On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3.

An Improper Validation of Specified Type of Input vulnerability in Routing Protocol Daemon (RPD) of Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). If a BGP update is received over an established BGP session which contains a tunnel encapsulation attribute with a specifically malformed TLV, rpd will crash and restart. This issue affects: Junos OS: * all versions before 21.2R3-S7,  * from 21.3 before 21.3R3-S5,  * from 21.4 before 21.4R3-S5,  * from 22.1 before 22.1R3-S5,  * from 22.2 before 22.2R3-S3,  * from 22.3 before 22.3R3-S2,  * from 22.4 before 22.4R3,  * from 23.2 before 23.2R1-S2, 23.2R2. Junos OS Evolved: * all versions before 21.2R3-S7-EVO,  * from 21.3-EVO before 21.3R3-S5-EVO,  * from 21.4-EVO before 21.4R3-S5-EVO,  * from 22.2-EVO before 22.2R3-S3-EVO,  * from 22.3-EVO before 22.3R3-S2-EVO,  * from 22.4-EVO before 22.4R3-EVO,  * from 23.2-EVO before 23.2R1-S2-EVO, 23.2R2-EVO. This is a related but separate issue than the one described in JSA75739

An Improper Handling of Exceptional Conditions vulnerability in the broadband edge subscriber management daemon (bbe-smgd) of Juniper Networks Junos OS on MX Series allows an attacker directly connected to the vulnerable system who repeatedly flaps DHCP subscriber sessions to cause a slow memory leak, ultimately leading to a Denial of Service (DoS). Memory can only be recovered by manually restarting bbe-smgd. This issue only occurs if BFD liveness detection for DHCP subscribers is enabled. Systems without BFD liveness detection enabled are not vulnerable to this issue. Indication of the issue can be observed by periodically executing the 'show system processes extensive' command, which will indicate an increase in memory allocation for bbe-smgd. A small amount of memory is leaked every time a DHCP subscriber logs in, which will become visible over time, ultimately leading to memory starvation. user@junos> show system processes extensive | match bbe-smgd 13071 root 24 0 415M 201M select 0 0:41 7.28% bbe-smgd{bbe-smgd} 13071 root 20 0 415M 201M select 1 0:04 0.00% bbe-smgd{bbe-smgd} ... user@junos> show system processes extensive | match bbe-smgd 13071 root 20 0 420M 208M select 0 4:33 0.10% bbe-smgd{bbe-smgd} 13071 root 20 0 420M 208M select 0 0:12 0.00% bbe-smgd{bbe-smgd} ... This issue affects Juniper Networks Junos OS on MX Series: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.

An Improper Handling of Exceptional Conditions vulnerability in BGP session processing of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker, using specific timing outside the attacker's control, to flap BGP sessions and cause the routing protocol daemon (rpd) process to crash and restart, leading to a Denial of Service (DoS) condition. Continued BGP session flapping will create a sustained Denial of Service (DoS) condition. This issue only affects routers configured with non-stop routing (NSR) enabled. Graceful Restart (GR) helper mode, enabled by default, is also required for this issue to be exploitable. Note: NSR is not supported on the SRX Series and is therefore not affected by this vulnerability. When the BGP session flaps on the NSR-enabled router, the device enters GR-helper/LLGR-helper mode due to the peer having negotiated GR/LLGR-restarter capability and the backup BGP requests for replication of the GR/LLGR-helper session, master BGP schedules, and initiates replication of GR/LLGR stale routes to the backup BGP. In this state, if the BGP session with the BGP peer comes up again, unsolicited replication is initiated for the peer without cleaning up the ongoing GR/LLGR-helper mode replication. This parallel two instances of replication for the same peer leads to the assert if the BGP session flaps again. This issue affects: Juniper Networks Junos OS * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2. Juniper Networks Junos OS Evolved * All versions earlier than 21.3R3-S5-EVO; * 21.4 versions earlier than 21.4R3-S5-EVO; * 22.1 versions earlier than 22.1R3-S4-EVO; * 22.2 versions earlier than 22.2R3-S3-EVO; * 22.3 versions earlier than 22.3R3-S1-EVO; * 22.4 versions earlier than 22.4R2-S2-EVO, 22.4R3-EVO; * 23.2 versions earlier than 23.2R1-S1-EVO, 23.2R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in the Class of Service daemon (cosd) of Juniper Networks Junos OS allows an authenticated, network-based attacker with low privileges to cause a limited Denial of Service (DoS). In a scaled CoS scenario with 1000s of interfaces, when specific low privileged commands, received over NETCONF, SSH or telnet, are handled by cosd on behalf of mgd, the respective child management daemon (mgd) processes will get stuck. In case of (Netconf over) SSH this leads to stuck SSH sessions, so that when the connection-limit for SSH is reached, new sessions can't be established anymore. A similar behavior will be seen for telnet etc. Stuck mgd processes can be monitored by executing the following command:   user@host> show system processes extensive | match mgd | match sbwait This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2.

