In the Linux kernel, the following vulnerability has been resolved: soc: qcom: geni-se: fix array underflow in geni_se_clk_tbl_get() This loop is supposed to break if the frequency returned from clk_round_rate() is the same as on the previous iteration. However, that check doesn't make sense on the first iteration through the loop. It leads to reading before the start of these->clk_perf_tbl[] array.

In the Linux kernel, the following vulnerability has been resolved: arm64: dts: imx8ulp: correct the flexspi compatible string The flexspi on imx8ulp only has 16 LUTs, and imx8mm flexspi has 32 LUTs, so correct the compatible string here, otherwise will meet below error: [ 1.119072] ------------[ cut here ]------------ [ 1.123926] WARNING: CPU: 0 PID: 1 at drivers/spi/spi-nxp-fspi.c:855 nxp_fspi_exec_op+0xb04/0xb64 [ 1.133239] Modules linked in: [ 1.136448] CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.11.0-rc6-next-20240902-00001-g131bf9439dd9 #69 [ 1.146821] Hardware name: NXP i.MX8ULP EVK (DT) [ 1.151647] pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 1.158931] pc : nxp_fspi_exec_op+0xb04/0xb64 [ 1.163496] lr : nxp_fspi_exec_op+0xa34/0xb64 [ 1.168060] sp : ffff80008002b2a0 [ 1.171526] x29: ffff80008002b2d0 x28: 0000000000000000 x27: 0000000000000000 [ 1.179002] x26: ffff2eb645542580 x25: ffff800080610014 x24: ffff800080610000 [ 1.186480] x23: ffff2eb645548080 x22: 0000000000000006 x21: ffff2eb6455425e0 [ 1.193956] x20: 0000000000000000 x19: ffff80008002b5e0 x18: ffffffffffffffff [ 1.201432] x17: ffff2eb644467508 x16: 0000000000000138 x15: 0000000000000002 [ 1.208907] x14: 0000000000000000 x13: ffff2eb6400d8080 x12: 00000000ffffff00 [ 1.216378] x11: 0000000000000000 x10: ffff2eb6400d8080 x9 : ffff2eb697adca80 [ 1.223850] x8 : ffff2eb697ad3cc0 x7 : 0000000100000000 x6 : 0000000000000001 [ 1.231324] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 00000000000007a6 [ 1.238795] x2 : 0000000000000000 x1 : 00000000000001ce x0 : 00000000ffffff92 [ 1.246267] Call trace: [ 1.248824] nxp_fspi_exec_op+0xb04/0xb64 [ 1.253031] spi_mem_exec_op+0x3a0/0x430 [ 1.257139] spi_nor_read_id+0x80/0xcc [ 1.261065] spi_nor_scan+0x1ec/0xf10 [ 1.264901] spi_nor_probe+0x108/0x2fc [ 1.268828] spi_mem_probe+0x6c/0xbc [ 1.272574] spi_probe+0x84/0xe4 [ 1.275958] really_probe+0xbc/0x29c [ 1.279713] __driver_probe_device+0x78/0x12c [ 1.284277] driver_probe_device+0xd8/0x15c [ 1.288660] __device_attach_driver+0xb8/0x134 [ 1.293316] bus_for_each_drv+0x88/0xe8 [ 1.297337] __device_attach+0xa0/0x190 [ 1.301353] device_initial_probe+0x14/0x20 [ 1.305734] bus_probe_device+0xac/0xb0 [ 1.309752] device_add+0x5d0/0x790 [ 1.313408] __spi_add_device+0x134/0x204 [ 1.317606] of_register_spi_device+0x3b4/0x590 [ 1.322348] spi_register_controller+0x47c/0x754 [ 1.327181] devm_spi_register_controller+0x4c/0xa4 [ 1.332289] nxp_fspi_probe+0x1cc/0x2b0 [ 1.336307] platform_probe+0x68/0xc4 [ 1.340145] really_probe+0xbc/0x29c [ 1.343893] __driver_probe_device+0x78/0x12c [ 1.348457] driver_probe_device+0xd8/0x15c [ 1.352838] __driver_attach+0x90/0x19c [ 1.356857] bus_for_each_dev+0x7c/0xdc [ 1.360877] driver_attach+0x24/0x30 [ 1.364624] bus_add_driver+0xe4/0x208 [ 1.368552] driver_register+0x5c/0x124 [ 1.372573] __platform_driver_register+0x28/0x34 [ 1.377497] nxp_fspi_driver_init+0x1c/0x28 [ 1.381888] do_one_initcall+0x80/0x1c8 [ 1.385908] kernel_init_freeable+0x1c4/0x28c [ 1.390472] kernel_init+0x20/0x1d8 [ 1.394138] ret_from_fork+0x10/0x20 [ 1.397885] ---[ end trace 0000000000000000 ]--- [ 1.407908] ------------[ cut here ]------------

In the Linux kernel, the following vulnerability has been resolved: crypto: qat/qat_420xx - fix off by one in uof_get_name() This is called from uof_get_name_420xx() where "num_objs" is the ARRAY_SIZE() of fw_objs[]. The > needs to be >= to prevent an out of bounds access.

In the Linux kernel, the following vulnerability has been resolved: tpm: Lock TPM chip in tpm_pm_suspend() first Setting TPM_CHIP_FLAG_SUSPENDED in the end of tpm_pm_suspend() can be racy according, as this leaves window for tpm_hwrng_read() to be called while the operation is in progress. The recent bug report gives also evidence of this behaviour. Aadress this by locking the TPM chip before checking any chip->flags both in tpm_pm_suspend() and tpm_hwrng_read(). Move TPM_CHIP_FLAG_SUSPENDED check inside tpm_get_random() so that it will be always checked only when the lock is reserved.

In the Linux kernel, the following vulnerability has been resolved: drm/rockchip: vop: Fix a dereferenced before check warning The 'state' can't be NULL, we should check crtc_state. Fix warning: drivers/gpu/drm/rockchip/rockchip_drm_vop.c:1096 vop_plane_atomic_async_check() warn: variable dereferenced before check 'state' (see line 1077)

In the Linux kernel, the following vulnerability has been resolved: virtio_pci: Fix admin vq cleanup by using correct info pointer vp_modern_avq_cleanup() and vp_del_vqs() clean up admin vq resources by virtio_pci_vq_info pointer. The info pointer of admin vq is stored in vp_dev->admin_vq.info instead of vp_dev->vqs[]. Using the info pointer from vp_dev->vqs[] for admin vq causes a kernel NULL pointer dereference bug. In vp_modern_avq_cleanup() and vp_del_vqs(), get the info pointer from vp_dev->admin_vq.info for admin vq to clean up the resources. Also make info ptr as argument of vp_del_vq() to be symmetric with vp_setup_vq(). vp_reset calls vp_modern_avq_cleanup, and causes the Call Trace: ================================================================== BUG: kernel NULL pointer dereference, address:0000000000000000 ... CPU: 49 UID: 0 PID: 4439 Comm: modprobe Not tainted 6.11.0-rc5 #1 RIP: 0010:vp_reset+0x57/0x90 [virtio_pci] Call Trace: <TASK> ... ? vp_reset+0x57/0x90 [virtio_pci] ? vp_reset+0x38/0x90 [virtio_pci] virtio_reset_device+0x1d/0x30 remove_vq_common+0x1c/0x1a0 [virtio_net] virtnet_remove+0xa1/0xc0 [virtio_net] virtio_dev_remove+0x46/0xa0 ... virtio_pci_driver_exit+0x14/0x810 [virtio_pci] ==================================================================

In the Linux kernel, the following vulnerability has been resolved: bpf: sync_linked_regs() must preserve subreg_def Range propagation must not affect subreg_def marks, otherwise the following example is rewritten by verifier incorrectly when BPF_F_TEST_RND_HI32 flag is set: 0: call bpf_ktime_get_ns call bpf_ktime_get_ns 1: r0 &= 0x7fffffff after verifier r0 &= 0x7fffffff 2: w1 = w0 rewrites w1 = w0 3: if w0 < 10 goto +0 --------------> r11 = 0x2f5674a6 (r) 4: r1 >>= 32 r11 <<= 32 (r) 5: r0 = r1 r1 |= r11 (r) 6: exit; if w0 < 0xa goto pc+0 r1 >>= 32 r0 = r1 exit (or zero extension of w1 at (2) is missing for architectures that require zero extension for upper register half). The following happens w/o this patch: - r0 is marked as not a subreg at (0); - w1 is marked as subreg at (2); - w1 subreg_def is overridden at (3) by copy_register_state(); - w1 is read at (5) but mark_insn_zext() does not mark (2) for zero extension, because w1 subreg_def is not set; - because of BPF_F_TEST_RND_HI32 flag verifier inserts random value for hi32 bits of (2) (marked (r)); - this random value is read at (5).

