In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Add 0 size check to mtk_drm_gem_obj Add a check to mtk_drm_gem_init if we attempt to allocate a GEM object of 0 bytes. Currently, no such check exists and the kernel will panic if a userspace application attempts to allocate a 0x0 GBM buffer. Tested by attempting to allocate a 0x0 GBM buffer on an MT8188 and verifying that we now return EINVAL.

In the Linux kernel, the following vulnerability has been resolved: hsr: hold rcu and dev lock for hsr_get_port_ndev hsr_get_port_ndev calls hsr_for_each_port, which need to hold rcu lock. On the other hand, before return the port device, we need to hold the device reference to avoid UaF in the caller function.

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: Remove WARN_ON for device endpoint command timeouts This commit addresses a rarely observed endpoint command timeout which causes kernel panic due to warn when 'panic_on_warn' is enabled and unnecessary call trace prints when 'panic_on_warn' is disabled. It is seen during fast software-controlled connect/disconnect testcases. The following is one such endpoint command timeout that we observed: 1. Connect ======= ->dwc3_thread_interrupt ->dwc3_ep0_interrupt ->configfs_composite_setup ->composite_setup ->usb_ep_queue ->dwc3_gadget_ep0_queue ->__dwc3_gadget_ep0_queue ->__dwc3_ep0_do_control_data ->dwc3_send_gadget_ep_cmd 2. Disconnect ========== ->dwc3_thread_interrupt ->dwc3_gadget_disconnect_interrupt ->dwc3_ep0_reset_state ->dwc3_ep0_end_control_data ->dwc3_send_gadget_ep_cmd In the issue scenario, in Exynos platforms, we observed that control transfers for the previous connect have not yet been completed and end transfer command sent as a part of the disconnect sequence and processing of USB_ENDPOINT_HALT feature request from the host timeout. This maybe an expected scenario since the controller is processing EP commands sent as a part of the previous connect. It maybe better to remove WARN_ON in all places where device endpoint commands are sent to avoid unnecessary kernel panic due to warn.

In the Linux kernel, the following vulnerability has been resolved: sched: Fix sched_numa_find_nth_cpu() if mask offline sched_numa_find_nth_cpu() uses a bsearch to look for the 'closest' CPU in sched_domains_numa_masks and given cpus mask. However they might not intersect if all CPUs in the cpus mask are offline. bsearch will return NULL in that case, bail out instead of dereferencing a bogus pointer. The previous behaviour lead to this bug when using maxcpus=4 on an rk3399 (LLLLbb) (i.e. booting with all big CPUs offline): [ 1.422922] Unable to handle kernel paging request at virtual address ffffff8000000000 [ 1.423635] Mem abort info: [ 1.423889] ESR = 0x0000000096000006 [ 1.424227] EC = 0x25: DABT (current EL), IL = 32 bits [ 1.424715] SET = 0, FnV = 0 [ 1.424995] EA = 0, S1PTW = 0 [ 1.425279] FSC = 0x06: level 2 translation fault [ 1.425735] Data abort info: [ 1.425998] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000 [ 1.426499] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 1.426952] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 1.427428] swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000004a9f000 [ 1.428038] [ffffff8000000000] pgd=18000000f7fff403, p4d=18000000f7fff403, pud=18000000f7fff403, pmd=0000000000000000 [ 1.429014] Internal error: Oops: 0000000096000006 [#1] SMP [ 1.429525] Modules linked in: [ 1.429813] CPU: 3 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.17.0-rc4-dirty #343 PREEMPT [ 1.430559] Hardware name: Pine64 RockPro64 v2.1 (DT) [ 1.431012] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 1.431634] pc : sched_numa_find_nth_cpu+0x2a0/0x488 [ 1.432094] lr : sched_numa_find_nth_cpu+0x284/0x488 [ 1.432543] sp : ffffffc084e1b960 [ 1.432843] x29: ffffffc084e1b960 x28: ffffff80078a8800 x27: ffffffc0846eb1d0 [ 1.433495] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 [ 1.434144] x23: 0000000000000000 x22: fffffffffff7f093 x21: ffffffc081de6378 [ 1.434792] x20: 0000000000000000 x19: 0000000ffff7f093 x18: 00000000ffffffff [ 1.435441] x17: 3030303866666666 x16: 66663d736b73616d x15: ffffffc104e1b5b7 [ 1.436091] x14: 0000000000000000 x13: ffffffc084712860 x12: 0000000000000372 [ 1.436739] x11: 0000000000000126 x10: ffffffc08476a860 x9 : ffffffc084712860 [ 1.437389] x8 : 00000000ffffefff x7 : ffffffc08476a860 x6 : 0000000000000000 [ 1.438036] x5 : 000000000000bff4 x4 : 0000000000000000 x3 : 0000000000000000 [ 1.438683] x2 : 0000000000000000 x1 : ffffffc0846eb000 x0 : ffffff8000407b68 [ 1.439332] Call trace: [ 1.439559] sched_numa_find_nth_cpu+0x2a0/0x488 (P) [ 1.440016] smp_call_function_any+0xc8/0xd0 [ 1.440416] armv8_pmu_init+0x58/0x27c [ 1.440770] armv8_cortex_a72_pmu_init+0x20/0x2c [ 1.441199] arm_pmu_device_probe+0x1e4/0x5e8 [ 1.441603] armv8_pmu_device_probe+0x1c/0x28 [ 1.442007] platform_probe+0x5c/0xac [ 1.442347] really_probe+0xbc/0x298 [ 1.442683] __driver_probe_device+0x78/0x12c [ 1.443087] driver_probe_device+0xdc/0x160 [ 1.443475] __driver_attach+0x94/0x19c [ 1.443833] bus_for_each_dev+0x74/0xd4 [ 1.444190] driver_attach+0x24/0x30 [ 1.444525] bus_add_driver+0xe4/0x208 [ 1.444874] driver_register+0x60/0x128 [ 1.445233] __platform_driver_register+0x24/0x30 [ 1.445662] armv8_pmu_driver_init+0x28/0x4c [ 1.446059] do_one_initcall+0x44/0x25c [ 1.446416] kernel_init_freeable+0x1dc/0x3bc [ 1.446820] kernel_init+0x20/0x1d8 [ 1.447151] ret_from_fork+0x10/0x20 [ 1.447493] Code: 90022e21 f000e5f5 910de2b5 2a1703e2 (f8767803) [ 1.448040] ---[ end trace 0000000000000000 ]--- [ 1.448483] note: swapper/0[1] exited with preempt_count 1 [ 1.449047] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 1.449741] SMP: stopping secondary CPUs [ 1.450105] Kernel Offset: disabled [ 1.450419] CPU features: 0x000000,00080000,20002001,0400421b [ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: vsock/virtio: Validate length in packet header before skb_put() When receiving a vsock packet in the guest, only the virtqueue buffer size is validated prior to virtio_vsock_skb_rx_put(). Unfortunately, virtio_vsock_skb_rx_put() uses the length from the packet header as the length argument to skb_put(), potentially resulting in SKB overflow if the host has gone wonky. Validate the length as advertised by the packet header before calling virtio_vsock_skb_rx_put().

