In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Set private->all_drm_private[i]->drm to NULL if mtk_drm_bind returns err The pointer need to be set to NULL, otherwise KASAN complains about use-after-free. Because in mtk_drm_bind, all private's drm are set as follows. private->all_drm_private[i]->drm = drm; And drm will be released by drm_dev_put in case mtk_drm_kms_init returns failure. However, the shutdown path still accesses the previous allocated memory in drm_atomic_helper_shutdown. [ 84.874820] watchdog: watchdog0: watchdog did not stop! [ 86.512054] ================================================================== [ 86.513162] BUG: KASAN: use-after-free in drm_atomic_helper_shutdown+0x33c/0x378 [ 86.514258] Read of size 8 at addr ffff0000d46fc068 by task shutdown/1 [ 86.515213] [ 86.515455] CPU: 1 UID: 0 PID: 1 Comm: shutdown Not tainted 6.13.0-rc1-mtk+gfa1a78e5d24b-dirty #55 [ 86.516752] Hardware name: Unknown Product/Unknown Product, BIOS 2022.10 10/01/2022 [ 86.517960] Call trace: [ 86.518333] show_stack+0x20/0x38 (C) [ 86.518891] dump_stack_lvl+0x90/0xd0 [ 86.519443] print_report+0xf8/0x5b0 [ 86.519985] kasan_report+0xb4/0x100 [ 86.520526] __asan_report_load8_noabort+0x20/0x30 [ 86.521240] drm_atomic_helper_shutdown+0x33c/0x378 [ 86.521966] mtk_drm_shutdown+0x54/0x80 [ 86.522546] platform_shutdown+0x64/0x90 [ 86.523137] device_shutdown+0x260/0x5b8 [ 86.523728] kernel_restart+0x78/0xf0 [ 86.524282] __do_sys_reboot+0x258/0x2f0 [ 86.524871] __arm64_sys_reboot+0x90/0xd8 [ 86.525473] invoke_syscall+0x74/0x268 [ 86.526041] el0_svc_common.constprop.0+0xb0/0x240 [ 86.526751] do_el0_svc+0x4c/0x70 [ 86.527251] el0_svc+0x4c/0xc0 [ 86.527719] el0t_64_sync_handler+0x144/0x168 [ 86.528367] el0t_64_sync+0x198/0x1a0 [ 86.528920] [ 86.529157] The buggy address belongs to the physical page: [ 86.529972] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0xffff0000d46fd4d0 pfn:0x1146fc [ 86.531319] flags: 0xbfffc0000000000(node=0|zone=2|lastcpupid=0xffff) [ 86.532267] raw: 0bfffc0000000000 0000000000000000 dead000000000122 0000000000000000 [ 86.533390] raw: ffff0000d46fd4d0 0000000000000000 00000000ffffffff 0000000000000000 [ 86.534511] page dumped because: kasan: bad access detected [ 86.535323] [ 86.535559] Memory state around the buggy address: [ 86.536265] ffff0000d46fbf00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 86.537314] ffff0000d46fbf80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 86.538363] >ffff0000d46fc000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 86.544733] ^ [ 86.551057] ffff0000d46fc080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 86.557510] ffff0000d46fc100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff [ 86.563928] ================================================================== [ 86.571093] Disabling lock debugging due to kernel taint [ 86.577642] Unable to handle kernel paging request at virtual address e0e9c0920000000b [ 86.581834] KASAN: maybe wild-memory-access in range [0x0752049000000058-0x075204900000005f] ...

In the Linux kernel, the following vulnerability has been resolved: memory: tegra20-emc: fix an OF node reference bug in tegra_emc_find_node_by_ram_code() As of_find_node_by_name() release the reference of the argument device node, tegra_emc_find_node_by_ram_code() releases some device nodes while still in use, resulting in possible UAFs. According to the bindings and the in-tree DTS files, the "emc-tables" node is always device's child node with the property "nvidia,use-ram-code", and the "lpddr2" node is a child of the "emc-tables" node. Thus utilize the for_each_child_of_node() macro and of_get_child_by_name() instead of of_find_node_by_name() to simplify the code. This bug was found by an experimental verification tool that I am developing. [krzysztof: applied v1, adjust the commit msg to incorporate v2 parts]

In the Linux kernel, the following vulnerability has been resolved: powerpc/pseries/vas: Add close() callback in vas_vm_ops struct The mapping VMA address is saved in VAS window struct when the paste address is mapped. This VMA address is used during migration to unmap the paste address if the window is active. The paste address mapping will be removed when the window is closed or with the munmap(). But the VMA address in the VAS window is not updated with munmap() which is causing invalid access during migration. The KASAN report shows: [16386.254991] BUG: KASAN: slab-use-after-free in reconfig_close_windows+0x1a0/0x4e8 [16386.255043] Read of size 8 at addr c00000014a819670 by task drmgr/696928 [16386.255096] CPU: 29 UID: 0 PID: 696928 Comm: drmgr Kdump: loaded Tainted: G B 6.11.0-rc5-nxgzip #2 [16386.255128] Tainted: [B]=BAD_PAGE [16386.255148] Hardware name: IBM,9080-HEX Power11 (architected) 0x820200 0xf000007 of:IBM,FW1110.00 (NH1110_016) hv:phyp pSeries [16386.255181] Call Trace: [16386.255202] [c00000016b297660] [c0000000018ad0ac] dump_stack_lvl+0x84/0xe8 (unreliable) [16386.255246] [c00000016b297690] [c0000000006e8a90] print_report+0x19c/0x764 [16386.255285] [c00000016b297760] [c0000000006e9490] kasan_report+0x128/0x1f8 [16386.255309] [c00000016b297880] [c0000000006eb5c8] __asan_load8+0xac/0xe0 [16386.255326] [c00000016b2978a0] [c00000000013f898] reconfig_close_windows+0x1a0/0x4e8 [16386.255343] [c00000016b297990] [c000000000140e58] vas_migration_handler+0x3a4/0x3fc [16386.255368] [c00000016b297a90] [c000000000128848] pseries_migrate_partition+0x4c/0x4c4 ... [16386.256136] Allocated by task 696554 on cpu 31 at 16377.277618s: [16386.256149] kasan_save_stack+0x34/0x68 [16386.256163] kasan_save_track+0x34/0x80 [16386.256175] kasan_save_alloc_info+0x58/0x74 [16386.256196] __kasan_slab_alloc+0xb8/0xdc [16386.256209] kmem_cache_alloc_noprof+0x200/0x3d0 [16386.256225] vm_area_alloc+0x44/0x150 [16386.256245] mmap_region+0x214/0x10c4 [16386.256265] do_mmap+0x5fc/0x750 [16386.256277] vm_mmap_pgoff+0x14c/0x24c [16386.256292] ksys_mmap_pgoff+0x20c/0x348 [16386.256303] sys_mmap+0xd0/0x160 ... [16386.256350] Freed by task 0 on cpu 31 at 16386.204848s: [16386.256363] kasan_save_stack+0x34/0x68 [16386.256374] kasan_save_track+0x34/0x80 [16386.256384] kasan_save_free_info+0x64/0x10c [16386.256396] __kasan_slab_free+0x120/0x204 [16386.256415] kmem_cache_free+0x128/0x450 [16386.256428] vm_area_free_rcu_cb+0xa8/0xd8 [16386.256441] rcu_do_batch+0x2c8/0xcf0 [16386.256458] rcu_core+0x378/0x3c4 [16386.256473] handle_softirqs+0x20c/0x60c [16386.256495] do_softirq_own_stack+0x6c/0x88 [16386.256509] do_softirq_own_stack+0x58/0x88 [16386.256521] __irq_exit_rcu+0x1a4/0x20c [16386.256533] irq_exit+0x20/0x38 [16386.256544] interrupt_async_exit_prepare.constprop.0+0x18/0x2c ... [16386.256717] Last potentially related work creation: [16386.256729] kasan_save_stack+0x34/0x68 [16386.256741] __kasan_record_aux_stack+0xcc/0x12c [16386.256753] __call_rcu_common.constprop.0+0x94/0xd04 [16386.256766] vm_area_free+0x28/0x3c [16386.256778] remove_vma+0xf4/0x114 [16386.256797] do_vmi_align_munmap.constprop.0+0x684/0x870 [16386.256811] __vm_munmap+0xe0/0x1f8 [16386.256821] sys_munmap+0x54/0x6c [16386.256830] system_call_exception+0x1a0/0x4a0 [16386.256841] system_call_vectored_common+0x15c/0x2ec [16386.256868] The buggy address belongs to the object at c00000014a819670 which belongs to the cache vm_area_struct of size 168 [16386.256887] The buggy address is located 0 bytes inside of freed 168-byte region [c00000014a819670, c00000014a819718) [16386.256915] The buggy address belongs to the physical page: [16386.256928] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x14a81 [16386.256950] memcg:c0000000ba430001 [16386.256961] anon flags: 0x43ffff800000000(node=4|zone=0|lastcpupid=0x7ffff) [16386.256975] page_type: 0xfdffffff(slab) [16386 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm: adv7511: Fix use-after-free in adv7533_attach_dsi() The host_node pointer was assigned and freed in adv7533_parse_dt(), and later, adv7533_attach_dsi() uses the same. Fix this use-after-free issue by dropping of_node_put() in adv7533_parse_dt() and calling of_node_put() in error path of probe() and also in the remove().