An Improper Check or Handling of Exceptional Conditions vulnerability in packet processing on the network interfaces of Juniper Networks Junos OS on JRR200 route reflector appliances allows an adjacent, network-based attacker sending a specific packet to the device to cause a kernel crash, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue can only be triggered by an attacker on the local broadcast domain. Packets routed to the device are unable to trigger this crash. This issue affects Juniper Networks Junos OS on JRR200: All versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S2, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2; 22.4 versions prior to 22.4R1-S1, 22.4R2.

An Improper Handling of Exceptional Conditions vulnerability in Berkeley Packet Filter (BPF) processing of Juniper Networks Junos OS allows an attacker, in rare cases, sending specific, unknown traffic patterns to cause the FPC and system to crash and restart. BPF provides a raw interface to data link layers in a protocol independent fashion. Internally within the Junos kernel, due to a rare timing issue (race condition), when a BPF instance is cloned, the newly created interface causes an internal structure leakage, leading to a system crash. The precise content and timing of the traffic patterns is indeterminate, but has been seen in a lab environment multiple times. This issue is more likely to occur when packet capturing is enabled.  See required configuration below. This issue affects Junos OS:  * all versions before 21.2R3-S9,  * from 21.4 before 21.4R3-S10,  * from 22.2 before 22.2R3-S6,  * from 22.4 before 22.4R3-S7,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S3,  * from 24.2 before 24.2R1-S1, 24.2R2.

An Improper Handling of Exceptional Conditions vulnerability in route processing of Juniper Networks Junos OS on specific end-of-life (EOL) ACX Series platforms allows an attacker to crash the Forwarding Engine Board (FEB) by flapping an interface, leading to a Denial of Service (DoS). On ACX1000, ACX1100, ACX2000, ACX2100, ACX2200, ACX4000, ACX5048, and ACX5096 devices, FEB0 will crash when the primary path port of the L2 circuit IGP (Interior Gateway Protocol) on the local device goes down. This issue is seen only when 'hot-standby' mode is configured for the L2 circuit. This issue affects Junos OS on ACX1000, ACX1100, ACX2000, ACX2100, ACX2200, ACX4000, ACX5048, and ACX5096:  * all versions before 21.2R3-S9.

On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash with a core dump if a specific DHCPv6 packet is received, resulting in a restart of the daemon. The daemon automatically restarts without intervention, but continued receipt and processing of these specific packets will repeatedly crash the JDHCPD process and sustain the Denial of Service (DoS) condition. This issue only affects DHCPv6. DHCPv4 is not affected by this issue. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1, 19.3R3-S2; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2.

A vulnerability in the processing of TCP MD5 authentication in Juniper Networks Junos OS Evolved may allow a BGP or LDP session configured with MD5 authentication to succeed, even if the peer does not have TCP MD5 authentication enabled. This could lead to untrusted or unauthorized sessions being established, resulting in an impact on confidentiality or stability of the network. This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.3R2-S1-EVO; 20.4 versions prior to 20.4R2-EVO; 21.1 versions prior to 21.1R2-EVO. Juniper Networks Junos OS is not affected by this issue.

