An issue was discovered in the Linux kernel 4.18 through 5.10.16, as used by Xen. The backend allocation (aka be-alloc) mode of the drm_xen_front drivers was not meant to be a supported configuration, but this wasn't stated accordingly in its support status entry.

An issue was discovered in the Linux kernel 3.11 through 5.10.16, as used by Xen. To service requests to the PV backend, the driver maps grant references provided by the frontend. In this process, errors may be encountered. In one case, an error encountered earlier might be discarded by later processing, resulting in the caller assuming successful mapping, and hence subsequent operations trying to access space that wasn't mapped. In another case, internal state would be insufficiently updated, preventing safe recovery from the error. This affects drivers/block/xen-blkback/blkback.c.

In the Linux kernel, the following vulnerability has been resolved: PCI: s390: Fix use-after-free of PCI resources with per-function hotplug On s390 PCI functions may be hotplugged individually even when they belong to a multi-function device. In particular on an SR-IOV device VFs may be removed and later re-added. In commit a50297cf8235 ("s390/pci: separate zbus creation from scanning") it was missed however that struct pci_bus and struct zpci_bus's resource list retained a reference to the PCI functions MMIO resources even though those resources are released and freed on hot-unplug. These stale resources may subsequently be claimed when the PCI function re-appears resulting in use-after-free. One idea of fixing this use-after-free in s390 specific code that was investigated was to simply keep resources around from the moment a PCI function first appeared until the whole virtual PCI bus created for a multi-function device disappears. The problem with this however is that due to the requirement of artificial MMIO addreesses (address cookies) extra logic is then needed to keep the address cookies compatible on re-plug. At the same time the MMIO resources semantically belong to the PCI function so tying their lifecycle to the function seems more logical. Instead a simpler approach is to remove the resources of an individually hot-unplugged PCI function from the PCI bus's resource list while keeping the resources of other PCI functions on the PCI bus untouched. This is done by introducing pci_bus_remove_resource() to remove an individual resource. Similarly the resource also needs to be removed from the struct zpci_bus's resource list. It turns out however, that there is really no need to add the MMIO resources to the struct zpci_bus's resource list at all and instead we can simply use the zpci_bar_struct's resource pointer directly.

An issue was discovered in the Linux kernel through 5.11.3. Certain iSCSI data structures do not have appropriate length constraints or checks, and can exceed the PAGE_SIZE value. An unprivileged user can send a Netlink message that is associated with iSCSI, and has a length up to the maximum length of a Netlink message.

Improper input validation in NI-PAL may allow a local authenticated user to access arbitrary system memory, potentially leading to privilege escalation. This vulnerability affects NI-PAL 26.3.0 and prior versions on Windows and Linux.

kernel/trace/trace_syscalls.c in the Linux kernel through 3.17.2 does not properly handle private syscall numbers during use of the ftrace subsystem, which allows local users to gain privileges or cause a denial of service (invalid pointer dereference) via a crafted application.

In the Linux kernel, the following vulnerability has been resolved: io-wq: check that the predecessor is hashed in io_wq_remove_pending() io_wq_remove_pending() needs to fix up wq->hash_tail[] if the cancelled work was the tail of its hash bucket. When doing this, it checks whether the preceding entry in acct->work_list has the same hash value, but never checks that the predecessor is hashed at all. io_get_work_hash() is simply atomic_read(&work->flags) >> IO_WQ_HASH_SHIFT, and the hash bits are never set for non-hashed work, so it returns 0. Thus, when a hashed bucket-0 work is cancelled while a non-hashed work is its list predecessor, the check spuriously passes and a pointer to the non-hashed io_kiocb is stored in wq->hash_tail[0]. Because non-hashed work is dequeued via the fast path in io_get_next_work(), which never touches hash_tail[], the stale pointer is never cleared. Therefore, after the non-hashed io_kiocb completes and is freed back to req_cachep, wq->hash_tail[0] is a dangling pointer. The io_wq is per-task (tctx->io_wq) and survives ring open/close, so the dangling pointer persists for the lifetime of the task; the next hashed bucket-0 enqueue dereferences it in io_wq_insert_work() and wq_list_add_after() writes through freed memory. Add the missing io_wq_is_hashed() check so a non-hashed predecessor never inherits a hash_tail[] slot.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer Dereference (NPD) conditions were observed in the lifecycle management of hci_uart. The primary issue arises because the workqueues (init_ready and write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY flag is set during TTY close. If a hangup occurs before setup completes, hci_uart_tty_close() skips the teardown of these workqueues and proceeds to free the `hu` struct. When the scheduled work executes later, it blindly dereferences the freed `hu` struct. Furthermore, several data races and UAFs were identified in the teardown sequence: 1. Calling hci_uart_flush() from hci_uart_close() without effectively disabling write_work causes a race condition where both can concurrently double-free hu->tx_skb. This happens because protocol timers can concurrently invoke hci_uart_tx_wakeup() and requeue write_work. 2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF when vendor specific protocol close callbacks dereference hu->hdev. 3. In the initialization error paths, failing to take the proto_lock write lock before clearing PROTO_READY leads to races with active readers. Additionally, hci_uart_tty_receive() accesses hu->hdev outside the read lock, leading to UAFs if the initialization error path frees hdev concurrently. Fix these synchronization and lifecycle issues by: 1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first, followed immediately by a cancel_work_sync(&hu->write_work). Clearing the flag locks out concurrent protocol timers from successfully invoking hci_uart_tx_wakeup(), effectively rendering the cancellation permanent and preventing the tx_skb double-free. 2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip hu->proto->flush(). This is perfectly safe in the tty_close path because hu->proto->close() executes shortly after, which intrinsically purges all protocol SKB queues and tears down the state. 3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev) across all close and error paths to prevent vendor-level UAFs. 4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive() inside the proto_lock read-side critical section to safely synchronize with device unregistration. 5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely flush the workqueue before hci_uart_flush() is invoked via the HCI core. 6. Utilizing cancel_work_sync() instead of disable_work_sync() across all paths to prevent permanently breaking user-space retry capabilities.