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Remove cache tags before disabling ATS The current implementation removes cache tags after disabling ATS, leading to potential memory leaks and kernel crashes. Specifically, CACHE_TAG_DEVTLB type cache tags may still remain in the list even after the domain is freed, causing a use-after-free condition. This issue really shows up when multiple VFs from different PFs passed through to a single user-space process via vfio-pci. In such cases, the kernel may crash with kernel messages like: BUG: kernel NULL pointer dereference, address: 0000000000000014 PGD 19036a067 P4D 1940a3067 PUD 136c9b067 PMD 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 74 UID: 0 PID: 3183 Comm: testCli Not tainted 6.11.9 #2 RIP: 0010:cache_tag_flush_range+0x9b/0x250 Call Trace: <TASK> ? __die+0x1f/0x60 ? page_fault_oops+0x163/0x590 ? exc_page_fault+0x72/0x190 ? asm_exc_page_fault+0x22/0x30 ? cache_tag_flush_range+0x9b/0x250 ? cache_tag_flush_range+0x5d/0x250 intel_iommu_tlb_sync+0x29/0x40 intel_iommu_unmap_pages+0xfe/0x160 __iommu_unmap+0xd8/0x1a0 vfio_unmap_unpin+0x182/0x340 [vfio_iommu_type1] vfio_remove_dma+0x2a/0xb0 [vfio_iommu_type1] vfio_iommu_type1_ioctl+0xafa/0x18e0 [vfio_iommu_type1] Move cache_tag_unassign_domain() before iommu_disable_pci_caps() to fix it.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix use-after-free when COWing tree bock and tracing is enabled When a COWing a tree block, at btrfs_cow_block(), and we have the tracepoint trace_btrfs_cow_block() enabled and preemption is also enabled (CONFIG_PREEMPT=y), we can trigger a use-after-free in the COWed extent buffer while inside the tracepoint code. This is because in some paths that call btrfs_cow_block(), such as btrfs_search_slot(), we are holding the last reference on the extent buffer @buf so btrfs_force_cow_block() drops the last reference on the @buf extent buffer when it calls free_extent_buffer_stale(buf), which schedules the release of the extent buffer with RCU. This means that if we are on a kernel with preemption, the current task may be preempted before calling trace_btrfs_cow_block() and the extent buffer already released by the time trace_btrfs_cow_block() is called, resulting in a use-after-free. Fix this by moving the trace_btrfs_cow_block() from btrfs_cow_block() to btrfs_force_cow_block() before the COWed extent buffer is freed. This also has a side effect of invoking the tracepoint in the tree defrag code, at defrag.c:btrfs_realloc_node(), since btrfs_force_cow_block() is called there, but this is fine and it was actually missing there.

In the Linux kernel, the following vulnerability has been resolved: RDMA/siw: Remove direct link to net_device Do not manage a per device direct link to net_device. Rely on associated ib_devices net_device management, not doubling the effort locally. A badly managed local link to net_device was causing a 'KASAN: slab-use-after-free' exception during siw_query_port() call.

In the Linux kernel, the following vulnerability has been resolved: iio: mma8452: Fix trigger reference couting The mma8452 driver directly assigns a trigger to the struct iio_dev. The IIO core when done using this trigger will call `iio_trigger_put()` to drop the reference count by 1. Without the matching `iio_trigger_get()` in the driver the reference count can reach 0 too early, the trigger gets freed while still in use and a use-after-free occurs. Fix this by getting a reference to the trigger before assigning it to the IIO device.

