In the Linux kernel, the following vulnerability has been resolved: media: xc2028: avoid use-after-free in load_firmware_cb() syzkaller reported use-after-free in load_firmware_cb() [1]. The reason is because the module allocated a struct tuner in tuner_probe(), and then the module initialization failed, the struct tuner was released. A worker which created during module initialization accesses this struct tuner later, it caused use-after-free. The process is as follows: task-6504 worker_thread tuner_probe <= alloc dvb_frontend [2] ... request_firmware_nowait <= create a worker ... tuner_remove <= free dvb_frontend ... request_firmware_work_func <= the firmware is ready load_firmware_cb <= but now the dvb_frontend has been freed To fix the issue, check the dvd_frontend in load_firmware_cb(), if it is null, report a warning and just return. [1]: ================================================================== BUG: KASAN: use-after-free in load_firmware_cb+0x1310/0x17a0 Read of size 8 at addr ffff8000d7ca2308 by task kworker/2:3/6504 Call trace: load_firmware_cb+0x1310/0x17a0 request_firmware_work_func+0x128/0x220 process_one_work+0x770/0x1824 worker_thread+0x488/0xea0 kthread+0x300/0x430 ret_from_fork+0x10/0x20 Allocated by task 6504: kzalloc tuner_probe+0xb0/0x1430 i2c_device_probe+0x92c/0xaf0 really_probe+0x678/0xcd0 driver_probe_device+0x280/0x370 __device_attach_driver+0x220/0x330 bus_for_each_drv+0x134/0x1c0 __device_attach+0x1f4/0x410 device_initial_probe+0x20/0x30 bus_probe_device+0x184/0x200 device_add+0x924/0x12c0 device_register+0x24/0x30 i2c_new_device+0x4e0/0xc44 v4l2_i2c_new_subdev_board+0xbc/0x290 v4l2_i2c_new_subdev+0xc8/0x104 em28xx_v4l2_init+0x1dd0/0x3770 Freed by task 6504: kfree+0x238/0x4e4 tuner_remove+0x144/0x1c0 i2c_device_remove+0xc8/0x290 __device_release_driver+0x314/0x5fc device_release_driver+0x30/0x44 bus_remove_device+0x244/0x490 device_del+0x350/0x900 device_unregister+0x28/0xd0 i2c_unregister_device+0x174/0x1d0 v4l2_device_unregister+0x224/0x380 em28xx_v4l2_init+0x1d90/0x3770 The buggy address belongs to the object at ffff8000d7ca2000 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 776 bytes inside of 2048-byte region [ffff8000d7ca2000, ffff8000d7ca2800) The buggy address belongs to the page: page:ffff7fe00035f280 count:1 mapcount:0 mapping:ffff8000c001f000 index:0x0 flags: 0x7ff800000000100(slab) raw: 07ff800000000100 ffff7fe00049d880 0000000300000003 ffff8000c001f000 raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8000d7ca2200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8000d7ca2280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff8000d7ca2300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8000d7ca2380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8000d7ca2400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== [2] Actually, it is allocated for struct tuner, and dvb_frontend is inside.

In the Linux kernel, the following vulnerability has been resolved: net/iucv: fix use after free in iucv_sock_close() iucv_sever_path() is called from process context and from bh context. iucv->path is used as indicator whether somebody else is taking care of severing the path (or it is already removed / never existed). This needs to be done with atomic compare and swap, otherwise there is a small window where iucv_sock_close() will try to work with a path that has already been severed and freed by iucv_callback_connrej() called by iucv_tasklet_fn(). Example: [452744.123844] Call Trace: [452744.123845] ([<0000001e87f03880>] 0x1e87f03880) [452744.123966] [<00000000d593001e>] iucv_path_sever+0x96/0x138 [452744.124330] [<000003ff801ddbca>] iucv_sever_path+0xc2/0xd0 [af_iucv] [452744.124336] [<000003ff801e01b6>] iucv_sock_close+0xa6/0x310 [af_iucv] [452744.124341] [<000003ff801e08cc>] iucv_sock_release+0x3c/0xd0 [af_iucv] [452744.124345] [<00000000d574794e>] __sock_release+0x5e/0xe8 [452744.124815] [<00000000d5747a0c>] sock_close+0x34/0x48 [452744.124820] [<00000000d5421642>] __fput+0xba/0x268 [452744.124826] [<00000000d51b382c>] task_work_run+0xbc/0xf0 [452744.124832] [<00000000d5145710>] do_notify_resume+0x88/0x90 [452744.124841] [<00000000d5978096>] system_call+0xe2/0x2c8 [452744.125319] Last Breaking-Event-Address: [452744.125321] [<00000000d5930018>] iucv_path_sever+0x90/0x138 [452744.125324] [452744.125325] Kernel panic - not syncing: Fatal exception in interrupt Note that bh_lock_sock() is not serializing the tasklet context against process context, because the check for sock_owned_by_user() and corresponding handling is missing. Ideas for a future clean-up patch: A) Correct usage of bh_lock_sock() in tasklet context, as described in Re-enqueue, if needed. This may require adding return values to the tasklet functions and thus changes to all users of iucv. B) Change iucv tasklet into worker and use only lock_sock() in af_iucv.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Validate data run offset This adds sanity checks for data run offset. We should make sure data run offset is legit before trying to unpack them, otherwise we may encounter use-after-free or some unexpected memory access behaviors. [ 82.940342] BUG: KASAN: use-after-free in run_unpack+0x2e3/0x570 [ 82.941180] Read of size 1 at addr ffff888008a8487f by task mount/240 [ 82.941670] [ 82.942069] CPU: 0 PID: 240 Comm: mount Not tainted 5.19.0+ #15 [ 82.942482] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 [ 82.943720] Call Trace: [ 82.944204] <TASK> [ 82.944471] dump_stack_lvl+0x49/0x63 [ 82.944908] print_report.cold+0xf5/0x67b [ 82.945141] ? __wait_on_bit+0x106/0x120 [ 82.945750] ? run_unpack+0x2e3/0x570 [ 82.946626] kasan_report+0xa7/0x120 [ 82.947046] ? run_unpack+0x2e3/0x570 [ 82.947280] __asan_load1+0x51/0x60 [ 82.947483] run_unpack+0x2e3/0x570 [ 82.947709] ? memcpy+0x4e/0x70 [ 82.947927] ? run_pack+0x7a0/0x7a0 [ 82.948158] run_unpack_ex+0xad/0x3f0 [ 82.948399] ? mi_enum_attr+0x14a/0x200 [ 82.948717] ? run_unpack+0x570/0x570 [ 82.949072] ? ni_enum_attr_ex+0x1b2/0x1c0 [ 82.949332] ? ni_fname_type.part.0+0xd0/0xd0 [ 82.949611] ? mi_read+0x262/0x2c0 [ 82.949970] ? ntfs_cmp_names_cpu+0x125/0x180 [ 82.950249] ntfs_iget5+0x632/0x1870 [ 82.950621] ? ntfs_get_block_bmap+0x70/0x70 [ 82.951192] ? evict+0x223/0x280 [ 82.951525] ? iput.part.0+0x286/0x320 [ 82.951969] ntfs_fill_super+0x1321/0x1e20 [ 82.952436] ? put_ntfs+0x1d0/0x1d0 [ 82.952822] ? vsprintf+0x20/0x20 [ 82.953188] ? mutex_unlock+0x81/0xd0 [ 82.953379] ? set_blocksize+0x95/0x150 [ 82.954001] get_tree_bdev+0x232/0x370 [ 82.954438] ? put_ntfs+0x1d0/0x1d0 [ 82.954700] ntfs_fs_get_tree+0x15/0x20 [ 82.955049] vfs_get_tree+0x4c/0x130 [ 82.955292] path_mount+0x645/0xfd0 [ 82.955615] ? putname+0x80/0xa0 [ 82.955955] ? finish_automount+0x2e0/0x2e0 [ 82.956310] ? kmem_cache_free+0x110/0x390 [ 82.956723] ? putname+0x80/0xa0 [ 82.957023] do_mount+0xd6/0xf0 [ 82.957411] ? path_mount+0xfd0/0xfd0 [ 82.957638] ? __kasan_check_write+0x14/0x20 [ 82.957948] __x64_sys_mount+0xca/0x110 [ 82.958310] do_syscall_64+0x3b/0x90 [ 82.958719] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 82.959341] RIP: 0033:0x7fd0d1ce948a [ 82.960193] Code: 48 8b 0d 11 fa 2a 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 008 [ 82.961532] RSP: 002b:00007ffe59ff69a8 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5 [ 82.962527] RAX: ffffffffffffffda RBX: 0000564dcc107060 RCX: 00007fd0d1ce948a [ 82.963266] RDX: 0000564dcc107260 RSI: 0000564dcc1072e0 RDI: 0000564dcc10fce0 [ 82.963686] RBP: 0000000000000000 R08: 0000564dcc107280 R09: 0000000000000020 [ 82.964272] R10: 00000000c0ed0000 R11: 0000000000000202 R12: 0000564dcc10fce0 [ 82.964785] R13: 0000564dcc107260 R14: 0000000000000000 R15: 00000000ffffffff