In the Linux kernel, the following vulnerability has been resolved: dm: dm-crypt: Do not partially accept write BIOs with zoned targets Read and write operations issued to a dm-crypt target may be split according to the dm-crypt internal limits defined by the max_read_size and max_write_size module parameters (default is 128 KB). The intent is to improve processing time of large BIOs by splitting them into smaller operations that can be parallelized on different CPUs. For zoned dm-crypt targets, this BIO splitting is still done but without the parallel execution to ensure that the issuing order of write operations to the underlying devices remains sequential. However, the splitting itself causes other problems: 1) Since dm-crypt relies on the block layer zone write plugging to handle zone append emulation using regular write operations, the reminder of a split write BIO will always be plugged into the target zone write plugged. Once the on-going write BIO finishes, this reminder BIO is unplugged and issued from the zone write plug work. If this reminder BIO itself needs to be split, the reminder will be re-issued and plugged again, but that causes a call to a blk_queue_enter(), which may block if a queue freeze operation was initiated. This results in a deadlock as DM submission still holds BIOs that the queue freeze side is waiting for. 2) dm-crypt relies on the emulation done by the block layer using regular write operations for processing zone append operations. This still requires to properly return the written sector as the BIO sector of the original BIO. However, this can be done correctly only and only if there is a single clone BIO used for processing the original zone append operation issued by the user. If the size of a zone append operation is larger than dm-crypt max_write_size, then the orginal BIO will be split and processed as a chain of regular write operations. Such chaining result in an incorrect written sector being returned to the zone append issuer using the original BIO sector. This in turn results in file system data corruptions using xfs or btrfs. Fix this by modifying get_max_request_size() to always return the size of the BIO to avoid it being split with dm_accpet_partial_bio() in crypt_map(). get_max_request_size() is renamed to get_max_request_sectors() to clarify the unit of the value returned and its interface is changed to take a struct dm_target pointer and a pointer to the struct bio being processed. In addition to this change, to ensure that crypt_alloc_buffer() works correctly, set the dm-crypt device max_hw_sectors limit to be at most BIO_MAX_VECS << PAGE_SECTORS_SHIFT (1 MB with a 4KB page architecture). This forces DM core to split write BIOs before passing them to crypt_map(), and thus guaranteeing that dm-crypt can always accept an entire write BIO without needing to split it. This change does not have any effect on the read path of dm-crypt. Read operations can still be split and the BIO fragments processed in parallel. There is also no impact on the performance of the write path given that all zone write BIOs were already processed inline instead of in parallel. This change also does not affect in any way regular dm-crypt block devices.

In the Linux kernel, the following vulnerability has been resolved: jbd2: prevent softlockup in jbd2_log_do_checkpoint() Both jbd2_log_do_checkpoint() and jbd2_journal_shrink_checkpoint_list() periodically release j_list_lock after processing a batch of buffers to avoid long hold times on the j_list_lock. However, since both functions contend for j_list_lock, the combined time spent waiting and processing can be significant. jbd2_journal_shrink_checkpoint_list() explicitly calls cond_resched() when need_resched() is true to avoid softlockups during prolonged operations. But jbd2_log_do_checkpoint() only exits its loop when need_resched() is true, relying on potentially sleeping functions like __flush_batch() or wait_on_buffer() to trigger rescheduling. If those functions do not sleep, the kernel may hit a softlockup. watchdog: BUG: soft lockup - CPU#3 stuck for 156s! [kworker/u129:2:373] CPU: 3 PID: 373 Comm: kworker/u129:2 Kdump: loaded Not tainted 6.6.0+ #10 Hardware name: Huawei TaiShan 2280 /BC11SPCD, BIOS 1.27 06/13/2017 Workqueue: writeback wb_workfn (flush-7:2) pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : native_queued_spin_lock_slowpath+0x358/0x418 lr : jbd2_log_do_checkpoint+0x31c/0x438 [jbd2] Call trace: native_queued_spin_lock_slowpath+0x358/0x418 jbd2_log_do_checkpoint+0x31c/0x438 [jbd2] __jbd2_log_wait_for_space+0xfc/0x2f8 [jbd2] add_transaction_credits+0x3bc/0x418 [jbd2] start_this_handle+0xf8/0x560 [jbd2] jbd2__journal_start+0x118/0x228 [jbd2] __ext4_journal_start_sb+0x110/0x188 [ext4] ext4_do_writepages+0x3dc/0x740 [ext4] ext4_writepages+0xa4/0x190 [ext4] do_writepages+0x94/0x228 __writeback_single_inode+0x48/0x318 writeback_sb_inodes+0x204/0x590 __writeback_inodes_wb+0x54/0xf8 wb_writeback+0x2cc/0x3d8 wb_do_writeback+0x2e0/0x2f8 wb_workfn+0x80/0x2a8 process_one_work+0x178/0x3e8 worker_thread+0x234/0x3b8 kthread+0xf0/0x108 ret_from_fork+0x10/0x20 So explicitly call cond_resched() in jbd2_log_do_checkpoint() to avoid softlockup.

In the Linux kernel, the following vulnerability has been resolved: ice: fix NULL pointer dereference in ice_unplug_aux_dev() on reset Issuing a reset when the driver is loaded without RDMA support, will results in a crash as it attempts to remove RDMA's non-existent auxbus device: echo 1 > /sys/class/net/<if>/device/reset BUG: kernel NULL pointer dereference, address: 0000000000000008 ... RIP: 0010:ice_unplug_aux_dev+0x29/0x70 [ice] ... Call Trace: <TASK> ice_prepare_for_reset+0x77/0x260 [ice] pci_dev_save_and_disable+0x2c/0x70 pci_reset_function+0x88/0x130 reset_store+0x5a/0xa0 kernfs_fop_write_iter+0x15e/0x210 vfs_write+0x273/0x520 ksys_write+0x6b/0xe0 do_syscall_64+0x79/0x3b0 entry_SYSCALL_64_after_hwframe+0x76/0x7e ice_unplug_aux_dev() checks pf->cdev_info->adev for NULL pointer, but pf->cdev_info will also be NULL, leading to the deref in the trace above. Introduce a flag to be set when the creation of the auxbus device is successful, to avoid multiple NULL pointer checks in ice_unplug_aux_dev().

In the Linux kernel, the following vulnerability has been resolved: mm/kmemleak: avoid soft lockup in __kmemleak_do_cleanup() A soft lockup warning was observed on a relative small system x86-64 system with 16 GB of memory when running a debug kernel with kmemleak enabled. watchdog: BUG: soft lockup - CPU#8 stuck for 33s! [kworker/8:1:134] The test system was running a workload with hot unplug happening in parallel. Then kemleak decided to disable itself due to its inability to allocate more kmemleak objects. The debug kernel has its CONFIG_DEBUG_KMEMLEAK_MEM_POOL_SIZE set to 40,000. The soft lockup happened in kmemleak_do_cleanup() when the existing kmemleak objects were being removed and deleted one-by-one in a loop via a workqueue. In this particular case, there are at least 40,000 objects that need to be processed and given the slowness of a debug kernel and the fact that a raw_spinlock has to be acquired and released in __delete_object(), it could take a while to properly handle all these objects. As kmemleak has been disabled in this case, the object removal and deletion process can be further optimized as locking isn't really needed. However, it is probably not worth the effort to optimize for such an edge case that should rarely happen. So the simple solution is to call cond_resched() at periodic interval in the iteration loop to avoid soft lockup.