In the Linux kernel, the following vulnerability has been resolved: watchdog: Fix possible use-after-free by calling del_timer_sync() This driver's remove path calls del_timer(). However, that function does not wait until the timer handler finishes. This means that the timer handler may still be running after the driver's remove function has finished, which would result in a use-after-free. Fix by calling del_timer_sync(), which makes sure the timer handler has finished, and unable to re-schedule itself.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: L2CAP: do not leave dangling sk pointer on error in l2cap_sock_create() bt_sock_alloc() allocates the sk object and attaches it to the provided sock object. On error l2cap_sock_alloc() frees the sk object, but the dangling pointer is still attached to the sock object, which may create use-after-free in other code.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix usage slab after free [ +0.000021] BUG: KASAN: slab-use-after-free in drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000027] Read of size 8 at addr ffff8881b8605f88 by task amd_pci_unplug/2147 [ +0.000023] CPU: 6 PID: 2147 Comm: amd_pci_unplug Not tainted 6.10.0+ #1 [ +0.000016] Hardware name: ASUS System Product Name/ROG STRIX B550-F GAMING (WI-FI), BIOS 1401 12/03/2020 [ +0.000016] Call Trace: [ +0.000008] <TASK> [ +0.000009] dump_stack_lvl+0x76/0xa0 [ +0.000017] print_report+0xce/0x5f0 [ +0.000017] ? drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000019] ? srso_return_thunk+0x5/0x5f [ +0.000015] ? kasan_complete_mode_report_info+0x72/0x200 [ +0.000016] ? drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000019] kasan_report+0xbe/0x110 [ +0.000015] ? drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000023] __asan_report_load8_noabort+0x14/0x30 [ +0.000014] drm_sched_entity_flush+0x6cb/0x7a0 [gpu_sched] [ +0.000020] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? __kasan_check_write+0x14/0x30 [ +0.000016] ? __pfx_drm_sched_entity_flush+0x10/0x10 [gpu_sched] [ +0.000020] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? __kasan_check_write+0x14/0x30 [ +0.000013] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? enable_work+0x124/0x220 [ +0.000015] ? __pfx_enable_work+0x10/0x10 [ +0.000013] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? free_large_kmalloc+0x85/0xf0 [ +0.000016] drm_sched_entity_destroy+0x18/0x30 [gpu_sched] [ +0.000020] amdgpu_vce_sw_fini+0x55/0x170 [amdgpu] [ +0.000735] ? __kasan_check_read+0x11/0x20 [ +0.000016] vce_v4_0_sw_fini+0x80/0x110 [amdgpu] [ +0.000726] amdgpu_device_fini_sw+0x331/0xfc0 [amdgpu] [ +0.000679] ? mutex_unlock+0x80/0xe0 [ +0.000017] ? __pfx_amdgpu_device_fini_sw+0x10/0x10 [amdgpu] [ +0.000662] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? __kasan_check_write+0x14/0x30 [ +0.000013] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? mutex_unlock+0x80/0xe0 [ +0.000016] amdgpu_driver_release_kms+0x16/0x80 [amdgpu] [ +0.000663] drm_minor_release+0xc9/0x140 [drm] [ +0.000081] drm_release+0x1fd/0x390 [drm] [ +0.000082] __fput+0x36c/0xad0 [ +0.000018] __fput_sync+0x3c/0x50 [ +0.000014] __x64_sys_close+0x7d/0xe0 [ +0.000014] x64_sys_call+0x1bc6/0x2680 [ +0.000014] do_syscall_64+0x70/0x130 [ +0.000014] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? irqentry_exit_to_user_mode+0x60/0x190 [ +0.000015] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? irqentry_exit+0x43/0x50 [ +0.000012] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? exc_page_fault+0x7c/0x110 [ +0.000015] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ +0.000014] RIP: 0033:0x7ffff7b14f67 [ +0.000013] Code: ff e8 0d 16 02 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 03 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 41 c3 48 83 ec 18 89 7c 24 0c e8 73 ba f7 ff [ +0.000026] RSP: 002b:00007fffffffe378 EFLAGS: 00000246 ORIG_RAX: 0000000000000003 [ +0.000019] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ffff7b14f67 [ +0.000014] RDX: 0000000000000000 RSI: 00007ffff7f6f47a RDI: 0000000000000003 [ +0.000014] RBP: 00007fffffffe3a0 R08: 0000555555569890 R09: 0000000000000000 [ +0.000014] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fffffffe5c8 [ +0.000013] R13: 00005555555552a9 R14: 0000555555557d48 R15: 00007ffff7ffd040 [ +0.000020] </TASK> [ +0.000016] Allocated by task 383 on cpu 7 at 26.880319s: [ +0.000014] kasan_save_stack+0x28/0x60 [ +0.000008] kasan_save_track+0x18/0x70 [ +0.000007] kasan_save_alloc_info+0x38/0x60 [ +0.000007] __kasan_kmalloc+0xc1/0xd0 [ +0.000007] kmalloc_trace_noprof+0x180/0x380 [ +0.000007] drm_sched_init+0x411/0xec0 [gpu_sched] [ +0.000012] amdgpu_device_init+0x695f/0xa610 [amdgpu] [ +0.000658] amdgpu_driver_load_kms+0x1a/0x120 [amdgpu] [ +0.000662] amdgpu_pci_p ---truncated---

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: core: Fix invalid error returning in mhi_queue mhi_queue returns an error when the doorbell is not accessible in the current state. This can happen when the device is in non M0 state, like M3, and needs to be waken-up prior ringing the DB. This case is managed earlier by triggering an asynchronous M3 exit via controller resume/suspend callbacks, that in turn will cause M0 transition and DB update. So, since it's not an error but just delaying of doorbell update, there is no reason to return an error. This also fixes a use after free error for skb case, indeed a caller queuing skb will try to free the skb if the queueing fails, but in that case queueing has been done.

In the Linux kernel, the following vulnerability has been resolved: nfsd: make sure exp active before svc_export_show The function `e_show` was called with protection from RCU. This only ensures that `exp` will not be freed. Therefore, the reference count for `exp` can drop to zero, which will trigger a refcount use-after-free warning when `exp_get` is called. To resolve this issue, use `cache_get_rcu` to ensure that `exp` remains active. ------------[ cut here ]------------ refcount_t: addition on 0; use-after-free. WARNING: CPU: 3 PID: 819 at lib/refcount.c:25 refcount_warn_saturate+0xb1/0x120 CPU: 3 UID: 0 PID: 819 Comm: cat Not tainted 6.12.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014 RIP: 0010:refcount_warn_saturate+0xb1/0x120 ... Call Trace: <TASK> e_show+0x20b/0x230 [nfsd] seq_read_iter+0x589/0x770 seq_read+0x1e5/0x270 vfs_read+0x125/0x530 ksys_read+0xc1/0x160 do_syscall_64+0x5f/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e

In the Linux kernel, the following vulnerability has been resolved: ext4: fix possible UAF when remounting r/o a mmp-protected file system After commit 618f003199c6 ("ext4: fix memory leak in ext4_fill_super"), after the file system is remounted read-only, there is a race where the kmmpd thread can exit, causing sbi->s_mmp_tsk to point at freed memory, which the call to ext4_stop_mmpd() can trip over. Fix this by only allowing kmmpd() to exit when it is stopped via ext4_stop_mmpd(). Bug-Report-Link: <20210629143603.2166962-1-yebin10@huawei.com>

In the Linux kernel, the following vulnerability has been resolved: net: ieee802154: do not leave a dangling sk pointer in ieee802154_create() sock_init_data() attaches the allocated sk object to the provided sock object. If ieee802154_create() fails later, the allocated sk object is freed, but the dangling pointer remains in the provided sock object, which may allow use-after-free. Clear the sk pointer in the sock object on error.

In the Linux kernel, the following vulnerability has been resolved: jfs: array-index-out-of-bounds fix in dtReadFirst The value of stbl can be sometimes out of bounds due to a bad filesystem. Added a check with appopriate return of error code in that case.