In the Linux kernel, the following vulnerability has been resolved: svcrdma: fix miss destroy percpu_counter in svc_rdma_proc_init() There's issue as follows: RPC: Registered rdma transport module. RPC: Registered rdma backchannel transport module. RPC: Unregistered rdma transport module. RPC: Unregistered rdma backchannel transport module. BUG: unable to handle page fault for address: fffffbfff80c609a PGD 123fee067 P4D 123fee067 PUD 123fea067 PMD 10c624067 PTE 0 Oops: Oops: 0000 [#1] PREEMPT SMP KASAN NOPTI RIP: 0010:percpu_counter_destroy_many+0xf7/0x2a0 Call Trace: <TASK> __die+0x1f/0x70 page_fault_oops+0x2cd/0x860 spurious_kernel_fault+0x36/0x450 do_kern_addr_fault+0xca/0x100 exc_page_fault+0x128/0x150 asm_exc_page_fault+0x26/0x30 percpu_counter_destroy_many+0xf7/0x2a0 mmdrop+0x209/0x350 finish_task_switch.isra.0+0x481/0x840 schedule_tail+0xe/0xd0 ret_from_fork+0x23/0x80 ret_from_fork_asm+0x1a/0x30 </TASK> If register_sysctl() return NULL, then svc_rdma_proc_cleanup() will not destroy the percpu counters which init in svc_rdma_proc_init(). If CONFIG_HOTPLUG_CPU is enabled, residual nodes may be in the 'percpu_counters' list. The above issue may occur once the module is removed. If the CONFIG_HOTPLUG_CPU configuration is not enabled, memory leakage occurs. To solve above issue just destroy all percpu counters when register_sysctl() return NULL.

In the Linux kernel, the following vulnerability has been resolved: ASoC: dapm: fix bounds checker error in dapm_widget_list_create The widgets array in the snd_soc_dapm_widget_list has a __counted_by attribute attached to it, which points to the num_widgets variable. This attribute is used in bounds checking, and if it is not set before the array is filled, then the bounds sanitizer will issue a warning or a kernel panic if CONFIG_UBSAN_TRAP is set. This patch sets the size of the widgets list calculated with list_for_each as the initial value for num_widgets as it is used for allocating memory for the array. It is updated with the actual number of added elements after the array is filled.

In the Linux kernel, the following vulnerability has been resolved: svcrdma: Address an integer overflow Dan Carpenter reports: > Commit 78147ca8b4a9 ("svcrdma: Add a "parsed chunk list" data > structure") from Jun 22, 2020 (linux-next), leads to the following > Smatch static checker warning: > > net/sunrpc/xprtrdma/svc_rdma_recvfrom.c:498 xdr_check_write_chunk() > warn: potential user controlled sizeof overflow 'segcount * 4 * 4' > > net/sunrpc/xprtrdma/svc_rdma_recvfrom.c > 488 static bool xdr_check_write_chunk(struct svc_rdma_recv_ctxt *rctxt) > 489 { > 490 u32 segcount; > 491 __be32 *p; > 492 > 493 if (xdr_stream_decode_u32(&rctxt->rc_stream, &segcount)) > ^^^^^^^^ > > 494 return false; > 495 > 496 /* A bogus segcount causes this buffer overflow check to fail. */ > 497 p = xdr_inline_decode(&rctxt->rc_stream, > --> 498 segcount * rpcrdma_segment_maxsz * sizeof(*p)); > > > segcount is an untrusted u32. On 32bit systems anything >= SIZE_MAX / 16 will > have an integer overflow and some those values will be accepted by > xdr_inline_decode().

In the Linux kernel, the following vulnerability has been resolved: xen: Fix the issue of resource not being properly released in xenbus_dev_probe() This patch fixes an issue in the function xenbus_dev_probe(). In the xenbus_dev_probe() function, within the if (err) branch at line 313, the program incorrectly returns err directly without releasing the resources allocated by err = drv->probe(dev, id). As the return value is non-zero, the upper layers assume the processing logic has failed. However, the probe operation was performed earlier without a corresponding remove operation. Since the probe actually allocates resources, failing to perform the remove operation could lead to problems. To fix this issue, we followed the resource release logic of the xenbus_dev_remove() function by adding a new block fail_remove before the fail_put block. After entering the branch if (err) at line 313, the function will use a goto statement to jump to the fail_remove block, ensuring that the previously acquired resources are correctly released, thus preventing the reference count leak. This bug was identified by an experimental static analysis tool developed by our team. The tool specializes in analyzing reference count operations and detecting potential issues where resources are not properly managed. In this case, the tool flagged the missing release operation as a potential problem, which led to the development of this patch.

In the Linux kernel, the following vulnerability has been resolved: virtio/vsock: Fix accept_queue memory leak As the final stages of socket destruction may be delayed, it is possible that virtio_transport_recv_listen() will be called after the accept_queue has been flushed, but before the SOCK_DONE flag has been set. As a result, sockets enqueued after the flush would remain unremoved, leading to a memory leak. vsock_release __vsock_release lock virtio_transport_release virtio_transport_close schedule_delayed_work(close_work) sk_shutdown = SHUTDOWN_MASK (!) flush accept_queue release virtio_transport_recv_pkt vsock_find_bound_socket lock if flag(SOCK_DONE) return virtio_transport_recv_listen child = vsock_create_connected (!) vsock_enqueue_accept(child) release close_work lock virtio_transport_do_close set_flag(SOCK_DONE) virtio_transport_remove_sock vsock_remove_sock vsock_remove_bound release Introduce a sk_shutdown check to disallow vsock_enqueue_accept() during socket destruction. unreferenced object 0xffff888109e3f800 (size 2040): comm "kworker/5:2", pid 371, jiffies 4294940105 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 28 00 0b 40 00 00 00 00 00 00 00 00 00 00 00 00 (..@............ backtrace (crc 9e5f4e84): [<ffffffff81418ff1>] kmem_cache_alloc_noprof+0x2c1/0x360 [<ffffffff81d27aa0>] sk_prot_alloc+0x30/0x120 [<ffffffff81d2b54c>] sk_alloc+0x2c/0x4b0 [<ffffffff81fe049a>] __vsock_create.constprop.0+0x2a/0x310 [<ffffffff81fe6d6c>] virtio_transport_recv_pkt+0x4dc/0x9a0 [<ffffffff81fe745d>] vsock_loopback_work+0xfd/0x140 [<ffffffff810fc6ac>] process_one_work+0x20c/0x570 [<ffffffff810fce3f>] worker_thread+0x1bf/0x3a0 [<ffffffff811070dd>] kthread+0xdd/0x110 [<ffffffff81044fdd>] ret_from_fork+0x2d/0x50 [<ffffffff8100785a>] ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: fix fault at system suspend if device was already runtime suspended If the device was already runtime suspended then during system suspend we cannot access the device registers else it will crash. Also we cannot access any registers after dwc3_core_exit() on some platforms so move the dwc3_enable_susphy() call to the top.