In the Linux kernel, the following vulnerability has been resolved: net: drop UFO packets in udp_rcv_segment() When sending a packet with virtio_net_hdr to tun device, if the gso_type in virtio_net_hdr is SKB_GSO_UDP and the gso_size is less than udphdr size, below crash may happen. ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:4572! Oops: invalid opcode: 0000 [#1] SMP NOPTI CPU: 0 UID: 0 PID: 62 Comm: mytest Not tainted 6.16.0-rc7 #203 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:skb_pull_rcsum+0x8e/0xa0 Code: 00 00 5b c3 cc cc cc cc 8b 93 88 00 00 00 f7 da e8 37 44 38 00 f7 d8 89 83 88 00 00 00 48 8b 83 c8 00 00 00 5b c3 cc cc cc cc <0f> 0b 0f 0b 66 66 2e 0f 1f 84 00 000 RSP: 0018:ffffc900001fba38 EFLAGS: 00000297 RAX: 0000000000000004 RBX: ffff8880040c1000 RCX: ffffc900001fb948 RDX: ffff888003e6d700 RSI: 0000000000000008 RDI: ffff88800411a062 RBP: ffff8880040c1000 R08: 0000000000000000 R09: 0000000000000001 R10: ffff888003606c00 R11: 0000000000000001 R12: 0000000000000000 R13: ffff888004060900 R14: ffff888004050000 R15: ffff888004060900 FS: 000000002406d3c0(0000) GS:ffff888084a19000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000040 CR3: 0000000004007000 CR4: 00000000000006f0 Call Trace: <TASK> udp_queue_rcv_one_skb+0x176/0x4b0 net/ipv4/udp.c:2445 udp_queue_rcv_skb+0x155/0x1f0 net/ipv4/udp.c:2475 udp_unicast_rcv_skb+0x71/0x90 net/ipv4/udp.c:2626 __udp4_lib_rcv+0x433/0xb00 net/ipv4/udp.c:2690 ip_protocol_deliver_rcu+0xa6/0x160 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x72/0x90 net/ipv4/ip_input.c:233 ip_sublist_rcv_finish+0x5f/0x70 net/ipv4/ip_input.c:579 ip_sublist_rcv+0x122/0x1b0 net/ipv4/ip_input.c:636 ip_list_rcv+0xf7/0x130 net/ipv4/ip_input.c:670 __netif_receive_skb_list_core+0x21d/0x240 net/core/dev.c:6067 netif_receive_skb_list_internal+0x186/0x2b0 net/core/dev.c:6210 napi_complete_done+0x78/0x180 net/core/dev.c:6580 tun_get_user+0xa63/0x1120 drivers/net/tun.c:1909 tun_chr_write_iter+0x65/0xb0 drivers/net/tun.c:1984 vfs_write+0x300/0x420 fs/read_write.c:593 ksys_write+0x60/0xd0 fs/read_write.c:686 do_syscall_64+0x50/0x1c0 arch/x86/entry/syscall_64.c:63 </TASK> To trigger gso segment in udp_queue_rcv_skb(), we should also set option UDP_ENCAP_ESPINUDP to enable udp_sk(sk)->encap_rcv. When the encap_rcv hook return 1 in udp_queue_rcv_one_skb(), udp_csum_pull_header() will try to pull udphdr, but the skb size has been segmented to gso size, which leads to this crash. Previous commit cf329aa42b66 ("udp: cope with UDP GRO packet misdirection") introduces segmentation in UDP receive path only for GRO, which was never intended to be used for UFO, so drop UFO packets in udp_rcv_segment().

In the Linux kernel, the following vulnerability has been resolved: smb: client: let recv_done verify data_offset, data_length and remaining_data_length This is inspired by the related server fixes.

In the Linux kernel, the following vulnerability has been resolved: net_sched: gen_estimator: fix est_timer() vs CONFIG_PREEMPT_RT=y syzbot reported a WARNING in est_timer() [1] Problem here is that with CONFIG_PREEMPT_RT=y, timer callbacks can be preempted. Adopt preempt_disable_nested()/preempt_enable_nested() to fix this. [1] WARNING: CPU: 0 PID: 16 at ./include/linux/seqlock.h:221 __seqprop_assert include/linux/seqlock.h:221 [inline] WARNING: CPU: 0 PID: 16 at ./include/linux/seqlock.h:221 est_timer+0x6dc/0x9f0 net/core/gen_estimator.c:93 Modules linked in: CPU: 0 UID: 0 PID: 16 Comm: ktimers/0 Not tainted syzkaller #0 PREEMPT_{RT,(full)} Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/12/2025 RIP: 0010:__seqprop_assert include/linux/seqlock.h:221 [inline] RIP: 0010:est_timer+0x6dc/0x9f0 net/core/gen_estimator.c:93 Call Trace: <TASK> call_timer_fn+0x17e/0x5f0 kernel/time/timer.c:1747 expire_timers kernel/time/timer.c:1798 [inline] __run_timers kernel/time/timer.c:2372 [inline] __run_timer_base+0x648/0x970 kernel/time/timer.c:2384 run_timer_base kernel/time/timer.c:2393 [inline] run_timer_softirq+0xb7/0x180 kernel/time/timer.c:2403 handle_softirqs+0x22c/0x710 kernel/softirq.c:579 __do_softirq kernel/softirq.c:613 [inline] run_ktimerd+0xcf/0x190 kernel/softirq.c:1043 smpboot_thread_fn+0x53f/0xa60 kernel/smpboot.c:160 kthread+0x70e/0x8a0 kernel/kthread.c:463 ret_from_fork+0x3fc/0x770 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK>

