In the Linux kernel, the following vulnerability has been resolved: iio: adc: ad7173: fix channels index for syscalib_mode Fix the index used to look up the channel when accessing the syscalib_mode attribute. The address field is a 0-based index (same as scan_index) that it used to access the channel in the ad7173_channels array throughout the driver. The channels field, on the other hand, may not match the address field depending on the channel configuration specified in the device tree and could result in an out-of-bounds access.

In the Linux kernel, the following vulnerability has been resolved: tls: handle data disappearing from under the TLS ULP TLS expects that it owns the receive queue of the TCP socket. This cannot be guaranteed in case the reader of the TCP socket entered before the TLS ULP was installed, or uses some non-standard read API (eg. zerocopy ones). Replace the WARN_ON() and a buggy early exit (which leaves anchor pointing to a freed skb) with real error handling. Wipe the parsing state and tell the reader to retry. We already reload the anchor every time we (re)acquire the socket lock, so the only condition we need to avoid is an out of bounds read (not having enough bytes in the socket for previously parsed record len). If some data was read from under TLS but there's enough in the queue we'll reload and decrypt what is most likely not a valid TLS record. Leading to some undefined behavior from TLS perspective (corrupting a stream? missing an alert? missing an attack?) but no kernel crash should take place.

In the Linux kernel, the following vulnerability has been resolved: comedi: das16m1: Fix bit shift out of bounds When checking for a supported IRQ number, the following test is used: /* only irqs 2, 3, 4, 5, 6, 7, 10, 11, 12, 14, and 15 are valid */ if ((1 << it->options[1]) & 0xdcfc) { However, `it->options[i]` is an unchecked `int` value from userspace, so the shift amount could be negative or out of bounds. Fix the test by requiring `it->options[1]` to be within bounds before proceeding with the original test.

In the Linux kernel, the following vulnerability has been resolved: md/raid1: Fix stack memory use after return in raid1_reshape In the raid1_reshape function, newpool is allocated on the stack and assigned to conf->r1bio_pool. This results in conf->r1bio_pool.wait.head pointing to a stack address. Accessing this address later can lead to a kernel panic. Example access path: raid1_reshape() { // newpool is on the stack mempool_t newpool, oldpool; // initialize newpool.wait.head to stack address mempool_init(&newpool, ...); conf->r1bio_pool = newpool; } raid1_read_request() or raid1_write_request() { alloc_r1bio() { mempool_alloc() { // if pool->alloc fails remove_element() { --pool->curr_nr; } } } } mempool_free() { if (pool->curr_nr < pool->min_nr) { // pool->wait.head is a stack address // wake_up() will try to access this invalid address // which leads to a kernel panic return; wake_up(&pool->wait); } } Fix: reinit conf->r1bio_pool.wait after assigning newpool.

In the Linux kernel, the following vulnerability has been resolved: HID: multitouch: fix slab out-of-bounds access in mt_report_fixup() A malicious HID device can trigger a slab out-of-bounds during mt_report_fixup() by passing in report descriptor smaller than 607 bytes. mt_report_fixup() attempts to patch byte offset 607 of the descriptor with 0x25 by first checking if byte offset 607 is 0x15 however it lacks bounds checks to verify if the descriptor is big enough before conducting this check. Fix this bug by ensuring the descriptor size is at least 608 bytes before accessing it. Below is the KASAN splat after the out of bounds access happens: [ 13.671954] ================================================================== [ 13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110 [ 13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10 [ 13.673297] [ 13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3 [ 13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04 [ 13.673297] Call Trace: [ 13.673297] <TASK> [ 13.673297] dump_stack_lvl+0x5f/0x80 [ 13.673297] print_report+0xd1/0x660 [ 13.673297] kasan_report+0xe5/0x120 [ 13.673297] __asan_report_load1_noabort+0x18/0x20 [ 13.673297] mt_report_fixup+0x103/0x110 [ 13.673297] hid_open_report+0x1ef/0x810 [ 13.673297] mt_probe+0x422/0x960 [ 13.673297] hid_device_probe+0x2e2/0x6f0 [ 13.673297] really_probe+0x1c6/0x6b0 [ 13.673297] __driver_probe_device+0x24f/0x310 [ 13.673297] driver_probe_device+0x4e/0x220 [ 13.673297] __device_attach_driver+0x169/0x320 [ 13.673297] bus_for_each_drv+0x11d/0x1b0 [ 13.673297] __device_attach+0x1b8/0x3e0 [ 13.673297] device_initial_probe+0x12/0x20 [ 13.673297] bus_probe_device+0x13d/0x180 [ 13.673297] device_add+0xe3a/0x1670 [ 13.673297] hid_add_device+0x31d/0xa40 [...]

