In the Linux kernel, the following vulnerability has been resolved: can: mcp251xfd: fix infinite loop when xmit fails When the mcp251xfd_start_xmit() function fails, the driver stops processing messages, and the interrupt routine does not return, running indefinitely even after killing the running application. Error messages: [ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16 [ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3). ... and repeat forever. The issue can be triggered when multiple devices share the same SPI interface. And there is concurrent access to the bus. The problem occurs because tx_ring->head increments even if mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX package while still expecting a response in mcp251xfd_handle_tefif_one(). Resolve the issue by starting a workqueue to write the tx obj synchronously if err = -EBUSY. In case of another error, decrement tx_ring->head, remove skb from the echo stack, and drop the message. [mkl: use more imperative wording in patch description]

A potential stack overflow via infinite loop issue was found in various NIC emulators of QEMU in versions up to and including 5.2.0. The issue occurs in loopback mode of a NIC wherein reentrant DMA checks get bypassed. A guest user/process may use this flaw to consume CPU cycles or crash the QEMU process on the host resulting in DoS scenario.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: Avoid infinite loop trying to resize local TT If the MTU of one of an attached interface becomes too small to transmit the local translation table then it must be resized to fit inside all fragments (when enabled) or a single packet. But if the MTU becomes too low to transmit even the header + the VLAN specific part then the resizing of the local TT will never succeed. This can for example happen when the usable space is 110 bytes and 11 VLANs are on top of batman-adv. In this case, at least 116 byte would be needed. There will just be an endless spam of batman_adv: batadv0: Forced to purge local tt entries to fit new maximum fragment MTU (110) in the log but the function will never finish. Problem here is that the timeout will be halved all the time and will then stagnate at 0 and therefore never be able to reduce the table even more. There are other scenarios possible with a similar result. The number of BATADV_TT_CLIENT_NOPURGE entries in the local TT can for example be too high to fit inside a packet. Such a scenario can therefore happen also with only a single VLAN + 7 non-purgable addresses - requiring at least 120 bytes. While this should be handled proactively when: * interface with too low MTU is added * VLAN is added * non-purgeable local mac is added * MTU of an attached interface is reduced * fragmentation setting gets disabled (which most likely requires dropping attached interfaces) not all of these scenarios can be prevented because batman-adv is only consuming events without the the possibility to prevent these actions (non-purgable MAC address added, MTU of an attached interface is reduced). It is therefore necessary to also make sure that the code is able to handle also the situations when there were already incompatible system configuration are present.

In the Linux kernel, the following vulnerability has been resolved: crypto: qcom-rng - fix infinite loop on requests not multiple of WORD_SZ The commit referenced in the Fixes tag removed the 'break' from the else branch in qcom_rng_read(), causing an infinite loop whenever 'max' is not a multiple of WORD_SZ. This can be reproduced e.g. by running: kcapi-rng -b 67 >/dev/null There are many ways to fix this without adding back the 'break', but they all seem more awkward than simply adding it back, so do just that. Tested on a machine with Qualcomm Amberwing processor.

ImageMagick 6.7.5-7 and earlier allows remote attackers to cause a denial of service (infinite loop and hang) via a crafted image whose IFD contains IOP tags that all reference the beginning of the IDF.