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: clear initialized flag for deinit-ed srng lists In a number of cases we see kernel panics on resume due to ath11k kernel page fault, which happens under the following circumstances: 1) First ath11k_hal_dump_srng_stats() call Last interrupt received for each group: ath11k_pci 0000:01:00.0: group_id 0 22511ms before ath11k_pci 0000:01:00.0: group_id 1 14440788ms before [..] ath11k_pci 0000:01:00.0: failed to receive control response completion, polling.. ath11k_pci 0000:01:00.0: Service connect timeout ath11k_pci 0000:01:00.0: failed to connect to HTT: -110 ath11k_pci 0000:01:00.0: failed to start core: -110 ath11k_pci 0000:01:00.0: firmware crashed: MHI_CB_EE_RDDM ath11k_pci 0000:01:00.0: already resetting count 2 ath11k_pci 0000:01:00.0: failed to wait wlan mode request (mode 4): -110 ath11k_pci 0000:01:00.0: qmi failed to send wlan mode off: -110 ath11k_pci 0000:01:00.0: failed to reconfigure driver on crash recovery [..] 2) At this point reconfiguration fails (we have 2 resets) and ath11k_core_reconfigure_on_crash() calls ath11k_hal_srng_deinit() which destroys srng lists. However, it does not reset per-list ->initialized flag. 3) Second ath11k_hal_dump_srng_stats() call sees stale ->initialized flag and attempts to dump srng stats: Last interrupt received for each group: ath11k_pci 0000:01:00.0: group_id 0 66785ms before ath11k_pci 0000:01:00.0: group_id 1 14485062ms before ath11k_pci 0000:01:00.0: group_id 2 14485062ms before ath11k_pci 0000:01:00.0: group_id 3 14485062ms before ath11k_pci 0000:01:00.0: group_id 4 14780845ms before ath11k_pci 0000:01:00.0: group_id 5 14780845ms before ath11k_pci 0000:01:00.0: group_id 6 14485062ms before ath11k_pci 0000:01:00.0: group_id 7 66814ms before ath11k_pci 0000:01:00.0: group_id 8 68997ms before ath11k_pci 0000:01:00.0: group_id 9 67588ms before ath11k_pci 0000:01:00.0: group_id 10 69511ms before BUG: unable to handle page fault for address: ffffa007404eb010 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 100000067 P4D 100000067 PUD 10022d067 PMD 100b01067 PTE 0 Oops: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k] Call Trace: <TASK> ? __die_body+0xae/0xb0 ? page_fault_oops+0x381/0x3e0 ? exc_page_fault+0x69/0xa0 ? asm_exc_page_fault+0x22/0x30 ? ath11k_hal_dump_srng_stats+0x2b4/0x3b0 [ath11k (HASH:6cea 4)] ath11k_qmi_driver_event_work+0xbd/0x1050 [ath11k (HASH:6cea 4)] worker_thread+0x389/0x930 kthread+0x149/0x170 Clear per-list ->initialized flag in ath11k_hal_srng_deinit().

In the Linux kernel, the following vulnerability has been resolved: ASoC: qcom: q6apm-lpass-dais: Fix NULL pointer dereference if source graph failed If earlier opening of source graph fails (e.g. ADSP rejects due to incorrect audioreach topology), the graph is closed and "dai_data->graph[dai->id]" is assigned NULL. Preparing the DAI for sink graph continues though and next call to q6apm_lpass_dai_prepare() receives dai_data->graph[dai->id]=NULL leading to NULL pointer exception: qcom-apm gprsvc:service:2:1: Error (1) Processing 0x01001002 cmd qcom-apm gprsvc:service:2:1: DSP returned error[1001002] 1 q6apm-lpass-dais 30000000.remoteproc:glink-edge:gpr:service@1:bedais: fail to start APM port 78 q6apm-lpass-dais 30000000.remoteproc:glink-edge:gpr:service@1:bedais: ASoC: error at snd_soc_pcm_dai_prepare on TX_CODEC_DMA_TX_3: -22 Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a8 ... Call trace: q6apm_graph_media_format_pcm+0x48/0x120 (P) q6apm_lpass_dai_prepare+0x110/0x1b4 snd_soc_pcm_dai_prepare+0x74/0x108 __soc_pcm_prepare+0x44/0x160 dpcm_be_dai_prepare+0x124/0x1c0

In the Linux kernel, the following vulnerability has been resolved: io_uring/kbuf: fix signedness in this_len calculation When importing and using buffers, buf->len is considered unsigned. However, buf->len is converted to signed int when committing. This can lead to unexpected behavior if the buffer is large enough to be interpreted as a negative value. Make min_t calculation unsigned.

In the Linux kernel, the following vulnerability has been resolved: clk: davinci: Add NULL check in davinci_lpsc_clk_register() devm_kasprintf() returns NULL when memory allocation fails. Currently, davinci_lpsc_clk_register() does not check for this case, which results in a NULL pointer dereference. Add NULL check after devm_kasprintf() to prevent this issue and ensuring no resources are left allocated.

In the Linux kernel, the following vulnerability has been resolved: md: fix resync softlockup when bitmap size is less than array size Is is reported that for dm-raid10, lvextend + lvchange --syncaction will trigger following softlockup: kernel:watchdog: BUG: soft lockup - CPU#3 stuck for 26s! [mdX_resync:6976] CPU: 7 PID: 3588 Comm: mdX_resync Kdump: loaded Not tainted 6.9.0-rc4-next-20240419 #1 RIP: 0010:_raw_spin_unlock_irq+0x13/0x30 Call Trace: <TASK> md_bitmap_start_sync+0x6b/0xf0 raid10_sync_request+0x25c/0x1b40 [raid10] md_do_sync+0x64b/0x1020 md_thread+0xa7/0x170 kthread+0xcf/0x100 ret_from_fork+0x30/0x50 ret_from_fork_asm+0x1a/0x30 And the detailed process is as follows: md_do_sync j = mddev->resync_min while (j < max_sectors) sectors = raid10_sync_request(mddev, j, &skipped) if (!md_bitmap_start_sync(..., &sync_blocks)) // md_bitmap_start_sync set sync_blocks to 0 return sync_blocks + sectors_skippe; // sectors = 0; j += sectors; // j never change Root cause is that commit 301867b1c168 ("md/raid10: check slab-out-of-bounds in md_bitmap_get_counter") return early from md_bitmap_get_counter(), without setting returned blocks. Fix this problem by always set returned blocks from md_bitmap_get_counter"(), as it used to be. Noted that this patch just fix the softlockup problem in kernel, the case that bitmap size doesn't match array size still need to be fixed.

In the Linux kernel, the following vulnerability has been resolved: media: mt9m114: Fix deadlock in get_frame_interval/set_frame_interval Getting / Setting the frame interval using the V4L2 subdev pad ops get_frame_interval/set_frame_interval causes a deadlock, as the subdev state is locked in the [1] but also in the driver itself. In [2] it's described that the caller is responsible to acquire and release the lock in this case. Therefore, acquiring the lock in the driver is wrong. Remove the lock acquisitions/releases from mt9m114_ifp_get_frame_interval() and mt9m114_ifp_set_frame_interval(). [1] drivers/media/v4l2-core/v4l2-subdev.c - line 1129 [2] Documentation/driver-api/media/v4l2-subdev.rst

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7996: add missing check for rx wcid entries Non-station wcid entries must not be passed to the rx functions. In case of the global wcid entry, it could even lead to corruption in the wcid array due to pointer being casted to struct mt7996_sta_link using container_of.

In the Linux kernel, the following vulnerability has been resolved: ppp: fix memory leak in pad_compress_skb If alloc_skb() fails in pad_compress_skb(), it returns NULL without releasing the old skb. The caller does: skb = pad_compress_skb(ppp, skb); if (!skb) goto drop; drop: kfree_skb(skb); When pad_compress_skb() returns NULL, the reference to the old skb is lost and kfree_skb(skb) ends up doing nothing, leading to a memory leak. Align pad_compress_skb() semantics with realloc(): only free the old skb if allocation and compression succeed. At the call site, use the new_skb variable so the original skb is not lost when pad_compress_skb() fails.