In the Linux kernel, the following vulnerability has been resolved: tracing: Limit access to parser->buffer when trace_get_user failed When the length of the string written to set_ftrace_filter exceeds FTRACE_BUFF_MAX, the following KASAN alarm will be triggered: BUG: KASAN: slab-out-of-bounds in strsep+0x18c/0x1b0 Read of size 1 at addr ffff0000d00bd5ba by task ash/165 CPU: 1 UID: 0 PID: 165 Comm: ash Not tainted 6.16.0-g6bcdbd62bd56-dirty Hardware name: linux,dummy-virt (DT) Call trace: show_stack+0x34/0x50 (C) dump_stack_lvl+0xa0/0x158 print_address_description.constprop.0+0x88/0x398 print_report+0xb0/0x280 kasan_report+0xa4/0xf0 __asan_report_load1_noabort+0x20/0x30 strsep+0x18c/0x1b0 ftrace_process_regex.isra.0+0x100/0x2d8 ftrace_regex_release+0x484/0x618 __fput+0x364/0xa58 ____fput+0x28/0x40 task_work_run+0x154/0x278 do_notify_resume+0x1f0/0x220 el0_svc+0xec/0xf0 el0t_64_sync_handler+0xa0/0xe8 el0t_64_sync+0x1ac/0x1b0 The reason is that trace_get_user will fail when processing a string longer than FTRACE_BUFF_MAX, but not set the end of parser->buffer to 0. Then an OOB access will be triggered in ftrace_regex_release-> ftrace_process_regex->strsep->strpbrk. We can solve this problem by limiting access to parser->buffer when trace_get_user failed.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid out-of-bounds access in f2fs_truncate_inode_blocks() syzbot reports an UBSAN issue as below: ------------[ cut here ]------------ UBSAN: array-index-out-of-bounds in fs/f2fs/node.h:381:10 index 18446744073709550692 is out of range for type '__le32[5]' (aka 'unsigned int[5]') CPU: 0 UID: 0 PID: 5318 Comm: syz.0.0 Not tainted 6.14.0-rc3-syzkaller-00060-g6537cfb395f3 #0 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 ubsan_epilogue lib/ubsan.c:231 [inline] __ubsan_handle_out_of_bounds+0x121/0x150 lib/ubsan.c:429 get_nid fs/f2fs/node.h:381 [inline] f2fs_truncate_inode_blocks+0xa5e/0xf60 fs/f2fs/node.c:1181 f2fs_do_truncate_blocks+0x782/0x1030 fs/f2fs/file.c:808 f2fs_truncate_blocks+0x10d/0x300 fs/f2fs/file.c:836 f2fs_truncate+0x417/0x720 fs/f2fs/file.c:886 f2fs_file_write_iter+0x1bdb/0x2550 fs/f2fs/file.c:5093 aio_write+0x56b/0x7c0 fs/aio.c:1633 io_submit_one+0x8a7/0x18a0 fs/aio.c:2052 __do_sys_io_submit fs/aio.c:2111 [inline] __se_sys_io_submit+0x171/0x2e0 fs/aio.c:2081 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f238798cde9 index 18446744073709550692 (decimal, unsigned long long) = 0xfffffffffffffc64 (hexadecimal, unsigned long long) = -924 (decimal, long long) In f2fs_truncate_inode_blocks(), UBSAN detects that get_nid() tries to access .i_nid[-924], it means both offset[0] and level should zero. The possible case should be in f2fs_do_truncate_blocks(), we try to truncate inode size to zero, however, dn.ofs_in_node is zero and dn.node_page is not an inode page, so it fails to truncate inode page, and then pass zeroed free_from to f2fs_truncate_inode_blocks(), result in this issue. if (dn.ofs_in_node || IS_INODE(dn.node_page)) { f2fs_truncate_data_blocks_range(&dn, count); free_from += count; } I guess the reason why dn.node_page is not an inode page could be: there are multiple nat entries share the same node block address, once the node block address was reused, f2fs_get_node_page() may load a non-inode block. Let's add a sanity check for such condition to avoid out-of-bounds access issue.

In the Linux kernel, the following vulnerability has been resolved: software node: Correct a OOB check in software_node_get_reference_args() software_node_get_reference_args() wants to get @index-th element, so the property value requires at least '(index + 1) * sizeof(*ref)' bytes but that can not be guaranteed by current OOB check, and may cause OOB for malformed property. Fix by using as OOB check '((index + 1) * sizeof(*ref) > prop->length)'.

In the Linux kernel, the following vulnerability has been resolved: net: ppp: Add bound checking for skb data on ppp_sync_txmung Ensure we have enough data in linear buffer from skb before accessing initial bytes. This prevents potential out-of-bounds accesses when processing short packets. When ppp_sync_txmung receives an incoming package with an empty payload: (remote) gef➤ p *(struct pppoe_hdr *) (skb->head + skb->network_header) $18 = { type = 0x1, ver = 0x1, code = 0x0, sid = 0x2, length = 0x0, tag = 0xffff8880371cdb96 } from the skb struct (trimmed) tail = 0x16, end = 0x140, head = 0xffff88803346f400 "4", data = 0xffff88803346f416 ":\377", truesize = 0x380, len = 0x0, data_len = 0x0, mac_len = 0xe, hdr_len = 0x0, it is not safe to access data[2]. [pabeni@redhat.com: fixed subj typo]

