In the Linux kernel, the following vulnerability has been resolved: serial: 8250: Fix PM usage_count for console handover When console is enabled, univ8250_console_setup() calls serial8250_console_setup() before .dev is set to uart_port. Therefore, it will not call pm_runtime_get_sync(). Later, when the actual driver is going to take over univ8250_console_exit() is called. As .dev is already set, serial8250_console_exit() makes pm_runtime_put_sync() call with usage count being zero triggering PM usage count warning (extra debug for univ8250_console_setup(), univ8250_console_exit(), and serial8250_register_ports()): [ 0.068987] univ8250_console_setup ttyS0 nodev [ 0.499670] printk: console [ttyS0] enabled [ 0.717955] printk: console [ttyS0] printing thread started [ 1.960163] serial8250_register_ports assigned dev for ttyS0 [ 1.976830] printk: console [ttyS0] disabled [ 1.976888] printk: console [ttyS0] printing thread stopped [ 1.977073] univ8250_console_exit ttyS0 usage:0 [ 1.977075] serial8250 serial8250: Runtime PM usage count underflow! [ 1.977429] dw-apb-uart.6: ttyS0 at MMIO 0x4010006000 (irq = 33, base_baud = 115200) is a 16550A [ 1.977812] univ8250_console_setup ttyS0 usage:2 [ 1.978167] printk: console [ttyS0] printing thread started [ 1.978203] printk: console [ttyS0] enabled To fix the issue, call pm_runtime_get_sync() in serial8250_register_ports() as soon as .dev is set for an uart_port if it has console enabled. This problem became apparent only recently because 82586a721595 ("PM: runtime: Avoid device usage count underflows") added the warning printout. I confirmed this problem also occurs with v5.18 (w/o the warning printout, obviously).

In the Linux kernel, the following vulnerability has been resolved: media: aspeed: fix clock handling logic Video engine uses eclk and vclk for its clock sources and its reset control is coupled with eclk so the current clock enabling sequence works like below. Enable eclk De-assert Video Engine reset 10ms delay Enable vclk It introduces improper reset on the Video Engine hardware and eventually the hardware generates unexpected DMA memory transfers that can corrupt memory region in random and sporadic patterns. This issue is observed very rarely on some specific AST2500 SoCs but it causes a critical kernel panic with making a various shape of signature so it's extremely hard to debug. Moreover, the issue is observed even when the video engine is not actively used because udevd turns on the video engine hardware for a short time to make a query in every boot. To fix this issue, this commit changes the clock handling logic to make the reset de-assertion triggered after enabling both eclk and vclk. Also, it adds clk_unprepare call for a case when probe fails. clk: ast2600: fix reset settings for eclk and vclk Video engine reset setting should be coupled with eclk to match it with the setting for previous Aspeed SoCs which is defined in clk-aspeed.c since all Aspeed SoCs are sharing a single video engine driver. Also, reset bit 6 is defined as 'Video Engine' reset in datasheet so it should be de-asserted when eclk is enabled. This commit fixes the setting.

In the Linux kernel, the following vulnerability has been resolved: mm: vmalloc: ensure vmap_block is initialised before adding to queue Commit 8c61291fd850 ("mm: fix incorrect vbq reference in purge_fragmented_block") extended the 'vmap_block' structure to contain a 'cpu' field which is set at allocation time to the id of the initialising CPU. When a new 'vmap_block' is being instantiated by new_vmap_block(), the partially initialised structure is added to the local 'vmap_block_queue' xarray before the 'cpu' field has been initialised. If another CPU is concurrently walking the xarray (e.g. via vm_unmap_aliases()), then it may perform an out-of-bounds access to the remote queue thanks to an uninitialised index. This has been observed as UBSAN errors in Android: | Internal error: UBSAN: array index out of bounds: 00000000f2005512 [#1] PREEMPT SMP | | Call trace: | purge_fragmented_block+0x204/0x21c | _vm_unmap_aliases+0x170/0x378 | vm_unmap_aliases+0x1c/0x28 | change_memory_common+0x1dc/0x26c | set_memory_ro+0x18/0x24 | module_enable_ro+0x98/0x238 | do_init_module+0x1b0/0x310 Move the initialisation of 'vb->cpu' in new_vmap_block() ahead of the addition to the xarray.