In the Linux kernel, the following vulnerability has been resolved: crypto: sun8i-ce - Fix use after free in unprepare sun8i_ce_cipher_unprepare should be called before crypto_finalize_skcipher_request, because client callbacks may immediately free memory, that isn't needed anymore. But it will be used by unprepare after free. Before removing prepare/unprepare callbacks it was handled by crypto engine in crypto_finalize_request. Usually that results in a pointer dereference problem during a in crypto selftest. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000030 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=000000004716d000 [0000000000000030] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 0000000096000004 [#1] SMP This problem is detected by KASAN as well. ================================================================== BUG: KASAN: slab-use-after-free in sun8i_ce_cipher_do_one+0x6e8/0xf80 [sun8i_ce] Read of size 8 at addr ffff00000dcdc040 by task 1c15000.crypto-/373 Hardware name: Pine64 PinePhone (1.2) (DT) Call trace: dump_backtrace+0x9c/0x128 show_stack+0x20/0x38 dump_stack_lvl+0x48/0x60 print_report+0xf8/0x5d8 kasan_report+0x90/0xd0 __asan_load8+0x9c/0xc0 sun8i_ce_cipher_do_one+0x6e8/0xf80 [sun8i_ce] crypto_pump_work+0x354/0x620 [crypto_engine] kthread_worker_fn+0x244/0x498 kthread+0x168/0x178 ret_from_fork+0x10/0x20 Allocated by task 379: kasan_save_stack+0x3c/0x68 kasan_set_track+0x2c/0x40 kasan_save_alloc_info+0x24/0x38 __kasan_kmalloc+0xd4/0xd8 __kmalloc+0x74/0x1d0 alg_test_skcipher+0x90/0x1f0 alg_test+0x24c/0x830 cryptomgr_test+0x38/0x60 kthread+0x168/0x178 ret_from_fork+0x10/0x20 Freed by task 379: kasan_save_stack+0x3c/0x68 kasan_set_track+0x2c/0x40 kasan_save_free_info+0x38/0x60 __kasan_slab_free+0x100/0x170 slab_free_freelist_hook+0xd4/0x1e8 __kmem_cache_free+0x15c/0x290 kfree+0x74/0x100 kfree_sensitive+0x80/0xb0 alg_test_skcipher+0x12c/0x1f0 alg_test+0x24c/0x830 cryptomgr_test+0x38/0x60 kthread+0x168/0x178 ret_from_fork+0x10/0x20 The buggy address belongs to the object at ffff00000dcdc000 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 64 bytes inside of freed 256-byte region [ffff00000dcdc000, ffff00000dcdc100)

In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: Fix Use-After-Free in ovs_ct_exit Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal of ovs_ct_limit_exit, is not part of the RCU read critical section, it is possible that the RCU grace period will pass during the traversal and the key will be free. To prevent this, it should be changed to hlist_for_each_entry_safe.

In the Linux kernel, the following vulnerability has been resolved: PCI/DPC: Fix use-after-free on concurrent DPC and hot-removal Keith reports a use-after-free when a DPC event occurs concurrently to hot-removal of the same portion of the hierarchy: The dpc_handler() awaits readiness of the secondary bus below the Downstream Port where the DPC event occurred. To do so, it polls the config space of the first child device on the secondary bus. If that child device is concurrently removed, accesses to its struct pci_dev cause the kernel to oops. That's because pci_bridge_wait_for_secondary_bus() neglects to hold a reference on the child device. Before v6.3, the function was only called on resume from system sleep or on runtime resume. Holding a reference wasn't necessary back then because the pciehp IRQ thread could never run concurrently. (On resume from system sleep, IRQs are not enabled until after the resume_noirq phase. And runtime resume is always awaited before a PCI device is removed.) However starting with v6.3, pci_bridge_wait_for_secondary_bus() is also called on a DPC event. Commit 53b54ad074de ("PCI/DPC: Await readiness of secondary bus after reset"), which introduced that, failed to appreciate that pci_bridge_wait_for_secondary_bus() now needs to hold a reference on the child device because dpc_handler() and pciehp may indeed run concurrently. The commit was backported to v5.10+ stable kernels, so that's the oldest one affected. Add the missing reference acquisition. Abridged stack trace: BUG: unable to handle page fault for address: 00000000091400c0 CPU: 15 PID: 2464 Comm: irq/53-pcie-dpc 6.9.0 RIP: pci_bus_read_config_dword+0x17/0x50 pci_dev_wait() pci_bridge_wait_for_secondary_bus() dpc_reset_link() pcie_do_recovery() dpc_handler()

In the Linux kernel, the following vulnerability has been resolved: ftrace: Fix use-after-free for dynamic ftrace_ops KASAN reported a use-after-free with ftrace ops [1]. It was found from vmcore that perf had registered two ops with the same content successively, both dynamic. After unregistering the second ops, a use-after-free occurred. In ftrace_shutdown(), when the second ops is unregistered, the FTRACE_UPDATE_CALLS command is not set because there is another enabled ops with the same content. Also, both ops are dynamic and the ftrace callback function is ftrace_ops_list_func, so the FTRACE_UPDATE_TRACE_FUNC command will not be set. Eventually the value of 'command' will be 0 and ftrace_shutdown() will skip the rcu synchronization. However, ftrace may be activated. When the ops is released, another CPU may be accessing the ops. Add the missing synchronization to fix this problem. [1] BUG: KASAN: use-after-free in __ftrace_ops_list_func kernel/trace/ftrace.c:7020 [inline] BUG: KASAN: use-after-free in ftrace_ops_list_func+0x2b0/0x31c kernel/trace/ftrace.c:7049 Read of size 8 at addr ffff56551965bbc8 by task syz-executor.2/14468 CPU: 1 PID: 14468 Comm: syz-executor.2 Not tainted 5.10.0 #7 Hardware name: linux,dummy-virt (DT) Call trace: dump_backtrace+0x0/0x40c arch/arm64/kernel/stacktrace.c:132 show_stack+0x30/0x40 arch/arm64/kernel/stacktrace.c:196 __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1b4/0x248 lib/dump_stack.c:118 print_address_description.constprop.0+0x28/0x48c mm/kasan/report.c:387 __kasan_report mm/kasan/report.c:547 [inline] kasan_report+0x118/0x210 mm/kasan/report.c:564 check_memory_region_inline mm/kasan/generic.c:187 [inline] __asan_load8+0x98/0xc0 mm/kasan/generic.c:253 __ftrace_ops_list_func kernel/trace/ftrace.c:7020 [inline] ftrace_ops_list_func+0x2b0/0x31c kernel/trace/ftrace.c:7049 ftrace_graph_call+0x0/0x4 __might_sleep+0x8/0x100 include/linux/perf_event.h:1170 __might_fault mm/memory.c:5183 [inline] __might_fault+0x58/0x70 mm/memory.c:5171 do_strncpy_from_user lib/strncpy_from_user.c:41 [inline] strncpy_from_user+0x1f4/0x4b0 lib/strncpy_from_user.c:139 getname_flags+0xb0/0x31c fs/namei.c:149 getname+0x2c/0x40 fs/namei.c:209 [...] Allocated by task 14445: kasan_save_stack+0x24/0x50 mm/kasan/common.c:48 kasan_set_track mm/kasan/common.c:56 [inline] __kasan_kmalloc mm/kasan/common.c:479 [inline] __kasan_kmalloc.constprop.0+0x110/0x13c mm/kasan/common.c:449 kasan_kmalloc+0xc/0x14 mm/kasan/common.c:493 kmem_cache_alloc_trace+0x440/0x924 mm/slub.c:2950 kmalloc include/linux/slab.h:563 [inline] kzalloc include/linux/slab.h:675 [inline] perf_event_alloc.part.0+0xb4/0x1350 kernel/events/core.c:11230 perf_event_alloc kernel/events/core.c:11733 [inline] __do_sys_perf_event_open kernel/events/core.c:11831 [inline] __se_sys_perf_event_open+0x550/0x15f4 kernel/events/core.c:11723 __arm64_sys_perf_event_open+0x6c/0x80 kernel/events/core.c:11723 [...] Freed by task 14445: kasan_save_stack+0x24/0x50 mm/kasan/common.c:48 kasan_set_track+0x24/0x34 mm/kasan/common.c:56 kasan_set_free_info+0x20/0x40 mm/kasan/generic.c:358 __kasan_slab_free.part.0+0x11c/0x1b0 mm/kasan/common.c:437 __kasan_slab_free mm/kasan/common.c:445 [inline] kasan_slab_free+0x2c/0x40 mm/kasan/common.c:446 slab_free_hook mm/slub.c:1569 [inline] slab_free_freelist_hook mm/slub.c:1608 [inline] slab_free mm/slub.c:3179 [inline] kfree+0x12c/0xc10 mm/slub.c:4176 perf_event_alloc.part.0+0xa0c/0x1350 kernel/events/core.c:11434 perf_event_alloc kernel/events/core.c:11733 [inline] __do_sys_perf_event_open kernel/events/core.c:11831 [inline] __se_sys_perf_event_open+0x550/0x15f4 kernel/events/core.c:11723 [...]

