In the Linux kernel, the following vulnerability has been resolved: power: supply: core: Fix boundary conditions in interpolation The functions power_supply_temp2resist_simple and power_supply_ocv2cap_simple handle boundary conditions incorrectly. The change was introduced in a4585ba2050f460f749bbaf2b67bd56c41e30283 ("power: supply: core: Use library interpolation"). There are two issues: First, the lines "high = i - 1" and "high = i" in ocv2cap have the wrong order compared to temp2resist. As a consequence, ocv2cap sets high=-1 if ocv>table[0].ocv, which causes an out-of-bounds read. Second, the logic of temp2resist is also not correct. Consider the case table[] = {{20, 100}, {10, 80}, {0, 60}}. For temp=5, we expect a resistance of 70% by interpolation. However, temp2resist sets high=low=2 and returns 60.

In the Linux kernel, the following vulnerability has been resolved: be2net: Fix buffer overflow in be_get_module_eeprom be_cmd_read_port_transceiver_data assumes that it is given a buffer that is at least PAGE_DATA_LEN long, or twice that if the module supports SFF 8472. However, this is not always the case. Fix this by passing the desired offset and length to be_cmd_read_port_transceiver_data so that we only copy the bytes once.

In the Linux kernel, the following vulnerability has been resolved: NFSD: Protect against send buffer overflow in NFSv2 READDIR Restore the previous limit on the @count argument to prevent a buffer overflow attack.

In the Linux kernel, the following vulnerability has been resolved: drivers: media: dvb-frontends/rtl2830: fix an out-of-bounds write error Ensure index in rtl2830_pid_filter does not exceed 31 to prevent out-of-bounds access. dev->filters is a 32-bit value, so set_bit and clear_bit functions should only operate on indices from 0 to 31. If index is 32, it will attempt to access a non-existent 33rd bit, leading to out-of-bounds access. Change the boundary check from index > 32 to index >= 32 to resolve this issue.

In the Linux kernel, the following vulnerability has been resolved: ice: Fix memory corruption in VF driver Disable VF's RX/TX queues, when it's disabled. VF can have queues enabled, when it requests a reset. If PF driver assumes that VF is disabled, while VF still has queues configured, VF may unmap DMA resources. In such scenario device still can map packets to memory, which ends up silently corrupting it. Previously, VF driver could experience memory corruption, which lead to crash: [ 5119.170157] BUG: unable to handle kernel paging request at 00001b9780003237 [ 5119.170166] PGD 0 P4D 0 [ 5119.170173] Oops: 0002 [#1] PREEMPT_RT SMP PTI [ 5119.170181] CPU: 30 PID: 427592 Comm: kworker/u96:2 Kdump: loaded Tainted: G W I --------- - - 4.18.0-372.9.1.rt7.166.el8.x86_64 #1 [ 5119.170189] Hardware name: Dell Inc. PowerEdge R740/014X06, BIOS 2.3.10 08/15/2019 [ 5119.170193] Workqueue: iavf iavf_adminq_task [iavf] [ 5119.170219] RIP: 0010:__page_frag_cache_drain+0x5/0x30 [ 5119.170238] Code: 0f 0f b6 77 51 85 f6 74 07 31 d2 e9 05 df ff ff e9 90 fe ff ff 48 8b 05 49 db 33 01 eb b4 0f 1f 80 00 00 00 00 0f 1f 44 00 00 <f0> 29 77 34 74 01 c3 48 8b 07 f6 c4 80 74 0f 0f b6 77 51 85 f6 74 [ 5119.170244] RSP: 0018:ffffa43b0bdcfd78 EFLAGS: 00010282 [ 5119.170250] RAX: ffffffff896b3e40 RBX: ffff8fb282524000 RCX: 0000000000000002 [ 5119.170254] RDX: 0000000049000000 RSI: 0000000000000000 RDI: 00001b9780003203 [ 5119.170259] RBP: ffff8fb248217b00 R08: 0000000000000022 R09: 0000000000000009 [ 5119.170262] R10: 2b849d6300000000 R11: 0000000000000020 R12: 0000000000000000 [ 5119.170265] R13: 0000000000001000 R14: 0000000000000009 R15: 0000000000000000 [ 5119.170269] FS: 0000000000000000(0000) GS:ffff8fb1201c0000(0000) knlGS:0000000000000000 [ 5119.170274] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 5119.170279] CR2: 00001b9780003237 CR3: 00000008f3e1a003 CR4: 00000000007726e0 [ 5119.170283] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 5119.170286] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 5119.170290] PKRU: 55555554 [ 5119.170292] Call Trace: [ 5119.170298] iavf_clean_rx_ring+0xad/0x110 [iavf] [ 5119.170324] iavf_free_rx_resources+0xe/0x50 [iavf] [ 5119.170342] iavf_free_all_rx_resources.part.51+0x30/0x40 [iavf] [ 5119.170358] iavf_virtchnl_completion+0xd8a/0x15b0 [iavf] [ 5119.170377] ? iavf_clean_arq_element+0x210/0x280 [iavf] [ 5119.170397] iavf_adminq_task+0x126/0x2e0 [iavf] [ 5119.170416] process_one_work+0x18f/0x420 [ 5119.170429] worker_thread+0x30/0x370 [ 5119.170437] ? process_one_work+0x420/0x420 [ 5119.170445] kthread+0x151/0x170 [ 5119.170452] ? set_kthread_struct+0x40/0x40 [ 5119.170460] ret_from_fork+0x35/0x40 [ 5119.170477] Modules linked in: iavf sctp ip6_udp_tunnel udp_tunnel mlx4_en mlx4_core nfp tls vhost_net vhost vhost_iotlb tap tun xt_CHECKSUM ipt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink bridge stp llc rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache sunrpc intel_rapl_msr iTCO_wdt iTCO_vendor_support dell_smbios wmi_bmof dell_wmi_descriptor dcdbas kvm_intel kvm irqbypass intel_rapl_common isst_if_common skx_edac irdma nfit libnvdimm x86_pkg_temp_thermal i40e intel_powerclamp coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel ib_uverbs rapl ipmi_ssif intel_cstate intel_uncore mei_me pcspkr acpi_ipmi ib_core mei lpc_ich i2c_i801 ipmi_si ipmi_devintf wmi ipmi_msghandler acpi_power_meter xfs libcrc32c sd_mod t10_pi sg mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ice ahci drm libahci crc32c_intel libata tg3 megaraid_sas [ 5119.170613] i2c_algo_bit dm_mirror dm_region_hash dm_log dm_mod fuse [last unloaded: iavf] [ 5119.170627] CR2: 00001b9780003237

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: debug: Fix potential buffer overflow by snprintf() snprintf() returns the would-be-filled size when the string overflows the given buffer size, hence using this value may result in the buffer overflow (although it's unrealistic). This patch replaces with a safer version, scnprintf() for papering over such a potential issue.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: use hweight16 to get correct tx antenna The chainmask is u16 so using hweight8 cannot get correct tx_ant. Without this patch, the tx_ant of band 2 would be -1 and lead to the following issue: BUG: KASAN: stack-out-of-bounds in mt7996_mcu_add_sta+0x12e0/0x16e0 [mt7996e]