In the Linux kernel, the following vulnerability has been resolved: staging: r8188eu: prevent ->Ssid overflow in rtw_wx_set_scan() This code has a check to prevent read overflow but it needs another check to prevent writing beyond the end of the ->Ssid[] array.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: avoid using null object of framebuffer Instead of using state->fb->obj[0] directly, get object from framebuffer by calling drm_gem_fb_get_obj() and return error code when object is null to avoid using null object of framebuffer. (cherry picked from commit 73dd0ad9e5dad53766ea3e631303430116f834b3)

In the Linux kernel, the following vulnerability has been resolved: xtensa: Fix refcount leak bug in time.c In calibrate_ccount(), of_find_compatible_node() will return a node pointer with refcount incremented. We should use of_node_put() when it is not used anymore.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix combination of jit blinding and pointers to bpf subprogs. The combination of jit blinding and pointers to bpf subprogs causes: [ 36.989548] BUG: unable to handle page fault for address: 0000000100000001 [ 36.990342] #PF: supervisor instruction fetch in kernel mode [ 36.990968] #PF: error_code(0x0010) - not-present page [ 36.994859] RIP: 0010:0x100000001 [ 36.995209] Code: Unable to access opcode bytes at RIP 0xffffffd7. [ 37.004091] Call Trace: [ 37.004351] <TASK> [ 37.004576] ? bpf_loop+0x4d/0x70 [ 37.004932] ? bpf_prog_3899083f75e4c5de_F+0xe3/0x13b The jit blinding logic didn't recognize that ld_imm64 with an address of bpf subprogram is a special instruction and proceeded to randomize it. By itself it wouldn't have been an issue, but jit_subprogs() logic relies on two step process to JIT all subprogs and then JIT them again when addresses of all subprogs are known. Blinding process in the first JIT phase caused second JIT to miss adjustment of special ld_imm64. Fix this issue by ignoring special ld_imm64 instructions that don't have user controlled constants and shouldn't be blinded.

In the Linux kernel, the following vulnerability has been resolved: can: j1939: implement NETDEV_UNREGISTER notification handler syzbot is reporting unregister_netdevice: waiting for vcan0 to become free. Usage count = 2 problem, for j1939 protocol did not have NETDEV_UNREGISTER notification handler for undoing changes made by j1939_sk_bind(). Commit 25fe97cb7620 ("can: j1939: move j1939_priv_put() into sk_destruct callback") expects that a call to j1939_priv_put() can be unconditionally delayed until j1939_sk_sock_destruct() is called. But we need to call j1939_priv_put() against an extra ref held by j1939_sk_bind() call (as a part of undoing changes made by j1939_sk_bind()) as soon as NETDEV_UNREGISTER notification fires (i.e. before j1939_sk_sock_destruct() is called via j1939_sk_release()). Otherwise, the extra ref on "struct j1939_priv" held by j1939_sk_bind() call prevents "struct net_device" from dropping the usage count to 1; making it impossible for unregister_netdevice() to continue. [mkl: remove space in front of label]

In the Linux kernel, the following vulnerability has been resolved: can: mcp251x: fix deadlock if an interrupt occurs during mcp251x_open The mcp251x_hw_wake() function is called with the mpc_lock mutex held and disables the interrupt handler so that no interrupts can be processed while waking the device. If an interrupt has already occurred then waiting for the interrupt handler to complete will deadlock because it will be trying to acquire the same mutex. CPU0 CPU1 ---- ---- mcp251x_open() mutex_lock(&priv->mcp_lock) request_threaded_irq() <interrupt> mcp251x_can_ist() mutex_lock(&priv->mcp_lock) mcp251x_hw_wake() disable_irq() <-- deadlock Use disable_irq_nosync() instead because the interrupt handler does everything while holding the mutex so it doesn't matter if it's still running.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: the warning dereferencing obj for nbio_v7_4 if ras_manager obj null, don't print NBIO err data

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Check index for aux_rd_interval before using aux_rd_interval has size of 7 and should be checked. This fixes 3 OVERRUN and 1 INTEGER_OVERFLOW issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: soc: qcom: cmd-db: Map shared memory as WC, not WB Linux does not write into cmd-db region. This region of memory is write protected by XPU. XPU may sometime falsely detect clean cache eviction as "write" into the write protected region leading to secure interrupt which causes an endless loop somewhere in Trust Zone. The only reason it is working right now is because Qualcomm Hypervisor maps the same region as Non-Cacheable memory in Stage 2 translation tables. The issue manifests if we want to use another hypervisor (like Xen or KVM), which does not know anything about those specific mappings. Changing the mapping of cmd-db memory from MEMREMAP_WB to MEMREMAP_WT/WC removes dependency on correct mappings in Stage 2 tables. This patch fixes the issue by updating the mapping to MEMREMAP_WC. I tested this on SA8155P with Xen.

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: ti: am65-cpsw: Fix NULL dereference on XDP_TX If number of TX queues are set to 1 we get a NULL pointer dereference during XDP_TX. ~# ethtool -L eth0 tx 1 ~# ./xdp-trafficgen udp -A <ipv6-src> -a <ipv6-dst> eth0 -t 2 Transmitting on eth0 (ifindex 2) [ 241.135257] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000030 Fix this by using actual TX queues instead of max TX queues when picking the TX channel in am65_cpsw_ndo_xdp_xmit().