In the Linux kernel, the following vulnerability has been resolved: power: supply: cpcap-charger: Fix null check for power_supply_get_by_name In the cpcap_usb_detect() function, the power_supply_get_by_name() function may return `NULL` instead of an error pointer. To prevent potential null pointer dereferences, Added a null check.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix a Null pointer dereference vulnerability [Why] A null pointer dereference vulnerability exists in the AMD display driver's (DC module) cleanup function dc_destruct(). When display control context (dc->ctx) construction fails (due to memory allocation failure), this pointer remains NULL. During subsequent error handling when dc_destruct() is called, there's no NULL check before dereferencing the perf_trace member (dc->ctx->perf_trace), causing a kernel null pointer dereference crash. [How] Check if dc->ctx is non-NULL before dereferencing. (Updated commit text and removed unnecessary error message) (cherry picked from commit 9dd8e2ba268c636c240a918e0a31e6feaee19404)

In the Linux kernel, the following vulnerability has been resolved: mm/memory-failure: fix handling of dissolved but not taken off from buddy pages When I did memory failure tests recently, below panic occurs: page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x8cee00 flags: 0x6fffe0000000000(node=1|zone=2|lastcpupid=0x7fff) raw: 06fffe0000000000 dead000000000100 dead000000000122 0000000000000000 raw: 0000000000000000 0000000000000009 00000000ffffffff 0000000000000000 page dumped because: VM_BUG_ON_PAGE(!PageBuddy(page)) ------------[ cut here ]------------ kernel BUG at include/linux/page-flags.h:1009! invalid opcode: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:__del_page_from_free_list+0x151/0x180 RSP: 0018:ffffa49c90437998 EFLAGS: 00000046 RAX: 0000000000000035 RBX: 0000000000000009 RCX: ffff8dd8dfd1c9c8 RDX: 0000000000000000 RSI: 0000000000000027 RDI: ffff8dd8dfd1c9c0 RBP: ffffd901233b8000 R08: ffffffffab5511f8 R09: 0000000000008c69 R10: 0000000000003c15 R11: ffffffffab5511f8 R12: ffff8dd8fffc0c80 R13: 0000000000000001 R14: ffff8dd8fffc0c80 R15: 0000000000000009 FS: 00007ff916304740(0000) GS:ffff8dd8dfd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055eae50124c8 CR3: 00000008479e0000 CR4: 00000000000006f0 Call Trace: <TASK> __rmqueue_pcplist+0x23b/0x520 get_page_from_freelist+0x26b/0xe40 __alloc_pages_noprof+0x113/0x1120 __folio_alloc_noprof+0x11/0xb0 alloc_buddy_hugetlb_folio.isra.0+0x5a/0x130 __alloc_fresh_hugetlb_folio+0xe7/0x140 alloc_pool_huge_folio+0x68/0x100 set_max_huge_pages+0x13d/0x340 hugetlb_sysctl_handler_common+0xe8/0x110 proc_sys_call_handler+0x194/0x280 vfs_write+0x387/0x550 ksys_write+0x64/0xe0 do_syscall_64+0xc2/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7ff916114887 RSP: 002b:00007ffec8a2fd78 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 000055eae500e350 RCX: 00007ff916114887 RDX: 0000000000000004 RSI: 000055eae500e390 RDI: 0000000000000003 RBP: 000055eae50104c0 R08: 0000000000000000 R09: 000055eae50104c0 R10: 0000000000000077 R11: 0000000000000246 R12: 0000000000000004 R13: 0000000000000004 R14: 00007ff916216b80 R15: 00007ff916216a00 </TASK> Modules linked in: mce_inject hwpoison_inject ---[ end trace 0000000000000000 ]--- And before the panic, there had an warning about bad page state: BUG: Bad page state in process page-types pfn:8cee00 page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x8cee00 flags: 0x6fffe0000000000(node=1|zone=2|lastcpupid=0x7fff) page_type: 0xffffff7f(buddy) raw: 06fffe0000000000 ffffd901241c0008 ffffd901240f8008 0000000000000000 raw: 0000000000000000 0000000000000009 00000000ffffff7f 0000000000000000 page dumped because: nonzero mapcount Modules linked in: mce_inject hwpoison_inject CPU: 8 PID: 154211 Comm: page-types Not tainted 6.9.0-rc4-00499-g5544ec3178e2-dirty #22 Call Trace: <TASK> dump_stack_lvl+0x83/0xa0 bad_page+0x63/0xf0 free_unref_page+0x36e/0x5c0 unpoison_memory+0x50b/0x630 simple_attr_write_xsigned.constprop.0.isra.0+0xb3/0x110 debugfs_attr_write+0x42/0x60 full_proxy_write+0x5b/0x80 vfs_write+0xcd/0x550 ksys_write+0x64/0xe0 do_syscall_64+0xc2/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f189a514887 RSP: 002b:00007ffdcd899718 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f189a514887 RDX: 0000000000000009 RSI: 00007ffdcd899730 RDI: 0000000000000003 RBP: 00007ffdcd8997a0 R08: 0000000000000000 R09: 00007ffdcd8994b2 R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffdcda199a8 R13: 0000000000404af1 R14: 000000000040ad78 R15: 00007f189a7a5040 </TASK> The root cause should be the below race: memory_failure try_memory_failure_hugetlb me_huge_page __page_handle_poison dissolve_free_hugetlb_folio drain_all_pages -- Buddy page can be isolated e.g. for compaction. take_page_off_buddy -- Failed as page is not in the ---truncated---

In the Linux kernel, the following vulnerability has been resolved: pinctrl: canaan: k230: Fix order of DT parse and pinctrl register Move DT parse before pinctrl register. This ensures that device tree parsing is done before calling devm_pinctrl_register() to prevent using uninitialized pin resources.

In the Linux kernel, the following vulnerability has been resolved: netfilter: ctnetlink: remove refcounting in expectation dumpers Same pattern as previous patch: do not keep the expectation object alive via refcount, only store a cookie value and then use that as the skip hint for dump resumption. AFAICS this has the same issue as the one resolved in the conntrack dumper, when we do if (!refcount_inc_not_zero(&exp->use)) to increment the refcount, there is a chance that exp == last, which causes a double-increment of the refcount and subsequent memory leak.

An issue was discovered in the Linux kernel brcm_nvram_parse in drivers/nvmem/brcm_nvram.c. Lacks for the check of the return value of kzalloc() can cause the NULL Pointer Dereference.

In the Linux kernel, the following vulnerability has been resolved: PCI: Fix link speed calculation on retrain failure When pcie_failed_link_retrain() fails to retrain, it tries to revert to the previous link speed. However it calculates that speed from the Link Control 2 register without masking out non-speed bits first. PCIE_LNKCTL2_TLS2SPEED() converts such incorrect values to PCI_SPEED_UNKNOWN (0xff), which in turn causes a WARN splat in pcie_set_target_speed(): pci 0000:00:01.1: [1022:14ed] type 01 class 0x060400 PCIe Root Port pci 0000:00:01.1: broken device, retraining non-functional downstream link at 2.5GT/s pci 0000:00:01.1: retraining failed WARNING: CPU: 1 PID: 1 at drivers/pci/pcie/bwctrl.c:168 pcie_set_target_speed RDX: 0000000000000001 RSI: 00000000000000ff RDI: ffff9acd82efa000 pcie_failed_link_retrain pci_device_add pci_scan_single_device Mask out the non-speed bits in PCIE_LNKCTL2_TLS2SPEED() and PCIE_LNKCAP_SLS2SPEED() so they don't incorrectly return PCI_SPEED_UNKNOWN. [bhelgaas: commit log, add details from https://lore.kernel.org/r/1c92ef6bcb314ee6977839b46b393282e4f52e74.1750684771.git.lukas@wunner.de]