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix out-of-bounds read in snd_usb_get_audioformat_uac3() In snd_usb_get_audioformat_uac3(), the length value returned from snd_usb_ctl_msg() is used directly for memory allocation without validation. This length is controlled by the USB device. The allocated buffer is cast to a uac3_cluster_header_descriptor and its fields are accessed without verifying that the buffer is large enough. If the device returns a smaller than expected length, this leads to an out-of-bounds read. Add a length check to ensure the buffer is large enough for uac3_cluster_header_descriptor.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: altmodes/displayport: do not index invalid pin_assignments A poorly implemented DisplayPort Alt Mode port partner can indicate that its pin assignment capabilities are greater than the maximum value, DP_PIN_ASSIGN_F. In this case, calls to pin_assignment_show will cause a BRK exception due to an out of bounds array access. Prevent for loop in pin_assignment_show from accessing invalid values in pin_assignments by adding DP_PIN_ASSIGN_MAX value in typec_dp.h and using i < DP_PIN_ASSIGN_MAX as a loop condition.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix array-index-out-of-bounds read in add_missing_indices stbl is s8 but it must contain offsets into slot which can go from 0 to 127. Added a bound check for that error and return -EIO if the check fails. Also make jfs_readdir return with error if add_missing_indices returns with an error.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix out of bounds punch offset Punching a hole with a start offset that exceeds max_end is not permitted and will result in a negative length in the truncate_inode_partial_folio() function while truncating the page cache, potentially leading to undesirable consequences. A simple reproducer: truncate -s 9895604649994 /mnt/foo xfs_io -c "pwrite 8796093022208 4096" /mnt/foo xfs_io -c "fpunch 8796093022213 25769803777" /mnt/foo kernel BUG at include/linux/highmem.h:275! Oops: invalid opcode: 0000 [#1] SMP PTI CPU: 3 UID: 0 PID: 710 Comm: xfs_io Not tainted 6.15.0-rc3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:zero_user_segments.constprop.0+0xd7/0x110 RSP: 0018:ffffc90001cf3b38 EFLAGS: 00010287 RAX: 0000000000000005 RBX: ffffea0001485e40 RCX: 0000000000001000 RDX: 000000000040b000 RSI: 0000000000000005 RDI: 000000000040b000 RBP: 000000000040affb R08: ffff888000000000 R09: ffffea0000000000 R10: 0000000000000003 R11: 00000000fffc7fc5 R12: 0000000000000005 R13: 000000000040affb R14: ffffea0001485e40 R15: ffff888031cd3000 FS: 00007f4f63d0b780(0000) GS:ffff8880d337d000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000001ae0b038 CR3: 00000000536aa000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> truncate_inode_partial_folio+0x3dd/0x620 truncate_inode_pages_range+0x226/0x720 ? bdev_getblk+0x52/0x3e0 ? ext4_get_group_desc+0x78/0x150 ? crc32c_arch+0xfd/0x180 ? __ext4_get_inode_loc+0x18c/0x840 ? ext4_inode_csum+0x117/0x160 ? jbd2_journal_dirty_metadata+0x61/0x390 ? __ext4_handle_dirty_metadata+0xa0/0x2b0 ? kmem_cache_free+0x90/0x5a0 ? jbd2_journal_stop+0x1d5/0x550 ? __ext4_journal_stop+0x49/0x100 truncate_pagecache_range+0x50/0x80 ext4_truncate_page_cache_block_range+0x57/0x3a0 ext4_punch_hole+0x1fe/0x670 ext4_fallocate+0x792/0x17d0 ? __count_memcg_events+0x175/0x2a0 vfs_fallocate+0x121/0x560 ksys_fallocate+0x51/0xc0 __x64_sys_fallocate+0x24/0x40 x64_sys_call+0x18d2/0x4170 do_syscall_64+0xa7/0x220 entry_SYSCALL_64_after_hwframe+0x76/0x7e Fix this by filtering out cases where the punching start offset exceeds max_end.

In the Linux kernel, the following vulnerability has been resolved: pinctrl: at91: Fix possible out-of-boundary access at91_gpio_probe() doesn't check that given OF alias is not available or something went wrong when trying to get it. This might have consequences when accessing gpio_chips array with that value as an index. Note, that BUG() can be compiled out and hence won't actually perform the required checks.

In the Linux kernel, the following vulnerability has been resolved: 9p/net: fix improper handling of bogus negative read/write replies In p9_client_write() and p9_client_read_once(), if the server incorrectly replies with success but a negative write/read count then we would consider written (negative) <= rsize (positive) because both variables were signed. Make variables unsigned to avoid this problem. The reproducer linked below now fails with the following error instead of a null pointer deref: 9pnet: bogus RWRITE count (4294967295 > 3)

In the Linux kernel, the following vulnerability has been resolved: regulator: max20086: fix invalid memory access max20086_parse_regulators_dt() calls of_regulator_match() using an array of struct of_regulator_match allocated on the stack for the matches argument. of_regulator_match() calls devm_of_regulator_put_matches(), which calls devres_alloc() to allocate a struct devm_of_regulator_matches which will be de-allocated using devm_of_regulator_put_matches(). struct devm_of_regulator_matches is populated with the stack allocated matches array. If the device fails to probe, devm_of_regulator_put_matches() will be called and will try to call of_node_put() on that stack pointer, generating the following dmesg entries: max20086 6-0028: Failed to read DEVICE_ID reg: -121 kobject: '\xc0$\xa5\x03' (000000002cebcb7a): is not initialized, yet kobject_put() is being called. Followed by a stack trace matching the call flow described above. Switch to allocating the matches array using devm_kcalloc() to avoid accessing the stack pointer long after it's out of scope. This also has the advantage of allowing multiple max20086 to probe without overriding the data stored inside the global of_regulator_match.

In the Linux kernel, the following vulnerability has been resolved: spi-rockchip: Fix register out of bounds access Do not write native chip select stuff for GPIO chip selects. GPIOs can be numbered much higher than native CS. Also, it makes no sense.