In the Linux kernel, the following vulnerability has been resolved: s390/sclp: Fix SCCB present check Tracing code called by the SCLP interrupt handler contains early exits if the SCCB address associated with an interrupt is NULL. This check is performed after physical to virtual address translation. If the kernel identity mapping does not start at address zero, the resulting virtual address is never zero, so that the NULL checks won't work. Subsequently this may result in incorrect accesses to the first page of the identity mapping. Fix this by introducing a function that handles the NULL case before address translation.

In the Linux kernel, the following vulnerability has been resolved: nfsd: prevent panic for nfsv4.0 closed files in nfs4_show_open Prior to commit 3f29cc82a84c ("nfsd: split sc_status out of sc_type") states_show() relied on sc_type field to be of valid type before calling into a subfunction to show content of a particular stateid. From that commit, we split the validity of the stateid into sc_status and no longer changed sc_type to 0 while unhashing the stateid. This resulted in kernel oopsing for nfsv4.0 opens that stay around and in nfs4_show_open() would derefence sc_file which was NULL. Instead, for closed open stateids forgo displaying information that relies of having a valid sc_file. To reproduce: mount the server with 4.0, read and close a file and then on the server cat /proc/fs/nfsd/clients/2/states [ 513.590804] Call trace: [ 513.590925] _raw_spin_lock+0xcc/0x160 [ 513.591119] nfs4_show_open+0x78/0x2c0 [nfsd] [ 513.591412] states_show+0x44c/0x488 [nfsd] [ 513.591681] seq_read_iter+0x5d8/0x760 [ 513.591896] seq_read+0x188/0x208 [ 513.592075] vfs_read+0x148/0x470 [ 513.592241] ksys_read+0xcc/0x178

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: possible module reference underflow in error path dst->ops is set on when nft_expr_clone() fails, but module refcount has not been bumped yet, therefore nft_expr_destroy() leads to module reference underflow.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: double hook unregistration in netns path __nft_release_hooks() is called from pre_netns exit path which unregisters the hooks, then the NETDEV_UNREGISTER event is triggered which unregisters the hooks again. [ 565.221461] WARNING: CPU: 18 PID: 193 at net/netfilter/core.c:495 __nf_unregister_net_hook+0x247/0x270 [...] [ 565.246890] CPU: 18 PID: 193 Comm: kworker/u64:1 Tainted: G E 5.18.0-rc7+ #27 [ 565.253682] Workqueue: netns cleanup_net [ 565.257059] RIP: 0010:__nf_unregister_net_hook+0x247/0x270 [...] [ 565.297120] Call Trace: [ 565.300900] <TASK> [ 565.304683] nf_tables_flowtable_event+0x16a/0x220 [nf_tables] [ 565.308518] raw_notifier_call_chain+0x63/0x80 [ 565.312386] unregister_netdevice_many+0x54f/0xb50 Unregister and destroy netdev hook from netns pre_exit via kfree_rcu so the NETDEV_UNREGISTER path see unregistered hooks.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix memory leaks in __check_func_call kmemleak reports this issue: unreferenced object 0xffff88817139d000 (size 2048): comm "test_progs", pid 33246, jiffies 4307381979 (age 45851.820s) hex dump (first 32 bytes): 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<0000000045f075f0>] kmalloc_trace+0x27/0xa0 [<0000000098b7c90a>] __check_func_call+0x316/0x1230 [<00000000b4c3c403>] check_helper_call+0x172e/0x4700 [<00000000aa3875b7>] do_check+0x21d8/0x45e0 [<000000001147357b>] do_check_common+0x767/0xaf0 [<00000000b5a595b4>] bpf_check+0x43e3/0x5bc0 [<0000000011e391b1>] bpf_prog_load+0xf26/0x1940 [<0000000007f765c0>] __sys_bpf+0xd2c/0x3650 [<00000000839815d6>] __x64_sys_bpf+0x75/0xc0 [<00000000946ee250>] do_syscall_64+0x3b/0x90 [<0000000000506b7f>] entry_SYSCALL_64_after_hwframe+0x63/0xcd The root case here is: In function prepare_func_exit(), the callee is not released in the abnormal scenario after "state->curframe--;". To fix, move "state->curframe--;" to the very bottom of the function, right when we free callee and reset frame[] pointer to NULL, as Andrii suggested. In addition, function __check_func_call() has a similar problem. In the abnormal scenario before "state->curframe++;", the callee also should be released by free_func_state().

In the Linux kernel, the following vulnerability has been resolved: ARM: OMAP2+: Fix refcount leak in omapdss_init_of omapdss_find_dss_of_node() calls of_find_compatible_node() to get device node. of_find_compatible_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() in later error path and normal path.