The Linux kernel before 2.6.25.10 does not properly perform tty operations, which allows local users to cause a denial of service (system crash) or possibly gain privileges via vectors involving NULL pointer dereference of function pointers in (1) hamradio/6pack.c, (2) hamradio/mkiss.c, (3) irda/irtty-sir.c, (4) ppp_async.c, (5) ppp_synctty.c, (6) slip.c, (7) wan/x25_asy.c, and (8) wireless/strip.c in drivers/net/.

Use After Free vulnerability in nfc sockets in the Linux Kernel before 5.12.4 allows local attackers to elevate their privileges. In typical configurations, the issue can only be triggered by a privileged local user with the CAP_NET_RAW capability.

A heap out-of-bounds write affecting Linux since v2.6.19-rc1 was discovered in net/netfilter/x_tables.c. This allows an attacker to gain privileges or cause a DoS (via heap memory corruption) through user name space

In the Linux kernel, the following vulnerability has been resolved: mm/zone_device: do not touch device folio after calling ->folio_free() The contents of a device folio can immediately change after calling ->folio_free(), as the folio may be reallocated by a driver with a different order. Instead of touching the folio again to extract the pgmap, use the local stack variable when calling percpu_ref_put_many().

An issue was discovered in Linux: KVM through Improper handling of VM_IO|VM_PFNMAP vmas in KVM can bypass RO checks and can lead to pages being freed while still accessible by the VMM and guest. This allows users with the ability to start and control a VM to read/write random pages of memory and can result in local privilege escalation.

In the Linux kernel, the following vulnerability has been resolved: lib: test_hmm: evict device pages on file close to avoid use-after-free Patch series "Minor hmm_test fixes and cleanups". Two bugfixes a cleanup for the HMM kernel selftests. These were mostly reported by Zenghui Yu with special thanks to Lorenzo for analysing and pointing out the problems. This patch (of 3): When dmirror_fops_release() is called it frees the dmirror struct but doesn't migrate device private pages back to system memory first. This leaves those pages with a dangling zone_device_data pointer to the freed dmirror. If a subsequent fault occurs on those pages (eg. during coredump) the dmirror_devmem_fault() callback dereferences the stale pointer causing a kernel panic. This was reported [1] when running mm/ksft_hmm.sh on arm64, where a test failure triggered SIGABRT and the resulting coredump walked the VMAs faulting in the stale device private pages. Fix this by calling dmirror_device_evict_chunk() for each devmem chunk in dmirror_fops_release() to migrate all device private pages back to system memory before freeing the dmirror struct. The function is moved earlier in the file to avoid a forward declaration.

In the Linux kernel, the following vulnerability has been resolved: vmalloc: fix buffer overflow in vrealloc_node_align() Commit 4c5d3365882d ("mm/vmalloc: allow to set node and align in vrealloc") added the ability to force a new allocation if the current pointer is on the wrong NUMA node, or if an alignment constraint is not met, even if the user is shrinking the allocation. On this path (need_realloc), the code allocates a new object of 'size' bytes and then memcpy()s 'old_size' bytes into it. If the request is to shrink the object (size < old_size), this results in an out-of-bounds write on the new buffer. Fix this by bounding the copy length by the new allocation size.

In the Linux kernel, the following vulnerability has been resolved: mtd: docg3: fix use-after-free in docg3_release() In docg3_release(), the docg3 pointer is obtained from cascade->floors[0]->priv before the loop that calls doc_release_device() on each floor. doc_release_device() frees the docg3 struct via kfree(docg3) at line 1881. After the loop, docg3->cascade->bch dereferences the already-freed pointer. Fix this by accessing cascade->bch directly, which is equivalent since docg3->cascade points back to the same cascade struct, and is already available as a local variable. This also removes the now-unused docg3 local variable.