In the Linux kernel, the following vulnerability has been resolved: HID: betop: fix slab-out-of-bounds Write in betop_probe Syzbot reported slab-out-of-bounds Write bug in hid-betopff driver. The problem is the driver assumes the device must have an input report but some malicious devices violate this assumption. So this patch checks hid_device's input is non empty before it's been used.

In the Linux kernel, the following vulnerability has been resolved: net: af_can: do not leave a dangling sk pointer in can_create() On error can_create() frees the allocated sk object, but sock_init_data() has already attached it to the provided sock object. This will leave a dangling sk pointer in the sock object and may cause use-after-free later.

In the Linux kernel, the following vulnerability has been resolved: ACPI: custom_method: fix potential use-after-free issue In cm_write(), buf is always freed when reaching the end of the function. If the requested count is less than table.length, the allocated buffer will be freed but subsequent calls to cm_write() will still try to access it. Remove the unconditional kfree(buf) at the end of the function and set the buf to NULL in the -EINVAL error path to match the rest of function.

In the Linux kernel, the following vulnerability has been resolved: regmap: set debugfs_name to NULL after it is freed There is a upstream commit cffa4b2122f5("regmap:debugfs: Fix a memory leak when calling regmap_attach_dev") that adds a if condition when create name for debugfs_name. With below function invoking logical, debugfs_name is freed in regmap_debugfs_exit(), but it is not created again because of the if condition introduced by above commit. regmap_reinit_cache() regmap_debugfs_exit() ... regmap_debugfs_init() So, set debugfs_name to NULL after it is freed.

Use-after-free vulnerability in fs/crypto/ in the Linux kernel before 4.10.7 allows local users to cause a denial of service (NULL pointer dereference) or possibly gain privileges by revoking keyring keys being used for ext4, f2fs, or ubifs encryption, causing cryptographic transform objects to be freed prematurely.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: bsg: Set bsg_queue to NULL after removal Currently, this does not cause any issues, but I believe it is necessary to set bsg_queue to NULL after removing it to prevent potential use-after-free (UAF) access.

The packet_set_ring function in net/packet/af_packet.c in the Linux kernel through 4.10.6 does not properly validate certain block-size data, which allows local users to cause a denial of service (integer signedness error and out-of-bounds write), or gain privileges (if the CAP_NET_RAW capability is held), via crafted system calls.

In the Linux kernel, the following vulnerability has been resolved: drm: bridge/panel: Cleanup connector on bridge detach If we don't call drm_connector_cleanup() manually in panel_bridge_detach(), the connector will be cleaned up with the other DRM objects in the call to drm_mode_config_cleanup(). However, since our drm_connector is devm-allocated, by the time drm_mode_config_cleanup() will be called, our connector will be long gone. Therefore, the connector must be cleaned up when the bridge is detached to avoid use-after-free conditions. v2: Cleanup connector only if it was created v3: Add FIXME v4: (Use connector->dev) directly in if() block

The mm subsystem in the Linux kernel through 3.2 does not properly enforce the CONFIG_STRICT_DEVMEM protection mechanism, which allows local users to read or write to kernel memory locations in the first megabyte (and bypass slab-allocation access restrictions) via an application that opens the /dev/mem file, related to arch/x86/mm/init.c and drivers/char/mem.c.

In the Linux kernel, the following vulnerability has been resolved: net: fix use-after-free in tw_timer_handler A real world panic issue was found as follow in Linux 5.4. BUG: unable to handle page fault for address: ffffde49a863de28 PGD 7e6fe62067 P4D 7e6fe62067 PUD 7e6fe63067 PMD f51e064067 PTE 0 RIP: 0010:tw_timer_handler+0x20/0x40 Call Trace: <IRQ> call_timer_fn+0x2b/0x120 run_timer_softirq+0x1ef/0x450 __do_softirq+0x10d/0x2b8 irq_exit+0xc7/0xd0 smp_apic_timer_interrupt+0x68/0x120 apic_timer_interrupt+0xf/0x20 This issue was also reported since 2017 in the thread [1], unfortunately, the issue was still can be reproduced after fixing DCCP. The ipv4_mib_exit_net is called before tcp_sk_exit_batch when a net namespace is destroyed since tcp_sk_ops is registered befrore ipv4_mib_ops, which means tcp_sk_ops is in the front of ipv4_mib_ops in the list of pernet_list. There will be a use-after-free on net->mib.net_statistics in tw_timer_handler after ipv4_mib_exit_net if there are some inflight time-wait timers. This bug is not introduced by commit f2bf415cfed7 ("mib: add net to NET_ADD_STATS_BH") since the net_statistics is a global variable instead of dynamic allocation and freeing. Actually, commit 61a7e26028b9 ("mib: put net statistics on struct net") introduces the bug since it put net statistics on struct net and free it when net namespace is destroyed. Moving init_ipv4_mibs() to the front of tcp_init() to fix this bug and replace pr_crit() with panic() since continuing is meaningless when init_ipv4_mibs() fails. [1] https://groups.google.com/g/syzkaller/c/p1tn-_Kc6l4/m/smuL_FMAAgAJ?pli=1

drivers/char/virtio_console.c in the Linux kernel 4.9.x and 4.10.x before 4.10.12 interacts incorrectly with the CONFIG_VMAP_STACK option, which allows local users to cause a denial of service (system crash or memory corruption) or possibly have unspecified other impact by leveraging use of more than one virtual page for a DMA scatterlist.

In the Linux kernel, the following vulnerability has been resolved: netfilter: ipset: add missing range check in bitmap_ip_uadt When tb[IPSET_ATTR_IP_TO] is not present but tb[IPSET_ATTR_CIDR] exists, the values of ip and ip_to are slightly swapped. Therefore, the range check for ip should be done later, but this part is missing and it seems that the vulnerability occurs. So we should add missing range checks and remove unnecessary range checks.