In the Linux kernel, the following vulnerability has been resolved: regulator: gpio: Fix the out-of-bounds access to drvdata::gpiods drvdata::gpiods is supposed to hold an array of 'gpio_desc' pointers. But the memory is allocated for only one pointer. This will lead to out-of-bounds access later in the code if 'config::ngpios' is > 1. So fix the code to allocate enough memory to hold 'config::ngpios' of GPIO descriptors. While at it, also move the check for memory allocation failure to be below the allocation to make it more readable.

In the Linux kernel, the following vulnerability has been resolved: net/mdiobus: Fix potential out-of-bounds clause 45 read/write access When using publicly available tools like 'mdio-tools' to read/write data from/to network interface and its PHY via C45 (clause 45) mdiobus, there is no verification of parameters passed to the ioctl and it accepts any mdio address. Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define, but it is possible to pass higher value than that via ioctl. While read/write operation should generally fail in this case, mdiobus provides stats array, where wrong address may allow out-of-bounds read/write. Fix that by adding address verification before C45 read/write operation. While this excludes this access from any statistics, it improves security of read/write operation.

In the Linux kernel, the following vulnerability has been resolved: riscv: module: Fix out-of-bounds relocation access The current code allows rel[j] to access one element past the end of the relocation section. Simplify to num_relocations which is equivalent to the existing size expression.

In the Linux kernel, the following vulnerability has been resolved: powerpc/powernv/memtrace: Fix out of bounds issue in memtrace mmap memtrace mmap issue has an out of bounds issue. This patch fixes the by checking that the requested mapping region size should stay within the allocated region size.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix OOB read when checking dotdot dir Mounting a corrupted filesystem with directory which contains '.' dir entry with rec_len == block size results in out-of-bounds read (later on, when the corrupted directory is removed). ext4_empty_dir() assumes every ext4 directory contains at least '.' and '..' as directory entries in the first data block. It first loads the '.' dir entry, performs sanity checks by calling ext4_check_dir_entry() and then uses its rec_len member to compute the location of '..' dir entry (in ext4_next_entry). It assumes the '..' dir entry fits into the same data block. If the rec_len of '.' is precisely one block (4KB), it slips through the sanity checks (it is considered the last directory entry in the data block) and leaves "struct ext4_dir_entry_2 *de" point exactly past the memory slot allocated to the data block. The following call to ext4_check_dir_entry() on new value of de then dereferences this pointer which results in out-of-bounds mem access. Fix this by extending __ext4_check_dir_entry() to check for '.' dir entries that reach the end of data block. Make sure to ignore the phony dir entries for checksum (by checking name_len for non-zero). Note: This is reported by KASAN as use-after-free in case another structure was recently freed from the slot past the bound, but it is really an OOB read. This issue was found by syzkaller tool. Call Trace: [ 38.594108] BUG: KASAN: slab-use-after-free in __ext4_check_dir_entry+0x67e/0x710 [ 38.594649] Read of size 2 at addr ffff88802b41a004 by task syz-executor/5375 [ 38.595158] [ 38.595288] CPU: 0 UID: 0 PID: 5375 Comm: syz-executor Not tainted 6.14.0-rc7 #1 [ 38.595298] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 [ 38.595304] Call Trace: [ 38.595308] <TASK> [ 38.595311] dump_stack_lvl+0xa7/0xd0 [ 38.595325] print_address_description.constprop.0+0x2c/0x3f0 [ 38.595339] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595349] print_report+0xaa/0x250 [ 38.595359] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595368] ? kasan_addr_to_slab+0x9/0x90 [ 38.595378] kasan_report+0xab/0xe0 [ 38.595389] ? __ext4_check_dir_entry+0x67e/0x710 [ 38.595400] __ext4_check_dir_entry+0x67e/0x710 [ 38.595410] ext4_empty_dir+0x465/0x990 [ 38.595421] ? __pfx_ext4_empty_dir+0x10/0x10 [ 38.595432] ext4_rmdir.part.0+0x29a/0xd10 [ 38.595441] ? __dquot_initialize+0x2a7/0xbf0 [ 38.595455] ? __pfx_ext4_rmdir.part.0+0x10/0x10 [ 38.595464] ? __pfx___dquot_initialize+0x10/0x10 [ 38.595478] ? down_write+0xdb/0x140 [ 38.595487] ? __pfx_down_write+0x10/0x10 [ 38.595497] ext4_rmdir+0xee/0x140 [ 38.595506] vfs_rmdir+0x209/0x670 [ 38.595517] ? lookup_one_qstr_excl+0x3b/0x190 [ 38.595529] do_rmdir+0x363/0x3c0 [ 38.595537] ? __pfx_do_rmdir+0x10/0x10 [ 38.595544] ? strncpy_from_user+0x1ff/0x2e0 [ 38.595561] __x64_sys_unlinkat+0xf0/0x130 [ 38.595570] do_syscall_64+0x5b/0x180 [ 38.595583] entry_SYSCALL_64_after_hwframe+0x76/0x7e

In the Linux kernel, the following vulnerability has been resolved: arm64: mops: Do not dereference src reg for a set operation The source register is not used for SET* and reading it can result in a UBSAN out-of-bounds array access error, specifically when the MOPS exception is taken from a SET* sequence with XZR (reg 31) as the source. Architecturally this is the only case where a src/dst/size field in the ESR can be reported as 31. Prior to 2de451a329cf662b the code in do_el0_mops() was benign as the use of pt_regs_read_reg() prevented the out-of-bounds access.