In the Linux kernel, the following vulnerability has been resolved: virtiofs: use pages instead of pointer for kernel direct IO When trying to insert a 10MB kernel module kept in a virtio-fs with cache disabled, the following warning was reported: ------------[ cut here ]------------ WARNING: CPU: 1 PID: 404 at mm/page_alloc.c:4551 ...... Modules linked in: CPU: 1 PID: 404 Comm: insmod Not tainted 6.9.0-rc5+ #123 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) ...... RIP: 0010:__alloc_pages+0x2bf/0x380 ...... Call Trace: <TASK> ? __warn+0x8e/0x150 ? __alloc_pages+0x2bf/0x380 __kmalloc_large_node+0x86/0x160 __kmalloc+0x33c/0x480 virtio_fs_enqueue_req+0x240/0x6d0 virtio_fs_wake_pending_and_unlock+0x7f/0x190 queue_request_and_unlock+0x55/0x60 fuse_simple_request+0x152/0x2b0 fuse_direct_io+0x5d2/0x8c0 fuse_file_read_iter+0x121/0x160 __kernel_read+0x151/0x2d0 kernel_read+0x45/0x50 kernel_read_file+0x1a9/0x2a0 init_module_from_file+0x6a/0xe0 idempotent_init_module+0x175/0x230 __x64_sys_finit_module+0x5d/0xb0 x64_sys_call+0x1c3/0x9e0 do_syscall_64+0x3d/0xc0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 ...... </TASK> ---[ end trace 0000000000000000 ]--- The warning is triggered as follows: 1) syscall finit_module() handles the module insertion and it invokes kernel_read_file() to read the content of the module first. 2) kernel_read_file() allocates a 10MB buffer by using vmalloc() and passes it to kernel_read(). kernel_read() constructs a kvec iter by using iov_iter_kvec() and passes it to fuse_file_read_iter(). 3) virtio-fs disables the cache, so fuse_file_read_iter() invokes fuse_direct_io(). As for now, the maximal read size for kvec iter is only limited by fc->max_read. For virtio-fs, max_read is UINT_MAX, so fuse_direct_io() doesn't split the 10MB buffer. It saves the address and the size of the 10MB-sized buffer in out_args[0] of a fuse request and passes the fuse request to virtio_fs_wake_pending_and_unlock(). 4) virtio_fs_wake_pending_and_unlock() uses virtio_fs_enqueue_req() to queue the request. Because virtiofs need DMA-able address, so virtio_fs_enqueue_req() uses kmalloc() to allocate a bounce buffer for all fuse args, copies these args into the bounce buffer and passed the physical address of the bounce buffer to virtiofsd. The total length of these fuse args for the passed fuse request is about 10MB, so copy_args_to_argbuf() invokes kmalloc() with a 10MB size parameter and it triggers the warning in __alloc_pages(): if (WARN_ON_ONCE_GFP(order > MAX_PAGE_ORDER, gfp)) return NULL; 5) virtio_fs_enqueue_req() will retry the memory allocation in a kworker, but it won't help, because kmalloc() will always return NULL due to the abnormal size and finit_module() will hang forever. A feasible solution is to limit the value of max_read for virtio-fs, so the length passed to kmalloc() will be limited. However it will affect the maximal read size for normal read. And for virtio-fs write initiated from kernel, it has the similar problem but now there is no way to limit fc->max_write in kernel. So instead of limiting both the values of max_read and max_write in kernel, introducing use_pages_for_kvec_io in fuse_conn and setting it as true in virtiofs. When use_pages_for_kvec_io is enabled, fuse will use pages instead of pointer to pass the KVEC_IO data. After switching to pages for KVEC_IO data, these pages will be used for DMA through virtio-fs. If these pages are backed by vmalloc(), {flush|invalidate}_kernel_vmap_range() are necessary to flush or invalidate the cache before the DMA operation. So add two new fields in fuse_args_pages to record the base address of vmalloc area and the condition indicating whether invalidation is needed. Perform the flush in fuse_get_user_pages() for write operations and the invalidation in fuse_release_user_pages() for read operations. It may seem necessary to introduce another fie ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm: zynqmp_dp: Fix integer overflow in zynqmp_dp_rate_get() This patch fixes a potential integer overflow in the zynqmp_dp_rate_get() The issue comes up when the expression drm_dp_bw_code_to_link_rate(dp->test.bw_code) * 10000 is evaluated using 32-bit Now the constant is a compatible 64-bit type. Resolves coverity issues: CID 1636340 and CID 1635811

In the Linux kernel, the following vulnerability has been resolved: xfs: fix log recovery buffer allocation for the legacy h_size fixup Commit a70f9fe52daa ("xfs: detect and handle invalid iclog size set by mkfs") added a fixup for incorrect h_size values used for the initial umount record in old xfsprogs versions. Later commit 0c771b99d6c9 ("xfs: clean up calculation of LR header blocks") cleaned up the log reover buffer calculation, but stoped using the fixed up h_size value to size the log recovery buffer, which can lead to an out of bounds access when the incorrect h_size does not come from the old mkfs tool, but a fuzzer. Fix this by open coding xlog_logrec_hblks and taking the fixed h_size into account for this calculation.

In the Linux kernel, the following vulnerability has been resolved: powerpc/pseries: Whitelist dtl slub object for copying to userspace Reading the dispatch trace log from /sys/kernel/debug/powerpc/dtl/cpu-* results in a BUG() when the config CONFIG_HARDENED_USERCOPY is enabled as shown below. kernel BUG at mm/usercopy.c:102! Oops: Exception in kernel mode, sig: 5 [#1] LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries Modules linked in: xfs libcrc32c dm_service_time sd_mod t10_pi sg ibmvfc scsi_transport_fc ibmveth pseries_wdt dm_multipath dm_mirror dm_region_hash dm_log dm_mod fuse CPU: 27 PID: 1815 Comm: python3 Not tainted 6.10.0-rc3 #85 Hardware name: IBM,9040-MRX POWER10 (raw) 0x800200 0xf000006 of:IBM,FW1060.00 (NM1060_042) hv:phyp pSeries NIP: c0000000005d23d4 LR: c0000000005d23d0 CTR: 00000000006ee6f8 REGS: c000000120c078c0 TRAP: 0700 Not tainted (6.10.0-rc3) MSR: 8000000000029033 <SF,EE,ME,IR,DR,RI,LE> CR: 2828220f XER: 0000000e CFAR: c0000000001fdc80 IRQMASK: 0 [ ... GPRs omitted ... ] NIP [c0000000005d23d4] usercopy_abort+0x78/0xb0 LR [c0000000005d23d0] usercopy_abort+0x74/0xb0 Call Trace: usercopy_abort+0x74/0xb0 (unreliable) __check_heap_object+0xf8/0x120 check_heap_object+0x218/0x240 __check_object_size+0x84/0x1a4 dtl_file_read+0x17c/0x2c4 full_proxy_read+0x8c/0x110 vfs_read+0xdc/0x3a0 ksys_read+0x84/0x144 system_call_exception+0x124/0x330 system_call_vectored_common+0x15c/0x2ec --- interrupt: 3000 at 0x7fff81f3ab34 Commit 6d07d1cd300f ("usercopy: Restrict non-usercopy caches to size 0") requires that only whitelisted areas in slab/slub objects can be copied to userspace when usercopy hardening is enabled using CONFIG_HARDENED_USERCOPY. Dtl contains hypervisor dispatch events which are expected to be read by privileged users. Hence mark this safe for user access. Specify useroffset=0 and usersize=DISPATCH_LOG_BYTES to whitelist the entire object.