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix space cache corruption and potential double allocations When testing space_cache v2 on a large set of machines, we encountered a few symptoms: 1. "unable to add free space :-17" (EEXIST) errors. 2. Missing free space info items, sometimes caught with a "missing free space info for X" error. 3. Double-accounted space: ranges that were allocated in the extent tree and also marked as free in the free space tree, ranges that were marked as allocated twice in the extent tree, or ranges that were marked as free twice in the free space tree. If the latter made it onto disk, the next reboot would hit the BUG_ON() in add_new_free_space(). 4. On some hosts with no on-disk corruption or error messages, the in-memory space cache (dumped with drgn) disagreed with the free space tree. All of these symptoms have the same underlying cause: a race between caching the free space for a block group and returning free space to the in-memory space cache for pinned extents causes us to double-add a free range to the space cache. This race exists when free space is cached from the free space tree (space_cache=v2) or the extent tree (nospace_cache, or space_cache=v1 if the cache needs to be regenerated). struct btrfs_block_group::last_byte_to_unpin and struct btrfs_block_group::progress are supposed to protect against this race, but commit d0c2f4fa555e ("btrfs: make concurrent fsyncs wait less when waiting for a transaction commit") subtly broke this by allowing multiple transactions to be unpinning extents at the same time. Specifically, the race is as follows: 1. An extent is deleted from an uncached block group in transaction A. 2. btrfs_commit_transaction() is called for transaction A. 3. btrfs_run_delayed_refs() -> __btrfs_free_extent() runs the delayed ref for the deleted extent. 4. __btrfs_free_extent() -> do_free_extent_accounting() -> add_to_free_space_tree() adds the deleted extent back to the free space tree. 5. do_free_extent_accounting() -> btrfs_update_block_group() -> btrfs_cache_block_group() queues up the block group to get cached. block_group->progress is set to block_group->start. 6. btrfs_commit_transaction() for transaction A calls switch_commit_roots(). It sets block_group->last_byte_to_unpin to block_group->progress, which is block_group->start because the block group hasn't been cached yet. 7. The caching thread gets to our block group. Since the commit roots were already switched, load_free_space_tree() sees the deleted extent as free and adds it to the space cache. It finishes caching and sets block_group->progress to U64_MAX. 8. btrfs_commit_transaction() advances transaction A to TRANS_STATE_SUPER_COMMITTED. 9. fsync calls btrfs_commit_transaction() for transaction B. Since transaction A is already in TRANS_STATE_SUPER_COMMITTED and the commit is for fsync, it advances. 10. btrfs_commit_transaction() for transaction B calls switch_commit_roots(). This time, the block group has already been cached, so it sets block_group->last_byte_to_unpin to U64_MAX. 11. btrfs_commit_transaction() for transaction A calls btrfs_finish_extent_commit(), which calls unpin_extent_range() for the deleted extent. It sees last_byte_to_unpin set to U64_MAX (by transaction B!), so it adds the deleted extent to the space cache again! This explains all of our symptoms above: * If the sequence of events is exactly as described above, when the free space is re-added in step 11, it will fail with EEXIST. * If another thread reallocates the deleted extent in between steps 7 and 11, then step 11 will silently re-add that space to the space cache as free even though it is actually allocated. Then, if that space is allocated *again*, the free space tree will be corrupted (namely, the wrong item will be deleted). * If we don't catch this free space tree corr ---truncated---

track_header in libavformat/vividas.c in FFmpeg 4.3.1 has an out-of-bounds write because of incorrect extradata packing.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: Fix KASAN slab-out-of-bounds in cachefiles_set_volume_xattr Use the actual length of volume coherency data when setting the xattr to avoid the following KASAN report. BUG: KASAN: slab-out-of-bounds in cachefiles_set_volume_xattr+0xa0/0x350 [cachefiles] Write of size 4 at addr ffff888101e02af4 by task kworker/6:0/1347 CPU: 6 PID: 1347 Comm: kworker/6:0 Kdump: loaded Not tainted 5.18.0-rc1-nfs-fscache-netfs+ #13 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-4.fc34 04/01/2014 Workqueue: events fscache_create_volume_work [fscache] Call Trace: <TASK> dump_stack_lvl+0x45/0x5a print_report.cold+0x5e/0x5db ? __lock_text_start+0x8/0x8 ? cachefiles_set_volume_xattr+0xa0/0x350 [cachefiles] kasan_report+0xab/0x120 ? cachefiles_set_volume_xattr+0xa0/0x350 [cachefiles] kasan_check_range+0xf5/0x1d0 memcpy+0x39/0x60 cachefiles_set_volume_xattr+0xa0/0x350 [cachefiles] cachefiles_acquire_volume+0x2be/0x500 [cachefiles] ? __cachefiles_free_volume+0x90/0x90 [cachefiles] fscache_create_volume_work+0x68/0x160 [fscache] process_one_work+0x3b7/0x6a0 worker_thread+0x2c4/0x650 ? process_one_work+0x6a0/0x6a0 kthread+0x16c/0x1a0 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x22/0x30 </TASK> Allocated by task 1347: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x81/0xa0 cachefiles_set_volume_xattr+0x76/0x350 [cachefiles] cachefiles_acquire_volume+0x2be/0x500 [cachefiles] fscache_create_volume_work+0x68/0x160 [fscache] process_one_work+0x3b7/0x6a0 worker_thread+0x2c4/0x650 kthread+0x16c/0x1a0 ret_from_fork+0x22/0x30 The buggy address belongs to the object at ffff888101e02af0 which belongs to the cache kmalloc-8 of size 8 The buggy address is located 4 bytes inside of 8-byte region [ffff888101e02af0, ffff888101e02af8) The buggy address belongs to the physical page: page:00000000a2292d70 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x101e02 flags: 0x17ffffc0000200(slab|node=0|zone=2|lastcpupid=0x1fffff) raw: 0017ffffc0000200 0000000000000000 dead000000000001 ffff888100042280 raw: 0000000000000000 0000000080660066 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888101e02980: fc 00 fc fc fc fc 00 fc fc fc fc 00 fc fc fc fc ffff888101e02a00: 00 fc fc fc fc 00 fc fc fc fc 00 fc fc fc fc 00 >ffff888101e02a80: fc fc fc fc 00 fc fc fc fc 00 fc fc fc fc 04 fc ^ ffff888101e02b00: fc fc fc 00 fc fc fc fc 00 fc fc fc fc 00 fc fc ffff888101e02b80: fc fc 00 fc fc fc fc 00 fc fc fc fc 00 fc fc fc ==================================================================

In the Linux kernel, the following vulnerability has been resolved: vt: fix memory overlapping when deleting chars in the buffer A memory overlapping copy occurs when deleting a long line. This memory overlapping copy can cause data corruption when scr_memcpyw is optimized to memcpy because memcpy does not ensure its behavior if the destination buffer overlaps with the source buffer. The line buffer is not always broken, because the memcpy utilizes the hardware acceleration, whose result is not deterministic. Fix this problem by using replacing the scr_memcpyw with scr_memmovew.

In the Linux kernel before 6.1.3, fs/ntfs3/record.c does not validate resident attribute names. An out-of-bounds write may occur.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Avoid field-overflowing memcpy() In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally writing across neighboring fields. Use flexible arrays instead of zero-element arrays (which look like they are always overflowing) and split the cross-field memcpy() into two halves that can be appropriately bounds-checked by the compiler. We were doing: #define ETH_HLEN 14 #define VLAN_HLEN 4 ... #define MLX5E_XDP_MIN_INLINE (ETH_HLEN + VLAN_HLEN) ... struct mlx5e_tx_wqe *wqe = mlx5_wq_cyc_get_wqe(wq, pi); ... struct mlx5_wqe_eth_seg *eseg = &wqe->eth; struct mlx5_wqe_data_seg *dseg = wqe->data; ... memcpy(eseg->inline_hdr.start, xdptxd->data, MLX5E_XDP_MIN_INLINE); target is wqe->eth.inline_hdr.start (which the compiler sees as being 2 bytes in size), but copying 18, intending to write across start (really vlan_tci, 2 bytes). The remaining 16 bytes get written into wqe->data[0], covering byte_count (4 bytes), lkey (4 bytes), and addr (8 bytes). struct mlx5e_tx_wqe { struct mlx5_wqe_ctrl_seg ctrl; /* 0 16 */ struct mlx5_wqe_eth_seg eth; /* 16 16 */ struct mlx5_wqe_data_seg data[]; /* 32 0 */ /* size: 32, cachelines: 1, members: 3 */ /* last cacheline: 32 bytes */ }; struct mlx5_wqe_eth_seg { u8 swp_outer_l4_offset; /* 0 1 */ u8 swp_outer_l3_offset; /* 1 1 */ u8 swp_inner_l4_offset; /* 2 1 */ u8 swp_inner_l3_offset; /* 3 1 */ u8 cs_flags; /* 4 1 */ u8 swp_flags; /* 5 1 */ __be16 mss; /* 6 2 */ __be32 flow_table_metadata; /* 8 4 */ union { struct { __be16 sz; /* 12 2 */ u8 start[2]; /* 14 2 */ } inline_hdr; /* 12 4 */ struct { __be16 type; /* 12 2 */ __be16 vlan_tci; /* 14 2 */ } insert; /* 12 4 */ __be32 trailer; /* 12 4 */ }; /* 12 4 */ /* size: 16, cachelines: 1, members: 9 */ /* last cacheline: 16 bytes */ }; struct mlx5_wqe_data_seg { __be32 byte_count; /* 0 4 */ __be32 lkey; /* 4 4 */ __be64 addr; /* 8 8 */ /* size: 16, cachelines: 1, members: 3 */ /* last cacheline: 16 bytes */ }; So, split the memcpy() so the compiler can reason about the buffer sizes. "pahole" shows no size nor member offset changes to struct mlx5e_tx_wqe nor struct mlx5e_umr_wqe. "objdump -d" shows no meaningful object code changes (i.e. only source line number induced differences and optimizations).