In the Linux kernel, the following vulnerability has been resolved: ath11k: free peer for station when disconnect from AP for QCA6390/WCN6855 Commit b4a0f54156ac ("ath11k: move peer delete after vdev stop of station for QCA6390 and WCN6855") is to fix firmware crash by changing the WMI command sequence, but actually skip all the peer delete operation, then it lead commit 58595c9874c6 ("ath11k: Fixing dangling pointer issue upon peer delete failure") not take effect, and then happened a use-after-free warning from KASAN. because the peer->sta is not set to NULL and then used later. Change to only skip the WMI_PEER_DELETE_CMDID for QCA6390/WCN6855. log of user-after-free: [ 534.888665] BUG: KASAN: use-after-free in ath11k_dp_rx_update_peer_stats+0x912/0xc10 [ath11k] [ 534.888696] Read of size 8 at addr ffff8881396bb1b8 by task rtcwake/2860 [ 534.888705] CPU: 4 PID: 2860 Comm: rtcwake Kdump: loaded Tainted: G W 5.15.0-wt-ath+ #523 [ 534.888712] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0067.2021.0528.1339 05/28/2021 [ 534.888716] Call Trace: [ 534.888720] <IRQ> [ 534.888726] dump_stack_lvl+0x57/0x7d [ 534.888736] print_address_description.constprop.0+0x1f/0x170 [ 534.888745] ? ath11k_dp_rx_update_peer_stats+0x912/0xc10 [ath11k] [ 534.888771] kasan_report.cold+0x83/0xdf [ 534.888783] ? ath11k_dp_rx_update_peer_stats+0x912/0xc10 [ath11k] [ 534.888810] ath11k_dp_rx_update_peer_stats+0x912/0xc10 [ath11k] [ 534.888840] ath11k_dp_rx_process_mon_status+0x529/0xa70 [ath11k] [ 534.888874] ? ath11k_dp_rx_mon_status_bufs_replenish+0x3f0/0x3f0 [ath11k] [ 534.888897] ? check_prev_add+0x20f0/0x20f0 [ 534.888922] ? __lock_acquire+0xb72/0x1870 [ 534.888937] ? find_held_lock+0x33/0x110 [ 534.888954] ath11k_dp_rx_process_mon_rings+0x297/0x520 [ath11k] [ 534.888981] ? rcu_read_unlock+0x40/0x40 [ 534.888990] ? ath11k_dp_rx_pdev_alloc+0xd90/0xd90 [ath11k] [ 534.889026] ath11k_dp_service_mon_ring+0x67/0xe0 [ath11k] [ 534.889053] ? ath11k_dp_rx_process_mon_rings+0x520/0x520 [ath11k] [ 534.889075] call_timer_fn+0x167/0x4a0 [ 534.889084] ? add_timer_on+0x3b0/0x3b0 [ 534.889103] ? lockdep_hardirqs_on_prepare.part.0+0x18c/0x370 [ 534.889117] __run_timers.part.0+0x539/0x8b0 [ 534.889123] ? ath11k_dp_rx_process_mon_rings+0x520/0x520 [ath11k] [ 534.889157] ? call_timer_fn+0x4a0/0x4a0 [ 534.889164] ? mark_lock_irq+0x1c30/0x1c30 [ 534.889173] ? clockevents_program_event+0xdd/0x280 [ 534.889189] ? mark_held_locks+0xa5/0xe0 [ 534.889203] run_timer_softirq+0x97/0x180 [ 534.889213] __do_softirq+0x276/0x86a [ 534.889230] __irq_exit_rcu+0x11c/0x180 [ 534.889238] irq_exit_rcu+0x5/0x20 [ 534.889244] sysvec_apic_timer_interrupt+0x8e/0xc0 [ 534.889251] </IRQ> [ 534.889254] <TASK> [ 534.889259] asm_sysvec_apic_timer_interrupt+0x12/0x20 [ 534.889265] RIP: 0010:_raw_spin_unlock_irqrestore+0x38/0x70 [ 534.889271] Code: 74 24 10 e8 ea c2 bf fd 48 89 ef e8 12 53 c0 fd 81 e3 00 02 00 00 75 25 9c 58 f6 c4 02 75 2d 48 85 db 74 01 fb bf 01 00 00 00 <e8> 13 a7 b5 fd 65 8b 05 cc d9 9c 5e 85 c0 74 0a 5b 5d c3 e8 a0 ee [ 534.889276] RSP: 0018:ffffc90002e5f880 EFLAGS: 00000206 [ 534.889284] RAX: 0000000000000006 RBX: 0000000000000200 RCX: ffffffff9f256f10 [ 534.889289] RDX: 0000000000000000 RSI: ffffffffa1c6e420 RDI: 0000000000000001 [ 534.889293] RBP: ffff8881095e6200 R08: 0000000000000001 R09: ffffffffa40d2b8f [ 534.889298] R10: fffffbfff481a571 R11: 0000000000000001 R12: ffff8881095e6e68 [ 534.889302] R13: ffffc90002e5f908 R14: 0000000000000246 R15: 0000000000000000 [ 534.889316] ? mark_lock+0xd0/0x14a0 [ 534.889332] klist_next+0x1d4/0x450 [ 534.889340] ? dpm_wait_for_subordinate+0x2d0/0x2d0 [ 534.889350] device_for_each_child+0xa8/0x140 [ 534.889360] ? device_remove_class_symlinks+0x1b0/0x1b0 [ 534.889370] ? __lock_release+0x4bd/0x9f0 [ 534.889378] ? dpm_suspend+0x26b/0x3f0 [ 534.889390] dpm_wait_for_subordinate+ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: usb: cdns3 fix use-after-free at workaround 2 BUG: KFENCE: use-after-free read in __list_del_entry_valid+0x10/0xac cdns3_wa2_remove_old_request() { ... kfree(priv_req->request.buf); cdns3_gadget_ep_free_request(&priv_ep->endpoint, &priv_req->request); list_del_init(&priv_req->list); ^^^ use after free ... } cdns3_gadget_ep_free_request() free the space pointed by priv_req, but priv_req is used in the following list_del_init(). This patch move list_del_init() before cdns3_gadget_ep_free_request().