In the Linux kernel, the following vulnerability has been resolved: spi: spi-qpic-snand: unregister ECC engine on probe error and device remove The on-host hardware ECC engine remains registered both when the spi_register_controller() function returns with an error and also on device removal. Change the qcom_spi_probe() function to unregister the engine on the error path, and add the missing unregistering call to qcom_spi_remove() to avoid possible use-after-free issues.

In the Linux kernel, the following vulnerability has been resolved: usb: aspeed-vhub: Fix refcount leak bug in ast_vhub_init_desc() We should call of_node_put() for the reference returned by of_get_child_by_name() which has increased the refcount.

In the Linux kernel, the following vulnerability has been resolved: media: venus: protect against spurious interrupts during probe Make sure the interrupt handler is initialized before the interrupt is registered. If the IRQ is registered before hfi_create(), it's possible that an interrupt fires before the handler setup is complete, leading to a NULL dereference. This error condition has been observed during system boot on Rb3Gen2.

In the Linux kernel, the following vulnerability has been resolved: dm raid: fix KASAN warning in raid5_add_disks There's a KASAN warning in raid5_add_disk when running the LVM testsuite. The warning happens in the test lvconvert-raid-reshape-linear_to_raid6-single-type.sh. We fix the warning by verifying that rdev->saved_raid_disk is within limits.

In the Linux kernel, the following vulnerability has been resolved: ublk_drv: fix NULL pointer dereference in ublk_ctrl_start_recovery() When two UBLK_CMD_START_USER_RECOVERY commands are submitted, the first one sets 'ubq->ubq_daemon' to NULL, and the second one triggers WARN in ublk_queue_reinit() and subsequently a NULL pointer dereference issue. Fix it by adding the check in ublk_ctrl_start_recovery() and return immediately in case of zero 'ub->nr_queues_ready'. BUG: kernel NULL pointer dereference, address: 0000000000000028 RIP: 0010:ublk_ctrl_start_recovery.constprop.0+0x82/0x180 Call Trace: <TASK> ? __die+0x20/0x70 ? page_fault_oops+0x75/0x170 ? exc_page_fault+0x64/0x140 ? asm_exc_page_fault+0x22/0x30 ? ublk_ctrl_start_recovery.constprop.0+0x82/0x180 ublk_ctrl_uring_cmd+0x4f7/0x6c0 ? pick_next_task_idle+0x26/0x40 io_uring_cmd+0x9a/0x1b0 io_issue_sqe+0x193/0x3f0 io_wq_submit_work+0x9b/0x390 io_worker_handle_work+0x165/0x360 io_wq_worker+0xcb/0x2f0 ? finish_task_switch.isra.0+0x203/0x290 ? finish_task_switch.isra.0+0x203/0x290 ? __pfx_io_wq_worker+0x10/0x10 ret_from_fork+0x2d/0x50 ? __pfx_io_wq_worker+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: trace/fgraph: Fix the warning caused by missing unregister notifier This warning was triggered during testing on v6.16: notifier callback ftrace_suspend_notifier_call already registered WARNING: CPU: 2 PID: 86 at kernel/notifier.c:23 notifier_chain_register+0x44/0xb0 ... Call Trace: <TASK> blocking_notifier_chain_register+0x34/0x60 register_ftrace_graph+0x330/0x410 ftrace_profile_write+0x1e9/0x340 vfs_write+0xf8/0x420 ? filp_flush+0x8a/0xa0 ? filp_close+0x1f/0x30 ? do_dup2+0xaf/0x160 ksys_write+0x65/0xe0 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x77/0x7f When writing to the function_profile_enabled interface, the notifier was not unregistered after start_graph_tracing failed, causing a warning the next time function_profile_enabled was written. Fixed by adding unregister_pm_notifier in the exception path.

In the Linux kernel, the following vulnerability has been resolved: driver: iio: add missing checks on iio_info's callback access Some callbacks from iio_info structure are accessed without any check, so if a driver doesn't implement them trying to access the corresponding sysfs entries produce a kernel oops such as: [ 2203.527791] Unable to handle kernel NULL pointer dereference at virtual address 00000000 when execute [...] [ 2203.783416] Call trace: [ 2203.783429] iio_read_channel_info_avail from dev_attr_show+0x18/0x48 [ 2203.789807] dev_attr_show from sysfs_kf_seq_show+0x90/0x120 [ 2203.794181] sysfs_kf_seq_show from seq_read_iter+0xd0/0x4e4 [ 2203.798555] seq_read_iter from vfs_read+0x238/0x2a0 [ 2203.802236] vfs_read from ksys_read+0xa4/0xd4 [ 2203.805385] ksys_read from ret_fast_syscall+0x0/0x54 [ 2203.809135] Exception stack(0xe0badfa8 to 0xe0badff0) [ 2203.812880] dfa0: 00000003 b6f10f80 00000003 b6eab000 00020000 00000000 [ 2203.819746] dfc0: 00000003 b6f10f80 7ff00000 00000003 00000003 00000000 00020000 00000000 [ 2203.826619] dfe0: b6e1bc88 bed80958 b6e1bc94 b6e1bcb0 [ 2203.830363] Code: bad PC value [ 2203.832695] ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: crypto: af_alg - Set merge to zero early in af_alg_sendmsg If an error causes af_alg_sendmsg to abort, ctx->merge may contain a garbage value from the previous loop. This may then trigger a crash on the next entry into af_alg_sendmsg when it attempts to do a merge that can't be done. Fix this by setting ctx->merge to zero near the start of the loop.