In the Linux kernel, the following vulnerability has been resolved: watch_queue: Fix filter limit check In watch_queue_set_filter(), there are a couple of places where we check that the filter type value does not exceed what the type_filter bitmap can hold. One place calculates the number of bits by: if (tf[i].type >= sizeof(wfilter->type_filter) * 8) which is fine, but the second does: if (tf[i].type >= sizeof(wfilter->type_filter) * BITS_PER_LONG) which is not. This can lead to a couple of out-of-bounds writes due to a too-large type: (1) __set_bit() on wfilter->type_filter (2) Writing more elements in wfilter->filters[] than we allocated. Fix this by just using the proper WATCH_TYPE__NR instead, which is the number of types we actually know about. The bug may cause an oops looking something like: BUG: KASAN: slab-out-of-bounds in watch_queue_set_filter+0x659/0x740 Write of size 4 at addr ffff88800d2c66bc by task watch_queue_oob/611 ... Call Trace: <TASK> dump_stack_lvl+0x45/0x59 print_address_description.constprop.0+0x1f/0x150 ... kasan_report.cold+0x7f/0x11b ... watch_queue_set_filter+0x659/0x740 ... __x64_sys_ioctl+0x127/0x190 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Allocated by task 611: kasan_save_stack+0x1e/0x40 __kasan_kmalloc+0x81/0xa0 watch_queue_set_filter+0x23a/0x740 __x64_sys_ioctl+0x127/0x190 do_syscall_64+0x43/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae The buggy address belongs to the object at ffff88800d2c66a0 which belongs to the cache kmalloc-32 of size 32 The buggy address is located 28 bytes inside of 32-byte region [ffff88800d2c66a0, ffff88800d2c66c0)

In the Linux kernel, the following vulnerability has been resolved: net: usb: aqc111: Fix out-of-bounds accesses in RX fixup aqc111_rx_fixup() contains several out-of-bounds accesses that can be triggered by a malicious (or defective) USB device, in particular: - The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds, causing OOB reads and (on big-endian systems) OOB endianness flips. - A packet can overlap the metadata array, causing a later OOB endianness flip to corrupt data used by a cloned SKB that has already been handed off into the network stack. - A packet SKB can be constructed whose tail is far beyond its end, causing out-of-bounds heap data to be considered part of the SKB's data. Found doing variant analysis. Tested it with another driver (ax88179_178a), since I don't have a aqc111 device to test it, but the code looks very similar.

In the Linux kernel, the following vulnerability has been resolved: btrfs: prevent copying too big compressed lzo segment Compressed length can be corrupted to be a lot larger than memory we have allocated for buffer. This will cause memcpy in copy_compressed_segment to write outside of allocated memory. This mostly results in stuck read syscall but sometimes when using btrfs send can get #GP kernel: general protection fault, probably for non-canonical address 0x841551d5c1000: 0000 [#1] PREEMPT SMP NOPTI kernel: CPU: 17 PID: 264 Comm: kworker/u256:7 Tainted: P OE 5.17.0-rc2-1 #12 kernel: Workqueue: btrfs-endio btrfs_work_helper [btrfs] kernel: RIP: 0010:lzo_decompress_bio (./include/linux/fortify-string.h:225 fs/btrfs/lzo.c:322 fs/btrfs/lzo.c:394) btrfs Code starting with the faulting instruction =========================================== 0:* 48 8b 06 mov (%rsi),%rax <-- trapping instruction 3: 48 8d 79 08 lea 0x8(%rcx),%rdi 7: 48 83 e7 f8 and $0xfffffffffffffff8,%rdi b: 48 89 01 mov %rax,(%rcx) e: 44 89 f0 mov %r14d,%eax 11: 48 8b 54 06 f8 mov -0x8(%rsi,%rax,1),%rdx kernel: RSP: 0018:ffffb110812efd50 EFLAGS: 00010212 kernel: RAX: 0000000000001000 RBX: 000000009ca264c8 RCX: ffff98996e6d8ff8 kernel: RDX: 0000000000000064 RSI: 000841551d5c1000 RDI: ffffffff9500435d kernel: RBP: ffff989a3be856c0 R08: 0000000000000000 R09: 0000000000000000 kernel: R10: 0000000000000000 R11: 0000000000001000 R12: ffff98996e6d8000 kernel: R13: 0000000000000008 R14: 0000000000001000 R15: 000841551d5c1000 kernel: FS: 0000000000000000(0000) GS:ffff98a09d640000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 00001e9f984d9ea8 CR3: 000000014971a000 CR4: 00000000003506e0 kernel: Call Trace: kernel: <TASK> kernel: end_compressed_bio_read (fs/btrfs/compression.c:104 fs/btrfs/compression.c:1363 fs/btrfs/compression.c:323) btrfs kernel: end_workqueue_fn (fs/btrfs/disk-io.c:1923) btrfs kernel: btrfs_work_helper (fs/btrfs/async-thread.c:326) btrfs kernel: process_one_work (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:212 ./include/trace/events/workqueue.h:108 kernel/workqueue.c:2312) kernel: worker_thread (./include/linux/list.h:292 kernel/workqueue.c:2455) kernel: ? process_one_work (kernel/workqueue.c:2397) kernel: kthread (kernel/kthread.c:377) kernel: ? kthread_complete_and_exit (kernel/kthread.c:332) kernel: ret_from_fork (arch/x86/entry/entry_64.S:301) kernel: </TASK>

In the Linux kernel, the following vulnerability has been resolved: ata: sata_dwc_460ex: Fix crash due to OOB write the driver uses libata's "tag" values from in various arrays. Since the mentioned patch bumped the ATA_TAG_INTERNAL to 32, the value of the SATA_DWC_QCMD_MAX needs to account for that. Otherwise ATA_TAG_INTERNAL usage cause similar crashes like this as reported by Tice Rex on the OpenWrt Forum and reproduced (with symbols) here: | BUG: Kernel NULL pointer dereference at 0x00000000 | Faulting instruction address: 0xc03ed4b8 | Oops: Kernel access of bad area, sig: 11 [#1] | BE PAGE_SIZE=4K PowerPC 44x Platform | CPU: 0 PID: 362 Comm: scsi_eh_1 Not tainted 5.4.163 #0 | NIP: c03ed4b8 LR: c03d27e8 CTR: c03ed36c | REGS: cfa59950 TRAP: 0300 Not tainted (5.4.163) | MSR: 00021000 <CE,ME> CR: 42000222 XER: 00000000 | DEAR: 00000000 ESR: 00000000 | GPR00: c03d27e8 cfa59a08 cfa55fe0 00000000 0fa46bc0 [...] | [..] | NIP [c03ed4b8] sata_dwc_qc_issue+0x14c/0x254 | LR [c03d27e8] ata_qc_issue+0x1c8/0x2dc | Call Trace: | [cfa59a08] [c003f4e0] __cancel_work_timer+0x124/0x194 (unreliable) | [cfa59a78] [c03d27e8] ata_qc_issue+0x1c8/0x2dc | [cfa59a98] [c03d2b3c] ata_exec_internal_sg+0x240/0x524 | [cfa59b08] [c03d2e98] ata_exec_internal+0x78/0xe0 | [cfa59b58] [c03d30fc] ata_read_log_page.part.38+0x1dc/0x204 | [cfa59bc8] [c03d324c] ata_identify_page_supported+0x68/0x130 | [...] This is because sata_dwc_dma_xfer_complete() NULLs the dma_pending's next neighbour "chan" (a *dma_chan struct) in this '32' case right here (line ~735): > hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_NONE; Then the next time, a dma gets issued; dma_dwc_xfer_setup() passes the NULL'd hsdevp->chan to the dmaengine_slave_config() which then causes the crash. With this patch, SATA_DWC_QCMD_MAX is now set to ATA_MAX_QUEUE + 1. This avoids the OOB. But please note, there was a worthwhile discussion on what ATA_TAG_INTERNAL and ATA_MAX_QUEUE is. And why there should not be a "fake" 33 command-long queue size. Ideally, the dw driver should account for the ATA_TAG_INTERNAL. In Damien Le Moal's words: "... having looked at the driver, it is a bigger change than just faking a 33rd "tag" that is in fact not a command tag at all." BugLink: https://github.com/openwrt/openwrt/issues/9505