In the Linux kernel, the following vulnerability has been resolved: f2fs: avoid infinite loop to flush node pages xfstests/generic/475 can give EIO all the time which give an infinite loop to flush node page like below. Let's avoid it. [16418.518551] Call Trace: [16418.518553] ? dm_submit_bio+0x48/0x400 [16418.518574] ? submit_bio_checks+0x1ac/0x5a0 [16418.525207] __submit_bio+0x1a9/0x230 [16418.525210] ? kmem_cache_alloc+0x29e/0x3c0 [16418.525223] submit_bio_noacct+0xa8/0x2b0 [16418.525226] submit_bio+0x4d/0x130 [16418.525238] __submit_bio+0x49/0x310 [f2fs] [16418.525339] ? bio_add_page+0x6a/0x90 [16418.525344] f2fs_submit_page_bio+0x134/0x1f0 [f2fs] [16418.525365] read_node_page+0x125/0x1b0 [f2fs] [16418.525388] __get_node_page.part.0+0x58/0x3f0 [f2fs] [16418.525409] __get_node_page+0x2f/0x60 [f2fs] [16418.525431] f2fs_get_dnode_of_data+0x423/0x860 [f2fs] [16418.525452] ? asm_sysvec_apic_timer_interrupt+0x12/0x20 [16418.525458] ? __mod_memcg_state.part.0+0x2a/0x30 [16418.525465] ? __mod_memcg_lruvec_state+0x27/0x40 [16418.525467] ? __xa_set_mark+0x57/0x70 [16418.525472] f2fs_do_write_data_page+0x10e/0x7b0 [f2fs] [16418.525493] f2fs_write_single_data_page+0x555/0x830 [f2fs] [16418.525514] ? sysvec_apic_timer_interrupt+0x4e/0x90 [16418.525518] ? asm_sysvec_apic_timer_interrupt+0x12/0x20 [16418.525523] f2fs_write_cache_pages+0x303/0x880 [f2fs] [16418.525545] ? blk_flush_plug_list+0x47/0x100 [16418.525548] f2fs_write_data_pages+0xfd/0x320 [f2fs] [16418.525569] do_writepages+0xd5/0x210 [16418.525648] filemap_fdatawrite_wbc+0x7d/0xc0 [16418.525655] filemap_fdatawrite+0x50/0x70 [16418.525658] f2fs_sync_dirty_inodes+0xa4/0x230 [f2fs] [16418.525679] f2fs_write_checkpoint+0x16d/0x1720 [f2fs] [16418.525699] ? ttwu_do_wakeup+0x1c/0x160 [16418.525709] ? ttwu_do_activate+0x6d/0xd0 [16418.525711] ? __wait_for_common+0x11d/0x150 [16418.525715] kill_f2fs_super+0xca/0x100 [f2fs] [16418.525733] deactivate_locked_super+0x3b/0xb0 [16418.525739] deactivate_super+0x40/0x50 [16418.525741] cleanup_mnt+0x139/0x190 [16418.525747] __cleanup_mnt+0x12/0x20 [16418.525749] task_work_run+0x6d/0xa0 [16418.525765] exit_to_user_mode_prepare+0x1ad/0x1b0 [16418.525771] syscall_exit_to_user_mode+0x27/0x50 [16418.525774] do_syscall_64+0x48/0xc0 [16418.525776] entry_SYSCALL_64_after_hwframe+0x44/0xae

The Linux kernel before 2.6.37 does not properly implement a certain clock-update optimization, which allows local users to cause a denial of service (system hang) via an application that executes code in a loop.

The inet_diag_bc_audit function in net/ipv4/inet_diag.c in the Linux kernel before 2.6.39.3 does not properly audit INET_DIAG bytecode, which allows local users to cause a denial of service (kernel infinite loop) via crafted INET_DIAG_REQ_BYTECODE instructions in a netlink message, as demonstrated by an INET_DIAG_BC_JMP instruction with a zero yes value, a different vulnerability than CVE-2010-3880.

A flaw was found in the Linux kernel in the function hid_debug_events_read() in drivers/hid/hid-debug.c file which may enter an infinite loop with certain parameters passed from a userspace. A local privileged user ("root") can cause a system lock up and a denial of service. Versions from v4.18 and newer are vulnerable.

avahi-core/socket.c in avahi-daemon in Avahi before 0.6.29 allows remote attackers to cause a denial of service (infinite loop) via an empty mDNS (1) IPv4 or (2) IPv6 UDP packet to port 5353. NOTE: this vulnerability exists because of an incorrect fix for CVE-2010-2244.

A locally locally exploitable DOS vulnerability was found in pax-linux versions 2.6.32.33-test79.patch, 2.6.38-test3.patch, and 2.6.37.4-test14.patch. A bad bounds check in arch_get_unmapped_area_topdown triggered by programs doing an mmap after a MAP_GROWSDOWN mmap will create an infinite loop condition without releasing the VM semaphore eventually leading to a system crash.

net/ipv4/inet_diag.c in the Linux kernel before 2.6.37-rc2 does not properly audit INET_DIAG bytecode, which allows local users to cause a denial of service (kernel infinite loop) via crafted INET_DIAG_REQ_BYTECODE instructions in a netlink message that contains multiple attribute elements, as demonstrated by INET_DIAG_BC_JMP instructions.