In the Linux kernel, the following vulnerability has been resolved: dm: fix a buffer overflow in ioctl processing Tony Asleson (using Claude) found a buffer overflow in dm-ioctl in the function retrieve_status: 1. The code in retrieve_status checks that the output string fits into the output buffer and writes the output string there 2. Then, the code aligns the "outptr" variable to the next 8-byte boundary: outptr = align_ptr(outptr); 3. The alignment doesn't check overflow, so outptr could point past the buffer end 4. The "for" loop is iterated again, it executes: remaining = len - (outptr - outbuf); 5. If "outptr" points past "outbuf + len", the arithmetics wraps around and the variable "remaining" contains unusually high number 6. With "remaining" being high, the code writes more data past the end of the buffer Luckily, this bug has no security implications because: 1. Only root can issue device mapper ioctls 2. The commonly used libraries that communicate with device mapper (libdevmapper and devicemapper-rs) use buffer size that is aligned to 8 bytes - thus, "outptr = align_ptr(outptr)" can't overshoot the input buffer and the bug can't happen accidentally

In the Linux kernel, the following vulnerability has been resolved: spi: topcliff-pch: fix use-after-free on unbind Give the driver a chance to flush its queue before releasing the DMA buffers on driver unbind

In the Linux kernel, the following vulnerability has been resolved: pmdomain: mediatek: fix use-after-free in scpsys_get_bus_protection_legacy() In scpsys_get_bus_protection_legacy(), of_find_node_with_property() returns a device node with its reference count incremented. The function then calls of_node_put(node) before checking whether syscon_regmap_lookup_by_phandle() returns an error. If an error occurs, dev_err_probe() dereferences the node pointer to print diagnostic information, but the node memory may have already been freed due to the earlier of_node_put(), leading to a use-after-free vulnerability. Fix this by moving the of_node_put() call after the error check, ensuring the node is still valid when accessed in the error path.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/userq: fix access to stale wptr mapping Use drm_exec to take both locks i.e vm root bo and wptr_obj bo to access the mapping data properly. This fixes the security issue of unmap the wptr_obj while a queue creation is in progress and passing other bo at same address. (cherry picked from commit 1fc6c8ab45dbee096469c08c13f6099d57a52d6c)

The installation directory of LogStare Collector is configured with incorrect access permissions. A non-administrative user may manipulate files within the installation directory and execute arbitrary code with the administrative privilege.

A use-after-free flaw was found in the io_uring in Linux kernel, where a local attacker with a user privilege could cause a denial of service problem on the system The issue results from the lack of validating the existence of an object prior to performing operations on the object by not incrementing the file reference counter while in use. The highest threat from this vulnerability is to data integrity, confidentiality and system availability.

In the Linux kernel, the following vulnerability has been resolved: xsk: cache csum_start/csum_offset to fix TOCTOU in xsk_skb_metadata() The TX metadata area resides in the UMEM buffer which is memory-mapped and concurrently writable by userspace. In xsk_skb_metadata(), csum_start and csum_offset are read from shared memory for bounds validation, then read again for skb assignment. A malicious userspace application can race to overwrite these values between the two reads, bypassing the bounds check and causing out-of-bounds memory access during checksum computation in the transmit path. Fix this by reading csum_start and csum_offset into local variables once, then using the local copies for both validation and assignment. Note that other metadata fields (flags, launch_time) and the cached csum fields may be mutually inconsistent due to concurrent userspace writes, but this is benign: the only security-critical invariant is that each field's validated value is the same one used, which local caching guarantees.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: avoid double drm_exec_fini() in userq validate When new_addition is true, amdgpu_userq_vm_validate() calls drm_exec_fini(&exec) before iterating over the collected HMM ranges and calling amdgpu_ttm_tt_get_user_pages(). If amdgpu_ttm_tt_get_user_pages() fails in that path, the code jumps to unlock_all and calls drm_exec_fini(&exec) a second time on the same exec object. drm_exec_fini() is not idempotent: it frees exec->objects and may also drop exec->contended and finalize the ww acquire context. Route that error path directly to the range cleanup once exec has already been finalized. Issue found using a prototype static analysis tool and confirmed by code review. (cherry picked from commit 2802952e4a07306da6ebe813ff1acacc5691851a)

In the Linux kernel, the following vulnerability has been resolved: quota: Fix race of dquot_scan_active() with quota deactivation dquot_scan_active() can race with quota deactivation in quota_release_workfn() like: CPU0 (quota_release_workfn) CPU1 (dquot_scan_active) ============================== ============================== spin_lock(&dq_list_lock); list_replace_init( &releasing_dquots, &rls_head); /* dquot X on rls_head, dq_count == 0, DQ_ACTIVE_B still set */ spin_unlock(&dq_list_lock); synchronize_srcu(&dquot_srcu); spin_lock(&dq_list_lock); list_for_each_entry(dquot, &inuse_list, dq_inuse) { /* finds dquot X */ dquot_active(X) -> true atomic_inc(&X->dq_count); } spin_unlock(&dq_list_lock); spin_lock(&dq_list_lock); dquot = list_first_entry(&rls_head); WARN_ON_ONCE(atomic_read(&dquot->dq_count)); The problem is not only a cosmetic one as under memory pressure the caller of dquot_scan_active() can end up working on freed dquot. Fix the problem by making sure the dquot is removed from releasing list when we acquire a reference to it.