In the Linux kernel, the following vulnerability has been resolved: drm/msm/gem: prevent integer overflow in msm_ioctl_gem_submit() The "submit->cmd[i].size" and "submit->cmd[i].offset" variables are u32 values that come from the user via the submit_lookup_cmds() function. This addition could lead to an integer wrapping bug so use size_add() to prevent that. Patchwork: https://patchwork.freedesktop.org/patch/624696/

The n_tty_write function in drivers/tty/n_tty.c in the Linux kernel through 3.14.3 does not properly manage tty driver access in the "LECHO & !OPOST" case, which allows local users to cause a denial of service (memory corruption and system crash) or gain privileges by triggering a race condition involving read and write operations with long strings.

A memory leak flaw was found in the Linux kernel in the ccp_run_aes_gcm_cmd() function in drivers/crypto/ccp/ccp-ops.c, which allows attackers to cause a denial of service (memory consumption). This vulnerability is similar with the older CVE-2019-18808.

In the Linux kernel, the following vulnerability has been resolved: spi: hisi-kunpeng: Add verification for the max_frequency provided by the firmware If the value of max_speed_hz is 0, it may cause a division by zero error in hisi_calc_effective_speed(). The value of max_speed_hz is provided by firmware. Firmware is generally considered as a trusted domain. However, as division by zero errors can cause system failure, for defense measure, the value of max_speed is validated here. So 0 is regarded as invalid and an error code is returned.

A memory leak flaw was found in the Linux kernel's ccp_run_aes_gcm_cmd() function that allows an attacker to cause a denial of service. The vulnerability is similar to the older CVE-2019-18808. The highest threat from this vulnerability is to system availability.

In the Linux kernel, the following vulnerability has been resolved: lib/test_hmm.c: handle src_pfns and dst_pfns allocation failure The kcalloc() in dmirror_device_evict_chunk() will return null if the physical memory has run out. As a result, if src_pfns or dst_pfns is dereferenced, the null pointer dereference bug will happen. Moreover, the device is going away. If the kcalloc() fails, the pages mapping a chunk could not be evicted. So add a __GFP_NOFAIL flag in kcalloc(). Finally, as there is no need to have physically contiguous memory, Switch kcalloc() to kvcalloc() in order to avoid failing allocations.

A null pointer dereference issue was discovered in fs/io_uring.c in the Linux kernel before 5.15.62. A local user could use this flaw to crash the system or potentially cause a denial of service.

In the Linux kernel, the following vulnerability has been resolved: drm/tests: hdmi: Fix memory leaks in drm_display_mode_from_cea_vic() modprobe drm_hdmi_state_helper_test and then rmmod it, the following memory leak occurs. The `mode` allocated in drm_mode_duplicate() called by drm_display_mode_from_cea_vic() is not freed, which cause the memory leak: unreferenced object 0xffffff80ccd18100 (size 128): comm "kunit_try_catch", pid 1851, jiffies 4295059695 hex dump (first 32 bytes): 57 62 00 00 80 02 90 02 f0 02 20 03 00 00 e0 01 Wb........ ..... ea 01 ec 01 0d 02 00 00 0a 00 00 00 00 00 00 00 ................ backtrace (crc c2f1aa95): [<000000000f10b11b>] kmemleak_alloc+0x34/0x40 [<000000001cd4cf73>] __kmalloc_cache_noprof+0x26c/0x2f4 [<00000000f1f3cffa>] drm_mode_duplicate+0x44/0x19c [<000000008cbeef13>] drm_display_mode_from_cea_vic+0x88/0x98 [<0000000019daaacf>] 0xffffffedc11ae69c [<000000000aad0f85>] kunit_try_run_case+0x13c/0x3ac [<00000000a9210bac>] kunit_generic_run_threadfn_adapter+0x80/0xec [<000000000a0b2e9e>] kthread+0x2e8/0x374 [<00000000bd668858>] ret_from_fork+0x10/0x20 ...... Free `mode` by using drm_kunit_display_mode_from_cea_vic() to fix it.

In the Linux kernel, the following vulnerability has been resolved: btrfs: reject ro->rw reconfiguration if there are hard ro requirements [BUG] Syzbot reports the following crash: BTRFS info (device loop0 state MCS): disabling free space tree BTRFS info (device loop0 state MCS): clearing compat-ro feature flag for FREE_SPACE_TREE (0x1) BTRFS info (device loop0 state MCS): clearing compat-ro feature flag for FREE_SPACE_TREE_VALID (0x2) Oops: general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 RIP: 0010:backup_super_roots fs/btrfs/disk-io.c:1691 [inline] RIP: 0010:write_all_supers+0x97a/0x40f0 fs/btrfs/disk-io.c:4041 Call Trace: <TASK> btrfs_commit_transaction+0x1eae/0x3740 fs/btrfs/transaction.c:2530 btrfs_delete_free_space_tree+0x383/0x730 fs/btrfs/free-space-tree.c:1312 btrfs_start_pre_rw_mount+0xf28/0x1300 fs/btrfs/disk-io.c:3012 btrfs_remount_rw fs/btrfs/super.c:1309 [inline] btrfs_reconfigure+0xae6/0x2d40 fs/btrfs/super.c:1534 btrfs_reconfigure_for_mount fs/btrfs/super.c:2020 [inline] btrfs_get_tree_subvol fs/btrfs/super.c:2079 [inline] btrfs_get_tree+0x918/0x1920 fs/btrfs/super.c:2115 vfs_get_tree+0x90/0x2b0 fs/super.c:1800 do_new_mount+0x2be/0xb40 fs/namespace.c:3472 do_mount fs/namespace.c:3812 [inline] __do_sys_mount fs/namespace.c:4020 [inline] __se_sys_mount+0x2d6/0x3c0 fs/namespace.c:3997 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f [CAUSE] To support mounting different subvolume with different RO/RW flags for the new mount APIs, btrfs introduced two workaround to support this feature: - Skip mount option/feature checks if we are mounting a different subvolume - Reconfigure the fs to RW if the initial mount is RO Combining these two, we can have the following sequence: - Mount the fs ro,rescue=all,clear_cache,space_cache=v1 rescue=all will mark the fs as hard read-only, so no v2 cache clearing will happen. - Mount a subvolume rw of the same fs. We go into btrfs_get_tree_subvol(), but fc_mount() returns EBUSY because our new fc is RW, different from the original fs. Now we enter btrfs_reconfigure_for_mount(), which switches the RO flag first so that we can grab the existing fs_info. Then we reconfigure the fs to RW. - During reconfiguration, option/features check is skipped This means we will restart the v2 cache clearing, and convert back to v1 cache. This will trigger fs writes, and since the original fs has "rescue=all" option, it skips the csum tree read. And eventually causing NULL pointer dereference in super block writeback. [FIX] For reconfiguration caused by different subvolume RO/RW flags, ensure we always run btrfs_check_options() to ensure we have proper hard RO requirements met. In fact the function btrfs_check_options() doesn't really do many complex checks, but hard RO requirement and some feature dependency checks, thus there is no special reason not to do the check for mount reconfiguration.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Don't call cleanup on profile rollback failure When profile rollback fails in mlx5e_netdev_change_profile, the netdev profile var is left set to NULL. Avoid a crash when unloading the driver by not calling profile->cleanup in such a case. This was encountered while testing, with the original trigger that the wq rescuer thread creation got interrupted (presumably due to Ctrl+C-ing modprobe), which gets converted to ENOMEM (-12) by mlx5e_priv_init, the profile rollback also fails for the same reason (signal still active) so the profile is left as NULL, leading to a crash later in _mlx5e_remove. [ 732.473932] mlx5_core 0000:08:00.1: E-Switch: Unload vfs: mode(OFFLOADS), nvfs(2), necvfs(0), active vports(2) [ 734.525513] workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR [ 734.557372] mlx5_core 0000:08:00.1: mlx5e_netdev_init_profile:6235:(pid 6086): mlx5e_priv_init failed, err=-12 [ 734.559187] mlx5_core 0000:08:00.1 eth3: mlx5e_netdev_change_profile: new profile init failed, -12 [ 734.560153] workqueue: Failed to create a rescuer kthread for wq "mlx5e": -EINTR [ 734.589378] mlx5_core 0000:08:00.1: mlx5e_netdev_init_profile:6235:(pid 6086): mlx5e_priv_init failed, err=-12 [ 734.591136] mlx5_core 0000:08:00.1 eth3: mlx5e_netdev_change_profile: failed to rollback to orig profile, -12 [ 745.537492] BUG: kernel NULL pointer dereference, address: 0000000000000008 [ 745.538222] #PF: supervisor read access in kernel mode <snipped> [ 745.551290] Call Trace: [ 745.551590] <TASK> [ 745.551866] ? __die+0x20/0x60 [ 745.552218] ? page_fault_oops+0x150/0x400 [ 745.555307] ? exc_page_fault+0x79/0x240 [ 745.555729] ? asm_exc_page_fault+0x22/0x30 [ 745.556166] ? mlx5e_remove+0x6b/0xb0 [mlx5_core] [ 745.556698] auxiliary_bus_remove+0x18/0x30 [ 745.557134] device_release_driver_internal+0x1df/0x240 [ 745.557654] bus_remove_device+0xd7/0x140 [ 745.558075] device_del+0x15b/0x3c0 [ 745.558456] mlx5_rescan_drivers_locked.part.0+0xb1/0x2f0 [mlx5_core] [ 745.559112] mlx5_unregister_device+0x34/0x50 [mlx5_core] [ 745.559686] mlx5_uninit_one+0x46/0xf0 [mlx5_core] [ 745.560203] remove_one+0x4e/0xd0 [mlx5_core] [ 745.560694] pci_device_remove+0x39/0xa0 [ 745.561112] device_release_driver_internal+0x1df/0x240 [ 745.561631] driver_detach+0x47/0x90 [ 745.562022] bus_remove_driver+0x84/0x100 [ 745.562444] pci_unregister_driver+0x3b/0x90 [ 745.562890] mlx5_cleanup+0xc/0x1b [mlx5_core] [ 745.563415] __x64_sys_delete_module+0x14d/0x2f0 [ 745.563886] ? kmem_cache_free+0x1b0/0x460 [ 745.564313] ? lockdep_hardirqs_on_prepare+0xe2/0x190 [ 745.564825] do_syscall_64+0x6d/0x140 [ 745.565223] entry_SYSCALL_64_after_hwframe+0x4b/0x53 [ 745.565725] RIP: 0033:0x7f1579b1288b