On Juniper Networks Junos OS platforms configured as DHCPv6 local server or DHCPv6 Relay Agent, the Juniper Networks Dynamic Host Configuration Protocol Daemon (JDHCPD) process might crash if a malformed DHCPv6 packet is received, resulting in a restart of the daemon. The daemon automatically restarts without intervention, but continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects DHCPv6. DHCPv4 is not affected by this issue. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2.

Receipt of a specifically malformed NDP packet sent from the local area network (LAN) to a device running Juniper Networks Junos OS Evolved can cause the ndp process to crash, resulting in a Denial of Service (DoS). The process automatically restarts without intervention, but a continuous receipt of the malformed NDP packets could leaded to an extended Denial of Service condition. During this time, IPv6 neighbor learning will be affected. The issue occurs when parsing the incoming malformed NDP packet. Rather than simply discarding the packet, the process asserts, performing a controlled exit and restart, thereby avoiding any chance of an unhandled exception. Exploitation of this vulnerability is limited to a temporary denial of service, and cannot be leveraged to cause additional impact on the system. This issue is limited to the processing of IPv6 NDP packets. IPv4 packet processing cannot trigger, and is unaffected by this vulnerability. This issue affects all Juniper Networks Junos OS Evolved versions prior to 20.1R2-EVO. Junos OS is unaffected by this vulnerability.

Execution of the "show ospf interface extensive" or "show ospf interface detail" CLI commands on a Juniper Networks device running Junos OS may cause the routing protocols process (RPD) to crash and restart if OSPF interface authentication is configured, leading to a Denial of Service (DoS). By continuously executing the same CLI commands, a local attacker can repeatedly crash the RPD process causing a sustained Denial of Service. Note: Only systems utilizing ARM processors, found on the EX2300 and EX3400, are vulnerable to this issue. Systems shipped with other processor architectures are not vulnerable to this issue. The processor architecture can be displayed via the 'uname -a' command. For example: ARM (vulnerable): % uname -a | awk '{print $NF}' arm PowerPC (not vulnerable): % uname -a | awk '{print $NF}' powerpc AMD (not vulnerable): % uname -a | awk '{print $NF}' amd64 Intel (not vulnerable): % uname -a | awk '{print $NF}' i386 This issue affects Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D100; 14.1X53 versions prior to 14.1X53-D140, 14.1X53-D54; 15.1 versions prior to 15.1R7-S7; 15.1X49 versions prior to 15.1X49-D210; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S2, 18.3R2.