In the Linux kernel, the following vulnerability has been resolved: l2tp: pppol2tp: hold reference to session in pppol2tp_ioctl() pppol2tp_ioctl() read sock->sk->sk_user_data directly without any locks or reference counting. If a controllable sleep was induced during copy_from_user() (e.g. via a userfaultfd page fault sleep), a concurrent socket close could trigger pppol2tp_session_close() asynchronously. This frees the l2tp_session structure via the l2tp_session_del_work workqueue. Upon resuming, the ioctl thread dereferences the stale session pointer, resulting in a Use-After-Free (UAF). Fix this by securely fetching the session reference using the RCU-safe, refcounted helper pppol2tp_sock_to_session(sk) on entry. This locks the session's refcount across the sleep. We structured the function to exit via standard err breaks, guaranteeing that l2tp_session_put() is cleanly called on all return paths to drop the reference. To preserve existing behavior we validate the session and its magic signature only for the specific L2TP commands that require it. This ensures that generic/unknown ioctls called on an unconnected socket still return -ENOIOCTLCMD and correctly fall back to generic handlers (e.g. in sock_do_ioctl()).

Privilege Escalation vulnerability in McAfee Active Response (MAR) for Linux prior to 2.4.3 Hotfix 1 allows a malicious script or program to perform functions that the local executing user has not been granted access to.

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Fix timeline left held on VMA alloc error The following error has been reported sporadically by CI when a test unbinds the i915 driver on a ring submission platform: <4> [239.330153] ------------[ cut here ]------------ <4> [239.330166] i915 0000:00:02.0: [drm] drm_WARN_ON(dev_priv->mm.shrink_count) <4> [239.330196] WARNING: CPU: 1 PID: 18570 at drivers/gpu/drm/i915/i915_gem.c:1309 i915_gem_cleanup_early+0x13e/0x150 [i915] ... <4> [239.330640] RIP: 0010:i915_gem_cleanup_early+0x13e/0x150 [i915] ... <4> [239.330942] Call Trace: <4> [239.330944] <TASK> <4> [239.330949] i915_driver_late_release+0x2b/0xa0 [i915] <4> [239.331202] i915_driver_release+0x86/0xa0 [i915] <4> [239.331482] devm_drm_dev_init_release+0x61/0x90 <4> [239.331494] devm_action_release+0x15/0x30 <4> [239.331504] release_nodes+0x3d/0x120 <4> [239.331517] devres_release_all+0x96/0xd0 <4> [239.331533] device_unbind_cleanup+0x12/0x80 <4> [239.331543] device_release_driver_internal+0x23a/0x280 <4> [239.331550] ? bus_find_device+0xa5/0xe0 <4> [239.331563] device_driver_detach+0x14/0x20 ... <4> [357.719679] ---[ end trace 0000000000000000 ]--- If the test also unloads the i915 module then that's followed with: <3> [357.787478] ============================================================================= <3> [357.788006] BUG i915_vma (Tainted: G U W N ): Objects remaining on __kmem_cache_shutdown() <3> [357.788031] ----------------------------------------------------------------------------- <3> [357.788204] Object 0xffff888109e7f480 @offset=29824 <3> [357.788670] Allocated in i915_vma_instance+0xee/0xc10 [i915] age=292729 cpu=4 pid=2244 <4> [357.788994] i915_vma_instance+0xee/0xc10 [i915] <4> [357.789290] init_status_page+0x7b/0x420 [i915] <4> [357.789532] intel_engines_init+0x1d8/0x980 [i915] <4> [357.789772] intel_gt_init+0x175/0x450 [i915] <4> [357.790014] i915_gem_init+0x113/0x340 [i915] <4> [357.790281] i915_driver_probe+0x847/0xed0 [i915] <4> [357.790504] i915_pci_probe+0xe6/0x220 [i915] ... Closer analysis of CI results history has revealed a dependency of the error on a few IGT tests, namely: - igt@api_intel_allocator@fork-simple-stress-signal, - igt@api_intel_allocator@two-level-inception-interruptible, - igt@gem_linear_blits@interruptible, - igt@prime_mmap_coherency@ioctl-errors, which invisibly trigger the issue, then exhibited with first driver unbind attempt. All of the above tests perform actions which are actively interrupted with signals. Further debugging has allowed to narrow that scope down to DRM_IOCTL_I915_GEM_EXECBUFFER2, and ring_context_alloc(), specific to ring submission, in particular. If successful then that function, or its execlists or GuC submission equivalent, is supposed to be called only once per GEM context engine, followed by raise of a flag that prevents the function from being called again. The function is expected to unwind its internal errors itself, so it may be safely called once more after it returns an error. In case of ring submission, the function first gets a reference to the engine's legacy timeline and then allocates a VMA. If the VMA allocation fails, e.g. when i915_vma_instance() called from inside is interrupted with a signal, then ring_context_alloc() fails, leaving the timeline held referenced. On next I915_GEM_EXECBUFFER2 IOCTL, another reference to the timeline is got, and only that last one is put on successful completion. As a consequence, the legacy timeline, with its underlying engine status page's VMA object, is still held and not released on driver unbind. Get the legacy timeline only after successful allocation of the context engine's VMA. v2: Add a note on other submission methods (Krzysztof Karas): Both execlists and GuC submission use lrc_alloc() which seems free from a similar issue. (cherry picked from commit cc43422b3cc79eacff4c5a8ba0d224688ca9dd4f)