In the Linux kernel, the following vulnerability has been resolved: vxlan: Fix NPD when refreshing an FDB entry with a nexthop object VXLAN FDB entries can point to either a remote destination or an FDB nexthop group. The latter is usually used in EVPN deployments where learning is disabled. However, when learning is enabled, an incoming packet might try to refresh an FDB entry that points to an FDB nexthop group and therefore does not have a remote. Such packets should be dropped, but they are only dropped after dereferencing the non-existent remote, resulting in a NPD [1] which can be reproduced using [2]. Fix by dropping such packets earlier. Remove the misleading comment from first_remote_rcu(). [1] BUG: kernel NULL pointer dereference, address: 0000000000000000 [...] CPU: 13 UID: 0 PID: 361 Comm: mausezahn Not tainted 6.17.0-rc1-virtme-g9f6b606b6b37 #1 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014 RIP: 0010:vxlan_snoop+0x98/0x1e0 [...] Call Trace: <TASK> vxlan_encap_bypass+0x209/0x240 encap_bypass_if_local+0xb1/0x100 vxlan_xmit_one+0x1375/0x17e0 vxlan_xmit+0x6b4/0x15f0 dev_hard_start_xmit+0x5d/0x1c0 __dev_queue_xmit+0x246/0xfd0 packet_sendmsg+0x113a/0x1850 __sock_sendmsg+0x38/0x70 __sys_sendto+0x126/0x180 __x64_sys_sendto+0x24/0x30 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x4b/0x53 [2] #!/bin/bash ip address add 192.0.2.1/32 dev lo ip address add 192.0.2.2/32 dev lo ip nexthop add id 1 via 192.0.2.3 fdb ip nexthop add id 10 group 1 fdb ip link add name vx0 up type vxlan id 10010 local 192.0.2.1 dstport 12345 localbypass ip link add name vx1 up type vxlan id 10020 local 192.0.2.2 dstport 54321 learning bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 192.0.2.2 port 54321 vni 10020 bridge fdb add 00:aa:bb:cc:dd:ee dev vx1 self static nhid 10 mausezahn vx0 -a 00:aa:bb:cc:dd:ee -b 00:11:22:33:44:55 -c 1 -q

In the Linux kernel, the following vulnerability has been resolved: spi: stm32: Check for cfg availability in stm32_spi_probe The stm32_spi_probe function now includes a check to ensure that the pointer returned by of_device_get_match_data is not NULL before accessing its members. This resolves a warning where a potential NULL pointer dereference could occur when accessing cfg->has_device_mode. Before accessing the 'has_device_mode' member, we verify that 'cfg' is not NULL. If 'cfg' is NULL, an error message is logged. This change ensures that the driver does not attempt to access configuration data if it is not available, thus preventing a potential system crash due to a NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: clk: samsung: Fix UBSAN panic in samsung_clk_init() With UBSAN_ARRAY_BOUNDS=y, I'm hitting the below panic due to dereferencing `ctx->clk_data.hws` before setting `ctx->clk_data.num = nr_clks`. Move that up to fix the crash. UBSAN: array index out of bounds: 00000000f2005512 [#1] PREEMPT SMP <snip> Call trace: samsung_clk_init+0x110/0x124 (P) samsung_clk_init+0x48/0x124 (L) samsung_cmu_register_one+0x3c/0xa0 exynos_arm64_register_cmu+0x54/0x64 __gs101_cmu_top_of_clk_init_declare+0x28/0x60 ...

In the Linux kernel, the following vulnerability has been resolved: net: wwan: t7xx: Fix FSM command timeout issue When driver processes the internal state change command, it use an asynchronous thread to process the command operation. If the main thread detects that the task has timed out, the asynchronous thread will panic when executing the completion notification because the main thread completion object has been released. BUG: unable to handle page fault for address: fffffffffffffff8 PGD 1f283a067 P4D 1f283a067 PUD 1f283c067 PMD 0 Oops: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:complete_all+0x3e/0xa0 [...] Call Trace: <TASK> ? __die_body+0x68/0xb0 ? page_fault_oops+0x379/0x3e0 ? exc_page_fault+0x69/0xa0 ? asm_exc_page_fault+0x22/0x30 ? complete_all+0x3e/0xa0 fsm_main_thread+0xa3/0x9c0 [mtk_t7xx (HASH:1400 5)] ? __pfx_autoremove_wake_function+0x10/0x10 kthread+0xd8/0x110 ? __pfx_fsm_main_thread+0x10/0x10 [mtk_t7xx (HASH:1400 5)] ? __pfx_kthread+0x10/0x10 ret_from_fork+0x38/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> [...] CR2: fffffffffffffff8 ---[ end trace 0000000000000000 ]--- Use the reference counter to ensure safe release as Sergey suggests: https://lore.kernel.org/all/da90f64c-260a-4329-87bf-1f9ff20a5951@gmail.com/

In the Linux kernel, the following vulnerability has been resolved: ceph: fix crash after fscrypt_encrypt_pagecache_blocks() error The function move_dirty_folio_in_page_array() was created by commit ce80b76dd327 ("ceph: introduce ceph_process_folio_batch() method") by moving code from ceph_writepages_start() to this function. This new function is supposed to return an error code which is checked by the caller (now ceph_process_folio_batch()), and on error, the caller invokes redirty_page_for_writepage() and then breaks from the loop. However, the refactoring commit has gone wrong, and it by accident, it always returns 0 (= success) because it first NULLs the pointer and then returns PTR_ERR(NULL) which is always 0. This means errors are silently ignored, leaving NULL entries in the page array, which may later crash the kernel. The simple solution is to call PTR_ERR() before clearing the pointer.

In the Linux kernel, the following vulnerability has been resolved: um: Add winch to winch_handlers before registering winch IRQ Registering a winch IRQ is racy, an interrupt may occur before the winch is added to the winch_handlers list. If that happens, register_winch_irq() adds to that list a winch that is scheduled to be (or has already been) freed, causing a panic later in winch_cleanup(). Avoid the race by adding the winch to the winch_handlers list before registering the IRQ, and rolling back if um_request_irq() fails.

In the Linux kernel, the following vulnerability has been resolved: libbpf: Prevent null-pointer dereference when prog to load has no BTF In bpf_objec_load_prog(), there's no guarantee that obj->btf is non-NULL when passing it to btf__fd(), and this function does not perform any check before dereferencing its argument (as bpf_object__btf_fd() used to do). As a consequence, we get segmentation fault errors in bpftool (for example) when trying to load programs that come without BTF information. v2: Keep btf__fd() in the fix instead of reverting to bpf_object__btf_fd().