In the Linux kernel, the following vulnerability has been resolved: arm64: acpi: Harden get_cpu_for_acpi_id() against missing CPU entry In a review discussion of the changes to support vCPU hotplug where a check was added on the GICC being enabled if was online, it was noted that there is need to map back to the cpu and use that to index into a cpumask. As such, a valid ID is needed. If an MPIDR check fails in acpi_map_gic_cpu_interface() it is possible for the entry in cpu_madt_gicc[cpu] == NULL. This function would then cause a NULL pointer dereference. Whilst a path to trigger this has not been established, harden this caller against the possibility.

In the Linux kernel, the following vulnerability has been resolved: Input: uinput - reject requests with unreasonable number of slots When exercising uinput interface syzkaller may try setting up device with a really large number of slots, which causes memory allocation failure in input_mt_init_slots(). While this allocation failure is handled properly and request is rejected, it results in syzkaller reports. Additionally, such request may put undue burden on the system which will try to free a lot of memory for a bogus request. Fix it by limiting allowed number of slots to 100. This can easily be extended if we see devices that can track more than 100 contacts.

In the Linux kernel, the following vulnerability has been resolved: smb/server: fix potential null-ptr-deref of lease_ctx_info in smb2_open() null-ptr-deref will occur when (req_op_level == SMB2_OPLOCK_LEVEL_LEASE) and parse_lease_state() return NULL. Fix this by check if 'lease_ctx_info' is NULL. Additionally, remove the redundant parentheses in parse_durable_handle_context().

In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel: Limit the period on Haswell Running the ltp test cve-2015-3290 concurrently reports the following warnings. perfevents: irq loop stuck! WARNING: CPU: 31 PID: 32438 at arch/x86/events/intel/core.c:3174 intel_pmu_handle_irq+0x285/0x370 Call Trace: <NMI> ? __warn+0xa4/0x220 ? intel_pmu_handle_irq+0x285/0x370 ? __report_bug+0x123/0x130 ? intel_pmu_handle_irq+0x285/0x370 ? __report_bug+0x123/0x130 ? intel_pmu_handle_irq+0x285/0x370 ? report_bug+0x3e/0xa0 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x18/0x50 ? asm_exc_invalid_op+0x1a/0x20 ? irq_work_claim+0x1e/0x40 ? intel_pmu_handle_irq+0x285/0x370 perf_event_nmi_handler+0x3d/0x60 nmi_handle+0x104/0x330 Thanks to Thomas Gleixner's analysis, the issue is caused by the low initial period (1) of the frequency estimation algorithm, which triggers the defects of the HW, specifically erratum HSW11 and HSW143. (For the details, please refer https://lore.kernel.org/lkml/87plq9l5d2.ffs@tglx/) The HSW11 requires a period larger than 100 for the INST_RETIRED.ALL event, but the initial period in the freq mode is 1. The erratum is the same as the BDM11, which has been supported in the kernel. A minimum period of 128 is enforced as well on HSW. HSW143 is regarding that the fixed counter 1 may overcount 32 with the Hyper-Threading is enabled. However, based on the test, the hardware has more issues than it tells. Besides the fixed counter 1, the message 'interrupt took too long' can be observed on any counter which was armed with a period < 32 and two events expired in the same NMI. A minimum period of 32 is enforced for the rest of the events. The recommended workaround code of the HSW143 is not implemented. Because it only addresses the issue for the fixed counter. It brings extra overhead through extra MSR writing. No related overcounting issue has been reported so far.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Remove SCSI host only if added If host tries to remove ufshcd driver from a UFS device it would cause a kernel panic if ufshcd_async_scan fails during ufshcd_probe_hba before adding a SCSI host with scsi_add_host and MCQ is enabled since SCSI host has been defered after MCQ configuration introduced by commit 0cab4023ec7b ("scsi: ufs: core: Defer adding host to SCSI if MCQ is supported"). To guarantee that SCSI host is removed only if it has been added, set the scsi_host_added flag to true after adding a SCSI host and check whether it is set or not before removing it.