In the Linux kernel, the following vulnerability has been resolved: powerpc64/ftrace: fix clobbered r15 during livepatching While r15 is clobbered always with PPC_FTRACE_OUT_OF_LINE, it is not restored in livepatch sequence leading to not so obvious fails like below: BUG: Unable to handle kernel data access on write at 0xc0000000000f9078 Faulting instruction address: 0xc0000000018ff958 Oops: Kernel access of bad area, sig: 11 [#1] ... NIP: c0000000018ff958 LR: c0000000018ff930 CTR: c0000000009c0790 REGS: c00000005f2e7790 TRAP: 0300 Tainted: G K (6.14.0+) MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE> CR: 2822880b XER: 20040000 CFAR: c0000000008addc0 DAR: c0000000000f9078 DSISR: 0a000000 IRQMASK: 1 GPR00: c0000000018f2584 c00000005f2e7a30 c00000000280a900 c000000017ffa488 GPR04: 0000000000000008 0000000000000000 c0000000018f24fc 000000000000000d GPR08: fffffffffffe0000 000000000000000d 0000000000000000 0000000000008000 GPR12: c0000000009c0790 c000000017ffa480 c00000005f2e7c78 c0000000000f9070 GPR16: c00000005f2e7c90 0000000000000000 0000000000000000 0000000000000000 GPR20: 0000000000000000 c00000005f3efa80 c00000005f2e7c60 c00000005f2e7c88 GPR24: c00000005f2e7c60 0000000000000001 c0000000000f9078 0000000000000000 GPR28: 00007fff97960000 c000000017ffa480 0000000000000000 c0000000000f9078 ... Call Trace: check_heap_object+0x34/0x390 (unreliable) __mutex_unlock_slowpath.isra.0+0xe4/0x230 seq_read_iter+0x430/0xa90 proc_reg_read_iter+0xa4/0x200 vfs_read+0x41c/0x510 ksys_read+0xa4/0x190 system_call_exception+0x1d0/0x440 system_call_vectored_common+0x15c/0x2ec Fix it by restoring r15 always.

In the Linux kernel, the following vulnerability has been resolved: net: usb: lan78xx: fix WARN in __netif_napi_del_locked on disconnect Remove redundant netif_napi_del() call from disconnect path. A WARN may be triggered in __netif_napi_del_locked() during USB device disconnect: WARNING: CPU: 0 PID: 11 at net/core/dev.c:7417 __netif_napi_del_locked+0x2b4/0x350 This happens because netif_napi_del() is called in the disconnect path while NAPI is still enabled. However, it is not necessary to call netif_napi_del() explicitly, since unregister_netdev() will handle NAPI teardown automatically and safely. Removing the redundant call avoids triggering the warning. Full trace: lan78xx 1-1:1.0 enu1: Failed to read register index 0x000000c4. ret = -ENODEV lan78xx 1-1:1.0 enu1: Failed to set MAC down with error -ENODEV lan78xx 1-1:1.0 enu1: Link is Down lan78xx 1-1:1.0 enu1: Failed to read register index 0x00000120. ret = -ENODEV ------------[ cut here ]------------ WARNING: CPU: 0 PID: 11 at net/core/dev.c:7417 __netif_napi_del_locked+0x2b4/0x350 Modules linked in: flexcan can_dev fuse CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 6.16.0-rc2-00624-ge926949dab03 #9 PREEMPT Hardware name: SKOV IMX8MP CPU revC - bd500 (DT) Workqueue: usb_hub_wq hub_event pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __netif_napi_del_locked+0x2b4/0x350 lr : __netif_napi_del_locked+0x7c/0x350 sp : ffffffc085b673c0 x29: ffffffc085b673c0 x28: ffffff800b7f2000 x27: ffffff800b7f20d8 x26: ffffff80110bcf58 x25: ffffff80110bd978 x24: 1ffffff0022179eb x23: ffffff80110bc000 x22: ffffff800b7f5000 x21: ffffff80110bc000 x20: ffffff80110bcf38 x19: ffffff80110bcf28 x18: dfffffc000000000 x17: ffffffc081578940 x16: ffffffc08284cee0 x15: 0000000000000028 x14: 0000000000000006 x13: 0000000000040000 x12: ffffffb0022179e8 x11: 1ffffff0022179e7 x10: ffffffb0022179e7 x9 : dfffffc000000000 x8 : 0000004ffdde8619 x7 : ffffff80110bcf3f x6 : 0000000000000001 x5 : ffffff80110bcf38 x4 : ffffff80110bcf38 x3 : 0000000000000000 x2 : 0000000000000000 x1 : 1ffffff0022179e7 x0 : 0000000000000000 Call trace: __netif_napi_del_locked+0x2b4/0x350 (P) lan78xx_disconnect+0xf4/0x360 usb_unbind_interface+0x158/0x718 device_remove+0x100/0x150 device_release_driver_internal+0x308/0x478 device_release_driver+0x1c/0x30 bus_remove_device+0x1a8/0x368 device_del+0x2e0/0x7b0 usb_disable_device+0x244/0x540 usb_disconnect+0x220/0x758 hub_event+0x105c/0x35e0 process_one_work+0x760/0x17b0 worker_thread+0x768/0xce8 kthread+0x3bc/0x690 ret_from_fork+0x10/0x20 irq event stamp: 211604 hardirqs last enabled at (211603): [<ffffffc0828cc9ec>] _raw_spin_unlock_irqrestore+0x84/0x98 hardirqs last disabled at (211604): [<ffffffc0828a9a84>] el1_dbg+0x24/0x80 softirqs last enabled at (211296): [<ffffffc080095f10>] handle_softirqs+0x820/0xbc8 softirqs last disabled at (210993): [<ffffffc080010288>] __do_softirq+0x18/0x20 ---[ end trace 0000000000000000 ]--- lan78xx 1-1:1.0 enu1: failed to kill vid 0081/0