In the Linux kernel, the following vulnerability has been resolved: af_unix: Fix task hung while purging oob_skb in GC. syzbot reported a task hung; at the same time, GC was looping infinitely in list_for_each_entry_safe() for OOB skb. [0] syzbot demonstrated that the list_for_each_entry_safe() was not actually safe in this case. A single skb could have references for multiple sockets. If we free such a skb in the list_for_each_entry_safe(), the current and next sockets could be unlinked in a single iteration. unix_notinflight() uses list_del_init() to unlink the socket, so the prefetched next socket forms a loop itself and list_for_each_entry_safe() never stops. Here, we must use while() and make sure we always fetch the first socket. [0]: Sending NMI from CPU 0 to CPUs 1: NMI backtrace for cpu 1 CPU: 1 PID: 5065 Comm: syz-executor236 Not tainted 6.8.0-rc3-syzkaller-00136-g1f719a2f3fa6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024 RIP: 0010:preempt_count arch/x86/include/asm/preempt.h:26 [inline] RIP: 0010:check_kcov_mode kernel/kcov.c:173 [inline] RIP: 0010:__sanitizer_cov_trace_pc+0xd/0x60 kernel/kcov.c:207 Code: cc cc cc cc 66 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 65 48 8b 14 25 40 c2 03 00 <65> 8b 05 b4 7c 78 7e a9 00 01 ff 00 48 8b 34 24 74 0f f6 c4 01 74 RSP: 0018:ffffc900033efa58 EFLAGS: 00000283 RAX: ffff88807b077800 RBX: ffff88807b077800 RCX: 1ffffffff27b1189 RDX: ffff88802a5a3b80 RSI: ffffffff8968488d RDI: ffff88807b077f70 RBP: ffffc900033efbb0 R08: 0000000000000001 R09: fffffbfff27a900c R10: ffffffff93d48067 R11: ffffffff8ae000eb R12: ffff88807b077800 R13: dffffc0000000000 R14: ffff88807b077e40 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000564f4fc1e3a8 CR3: 000000000d57a000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <NMI> </NMI> <TASK> unix_gc+0x563/0x13b0 net/unix/garbage.c:319 unix_release_sock+0xa93/0xf80 net/unix/af_unix.c:683 unix_release+0x91/0xf0 net/unix/af_unix.c:1064 __sock_release+0xb0/0x270 net/socket.c:659 sock_close+0x1c/0x30 net/socket.c:1421 __fput+0x270/0xb80 fs/file_table.c:376 task_work_run+0x14f/0x250 kernel/task_work.c:180 exit_task_work include/linux/task_work.h:38 [inline] do_exit+0xa8a/0x2ad0 kernel/exit.c:871 do_group_exit+0xd4/0x2a0 kernel/exit.c:1020 __do_sys_exit_group kernel/exit.c:1031 [inline] __se_sys_exit_group kernel/exit.c:1029 [inline] __x64_sys_exit_group+0x3e/0x50 kernel/exit.c:1029 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd5/0x270 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x6f/0x77 RIP: 0033:0x7f9d6cbdac09 Code: Unable to access opcode bytes at 0x7f9d6cbdabdf. RSP: 002b:00007fff5952feb8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f9d6cbdac09 RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000000 RBP: 00007f9d6cc552b0 R08: ffffffffffffffb8 R09: 0000000000000006 R10: 0000000000000006 R11: 0000000000000246 R12: 00007f9d6cc552b0 R13: 0000000000000000 R14: 00007f9d6cc55d00 R15: 00007f9d6cbabe70 </TASK>

In the Linux kernel, the following vulnerability has been resolved: x86/fpu: Stop relying on userspace for info to fault in xsave buffer Before this change, the expected size of the user space buffer was taken from fx_sw->xstate_size. fx_sw->xstate_size can be changed from user-space, so it is possible construct a sigreturn frame where: * fx_sw->xstate_size is smaller than the size required by valid bits in fx_sw->xfeatures. * user-space unmaps parts of the sigrame fpu buffer so that not all of the buffer required by xrstor is accessible. In this case, xrstor tries to restore and accesses the unmapped area which results in a fault. But fault_in_readable succeeds because buf + fx_sw->xstate_size is within the still mapped area, so it goes back and tries xrstor again. It will spin in this loop forever. Instead, fault in the maximum size which can be touched by XRSTOR (taken from fpstate->user_size). [ dhansen: tweak subject / changelog ]

An infinite loop issue was found in the vhost_net kernel module in Linux Kernel up to and including v5.1-rc6, while handling incoming packets in handle_rx(). It could occur if one end sends packets faster than the other end can process them. A guest user, maybe remote one, could use this flaw to stall the vhost_net kernel thread, resulting in a DoS scenario.

An infinite loop in SMLLexer in Pygments versions 1.5 to 2.7.3 may lead to denial of service when performing syntax highlighting of a Standard ML (SML) source file, as demonstrated by input that only contains the "exception" keyword.

An infinite loop flaw was found in the e1000 NIC emulator of the QEMU. This issue occurs while processing transmits (tx) descriptors in process_tx_desc if various descriptor fields are initialized with invalid values. This flaw allows a guest to consume CPU cycles on the host, resulting in a denial of service. The highest threat from this vulnerability is to system availability.

A vulnerability was found in libX11 due to an infinite loop within the PutSubImage() function. This flaw allows a local user to consume all available system resources and cause a denial of service condition.

Certain WithSecure products allow Denial of Service (infinite loop). This affects WithSecure Client Security 15, WithSecure Server Security 15, WithSecure Email and Server Security 15, WithSecure Elements Endpoint Protection 17 and later, WithSecure Client Security for Mac 15, WithSecure Elements Endpoint Protection for Mac 17 and later, Linux Security 64 12.0 , Linux Protection 12.0, and WithSecure Atlant (formerly F-Secure Atlant) 1.0.35-1.