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_scmi: Fix slab-use-after-free in scmi_bus_notifier() The scmi_dev->name is released prematurely in __scmi_device_destroy(), which causes slab-use-after-free when accessing scmi_dev->name in scmi_bus_notifier(). So move the release of scmi_dev->name to scmi_device_release() to avoid slab-use-after-free. | BUG: KASAN: slab-use-after-free in strncmp+0xe4/0xec | Read of size 1 at addr ffffff80a482bcc0 by task swapper/0/1 | | CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.6.38-debug #1 | Hardware name: Qualcomm Technologies, Inc. SA8775P Ride (DT) | Call trace: | dump_backtrace+0x94/0x114 | show_stack+0x18/0x24 | dump_stack_lvl+0x48/0x60 | print_report+0xf4/0x5b0 | kasan_report+0xa4/0xec | __asan_report_load1_noabort+0x20/0x2c | strncmp+0xe4/0xec | scmi_bus_notifier+0x5c/0x54c | notifier_call_chain+0xb4/0x31c | blocking_notifier_call_chain+0x68/0x9c | bus_notify+0x54/0x78 | device_del+0x1bc/0x840 | device_unregister+0x20/0xb4 | __scmi_device_destroy+0xac/0x280 | scmi_device_destroy+0x94/0xd0 | scmi_chan_setup+0x524/0x750 | scmi_probe+0x7fc/0x1508 | platform_probe+0xc4/0x19c | really_probe+0x32c/0x99c | __driver_probe_device+0x15c/0x3c4 | driver_probe_device+0x5c/0x170 | __driver_attach+0x1c8/0x440 | bus_for_each_dev+0xf4/0x178 | driver_attach+0x3c/0x58 | bus_add_driver+0x234/0x4d4 | driver_register+0xf4/0x3c0 | __platform_driver_register+0x60/0x88 | scmi_driver_init+0xb0/0x104 | do_one_initcall+0xb4/0x664 | kernel_init_freeable+0x3c8/0x894 | kernel_init+0x24/0x1e8 | ret_from_fork+0x10/0x20 | | Allocated by task 1: | kasan_save_stack+0x2c/0x54 | kasan_set_track+0x2c/0x40 | kasan_save_alloc_info+0x24/0x34 | __kasan_kmalloc+0xa0/0xb8 | __kmalloc_node_track_caller+0x6c/0x104 | kstrdup+0x48/0x84 | kstrdup_const+0x34/0x40 | __scmi_device_create.part.0+0x8c/0x408 | scmi_device_create+0x104/0x370 | scmi_chan_setup+0x2a0/0x750 | scmi_probe+0x7fc/0x1508 | platform_probe+0xc4/0x19c | really_probe+0x32c/0x99c | __driver_probe_device+0x15c/0x3c4 | driver_probe_device+0x5c/0x170 | __driver_attach+0x1c8/0x440 | bus_for_each_dev+0xf4/0x178 | driver_attach+0x3c/0x58 | bus_add_driver+0x234/0x4d4 | driver_register+0xf4/0x3c0 | __platform_driver_register+0x60/0x88 | scmi_driver_init+0xb0/0x104 | do_one_initcall+0xb4/0x664 | kernel_init_freeable+0x3c8/0x894 | kernel_init+0x24/0x1e8 | ret_from_fork+0x10/0x20 | | Freed by task 1: | kasan_save_stack+0x2c/0x54 | kasan_set_track+0x2c/0x40 | kasan_save_free_info+0x38/0x5c | __kasan_slab_free+0xe8/0x164 | __kmem_cache_free+0x11c/0x230 | kfree+0x70/0x130 | kfree_const+0x20/0x40 | __scmi_device_destroy+0x70/0x280 | scmi_device_destroy+0x94/0xd0 | scmi_chan_setup+0x524/0x750 | scmi_probe+0x7fc/0x1508 | platform_probe+0xc4/0x19c | really_probe+0x32c/0x99c | __driver_probe_device+0x15c/0x3c4 | driver_probe_device+0x5c/0x170 | __driver_attach+0x1c8/0x440 | bus_for_each_dev+0xf4/0x178 | driver_attach+0x3c/0x58 | bus_add_driver+0x234/0x4d4 | driver_register+0xf4/0x3c0 | __platform_driver_register+0x60/0x88 | scmi_driver_init+0xb0/0x104 | do_one_initcall+0xb4/0x664 | kernel_init_freeable+0x3c8/0x894 | kernel_init+0x24/0x1e8 | ret_from_fork+0x10/0x20

In the Linux kernel, the following vulnerability has been resolved: ubifs: authentication: Fix use-after-free in ubifs_tnc_end_commit After an insertion in TNC, the tree might split and cause a node to change its `znode->parent`. A further deletion of other nodes in the tree (which also could free the nodes), the aforementioned node's `znode->cparent` could still point to a freed node. This `znode->cparent` may not be updated when getting nodes to commit in `ubifs_tnc_start_commit()`. This could then trigger a use-after-free when accessing the `znode->cparent` in `write_index()` in `ubifs_tnc_end_commit()`. This can be triggered by running rm -f /etc/test-file.bin dd if=/dev/urandom of=/etc/test-file.bin bs=1M count=60 conv=fsync in a loop, and with `CONFIG_UBIFS_FS_AUTHENTICATION`. KASAN then reports: BUG: KASAN: use-after-free in ubifs_tnc_end_commit+0xa5c/0x1950 Write of size 32 at addr ffffff800a3af86c by task ubifs_bgt0_20/153 Call trace: dump_backtrace+0x0/0x340 show_stack+0x18/0x24 dump_stack_lvl+0x9c/0xbc print_address_description.constprop.0+0x74/0x2b0 kasan_report+0x1d8/0x1f0 kasan_check_range+0xf8/0x1a0 memcpy+0x84/0xf4 ubifs_tnc_end_commit+0xa5c/0x1950 do_commit+0x4e0/0x1340 ubifs_bg_thread+0x234/0x2e0 kthread+0x36c/0x410 ret_from_fork+0x10/0x20 Allocated by task 401: kasan_save_stack+0x38/0x70 __kasan_kmalloc+0x8c/0xd0 __kmalloc+0x34c/0x5bc tnc_insert+0x140/0x16a4 ubifs_tnc_add+0x370/0x52c ubifs_jnl_write_data+0x5d8/0x870 do_writepage+0x36c/0x510 ubifs_writepage+0x190/0x4dc __writepage+0x58/0x154 write_cache_pages+0x394/0x830 do_writepages+0x1f0/0x5b0 filemap_fdatawrite_wbc+0x170/0x25c file_write_and_wait_range+0x140/0x190 ubifs_fsync+0xe8/0x290 vfs_fsync_range+0xc0/0x1e4 do_fsync+0x40/0x90 __arm64_sys_fsync+0x34/0x50 invoke_syscall.constprop.0+0xa8/0x260 do_el0_svc+0xc8/0x1f0 el0_svc+0x34/0x70 el0t_64_sync_handler+0x108/0x114 el0t_64_sync+0x1a4/0x1a8 Freed by task 403: kasan_save_stack+0x38/0x70 kasan_set_track+0x28/0x40 kasan_set_free_info+0x28/0x4c __kasan_slab_free+0xd4/0x13c kfree+0xc4/0x3a0 tnc_delete+0x3f4/0xe40 ubifs_tnc_remove_range+0x368/0x73c ubifs_tnc_remove_ino+0x29c/0x2e0 ubifs_jnl_delete_inode+0x150/0x260 ubifs_evict_inode+0x1d4/0x2e4 evict+0x1c8/0x450 iput+0x2a0/0x3c4 do_unlinkat+0x2cc/0x490 __arm64_sys_unlinkat+0x90/0x100 invoke_syscall.constprop.0+0xa8/0x260 do_el0_svc+0xc8/0x1f0 el0_svc+0x34/0x70 el0t_64_sync_handler+0x108/0x114 el0t_64_sync+0x1a4/0x1a8 The offending `memcpy()` in `ubifs_copy_hash()` has a use-after-free when a node becomes root in TNC but still has a `cparent` to an already freed node. More specifically, consider the following TNC: zroot / / zp1 / / zn Inserting a new node `zn_new` with a key smaller then `zn` will trigger a split in `tnc_insert()` if `zp1` is full: zroot / \ / \ zp1 zp2 / \ / \ zn_new zn `zn->parent` has now been moved to `zp2`, *but* `zn->cparent` still points to `zp1`. Now, consider a removal of all the nodes _except_ `zn`. Just when `tnc_delete()` is about to delete `zroot` and `zp2`: zroot \ \ zp2 \ \ zn `zroot` and `zp2` get freed and the tree collapses: zn `zn` now becomes the new `zroot`. `get_znodes_to_commit()` will now only find `zn`, the new `zroot`, and `write_index()` will check its `znode->cparent` that wrongly points to the already freed `zp1`. `ubifs_copy_hash()` thus gets wrongly called with `znode->cparent->zbranch[znode->iip].hash` that triggers the use-after-free! Fix this by explicitly setting `znode->cparent` to `NULL` in `get_znodes_to_commit()` for the root node. The search for the dirty nodes ---truncated---