IBM DB2 for Linux, UNIX and Windows (includes DB2 Connect Server) 9.7, 10.1, 10.5, 11.1, and 11.5 db2fm is vulnerable to a buffer overflow, caused by improper bounds checking which could allow a local attacker to execute arbitrary code on the system with root privileges. IBM X-Force ID: 193661.

The futex_requeue function in kernel/futex.c in the Linux kernel through 3.14.5 does not ensure that calls have two different futex addresses, which allows local users to gain privileges via a crafted FUTEX_REQUEUE command that facilitates unsafe waiter modification.

In the Linux kernel, the following vulnerability has been resolved: ceph: fix a buffer leak in __ceph_setxattr() The old_blob in __ceph_setxattr() can store ci->i_xattrs.prealloc_blob value during the retry. However, it is never called the ceph_buffer_put() for the old_blob object. This patch fixes the issue of the buffer leak.

In the Linux kernel, the following vulnerability has been resolved: USB: serial: io_ti: fix heap overflow in build_i2c_fw_hdr() build_i2c_fw_hdr() allocates a fixed-size buffer of (16*1024 - 512) + sizeof(struct ti_i2c_firmware_rec) bytes, then copies le16_to_cpu(img_header->Length) bytes into it without validating that Length fits within the available space after the firmware record header. img_header->Length is a __le16 from the firmware file and can be up to 65535. check_fw_sanity() validates the total firmware size but not img_header->Length specifically. Fix by rejecting images where img_header->Length exceeds the available destination space.

In the Linux kernel, the following vulnerability has been resolved: tee: optee: prevent use-after-free when the client exits before the supplicant Commit 70b0d6b0a199 ("tee: optee: Fix supplicant wait loop") made the client wait as killable so it can be interrupted during shutdown or after a supplicant crash. This changes the original lifetime expectations: the client task can now terminate while the supplicant is still processing its request. If the client exits first it removes the request from its queue and kfree()s it, while the request ID remains in supp->idr. A subsequent lookup on the supplicant path then dereferences freed memory, leading to a use-after-free. Serialise access to the request with supp->mutex: * Hold supp->mutex in optee_supp_recv() and optee_supp_send() while looking up and touching the request. * Let optee_supp_thrd_req() notice that the client has terminated and signal optee_supp_send() accordingly. With these changes the request cannot be freed while the supplicant still has a reference, eliminating the race.

In the Linux kernel, the following vulnerability has been resolved: drm/xe/eustall: Fix drm_dev_put called before stream disable in close In xe_eu_stall_stream_close(), drm_dev_put() is called before the stream is disabled and its resources are freed. If this drops the last reference, the device structures could be freed while the subsequent cleanup code still accesses them, leading to a use-after-free. Fix this by moving drm_dev_put() after all device accesses are complete. This matches the ordering in xe_oa_release(). (cherry picked from commit 35aff528f7297e949e5e19c9cd7fd748cf1cf21c)

IBM DB2 for Linux, UNIX and Windows (includes DB2 Connect Server) 9.7, 10.1, 10.5, 11.1, and 11.5 is vulnerable to a buffer overflow, caused by improper bounds checking which could allow a local attacker to execute arbitrary code on the system with root privileges. IBM X-Force ID: 174960.