Certain WithSecure products allow an infinite loop in a scanning engine via unspecified file types. This affects WithSecure Client Security 15, WithSecure Server Security 15, WithSecure Email and Server Security 15, WithSecure Elements Endpoint Protection 17 and later, WithSecure Client Security for Mac 15, WithSecure Elements Endpoint Protection for Mac 17 and later, Linux Security 64 12.0 , Linux Protection 12.0, and WithSecure Atlant (formerly F-Secure Atlant) 1.0.35-1.

Certain WithSecure products allow an infinite loop in a scanning engine via unspecified file types. This affects WithSecure Client Security 15, WithSecure Server Security 15, WithSecure Email and Server Security 15, WithSecure Elements Endpoint Protection 17 and later, WithSecure Client Security for Mac 15, WithSecure Elements Endpoint Protection for Mac 17 and later, Linux Security 64 12.0 , Linux Protection 12.0, and WithSecure Atlant (formerly F-Secure Atlant) 1.0.35-1.

In the Linux kernel, the following vulnerability has been resolved: net/sched: act_api: fix possible infinite loop in tcf_idr_check_alloc() syzbot found hanging tasks waiting on rtnl_lock [1] A reproducer is available in the syzbot bug. When a request to add multiple actions with the same index is sent, the second request will block forever on the first request. This holds rtnl_lock, and causes tasks to hang. Return -EAGAIN to prevent infinite looping, while keeping documented behavior. [1] INFO: task kworker/1:0:5088 blocked for more than 143 seconds. Not tainted 6.9.0-rc4-syzkaller-00173-g3cdb45594619 #0 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/1:0 state:D stack:23744 pid:5088 tgid:5088 ppid:2 flags:0x00004000 Workqueue: events_power_efficient reg_check_chans_work Call Trace: <TASK> context_switch kernel/sched/core.c:5409 [inline] __schedule+0xf15/0x5d00 kernel/sched/core.c:6746 __schedule_loop kernel/sched/core.c:6823 [inline] schedule+0xe7/0x350 kernel/sched/core.c:6838 schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:6895 __mutex_lock_common kernel/locking/mutex.c:684 [inline] __mutex_lock+0x5b8/0x9c0 kernel/locking/mutex.c:752 wiphy_lock include/net/cfg80211.h:5953 [inline] reg_leave_invalid_chans net/wireless/reg.c:2466 [inline] reg_check_chans_work+0x10a/0x10e0 net/wireless/reg.c:2481

In the Linux kernel, the following vulnerability has been resolved: openvswitch: fix lockup on tx to unregistering netdev with carrier Commit in a fixes tag attempted to fix the issue in the following sequence of calls: do_output -> ovs_vport_send -> dev_queue_xmit -> __dev_queue_xmit -> netdev_core_pick_tx -> skb_tx_hash When device is unregistering, the 'dev->real_num_tx_queues' goes to zero and the 'while (unlikely(hash >= qcount))' loop inside the 'skb_tx_hash' becomes infinite, locking up the core forever. But unfortunately, checking just the carrier status is not enough to fix the issue, because some devices may still be in unregistering state while reporting carrier status OK. One example of such device is a net/dummy. It sets carrier ON on start, but it doesn't implement .ndo_stop to set the carrier off. And it makes sense, because dummy doesn't really have a carrier. Therefore, while this device is unregistering, it's still easy to hit the infinite loop in the skb_tx_hash() from the OVS datapath. There might be other drivers that do the same, but dummy by itself is important for the OVS ecosystem, because it is frequently used as a packet sink for tcpdump while debugging OVS deployments. And when the issue is hit, the only way to recover is to reboot. Fix that by also checking if the device is running. The running state is handled by the net core during unregistering, so it covers unregistering case better, and we don't really need to send packets to devices that are not running anyway. While only checking the running state might be enough, the carrier check is preserved. The running and the carrier states seem disjoined throughout the code and different drivers. And other core functions like __dev_direct_xmit() check both before attempting to transmit a packet. So, it seems safer to check both flags in OVS as well.