In the Linux kernel, the following vulnerability has been resolved: HID: usbhid: Eliminate recurrent out-of-bounds bug in usbhid_parse() Update struct hid_descriptor to better reflect the mandatory and optional parts of the HID Descriptor as per USB HID 1.11 specification. Note: the kernel currently does not parse any optional HID class descriptors, only the mandatory report descriptor. Update all references to member element desc[0] to rpt_desc. Add test to verify bLength and bNumDescriptors values are valid. Replace the for loop with direct access to the mandatory HID class descriptor member for the report descriptor. This eliminates the possibility of getting an out-of-bounds fault. Add a warning message if the HID descriptor contains any unsupported optional HID class descriptors.

In the Linux kernel, the following vulnerability has been resolved: net/mdiobus: Fix potential out-of-bounds read/write access When using publicly available tools like 'mdio-tools' to read/write data from/to network interface and its PHY via mdiobus, there is no verification of parameters passed to the ioctl and it accepts any mdio address. Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define, but it is possible to pass higher value than that via ioctl. While read/write operation should generally fail in this case, mdiobus provides stats array, where wrong address may allow out-of-bounds read/write. Fix that by adding address verification before read/write operation. While this excludes this access from any statistics, it improves security of read/write operation.

In the Linux kernel, the following vulnerability has been resolved: bnxt_en: Fix out-of-bound memcpy() during ethtool -w When retrieving the FW coredump using ethtool, it can sometimes cause memory corruption: BUG: KFENCE: memory corruption in __bnxt_get_coredump+0x3ef/0x670 [bnxt_en] Corrupted memory at 0x000000008f0f30e8 [ ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ] (in kfence-#45): __bnxt_get_coredump+0x3ef/0x670 [bnxt_en] ethtool_get_dump_data+0xdc/0x1a0 __dev_ethtool+0xa1e/0x1af0 dev_ethtool+0xa8/0x170 dev_ioctl+0x1b5/0x580 sock_do_ioctl+0xab/0xf0 sock_ioctl+0x1ce/0x2e0 __x64_sys_ioctl+0x87/0xc0 do_syscall_64+0x5c/0xf0 entry_SYSCALL_64_after_hwframe+0x78/0x80 ... This happens when copying the coredump segment list in bnxt_hwrm_dbg_dma_data() with the HWRM_DBG_COREDUMP_LIST FW command. The info->dest_buf buffer is allocated based on the number of coredump segments returned by the FW. The segment list is then DMA'ed by the FW and the length of the DMA is returned by FW. The driver then copies this DMA'ed segment list to info->dest_buf. In some cases, this DMA length may exceed the info->dest_buf length and cause the above BUG condition. Fix it by capping the copy length to not exceed the length of info->dest_buf. The extra DMA data contains no useful information. This code path is shared for the HWRM_DBG_COREDUMP_LIST and the HWRM_DBG_COREDUMP_RETRIEVE FW commands. The buffering is different for these 2 FW commands. To simplify the logic, we need to move the line to adjust the buffer length for HWRM_DBG_COREDUMP_RETRIEVE up, so that the new check to cap the copy length will work for both commands.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix invalid access to memory In ath12k_dp_rx_msdu_coalesce(), rxcb is fetched from skb and boolean is_continuation is part of rxcb. Currently, after freeing the skb, the rxcb->is_continuation accessed again which is wrong since the memory is already freed. This might lead use-after-free error. Hence, fix by locally defining bool is_continuation from rxcb, so that after freeing skb, is_continuation can be used. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: netfs: Fix oops in write-retry from mis-resetting the subreq iterator Fix the resetting of the subrequest iterator in netfs_retry_write_stream() to use the iterator-reset function as the iterator may have been shortened by a previous retry. In such a case, the amount of data to be written by the subrequest is not "subreq->len" but "subreq->len - subreq->transferred". Without this, KASAN may see an error in iov_iter_revert(): BUG: KASAN: slab-out-of-bounds in iov_iter_revert lib/iov_iter.c:633 [inline] BUG: KASAN: slab-out-of-bounds in iov_iter_revert+0x443/0x5a0 lib/iov_iter.c:611 Read of size 4 at addr ffff88802912a0b8 by task kworker/u32:7/1147 CPU: 1 UID: 0 PID: 1147 Comm: kworker/u32:7 Not tainted 6.15.0-rc6-syzkaller-00052-g9f35e33144ae #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Workqueue: events_unbound netfs_write_collection_worker Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xc3/0x670 mm/kasan/report.c:521 kasan_report+0xe0/0x110 mm/kasan/report.c:634 iov_iter_revert lib/iov_iter.c:633 [inline] iov_iter_revert+0x443/0x5a0 lib/iov_iter.c:611 netfs_retry_write_stream fs/netfs/write_retry.c:44 [inline] netfs_retry_writes+0x166d/0x1a50 fs/netfs/write_retry.c:231 netfs_collect_write_results fs/netfs/write_collect.c:352 [inline] netfs_write_collection_worker+0x23fd/0x3830 fs/netfs/write_collect.c:374 process_one_work+0x9cf/0x1b70 kernel/workqueue.c:3238 process_scheduled_works kernel/workqueue.c:3319 [inline] worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400 kthread+0x3c2/0x780 kernel/kthread.c:464 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK>

In the Linux kernel, the following vulnerability has been resolved: nvmet: fix out-of-bounds access in nvmet_enable_port When trying to enable a port that has no transport configured yet, nvmet_enable_port() uses NVMF_TRTYPE_MAX (255) to query the transports array, causing an out-of-bounds access: [ 106.058694] BUG: KASAN: global-out-of-bounds in nvmet_enable_port+0x42/0x1da [ 106.058719] Read of size 8 at addr ffffffff89dafa58 by task ln/632 [...] [ 106.076026] nvmet: transport type 255 not supported Since commit 200adac75888, NVMF_TRTYPE_MAX is the default state as configured by nvmet_ports_make(). Avoid this by checking for NVMF_TRTYPE_MAX before proceeding.