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. Due to a race condition between nf_tables netlink control plane transaction and nft_set element garbage collection, it is possible to underflow the reference counter causing a use-after-free vulnerability. We recommend upgrading past commit 3e91b0ebd994635df2346353322ac51ce84ce6d8.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix use-after-free in ext4_rename_dir_prepare We got issue as follows: EXT4-fs (loop0): mounted filesystem without journal. Opts: ,errors=continue ext4_get_first_dir_block: bh->b_data=0xffff88810bee6000 len=34478 ext4_get_first_dir_block: *parent_de=0xffff88810beee6ae bh->b_data=0xffff88810bee6000 ext4_rename_dir_prepare: [1] parent_de=0xffff88810beee6ae ================================================================== BUG: KASAN: use-after-free in ext4_rename_dir_prepare+0x152/0x220 Read of size 4 at addr ffff88810beee6ae by task rep/1895 CPU: 13 PID: 1895 Comm: rep Not tainted 5.10.0+ #241 Call Trace: dump_stack+0xbe/0xf9 print_address_description.constprop.0+0x1e/0x220 kasan_report.cold+0x37/0x7f ext4_rename_dir_prepare+0x152/0x220 ext4_rename+0xf44/0x1ad0 ext4_rename2+0x11c/0x170 vfs_rename+0xa84/0x1440 do_renameat2+0x683/0x8f0 __x64_sys_renameat+0x53/0x60 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7f45a6fc41c9 RSP: 002b:00007ffc5a470218 EFLAGS: 00000246 ORIG_RAX: 0000000000000108 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f45a6fc41c9 RDX: 0000000000000005 RSI: 0000000020000180 RDI: 0000000000000005 RBP: 00007ffc5a470240 R08: 00007ffc5a470160 R09: 0000000020000080 R10: 00000000200001c0 R11: 0000000000000246 R12: 0000000000400bb0 R13: 00007ffc5a470320 R14: 0000000000000000 R15: 0000000000000000 The buggy address belongs to the page: page:00000000440015ce refcount:0 mapcount:0 mapping:0000000000000000 index:0x1 pfn:0x10beee flags: 0x200000000000000() raw: 0200000000000000 ffffea00043ff4c8 ffffea0004325608 0000000000000000 raw: 0000000000000001 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88810beee580: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88810beee600: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff >ffff88810beee680: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff88810beee700: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88810beee780: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ================================================================== Disabling lock debugging due to kernel taint ext4_rename_dir_prepare: [2] parent_de->inode=3537895424 ext4_rename_dir_prepare: [3] dir=0xffff888124170140 ext4_rename_dir_prepare: [4] ino=2 ext4_rename_dir_prepare: ent->dir->i_ino=2 parent=-757071872 Reason is first directory entry which 'rec_len' is 34478, then will get illegal parent entry. Now, we do not check directory entry after read directory block in 'ext4_get_first_dir_block'. To solve this issue, check directory entry in 'ext4_get_first_dir_block'. [ Trigger an ext4_error() instead of just warning if the directory is missing a '.' or '..' entry. Also make sure we return an error code if the file system is corrupted. -TYT ]

In the Linux kernel, the following vulnerability has been resolved: bpf: Track subprog poke descriptors correctly and fix use-after-free Subprograms are calling map_poke_track(), but on program release there is no hook to call map_poke_untrack(). However, on program release, the aux memory (and poke descriptor table) is freed even though we still have a reference to it in the element list of the map aux data. When we run map_poke_run(), we then end up accessing free'd memory, triggering KASAN in prog_array_map_poke_run(): [...] [ 402.824689] BUG: KASAN: use-after-free in prog_array_map_poke_run+0xc2/0x34e [ 402.824698] Read of size 4 at addr ffff8881905a7940 by task hubble-fgs/4337 [ 402.824705] CPU: 1 PID: 4337 Comm: hubble-fgs Tainted: G I 5.12.0+ #399 [ 402.824715] Call Trace: [ 402.824719] dump_stack+0x93/0xc2 [ 402.824727] print_address_description.constprop.0+0x1a/0x140 [ 402.824736] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824740] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824744] kasan_report.cold+0x7c/0xd8 [ 402.824752] ? prog_array_map_poke_run+0xc2/0x34e [ 402.824757] prog_array_map_poke_run+0xc2/0x34e [ 402.824765] bpf_fd_array_map_update_elem+0x124/0x1a0 [...] The elements concerned are walked as follows: for (i = 0; i < elem->aux->size_poke_tab; i++) { poke = &elem->aux->poke_tab[i]; [...] The access to size_poke_tab is a 4 byte read, verified by checking offsets in the KASAN dump: [ 402.825004] The buggy address belongs to the object at ffff8881905a7800 which belongs to the cache kmalloc-1k of size 1024 [ 402.825008] The buggy address is located 320 bytes inside of 1024-byte region [ffff8881905a7800, ffff8881905a7c00) The pahole output of bpf_prog_aux: struct bpf_prog_aux { [...] /* --- cacheline 5 boundary (320 bytes) --- */ u32 size_poke_tab; /* 320 4 */ [...] In general, subprograms do not necessarily manage their own data structures. For example, BTF func_info and linfo are just pointers to the main program structure. This allows reference counting and cleanup to be done on the latter which simplifies their management a bit. The aux->poke_tab struct, however, did not follow this logic. The initial proposed fix for this use-after-free bug further embedded poke data tracking into the subprogram with proper reference counting. However, Daniel and Alexei questioned why we were treating these objects special; I agree, its unnecessary. The fix here removes the per subprogram poke table allocation and map tracking and instead simply points the aux->poke_tab pointer at the main programs poke table. This way, map tracking is simplified to the main program and we do not need to manage them per subprogram. This also means, bpf_prog_free_deferred(), which unwinds the program reference counting and kfrees objects, needs to ensure that we don't try to double free the poke_tab when free'ing the subprog structures. This is easily solved by NULL'ing the poke_tab pointer. The second detail is to ensure that per subprogram JIT logic only does fixups on poke_tab[] entries it owns. To do this, we add a pointer in the poke structure to point at the subprogram value so JITs can easily check while walking the poke_tab structure if the current entry belongs to the current program. The aux pointer is stable and therefore suitable for such comparison. On the jit_subprogs() error path, we omit cleaning up the poke->aux field because these are only ever referenced from the JIT side, but on error we will never make it to the JIT, so its fine to leave them dangling. Removing these pointers would complicate the error path for no reason. However, we do need to untrack all poke descriptors from the main program as otherwise they could race with the freeing of JIT memory from the subprograms. Lastly, a748c6975dea3 ("bpf: propagate poke des ---truncated---

A use-after-free vulnerability in the Linux kernel's net/sched: cls_u32 component can be exploited to achieve local privilege escalation. When u32_change() is called on an existing filter, the whole tcf_result struct is always copied into the new instance of the filter. This causes a problem when updating a filter bound to a class, as tcf_unbind_filter() is always called on the old instance in the success path, decreasing filter_cnt of the still referenced class and allowing it to be deleted, leading to a use-after-free. We recommend upgrading past commit 3044b16e7c6fe5d24b1cdbcf1bd0a9d92d1ebd81.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: fix dangling sco_conn and use-after-free in sco_sock_timeout Connecting the same socket twice consecutively in sco_sock_connect() could lead to a race condition where two sco_conn objects are created but only one is associated with the socket. If the socket is closed before the SCO connection is established, the timer associated with the dangling sco_conn object won't be canceled. As the sock object is being freed, the use-after-free problem happens when the timer callback function sco_sock_timeout() accesses the socket. Here's the call trace: dump_stack+0x107/0x163 ? refcount_inc+0x1c/ print_address_description.constprop.0+0x1c/0x47e ? refcount_inc+0x1c/0x7b kasan_report+0x13a/0x173 ? refcount_inc+0x1c/0x7b check_memory_region+0x132/0x139 refcount_inc+0x1c/0x7b sco_sock_timeout+0xb2/0x1ba process_one_work+0x739/0xbd1 ? cancel_delayed_work+0x13f/0x13f ? __raw_spin_lock_init+0xf0/0xf0 ? to_kthread+0x59/0x85 worker_thread+0x593/0x70e kthread+0x346/0x35a ? drain_workqueue+0x31a/0x31a ? kthread_bind+0x4b/0x4b ret_from_fork+0x1f/0x30

In the Linux kernel, the following vulnerability has been resolved: RDMA/cma: Ensure rdma_addr_cancel() happens before issuing more requests The FSM can run in a circle allowing rdma_resolve_ip() to be called twice on the same id_priv. While this cannot happen without going through the work, it violates the invariant that the same address resolution background request cannot be active twice. CPU 1 CPU 2 rdma_resolve_addr(): RDMA_CM_IDLE -> RDMA_CM_ADDR_QUERY rdma_resolve_ip(addr_handler) #1 process_one_req(): for #1 addr_handler(): RDMA_CM_ADDR_QUERY -> RDMA_CM_ADDR_BOUND mutex_unlock(&id_priv->handler_mutex); [.. handler still running ..] rdma_resolve_addr(): RDMA_CM_ADDR_BOUND -> RDMA_CM_ADDR_QUERY rdma_resolve_ip(addr_handler) !! two requests are now on the req_list rdma_destroy_id(): destroy_id_handler_unlock(): _destroy_id(): cma_cancel_operation(): rdma_addr_cancel() // process_one_req() self removes it spin_lock_bh(&lock); cancel_delayed_work(&req->work); if (!list_empty(&req->list)) == true ! rdma_addr_cancel() returns after process_on_req #1 is done kfree(id_priv) process_one_req(): for #2 addr_handler(): mutex_lock(&id_priv->handler_mutex); !! Use after free on id_priv rdma_addr_cancel() expects there to be one req on the list and only cancels the first one. The self-removal behavior of the work only happens after the handler has returned. This yields a situations where the req_list can have two reqs for the same "handle" but rdma_addr_cancel() only cancels the first one. The second req remains active beyond rdma_destroy_id() and will use-after-free id_priv once it inevitably triggers. Fix this by remembering if the id_priv has called rdma_resolve_ip() and always cancel before calling it again. This ensures the req_list never gets more than one item in it and doesn't cost anything in the normal flow that never uses this strange error path.