In the Linux kernel, the following vulnerability has been resolved: ASoC: Intel: Boards: Fix NULL pointer deref in BYT/CHT boards harder Since commit 13f58267cda3 ("ASoC: soc.h: don't create dummy Component via COMP_DUMMY()") dummy codecs declared like this: SND_SOC_DAILINK_DEF(dummy, DAILINK_COMP_ARRAY(COMP_DUMMY())); expand to: static struct snd_soc_dai_link_component dummy[] = { }; Which means that dummy is a zero sized array and thus dais[i].codecs should not be dereferenced *at all* since it points to the address of the next variable stored in the data section as the "dummy" variable has an address but no size, so even dereferencing dais[0] is already an out of bounds array reference. Which means that the if (dais[i].codecs->name) check added in commit 7d99a70b6595 ("ASoC: Intel: Boards: Fix NULL pointer deref in BYT/CHT boards") relies on that the part of the next variable which the name member maps to just happens to be NULL. Which apparently so far it usually is, except when it isn't and then it results in crashes like this one: [ 28.795659] BUG: unable to handle page fault for address: 0000000000030011 ... [ 28.795780] Call Trace: [ 28.795787] <TASK> ... [ 28.795862] ? strcmp+0x18/0x40 [ 28.795872] 0xffffffffc150c605 [ 28.795887] platform_probe+0x40/0xa0 ... [ 28.795979] ? __pfx_init_module+0x10/0x10 [snd_soc_sst_bytcr_wm5102] Really fix things this time around by checking dais.num_codecs != 0.

In the Linux kernel, the following vulnerability has been resolved: nfc: pn533: Add poll mod list filling check In case of im_protocols value is 1 and tm_protocols value is 0 this combination successfully passes the check 'if (!im_protocols && !tm_protocols)' in the nfc_start_poll(). But then after pn533_poll_create_mod_list() call in pn533_start_poll() poll mod list will remain empty and dev->poll_mod_count will remain 0 which lead to division by zero. Normally no im protocol has value 1 in the mask, so this combination is not expected by driver. But these protocol values actually come from userspace via Netlink interface (NFC_CMD_START_POLL operation). So a broken or malicious program may pass a message containing a "bad" combination of protocol parameter values so that dev->poll_mod_count is not incremented inside pn533_poll_create_mod_list(), thus leading to division by zero. Call trace looks like: nfc_genl_start_poll() nfc_start_poll() ->start_poll() pn533_start_poll() Add poll mod list filling check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: tty: Fix a possible resource leak in icom_probe When pci_read_config_dword failed, call pci_release_regions() and pci_disable_device() to recycle the resource previously allocated.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: ucsi: Fix null pointer dereference in trace ucsi_register_altmode checks IS_ERR for the alt pointer and treats NULL as valid. When CONFIG_TYPEC_DP_ALTMODE is not enabled, ucsi_register_displayport returns NULL which causes a NULL pointer dereference in trace. Rather than return NULL, call typec_port_register_altmode to register DisplayPort alternate mode as a non-controllable mode when CONFIG_TYPEC_DP_ALTMODE is not enabled.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Fix the warning division or modulo by zero Checks the partition mode and returns an error for an invalid mode.

In the Linux kernel, the following vulnerability has been resolved: Revert "serial: 8250_omap: Set the console genpd always on if no console suspend" This reverts commit 68e6939ea9ec3d6579eadeab16060339cdeaf940. Kevin reported that this causes a crash during suspend on platforms that dont use PM domains.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/client: add missing bo locking in show_meminfo() bo_meminfo() wants to inspect bo state like tt and the ttm resource, however this state can change at any point leading to stuff like NPD and UAF, if the bo lock is not held. Grab the bo lock when calling bo_meminfo(), ensuring we drop any spinlocks first. In the case of object_idr we now also need to hold a ref. v2 (MattB) - Also add xe_bo_assert_held() (cherry picked from commit 4f63d712fa104c3ebefcb289d1e733e86d8698c7)