An issue was discovered in the Linux kernel before 5.0.4. The 9p filesystem did not protect i_size_write() properly, which causes an i_size_read() infinite loop and denial of service on SMP systems.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath11k: fix RCU stall while reaping monitor destination ring While processing the monitor destination ring, MSDUs are reaped from the link descriptor based on the corresponding buf_id. However, sometimes the driver cannot obtain a valid buffer corresponding to the buf_id received from the hardware. This causes an infinite loop in the destination processing, resulting in a kernel crash. kernel log: ath11k_pci 0000:58:00.0: data msdu_pop: invalid buf_id 309 ath11k_pci 0000:58:00.0: data dp_rx_monitor_link_desc_return failed ath11k_pci 0000:58:00.0: data msdu_pop: invalid buf_id 309 ath11k_pci 0000:58:00.0: data dp_rx_monitor_link_desc_return failed Fix this by skipping the problematic buf_id and reaping the next entry, replacing the break with the next MSDU processing. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

libarchive version commit 5a98dcf8a86364b3c2c469c85b93647dfb139961 onwards (version v2.8.0 onwards) contains a CWE-835: Loop with Unreachable Exit Condition ('Infinite Loop') vulnerability in ISO9660 parser, archive_read_support_format_iso9660.c, read_CE()/parse_rockridge() that can result in DoS by infinite loop. This attack appears to be exploitable via the victim opening a specially crafted ISO9660 file.

In the Linux kernel, the following vulnerability has been resolved: PM / devfreq: Synchronize devfreq_monitor_[start/stop] There is a chance if a frequent switch of the governor done in a loop result in timer list corruption where timer cancel being done from two place one from cancel_delayed_work_sync() and followed by expire_timers() can be seen from the traces[1]. while true do echo "simple_ondemand" > /sys/class/devfreq/1d84000.ufshc/governor echo "performance" > /sys/class/devfreq/1d84000.ufshc/governor done It looks to be issue with devfreq driver where device_monitor_[start/stop] need to synchronized so that delayed work should get corrupted while it is either being queued or running or being cancelled. Let's use polling flag and devfreq lock to synchronize the queueing the timer instance twice and work data being corrupted. [1] ... .. <idle>-0 [003] 9436.209662: timer_cancel timer=0xffffff80444f0428 <idle>-0 [003] 9436.209664: timer_expire_entry timer=0xffffff80444f0428 now=0x10022da1c function=__typeid__ZTSFvP10timer_listE_global_addr baseclk=0x10022da1c <idle>-0 [003] 9436.209718: timer_expire_exit timer=0xffffff80444f0428 kworker/u16:6-14217 [003] 9436.209863: timer_start timer=0xffffff80444f0428 function=__typeid__ZTSFvP10timer_listE_global_addr expires=0x10022da2b now=0x10022da1c flags=182452227 vendor.xxxyyy.ha-1593 [004] 9436.209888: timer_cancel timer=0xffffff80444f0428 vendor.xxxyyy.ha-1593 [004] 9436.216390: timer_init timer=0xffffff80444f0428 vendor.xxxyyy.ha-1593 [004] 9436.216392: timer_start timer=0xffffff80444f0428 function=__typeid__ZTSFvP10timer_listE_global_addr expires=0x10022da2c now=0x10022da1d flags=186646532 vendor.xxxyyy.ha-1593 [005] 9436.220992: timer_cancel timer=0xffffff80444f0428 xxxyyyTraceManag-7795 [004] 9436.261641: timer_cancel timer=0xffffff80444f0428 [2] 9436.261653][ C4] Unable to handle kernel paging request at virtual address dead00000000012a [ 9436.261664][ C4] Mem abort info: [ 9436.261666][ C4] ESR = 0x96000044 [ 9436.261669][ C4] EC = 0x25: DABT (current EL), IL = 32 bits [ 9436.261671][ C4] SET = 0, FnV = 0 [ 9436.261673][ C4] EA = 0, S1PTW = 0 [ 9436.261675][ C4] Data abort info: [ 9436.261677][ C4] ISV = 0, ISS = 0x00000044 [ 9436.261680][ C4] CM = 0, WnR = 1 [ 9436.261682][ C4] [dead00000000012a] address between user and kernel address ranges [ 9436.261685][ C4] Internal error: Oops: 96000044 [#1] PREEMPT SMP [ 9436.261701][ C4] Skip md ftrace buffer dump for: 0x3a982d0 ... [ 9436.262138][ C4] CPU: 4 PID: 7795 Comm: TraceManag Tainted: G S W O 5.10.149-android12-9-o-g17f915d29d0c #1 [ 9436.262141][ C4] Hardware name: Qualcomm Technologies, Inc. (DT) [ 9436.262144][ C4] pstate: 22400085 (nzCv daIf +PAN -UAO +TCO BTYPE=--) [ 9436.262161][ C4] pc : expire_timers+0x9c/0x438 [ 9436.262164][ C4] lr : expire_timers+0x2a4/0x438 [ 9436.262168][ C4] sp : ffffffc010023dd0 [ 9436.262171][ C4] x29: ffffffc010023df0 x28: ffffffd0636fdc18 [ 9436.262178][ C4] x27: ffffffd063569dd0 x26: ffffffd063536008 [ 9436.262182][ C4] x25: 0000000000000001 x24: ffffff88f7c69280 [ 9436.262185][ C4] x23: 00000000000000e0 x22: dead000000000122 [ 9436.262188][ C4] x21: 000000010022da29 x20: ffffff8af72b4e80 [ 9436.262191][ C4] x19: ffffffc010023e50 x18: ffffffc010025038 [ 9436.262195][ C4] x17: 0000000000000240 x16: 0000000000000201 [ 9436.262199][ C4] x15: ffffffffffffffff x14: ffffff889f3c3100 [ 9436.262203][ C4] x13: ffffff889f3c3100 x12: 00000000049f56b8 [ 9436.262207][ C4] x11: 00000000049f56b8 x10: 00000000ffffffff [ 9436.262212][ C4] x9 : ffffffc010023e50 x8 : dead000000000122 [ 9436.262216][ C4] x7 : ffffffffffffffff x6 : ffffffc0100239d8 [ 9436.262220][ C4] x5 : 0000000000000000 x4 : 0000000000000101 [ 9436.262223][ C4] x3 : 0000000000000080 x2 : ffffff8 ---truncated---