In the Linux kernel, the following vulnerability has been resolved: powerpc/pseries: Fix use after free in remove_phb_dynamic() In remove_phb_dynamic() we use &phb->io_resource, after we've called device_unregister(&host_bridge->dev). But the unregister may have freed phb, because pcibios_free_controller_deferred() is the release function for the host_bridge. If there are no outstanding references when we call device_unregister() then phb will be freed out from under us. This has gone mainly unnoticed, but with slub_debug and page_poison enabled it can lead to a crash: PID: 7574 TASK: c0000000d492cb80 CPU: 13 COMMAND: "drmgr" #0 [c0000000e4f075a0] crash_kexec at c00000000027d7dc #1 [c0000000e4f075d0] oops_end at c000000000029608 #2 [c0000000e4f07650] __bad_page_fault at c0000000000904b4 #3 [c0000000e4f076c0] do_bad_slb_fault at c00000000009a5a8 #4 [c0000000e4f076f0] data_access_slb_common_virt at c000000000008b30 Data SLB Access [380] exception frame: R0: c000000000167250 R1: c0000000e4f07a00 R2: c000000002a46100 R3: c000000002b39ce8 R4: 00000000000000c0 R5: 00000000000000a9 R6: 3894674d000000c0 R7: 0000000000000000 R8: 00000000000000ff R9: 0000000000000100 R10: 6b6b6b6b6b6b6b6b R11: 0000000000008000 R12: c00000000023da80 R13: c0000009ffd38b00 R14: 0000000000000000 R15: 000000011c87f0f0 R16: 0000000000000006 R17: 0000000000000003 R18: 0000000000000002 R19: 0000000000000004 R20: 0000000000000005 R21: 000000011c87ede8 R22: 000000011c87c5a8 R23: 000000011c87d3a0 R24: 0000000000000000 R25: 0000000000000001 R26: c0000000e4f07cc8 R27: c00000004d1cc400 R28: c0080000031d00e8 R29: c00000004d23d800 R30: c00000004d1d2400 R31: c00000004d1d2540 NIP: c000000000167258 MSR: 8000000000009033 OR3: c000000000e9f474 CTR: 0000000000000000 LR: c000000000167250 XER: 0000000020040003 CCR: 0000000024088420 MQ: 0000000000000000 DAR: 6b6b6b6b6b6b6ba3 DSISR: c0000000e4f07920 Syscall Result: fffffffffffffff2 [NIP : release_resource+56] [LR : release_resource+48] #5 [c0000000e4f07a00] release_resource at c000000000167258 (unreliable) #6 [c0000000e4f07a30] remove_phb_dynamic at c000000000105648 #7 [c0000000e4f07ab0] dlpar_remove_slot at c0080000031a09e8 [rpadlpar_io] #8 [c0000000e4f07b50] remove_slot_store at c0080000031a0b9c [rpadlpar_io] #9 [c0000000e4f07be0] kobj_attr_store at c000000000817d8c #10 [c0000000e4f07c00] sysfs_kf_write at c00000000063e504 #11 [c0000000e4f07c20] kernfs_fop_write_iter at c00000000063d868 #12 [c0000000e4f07c70] new_sync_write at c00000000054339c #13 [c0000000e4f07d10] vfs_write at c000000000546624 #14 [c0000000e4f07d60] ksys_write at c0000000005469f4 #15 [c0000000e4f07db0] system_call_exception at c000000000030840 #16 [c0000000e4f07e10] system_call_vectored_common at c00000000000c168 To avoid it, we can take a reference to the host_bridge->dev until we're done using phb. Then when we drop the reference the phb will be freed.

In the Linux kernel, the following vulnerability has been resolved: iwlwifi: fix use-after-free If no firmware was present at all (or, presumably, all of the firmware files failed to parse), we end up unbinding by calling device_release_driver(), which calls remove(), which then in iwlwifi calls iwl_drv_stop(), freeing the 'drv' struct. However the new code I added will still erroneously access it after it was freed. Set 'failure=false' in this case to avoid the access, all data was already freed anyway.

In the Linux kernel, the following vulnerability has been resolved: nvme-tcp: fix possible use-after-free in transport error_recovery work While nvme_tcp_submit_async_event_work is checking the ctrl and queue state before preparing the AER command and scheduling io_work, in order to fully prevent a race where this check is not reliable the error recovery work must flush async_event_work before continuing to destroy the admin queue after setting the ctrl state to RESETTING such that there is no race .submit_async_event and the error recovery handler itself changing the ctrl state.

In the Linux kernel, the following vulnerability has been resolved: e100: Fix possible use after free in e100_xmit_prepare In e100_xmit_prepare(), if we can't map the skb, then return -ENOMEM, so e100_xmit_frame() will return NETDEV_TX_BUSY and the upper layer will resend the skb. But the skb is already freed, which will cause UAF bug when the upper layer resends the skb. Remove the harmful free.

A use-after-free vulnerability in the Linux kernel's net/sched: cls_fw component can be exploited to achieve local privilege escalation. When fw_change() is called on an existing filter, the whole tcf_result struct is always copied into the new instance of the filter. This causes a problem when updating a filter bound to a class, as tcf_unbind_filter() is always called on the old instance in the success path, decreasing filter_cnt of the still referenced class and allowing it to be deleted, leading to a use-after-free. We recommend upgrading past commit 76e42ae831991c828cffa8c37736ebfb831ad5ec.

In the Linux kernel, the following vulnerability has been resolved: media: venus: fix use after free in vdec_close There appears to be a possible use after free with vdec_close(). The firmware will add buffer release work to the work queue through HFI callbacks as a normal part of decoding. Randomly closing the decoder device from userspace during normal decoding can incur a read after free for inst. Fix it by cancelling the work in vdec_close.

In the Linux kernel, the following vulnerability has been resolved: RDMA/iwcm: Fix a use-after-free related to destroying CM IDs iw_conn_req_handler() associates a new struct rdma_id_private (conn_id) with an existing struct iw_cm_id (cm_id) as follows: conn_id->cm_id.iw = cm_id; cm_id->context = conn_id; cm_id->cm_handler = cma_iw_handler; rdma_destroy_id() frees both the cm_id and the struct rdma_id_private. Make sure that cm_work_handler() does not trigger a use-after-free by only freeing of the struct rdma_id_private after all pending work has finished.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: cyclic allocation of msg_id to avoid reuse Reusing the msg_id after a maliciously completed reopen request may cause a read request to remain unprocessed and result in a hung, as shown below: t1 | t2 | t3 ------------------------------------------------- cachefiles_ondemand_select_req cachefiles_ondemand_object_is_close(A) cachefiles_ondemand_set_object_reopening(A) queue_work(fscache_object_wq, &info->work) ondemand_object_worker cachefiles_ondemand_init_object(A) cachefiles_ondemand_send_req(OPEN) // get msg_id 6 wait_for_completion(&req_A->done) cachefiles_ondemand_daemon_read // read msg_id 6 req_A cachefiles_ondemand_get_fd copy_to_user // Malicious completion msg_id 6 copen 6,-1 cachefiles_ondemand_copen complete(&req_A->done) // will not set the object to close // because ondemand_id && fd is valid. // ondemand_object_worker() is done // but the object is still reopening. // new open req_B cachefiles_ondemand_init_object(B) cachefiles_ondemand_send_req(OPEN) // reuse msg_id 6 process_open_req copen 6,A.size // The expected failed copen was executed successfully Expect copen to fail, and when it does, it closes fd, which sets the object to close, and then close triggers reopen again. However, due to msg_id reuse resulting in a successful copen, the anonymous fd is not closed until the daemon exits. Therefore read requests waiting for reopen to complete may trigger hung task. To avoid this issue, allocate the msg_id cyclically to avoid reusing the msg_id for a very short duration of time.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: idxd: Fix possible Use-After-Free in irq_process_work_list Use list_for_each_entry_safe() to allow iterating through the list and deleting the entry in the iteration process. The descriptor is freed via idxd_desc_complete() and there's a slight chance may cause issue for the list iterator when the descriptor is reused by another thread without it being deleted from the list.