In the Linux kernel, the following vulnerability has been resolved: ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx() The bounds checks in snd_soc_put_volsw_sx() are only being applied to the first channel, meaning it is possible to write out of bounds values to the second channel in stereo controls. Add appropriate checks.

In the Linux kernel, the following vulnerability has been resolved: ALSA: oss: Fix PCM OSS buffer allocation overflow We've got syzbot reports hitting INT_MAX overflow at vmalloc() allocation that is called from snd_pcm_plug_alloc(). Although we apply the restrictions to input parameters, it's based only on the hw_params of the underlying PCM device. Since the PCM OSS layer allocates a temporary buffer for the data conversion, the size may become unexpectedly large when more channels or higher rates is given; in the reported case, it went over INT_MAX, hence it hits WARN_ON(). This patch is an attempt to avoid such an overflow and an allocation for too large buffers. First off, it adds the limit of 1MB as the upper bound for period bytes. This must be large enough for all use cases, and we really don't want to handle a larger temporary buffer than this size. The size check is performed at two places, where the original period bytes is calculated and where the plugin buffer size is calculated. In addition, the driver uses array_size() and array3_size() for multiplications to catch overflows for the converted period size and buffer bytes.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: tsc2046: fix memory corruption by preventing array overflow On one side we have indio_dev->num_channels includes all physical channels + timestamp channel. On other side we have an array allocated only for physical channels. So, fix memory corruption by ARRAY_SIZE() instead of num_channels variable. Note the first case is a cleanup rather than a fix as the software timestamp channel bit in active_scanmask is never set by the IIO core.

An issue was discovered in the Linux kernel before 6.0.11. Missing validation of IEEE80211_P2P_ATTR_OPER_CHANNEL in drivers/net/wireless/microchip/wilc1000/cfg80211.c in the WILC1000 wireless driver can trigger an out-of-bounds write when parsing the channel list attribute from Wi-Fi management frames.

An issue was discovered in the Linux kernel before 6.0.11. Missing validation of IEEE80211_P2P_ATTR_CHANNEL_LIST in drivers/net/wireless/microchip/wilc1000/cfg80211.c in the WILC1000 wireless driver can trigger a heap-based buffer overflow when parsing the operating channel attribute from Wi-Fi management frames.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing() The SJA1105 family has 45 L2 policing table entries (SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110 (SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but accounting for the difference in port count (5 in SJA1105 vs 10 in SJA1110) does not fully explain the difference. Rather, the SJA1110 also has L2 ingress policers for multicast traffic. If a packet is classified as multicast, it will be processed by the policer index 99 + SRCPORT. The sja1105_init_l2_policing() function initializes all L2 policers such that they don't interfere with normal packet reception by default. To have a common code between SJA1105 and SJA1110, the index of the multicast policer for the port is calculated because it's an index that is out of bounds for SJA1105 but in bounds for SJA1110, and a bounds check is performed. The code fails to do the proper thing when determining what to do with the multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast" index will be equal to 45, which is also equal to table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes through the check. But at the same time, SJA1105 doesn't have multicast policers. So the code programs the SHARINDX field of an out-of-bounds element in the L2 Policing table of the static config. The comparison between index 45 and 45 entries should have determined the code to not access this policer index on SJA1105, since its memory wasn't even allocated. With enough bad luck, the out-of-bounds write could even overwrite other valid kernel data, but in this case, the issue was detected using KASAN. Kernel log: sja1105 spi5.0: Probed switch chip: SJA1105Q ================================================================== BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340 Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8 ... Workqueue: events_unbound deferred_probe_work_func Call trace: ... sja1105_setup+0x1cbc/0x2340 dsa_register_switch+0x1284/0x18d0 sja1105_probe+0x748/0x840 ... Allocated by task 8: ... sja1105_setup+0x1bcc/0x2340 dsa_register_switch+0x1284/0x18d0 sja1105_probe+0x748/0x840 ...

flb_gzip_compress in flb_gzip.c in Fluent Bit before 1.6.4 has an out-of-bounds write because it does not use the correct calculation of the maximum gzip data-size expansion.

An issue was discovered in the Linux kernel before 6.0.11. Missing validation of the number of channels in drivers/net/wireless/microchip/wilc1000/cfg80211.c in the WILC1000 wireless driver can trigger a heap-based buffer overflow when copying the list of operating channels from Wi-Fi management frames.

In the Linux kernel, the following vulnerability has been resolved: ARM: 9381/1: kasan: clear stale stack poison We found below OOB crash: [ 33.452494] ================================================================== [ 33.453513] BUG: KASAN: stack-out-of-bounds in refresh_cpu_vm_stats.constprop.0+0xcc/0x2ec [ 33.454660] Write of size 164 at addr c1d03d30 by task swapper/0/0 [ 33.455515] [ 33.455767] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 6.1.25-mainline #1 [ 33.456880] Hardware name: Generic DT based system [ 33.457555] unwind_backtrace from show_stack+0x18/0x1c [ 33.458326] show_stack from dump_stack_lvl+0x40/0x4c [ 33.459072] dump_stack_lvl from print_report+0x158/0x4a4 [ 33.459863] print_report from kasan_report+0x9c/0x148 [ 33.460616] kasan_report from kasan_check_range+0x94/0x1a0 [ 33.461424] kasan_check_range from memset+0x20/0x3c [ 33.462157] memset from refresh_cpu_vm_stats.constprop.0+0xcc/0x2ec [ 33.463064] refresh_cpu_vm_stats.constprop.0 from tick_nohz_idle_stop_tick+0x180/0x53c [ 33.464181] tick_nohz_idle_stop_tick from do_idle+0x264/0x354 [ 33.465029] do_idle from cpu_startup_entry+0x20/0x24 [ 33.465769] cpu_startup_entry from rest_init+0xf0/0xf4 [ 33.466528] rest_init from arch_post_acpi_subsys_init+0x0/0x18 [ 33.467397] [ 33.467644] The buggy address belongs to stack of task swapper/0/0 [ 33.468493] and is located at offset 112 in frame: [ 33.469172] refresh_cpu_vm_stats.constprop.0+0x0/0x2ec [ 33.469917] [ 33.470165] This frame has 2 objects: [ 33.470696] [32, 76) 'global_zone_diff' [ 33.470729] [112, 276) 'global_node_diff' [ 33.471294] [ 33.472095] The buggy address belongs to the physical page: [ 33.472862] page:3cd72da8 refcount:1 mapcount:0 mapping:00000000 index:0x0 pfn:0x41d03 [ 33.473944] flags: 0x1000(reserved|zone=0) [ 33.474565] raw: 00001000 ed741470 ed741470 00000000 00000000 00000000 ffffffff 00000001 [ 33.475656] raw: 00000000 [ 33.476050] page dumped because: kasan: bad access detected [ 33.476816] [ 33.477061] Memory state around the buggy address: [ 33.477732] c1d03c00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 33.478630] c1d03c80: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 00 [ 33.479526] >c1d03d00: 00 04 f2 f2 f2 f2 00 00 00 00 00 00 f1 f1 f1 f1 [ 33.480415] ^ [ 33.481195] c1d03d80: 00 00 00 00 00 00 00 00 00 00 04 f3 f3 f3 f3 f3 [ 33.482088] c1d03e00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 [ 33.482978] ================================================================== We find the root cause of this OOB is that arm does not clear stale stack poison in the case of cpuidle. This patch refer to arch/arm64/kernel/sleep.S to resolve this issue. From cited commit [1] that explain the problem Functions which the compiler has instrumented for KASAN place poison on the stack shadow upon entry and remove this poison prior to returning. In the case of cpuidle, CPUs exit the kernel a number of levels deep in C code. Any instrumented functions on this critical path will leave portions of the stack shadow poisoned. If CPUs lose context and return to the kernel via a cold path, we restore a prior context saved in __cpu_suspend_enter are forgotten, and we never remove the poison they placed in the stack shadow area by functions calls between this and the actual exit of the kernel. Thus, (depending on stackframe layout) subsequent calls to instrumented functions may hit this stale poison, resulting in (spurious) KASAN splats to the console. To avoid this, clear any stale poison from the idle thread for a CPU prior to bringing a CPU online. From cited commit [2] Extend to check for CONFIG_KASAN_STACK [1] commit 0d97e6d8024c ("arm64: kasan: clear stale stack poison") [2] commit d56a9ef84bd0 ("kasan, arm64: unpoison stack only with CONFIG_KASAN_STACK")