A lack of CPU resource in the Linux kernel tracing module functionality in versions prior to 5.14-rc3 was found in the way user uses trace ring buffer in a specific way. Only privileged local users (with CAP_SYS_ADMIN capability) could use this flaw to starve the resources causing denial of service.

NVIDIA GPU Display Driver contains a vulnerability in the DirectX and OpenGL Usermode drivers where a specially crafted pixel shader can cause infinite recursion leading to denial of service.

In the Linux kernel, the following vulnerability has been resolved: netdevsim: avoid potential loop in nsim_dev_trap_report_work() Many syzbot reports include the following trace [1] If nsim_dev_trap_report_work() can not grab the mutex, it should rearm itself at least one jiffie later. [1] Sending NMI from CPU 1 to CPUs 0: NMI backtrace for cpu 0 CPU: 0 PID: 32383 Comm: kworker/0:2 Not tainted 6.8.0-rc2-syzkaller-00031-g861c0981648f #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023 Workqueue: events nsim_dev_trap_report_work RIP: 0010:bytes_is_nonzero mm/kasan/generic.c:89 [inline] RIP: 0010:memory_is_nonzero mm/kasan/generic.c:104 [inline] RIP: 0010:memory_is_poisoned_n mm/kasan/generic.c:129 [inline] RIP: 0010:memory_is_poisoned mm/kasan/generic.c:161 [inline] RIP: 0010:check_region_inline mm/kasan/generic.c:180 [inline] RIP: 0010:kasan_check_range+0x101/0x190 mm/kasan/generic.c:189 Code: 07 49 39 d1 75 0a 45 3a 11 b8 01 00 00 00 7c 0b 44 89 c2 e8 21 ed ff ff 83 f0 01 5b 5d 41 5c c3 48 85 d2 74 4f 48 01 ea eb 09 <48> 83 c0 01 48 39 d0 74 41 80 38 00 74 f2 eb b6 41 bc 08 00 00 00 RSP: 0018:ffffc90012dcf998 EFLAGS: 00000046 RAX: fffffbfff258af1e RBX: fffffbfff258af1f RCX: ffffffff8168eda3 RDX: fffffbfff258af1f RSI: 0000000000000004 RDI: ffffffff92c578f0 RBP: fffffbfff258af1e R08: 0000000000000000 R09: fffffbfff258af1e R10: ffffffff92c578f3 R11: ffffffff8acbcbc0 R12: 0000000000000002 R13: ffff88806db38400 R14: 1ffff920025b9f42 R15: ffffffff92c578e8 FS: 0000000000000000(0000) GS:ffff8880b9800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000c00994e078 CR3: 000000002c250000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <NMI> </NMI> <TASK> instrument_atomic_read include/linux/instrumented.h:68 [inline] atomic_read include/linux/atomic/atomic-instrumented.h:32 [inline] queued_spin_is_locked include/asm-generic/qspinlock.h:57 [inline] debug_spin_unlock kernel/locking/spinlock_debug.c:101 [inline] do_raw_spin_unlock+0x53/0x230 kernel/locking/spinlock_debug.c:141 __raw_spin_unlock_irqrestore include/linux/spinlock_api_smp.h:150 [inline] _raw_spin_unlock_irqrestore+0x22/0x70 kernel/locking/spinlock.c:194 debug_object_activate+0x349/0x540 lib/debugobjects.c:726 debug_work_activate kernel/workqueue.c:578 [inline] insert_work+0x30/0x230 kernel/workqueue.c:1650 __queue_work+0x62e/0x11d0 kernel/workqueue.c:1802 __queue_delayed_work+0x1bf/0x270 kernel/workqueue.c:1953 queue_delayed_work_on+0x106/0x130 kernel/workqueue.c:1989 queue_delayed_work include/linux/workqueue.h:563 [inline] schedule_delayed_work include/linux/workqueue.h:677 [inline] nsim_dev_trap_report_work+0x9c0/0xc80 drivers/net/netdevsim/dev.c:842 process_one_work+0x886/0x15d0 kernel/workqueue.c:2633 process_scheduled_works kernel/workqueue.c:2706 [inline] worker_thread+0x8b9/0x1290 kernel/workqueue.c:2787 kthread+0x2c6/0x3a0 kernel/kthread.c:388 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:242 </TASK>