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix memory leak on the deferred close xfstests on smb21 report kmemleak as below: unreferenced object 0xffff8881767d6200 (size 64): comm "xfs_io", pid 1284, jiffies 4294777434 (age 20.789s) hex dump (first 32 bytes): 80 5a d0 11 81 88 ff ff 78 8a aa 63 81 88 ff ff .Z......x..c.... 00 71 99 76 81 88 ff ff 00 00 00 00 00 00 00 00 .q.v............ backtrace: [<00000000ad04e6ea>] cifs_close+0x92/0x2c0 [<0000000028b93c82>] __fput+0xff/0x3f0 [<00000000d8116851>] task_work_run+0x85/0xc0 [<0000000027e14f9e>] do_exit+0x5e5/0x1240 [<00000000fb492b95>] do_group_exit+0x58/0xe0 [<00000000129a32d9>] __x64_sys_exit_group+0x28/0x30 [<00000000e3f7d8e9>] do_syscall_64+0x35/0x80 [<00000000102e8a0b>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 When cancel the deferred close work, we should also cleanup the struct cifs_deferred_close.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: Don't finalize CSA in IBSS mode if state is disconnected When we are not connected to a channel, sending channel "switch" announcement doesn't make any sense. The BSS list is empty in that case. This causes the for loop in cfg80211_get_bss() to be bypassed, so the function returns NULL (check line 1424 of net/wireless/scan.c), causing the WARN_ON() in ieee80211_ibss_csa_beacon() to get triggered (check line 500 of net/mac80211/ibss.c), which was consequently reported on the syzkaller dashboard. Thus, check if we have an existing connection before generating the CSA beacon in ieee80211_ibss_finish_csa().

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: E-Switch, pair only capable devices OFFLOADS paring using devcom is possible only on devices that support LAG. Filter based on lag capabilities. This fixes an issue where mlx5_get_next_phys_dev() was called without holding the interface lock. This issue was found when commit bc4c2f2e0179 ("net/mlx5: Lag, filter non compatible devices") added an assert that verifies the interface lock is held. WARNING: CPU: 9 PID: 1706 at drivers/net/ethernet/mellanox/mlx5/core/dev.c:642 mlx5_get_next_phys_dev+0xd2/0x100 [mlx5_core] Modules linked in: mlx5_vdpa vringh vhost_iotlb vdpa mlx5_ib mlx5_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_umad ib_ipoib ib_cm ib_uverbs ib_core overlay fuse [last unloaded: mlx5_core] CPU: 9 PID: 1706 Comm: devlink Not tainted 5.18.0-rc7+ #11 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5_get_next_phys_dev+0xd2/0x100 [mlx5_core] Code: 02 00 75 48 48 8b 85 80 04 00 00 5d c3 31 c0 5d c3 be ff ff ff ff 48 c7 c7 08 41 5b a0 e8 36 87 28 e3 85 c0 0f 85 6f ff ff ff <0f> 0b e9 68 ff ff ff 48 c7 c7 0c 91 cc 84 e8 cb 36 6f e1 e9 4d ff RSP: 0018:ffff88811bf47458 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff88811b398000 RCX: 0000000000000001 RDX: 0000000080000000 RSI: ffffffffa05b4108 RDI: ffff88812daaaa78 RBP: ffff88812d050380 R08: 0000000000000001 R09: ffff88811d6b3437 R10: 0000000000000001 R11: 00000000fddd3581 R12: ffff88815238c000 R13: ffff88812d050380 R14: ffff8881018aa7e0 R15: ffff88811d6b3428 FS: 00007fc82e18ae80(0000) GS:ffff88842e080000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f9630d1b421 CR3: 0000000149802004 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> mlx5_esw_offloads_devcom_event+0x99/0x3b0 [mlx5_core] mlx5_devcom_send_event+0x167/0x1d0 [mlx5_core] esw_offloads_enable+0x1153/0x1500 [mlx5_core] ? mlx5_esw_offloads_controller_valid+0x170/0x170 [mlx5_core] ? wait_for_completion_io_timeout+0x20/0x20 ? mlx5_rescan_drivers_locked+0x318/0x810 [mlx5_core] mlx5_eswitch_enable_locked+0x586/0xc50 [mlx5_core] ? mlx5_eswitch_disable_pf_vf_vports+0x1d0/0x1d0 [mlx5_core] ? mlx5_esw_try_lock+0x1b/0xb0 [mlx5_core] ? mlx5_eswitch_enable+0x270/0x270 [mlx5_core] ? __debugfs_create_file+0x260/0x3e0 mlx5_devlink_eswitch_mode_set+0x27e/0x870 [mlx5_core] ? mutex_lock_io_nested+0x12c0/0x12c0 ? esw_offloads_disable+0x250/0x250 [mlx5_core] ? devlink_nl_cmd_trap_get_dumpit+0x470/0x470 ? rcu_read_lock_sched_held+0x3f/0x70 devlink_nl_cmd_eswitch_set_doit+0x217/0x620

In the Linux kernel, the following vulnerability has been resolved: erofs: fix out-of-bound access when z_erofs_gbuf_growsize() partially fails If z_erofs_gbuf_growsize() partially fails on a global buffer due to memory allocation failure or fault injection (as reported by syzbot [1]), new pages need to be freed by comparing to the existing pages to avoid memory leaks. However, the old gbuf->pages[] array may not be large enough, which can lead to null-ptr-deref or out-of-bound access. Fix this by checking against gbuf->nrpages in advance. [1] https://lore.kernel.org/r/000000000000f7b96e062018c6e3@google.com

In the Linux kernel, the following vulnerability has been resolved: RDMA/hfi1: fix potential memory leak in setup_base_ctxt() setup_base_ctxt() allocates a memory chunk for uctxt->groups with hfi1_alloc_ctxt_rcv_groups(). When init_user_ctxt() fails, uctxt->groups is not released, which will lead to a memory leak. We should release the uctxt->groups with hfi1_free_ctxt_rcv_groups() when init_user_ctxt() fails.