In the Linux kernel, the following vulnerability has been resolved: bpf: Free reuseport cBPF prog after RCU grace period. Eulgyu Kim reported the splat below with a repro. [0] The repro sets up a UDP reuseport group with a cBPF prog and replaces it with a new one while another thread is sending a UDP packet to the group. The reuseport prog is freed by sk_reuseport_prog_free(). bpf_prog_put() is called for "e"BPF prog to destruct through multiple stages while cBPF prog is freed immediately by bpf_release_orig_filter() and bpf_prog_free(). If a reuseport prog is detached from the setsockopt() path (reuseport_attach_prog() or reuseport_detach_prog()), sk_reuseport_prog_free() is called without waiting for RCU readers to complete, resulting in various bugs. Let's defer freeing the reuseport cBPF prog after one RCU grace period. Note "e"BPF prog is safe as is unless the fast path starts to touch fields destroyed in bpf_prog_put_deferred() and __bpf_prog_put_noref(). [0]: BUG: KASAN: vmalloc-out-of-bounds in reuseport_select_sock+0xedc/0x1220 net/core/sock_reuseport.c:596 Read of size 4 at addr ffffc9000051e004 by task slowme/10208 CPU: 6 UID: 1000 PID: 10208 Comm: slowme Not tainted 7.0.0-geb7ac95ff75e #32 PREEMPT(full) Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <IRQ> dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0xca/0x240 mm/kasan/report.c:482 kasan_report+0x118/0x150 mm/kasan/report.c:595 reuseport_select_sock+0xedc/0x1220 net/core/sock_reuseport.c:596 udp4_lib_lookup2+0x3bc/0x950 net/ipv4/udp.c:495 __udp4_lib_lookup+0x768/0xe20 net/ipv4/udp.c:723 __udp4_lib_lookup_skb+0x297/0x390 net/ipv4/udp.c:752 __udp4_lib_rcv+0x1312/0x2620 net/ipv4/udp.c:2752 ip_protocol_deliver_rcu+0x282/0x440 net/ipv4/ip_input.c:207 ip_local_deliver_finish+0x3bb/0x6f0 net/ipv4/ip_input.c:241 NF_HOOK+0x30c/0x3a0 include/linux/netfilter.h:318 NF_HOOK+0x30c/0x3a0 include/linux/netfilter.h:318 __netif_receive_skb_one_core net/core/dev.c:6181 [inline] __netif_receive_skb net/core/dev.c:6294 [inline] process_backlog+0xaa4/0x1960 net/core/dev.c:6645 __napi_poll+0xae/0x340 net/core/dev.c:7709 napi_poll net/core/dev.c:7772 [inline] net_rx_action+0x5d7/0xf50 net/core/dev.c:7929 handle_softirqs+0x22b/0x870 kernel/softirq.c:622 do_softirq+0x76/0xd0 kernel/softirq.c:523 </IRQ> <TASK> __local_bh_enable_ip+0xf8/0x130 kernel/softirq.c:450 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:924 [inline] __dev_queue_xmit+0x1dd7/0x3710 net/core/dev.c:4890 neigh_output include/net/neighbour.h:556 [inline] ip_finish_output2+0xca9/0x1070 net/ipv4/ip_output.c:237 NF_HOOK_COND include/linux/netfilter.h:307 [inline] ip_output+0x29f/0x450 net/ipv4/ip_output.c:438 ip_send_skb+0x45/0xc0 net/ipv4/ip_output.c:1508 udp_send_skb+0xb04/0x1510 net/ipv4/udp.c:1195 udp_sendmsg+0x1a71/0x2350 net/ipv4/udp.c:1485 sock_sendmsg_nosec net/socket.c:727 [inline] __sock_sendmsg net/socket.c:742 [inline] __sys_sendto+0x554/0x680 net/socket.c:2206 __do_sys_sendto net/socket.c:2213 [inline] __se_sys_sendto net/socket.c:2209 [inline] __x64_sys_sendto+0xde/0x100 net/socket.c:2209 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0x160/0xf80 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x415a2d Code: b3 66 2e 0f 1f 84 00 00 00 00 00 66 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f6bc31e41e8 EFLAGS: 00000212 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007f6bc31e4cdc RCX: 0000000000415a2d RDX: 0000000000000001 RSI: 00007f6bc31e421f RDI: 0000000000000003 RBP: 00007f6bc31e4240 R08: 00007f6bc31e4220 R09: 0000000000000010 R10: 0000000000000000 R11: ---truncated---

IBM DB2 for Linux, UNIX and Windows (includes DB2 Connect Server) 9.7, 10.1, 10.5, 11.1, and 11.5 is vulnerable to a buffer overflow, caused by improper bounds checking which could allow a local attacker to execute arbitrary code on the system with root privileges. IBM X-Force ID: 178960.

In the Linux kernel, the following vulnerability has been resolved: netdev: fix double-free in netdev_nl_bind_rx_doit() Sashiko flags that genlmsg_reply() always consumes the skb. The error path calls nlmsg_free(rsp) so we can't jump directly to it. Let's not unbind, just propagate the error to the user. This is the typical way of handling genlmsg_reply() failures. They shouldn't happen unless user does something silly like calling the kernel with an already-full rcvbuf.

IBM Security Guardium 10.6 and 11.2 could allow a local attacker to execute arbitrary commands on the system as an unprivileged user, caused by command injection vulnerability. IBM X-Force ID: 186700.

In the Linux kernel, the following vulnerability has been resolved: ipc: limit next_id allocation to the valid ID range The checkpoint/restore sysctl path can request the next SysV IPC id through ids->next_id. ipc_idr_alloc() currently forwards that request to idr_alloc() with an open-ended upper bound. If the valid tail of the SysV IPC id space is full, the allocation can spill beyond ipc_mni. The returned SysV IPC id still uses the normal index encoding, so later lookup and removal can target the wrong slot. This leaves the real IDR entry behind and breaks the IDR state for the object. The bug is in ipc_idr_alloc() in the checkpoint/restore path. 1. ids->next_id is passed to: idr_alloc(&ids->ipcs_idr, new, ipcid_to_idx(next_id), 0, ...) 2. The zero upper bound makes the allocation effectively open-ended. Once the valid SysV IPC tail is occupied, idr_alloc() can spill past ipc_mni and allocate an entry beyond the valid IPC id range. 3. The new object id is still encoded with the narrower SysV IPC index width: new->id = (new->seq << ipcmni_seq_shift()) + idx 4. Later removal goes through ipc_rmid(), which uses: ipcid_to_idx(ipcp->id) That truncates the real IDR index. An object actually stored at a high index can then be removed as if it lived at a low in-range index. 5. For shared memory, shm_destroy() frees the current object anyway, but the real high IDR slot is left behind as a dangling pointer. 6. A subsequent walk of /proc/sysvipc/shm reaches the stale IDR entry and dereferences freed memory. Prevent this by bounding the requested allocation to ipc_mni so the checkpoint/restore path fails once the valid range is exhausted.

