO,  * from 23.2R2-EVO before 23.2R2-S2-EVO,  * from 23.4R1-EVO before 23.4R2-S1-EVO,  * from 24.2R1-EVO before 24.2R1-S2-EVO, 24.2R2-EVO. This issue requires a BGP session to be established. This issue can propagate and multiply through multiple ASes until reaching vulnerable devices. This issue affects iBGP and eBGP. This issue affects IPv4 and IPv6. An indicator of compromise may be the presence of malformed update messages in a neighboring AS which is unaffected by this issue: For example, by issuing the command on the neighboring device:  show log messages Reviewing for similar messages from devices within proximity to each other may indicate this malformed packet is propagating:   rpd[<pid>]: Received malformed update from <IP address> (External AS <AS#>) and   rpd[<pid>]: Malformed Attribute

An Improper Following of Specification by Caller vulnerability in web management (J-Web, Captive Portal, 802.1X, Juniper Secure Connect (JSC) of Juniper Networks Junos OS on SRX Series, EX Series, MX240, MX480, MX960, QFX5120 Series, allows an unauthenticated, network-based attacker, sending genuine traffic targeted to the device to cause the CPU to climb until the device becomes unresponsive. Continuous receipt of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Junos OS:  * All versions before 21.4R3-S9, * from 22.2 before 22.2R3-S5, * from 22.4 before 22.4R3-S4, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S3, * from 24.2 before 24.2R1-S1, 24.2R2. An indicator of compromise is to review the CPU % of the httpd process in the CLI: e.g.   show system processes extensive | match httpd  PID nobody       52   0   20M    191M select   2   0:01   80.00% httpd{httpd} <<<<< the percentage of httpd usage if high may be an indicator

A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Tunnel Driver (jtd) of Juniper Networks Junos OS Evolved allows an unauthenticated network-based attacker to cause Denial of Service.  Receipt of specifically malformed IPv6 packets, destined to the device, causes kernel memory to not be freed, resulting in memory exhaustion leading to a system crash and Denial of Service (DoS). Continuous receipt and processing of these packets will continue to exhaust kernel memory, creating a sustained Denial of Service (DoS) condition. This issue only affects systems configured with IPv6. This issue affects Junos OS Evolved:  * from 22.4-EVO before 22.4R3-S5-EVO,  * from 23.2-EVO before 23.2R2-S2-EVO,  * from 23.4-EVO before 23.4R2-S2-EVO,  * from 24.2-EVO before 24.2R1-S2-EVO, 24.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 22.4R1-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the pfe (packet forwarding engine) of Juniper Networks Junos OS on MX Series causes a port within a pool to be blocked leading to Denial of Service (DoS). In a DS-Lite (Dual-Stack Lite) and NAT (Network Address Translation) scenario, when crafted IPv6 traffic is received and prefix-length is set to 56, the ports assigned to the user will not be freed.  Eventually, users cannot establish new connections. Affected FPC/PIC need to be manually restarted to recover. Following is the command to identify the issue:      user@host> show services nat source port-block      Host_IP                     External_IP                   Port_Block      Ports_Used/       Block_State/                                                               Range           Ports_Total       Left_Time(s)     2001::                        x.x.x.x                     58880-59391     256/256*1         Active/-       >>>>>>>>port still usedThis issue affects Junos OS on MX Series:  * from 21.2 before 21.2R3-S8,  * from 21.4 before 21.4R3-S7,  * from 22.1 before 22.1R3-S6,  * from 22.2 before 22.2R3-S4,  * from 22.3 before 22.3R3-S3,  * from 22.4 before 22.4R3-S2,  * from 23.2 before 23.2R2-S1,  * from 23.4 before 23.4R1-S2, 23.4R2. This issue does not affect versions before 20.2R1.