In the Linux kernel, the following vulnerability has been resolved: smb/client: avoid dereferencing rdata=NULL in smb2_new_read_req() This happens when called from SMB2_read() while using rdma and reaching the rdma_readwrite_threshold.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix the waring dereferencing hive Check the amdgpu_hive_info *hive that maybe is NULL.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Make ICC_*SGI*_EL1 undef in the absence of a vGICv3 On a system with a GICv3, if a guest hasn't been configured with GICv3 and that the host is not capable of GICv2 emulation, a write to any of the ICC_*SGI*_EL1 registers is trapped to EL2. We therefore try to emulate the SGI access, only to hit a NULL pointer as no private interrupt is allocated (no GIC, remember?). The obvious fix is to give the guest what it deserves, in the shape of a UNDEF exception.

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp - Use kzalloc for sev ioctl interfaces to prevent kernel memory leak For some sev ioctl interfaces, input may be passed that is less than or equal to SEV_FW_BLOB_MAX_SIZE, but larger than the data that PSP firmware returns. In this case, kmalloc will allocate memory that is the size of the input rather than the size of the data. Since PSP firmware doesn't fully overwrite the buffer, the sev ioctl interfaces with the issue may return uninitialized slab memory. Currently, all of the ioctl interfaces in the ccp driver are safe, but to prevent future problems, change all ioctl interfaces that allocate memory with kmalloc to use kzalloc and memset the data buffer to zero in sev_ioctl_do_platform_status.

In the Linux kernel, the following vulnerability has been resolved: sctp: initialize more fields in sctp_v6_from_sk() syzbot found that sin6_scope_id was not properly initialized, leading to undefined behavior. Clear sin6_scope_id and sin6_flowinfo. BUG: KMSAN: uninit-value in __sctp_v6_cmp_addr+0x887/0x8c0 net/sctp/ipv6.c:649 __sctp_v6_cmp_addr+0x887/0x8c0 net/sctp/ipv6.c:649 sctp_inet6_cmp_addr+0x4f2/0x510 net/sctp/ipv6.c:983 sctp_bind_addr_conflict+0x22a/0x3b0 net/sctp/bind_addr.c:390 sctp_get_port_local+0x21eb/0x2440 net/sctp/socket.c:8452 sctp_get_port net/sctp/socket.c:8523 [inline] sctp_listen_start net/sctp/socket.c:8567 [inline] sctp_inet_listen+0x710/0xfd0 net/sctp/socket.c:8636 __sys_listen_socket net/socket.c:1912 [inline] __sys_listen net/socket.c:1927 [inline] __do_sys_listen net/socket.c:1932 [inline] __se_sys_listen net/socket.c:1930 [inline] __x64_sys_listen+0x343/0x4c0 net/socket.c:1930 x64_sys_call+0x271d/0x3e20 arch/x86/include/generated/asm/syscalls_64.h:51 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xd9/0x210 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f Local variable addr.i.i created at: sctp_get_port net/sctp/socket.c:8515 [inline] sctp_listen_start net/sctp/socket.c:8567 [inline] sctp_inet_listen+0x650/0xfd0 net/sctp/socket.c:8636 __sys_listen_socket net/socket.c:1912 [inline] __sys_listen net/socket.c:1927 [inline] __do_sys_listen net/socket.c:1932 [inline] __se_sys_listen net/socket.c:1930 [inline] __x64_sys_listen+0x343/0x4c0 net/socket.c:1930

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Handle mailbox timeouts in lpfc_get_sfp_info The MBX_TIMEOUT return code is not handled in lpfc_get_sfp_info and the routine unconditionally frees submitted mailbox commands regardless of return status. The issue is that for MBX_TIMEOUT cases, when firmware returns SFP information at a later time, that same mailbox memory region references previously freed memory in its cmpl routine. Fix by adding checks for the MBX_TIMEOUT return code. During mailbox resource cleanup, check the mbox flag to make sure that the wait did not timeout. If the MBOX_WAKE flag is not set, then do not free the resources because it will be freed when firmware completes the mailbox at a later time in its cmpl routine. Also, increase the timeout from 30 to 60 seconds to accommodate boot scripts requiring longer timeouts.