In the Linux kernel, the following vulnerability has been resolved: drm/nouveau: avoid a use-after-free when BO init fails nouveau_bo_init() is backed by ttm_bo_init() and ferries its return code back to the caller. On failures, ttm_bo_init() invokes the provided destructor which should de-initialize and free the memory. Thus, when nouveau_bo_init() returns an error the gem object has already been released and the memory freed by nouveau_bo_del_ttm().

An issue was discovered in the Linux kernel before 5.7. The KVM subsystem allows out-of-range access to memslots after a deletion, aka CID-0774a964ef56. This affects arch/s390/kvm/kvm-s390.c, include/linux/kvm_host.h, and virt/kvm/kvm_main.c.

In the Linux kernel, the following vulnerability has been resolved: futex: Drop CLONE_THREAD requirement for private default hash alloc Currently need_futex_hash_allocate_default() depends on strict pthread semantics, abusing CLONE_THREAD. This breaks the non-concurrency assumptions when doing the mm->futex_ref pcpu allocations, leading to bugs[0] when sharing the mm in other ways; ie: BUG: KASAN: slab-use-after-free in futex_hash_put ... where the +1 bias can end up on a percpu counter that mm->futex_ref no longer points at. Loosen the check to cover any CLONE_VM clone, except vfork(). Excluding vfork keeps the existing paths untouched (no overhead), and we can't race in the first place: either the parent is suspended and the child runs alone, or mm->futex_ref is already allocated from an earlier CLONE_VM.

In the Linux kernel, the following vulnerability has been resolved: greybus: raw: fix use-after-free if write is called after disconnect If a user writes to the chardev after disconnect has been called, the kernel panics with the following trace (with CONFIG_INIT_ON_FREE_DEFAULT_ON=y): BUG: kernel NULL pointer dereference, address: 0000000000000218 ... Call Trace: <TASK> gb_operation_create_common+0x61/0x180 gb_operation_create_flags+0x28/0xa0 gb_operation_sync_timeout+0x6f/0x100 raw_write+0x7b/0xc7 [gb_raw] vfs_write+0xcf/0x420 ? task_mm_cid_work+0x136/0x220 ksys_write+0x63/0xe0 do_syscall_64+0xa4/0x290 entry_SYSCALL_64_after_hwframe+0x77/0x7f Disconnect calls gb_connection_destroy, which ends up freeing the connection object. When gb_operation_sync is called in the write file operations, its gets a freed connection as parameter and the kernel panics. The gb_connection_destroy cannot be moved out of the disconnect function, as the Greybus subsystem expect all connections belonging to a bundle to be destroyed when disconnect returns. To prevent this bug, use a rw lock to synchronize access between write and disconnect. This guarantees that the write function doesn't try to use a disconnected connection.

In the Linux kernel, the following vulnerability has been resolved: media: atomisp: Fix use after free in atomisp_alloc_css_stat_bufs() The "s3a_buf" is freed along with all the other items on the "asd->s3a_stats" list. It leads to a double free and a use after free.

In the Linux kernel, the following vulnerability has been resolved: net/sched: taprio: fix use-after-free in advance_sched() on schedule switch In advance_sched(), when should_change_schedules() returns true, switch_schedules() is called to promote the admin schedule to oper. switch_schedules() queues the old oper schedule for RCU freeing via call_rcu(), but 'next' still points into an entry of the old oper schedule. The subsequent 'next->end_time = end_time' and rcu_assign_pointer(q->current_entry, next) are use-after-free. Fix this by selecting 'next' from the new oper schedule immediately after switch_schedules(), and using its pre-calculated end_time. setup_first_end_time() sets the first entry's end_time to base_time + interval when the schedule is installed, so the value is already correct. The deleted 'end_time = sched_base_time(admin)' assignment was also harmful independently: it would overwrite the new first entry's pre-calculated end_time with just base_time.

arch/x86/kernel/entry_64.S in the Linux kernel before 3.17.5 does not properly handle faults associated with the Stack Segment (SS) segment register, which allows local users to gain privileges by triggering an IRET instruction that leads to access to a GS Base address from the wrong space.

In the Linux kernel, the following vulnerability has been resolved: wifi: nl80211: reject oversized EMA RNR lists nl80211_parse_rnr_elems() stores the parsed element count in a u8-backed cfg80211_rnr_elems::cnt field and uses that count to size the flexible array allocation. Reject nested NL80211_ATTR_EMA_RNR_ELEMS input once the count reaches 255, before incrementing it again. This keeps the parser aligned with the data structure it fills and matches the existing bound check used by nl80211_parse_mbssid_elems().