In the Linux kernel, the following vulnerability has been resolved: misc: fastrpc: avoid double fput() on failed usercopy If the copy back to userland fails for the FASTRPC_IOCTL_ALLOC_DMA_BUFF ioctl(), we shouldn't assume that 'buf->dmabuf' is still valid. In fact, dma_buf_fd() called fd_install() before, i.e. "consumed" one reference, leaving us with none. Calling dma_buf_put() will therefore put a reference we no longer own, leading to a valid file descritor table entry for an already released 'file' object which is a straight use-after-free. Simply avoid calling dma_buf_put() and rely on the process exit code to do the necessary cleanup, if needed, i.e. if the file descriptor is still valid.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix a potential use-after-free in bpf_link_free() After commit 1a80dbcb2dba, bpf_link can be freed by link->ops->dealloc_deferred, but the code still tests and uses link->ops->dealloc afterward, which leads to a use-after-free as reported by syzbot. Actually, one of them should be sufficient, so just call one of them instead of both. Also add a WARN_ON() in case of any problematic implementation.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: mst: fix suspicious rcu usage in br_mst_set_state I converted br_mst_set_state to RCU to avoid a vlan use-after-free but forgot to change the vlan group dereference helper. Switch to vlan group RCU deref helper to fix the suspicious rcu usage warning.

A use-after-free flaw was found in the Linux kernel’s Netfilter functionality when adding a rule with NFTA_RULE_CHAIN_ID. This flaw allows a local user to crash or escalate their privileges on the system.

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Fix potential UAF by revoke of fence registers CI has been sporadically reporting the following issue triggered by igt@i915_selftest@live@hangcheck on ADL-P and similar machines: <6> [414.049203] i915: Running intel_hangcheck_live_selftests/igt_reset_evict_fence ... <6> [414.068804] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled <6> [414.068812] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled <3> [414.070354] Unable to pin Y-tiled fence; err:-4 <3> [414.071282] i915_vma_revoke_fence:301 GEM_BUG_ON(!i915_active_is_idle(&fence->active)) ... <4>[ 609.603992] ------------[ cut here ]------------ <2>[ 609.603995] kernel BUG at drivers/gpu/drm/i915/gt/intel_ggtt_fencing.c:301! <4>[ 609.604003] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI <4>[ 609.604006] CPU: 0 PID: 268 Comm: kworker/u64:3 Tainted: G U W 6.9.0-CI_DRM_14785-g1ba62f8cea9c+ #1 <4>[ 609.604008] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR4 RVP, BIOS RPLPFWI1.R00.4035.A00.2301200723 01/20/2023 <4>[ 609.604010] Workqueue: i915 __i915_gem_free_work [i915] <4>[ 609.604149] RIP: 0010:i915_vma_revoke_fence+0x187/0x1f0 [i915] ... <4>[ 609.604271] Call Trace: <4>[ 609.604273] <TASK> ... <4>[ 609.604716] __i915_vma_evict+0x2e9/0x550 [i915] <4>[ 609.604852] __i915_vma_unbind+0x7c/0x160 [i915] <4>[ 609.604977] force_unbind+0x24/0xa0 [i915] <4>[ 609.605098] i915_vma_destroy+0x2f/0xa0 [i915] <4>[ 609.605210] __i915_gem_object_pages_fini+0x51/0x2f0 [i915] <4>[ 609.605330] __i915_gem_free_objects.isra.0+0x6a/0xc0 [i915] <4>[ 609.605440] process_scheduled_works+0x351/0x690 ... In the past, there were similar failures reported by CI from other IGT tests, observed on other platforms. Before commit 63baf4f3d587 ("drm/i915/gt: Only wait for GPU activity before unbinding a GGTT fence"), i915_vma_revoke_fence() was waiting for idleness of vma->active via fence_update(). That commit introduced vma->fence->active in order for the fence_update() to be able to wait selectively on that one instead of vma->active since only idleness of fence registers was needed. But then, another commit 0d86ee35097a ("drm/i915/gt: Make fence revocation unequivocal") replaced the call to fence_update() in i915_vma_revoke_fence() with only fence_write(), and also added that GEM_BUG_ON(!i915_active_is_idle(&fence->active)) in front. No justification was provided on why we might then expect idleness of vma->fence->active without first waiting on it. The issue can be potentially caused by a race among revocation of fence registers on one side and sequential execution of signal callbacks invoked on completion of a request that was using them on the other, still processed in parallel to revocation of those fence registers. Fix it by waiting for idleness of vma->fence->active in i915_vma_revoke_fence(). (cherry picked from commit 24bb052d3dd499c5956abad5f7d8e4fd07da7fb1)

In the Linux kernel, the following vulnerability has been resolved: cachefiles: fix slab-use-after-free in fscache_withdraw_volume() We got the following issue in our fault injection stress test: ================================================================== BUG: KASAN: slab-use-after-free in fscache_withdraw_volume+0x2e1/0x370 Read of size 4 at addr ffff88810680be08 by task ondemand-04-dae/5798 CPU: 0 PID: 5798 Comm: ondemand-04-dae Not tainted 6.8.0-dirty #565 Call Trace: kasan_check_range+0xf6/0x1b0 fscache_withdraw_volume+0x2e1/0x370 cachefiles_withdraw_volume+0x31/0x50 cachefiles_withdraw_cache+0x3ad/0x900 cachefiles_put_unbind_pincount+0x1f6/0x250 cachefiles_daemon_release+0x13b/0x290 __fput+0x204/0xa00 task_work_run+0x139/0x230 Allocated by task 5820: __kmalloc+0x1df/0x4b0 fscache_alloc_volume+0x70/0x600 __fscache_acquire_volume+0x1c/0x610 erofs_fscache_register_volume+0x96/0x1a0 erofs_fscache_register_fs+0x49a/0x690 erofs_fc_fill_super+0x6c0/0xcc0 vfs_get_super+0xa9/0x140 vfs_get_tree+0x8e/0x300 do_new_mount+0x28c/0x580 [...] Freed by task 5820: kfree+0xf1/0x2c0 fscache_put_volume.part.0+0x5cb/0x9e0 erofs_fscache_unregister_fs+0x157/0x1b0 erofs_kill_sb+0xd9/0x1c0 deactivate_locked_super+0xa3/0x100 vfs_get_super+0x105/0x140 vfs_get_tree+0x8e/0x300 do_new_mount+0x28c/0x580 [...] ================================================================== Following is the process that triggers the issue: mount failed | daemon exit ------------------------------------------------------------ deactivate_locked_super cachefiles_daemon_release erofs_kill_sb erofs_fscache_unregister_fs fscache_relinquish_volume __fscache_relinquish_volume fscache_put_volume(fscache_volume, fscache_volume_put_relinquish) zero = __refcount_dec_and_test(&fscache_volume->ref, &ref); cachefiles_put_unbind_pincount cachefiles_daemon_unbind cachefiles_withdraw_cache cachefiles_withdraw_volumes list_del_init(&volume->cache_link) fscache_free_volume(fscache_volume) cache->ops->free_volume cachefiles_free_volume list_del_init(&cachefiles_volume->cache_link); kfree(fscache_volume) cachefiles_withdraw_volume fscache_withdraw_volume fscache_volume->n_accesses // fscache_volume UAF !!! The fscache_volume in cache->volumes must not have been freed yet, but its reference count may be 0. So use the new fscache_try_get_volume() helper function try to get its reference count. If the reference count of fscache_volume is 0, fscache_put_volume() is freeing it, so wait for it to be removed from cache->volumes. If its reference count is not 0, call cachefiles_withdraw_volume() with reference count protection to avoid the above issue.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: wait for ondemand_object_worker to finish when dropping object When queuing ondemand_object_worker() to re-open the object, cachefiles_object is not pinned. The cachefiles_object may be freed when the pending read request is completed intentionally and the related erofs is umounted. If ondemand_object_worker() runs after the object is freed, it will incur use-after-free problem as shown below. process A processs B process C process D cachefiles_ondemand_send_req() // send a read req X // wait for its completion // close ondemand fd cachefiles_ondemand_fd_release() // set object as CLOSE cachefiles_ondemand_daemon_read() // set object as REOPENING queue_work(fscache_wq, &info->ondemand_work) // close /dev/cachefiles cachefiles_daemon_release cachefiles_flush_reqs complete(&req->done) // read req X is completed // umount the erofs fs cachefiles_put_object() // object will be freed cachefiles_ondemand_deinit_obj_info() kmem_cache_free(object) // both info and object are freed ondemand_object_worker() When dropping an object, it is no longer necessary to reopen the object, so use cancel_work_sync() to cancel or wait for ondemand_object_worker() to finish.