Qemu before 2.0 block driver for Hyper-V VHDX Images is vulnerable to infinite loops and other potential issues when calculating BAT entries, due to missing bounds checks for block_size and logical_sector_size variables. These are used to derive other fields like 'sectors_per_block' etc. A user able to alter the Qemu disk image could ise this flaw to crash the Qemu instance resulting in DoS.

In the Linux kernel before 4.20.2, kernel/sched/fair.c mishandles leaf cfs_rq's, which allows attackers to cause a denial of service (infinite loop in update_blocked_averages) or possibly have unspecified other impact by inducing a high load.

An issue was discovered in dns.c in HAProxy through 1.8.14. In the case of a compressed pointer, a crafted packet can trigger infinite recursion by making the pointer point to itself, or create a long chain of valid pointers resulting in stack exhaustion.

In the Linux kernel, the following vulnerability has been resolved: x86/bhi: Avoid warning in #DB handler due to BHI mitigation When BHI mitigation is enabled, if SYSENTER is invoked with the TF flag set then entry_SYSENTER_compat() uses CLEAR_BRANCH_HISTORY and calls the clear_bhb_loop() before the TF flag is cleared. This causes the #DB handler (exc_debug_kernel()) to issue a warning because single-step is used outside the entry_SYSENTER_compat() function. To address this issue, entry_SYSENTER_compat() should use CLEAR_BRANCH_HISTORY after making sure the TF flag is cleared. The problem can be reproduced with the following sequence: $ cat sysenter_step.c int main() { asm("pushf; pop %ax; bts $8,%ax; push %ax; popf; sysenter"); } $ gcc -o sysenter_step sysenter_step.c $ ./sysenter_step Segmentation fault (core dumped) The program is expected to crash, and the #DB handler will issue a warning. Kernel log: WARNING: CPU: 27 PID: 7000 at arch/x86/kernel/traps.c:1009 exc_debug_kernel+0xd2/0x160 ... RIP: 0010:exc_debug_kernel+0xd2/0x160 ... Call Trace: <#DB> ? show_regs+0x68/0x80 ? __warn+0x8c/0x140 ? exc_debug_kernel+0xd2/0x160 ? report_bug+0x175/0x1a0 ? handle_bug+0x44/0x90 ? exc_invalid_op+0x1c/0x70 ? asm_exc_invalid_op+0x1f/0x30 ? exc_debug_kernel+0xd2/0x160 exc_debug+0x43/0x50 asm_exc_debug+0x1e/0x40 RIP: 0010:clear_bhb_loop+0x0/0xb0 ... </#DB> <TASK> ? entry_SYSENTER_compat_after_hwframe+0x6e/0x8d </TASK> [ bp: Massage commit message. ]

In the Linux kernel, the following vulnerability has been resolved: virtio_net: Do not send RSS key if it is not supported There is a bug when setting the RSS options in virtio_net that can break the whole machine, getting the kernel into an infinite loop. Running the following command in any QEMU virtual machine with virtionet will reproduce this problem: # ethtool -X eth0 hfunc toeplitz This is how the problem happens: 1) ethtool_set_rxfh() calls virtnet_set_rxfh() 2) virtnet_set_rxfh() calls virtnet_commit_rss_command() 3) virtnet_commit_rss_command() populates 4 entries for the rss scatter-gather 4) Since the command above does not have a key, then the last scatter-gatter entry will be zeroed, since rss_key_size == 0. sg_buf_size = vi->rss_key_size; 5) This buffer is passed to qemu, but qemu is not happy with a buffer with zero length, and do the following in virtqueue_map_desc() (QEMU function): if (!sz) { virtio_error(vdev, "virtio: zero sized buffers are not allowed"); 6) virtio_error() (also QEMU function) set the device as broken vdev->broken = true; 7) Qemu bails out, and do not repond this crazy kernel. 8) The kernel is waiting for the response to come back (function virtnet_send_command()) 9) The kernel is waiting doing the following : while (!virtqueue_get_buf(vi->cvq, &tmp) && !virtqueue_is_broken(vi->cvq)) cpu_relax(); 10) None of the following functions above is true, thus, the kernel loops here forever. Keeping in mind that virtqueue_is_broken() does not look at the qemu `vdev->broken`, so, it never realizes that the vitio is broken at QEMU side. Fix it by not sending RSS commands if the feature is not available in the device.