In the Linux kernel, the following vulnerability has been resolved: resource,kexec: walk_system_ram_res_rev must retain resource flags walk_system_ram_res_rev() erroneously discards resource flags when passing the information to the callback. This causes systems with IORESOURCE_SYSRAM_DRIVER_MANAGED memory to have these resources selected during kexec to store kexec buffers if that memory happens to be at placed above normal system ram. This leads to undefined behavior after reboot. If the kexec buffer is never touched, nothing happens. If the kexec buffer is touched, it could lead to a crash (like below) or undefined behavior. Tested on a system with CXL memory expanders with driver managed memory, TPM enabled, and CONFIG_IMA_KEXEC=y. Adding printk's showed the flags were being discarded and as a result the check for IORESOURCE_SYSRAM_DRIVER_MANAGED passes. find_next_iomem_res: name(System RAM (kmem)) start(10000000000) end(1034fffffff) flags(83000200) locate_mem_hole_top_down: start(10000000000) end(1034fffffff) flags(0) [.] BUG: unable to handle page fault for address: ffff89834ffff000 [.] #PF: supervisor read access in kernel mode [.] #PF: error_code(0x0000) - not-present page [.] PGD c04c8bf067 P4D c04c8bf067 PUD c04c8be067 PMD 0 [.] Oops: 0000 [#1] SMP [.] RIP: 0010:ima_restore_measurement_list+0x95/0x4b0 [.] RSP: 0018:ffffc900000d3a80 EFLAGS: 00010286 [.] RAX: 0000000000001000 RBX: 0000000000000000 RCX: ffff89834ffff000 [.] RDX: 0000000000000018 RSI: ffff89834ffff000 RDI: ffff89834ffff018 [.] RBP: ffffc900000d3ba0 R08: 0000000000000020 R09: ffff888132b8a900 [.] R10: 4000000000000000 R11: 000000003a616d69 R12: 0000000000000000 [.] R13: ffffffff8404ac28 R14: 0000000000000000 R15: ffff89834ffff000 [.] FS: 0000000000000000(0000) GS:ffff893d44640000(0000) knlGS:0000000000000000 [.] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [.] ata5: SATA link down (SStatus 0 SControl 300) [.] CR2: ffff89834ffff000 CR3: 000001034d00f001 CR4: 0000000000770ef0 [.] PKRU: 55555554 [.] Call Trace: [.] <TASK> [.] ? __die+0x78/0xc0 [.] ? page_fault_oops+0x2a8/0x3a0 [.] ? exc_page_fault+0x84/0x130 [.] ? asm_exc_page_fault+0x22/0x30 [.] ? ima_restore_measurement_list+0x95/0x4b0 [.] ? template_desc_init_fields+0x317/0x410 [.] ? crypto_alloc_tfm_node+0x9c/0xc0 [.] ? init_ima_lsm+0x30/0x30 [.] ima_load_kexec_buffer+0x72/0xa0 [.] ima_init+0x44/0xa0 [.] __initstub__kmod_ima__373_1201_init_ima7+0x1e/0xb0 [.] ? init_ima_lsm+0x30/0x30 [.] do_one_initcall+0xad/0x200 [.] ? idr_alloc_cyclic+0xaa/0x110 [.] ? new_slab+0x12c/0x420 [.] ? new_slab+0x12c/0x420 [.] ? number+0x12a/0x430 [.] ? sysvec_apic_timer_interrupt+0xa/0x80 [.] ? asm_sysvec_apic_timer_interrupt+0x16/0x20 [.] ? parse_args+0xd4/0x380 [.] ? parse_args+0x14b/0x380 [.] kernel_init_freeable+0x1c1/0x2b0 [.] ? rest_init+0xb0/0xb0 [.] kernel_init+0x16/0x1a0 [.] ret_from_fork+0x2f/0x40 [.] ? rest_init+0xb0/0xb0 [.] ret_from_fork_asm+0x11/0x20 [.] </TASK>