A stack overflow flaw was found in the Linux kernel's SYSCTL subsystem in how a user changes certain kernel parameters and variables. This flaw allows a local user to crash or potentially escalate their privileges on the system.

Adobe Flash Player before 18.0.0.268 and 19.x and 20.x before 20.0.0.228 on Windows and OS X and before 11.2.202.554 on Linux, Adobe AIR before 20.0.0.204, Adobe AIR SDK before 20.0.0.204, and Adobe AIR SDK & Compiler before 20.0.0.204 allow attackers to execute arbitrary code or cause a denial of service (out-of-bounds read and memory corruption) via crafted MPEG-4 data, a different vulnerability than CVE-2015-8045, CVE-2015-8047, CVE-2015-8060, CVE-2015-8408, CVE-2015-8416, CVE-2015-8417, CVE-2015-8418, CVE-2015-8419, CVE-2015-8443, CVE-2015-8444, CVE-2015-8451, CVE-2015-8455, CVE-2015-8652, CVE-2015-8654, CVE-2015-8657, CVE-2015-8658, and CVE-2015-8820.

drivers/usb/mon/mon_bin.c in usbmon in the Linux kernel before 5.19.15 and 6.x before 6.0.1 allows a user-space client to corrupt the monitor's internal memory.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: uvc: use correct buffer size when parsing configfs lists This commit fixes uvc gadget support on 32-bit platforms. Commit 0df28607c5cb ("usb: gadget: uvc: Generalise helper functions for reuse") introduced a helper function __uvcg_iter_item_entries() to aid with parsing lists of items on configfs attributes stores. This function is a generalization of another very similar function, which used a stack-allocated temporary buffer of fixed size for each item in the list and used the sizeof() operator to check for potential buffer overruns. The new function was changed to allocate the now variably sized temp buffer on heap, but wasn't properly updated to also check for max buffer size using the computed size instead of sizeof() operator. As a result, the maximum item size was 7 (plus null terminator) on 64-bit platforms, and 3 on 32-bit ones. While 7 is accidentally just barely enough, 3 is definitely too small for some of UVC configfs attributes. For example, dwFrameInteval, specified in 100ns units, usually has 6-digit item values, e.g. 166666 for 60fps.

Adobe Flash Player before 18.0.0.268 and 19.x and 20.x before 20.0.0.228 on Windows and OS X and before 11.2.202.554 on Linux, Adobe AIR before 20.0.0.204, Adobe AIR SDK before 20.0.0.204, and Adobe AIR SDK & Compiler before 20.0.0.204 allow attackers to execute arbitrary code or cause a denial of service (out-of-bounds read and memory corruption) via crafted MPEG-4 data, a different vulnerability than CVE-2015-8045, CVE-2015-8047, CVE-2015-8060, CVE-2015-8408, CVE-2015-8416, CVE-2015-8417, CVE-2015-8418, CVE-2015-8419, CVE-2015-8443, CVE-2015-8444, CVE-2015-8451, CVE-2015-8455, CVE-2015-8652, CVE-2015-8656, CVE-2015-8657, CVE-2015-8658, and CVE-2015-8820.

Adobe Flash Player before 18.0.0.268 and 19.x and 20.x before 20.0.0.228 on Windows and OS X and before 11.2.202.554 on Linux, Adobe AIR before 20.0.0.204, Adobe AIR SDK before 20.0.0.204, and Adobe AIR SDK & Compiler before 20.0.0.204 allow attackers to execute arbitrary code or cause a denial of service (out-of-bounds read and memory corruption) via crafted MPEG-4 data, a different vulnerability than CVE-2015-8045, CVE-2015-8047, CVE-2015-8060, CVE-2015-8408, CVE-2015-8416, CVE-2015-8417, CVE-2015-8418, CVE-2015-8419, CVE-2015-8443, CVE-2015-8444, CVE-2015-8451, CVE-2015-8455, CVE-2015-8654, CVE-2015-8656, CVE-2015-8657, CVE-2015-8658, and CVE-2015-8820.

Adobe Flash Player versions 25.0.0.148 and earlier have an exploitable memory corruption vulnerability in the BitmapData class. Successful exploitation could lead to arbitrary code execution.

In the Linux kernel, the following vulnerability has been resolved: xsk: validate user input for XDP_{UMEM|COMPLETION}_FILL_RING syzbot reported an illegal copy in xsk_setsockopt() [1] Make sure to validate setsockopt() @optlen parameter. [1] BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline] BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline] BUG: KASAN: slab-out-of-bounds in xsk_setsockopt+0x909/0xa40 net/xdp/xsk.c:1420 Read of size 4 at addr ffff888028c6cde3 by task syz-executor.0/7549 CPU: 0 PID: 7549 Comm: syz-executor.0 Not tainted 6.8.0-syzkaller-08951-gfe46a7dd189e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114 print_address_description mm/kasan/report.c:377 [inline] print_report+0x169/0x550 mm/kasan/report.c:488 kasan_report+0x143/0x180 mm/kasan/report.c:601 copy_from_sockptr_offset include/linux/sockptr.h:49 [inline] copy_from_sockptr include/linux/sockptr.h:55 [inline] xsk_setsockopt+0x909/0xa40 net/xdp/xsk.c:1420 do_sock_setsockopt+0x3af/0x720 net/socket.c:2311 __sys_setsockopt+0x1ae/0x250 net/socket.c:2334 __do_sys_setsockopt net/socket.c:2343 [inline] __se_sys_setsockopt net/socket.c:2340 [inline] __x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340 do_syscall_64+0xfb/0x240 entry_SYSCALL_64_after_hwframe+0x6d/0x75 RIP: 0033:0x7fb40587de69 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 e1 20 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fb40665a0c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000036 RAX: ffffffffffffffda RBX: 00007fb4059abf80 RCX: 00007fb40587de69 RDX: 0000000000000005 RSI: 000000000000011b RDI: 0000000000000006 RBP: 00007fb4058ca47a R08: 0000000000000002 R09: 0000000000000000 R10: 0000000020001980 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007fb4059abf80 R15: 00007fff57ee4d08 </TASK> Allocated by task 7549: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x3f/0x80 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:370 [inline] __kasan_kmalloc+0x98/0xb0 mm/kasan/common.c:387 kasan_kmalloc include/linux/kasan.h:211 [inline] __do_kmalloc_node mm/slub.c:3966 [inline] __kmalloc+0x233/0x4a0 mm/slub.c:3979 kmalloc include/linux/slab.h:632 [inline] __cgroup_bpf_run_filter_setsockopt+0xd2f/0x1040 kernel/bpf/cgroup.c:1869 do_sock_setsockopt+0x6b4/0x720 net/socket.c:2293 __sys_setsockopt+0x1ae/0x250 net/socket.c:2334 __do_sys_setsockopt net/socket.c:2343 [inline] __se_sys_setsockopt net/socket.c:2340 [inline] __x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340 do_syscall_64+0xfb/0x240 entry_SYSCALL_64_after_hwframe+0x6d/0x75 The buggy address belongs to the object at ffff888028c6cde0 which belongs to the cache kmalloc-8 of size 8 The buggy address is located 1 bytes to the right of allocated 2-byte region [ffff888028c6cde0, ffff888028c6cde2) The buggy address belongs to the physical page: page:ffffea0000a31b00 refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff888028c6c9c0 pfn:0x28c6c anon flags: 0xfff00000000800(slab|node=0|zone=1|lastcpupid=0x7ff) page_type: 0xffffffff() raw: 00fff00000000800 ffff888014c41280 0000000000000000 dead000000000001 raw: ffff888028c6c9c0 0000000080800057 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected page_owner tracks the page as allocated page last allocated via order 0, migratetype Unmovable, gfp_mask 0x112cc0(GFP_USER|__GFP_NOWARN|__GFP_NORETRY), pid 6648, tgid 6644 (syz-executor.0), ts 133906047828, free_ts 133859922223 set_page_owner include/linux/page_owner.h:31 [inline] post_alloc_hook+0x1ea/0x210 mm/page_alloc.c:1533 prep_new_page mm/page_alloc.c: ---truncated---