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix race in concurrent f2fs_stop_gc_thread In my test case, concurrent calls to f2fs shutdown report the following stack trace: Oops: general protection fault, probably for non-canonical address 0xc6cfff63bb5513fc: 0000 [#1] PREEMPT SMP PTI CPU: 0 UID: 0 PID: 678 Comm: f2fs_rep_shutdo Not tainted 6.12.0-rc5-next-20241029-g6fb2fa9805c5-dirty #85 Call Trace: <TASK> ? show_regs+0x8b/0xa0 ? __die_body+0x26/0xa0 ? die_addr+0x54/0x90 ? exc_general_protection+0x24b/0x5c0 ? asm_exc_general_protection+0x26/0x30 ? kthread_stop+0x46/0x390 f2fs_stop_gc_thread+0x6c/0x110 f2fs_do_shutdown+0x309/0x3a0 f2fs_ioc_shutdown+0x150/0x1c0 __f2fs_ioctl+0xffd/0x2ac0 f2fs_ioctl+0x76/0xe0 vfs_ioctl+0x23/0x60 __x64_sys_ioctl+0xce/0xf0 x64_sys_call+0x2b1b/0x4540 do_syscall_64+0xa7/0x240 entry_SYSCALL_64_after_hwframe+0x76/0x7e The root cause is a race condition in f2fs_stop_gc_thread() called from different f2fs shutdown paths: [CPU0] [CPU1] ---------------------- ----------------------- f2fs_stop_gc_thread f2fs_stop_gc_thread gc_th = sbi->gc_thread gc_th = sbi->gc_thread kfree(gc_th) sbi->gc_thread = NULL < gc_th != NULL > kthread_stop(gc_th->f2fs_gc_task) //UAF The commit c7f114d864ac ("f2fs: fix to avoid use-after-free in f2fs_stop_gc_thread()") attempted to fix this issue by using a read semaphore to prevent races between shutdown and remount threads, but it fails to prevent all race conditions. Fix it by converting to write lock of s_umount in f2fs_do_shutdown().

In the Linux kernel, the following vulnerability has been resolved: media: s5p-jpeg: prevent buffer overflows The current logic allows word to be less than 2. If this happens, there will be buffer overflows, as reported by smatch. Add extra checks to prevent it. While here, remove an unused word = 0 assignment.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/ufence: Prefetch ufence addr to catch bogus address access_ok() only checks for addr overflow so also try to read the addr to catch invalid addr sent from userspace. (cherry picked from commit 9408c4508483ffc60811e910a93d6425b8e63928)

In the Linux kernel, the following vulnerability has been resolved: net: Only allow init netns to set default tcp cong to a restricted algo tcp_set_default_congestion_control() is netns-safe in that it writes to &net->ipv4.tcp_congestion_control, but it also sets ca->flags |= TCP_CONG_NON_RESTRICTED which is not namespaced. This has the unintended side-effect of changing the global net.ipv4.tcp_allowed_congestion_control sysctl, despite the fact that it is read-only: 97684f0970f6 ("net: Make tcp_allowed_congestion_control readonly in non-init netns") Resolve this netns "leak" by only allowing the init netns to set the default algorithm to one that is restricted. This restriction could be removed if tcp_allowed_congestion_control were namespace-ified in the future. This bug was uncovered with https://github.com/JonathonReinhart/linux-netns-sysctl-verify

In the Linux kernel, the following vulnerability has been resolved: fsnotify: Fix ordering of iput() and watched_objects decrement Ensure the superblock is kept alive until we're done with iput(). Holding a reference to an inode is not allowed unless we ensure the superblock stays alive, which fsnotify does by keeping the watched_objects count elevated, so iput() must happen before the watched_objects decrement. This can lead to a UAF of something like sb->s_fs_info in tmpfs, but the UAF is hard to hit because race orderings that oops are more likely, thanks to the CHECK_DATA_CORRUPTION() block in generic_shutdown_super(). Also, ensure that fsnotify_put_sb_watched_objects() doesn't call fsnotify_sb_watched_objects() on a superblock that may have already been freed, which would cause a UAF read of sb->s_fsnotify_info.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix warning when unbinding If there is an error during some initialization related to firmware, the buffers dp->tx_ring[i].tx_status are released. However this is released again when the device is unbinded (ath12k_pci), and we get: WARNING: CPU: 0 PID: 2098 at mm/slub.c:4689 free_large_kmalloc+0x4d/0x80 Call Trace: free_large_kmalloc ath12k_dp_free ath12k_core_deinit ath12k_pci_remove ... The issue is always reproducible from a VM because the MSI addressing initialization is failing. In order to fix the issue, just set the buffers to NULL after releasing in order to avoid the double free.

The brcmf_cfg80211_mgmt_tx function in drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c in the Linux kernel before 4.12.3 allows local users to cause a denial of service (buffer overflow and system crash) or possibly gain privileges via a crafted NL80211_CMD_FRAME Netlink packet.

drivers/media/usb/dvb-usb/dw2102.c in the Linux kernel 4.9.x and 4.10.x before 4.10.4 interacts incorrectly with the CONFIG_VMAP_STACK option, which allows local users to cause a denial of service (system crash or memory corruption) or possibly have unspecified other impact by leveraging use of more than one virtual page for a DMA scatterlist.

drivers/media/usb/dvb-usb-v2/dvb_usb_core.c in the Linux kernel 4.9.x and 4.10.x before 4.10.12 interacts incorrectly with the CONFIG_VMAP_STACK option, which allows local users to cause a denial of service (system crash or memory corruption) or possibly have unspecified other impact by leveraging use of more than one virtual page for a DMA scatterlist.

In the Linux kernel, the following vulnerability has been resolved: scsi: iscsi: Fix iscsi_task use after free Commit d39df158518c ("scsi: iscsi: Have abort handler get ref to conn") added iscsi_get_conn()/iscsi_put_conn() calls during abort handling but then also changed the handling of the case where we detect an already completed task where we now end up doing a goto to the common put/cleanup code. This results in a iscsi_task use after free, because the common cleanup code will do a put on the iscsi_task. This reverts the goto and moves the iscsi_get_conn() to after we've checked if the iscsi_task is valid.