A sustained sequence of different types of normal transit traffic can trigger a high CPU consumption denial of service condition in the Junos OS register and schedule software interrupt handler subsystem when a specific command is issued to the device. This affects one or more threads and conversely one or more running processes running on the system. Once this occurs, the high CPU event(s) affects either or both the forwarding and control plane. As a result of this condition the device can become inaccessible in either or both the control and forwarding plane and stops forwarding traffic until the device is rebooted. The issue will reoccur after reboot upon receiving further transit traffic. Score: 5.7 MEDIUM (CVSS:3.0/AV:A/AC:L/PR:N/UI:R/S:U/C:N/I:N/A:H) For network designs utilizing layer 3 forwarding agents or other ARP through layer 3 technologies, the score is slightly higher. Score: 6.5 MEDIUM (CVSS:3.0/AV:N/AC:L/PR:N/UI:R/S:U/C:N/I:N/A:H) If the following entry exists in the RE message logs then this may indicate the issue is present. This entry may or may not appear when this issue occurs. /kernel: Expensive timeout(9) function: Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D50; 12.3X48 versions prior to 12.3X48-D30; 12.3R versions prior to 12.3R12-S7; 14.1 versions prior to 14.1R8-S4, 14.1R9; 14.1X53 versions prior to 14.1X53-D30, 14.1X53-D34; 14.2 versions prior to 14.2R8; 15.1 versions prior to 15.1F6, 15.1R3; 15.1X49 versions prior to 15.1X49-D40; 15.1X53 versions prior to 15.1X53-D31, 15.1X53-D33, 15.1X53-D60. No other Juniper Networks products or platforms are affected by this issue.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When a BGP update message is received over an established BGP session, and that message contains a specific, optional transitive attribute, this session will be torn down with an update message error. This issue cannot propagate beyond an affected system as the processing error occurs as soon as the update is received. This issue is exploitable remotely as the respective attribute can propagate through unaffected systems and intermediate AS (if any). Continuous receipt of a BGP update containing this attribute will create a sustained Denial of Service (DoS) condition. Some customers have experienced these BGP session flaps which prompted Juniper SIRT to release this advisory out of cycle before fixed releases are widely available as there is an effective workaround. This issue affects: Juniper Networks Junos OS 15.1R1 and later versions prior to 20.4R3-S8; 21.1 version 21.1R1 and later versions prior to 21.2R3-S6; 21.3 versions prior to 21.3R3-S5; 21.4 versions prior to 21.4R3-S4; 22.1 versions prior to 22.1R3-S4; 22.2 versions prior to 22.2R3-S2; 22.3 versions prior to 22.3R2-S2, 22.3R3-S1; 22.4 versions prior to 22.4R2-S1, 22.4R3; 23.1 versions prior to 23.1R1-S1, 23.1R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S8-EVO; 21.1 version 21.1R1-EVO and later versions prior to 21.2R3-S6-EVO; 21.3 versions prior to 21.3R3-S5-EVO; 21.4 versions prior to 21.4R3-S4-EVO; 22.1 versions prior to 22.1R3-S4-EVO; 22.2 versions prior to 22.2R3-S2-EVO; 22.3 versions prior to 22.3R2-S2-EVO, 22.3R3-S1-EVO; 22.4 versions prior to 22.4R2-S1-EVO, 22.4R3-EVO; 23.1 versions prior to 23.1R1-S1-EVO, 23.1R2-EVO.

An Improper Handling of Syntactically Invalid Structure vulnerability in Object Flooding Protocol (OFP) service of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On all Junos OS Evolved platforms, when specific TCP packets are received on an open OFP port, the OFP crashes leading to a restart of Routine Engine (RE). Continuous receipt of these specific TCP packets will lead to a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS Evolved * All versions earlier than 21.2R3-S7-EVO; * 21.3 versions earlier than 21.3R3-S5-EVO ; * 21.4 versions earlier than 21.4R3-S5-EVO; * 22.1 versions earlier than 22.1R3-S4-EVO; * 22.2 versions earlier than 22.2R3-S3-EVO ; * 22.3 versions earlier than 22.3R3-EVO; * 22.4 versions earlier than 22.4R2-EVO, 22.4R3-EVO.

An Improper Handling of Inconsistent Special Elements vulnerability in the Junos Services Framework (jsf) module of Juniper Networks Junos OS allows an unauthenticated network based attacker to cause a crash in the Packet Forwarding Engine (pfe) and thereby resulting in a Denial of Service (DoS). Upon receiving malformed SSL traffic, the PFE crashes. A manual restart will be needed to recover the device. This issue only affects devices with Juniper Networks Advanced Threat Prevention (ATP) Cloud enabled with Encrypted Traffic Insights (configured via ‘security-metadata-streaming policy’). This issue affects Juniper Networks Junos OS: * All versions prior to 20.4R3-S8, 20.4R3-S9; * 21.1 version 21.1R1 and later versions; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S5; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3-S2; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2-S1, 22.4R3;

An Improper Check or Handling of Exceptional Conditions vulnerability in the UTM (Unified Threat Management) Web-Filtering feature of Juniper Networks Junos OS on SRX Series causes a jbuf memory leak to occur when accessing certain websites, eventually leading to a Denial of Service (DoS) condition. Service restoration is only possible by rebooting the system. The jbuf memory leak only occurs in SSL Proxy and UTM Web-Filtering configurations. Other products, platforms, and configurations are not affected by this vulnerability. This issue affects Juniper Networks Junos OS on SRX Series: 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R2-S1, 22.3R3; 22.4 versions prior to 22.4R1-S2, 22.4R2. This issue does not affect Juniper Networks Junos OS versions prior to 22.2R2.

An Improper Handling of Exceptional Conditions vulnerability in packet processing of Juniper Networks Junos OS on MX Series allows an unauthenticated network-based attacker to send specific packets to an Aggregated Multiservices (AMS) interface on the device, causing the packet forwarding engine (PFE) to crash, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue is only triggered by packets destined to a local-interface via a service-interface (AMS). AMS is only supported on the MS-MPC, MS-MIC, and MX-SPC3 cards. This issue is not experienced on other types of interfaces or configurations. Additionally, transit traffic does not trigger this issue. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S12; 20.2 versions prior to 20.2R3-S8; 20.4 versions prior to 20.4R3-S7; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S5; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S2; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R2-S1, 22.3R3; 22.4 versions prior to 22.4R1-S2, 22.4R2.

Juniper Junos OS 12.1X44 before 12.1X44-D50, 12.1X46 before 12.1X46-D35, 12.1X47 before 12.1X47-D25, 12.3 before 12.3R9, 12.3X48 before 12.3X48-D10, 13.2 before 13.2R7, 13.3 before 13.3R5, 14.1R3 before 14.1R3-S2, 14.1 before 14.1R4, 14.2 before 14.2R2, and 15.1 before 15.1R1 allows remote attackers to cause a denial of service (NULL pointer dereference and RDP crash) via a large number of BGP-VPLS advertisements with updated BGP local preference values.