In a certain condition, receipt of a specific BGP UPDATE message might cause Juniper Networks Junos OS and Junos OS Evolved devices to advertise an invalid BGP UPDATE message to other peers, causing the other peers to terminate the established BGP session, creating a Denial of Service (DoS) condition. For example, Router A sends a specific BGP UPDATE to Router B, causing Router B to send an invalid BGP UPDATE message to Router C, resulting in termination of the BGP session between Router B and Router C. This issue might occur when there is at least a single BGP session established on the device that does not support 4 Byte AS extension (RFC 4893). Repeated receipt of the same BGP UPDATE can result in an extended DoS condition. This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R2-S11, 17.1R3-S2; 17.2 versions prior to 17.2R1-S9, 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D105, 17.2X75-D110, 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R2-S6, 18.2R3-S2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D51, 18.2X75-D60; 18.3 versions prior to 18.3R1-S6, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R3; 18.4 version 18.4R2 and later versions; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S2, 19.2R2. This issue does not affect Juniper Networks Junos OS prior to 16.1R1. This issue affects Juniper Networks Junos OS Evolved prior to 19.2R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a local, low-privileged attacker executing a CLI command to cause a Denial of Service (DoS). When asregex-optimized is configured and a specific "show route as-path" CLI command is executed, the rpd crashes and restarts. Repeated execution of this command will cause a sustained DoS condition. This issue affects Junos OS: * All versions before 21.2R3-S9, * from 21.4 before 21.4R3-S10, * from 22.2 before 22.2R3-S6, * from 22.4 before 22.4R3-S6, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S4, * from 24.2 before 24.2R2. and Junos OS Evolved: * All versions before 21.2R3-S9-EVO, * from 21.4-EVO before 21.4R3-S10-EVO, * from 22.2-EVO before 22.2R3-S6-EVO, * from 22.4-EVO before 22.4R3-S6-EVO, * from 23.2-EVO before 23.2R2-S3-EVO, * from 23.4-EVO before 23.4R2-S4-EVO, * from 24.2-EVO before 24.2R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker sending a specific BGP update packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continuous receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects iBGP and eBGP, and both IPv4 and IPv6 are affected by this vulnerability. This issue affects Junos OS:  * from 21.4 before 21.4R3-S9,  * from 22.2 before 22.2R3-S5,  * from 22.3 before 22.3R3-S4, * from 22.4 before 22.4R3-S5,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S3,  * from 24.2 before 24.2R1-S2, 24.2R2;  This issue does not affect versions prior to 21.1R1. Junos OS Evolved:  * from 21.4 before 21.4R3-S9-EVO,  * from 22.2 before 22.2R3-S5-EVO,  * from 22.3 before 22.3R3-S4-EVO, * from 22.4 before 22.4R3-S5-EVO,  * from 23.2 before 23.2R2-S3-EVO,  * from 23.4 before 23.4R2-S3-EVO,  * from 24.2 before 24.2R1-S2-EVO, 24.2R2-EVO. This issue does not affect versions prior to 21.1R1-EVO

An Improper Handling of Exceptional Conditions vulnerability in the command-line processing of Juniper Networks Junos OS on SRX1500, SRX4100, and SRX4200 devices allows a local, low-privileged authenticated attacker executing the 'show chassis environment pem' command to cause the chassis daemon (chassisd) to crash and restart, resulting in a temporary Denial of Service (DoS). However, repeated execution of this command will eventually cause the chassisd process to fail to restart, impacting packet processing on the system. This issue affects Junos OS on SRX1500, SRX4100, SRX4200:  * All versions before 21.4R3-S9,  * from 22.2 before 22.2R3-S5,  * from 22.3 before 22.3R3-S4,  * from 22.4 before 22.4R3-S4,  * from 23.2 before 23.2R2-S3,  * from 23.4 before 23.4R2-S1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in Juniper DHCP Daemon (jdhcpd) of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause the jdhcpd to consume all the CPU cycles resulting in a Denial of Service (DoS). On Junos OS devices with forward-snooped-client configured, if an attacker sends a specific DHCP packet to a non-configured interface, this will cause an infinite loop. The DHCP process will have to be restarted to recover the service. This issue affects: Juniper Networks Junos OS * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R2.