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci: fix null-ptr-deref in hci_read_supported_codecs Fix __hci_cmd_sync_sk() to return not NULL for unknown opcodes. __hci_cmd_sync_sk() returns NULL if a command returns a status event. However, it also returns NULL where an opcode doesn't exist in the hci_cc table because hci_cmd_complete_evt() assumes status = skb->data[0] for unknown opcodes. This leads to null-ptr-deref in cmd_sync for HCI_OP_READ_LOCAL_CODECS as there is no hci_cc for HCI_OP_READ_LOCAL_CODECS, which always assumes status = skb->data[0]. KASAN: null-ptr-deref in range [0x0000000000000070-0x0000000000000077] CPU: 1 PID: 2000 Comm: kworker/u9:5 Not tainted 6.9.0-ga6bcb805883c-dirty #10 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Workqueue: hci7 hci_power_on RIP: 0010:hci_read_supported_codecs+0xb9/0x870 net/bluetooth/hci_codec.c:138 Code: 08 48 89 ef e8 b8 c1 8f fd 48 8b 75 00 e9 96 00 00 00 49 89 c6 48 ba 00 00 00 00 00 fc ff df 4c 8d 60 70 4c 89 e3 48 c1 eb 03 <0f> b6 04 13 84 c0 0f 85 82 06 00 00 41 83 3c 24 02 77 0a e8 bf 78 RSP: 0018:ffff888120bafac8 EFLAGS: 00010212 RAX: 0000000000000000 RBX: 000000000000000e RCX: ffff8881173f0040 RDX: dffffc0000000000 RSI: ffffffffa58496c0 RDI: ffff88810b9ad1e4 RBP: ffff88810b9ac000 R08: ffffffffa77882a7 R09: 1ffffffff4ef1054 R10: dffffc0000000000 R11: fffffbfff4ef1055 R12: 0000000000000070 R13: 0000000000000000 R14: 0000000000000000 R15: ffff88810b9ac000 FS: 0000000000000000(0000) GS:ffff8881f6c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f6ddaa3439e CR3: 0000000139764003 CR4: 0000000000770ef0 PKRU: 55555554 Call Trace: <TASK> hci_read_local_codecs_sync net/bluetooth/hci_sync.c:4546 [inline] hci_init_stage_sync net/bluetooth/hci_sync.c:3441 [inline] hci_init4_sync net/bluetooth/hci_sync.c:4706 [inline] hci_init_sync net/bluetooth/hci_sync.c:4742 [inline] hci_dev_init_sync net/bluetooth/hci_sync.c:4912 [inline] hci_dev_open_sync+0x19a9/0x2d30 net/bluetooth/hci_sync.c:4994 hci_dev_do_open net/bluetooth/hci_core.c:483 [inline] hci_power_on+0x11e/0x560 net/bluetooth/hci_core.c:1015 process_one_work kernel/workqueue.c:3267 [inline] process_scheduled_works+0x8ef/0x14f0 kernel/workqueue.c:3348 worker_thread+0x91f/0xe50 kernel/workqueue.c:3429 kthread+0x2cb/0x360 kernel/kthread.c:388 ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244

In the Linux kernel, the following vulnerability has been resolved: bpf: Free dynamically allocated bits in bpf_iter_bits_destroy() bpf_iter_bits_destroy() uses "kit->nr_bits <= 64" to check whether the bits are dynamically allocated. However, the check is incorrect and may cause a kmemleak as shown below: unreferenced object 0xffff88812628c8c0 (size 32): comm "swapper/0", pid 1, jiffies 4294727320 hex dump (first 32 bytes): b0 c1 55 f5 81 88 ff ff f0 f0 f0 f0 f0 f0 f0 f0 ..U........... f0 f0 f0 f0 f0 f0 f0 f0 00 00 00 00 00 00 00 00 .............. backtrace (crc 781e32cc): [<00000000c452b4ab>] kmemleak_alloc+0x4b/0x80 [<0000000004e09f80>] __kmalloc_node_noprof+0x480/0x5c0 [<00000000597124d6>] __alloc.isra.0+0x89/0xb0 [<000000004ebfffcd>] alloc_bulk+0x2af/0x720 [<00000000d9c10145>] prefill_mem_cache+0x7f/0xb0 [<00000000ff9738ff>] bpf_mem_alloc_init+0x3e2/0x610 [<000000008b616eac>] bpf_global_ma_init+0x19/0x30 [<00000000fc473efc>] do_one_initcall+0xd3/0x3c0 [<00000000ec81498c>] kernel_init_freeable+0x66a/0x940 [<00000000b119f72f>] kernel_init+0x20/0x160 [<00000000f11ac9a7>] ret_from_fork+0x3c/0x70 [<0000000004671da4>] ret_from_fork_asm+0x1a/0x30 That is because nr_bits will be set as zero in bpf_iter_bits_next() after all bits have been iterated. Fix the issue by setting kit->bit to kit->nr_bits instead of setting kit->nr_bits to zero when the iteration completes in bpf_iter_bits_next(). In addition, use "!nr_bits || bits >= nr_bits" to check whether the iteration is complete and still use "nr_bits > 64" to indicate whether bits are dynamically allocated. The "!nr_bits" check is necessary because bpf_iter_bits_new() may fail before setting kit->nr_bits, and this condition will stop the iteration early instead of accessing the zeroed or freed kit->bits. Considering the initial value of kit->bits is -1 and the type of kit->nr_bits is unsigned int, change the type of kit->nr_bits to int. The potential overflow problem will be handled in the following patch.

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix kernel crash when uninstalling driver When the driver is uninstalled and the VF is disabled concurrently, a kernel crash occurs. The reason is that the two actions call function pci_disable_sriov(). The num_VFs is checked to determine whether to release the corresponding resources. During the second calling, num_VFs is not 0 and the resource release function is called. However, the corresponding resource has been released during the first invoking. Therefore, the problem occurs: [15277.839633][T50670] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000020 ... [15278.131557][T50670] Call trace: [15278.134686][T50670] klist_put+0x28/0x12c [15278.138682][T50670] klist_del+0x14/0x20 [15278.142592][T50670] device_del+0xbc/0x3c0 [15278.146676][T50670] pci_remove_bus_device+0x84/0x120 [15278.151714][T50670] pci_stop_and_remove_bus_device+0x6c/0x80 [15278.157447][T50670] pci_iov_remove_virtfn+0xb4/0x12c [15278.162485][T50670] sriov_disable+0x50/0x11c [15278.166829][T50670] pci_disable_sriov+0x24/0x30 [15278.171433][T50670] hnae3_unregister_ae_algo_prepare+0x60/0x90 [hnae3] [15278.178039][T50670] hclge_exit+0x28/0xd0 [hclge] [15278.182730][T50670] __se_sys_delete_module.isra.0+0x164/0x230 [15278.188550][T50670] __arm64_sys_delete_module+0x1c/0x30 [15278.193848][T50670] invoke_syscall+0x50/0x11c [15278.198278][T50670] el0_svc_common.constprop.0+0x158/0x164 [15278.203837][T50670] do_el0_svc+0x34/0xcc [15278.207834][T50670] el0_svc+0x20/0x30 For details, see the following figure. rmmod hclge disable VFs ---------------------------------------------------- hclge_exit() sriov_numvfs_store() ... device_lock() pci_disable_sriov() hns3_pci_sriov_configure() pci_disable_sriov() sriov_disable() sriov_disable() if !num_VFs : if !num_VFs : return; return; sriov_del_vfs() sriov_del_vfs() ... ... klist_put() klist_put() ... ... num_VFs = 0; num_VFs = 0; device_unlock(); In this patch, when driver is removing, we get the device_lock() to protect num_VFs, just like sriov_numvfs_store().