In the Linux kernel, the following vulnerability has been resolved: net: usb: aqc111: fix error handling of usbnet read calls Syzkaller, courtesy of syzbot, identified an error (see report [1]) in aqc111 driver, caused by incomplete sanitation of usb read calls' results. This problem is quite similar to the one fixed in commit 920a9fa27e78 ("net: asix: add proper error handling of usb read errors"). For instance, usbnet_read_cmd() may read fewer than 'size' bytes, even if the caller expected the full amount, and aqc111_read_cmd() will not check its result properly. As [1] shows, this may lead to MAC address in aqc111_bind() being only partly initialized, triggering KMSAN warnings. Fix the issue by verifying that the number of bytes read is as expected and not less. [1] Partial syzbot report: BUG: KMSAN: uninit-value in is_valid_ether_addr include/linux/etherdevice.h:208 [inline] BUG: KMSAN: uninit-value in usbnet_probe+0x2e57/0x4390 drivers/net/usb/usbnet.c:1830 is_valid_ether_addr include/linux/etherdevice.h:208 [inline] usbnet_probe+0x2e57/0x4390 drivers/net/usb/usbnet.c:1830 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:-1 [inline] really_probe+0x4d1/0xd90 drivers/base/dd.c:658 __driver_probe_device+0x268/0x380 drivers/base/dd.c:800 ... Uninit was stored to memory at: dev_addr_mod+0xb0/0x550 net/core/dev_addr_lists.c:582 __dev_addr_set include/linux/netdevice.h:4874 [inline] eth_hw_addr_set include/linux/etherdevice.h:325 [inline] aqc111_bind+0x35f/0x1150 drivers/net/usb/aqc111.c:717 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 ... Uninit was stored to memory at: ether_addr_copy include/linux/etherdevice.h:305 [inline] aqc111_read_perm_mac drivers/net/usb/aqc111.c:663 [inline] aqc111_bind+0x794/0x1150 drivers/net/usb/aqc111.c:713 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:-1 [inline] ... Local variable buf.i created at: aqc111_read_perm_mac drivers/net/usb/aqc111.c:656 [inline] aqc111_bind+0x221/0x1150 drivers/net/usb/aqc111.c:713 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: fix the 'para' buffer size to avoid reading out of bounds Set the size to 6 instead of 2, since 'para' array is passed to 'rtw_fw_bt_wifi_control(rtwdev, para[0], &para[1])', which reads 5 bytes: void rtw_fw_bt_wifi_control(struct rtw_dev *rtwdev, u8 op_code, u8 *data) { ... SET_BT_WIFI_CONTROL_DATA1(h2c_pkt, *data); SET_BT_WIFI_CONTROL_DATA2(h2c_pkt, *(data + 1)); ... SET_BT_WIFI_CONTROL_DATA5(h2c_pkt, *(data + 4)); Detected using the static analysis tool - Svace.

In the Linux kernel, the following vulnerability has been resolved: can: bcm: add locking for bcm_op runtime updates The CAN broadcast manager (CAN BCM) can send a sequence of CAN frames via hrtimer. The content and also the length of the sequence can be changed resp reduced at runtime where the 'currframe' counter is then set to zero. Although this appeared to be a safe operation the updates of 'currframe' can be triggered from user space and hrtimer context in bcm_can_tx(). Anderson Nascimento created a proof of concept that triggered a KASAN slab-out-of-bounds read access which can be prevented with a spin_lock_bh. At the rework of bcm_can_tx() the 'count' variable has been moved into the protected section as this variable can be modified from both contexts too.

In the Linux kernel, the following vulnerability has been resolved: virtio-net: ensure the received length does not exceed allocated size In xdp_linearize_page, when reading the following buffers from the ring, we forget to check the received length with the true allocate size. This can lead to an out-of-bound read. This commit adds that missing check.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: fix out-of-bounds access during multi-link element defragmentation Currently during the multi-link element defragmentation process, the multi-link element length added to the total IEs length when calculating the length of remaining IEs after the multi-link element in cfg80211_defrag_mle(). This could lead to out-of-bounds access if the multi-link element or its corresponding fragment elements are the last elements in the IEs buffer. To address this issue, correctly calculate the remaining IEs length by deducting the multi-link element end offset from total IEs end offset.