An Improper Handling of Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of the Juniper Networks Junos OS Evolved on ACX Series devices allows an unauthenticated, network based attacker sending specific transit protocol traffic to cause a partial Denial of Service (DoS) to downstream devices. Receipt of specific transit protocol packets is incorrectly processed by the Routing Engine (RE), filling up the DDoS protection queue which is shared between routing protocols. This influx of transit protocol packets causes DDoS protection violations, resulting in protocol flaps which can affect connectivity to networking devices. This issue affects both IPv4 and IPv6. This issue does not require any specific routing protocol to be configured or enabled. The following commands can be used to monitor the DDoS protection queue:        labuser@re0> show evo-pfemand host pkt-stats     labuser@re0> show host-path ddos all-policers This issue affects Junos OS Evolved:  * All versions before 21.4R3-S8-EVO,  * from 22.2 before 22.2R3-S4-EVO,  * from 22.3 before 22.3R3-S4-EVO,  * from 22.4 before 22.4R3-S3-EVO,  * from 23.2 before 23.2R2-EVO,  * from 23.4 before 23.4R1-S1-EVO, 23.4R2-EVO,  * from 24.2 before 24.2R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause Denial of Service (DoS). When a BGP UPDATE with malformed path attribute is received over an established BGP session, rpd crashes and restarts. Continuous receipt of a BGP UPDATE with a specifically malformed path attribute will create a sustained Denial of Service (DoS) condition for impacted devices. While this issue affects systems running 32-bit and 64-bit systems, the probability of impact on 64-bit system is extremely low.  According to KB25803 https://supportportal.juniper.net/s/article/Junos-How-to-check-if-Junos-OS-is-64-or-32-bit-on-a-router , customers can confirm 32-bit or 64-bit system via the ' show version detail ' command:      lab@router> show version detail| match 32      JUNOS 32-bit kernel Software Suite       lab@router> show version detail| match 64      JUNOS 64-bit kernel Software Suite  This issue affects:  Juniper Networks Junos OS:  * All versions before 21.4R3-S8,  * from 22.2 before 22.2R3-S4,  * from 22.4 before 22.4R3-S3,  * from 23.2 before 23.2R2-S1,  * from 23.4 before 23.4R1-S2, 23.4R2.  Juniper Networks Junos OS Evolved:  * All versions before 21.4R3-S8-EVO, * from 22.2 before 22.2R3-S4-EVO, * from 22.4 before 22.4R3-S3-EVO, * from 23.2 before 23.2R2-S1-EVO, * from 23.4 before 23.4R1-S2-EVO, 23.4R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). When conflicting information (IP or ISO addresses) about a node is added to the Traffic Engineering (TE) database and then a subsequent operation attempts to process these, rpd will crash and restart. This issue affects: Junos OS: * 22.4 versions before 22.4R3-S1, * 23.2 versions before 23.2R2,  * 23.4 versions before 23.4R1-S1, 23.4R2,  This issue does not affect Junos OS versions earlier than 22.4R1. Junos OS Evolved: * 22.4-EVO versions before 22.4R3-S2-EVO, * 23.2-EVO versions before 23.2R2-EVO, * 23.4-EVO versions before 23.4R1-S1-EVO, 23.4R2-EVO, This issue does not affect Junos OS Evolved versions earlier than before 22.4R1.

An Improper Handling of Exceptional Conditions vulnerability on specific PTX Series devices, including the PTX1000, PTX3000 (NextGen), PTX5000, PTX10002-60C, PTX10008, and PTX10016 Series, in Juniper Networks Junos OS allows an unauthenticated MPLS-based attacker to cause a Denial of Service (DoS) by triggering the dcpfe process to crash and FPC to restart. On affected PTX Series devices, processing specific MPLS packets received on an interface with multiple units configured may cause FPC to restart unexpectedly. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects PTX Series devices utilizing specific FPCs found on PTX1000, PTX3000 (NextGen), PTX5000, PTX10002-60C, PTX10008, and PTX10016 Series devices, only if multiple units are configured on the ingress interface, and at least one unit has 'family mpls' *not* configured. See the configuration sample below for more information. No other platforms are affected by this vulnerability. This issue affects: Juniper Networks Junos OS on PTX Series: All versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability combined with Improper Handling of Exceptional Conditions in Juniper Networks Junos OS on QFX Series and PTX Series allows an unauthenticated network based attacker to cause increased FPC CPU utilization by sending specific IP packets which are being VXLAN encapsulated leading to a partial Denial of Service (DoS). Continued receipted of these specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX Series: All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS on PTX Series: All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.