In the Linux kernel, the following vulnerability has been resolved: PCI/MSI: Fix UAF in msi_capability_init KFENCE reports the following UAF: BUG: KFENCE: use-after-free read in __pci_enable_msi_range+0x2c0/0x488 Use-after-free read at 0x0000000024629571 (in kfence-#12): __pci_enable_msi_range+0x2c0/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 kfence-#12: 0x0000000008614900-0x00000000e06c228d, size=104, cache=kmalloc-128 allocated by task 81 on cpu 7 at 10.808142s: __kmem_cache_alloc_node+0x1f0/0x2bc kmalloc_trace+0x44/0x138 msi_alloc_desc+0x3c/0x9c msi_domain_insert_msi_desc+0x30/0x78 msi_setup_msi_desc+0x13c/0x184 __pci_enable_msi_range+0x258/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 freed by task 81 on cpu 7 at 10.811436s: msi_domain_free_descs+0xd4/0x10c msi_domain_free_locked.part.0+0xc0/0x1d8 msi_domain_alloc_irqs_all_locked+0xb4/0xbc pci_msi_setup_msi_irqs+0x30/0x4c __pci_enable_msi_range+0x2a8/0x488 pci_alloc_irq_vectors_affinity+0xec/0x14c pci_alloc_irq_vectors+0x18/0x28 Descriptor allocation done in: __pci_enable_msi_range msi_capability_init msi_setup_msi_desc msi_insert_msi_desc msi_domain_insert_msi_desc msi_alloc_desc ... Freed in case of failure in __msi_domain_alloc_locked() __pci_enable_msi_range msi_capability_init pci_msi_setup_msi_irqs msi_domain_alloc_irqs_all_locked msi_domain_alloc_locked __msi_domain_alloc_locked => fails msi_domain_free_locked ... That failure propagates back to pci_msi_setup_msi_irqs() in msi_capability_init() which accesses the descriptor for unmasking in the error exit path. Cure it by copying the descriptor and using the copy for the error exit path unmask operation. [ tglx: Massaged change log ]

In the Linux kernel, the following vulnerability has been resolved: cachefiles: defer exposing anon_fd until after copy_to_user() succeeds After installing the anonymous fd, we can now see it in userland and close it. However, at this point we may not have gotten the reference count of the cache, but we will put it during colse fd, so this may cause a cache UAF. So grab the cache reference count before fd_install(). In addition, by kernel convention, fd is taken over by the user land after fd_install(), and the kernel should not call close_fd() after that, i.e., it should call fd_install() after everything is ready, thus fd_install() is called after copy_to_user() succeeds.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: tcpm: fix use-after-free case in tcpm_register_source_caps There could be a potential use-after-free case in tcpm_register_source_caps(). This could happen when: * new (say invalid) source caps are advertised * the existing source caps are unregistered * tcpm_register_source_caps() returns with an error as usb_power_delivery_register_capabilities() fails This causes port->partner_source_caps to hold on to the now freed source caps. Reset port->partner_source_caps value to NULL after unregistering existing source caps.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: remove requests from xarray during flushing requests Even with CACHEFILES_DEAD set, we can still read the requests, so in the following concurrency the request may be used after it has been freed: mount | daemon_thread1 | daemon_thread2 ------------------------------------------------------------ cachefiles_ondemand_init_object cachefiles_ondemand_send_req REQ_A = kzalloc(sizeof(*req) + data_len) wait_for_completion(&REQ_A->done) cachefiles_daemon_read cachefiles_ondemand_daemon_read // close dev fd cachefiles_flush_reqs complete(&REQ_A->done) kfree(REQ_A) xa_lock(&cache->reqs); cachefiles_ondemand_select_req req->msg.opcode != CACHEFILES_OP_READ // req use-after-free !!! xa_unlock(&cache->reqs); xa_destroy(&cache->reqs) Hence remove requests from cache->reqs when flushing them to avoid accessing freed requests.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Always stop health timer during driver removal Currently, if teardown_hca fails to execute during driver removal, mlx5 does not stop the health timer. Afterwards, mlx5 continue with driver teardown. This may lead to a UAF bug, which results in page fault Oops[1], since the health timer invokes after resources were freed. Hence, stop the health monitor even if teardown_hca fails. [1] mlx5_core 0000:18:00.0: E-Switch: Unload vfs: mode(LEGACY), nvfs(0), necvfs(0), active vports(0) mlx5_core 0000:18:00.0: E-Switch: Disable: mode(LEGACY), nvfs(0), necvfs(0), active vports(0) mlx5_core 0000:18:00.0: E-Switch: Disable: mode(LEGACY), nvfs(0), necvfs(0), active vports(0) mlx5_core 0000:18:00.0: E-Switch: cleanup mlx5_core 0000:18:00.0: wait_func:1155:(pid 1967079): TEARDOWN_HCA(0x103) timeout. Will cause a leak of a command resource mlx5_core 0000:18:00.0: mlx5_function_close:1288:(pid 1967079): tear_down_hca failed, skip cleanup BUG: unable to handle page fault for address: ffffa26487064230 PGD 100c00067 P4D 100c00067 PUD 100e5a067 PMD 105ed7067 PTE 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 0 Comm: swapper/0 Tainted: G OE ------- --- 6.7.0-68.fc38.x86_64 #1 Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0013.121520200651 12/15/2020 RIP: 0010:ioread32be+0x34/0x60 RSP: 0018:ffffa26480003e58 EFLAGS: 00010292 RAX: ffffa26487064200 RBX: ffff9042d08161a0 RCX: ffff904c108222c0 RDX: 000000010bbf1b80 RSI: ffffffffc055ddb0 RDI: ffffa26487064230 RBP: ffff9042d08161a0 R08: 0000000000000022 R09: ffff904c108222e8 R10: 0000000000000004 R11: 0000000000000441 R12: ffffffffc055ddb0 R13: ffffa26487064200 R14: ffffa26480003f00 R15: ffff904c108222c0 FS: 0000000000000000(0000) GS:ffff904c10800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffa26487064230 CR3: 00000002c4420006 CR4: 00000000007706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <IRQ> ? __die+0x23/0x70 ? page_fault_oops+0x171/0x4e0 ? exc_page_fault+0x175/0x180 ? asm_exc_page_fault+0x26/0x30 ? __pfx_poll_health+0x10/0x10 [mlx5_core] ? __pfx_poll_health+0x10/0x10 [mlx5_core] ? ioread32be+0x34/0x60 mlx5_health_check_fatal_sensors+0x20/0x100 [mlx5_core] ? __pfx_poll_health+0x10/0x10 [mlx5_core] poll_health+0x42/0x230 [mlx5_core] ? __next_timer_interrupt+0xbc/0x110 ? __pfx_poll_health+0x10/0x10 [mlx5_core] call_timer_fn+0x21/0x130 ? __pfx_poll_health+0x10/0x10 [mlx5_core] __run_timers+0x222/0x2c0 run_timer_softirq+0x1d/0x40 __do_softirq+0xc9/0x2c8 __irq_exit_rcu+0xa6/0xc0 sysvec_apic_timer_interrupt+0x72/0x90 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x1a/0x20 RIP: 0010:cpuidle_enter_state+0xcc/0x440 ? cpuidle_enter_state+0xbd/0x440 cpuidle_enter+0x2d/0x40 do_idle+0x20d/0x270 cpu_startup_entry+0x2a/0x30 rest_init+0xd0/0xd0 arch_call_rest_init+0xe/0x30 start_kernel+0x709/0xa90 x86_64_start_reservations+0x18/0x30 x86_64_start_kernel+0x96/0xa0 secondary_startup_64_no_verify+0x18f/0x19b ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: cachefiles: Set object to close if ondemand_id < 0 in copen If copen is maliciously called in the user mode, it may delete the request corresponding to the random id. And the request may have not been read yet. Note that when the object is set to reopen, the open request will be done with the still reopen state in above case. As a result, the request corresponding to this object is always skipped in select_req function, so the read request is never completed and blocks other process. Fix this issue by simply set object to close if its id < 0 in copen.