An issue was discovered in the Linux kernel before 5.8. arch/x86/kvm/svm/svm.c allows a set_memory_region_test infinite loop for certain nested page faults, aka CID-e72436bc3a52.

In Exiv2 0.26, Exiv2::PsdImage::readMetadata in psdimage.cpp in the PSD image reader may suffer from a denial of service (infinite loop) caused by an integer overflow via a crafted PSD image file.

In the Linux kernel, the following vulnerability has been resolved: fsdax: Fix infinite loop in dax_iomap_rw() I got an infinite loop and a WARNING report when executing a tail command in virtiofs. WARNING: CPU: 10 PID: 964 at fs/iomap/iter.c:34 iomap_iter+0x3a2/0x3d0 Modules linked in: CPU: 10 PID: 964 Comm: tail Not tainted 5.19.0-rc7 Call Trace: <TASK> dax_iomap_rw+0xea/0x620 ? __this_cpu_preempt_check+0x13/0x20 fuse_dax_read_iter+0x47/0x80 fuse_file_read_iter+0xae/0xd0 new_sync_read+0xfe/0x180 ? 0xffffffff81000000 vfs_read+0x14d/0x1a0 ksys_read+0x6d/0xf0 __x64_sys_read+0x1a/0x20 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd The tail command will call read() with a count of 0. In this case, iomap_iter() will report this WARNING, and always return 1 which casuing the infinite loop in dax_iomap_rw(). Fixing by checking count whether is 0 in dax_iomap_rw().

A flaw exists within the Linux kernel's handling of new TCP connections. The issue results from the lack of memory release after its effective lifetime. This vulnerability allows an unauthenticated attacker to create a denial of service condition on the system.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fixed integer types and null check locations [why]: issues fixed: - comparison with wider integer type in loop condition which can cause infinite loops - pointer dereference before null check

handler/ssl/OpenSslEngine.java in Netty 4.0.x before 4.0.37.Final and 4.1.x before 4.1.1.Final allows remote attackers to cause a denial of service (infinite loop).

A list management bug in BSS handling in the mac80211 stack in the Linux kernel 5.1 through 5.19.x before 5.19.16 could be used by local attackers (able to inject WLAN frames) to corrupt a linked list and, in turn, potentially execute code.

An improper handing of overflow in the UTF-8 decoder with supplementary characters can lead to an infinite loop in the decoder causing a Denial of Service. Versions Affected: Apache Tomcat 9.0.0.M9 to 9.0.7, 8.5.0 to 8.5.30, 8.0.0.RC1 to 8.0.51, and 7.0.28 to 7.0.86.

In the Linux kernel, the following vulnerability has been resolved: nvmet: Fix crash when a namespace is disabled The namespace percpu counter protects pending I/O, and we can only safely diable the namespace once the counter drop to zero. Otherwise we end up with a crash when running blktests/nvme/058 (eg for loop transport): [ 2352.930426] [ T53909] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN PTI [ 2352.930431] [ T53909] KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f] [ 2352.930434] [ T53909] CPU: 3 UID: 0 PID: 53909 Comm: kworker/u16:5 Tainted: G W 6.13.0-rc6 #232 [ 2352.930438] [ T53909] Tainted: [W]=WARN [ 2352.930440] [ T53909] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 [ 2352.930443] [ T53909] Workqueue: nvmet-wq nvme_loop_execute_work [nvme_loop] [ 2352.930449] [ T53909] RIP: 0010:blkcg_set_ioprio+0x44/0x180 as the queue is already torn down when calling submit_bio(); So we need to init the percpu counter in nvmet_ns_enable(), and wait for it to drop to zero in nvmet_ns_disable() to avoid having I/O pending after the namespace has been disabled.

A vulnerability was found in the way RemoteMessageChannel, introduced in jboss-remoting versions 3.3.10, reads from an empty buffer. An attacker could use this flaw to cause denial of service via high CPU caused by an infinite loop.

keycloak before version 4.0.0.final is vulnerable to a infinite loop in session replacement. A Keycloak cluster with multiple nodes could mishandle an expired session replacement and lead to an infinite loop. A malicious authenticated user could use this flaw to achieve Denial of Service on the server.

A denial of service vulnerability exists in Jenkins 2.153 and earlier, LTS 2.138.3 and earlier in CronTab.java that allows attackers with Overall/Read permission to have a request handling thread enter an infinite loop.

The fuse_fill_write_pages function in fs/fuse/file.c in the Linux kernel before 4.4 allows local users to cause a denial of service (infinite loop) via a writev system call that triggers a zero length for the first segment of an iov.

The process_tx_desc function in hw/net/e1000.c in QEMU before 2.4.0.1 does not properly process transmit descriptor data when sending a network packet, which allows attackers to cause a denial of service (infinite loop and guest crash) via unspecified vectors.