An Improper Handling of Exceptional Conditions vulnerability in Juniper Networks Junos OS and Junos OS Evolved allows an adjacent unauthenticated attacker to cause a Denial of Service (DoS), which causes the l2cpd process to crash by sending a specific TLV. The l2cpd process is responsible for layer 2 control protocols, such as STP, RSTP, MSTP, VSTP, ERP, and LLDP.  The impact of the l2cpd crash is reinitialization of STP protocols (RSTP, MSTP or VSTP), and MVRP and ERP, leading to a Denial of Service.  Continued receipt and processing of this specific TLV will create a sustained Denial of Service (DoS) condition. This issue affects: Junos OS: all versions before 20.4R3-S9, from 21.2 before 21.2R3-S7, from 21.3 before 21.3R3-S5, from 21.4 before 21.4R3-S4, from 22.1 before 22.1R3-S4, from 22.2 before 22.2R3-S2, from 22.3 before 22.3R2-S2, 22.3R3-S1, from 22.4 before 22.4R2-S2, 22.4R3, from 23.2 before 23.2R1-S1, 23.2R2; Junos OS Evolved: all versions before 21.2R3-S7, from 21.3 before 21.3R3-S5-EVO, from 21.4 before 21.4R3-S5-EVO, from 22.1 before 22.1R3-S4-EVO, from 22.2 before 22.2R3-S2-EVO, from 22.3 before 22.3R2-S2-EVO, 22.3R3-S1-EVO, from 22.4 before 22.4R2-S2-EVO, 22.4R3-EVO, from 23.2 before 23.2R1-S1-EVO, 23.2R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in packet processing of Juniper Networks Junos OS on MX Series with MPC10/MPC11/LC9600 line cards, EX9200 with EX9200-15C lines cards, MX304 devices, and Juniper Networks Junos OS Evolved on PTX Series, allows an attacker sending malformed DHCP packets to cause ingress packet processing to stop, leading to a Denial of Service (DoS).  Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue only occurs if DHCP snooping is enabled. See configuration below. This issue can be detected using following commands. Their output will display the interface status going down: user@device>show interfaces <if--x/x/x> user@device>show log messages | match <if--x/x/x> user@device>show log messages ==> will display the "[Error] Wedge-Detect : Host Loopback Wedge Detected: PFE: no," logs. This issue affects: Junos OS on MX Series with MPC10/MPC11/LC9600 line cards, EX9200 with EX9200-15C line cards, and MX304: * All versions before 21.2R3-S7, * from 21.4 before 21.4R3-S6, * from 22.2 before 22.2R3-S3, * all versions of 22.3, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2; Junos OS Evolved on PTX Series: * from 19.3R1-EVO before 21.2R3-S8-EVO, * from 21.4-EVO before 21.4R3-S7-EVO, * from 22.1-EVO before 22.1R3-S6-EVO, * from 22.2-EVO before 22.2R3-S5-EVO, * from 22.3-EVO before 22.3R3-S3-EVO, * from 22.4-EVO before 22.4R3-S1-EVO, * from 23.2-EVO before 23.2R2-S2-EVO, * from 23.4-EVO before 23.4R2-EVO. Junos OS Evolved releases prior to 19.3R1-EVO are unaffected by this vulnerability

An Improper Handling of Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a logically adjacent downstream RSVP neighbor to cause kernel memory exhaustion, leading to a kernel crash, resulting in a Denial of Service (DoS). The kernel memory leak and eventual crash will be seen when the downstream RSVP neighbor has a persistent error which will not be corrected. System kernel memory can be monitored through the use of the 'show system kernel memory' command as shown below: user@router> show system kernel memory   Real memory total/reserved: 4130268/ 133344 Kbytes kmem map free: 18014398509110220 Kbytes This issue affects: Junos OS: * All versions before 20.4R3-S9, * All versions of 21.2, * from 21.4 before 21.4R3-S5, * from 22.1 before 22.1R3-S5, * from 22.2 before 22.2R3-S3, * from 22.3 before 22.3R3-S2, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2; Junos OS Evolved: * All versions before 21.4R3-S5-EVO, * from 22.1-EVO before 22.1R3-S5-EVO, * from 22.2-EVO before 22.2R3-S3-EVO, * from 22.3-EVO before 22.3R3-S2-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.