In the Linux kernel, the following vulnerability has been resolved: net: microchip: vcap api: Fix memory leaks in vcap_api_encode_rule_test() Commit a3c1e45156ad ("net: microchip: vcap: Fix use-after-free error in kunit test") fixed the use-after-free error, but introduced below memory leaks by removing necessary vcap_free_rule(), add it to fix it. unreferenced object 0xffffff80ca58b700 (size 192): comm "kunit_try_catch", pid 1215, jiffies 4294898264 hex dump (first 32 bytes): 00 12 7a 00 05 00 00 00 0a 00 00 00 64 00 00 00 ..z.........d... 00 00 00 00 00 00 00 00 00 04 0b cc 80 ff ff ff ................ backtrace (crc 9c09c3fe): [<0000000052a0be73>] kmemleak_alloc+0x34/0x40 [<0000000043605459>] __kmalloc_cache_noprof+0x26c/0x2f4 [<0000000040a01b8d>] vcap_alloc_rule+0x3cc/0x9c4 [<000000003fe86110>] vcap_api_encode_rule_test+0x1ac/0x16b0 [<00000000b3595fc4>] kunit_try_run_case+0x13c/0x3ac [<0000000010f5d2bf>] kunit_generic_run_threadfn_adapter+0x80/0xec [<00000000c5d82c9a>] kthread+0x2e8/0x374 [<00000000f4287308>] ret_from_fork+0x10/0x20 unreferenced object 0xffffff80cc0b0400 (size 64): comm "kunit_try_catch", pid 1215, jiffies 4294898265 hex dump (first 32 bytes): 80 04 0b cc 80 ff ff ff 18 b7 58 ca 80 ff ff ff ..........X..... 39 00 00 00 02 00 00 00 06 05 04 03 02 01 ff ff 9............... backtrace (crc daf014e9): [<0000000052a0be73>] kmemleak_alloc+0x34/0x40 [<0000000043605459>] __kmalloc_cache_noprof+0x26c/0x2f4 [<000000000ff63fd4>] vcap_rule_add_key+0x2cc/0x528 [<00000000dfdb1e81>] vcap_api_encode_rule_test+0x224/0x16b0 [<00000000b3595fc4>] kunit_try_run_case+0x13c/0x3ac [<0000000010f5d2bf>] kunit_generic_run_threadfn_adapter+0x80/0xec [<00000000c5d82c9a>] kthread+0x2e8/0x374 [<00000000f4287308>] ret_from_fork+0x10/0x20 unreferenced object 0xffffff80cc0b0700 (size 64): comm "kunit_try_catch", pid 1215, jiffies 4294898265 hex dump (first 32 bytes): 80 07 0b cc 80 ff ff ff 28 b7 58 ca 80 ff ff ff ........(.X..... 3c 00 00 00 00 00 00 00 01 2f 03 b3 ec ff ff ff <......../...... backtrace (crc 8d877792): [<0000000052a0be73>] kmemleak_alloc+0x34/0x40 [<0000000043605459>] __kmalloc_cache_noprof+0x26c/0x2f4 [<000000006eadfab7>] vcap_rule_add_action+0x2d0/0x52c [<00000000323475d1>] vcap_api_encode_rule_test+0x4d4/0x16b0 [<00000000b3595fc4>] kunit_try_run_case+0x13c/0x3ac [<0000000010f5d2bf>] kunit_generic_run_threadfn_adapter+0x80/0xec [<00000000c5d82c9a>] kthread+0x2e8/0x374 [<00000000f4287308>] ret_from_fork+0x10/0x20 unreferenced object 0xffffff80cc0b0900 (size 64): comm "kunit_try_catch", pid 1215, jiffies 4294898266 hex dump (first 32 bytes): 80 09 0b cc 80 ff ff ff 80 06 0b cc 80 ff ff ff ................ 7d 00 00 00 01 00 00 00 00 00 00 00 ff 00 00 00 }............... backtrace (crc 34181e56): [<0000000052a0be73>] kmemleak_alloc+0x34/0x40 [<0000000043605459>] __kmalloc_cache_noprof+0x26c/0x2f4 [<000000000ff63fd4>] vcap_rule_add_key+0x2cc/0x528 [<00000000991e3564>] vcap_val_rule+0xcf0/0x13e8 [<00000000fc9868e5>] vcap_api_encode_rule_test+0x678/0x16b0 [<00000000b3595fc4>] kunit_try_run_case+0x13c/0x3ac [<0000000010f5d2bf>] kunit_generic_run_threadfn_adapter+0x80/0xec [<00000000c5d82c9a>] kthread+0x2e8/0x374 [<00000000f4287308>] ret_from_fork+0x10/0x20 unreferenced object 0xffffff80cc0b0980 (size 64): comm "kunit_try_catch", pid 1215, jiffies 4294898266 hex dump (first 32 bytes): 18 b7 58 ca 80 ff ff ff 00 09 0b cc 80 ff ff ff ..X............. 67 00 00 00 00 00 00 00 01 01 74 88 c0 ff ff ff g.........t..... backtrace (crc 275fd9be): [<0000000052a0be73>] kmemleak_alloc+0x34/0x40 [<0000000043605459>] __kmalloc_cache_noprof+0x26c/0x2f4 [<000000000ff63fd4>] vcap_rule_add_key+0x2cc/0x528 [<000000001396a1a2>] test_add_de ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: ethernet: mtk_eth_soc: fix memory corruption during fq dma init The loop responsible for allocating up to MTK_FQ_DMA_LENGTH buffers must only touch as many descriptors, otherwise it ends up corrupting unrelated memory. Fix the loop iteration count accordingly.

In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_ipip: Fix memory leak when changing remote IPv6 address The device stores IPv6 addresses that are used for encapsulation in linear memory that is managed by the driver. Changing the remote address of an ip6gre net device never worked properly, but since cited commit the following reproducer [1] would result in a warning [2] and a memory leak [3]. The problem is that the new remote address is never added by the driver to its hash table (and therefore the device) and the old address is never removed from it. Fix by programming the new address when the configuration of the ip6gre net device changes and removing the old one. If the address did not change, then the above would result in increasing the reference count of the address and then decreasing it. [1] # ip link add name bla up type ip6gre local 2001:db8:1::1 remote 2001:db8:2::1 tos inherit ttl inherit # ip link set dev bla type ip6gre remote 2001:db8:3::1 # ip link del dev bla # devlink dev reload pci/0000:01:00.0 [2] WARNING: CPU: 0 PID: 1682 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3002 mlxsw_sp_ipv6_addr_put+0x140/0x1d0 Modules linked in: CPU: 0 UID: 0 PID: 1682 Comm: ip Not tainted 6.12.0-rc3-custom-g86b5b55bc835 #151 Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023 RIP: 0010:mlxsw_sp_ipv6_addr_put+0x140/0x1d0 [...] Call Trace: <TASK> mlxsw_sp_router_netdevice_event+0x55f/0x1240 notifier_call_chain+0x5a/0xd0 call_netdevice_notifiers_info+0x39/0x90 unregister_netdevice_many_notify+0x63e/0x9d0 rtnl_dellink+0x16b/0x3a0 rtnetlink_rcv_msg+0x142/0x3f0 netlink_rcv_skb+0x50/0x100 netlink_unicast+0x242/0x390 netlink_sendmsg+0x1de/0x420 ____sys_sendmsg+0x2bd/0x320 ___sys_sendmsg+0x9a/0xe0 __sys_sendmsg+0x7a/0xd0 do_syscall_64+0x9e/0x1a0 entry_SYSCALL_64_after_hwframe+0x77/0x7f [3] unreferenced object 0xffff898081f597a0 (size 32): comm "ip", pid 1626, jiffies 4294719324 hex dump (first 32 bytes): 20 01 0d b8 00 02 00 00 00 00 00 00 00 00 00 01 ............... 21 49 61 83 80 89 ff ff 00 00 00 00 01 00 00 00 !Ia............. backtrace (crc fd9be911): [<00000000df89c55d>] __kmalloc_cache_noprof+0x1da/0x260 [<00000000ff2a1ddb>] mlxsw_sp_ipv6_addr_kvdl_index_get+0x281/0x340 [<000000009ddd445d>] mlxsw_sp_router_netdevice_event+0x47b/0x1240 [<00000000743e7757>] notifier_call_chain+0x5a/0xd0 [<000000007c7b9e13>] call_netdevice_notifiers_info+0x39/0x90 [<000000002509645d>] register_netdevice+0x5f7/0x7a0 [<00000000c2e7d2a9>] ip6gre_newlink_common.isra.0+0x65/0x130 [<0000000087cd6d8d>] ip6gre_newlink+0x72/0x120 [<000000004df7c7cc>] rtnl_newlink+0x471/0xa20 [<0000000057ed632a>] rtnetlink_rcv_msg+0x142/0x3f0 [<0000000032e0d5b5>] netlink_rcv_skb+0x50/0x100 [<00000000908bca63>] netlink_unicast+0x242/0x390 [<00000000cdbe1c87>] netlink_sendmsg+0x1de/0x420 [<0000000011db153e>] ____sys_sendmsg+0x2bd/0x320 [<000000003b6d53eb>] ___sys_sendmsg+0x9a/0xe0 [<00000000cae27c62>] __sys_sendmsg+0x7a/0xd0