In the Linux kernel, the following vulnerability has been resolved: isofs: Prevent the use of too small fid syzbot reported a slab-out-of-bounds Read in isofs_fh_to_parent. [1] The handle_bytes value passed in by the reproducing program is equal to 12. In handle_to_path(), only 12 bytes of memory are allocated for the structure file_handle->f_handle member, which causes an out-of-bounds access when accessing the member parent_block of the structure isofs_fid in isofs, because accessing parent_block requires at least 16 bytes of f_handle. Here, fh_len is used to indirectly confirm that the value of handle_bytes is greater than 3 before accessing parent_block. [1] BUG: KASAN: slab-out-of-bounds in isofs_fh_to_parent+0x1b8/0x210 fs/isofs/export.c:183 Read of size 4 at addr ffff0000cc030d94 by task syz-executor215/6466 CPU: 1 UID: 0 PID: 6466 Comm: syz-executor215 Not tainted 6.14.0-rc7-syzkaller-ga2392f333575 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Call trace: show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:466 (C) __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0xe4/0x150 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0x198/0x550 mm/kasan/report.c:521 kasan_report+0xd8/0x138 mm/kasan/report.c:634 __asan_report_load4_noabort+0x20/0x2c mm/kasan/report_generic.c:380 isofs_fh_to_parent+0x1b8/0x210 fs/isofs/export.c:183 exportfs_decode_fh_raw+0x2dc/0x608 fs/exportfs/expfs.c:523 do_handle_to_path+0xa0/0x198 fs/fhandle.c:257 handle_to_path fs/fhandle.c:385 [inline] do_handle_open+0x8cc/0xb8c fs/fhandle.c:403 __do_sys_open_by_handle_at fs/fhandle.c:443 [inline] __se_sys_open_by_handle_at fs/fhandle.c:434 [inline] __arm64_sys_open_by_handle_at+0x80/0x94 fs/fhandle.c:434 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132 do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151 el0_svc+0x54/0x168 arch/arm64/kernel/entry-common.c:744 el0t_64_sync_handler+0x84/0x108 arch/arm64/kernel/entry-common.c:762 el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600 Allocated by task 6466: kasan_save_stack mm/kasan/common.c:47 [inline] kasan_save_track+0x40/0x78 mm/kasan/common.c:68 kasan_save_alloc_info+0x40/0x50 mm/kasan/generic.c:562 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0xac/0xc4 mm/kasan/common.c:394 kasan_kmalloc include/linux/kasan.h:260 [inline] __do_kmalloc_node mm/slub.c:4294 [inline] __kmalloc_noprof+0x32c/0x54c mm/slub.c:4306 kmalloc_noprof include/linux/slab.h:905 [inline] handle_to_path fs/fhandle.c:357 [inline] do_handle_open+0x5a4/0xb8c fs/fhandle.c:403 __do_sys_open_by_handle_at fs/fhandle.c:443 [inline] __se_sys_open_by_handle_at fs/fhandle.c:434 [inline] __arm64_sys_open_by_handle_at+0x80/0x94 fs/fhandle.c:434 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132 do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151 el0_svc+0x54/0x168 arch/arm64/kernel/entry-common.c:744 el0t_64_sync_handler+0x84/0x108 arch/arm64/kernel/entry-common.c:762 el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600

An issue was discovered in fs/f2fs/super.c in the Linux kernel through 4.14. A denial of service (out-of-bounds memory access and BUG) can occur upon encountering an abnormal bitmap size when mounting a crafted f2fs image.

Adobe Flash Player 30.0.0.134 and earlier have an out-of-bounds read vulnerability. Successful exploitation could lead to information disclosure.

Linux kernel ext4 filesystem is vulnerable to an out-of-bound access in the ext4_ext_drop_refs() function when operating on a crafted ext4 filesystem image.

In the Linux kernel before 5.2.3, set_geometry in drivers/block/floppy.c does not validate the sect and head fields, as demonstrated by an integer overflow and out-of-bounds read. It can be triggered by an unprivileged local user when a floppy disk has been inserted. NOTE: QEMU creates the floppy device by default.

In the Linux kernel, the following vulnerability has been resolved: net: ena: fix shift-out-of-bounds in exponential backoff The ENA adapters on our instances occasionally reset. Once recently logged a UBSAN failure to console in the process: UBSAN: shift-out-of-bounds in build/linux/drivers/net/ethernet/amazon/ena/ena_com.c:540:13 shift exponent 32 is too large for 32-bit type 'unsigned int' CPU: 28 PID: 70012 Comm: kworker/u72:2 Kdump: loaded not tainted 5.15.117 Hardware name: Amazon EC2 c5d.9xlarge/, BIOS 1.0 10/16/2017 Workqueue: ena ena_fw_reset_device [ena] Call Trace: <TASK> dump_stack_lvl+0x4a/0x63 dump_stack+0x10/0x16 ubsan_epilogue+0x9/0x36 __ubsan_handle_shift_out_of_bounds.cold+0x61/0x10e ? __const_udelay+0x43/0x50 ena_delay_exponential_backoff_us.cold+0x16/0x1e [ena] wait_for_reset_state+0x54/0xa0 [ena] ena_com_dev_reset+0xc8/0x110 [ena] ena_down+0x3fe/0x480 [ena] ena_destroy_device+0xeb/0xf0 [ena] ena_fw_reset_device+0x30/0x50 [ena] process_one_work+0x22b/0x3d0 worker_thread+0x4d/0x3f0 ? process_one_work+0x3d0/0x3d0 kthread+0x12a/0x150 ? set_kthread_struct+0x50/0x50 ret_from_fork+0x22/0x30 </TASK> Apparently, the reset delays are getting so large they can trigger a UBSAN panic. Looking at the code, the current timeout is capped at 5000us. Using a base value of 100us, the current code will overflow after (1<<29). Even at values before 32, this function wraps around, perhaps unintentionally. Cap the value of the exponent used for this backoff at (1<<16) which is larger than currently necessary, but large enough to support bigger values in the future.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix possible out-of-bound read in ath12k_htt_pull_ppdu_stats() len is extracted from HTT message and could be an unexpected value in case errors happen, so add validation before using to avoid possible out-of-bound read in the following message iteration and parsing. The same issue also applies to ppdu_info->ppdu_stats.common.num_users, so validate it before using too. These are found during code review. Compile test only.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpi3mr: Use number of bits to manage bitmap sizes To allocate bitmaps, the mpi3mr driver calculates sizes of bitmaps using byte as unit. However, bitmap helper functions assume that bitmaps are allocated using unsigned long as unit. This gap causes memory access beyond the bitmap sizes and results in "BUG: KASAN: slab-out-of-bounds". The BUG was observed at firmware download to eHBA-9600. Call trace indicated that the out-of-bounds access happened in find_first_zero_bit() called from mpi3mr_send_event_ack() for miroc->evtack_cmds_bitmap. To fix the BUG, do not use bytes to manage bitmap sizes. Instead, use number of bits, and call bitmap helper functions which take number of bits as arguments. For memory allocation, call bitmap_zalloc() instead of kzalloc() and krealloc(). For memory free, call bitmap_free() instead of kfree(). For zero clear, call bitmap_clear() instead of memset(). Remove three fields for bitmap byte sizes in struct scmd_priv which are no longer required. Replace the field dev_handle_bitmap_sz with dev_handle_bitmap_bits to keep number of bits of removepend_bitmap across resize.