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Skip parsing frames of type UVC_VS_UNDEFINED in uvc_parse_format This can lead to out of bounds writes since frames of this type were not taken into account when calculating the size of the frames buffer in uvc_parse_streaming.

In the Linux kernel, the following vulnerability has been resolved: sctp: fix possible UAF in sctp_v6_available() A lockdep report [1] with CONFIG_PROVE_RCU_LIST=y hints that sctp_v6_available() is calling dev_get_by_index_rcu() and ipv6_chk_addr() without holding rcu. [1] ============================= WARNING: suspicious RCU usage 6.12.0-rc5-virtme #1216 Tainted: G W ----------------------------- net/core/dev.c:876 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 1 lock held by sctp_hello/31495: #0: ffff9f1ebbdb7418 (sk_lock-AF_INET6){+.+.}-{0:0}, at: sctp_bind (./arch/x86/include/asm/jump_label.h:27 net/sctp/socket.c:315) sctp stack backtrace: CPU: 7 UID: 0 PID: 31495 Comm: sctp_hello Tainted: G W 6.12.0-rc5-virtme #1216 Tainted: [W]=WARN Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:123) lockdep_rcu_suspicious (kernel/locking/lockdep.c:6822) dev_get_by_index_rcu (net/core/dev.c:876 (discriminator 7)) sctp_v6_available (net/sctp/ipv6.c:701) sctp sctp_do_bind (net/sctp/socket.c:400 (discriminator 1)) sctp sctp_bind (net/sctp/socket.c:320) sctp inet6_bind_sk (net/ipv6/af_inet6.c:465) ? security_socket_bind (security/security.c:4581 (discriminator 1)) __sys_bind (net/socket.c:1848 net/socket.c:1869) ? do_user_addr_fault (./include/linux/rcupdate.h:347 ./include/linux/rcupdate.h:880 ./include/linux/mm.h:729 arch/x86/mm/fault.c:1340) ? do_user_addr_fault (./arch/x86/include/asm/preempt.h:84 (discriminator 13) ./include/linux/rcupdate.h:98 (discriminator 13) ./include/linux/rcupdate.h:882 (discriminator 13) ./include/linux/mm.h:729 (discriminator 13) arch/x86/mm/fault.c:1340 (discriminator 13)) __x64_sys_bind (net/socket.c:1877 (discriminator 1) net/socket.c:1875 (discriminator 1) net/socket.c:1875 (discriminator 1)) do_syscall_64 (arch/x86/entry/common.c:52 (discriminator 1) arch/x86/entry/common.c:83 (discriminator 1)) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) RIP: 0033:0x7f59b934a1e7 Code: 44 00 00 48 8b 15 39 8c 0c 00 f7 d8 64 89 02 b8 ff ff ff ff eb bd 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 b8 31 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 09 8c 0c 00 f7 d8 64 89 01 48 All code ======== 0: 44 00 00 add %r8b,(%rax) 3: 48 8b 15 39 8c 0c 00 mov 0xc8c39(%rip),%rdx # 0xc8c43 a: f7 d8 neg %eax c: 64 89 02 mov %eax,%fs:(%rdx) f: b8 ff ff ff ff mov $0xffffffff,%eax 14: eb bd jmp 0xffffffffffffffd3 16: 66 2e 0f 1f 84 00 00 cs nopw 0x0(%rax,%rax,1) 1d: 00 00 00 20: 0f 1f 00 nopl (%rax) 23: b8 31 00 00 00 mov $0x31,%eax 28: 0f 05 syscall 2a:* 48 3d 01 f0 ff ff cmp $0xfffffffffffff001,%rax <-- trapping instruction 30: 73 01 jae 0x33 32: c3 ret 33: 48 8b 0d 09 8c 0c 00 mov 0xc8c09(%rip),%rcx # 0xc8c43 3a: f7 d8 neg %eax 3c: 64 89 01 mov %eax,%fs:(%rcx) 3f: 48 rex.W Code starting with the faulting instruction =========================================== 0: 48 3d 01 f0 ff ff cmp $0xfffffffffffff001,%rax 6: 73 01 jae 0x9 8: c3 ret 9: 48 8b 0d 09 8c 0c 00 mov 0xc8c09(%rip),%rcx # 0xc8c19 10: f7 d8 neg %eax 12: 64 89 01 mov %eax,%fs:(%rcx) 15: 48 rex.W RSP: 002b:00007ffe2d0ad398 EFLAGS: 00000202 ORIG_RAX: 0000000000000031 RAX: ffffffffffffffda RBX: 00007ffe2d0ad3d0 RCX: 00007f59b934a1e7 RDX: 000000000000001c RSI: 00007ffe2d0ad3d0 RDI: 0000000000000005 RBP: 0000000000000005 R08: 1999999999999999 R09: 0000000000000000 R10: 00007f59b9253298 R11: 000000000000 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: initramfs: avoid filename buffer overrun The initramfs filename field is defined in Documentation/driver-api/early-userspace/buffer-format.rst as: 37 cpio_file := ALGN(4) + cpio_header + filename + "\0" + ALGN(4) + data ... 55 ============= ================== ========================= 56 Field name Field size Meaning 57 ============= ================== ========================= ... 70 c_namesize 8 bytes Length of filename, including final \0 When extracting an initramfs cpio archive, the kernel's do_name() path handler assumes a zero-terminated path at @collected, passing it directly to filp_open() / init_mkdir() / init_mknod(). If a specially crafted cpio entry carries a non-zero-terminated filename and is followed by uninitialized memory, then a file may be created with trailing characters that represent the uninitialized memory. The ability to create an initramfs entry would imply already having full control of the system, so the buffer overrun shouldn't be considered a security vulnerability. Append the output of the following bash script to an existing initramfs and observe any created /initramfs_test_fname_overrunAA* path. E.g. ./reproducer.sh | gzip >> /myinitramfs It's easiest to observe non-zero uninitialized memory when the output is gzipped, as it'll overflow the heap allocated @out_buf in __gunzip(), rather than the initrd_start+initrd_size block. ---- reproducer.sh ---- nilchar="A" # change to "\0" to properly zero terminate / pad magic="070701" ino=1 mode=$(( 0100777 )) uid=0 gid=0 nlink=1 mtime=1 filesize=0 devmajor=0 devminor=1 rdevmajor=0 rdevminor=0 csum=0 fname="initramfs_test_fname_overrun" namelen=$(( ${#fname} + 1 )) # plus one to account for terminator printf "%s%08x%08x%08x%08x%08x%08x%08x%08x%08x%08x%08x%08x%08x%s" \ $magic $ino $mode $uid $gid $nlink $mtime $filesize \ $devmajor $devminor $rdevmajor $rdevminor $namelen $csum $fname termpadlen=$(( 1 + ((4 - ((110 + $namelen) & 3)) % 4) )) printf "%.s${nilchar}" $(seq 1 $termpadlen) ---- reproducer.sh ---- Symlink filename fields handled in do_symlink() won't overrun past the data segment, due to the explicit zero-termination of the symlink target. Fix filename buffer overrun by aborting the initramfs FSM if any cpio entry doesn't carry a zero-terminator at the expected (name_len - 1) offset.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k: add range check for conn_rsp_epid in htc_connect_service() I found the following bug in my fuzzer: UBSAN: array-index-out-of-bounds in drivers/net/wireless/ath/ath9k/htc_hst.c:26:51 index 255 is out of range for type 'htc_endpoint [22]' CPU: 0 UID: 0 PID: 8 Comm: kworker/0:0 Not tainted 6.11.0-rc6-dirty #14 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Workqueue: events request_firmware_work_func Call Trace: <TASK> dump_stack_lvl+0x180/0x1b0 __ubsan_handle_out_of_bounds+0xd4/0x130 htc_issue_send.constprop.0+0x20c/0x230 ? _raw_spin_unlock_irqrestore+0x3c/0x70 ath9k_wmi_cmd+0x41d/0x610 ? mark_held_locks+0x9f/0xe0 ... Since this bug has been confirmed to be caused by insufficient verification of conn_rsp_epid, I think it would be appropriate to add a range check for conn_rsp_epid to htc_connect_service() to prevent the bug from occurring.