In the Linux kernel, the following vulnerability has been resolved: igc: don't fail igc_probe() on LED setup error When igc_led_setup() fails, igc_probe() fails and triggers kernel panic in free_netdev() since unregister_netdev() is not called. [1] This behavior can be tested using fault-injection framework, especially the failslab feature. [2] Since LED support is not mandatory, treat LED setup failures as non-fatal and continue probe with a warning message, consequently avoiding the kernel panic. [1] kernel BUG at net/core/dev.c:12047! Oops: invalid opcode: 0000 [#1] SMP NOPTI CPU: 0 UID: 0 PID: 937 Comm: repro-igc-led-e Not tainted 6.17.0-rc4-enjuk-tnguy-00865-gc4940196ab02 #64 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:free_netdev+0x278/0x2b0 [...] Call Trace: <TASK> igc_probe+0x370/0x910 local_pci_probe+0x3a/0x80 pci_device_probe+0xd1/0x200 [...] [2] #!/bin/bash -ex FAILSLAB_PATH=/sys/kernel/debug/failslab/ DEVICE=0000:00:05.0 START_ADDR=$(grep " igc_led_setup" /proc/kallsyms \ | awk '{printf("0x%s", $1)}') END_ADDR=$(printf "0x%x" $((START_ADDR + 0x100))) echo $START_ADDR > $FAILSLAB_PATH/require-start echo $END_ADDR > $FAILSLAB_PATH/require-end echo 1 > $FAILSLAB_PATH/times echo 100 > $FAILSLAB_PATH/probability echo N > $FAILSLAB_PATH/ignore-gfp-wait echo $DEVICE > /sys/bus/pci/drivers/igc/bind

In the Linux kernel, the following vulnerability has been resolved: nvmet: pci-epf: Do not complete commands twice if nvmet_req_init() fails Have nvmet_req_init() and req->execute() complete failed commands. Description of the problem: nvmet_req_init() calls __nvmet_req_complete() internally upon failure, e.g., unsupported opcode, which calls the "queue_response" callback, this results in nvmet_pci_epf_queue_response() being called, which will call nvmet_pci_epf_complete_iod() if data_len is 0 or if dma_dir is different from DMA_TO_DEVICE. This results in a double completion as nvmet_pci_epf_exec_iod_work() also calls nvmet_pci_epf_complete_iod() when nvmet_req_init() fails. Steps to reproduce: On the host send a command with an unsupported opcode with nvme-cli, For example the admin command "security receive" $ sudo nvme security-recv /dev/nvme0n1 -n1 -x4096 This triggers a double completion as nvmet_req_init() fails and nvmet_pci_epf_queue_response() is called, here iod->dma_dir is still in the default state of "DMA_NONE" as set by default in nvmet_pci_epf_alloc_iod(), so nvmet_pci_epf_complete_iod() is called. Because nvmet_req_init() failed nvmet_pci_epf_complete_iod() is also called in nvmet_pci_epf_exec_iod_work() leading to a double completion. This not only sends two completions to the host but also corrupts the state of the PCI NVMe target leading to kernel oops. This patch lets nvmet_req_init() and req->execute() complete all failed commands, and removes the double completion case in nvmet_pci_epf_exec_iod_work() therefore fixing the edge cases where double completions occurred.

In the Linux kernel, the following vulnerability has been resolved: btrfs: subpage: keep TOWRITE tag until folio is cleaned btrfs_subpage_set_writeback() calls folio_start_writeback() the first time a folio is written back, and it also clears the PAGECACHE_TAG_TOWRITE tag even if there are still dirty blocks in the folio. This can break ordering guarantees, such as those required by btrfs_wait_ordered_extents(). That ordering breakage leads to a real failure. For example, running generic/464 on a zoned setup will hit the following ASSERT. This happens because the broken ordering fails to flush existing dirty pages before the file size is truncated. assertion failed: !list_empty(&ordered->list) :: 0, in fs/btrfs/zoned.c:1899 ------------[ cut here ]------------ kernel BUG at fs/btrfs/zoned.c:1899! Oops: invalid opcode: 0000 [#1] SMP NOPTI CPU: 2 UID: 0 PID: 1906169 Comm: kworker/u130:2 Kdump: loaded Not tainted 6.16.0-rc6-BTRFS-ZNS+ #554 PREEMPT(voluntary) Hardware name: Supermicro Super Server/H12SSL-NT, BIOS 2.0 02/22/2021 Workqueue: btrfs-endio-write btrfs_work_helper [btrfs] RIP: 0010:btrfs_finish_ordered_zoned.cold+0x50/0x52 [btrfs] RSP: 0018:ffffc9002efdbd60 EFLAGS: 00010246 RAX: 000000000000004c RBX: ffff88811923c4e0 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff827e38b1 RDI: 00000000ffffffff RBP: ffff88810005d000 R08: 00000000ffffdfff R09: ffffffff831051c8 R10: ffffffff83055220 R11: 0000000000000000 R12: ffff8881c2458c00 R13: ffff88811923c540 R14: ffff88811923c5e8 R15: ffff8881c1bd9680 FS: 0000000000000000(0000) GS:ffff88a04acd0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f907c7a918c CR3: 0000000004024000 CR4: 0000000000350ef0 Call Trace: <TASK> ? srso_return_thunk+0x5/0x5f btrfs_finish_ordered_io+0x4a/0x60 [btrfs] btrfs_work_helper+0xf9/0x490 [btrfs] process_one_work+0x204/0x590 ? srso_return_thunk+0x5/0x5f worker_thread+0x1d6/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0x118/0x230 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x205/0x260 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Consider process A calling writepages() with WB_SYNC_NONE. In zoned mode or for compressed writes, it locks several folios for delalloc and starts writing them out. Let's call the last locked folio folio X. Suppose the write range only partially covers folio X, leaving some pages dirty. Process A calls btrfs_subpage_set_writeback() when building a bio. This function call clears the TOWRITE tag of folio X, whose size = 8K and the block size = 4K. It is following state. 0 4K 8K |/////|/////| (flag: DIRTY, tag: DIRTY) <-----> Process A will write this range. Now suppose process B concurrently calls writepages() with WB_SYNC_ALL. It calls tag_pages_for_writeback() to tag dirty folios with PAGECACHE_TAG_TOWRITE. Since folio X is still dirty, it gets tagged. Then, B collects tagged folios using filemap_get_folios_tag() and must wait for folio X to be written before returning from writepages(). 0 4K 8K |/////|/////| (flag: DIRTY, tag: DIRTY|TOWRITE) However, between tagging and collecting, process A may call btrfs_subpage_set_writeback() and clear folio X's TOWRITE tag. 0 4K 8K | |/////| (flag: DIRTY|WRITEBACK, tag: DIRTY) As a result, process B won't see folio X in its batch, and returns without waiting for it. This breaks the WB_SYNC_ALL ordering requirement. Fix this by using btrfs_subpage_set_writeback_keepwrite(), which retains the TOWRITE tag. We now manually clear the tag only after the folio becomes clean, via the xas operation.