Improper Handling of Exceptional Conditions in Ethernet interface frame processing of Juniper Networks Junos OS allows an attacker to send specially crafted frames over the local Ethernet segment, causing the interface to go into a down state, resulting in a Denial of Service (DoS) condition. The interface does not recover on its own and the FPC must be reset manually. Continued receipt and processing of these frames will create a sustained Denial of Service (DoS) condition. This issue is platform-specific and affects the following platforms and line cards: * MPC7E/8E/9E and MPC10E on MX240, MX480, MX960, MX2008, MX2010, and MX2020 * MX204, MX10003, MX10008, MX10016 * EX9200, EX9251 * SRX4600 No other products or platforms are affected by this vulnerability. An indication of this issue occurring can be seen in the system log messages, as shown below: user@host> show log messages | match "Failed to complete DFE tuning" fpc4 smic_phy_dfe_tuning_state: et-4/1/6 - Failed to complete DFE tuning (count 3) and interface will be in a permanently down state: user@host> show interfaces et-4/1/6 terse Interface Admin Link Proto Local Remote et-4/1/6 up down et-4/1/6.0 up down aenet --> ae101.0 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S7 on MX Series; 17.1R1 and later versions prior to 17.2R3-S3 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S11, 17.4R3-S1 on MX Series, SRX4600; 18.1 versions prior to 18.1R3-S10 on MX Series, EX9200 Series, SRX4600; 18.2 versions prior to 18.2R3-S3 on MX Series, EX9200 Series, SRX4600; 18.3 versions prior to 18.3R3-S1 on MX Series, EX9200 Series, SRX4600; 18.4 versions prior to 18.4R2-S3, 18.4R3 on MX Series, EX9200 Series, SRX4600; 19.1 versions prior to 19.1R2-S1, 19.1R3 on MX Series, EX9200 Series, SRX4600; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series, EX9200 Series, SRX4600; 19.3 versions prior to 19.3R2 on MX Series, EX9200 Series, SRX4600. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.

Due to a vulnerability in DDoS protection in Juniper Networks Junos OS and Junos OS Evolved on QFX5K Series switches in a VXLAN configuration, instability might be experienced in the underlay network as a consequence of exceeding the default ddos-protection aggregate threshold. If an attacker on a client device on the overlay network sends a high volume of specific, legitimate traffic in the overlay network, due to an improperly detected DDoS violation, the leaf might not process certain L2 traffic, sent by spines in the underlay network. Continued receipt and processing of the high volume traffic will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX5K Series: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S2, 20.3R2. Juniper Networks Junos OS Evolved on QFX5220: All versions prior to 20.3R2-EVO.

Unbound before 1.9.4 accesses uninitialized memory, which allows remote attackers to trigger a crash via a crafted NOTIFY query. The source IP address of the query must match an access-control rule.

An issue was discovered in Open Network Operating System (ONOS) 1.14. In the Ethernet VPN application (org.onosproject.evpnopenflow), the host event listener does not handle the following event types: HOST_MOVED, HOST_UPDATED. In combination with other applications, this could lead to the absence of intended code execution.

The adapter @hono/node-server allows you to run your Hono application on Node.js. Prior to 1.10.1, the application hangs when receiving a Host header with a value that `@hono/node-server` can't handle well. Invalid values are those that cannot be parsed by the `URL` as a hostname such as an empty string, slashes `/`, and other strings. The version 1.10.1 includes the fix for this issue.

All versions of the CODESYS V3 Runtime Toolkit for VxWorks from version V3.5.8.0 and before version V3.5.17.10 have Improper Handling of Exceptional Conditions.

In Mitsubishi Electric MELSEC-Q series Ethernet module QJ71E71-100 serial number 20121 and prior, an attacker could send crafted TCP packets against the FTP service, forcing the target devices to enter an error mode and cause a denial-of-service condition.