In the Linux kernel, the following vulnerability has been resolved: ionic: fix use after netif_napi_del() When queues are started, netif_napi_add() and napi_enable() are called. If there are 4 queues and only 3 queues are used for the current configuration, only 3 queues' napi should be registered and enabled. The ionic_qcq_enable() checks whether the .poll pointer is not NULL for enabling only the using queue' napi. Unused queues' napi will not be registered by netif_napi_add(), so the .poll pointer indicates NULL. But it couldn't distinguish whether the napi was unregistered or not because netif_napi_del() doesn't reset the .poll pointer to NULL. So, ionic_qcq_enable() calls napi_enable() for the queue, which was unregistered by netif_napi_del(). Reproducer: ethtool -L <interface name> rx 1 tx 1 combined 0 ethtool -L <interface name> rx 0 tx 0 combined 1 ethtool -L <interface name> rx 0 tx 0 combined 4 Splat looks like: kernel BUG at net/core/dev.c:6666! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 PID: 1057 Comm: kworker/3:3 Not tainted 6.10.0-rc2+ #16 Workqueue: events ionic_lif_deferred_work [ionic] RIP: 0010:napi_enable+0x3b/0x40 Code: 48 89 c2 48 83 e2 f6 80 b9 61 09 00 00 00 74 0d 48 83 bf 60 01 00 00 00 74 03 80 ce 01 f0 4f RSP: 0018:ffffb6ed83227d48 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff97560cda0828 RCX: 0000000000000029 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff97560cda0a28 RBP: ffffb6ed83227d50 R08: 0000000000000400 R09: 0000000000000001 R10: 0000000000000001 R11: 0000000000000001 R12: 0000000000000000 R13: ffff97560ce3c1a0 R14: 0000000000000000 R15: ffff975613ba0a20 FS: 0000000000000000(0000) GS:ffff975d5f780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8f734ee200 CR3: 0000000103e50000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? die+0x33/0x90 ? do_trap+0xd9/0x100 ? napi_enable+0x3b/0x40 ? do_error_trap+0x83/0xb0 ? napi_enable+0x3b/0x40 ? napi_enable+0x3b/0x40 ? exc_invalid_op+0x4e/0x70 ? napi_enable+0x3b/0x40 ? asm_exc_invalid_op+0x16/0x20 ? napi_enable+0x3b/0x40 ionic_qcq_enable+0xb7/0x180 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_start_queues+0xc4/0x290 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_link_status_check+0x11c/0x170 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] ionic_lif_deferred_work+0x129/0x280 [ionic 59bdfc8a035436e1c4224ff7d10789e3f14643f8] process_one_work+0x145/0x360 worker_thread+0x2bb/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0xcc/0x100 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: 9p: add missing locking around taking dentry fid list Fix a use-after-free on dentry's d_fsdata fid list when a thread looks up a fid through dentry while another thread unlinks it: UAF thread: refcount_t: addition on 0; use-after-free. p9_fid_get linux/./include/net/9p/client.h:262 v9fs_fid_find+0x236/0x280 linux/fs/9p/fid.c:129 v9fs_fid_lookup_with_uid linux/fs/9p/fid.c:181 v9fs_fid_lookup+0xbf/0xc20 linux/fs/9p/fid.c:314 v9fs_vfs_getattr_dotl+0xf9/0x360 linux/fs/9p/vfs_inode_dotl.c:400 vfs_statx+0xdd/0x4d0 linux/fs/stat.c:248 Freed by: p9_fid_destroy (inlined) p9_client_clunk+0xb0/0xe0 linux/net/9p/client.c:1456 p9_fid_put linux/./include/net/9p/client.h:278 v9fs_dentry_release+0xb5/0x140 linux/fs/9p/vfs_dentry.c:55 v9fs_remove+0x38f/0x620 linux/fs/9p/vfs_inode.c:518 vfs_unlink+0x29a/0x810 linux/fs/namei.c:4335 The problem is that d_fsdata was not accessed under d_lock, because d_release() normally is only called once the dentry is otherwise no longer accessible but since we also call it explicitly in v9fs_remove that lock is required: move the hlist out of the dentry under lock then unref its fids once they are no longer accessible.

In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: fix use-after-free due to race with dev replace While loading a zone's info during creation of a block group, we can race with a device replace operation and then trigger a use-after-free on the device that was just replaced (source device of the replace operation). This happens because at btrfs_load_zone_info() we extract a device from the chunk map into a local variable and then use the device while not under the protection of the device replace rwsem. So if there's a device replace operation happening when we extract the device and that device is the source of the replace operation, we will trigger a use-after-free if before we finish using the device the replace operation finishes and frees the device. Fix this by enlarging the critical section under the protection of the device replace rwsem so that all uses of the device are done inside the critical section.

A use-after-free flaw was found in the Linux kernel's netfilter in the way a user triggers the nft_pipapo_remove function with the element, without a NFT_SET_EXT_KEY_END. This issue could allow a local user to crash the system or potentially escalate their privileges on the system.

A flaw was found in the Linux kernel’s implementation of MIDI, where an attacker with a local account and the permissions to issue ioctl commands to midi devices could trigger a use-after-free issue. A write to this specific memory while freed and before use causes the flow of execution to change and possibly allow for memory corruption or privilege escalation. The highest threat from this vulnerability is to confidentiality, integrity, as well as system availability.

In the Linux kernel, the following vulnerability has been resolved: ima: Fix use-after-free on a dentry's dname.name ->d_name.name can change on rename and the earlier value can be freed; there are conditions sufficient to stabilize it (->d_lock on dentry, ->d_lock on its parent, ->i_rwsem exclusive on the parent's inode, rename_lock), but none of those are met at any of the sites. Take a stable snapshot of the name instead.

A vulnerability was found in the Linux Kernel where the function sunkbd_reinit having been scheduled by sunkbd_interrupt before sunkbd being freed. Though the dangling pointer is set to NULL in sunkbd_disconnect, there is still an alias in sunkbd_reinit causing Use After Free.

A vulnerability was found in Linux Kernel where refcount leak in llcp_sock_bind() causing use-after-free which might lead to privilege escalations.

The dccp_disconnect function in net/dccp/proto.c in the Linux kernel through 4.14.3 allows local users to gain privileges or cause a denial of service (use-after-free) via an AF_UNSPEC connect system call during the DCCP_LISTEN state.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. On an error when building a nftables rule, deactivating immediate expressions in nft_immediate_deactivate() can lead unbinding the chain and objects be deactivated but later used. We recommend upgrading past commit 0a771f7b266b02d262900c75f1e175c7fe76fec2.

In the Linux kernel, the following vulnerability has been resolved: cachefiles: fix slab-use-after-free in cachefiles_ondemand_daemon_read() We got the following issue in a fuzz test of randomly issuing the restore command: ================================================================== BUG: KASAN: slab-use-after-free in cachefiles_ondemand_daemon_read+0xb41/0xb60 Read of size 8 at addr ffff888122e84088 by task ondemand-04-dae/963 CPU: 13 PID: 963 Comm: ondemand-04-dae Not tainted 6.8.0-dirty #564 Call Trace: kasan_report+0x93/0xc0 cachefiles_ondemand_daemon_read+0xb41/0xb60 vfs_read+0x169/0xb50 ksys_read+0xf5/0x1e0 Allocated by task 116: kmem_cache_alloc+0x140/0x3a0 cachefiles_lookup_cookie+0x140/0xcd0 fscache_cookie_state_machine+0x43c/0x1230 [...] Freed by task 792: kmem_cache_free+0xfe/0x390 cachefiles_put_object+0x241/0x480 fscache_cookie_state_machine+0x5c8/0x1230 [...] ================================================================== Following is the process that triggers the issue: mount | daemon_thread1 | daemon_thread2 ------------------------------------------------------------ cachefiles_withdraw_cookie cachefiles_ondemand_clean_object(object) cachefiles_ondemand_send_req REQ_A = kzalloc(sizeof(*req) + data_len) wait_for_completion(&REQ_A->done) cachefiles_daemon_read cachefiles_ondemand_daemon_read REQ_A = cachefiles_ondemand_select_req msg->object_id = req->object->ondemand->ondemand_id ------ restore ------ cachefiles_ondemand_restore xas_for_each(&xas, req, ULONG_MAX) xas_set_mark(&xas, CACHEFILES_REQ_NEW) cachefiles_daemon_read cachefiles_ondemand_daemon_read REQ_A = cachefiles_ondemand_select_req copy_to_user(_buffer, msg, n) xa_erase(&cache->reqs, id) complete(&REQ_A->done) ------ close(fd) ------ cachefiles_ondemand_fd_release cachefiles_put_object cachefiles_put_object kmem_cache_free(cachefiles_object_jar, object) REQ_A->object->ondemand->ondemand_id // object UAF !!! When we see the request within xa_lock, req->object must not have been freed yet, so grab the reference count of object before xa_unlock to avoid the above issue.

A use-after-free vulnerability in the Linux kernel's netfilter: nf_tables component can be exploited to achieve local privilege escalation. The nft_setelem_catchall_deactivate() function checks whether the catch-all set element is active in the current generation instead of the next generation before freeing it, but only flags it inactive in the next generation, making it possible to free the element multiple times, leading to a double free vulnerability. We recommend upgrading past commit b1db244ffd041a49ecc9618e8feb6b5c1afcdaa7.

An issue was discovered in l2cap_sock_release in net/bluetooth/l2cap_sock.c in the Linux kernel before 6.4.10. There is a use-after-free because the children of an sk are mishandled.