In the Linux kernel, the following vulnerability has been resolved: serial: 8250: fix panic due to PSLVERR When the PSLVERR_RESP_EN parameter is set to 1, the device generates an error response if an attempt is made to read an empty RBR (Receive Buffer Register) while the FIFO is enabled. In serial8250_do_startup(), calling serial_port_out(port, UART_LCR, UART_LCR_WLEN8) triggers dw8250_check_lcr(), which invokes dw8250_force_idle() and serial8250_clear_and_reinit_fifos(). The latter function enables the FIFO via serial_out(p, UART_FCR, p->fcr). Execution proceeds to the serial_port_in(port, UART_RX). This satisfies the PSLVERR trigger condition. When another CPU (e.g., using printk()) is accessing the UART (UART is busy), the current CPU fails the check (value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR) in dw8250_check_lcr(), causing it to enter dw8250_force_idle(). Put serial_port_out(port, UART_LCR, UART_LCR_WLEN8) under the port->lock to fix this issue. Panic backtrace: [ 0.442336] Oops - unknown exception [#1] [ 0.442343] epc : dw8250_serial_in32+0x1e/0x4a [ 0.442351] ra : serial8250_do_startup+0x2c8/0x88e ... [ 0.442416] console_on_rootfs+0x26/0x70

In the Linux kernel, the following vulnerability has been resolved: clk: sunxi-ng: mp: Fix dual-divider clock rate readback When dual-divider clock support was introduced, the P divider offset was left out of the .recalc_rate readback function. This causes the clock rate to become bogus or even zero (possibly due to the P divider being 1, leading to a divide-by-zero). Fix this by incorporating the P divider offset into the calculation.

In the Linux kernel, the following vulnerability has been resolved: block: refine the EOF check in blkdev_iomap_begin blkdev_iomap_begin rounds down the offset to the logical block size before stashing it in iomap->offset and checking that it still is inside the inode size. Check the i_size check to the raw pos value so that we don't try a zero size write if iter->pos is unaligned.

In the Linux kernel, the following vulnerability has been resolved: platform/x86: alienware-wmi-wmax: Fix `dmi_system_id` array Add missing empty member to `awcc_dmi_table`.

In the Linux kernel, the following vulnerability has been resolved: macintosh/via-macii: Fix "BUG: sleeping function called from invalid context" The via-macii ADB driver calls request_irq() after disabling hard interrupts. But disabling interrupts isn't necessary here because the VIA shift register interrupt was masked during VIA1 initialization.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/migrate: prevent infinite recursion If the buf + offset is not aligned to XE_CAHELINE_BYTES we fallback to using a bounce buffer. However the bounce buffer here is allocated on the stack, and the only alignment requirement here is that it's naturally aligned to u8, and not XE_CACHELINE_BYTES. If the bounce buffer is also misaligned we then recurse back into the function again, however the new bounce buffer might also not be aligned, and might never be until we eventually blow through the stack, as we keep recursing. Instead of using the stack use kmalloc, which should respect the power-of-two alignment request here. Fixes a kernel panic when triggering this path through eudebug. v2 (Stuart): - Add build bug check for power-of-two restriction - s/EINVAL/ENOMEM/ (cherry picked from commit 38b34e928a08ba594c4bbf7118aa3aadacd62fff)

In the Linux kernel, the following vulnerability has been resolved: blk-cgroup: fix list corruption from resetting io stat Since commit 3b8cc6298724 ("blk-cgroup: Optimize blkcg_rstat_flush()"), each iostat instance is added to blkcg percpu list, so blkcg_reset_stats() can't reset the stat instance by memset(), otherwise the llist may be corrupted. Fix the issue by only resetting the counter part.

In the Linux kernel, the following vulnerability has been resolved: rcutorture: Fix rcutorture_one_extend_check() splat in RT kernels For built with CONFIG_PREEMPT_RT=y kernels, running rcutorture tests resulted in the following splat: [ 68.797425] rcutorture_one_extend_check during change: Current 0x1 To add 0x1 To remove 0x0 preempt_count() 0x0 [ 68.797533] WARNING: CPU: 2 PID: 512 at kernel/rcu/rcutorture.c:1993 rcutorture_one_extend_check+0x419/0x560 [rcutorture] [ 68.797601] Call Trace: [ 68.797602] <TASK> [ 68.797619] ? lockdep_softirqs_off+0xa5/0x160 [ 68.797631] rcutorture_one_extend+0x18e/0xcc0 [rcutorture 2466dbd2ff34dbaa36049cb323a80c3306ac997c] [ 68.797646] ? local_clock+0x19/0x40 [ 68.797659] rcu_torture_one_read+0xf0/0x280 [rcutorture 2466dbd2ff34dbaa36049cb323a80c3306ac997c] [ 68.797678] ? __pfx_rcu_torture_one_read+0x10/0x10 [rcutorture 2466dbd2ff34dbaa36049cb323a80c3306ac997c] [ 68.797804] ? __pfx_rcu_torture_timer+0x10/0x10 [rcutorture 2466dbd2ff34dbaa36049cb323a80c3306ac997c] [ 68.797815] rcu-torture: rcu_torture_reader task started [ 68.797824] rcu-torture: Creating rcu_torture_reader task [ 68.797824] rcu_torture_reader+0x238/0x580 [rcutorture 2466dbd2ff34dbaa36049cb323a80c3306ac997c] [ 68.797836] ? kvm_sched_clock_read+0x15/0x30 Disable BH does not change the SOFTIRQ corresponding bits in preempt_count() for RT kernels, this commit therefore use softirq_count() to check the if BH is disabled.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Avoid a NULL pointer dereference [WHY] Although unlikely drm_atomic_get_new_connector_state() or drm_atomic_get_old_connector_state() can return NULL. [HOW] Check returns before dereference. (cherry picked from commit 1e5e8d672fec9f2ab352be121be971877bff2af9)

In the Linux kernel, the following vulnerability has been resolved: drm/hisilicon/hibmc: fix irq_request()'s irq name variable is local The local variable is passed in request_irq (), and there will be use after free problem, which will make request_irq failed. Using the global irq name instead of it to fix.

In the Linux kernel, the following vulnerability has been resolved: net: micrel: Fix receiving the timestamp in the frame for lan8841 The blamed commit started to use the ptp workqueue to get the second part of the timestamp. And when the port was set down, then this workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING is not enabled, then the ptp_clock is not initialized so then it would crash when it would try to access the delayed work. So then basically by setting up and then down the port, it would crash. The fix consists in checking if the ptp_clock is initialized and only then cancel the delayed work.

In the Linux kernel, the following vulnerability has been resolved: igb: Fix NULL pointer dereference in ethtool loopback test The igb driver currently causes a NULL pointer dereference when executing the ethtool loopback test. This occurs because there is no associated q_vector for the test ring when it is set up, as interrupts are typically not added to the test rings. Since commit 5ef44b3cb43b removed the napi_id assignment in __xdp_rxq_info_reg(), there is no longer a need to pass a napi_id to it. Therefore, simply use 0 as the last parameter.

In the Linux kernel, the following vulnerability has been resolved: ASoC: amd: acp: Fix incorrect retrival of acp_chip_info Use dev_get_drvdata(dev->parent) instead of dev_get_platdata(dev) to correctly obtain acp_chip_info members in the acp I2S driver. Previously, some members were not updated properly due to incorrect data access, which could potentially lead to null pointer dereferences. This issue was missed in the earlier commit ("ASoC: amd: acp: Fix NULL pointer deref in acp_i2s_set_tdm_slot"), which only addressed set_tdm_slot(). This change ensures that all relevant functions correctly retrieve acp_chip_info, preventing further null pointer dereference issues.