In Progress MOVEit Transfer before 2021.0.9 (13.0.9), 2021.1.7 (13.1.7), 2022.0.7 (14.0.7), 2022.1.8 (14.1.8), and 2023.0.4 (15.0.4), it is possible for an attacker to invoke a method that results in an unhandled exception. Triggering this workflow can cause the MOVEit Transfer application to terminate unexpectedly.

Unhandled exception in Intel(R) Baseboard Management Controller firmware may allow an unauthenticated user to potentially enable denial of service via network access.

In wlan firmware, there is possible system crash due to an uncaught exception. This could lead to remote denial of service with no additional execution privileges needed. User interaction is not needed for exploitation. Patch ID: ALPS07664720; Issue ID: ALPS07664720.

Improper handling of exceptional conditions in SuiteLink server while processing command 0x01

A vulnerability in Apache Tomcat allows an attacker to remotely trigger a denial of service. An error introduced as part of a change to improve error handling during non-blocking I/O meant that the error flag associated with the Request object was not reset between requests. This meant that once a non-blocking I/O error occurred, all future requests handled by that request object would fail. Users were able to trigger non-blocking I/O errors, e.g. by dropping a connection, thereby creating the possibility of triggering a DoS. Applications that do not use non-blocking I/O are not exposed to this vulnerability. This issue affects Apache Tomcat 10.0.3 to 10.0.4; 9.0.44; 8.5.64.

Traefik is an HTTP reverse proxy and load balancer. In affected versions sending a GET request to any Traefik endpoint with the "Content-length" request header results in an indefinite hang with the default configuration. This vulnerability can be exploited by attackers to induce a denial of service. This vulnerability has been addressed in version 2.11.2 and 3.0.0-rc5. Users are advised to upgrade. For affected versions, this vulnerability can be mitigated by configuring the readTimeout option.

In Eclipse Jetty 7.2.2 to 9.4.38, 10.0.0.alpha0 to 10.0.1, and 11.0.0.alpha0 to 11.0.1, CPU usage can reach 100% upon receiving a large invalid TLS frame.

decompress_gunzip.c in BusyBox through 1.32.1 mishandles the error bit on the huft_build result pointer, with a resultant invalid free or segmentation fault, via malformed gzip data.

Envoy is a high-performance edge/middle/service proxy. Envoy crashes in Proxy protocol when using an address type that isn’t supported by the OS. Envoy is susceptible to crashing on a host with IPv6 disabled and a listener config with proxy protocol enabled when it receives a request where the client presents its IPv6 address. It is valid for a client to present its IPv6 address to a target server even though the whole chain is connected via IPv4. This issue has been addressed in released 1.29.1, 1.28.1, 1.27.3, and 1.26.7. Users are advised to upgrade. There are no known workarounds for this vulnerability.

A vulnerability has been identified in SIMATIC HMI Comfort Outdoor Panels V15 7\" & 15\" (incl. SIPLUS variants) (All versions < V15.1 Update 6), SIMATIC HMI Comfort Outdoor Panels V16 7\" & 15\" (incl. SIPLUS variants) (All versions < V16 Update 4), SIMATIC HMI Comfort Panels V15 4\" - 22\" (incl. SIPLUS variants) (All versions < V15.1 Update 6), SIMATIC HMI Comfort Panels V16 4\" - 22\" (incl. SIPLUS variants) (All versions < V16 Update 4), SIMATIC HMI KTP Mobile Panels V15 KTP400F, KTP700, KTP700F, KTP900 and KTP900F (All versions < V15.1 Update 6), SIMATIC HMI KTP Mobile Panels V16 KTP400F, KTP700, KTP700F, KTP900 and KTP900F (All versions < V16 Update 4), SIMATIC WinCC Runtime Advanced V15 (All versions < V15.1 Update 6), SIMATIC WinCC Runtime Advanced V16 (All versions < V16 Update 4). SmartVNC client fails to handle an exception properly if the program execution process is modified after sending a packet from the server, which could result in a Denial-of-Service condition.