In the Linux kernel, the following vulnerability has been resolved: btrfs: make sure that WRITTEN is set on all metadata blocks We previously would call btrfs_check_leaf() if we had the check integrity code enabled, which meant that we could only run the extended leaf checks if we had WRITTEN set on the header flags. This leaves a gap in our checking, because we could end up with corruption on disk where WRITTEN isn't set on the leaf, and then the extended leaf checks don't get run which we rely on to validate all of the item pointers to make sure we don't access memory outside of the extent buffer. However, since 732fab95abe2 ("btrfs: check-integrity: remove CONFIG_BTRFS_FS_CHECK_INTEGRITY option") we no longer call btrfs_check_leaf() from btrfs_mark_buffer_dirty(), which means we only ever call it on blocks that are being written out, and thus have WRITTEN set, or that are being read in, which should have WRITTEN set. Add checks to make sure we have WRITTEN set appropriately, and then make sure __btrfs_check_leaf() always does the item checking. This will protect us from file systems that have been corrupted and no longer have WRITTEN set on some of the blocks. This was hit on a crafted image tweaking the WRITTEN bit and reported by KASAN as out-of-bound access in the eb accessors. The example is a dir item at the end of an eb. [2.042] BTRFS warning (device loop1): bad eb member start: ptr 0x3fff start 30572544 member offset 16410 size 2 [2.040] general protection fault, probably for non-canonical address 0xe0009d1000000003: 0000 [#1] PREEMPT SMP KASAN NOPTI [2.537] KASAN: maybe wild-memory-access in range [0x0005088000000018-0x000508800000001f] [2.729] CPU: 0 PID: 2587 Comm: mount Not tainted 6.8.2 #1 [2.729] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 [2.621] RIP: 0010:btrfs_get_16+0x34b/0x6d0 [2.621] RSP: 0018:ffff88810871fab8 EFLAGS: 00000206 [2.621] RAX: 0000a11000000003 RBX: ffff888104ff8720 RCX: ffff88811b2288c0 [2.621] RDX: dffffc0000000000 RSI: ffffffff81dd8aca RDI: ffff88810871f748 [2.621] RBP: 000000000000401a R08: 0000000000000001 R09: ffffed10210e3ee9 [2.621] R10: ffff88810871f74f R11: 205d323430333737 R12: 000000000000001a [2.621] R13: 000508800000001a R14: 1ffff110210e3f5d R15: ffffffff850011e8 [2.621] FS: 00007f56ea275840(0000) GS:ffff88811b200000(0000) knlGS:0000000000000000 [2.621] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [2.621] CR2: 00007febd13b75c0 CR3: 000000010bb50000 CR4: 00000000000006f0 [2.621] Call Trace: [2.621] <TASK> [2.621] ? show_regs+0x74/0x80 [2.621] ? die_addr+0x46/0xc0 [2.621] ? exc_general_protection+0x161/0x2a0 [2.621] ? asm_exc_general_protection+0x26/0x30 [2.621] ? btrfs_get_16+0x33a/0x6d0 [2.621] ? btrfs_get_16+0x34b/0x6d0 [2.621] ? btrfs_get_16+0x33a/0x6d0 [2.621] ? __pfx_btrfs_get_16+0x10/0x10 [2.621] ? __pfx_mutex_unlock+0x10/0x10 [2.621] btrfs_match_dir_item_name+0x101/0x1a0 [2.621] btrfs_lookup_dir_item+0x1f3/0x280 [2.621] ? __pfx_btrfs_lookup_dir_item+0x10/0x10 [2.621] btrfs_get_tree+0xd25/0x1910 [ copy more details from report ]

In the Linux kernel, the following vulnerability has been resolved: ice: fix memory corruption bug with suspend and rebuild The ice driver would previously panic after suspend. This is caused from the driver *only* calling the ice_vsi_free_q_vectors() function by itself, when it is suspending. Since commit b3e7b3a6ee92 ("ice: prevent NULL pointer deref during reload") the driver has zeroed out num_q_vectors, and only restored it in ice_vsi_cfg_def(). This further causes the ice_rebuild() function to allocate a zero length buffer, after which num_q_vectors is updated, and then the new value of num_q_vectors is used to index into the zero length buffer, which corrupts memory. The fix entails making sure all the code referencing num_q_vectors only does so after it has been reset via ice_vsi_cfg_def(). I didn't perform a full bisect, but I was able to test against 6.1.77 kernel and that ice driver works fine for suspend/resume with no panic, so sometime since then, this problem was introduced. Also clean up an un-needed init of a local variable in the function being modified. PANIC from 6.8.0-rc1: [1026674.915596] PM: suspend exit [1026675.664697] ice 0000:17:00.1: PTP reset successful [1026675.664707] ice 0000:17:00.1: 2755 msecs passed between update to cached PHC time [1026675.667660] ice 0000:b1:00.0: PTP reset successful [1026675.675944] ice 0000:b1:00.0: 2832 msecs passed between update to cached PHC time [1026677.137733] ixgbe 0000:31:00.0 ens787: NIC Link is Up 1 Gbps, Flow Control: None [1026677.190201] BUG: kernel NULL pointer dereference, address: 0000000000000010 [1026677.192753] ice 0000:17:00.0: PTP reset successful [1026677.192764] ice 0000:17:00.0: 4548 msecs passed between update to cached PHC time [1026677.197928] #PF: supervisor read access in kernel mode [1026677.197933] #PF: error_code(0x0000) - not-present page [1026677.197937] PGD 1557a7067 P4D 0 [1026677.212133] ice 0000:b1:00.1: PTP reset successful [1026677.212143] ice 0000:b1:00.1: 4344 msecs passed between update to cached PHC time [1026677.212575] [1026677.243142] Oops: 0000 [#1] PREEMPT SMP NOPTI [1026677.247918] CPU: 23 PID: 42790 Comm: kworker/23:0 Kdump: loaded Tainted: G W 6.8.0-rc1+ #1 [1026677.257989] Hardware name: Intel Corporation M50CYP2SBSTD/M50CYP2SBSTD, BIOS SE5C620.86B.01.01.0005.2202160810 02/16/2022 [1026677.269367] Workqueue: ice ice_service_task [ice] [1026677.274592] RIP: 0010:ice_vsi_rebuild_set_coalesce+0x130/0x1e0 [ice] [1026677.281421] Code: 0f 84 3a ff ff ff 41 0f b7 74 ec 02 66 89 b0 22 02 00 00 81 e6 ff 1f 00 00 e8 ec fd ff ff e9 35 ff ff ff 48 8b 43 30 49 63 ed <41> 0f b7 34 24 41 83 c5 01 48 8b 3c e8 66 89 b7 aa 02 00 00 81 e6 [1026677.300877] RSP: 0018:ff3be62a6399bcc0 EFLAGS: 00010202 [1026677.306556] RAX: ff28691e28980828 RBX: ff28691e41099828 RCX: 0000000000188000 [1026677.314148] RDX: 0000000000000000 RSI: 0000000000000010 RDI: ff28691e41099828 [1026677.321730] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 [1026677.329311] R10: 0000000000000007 R11: ffffffffffffffc0 R12: 0000000000000010 [1026677.336896] R13: 0000000000000000 R14: 0000000000000000 R15: ff28691e0eaa81a0 [1026677.344472] FS: 0000000000000000(0000) GS:ff28693cbffc0000(0000) knlGS:0000000000000000 [1026677.353000] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [1026677.359195] CR2: 0000000000000010 CR3: 0000000128df4001 CR4: 0000000000771ef0 [1026677.366779] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [1026677.374369] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [1026677.381952] PKRU: 55555554 [1026677.385116] Call Trace: [1026677.388023] <TASK> [1026677.390589] ? __die+0x20/0x70 [1026677.394105] ? page_fault_oops+0x82/0x160 [1026677.398576] ? do_user_addr_fault+0x65/0x6a0 [1026677.403307] ? exc_page_fault+0x6a/0x150 [1026677.407694] ? asm_exc_page_fault+0x22/0x30 [1026677.412349] ? ice_vsi_rebuild_set_coalesce+0x130/0x1e0 [ice] [1026677.4186 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: mm: cachestat: fix two shmem bugs When cachestat on shmem races with swapping and invalidation, there are two possible bugs: 1) A swapin error can have resulted in a poisoned swap entry in the shmem inode's xarray. Calling get_shadow_from_swap_cache() on it will result in an out-of-bounds access to swapper_spaces[]. Validate the entry with non_swap_entry() before going further. 2) When we find a valid swap entry in the shmem's inode, the shadow entry in the swapcache might not exist yet: swap IO is still in progress and we're before __remove_mapping; swapin, invalidation, or swapoff have removed the shadow from swapcache after we saw the shmem swap entry. This will send a NULL to workingset_test_recent(). The latter purely operates on pointer bits, so it won't crash - node 0, memcg ID 0, eviction timestamp 0, etc. are all valid inputs - but it's a bogus test. In theory that could result in a false "recently evicted" count. Such a false positive wouldn't be the end of the world. But for code clarity and (future) robustness, be explicit about this case. Bail on get_shadow_from_swap_cache() returning NULL.