In the Linux kernel, the following vulnerability has been resolved: ALSA: 6fire: Release resources at card release The current 6fire code tries to release the resources right after the call of usb6fire_chip_abort(). But at this moment, the card object might be still in use (as we're calling snd_card_free_when_closed()). For avoid potential UAFs, move the release of resources to the card's private_free instead of the manual call of usb6fire_chip_destroy() at the USB disconnect callback.

The sg_ioctl function in drivers/scsi/sg.c in the Linux kernel through 4.10.4 allows local users to cause a denial of service (stack-based buffer overflow) or possibly have unspecified other impact via a large command size in an SG_NEXT_CMD_LEN ioctl call, leading to out-of-bounds write access in the sg_write function.

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: Fix response handling in iwl_mvm_send_recovery_cmd() 1. The size of the response packet is not validated. 2. The response buffer is not freed. Resolve these issues by switching to iwl_mvm_send_cmd_status(), which handles both size validation and frees the buffer.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Handle dml allocation failure to avoid crash [Why] In the case where a dml allocation fails for any reason, the current state's dml contexts would no longer be valid. Then subsequent calls dc_state_copy_internal would shallow copy invalid memory and if the new state was released, a double free would occur. [How] Reset dml pointers in new_state to NULL and avoid invalid pointer (cherry picked from commit bcafdc61529a48f6f06355d78eb41b3aeda5296c)

In the Linux kernel, the following vulnerability has been resolved: smb: prevent use-after-free due to open_cached_dir error paths If open_cached_dir() encounters an error parsing the lease from the server, the error handling may race with receiving a lease break, resulting in open_cached_dir() freeing the cfid while the queued work is pending. Update open_cached_dir() to drop refs rather than directly freeing the cfid. Have cached_dir_lease_break(), cfids_laundromat_worker(), and invalidate_all_cached_dirs() clear has_lease immediately while still holding cfids->cfid_list_lock, and then use this to also simplify the reference counting in cfids_laundromat_worker() and invalidate_all_cached_dirs(). Fixes this KASAN splat (which manually injects an error and lease break in open_cached_dir()): ================================================================== BUG: KASAN: slab-use-after-free in smb2_cached_lease_break+0x27/0xb0 Read of size 8 at addr ffff88811cc24c10 by task kworker/3:1/65 CPU: 3 UID: 0 PID: 65 Comm: kworker/3:1 Not tainted 6.12.0-rc6-g255cf264e6e5-dirty #87 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 11/12/2020 Workqueue: cifsiod smb2_cached_lease_break Call Trace: <TASK> dump_stack_lvl+0x77/0xb0 print_report+0xce/0x660 kasan_report+0xd3/0x110 smb2_cached_lease_break+0x27/0xb0 process_one_work+0x50a/0xc50 worker_thread+0x2ba/0x530 kthread+0x17c/0x1c0 ret_from_fork+0x34/0x60 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 2464: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 __kasan_kmalloc+0xaa/0xb0 open_cached_dir+0xa7d/0x1fb0 smb2_query_path_info+0x43c/0x6e0 cifs_get_fattr+0x346/0xf10 cifs_get_inode_info+0x157/0x210 cifs_revalidate_dentry_attr+0x2d1/0x460 cifs_getattr+0x173/0x470 vfs_statx_path+0x10f/0x160 vfs_statx+0xe9/0x150 vfs_fstatat+0x5e/0xc0 __do_sys_newfstatat+0x91/0xf0 do_syscall_64+0x95/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 2464: kasan_save_stack+0x33/0x60 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x51/0x70 kfree+0x174/0x520 open_cached_dir+0x97f/0x1fb0 smb2_query_path_info+0x43c/0x6e0 cifs_get_fattr+0x346/0xf10 cifs_get_inode_info+0x157/0x210 cifs_revalidate_dentry_attr+0x2d1/0x460 cifs_getattr+0x173/0x470 vfs_statx_path+0x10f/0x160 vfs_statx+0xe9/0x150 vfs_fstatat+0x5e/0xc0 __do_sys_newfstatat+0x91/0xf0 do_syscall_64+0x95/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e Last potentially related work creation: kasan_save_stack+0x33/0x60 __kasan_record_aux_stack+0xad/0xc0 insert_work+0x32/0x100 __queue_work+0x5c9/0x870 queue_work_on+0x82/0x90 open_cached_dir+0x1369/0x1fb0 smb2_query_path_info+0x43c/0x6e0 cifs_get_fattr+0x346/0xf10 cifs_get_inode_info+0x157/0x210 cifs_revalidate_dentry_attr+0x2d1/0x460 cifs_getattr+0x173/0x470 vfs_statx_path+0x10f/0x160 vfs_statx+0xe9/0x150 vfs_fstatat+0x5e/0xc0 __do_sys_newfstatat+0x91/0xf0 do_syscall_64+0x95/0x1a0 entry_SYSCALL_64_after_hwframe+0x76/0x7e The buggy address belongs to the object at ffff88811cc24c00 which belongs to the cache kmalloc-1k of size 1024 The buggy address is located 16 bytes inside of freed 1024-byte region [ffff88811cc24c00, ffff88811cc25000)

The xfrm_replay_verify_len function in net/xfrm/xfrm_user.c in the Linux kernel through 4.10.6 does not validate certain size data after an XFRM_MSG_NEWAE update, which allows local users to obtain root privileges or cause a denial of service (heap-based out-of-bounds access) by leveraging the CAP_NET_ADMIN capability, as demonstrated during a Pwn2Own competition at CanSecWest 2017 for the Ubuntu 16.10 linux-image-* package 4.8.0.41.52.