NVIDIA CUDA Toolkit for all platforms contains a vulnerability in the nvdisasm binary where a user may cause an out-of-bounds read by passing a malformed ELF file to nvdisasm. A successful exploit of this vulnerability may lead to a partial denial of service.

NVIDIA CUDA Toolkit for all platforms contains a vulnerability in the nvdisasm binary where a user may cause an out-of-bounds read by passing a malformed ELF file to nvdisasm. A successful exploit of this vulnerability may lead to a partial denial of service.

In the Linux kernel, the following vulnerability has been resolved: media: venus: hfi_parser: add check to avoid out of bound access There is a possibility that init_codecs is invoked multiple times during manipulated payload from video firmware. In such case, if codecs_count can get incremented to value more than MAX_CODEC_NUM, there can be OOB access. Reset the count so that it always starts from beginning.

NVIDIA Triton Inference Server for Windows and Linux contains a vulnerability in the Python backend, where an attacker could cause an out-of-bounds read by sending a request. A successful exploit of this vulnerability might lead to information disclosure.

In the Linux kernel, the following vulnerability has been resolved: USB: core: Fix race by not overwriting udev->descriptor in hub_port_init() Syzbot reported an out-of-bounds read in sysfs.c:read_descriptors(): BUG: KASAN: slab-out-of-bounds in read_descriptors+0x263/0x280 drivers/usb/core/sysfs.c:883 Read of size 8 at addr ffff88801e78b8c8 by task udevd/5011 CPU: 0 PID: 5011 Comm: udevd Not tainted 6.4.0-rc6-syzkaller-00195-g40f71e7cd3c6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106 print_address_description.constprop.0+0x2c/0x3c0 mm/kasan/report.c:351 print_report mm/kasan/report.c:462 [inline] kasan_report+0x11c/0x130 mm/kasan/report.c:572 read_descriptors+0x263/0x280 drivers/usb/core/sysfs.c:883 ... Allocated by task 758: ... __do_kmalloc_node mm/slab_common.c:966 [inline] __kmalloc+0x5e/0x190 mm/slab_common.c:979 kmalloc include/linux/slab.h:563 [inline] kzalloc include/linux/slab.h:680 [inline] usb_get_configuration+0x1f7/0x5170 drivers/usb/core/config.c:887 usb_enumerate_device drivers/usb/core/hub.c:2407 [inline] usb_new_device+0x12b0/0x19d0 drivers/usb/core/hub.c:2545 As analyzed by Khazhy Kumykov, the cause of this bug is a race between read_descriptors() and hub_port_init(): The first routine uses a field in udev->descriptor, not expecting it to change, while the second overwrites it. Prior to commit 45bf39f8df7f ("USB: core: Don't hold device lock while reading the "descriptors" sysfs file") this race couldn't occur, because the routines were mutually exclusive thanks to the device locking. Removing that locking from read_descriptors() exposed it to the race. The best way to fix the bug is to keep hub_port_init() from changing udev->descriptor once udev has been initialized and registered. Drivers expect the descriptors stored in the kernel to be immutable; we should not undermine this expectation. In fact, this change should have been made long ago. So now hub_port_init() will take an additional argument, specifying a buffer in which to store the device descriptor it reads. (If udev has not yet been initialized, the buffer pointer will be NULL and then hub_port_init() will store the device descriptor in udev as before.) This eliminates the data race responsible for the out-of-bounds read. The changes to hub_port_init() appear more extensive than they really are, because of indentation changes resulting from an attempt to avoid writing to other parts of the usb_device structure after it has been initialized. Similar changes should be made to the code that reads the BOS descriptor, but that can be handled in a separate patch later on. This patch is sufficient to fix the bug found by syzbot.