In the Linux kernel, the following vulnerability has been resolved: nouveau/uvmm: fix addr/range calcs for remap operations dEQP-VK.sparse_resources.image_rebind.2d_array.r64i.128_128_8 was causing a remap operation like the below. op_remap: prev: 0000003fffed0000 00000000000f0000 00000000a5abd18a 0000000000000000 op_remap: next: op_remap: unmap: 0000003fffed0000 0000000000100000 0 op_map: map: 0000003ffffc0000 0000000000010000 000000005b1ba33c 00000000000e0000 This was resulting in an unmap operation from 0x3fffed0000+0xf0000, 0x100000 which was corrupting the pagetables and oopsing the kernel. Fixes the prev + unmap range calcs to use start/end and map back to addr/range.

Adobe Flash Player before 18.0.0.268 and 19.x and 20.x before 20.0.0.228 on Windows and OS X and before 11.2.202.554 on Linux, Adobe AIR before 20.0.0.204, Adobe AIR SDK before 20.0.0.204, and Adobe AIR SDK & Compiler before 20.0.0.204 allow attackers to execute arbitrary code or cause a denial of service (uninitialized pointer dereference and memory corruption) via crafted MPEG-4 data, a different vulnerability than CVE-2015-8045, CVE-2015-8047, CVE-2015-8060, CVE-2015-8408, CVE-2015-8416, CVE-2015-8417, CVE-2015-8418, CVE-2015-8419, CVE-2015-8443, CVE-2015-8444, CVE-2015-8451, CVE-2015-8455, CVE-2015-8652, CVE-2015-8654, CVE-2015-8656, CVE-2015-8657, and CVE-2015-8820.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/pm: Vangogh: Fix kernel memory out of bounds write KASAN reports that the GPU metrics table allocated in vangogh_tables_init() is not large enough for the memset done in smu_cmn_init_soft_gpu_metrics(). Condensed report follows: [ 33.861314] BUG: KASAN: slab-out-of-bounds in smu_cmn_init_soft_gpu_metrics+0x73/0x200 [amdgpu] [ 33.861799] Write of size 168 at addr ffff888129f59500 by task mangoapp/1067 ... [ 33.861808] CPU: 6 UID: 1000 PID: 1067 Comm: mangoapp Tainted: G W 6.12.0-rc4 #356 1a56f59a8b5182eeaf67eb7cb8b13594dd23b544 [ 33.861816] Tainted: [W]=WARN [ 33.861818] Hardware name: Valve Galileo/Galileo, BIOS F7G0107 12/01/2023 [ 33.861822] Call Trace: [ 33.861826] <TASK> [ 33.861829] dump_stack_lvl+0x66/0x90 [ 33.861838] print_report+0xce/0x620 [ 33.861853] kasan_report+0xda/0x110 [ 33.862794] kasan_check_range+0xfd/0x1a0 [ 33.862799] __asan_memset+0x23/0x40 [ 33.862803] smu_cmn_init_soft_gpu_metrics+0x73/0x200 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.863306] vangogh_get_gpu_metrics_v2_4+0x123/0xad0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.864257] vangogh_common_get_gpu_metrics+0xb0c/0xbc0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.865682] amdgpu_dpm_get_gpu_metrics+0xcc/0x110 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.866160] amdgpu_get_gpu_metrics+0x154/0x2d0 [amdgpu 13b1bc364ec578808f676eba412c20eaab792779] [ 33.867135] dev_attr_show+0x43/0xc0 [ 33.867147] sysfs_kf_seq_show+0x1f1/0x3b0 [ 33.867155] seq_read_iter+0x3f8/0x1140 [ 33.867173] vfs_read+0x76c/0xc50 [ 33.867198] ksys_read+0xfb/0x1d0 [ 33.867214] do_syscall_64+0x90/0x160 ... [ 33.867353] Allocated by task 378 on cpu 7 at 22.794876s: [ 33.867358] kasan_save_stack+0x33/0x50 [ 33.867364] kasan_save_track+0x17/0x60 [ 33.867367] __kasan_kmalloc+0x87/0x90 [ 33.867371] vangogh_init_smc_tables+0x3f9/0x840 [amdgpu] [ 33.867835] smu_sw_init+0xa32/0x1850 [amdgpu] [ 33.868299] amdgpu_device_init+0x467b/0x8d90 [amdgpu] [ 33.868733] amdgpu_driver_load_kms+0x19/0xf0 [amdgpu] [ 33.869167] amdgpu_pci_probe+0x2d6/0xcd0 [amdgpu] [ 33.869608] local_pci_probe+0xda/0x180 [ 33.869614] pci_device_probe+0x43f/0x6b0 Empirically we can confirm that the former allocates 152 bytes for the table, while the latter memsets the 168 large block. Root cause appears that when GPU metrics tables for v2_4 parts were added it was not considered to enlarge the table to fit. The fix in this patch is rather "brute force" and perhaps later should be done in a smarter way, by extracting and consolidating the part version to size logic to a common helper, instead of brute forcing the largest possible allocation. Nevertheless, for now this works and fixes the out of bounds write. v2: * Drop impossible v3_0 case. (Mario) (cherry picked from commit 0880f58f9609f0200483a49429af0f050d281703)

In the Linux kernel, the following vulnerability has been resolved: ext4: fix error handling in ext4_fc_record_modified_inode() Current code does not fully takes care of krealloc() error case, which could lead to silent memory corruption or a kernel bug. This patch fixes that. Also it cleans up some duplicated error handling logic from various functions in fast_commit.c file.

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays The frequency table arrays are supposed to be terminated with an empty element. Add such entry to the end of the arrays where it is missing in order to avoid possible out-of-bound access when the table is traversed by functions like qcom_find_freq() or qcom_find_freq_floor(). Only compile tested.

In the Linux kernel, the following vulnerability has been resolved: igc: avoid returning frame twice in XDP_REDIRECT When a frame can not be transmitted in XDP_REDIRECT (e.g. due to a full queue), it is necessary to free it by calling xdp_return_frame_rx_napi. However, this is the responsibility of the caller of the ndo_xdp_xmit (see for example bq_xmit_all in kernel/bpf/devmap.c) and thus calling it inside igc_xdp_xmit (which is the ndo_xdp_xmit of the igc driver) as well will lead to memory corruption. In fact, bq_xmit_all expects that it can return all frames after the last successfully transmitted one. Therefore, break for the first not transmitted frame, but do not call xdp_return_frame_rx_napi in igc_xdp_xmit. This is equally implemented in other Intel drivers such as the igb. There are two alternatives to this that were rejected: 1. Return num_frames as all the frames would have been transmitted and release them inside igc_xdp_xmit. While it might work technically, it is not what the return value is meant to represent (i.e. the number of SUCCESSFULLY transmitted packets). 2. Rework kernel/bpf/devmap.c and all drivers to support non-consecutively dropped packets. Besides being complex, it likely has a negative performance impact without a significant gain since it is anyway unlikely that the next frame can be transmitted if the previous one was dropped. The memory corruption can be reproduced with the following script which leads to a kernel panic after a few seconds. It basically generates more traffic than a i225 NIC can transmit and pushes it via XDP_REDIRECT from a virtual interface to the physical interface where frames get dropped. #!/bin/bash INTERFACE=enp4s0 INTERFACE_IDX=`cat /sys/class/net/$INTERFACE/ifindex` sudo ip link add dev veth1 type veth peer name veth2 sudo ip link set up $INTERFACE sudo ip link set up veth1 sudo ip link set up veth2 cat << EOF > redirect.bpf.c SEC("prog") int redirect(struct xdp_md *ctx) { return bpf_redirect($INTERFACE_IDX, 0); } char _license[] SEC("license") = "GPL"; EOF clang -O2 -g -Wall -target bpf -c redirect.bpf.c -o redirect.bpf.o sudo ip link set veth2 xdp obj redirect.bpf.o cat << EOF > pass.bpf.c SEC("prog") int pass(struct xdp_md *ctx) { return XDP_PASS; } char _license[] SEC("license") = "GPL"; EOF clang -O2 -g -Wall -target bpf -c pass.bpf.c -o pass.bpf.o sudo ip link set $INTERFACE xdp obj pass.bpf.o cat << EOF > trafgen.cfg { /* Ethernet Header */ 0xe8, 0x6a, 0x64, 0x41, 0xbf, 0x46, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, const16(ETH_P_IP), /* IPv4 Header */ 0b01000101, 0, # IPv4 version, IHL, TOS const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header)) const16(2), # IPv4 ident 0b01000000, 0, # IPv4 flags, fragmentation off 64, # IPv4 TTL 17, # Protocol UDP csumip(14, 33), # IPv4 checksum /* UDP Header */ 10, 0, 1, 1, # IP Src - adapt as needed 10, 0, 1, 2, # IP Dest - adapt as needed const16(6666), # UDP Src Port const16(6666), # UDP Dest Port const16(1008), # UDP length (UDP header 8 bytes + payload length) csumudp(14, 34), # UDP checksum /* Payload */ fill('W', 1000), } EOF sudo trafgen -i trafgen.cfg -b3000MB -o veth1 --cpp

In the Linux kernel, the following vulnerability has been resolved: libbpf: Use OPTS_SET() macro in bpf_xdp_query() When the feature_flags and xdp_zc_max_segs fields were added to the libbpf bpf_xdp_query_opts, the code writing them did not use the OPTS_SET() macro. This causes libbpf to write to those fields unconditionally, which means that programs compiled against an older version of libbpf (with a smaller size of the bpf_xdp_query_opts struct) will have its stack corrupted by libbpf writing out of bounds. The patch adding the feature_flags field has an early bail out if the feature_flags field is not part of the opts struct (via the OPTS_HAS) macro, but the patch adding xdp_zc_max_segs does not. For consistency, this fix just changes the assignments to both fields to use the OPTS_SET() macro.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Stop parsing channels bits when all channels are found. If a usb audio device sets more bits than the amount of channels it could write outside of the map array.

In the Linux kernel, the following vulnerability has been resolved: Both cadence-quadspi ->runtime_suspend() and ->runtime_resume() implementations start with: struct cqspi_st *cqspi = dev_get_drvdata(dev); struct spi_controller *host = dev_get_drvdata(dev); This obviously cannot be correct, unless "struct cqspi_st" is the first member of " struct spi_controller", or the other way around, but it is not the case. "struct spi_controller" is allocated by devm_spi_alloc_host(), which allocates an extra amount of memory for private data, used to store "struct cqspi_st". The ->probe() function of the cadence-quadspi driver then sets the device drvdata to store the address of the "struct cqspi_st" structure. Therefore: struct cqspi_st *cqspi = dev_get_drvdata(dev); is correct, but: struct spi_controller *host = dev_get_drvdata(dev); is not, as it makes "host" point not to a "struct spi_controller" but to the same "struct cqspi_st" structure as above. This obviously leads to bad things (memory corruption, kernel crashes) directly during ->probe(), as ->probe() enables the device using PM runtime, leading the ->runtime_resume() hook being called, which in turns calls spi_controller_resume() with the wrong pointer. This has at least been reported [0] to cause a kernel crash, but the exact behavior will depend on the memory contents. [0] https://lore.kernel.org/all/20240226121803.5a7r5wkpbbowcxgx@dhruva/ This issue potentially affects all platforms that are currently using the cadence-quadspi driver.

In the Linux kernel, the following vulnerability has been resolved: efi: runtime: Fix potential overflow of soft-reserved region size md_size will have been narrowed if we have >= 4GB worth of pages in a soft-reserved region.

In the Linux kernel, the following vulnerability has been resolved: s390/vfio-ap: always filter entire AP matrix The vfio_ap_mdev_filter_matrix function is called whenever a new adapter or domain is assigned to the mdev. The purpose of the function is to update the guest's AP configuration by filtering the matrix of adapters and domains assigned to the mdev. When an adapter or domain is assigned, only the APQNs associated with the APID of the new adapter or APQI of the new domain are inspected. If an APQN does not reference a queue device bound to the vfio_ap device driver, then it's APID will be filtered from the mdev's matrix when updating the guest's AP configuration. Inspecting only the APID of the new adapter or APQI of the new domain will result in passing AP queues through to a guest that are not bound to the vfio_ap device driver under certain circumstances. Consider the following: guest's AP configuration (all also assigned to the mdev's matrix): 14.0004 14.0005 14.0006 16.0004 16.0005 16.0006 unassign domain 4 unbind queue 16.0005 assign domain 4 When domain 4 is re-assigned, since only domain 4 will be inspected, the APQNs that will be examined will be: 14.0004 16.0004 Since both of those APQNs reference queue devices that are bound to the vfio_ap device driver, nothing will get filtered from the mdev's matrix when updating the guest's AP configuration. Consequently, queue 16.0005 will get passed through despite not being bound to the driver. This violates the linux device model requirement that a guest shall only be given access to devices bound to the device driver facilitating their pass-through. To resolve this problem, every adapter and domain assigned to the mdev will be inspected when filtering the mdev's matrix.

In the Linux kernel, the following vulnerability has been resolved: afs: Increase buffer size in afs_update_volume_status() The max length of volume->vid value is 20 characters. So increase idbuf[] size up to 24 to avoid overflow. Found by Linux Verification Center (linuxtesting.org) with SVACE. [DH: Actually, it's 20 + NUL, so increase it to 24 and use snprintf()]