In the Linux kernel, the following vulnerability has been resolved: fsl/fman: Fix refcount handling of fman-related devices In mac_probe() there are multiple calls to of_find_device_by_node(), fman_bind() and fman_port_bind() which takes references to of_dev->dev. Not all references taken by these calls are released later on error path in mac_probe() and in mac_remove() which lead to reference leaks. Add references release.

In the Linux kernel, the following vulnerability has been resolved: RDMA/bnxt_re: Avoid CPU lockups due fifo occupancy check loop Driver waits indefinitely for the fifo occupancy to go below a threshold as soon as the pacing interrupt is received. This can cause soft lockup on one of the processors, if the rate of DB is very high. Add a loop count for FPGA and exit the __wait_for_fifo_occupancy_below_th if the loop is taking more time. Pacing will be continuing until the occupancy is below the threshold. This is ensured by the checks in bnxt_re_pacing_timer_exp and further scheduling the work for pacing based on the fifo occupancy.

In the Linux kernel, the following vulnerability has been resolved: maple_tree: correct tree corruption on spanning store Patch series "maple_tree: correct tree corruption on spanning store", v3. There has been a nasty yet subtle maple tree corruption bug that appears to have been in existence since the inception of the algorithm. This bug seems far more likely to happen since commit f8d112a4e657 ("mm/mmap: avoid zeroing vma tree in mmap_region()"), which is the point at which reports started to be submitted concerning this bug. We were made definitely aware of the bug thanks to the kind efforts of Bert Karwatzki who helped enormously in my being able to track this down and identify the cause of it. The bug arises when an attempt is made to perform a spanning store across two leaf nodes, where the right leaf node is the rightmost child of the shared parent, AND the store completely consumes the right-mode node. This results in mas_wr_spanning_store() mitakenly duplicating the new and existing entries at the maximum pivot within the range, and thus maple tree corruption. The fix patch corrects this by detecting this scenario and disallowing the mistaken duplicate copy. The fix patch commit message goes into great detail as to how this occurs. This series also includes a test which reliably reproduces the issue, and asserts that the fix works correctly. Bert has kindly tested the fix and confirmed it resolved his issues. Also Mikhail Gavrilov kindly reported what appears to be precisely the same bug, which this fix should also resolve. This patch (of 2): There has been a subtle bug present in the maple tree implementation from its inception. This arises from how stores are performed - when a store occurs, it will overwrite overlapping ranges and adjust the tree as necessary to accommodate this. A range may always ultimately span two leaf nodes. In this instance we walk the two leaf nodes, determine which elements are not overwritten to the left and to the right of the start and end of the ranges respectively and then rebalance the tree to contain these entries and the newly inserted one. This kind of store is dubbed a 'spanning store' and is implemented by mas_wr_spanning_store(). In order to reach this stage, mas_store_gfp() invokes mas_wr_preallocate(), mas_wr_store_type() and mas_wr_walk() in turn to walk the tree and update the object (mas) to traverse to the location where the write should be performed, determining its store type. When a spanning store is required, this function returns false stopping at the parent node which contains the target range, and mas_wr_store_type() marks the mas->store_type as wr_spanning_store to denote this fact. When we go to perform the store in mas_wr_spanning_store(), we first determine the elements AFTER the END of the range we wish to store (that is, to the right of the entry to be inserted) - we do this by walking to the NEXT pivot in the tree (i.e. r_mas.last + 1), starting at the node we have just determined contains the range over which we intend to write. We then turn our attention to the entries to the left of the entry we are inserting, whose state is represented by l_mas, and copy these into a 'big node', which is a special node which contains enough slots to contain two leaf node's worth of data. We then copy the entry we wish to store immediately after this - the copy and the insertion of the new entry is performed by mas_store_b_node(). After this we copy the elements to the right of the end of the range which we are inserting, if we have not exceeded the length of the node (i.e. r_mas.offset <= r_mas.end). Herein lies the bug - under very specific circumstances, this logic can break and corrupt the maple tree. Consider the following tree: Height 0 Root Node / \ pivot = 0xffff / \ pivot = ULONG_MAX / ---truncated---

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix possible double free in smb2_set_ea() Clang static checker(scan-build) warning： fs/smb/client/smb2ops.c:1304:2: Attempt to free released memory. 1304 | kfree(ea); | ^~~~~~~~~ There is a double free in such case: 'ea is initialized to NULL' -> 'first successful memory allocation for ea' -> 'something failed, goto sea_exit' -> 'first memory release for ea' -> 'goto replay_again' -> 'second goto sea_exit before allocate memory for ea' -> 'second memory release for ea resulted in double free'. Re-initialie 'ea' to NULL near to the replay_again label, it can fix this double free problem.

In the Linux kernel, the following vulnerability has been resolved: drm/panthor: Fix access to uninitialized variable in tick_ctx_cleanup() The group variable can't be used to retrieve ptdev in our second loop, because it points to the previously iterated list_head, not a valid group. Get the ptdev object from the scheduler instead.

In the Linux kernel, the following vulnerability has been resolved: media: v4l2-tpg: prevent the risk of a division by zero As reported by Coverity, the logic at tpg_precalculate_line() blindly rescales the buffer even when scaled_witdh is equal to zero. If this ever happens, this will cause a division by zero. Instead, add a WARN_ON_ONCE() to trigger such cases and return without doing any precalculation.

In the Linux kernel, the following vulnerability has been resolved: binfmt_elf_fdpic: fix AUXV size calculation when ELF_HWCAP2 is defined create_elf_fdpic_tables() does not correctly account the space for the AUX vector when an architecture has ELF_HWCAP2 defined. Prior to the commit 10e29251be0e ("binfmt_elf_fdpic: fix /proc/<pid>/auxv") it resulted in the last entry of the AUX vector being set to zero, but with that change it results in a kernel BUG. Fix that by adding one to the number of AUXV entries (nitems) when ELF_HWCAP2 is defined.

In the Linux kernel, the following vulnerability has been resolved: netfilter: br_netfilter: fix panic with metadata_dst skb Fix a kernel panic in the br_netfilter module when sending untagged traffic via a VxLAN device. This happens during the check for fragmentation in br_nf_dev_queue_xmit. It is dependent on: 1) the br_netfilter module being loaded; 2) net.bridge.bridge-nf-call-iptables set to 1; 3) a bridge with a VxLAN (single-vxlan-device) netdevice as a bridge port; 4) untagged frames with size higher than the VxLAN MTU forwarded/flooded When forwarding the untagged packet to the VxLAN bridge port, before the netfilter hooks are called, br_handle_egress_vlan_tunnel is called and changes the skb_dst to the tunnel dst. The tunnel_dst is a metadata type of dst, i.e., skb_valid_dst(skb) is false, and metadata->dst.dev is NULL. Then in the br_netfilter hooks, in br_nf_dev_queue_xmit, there's a check for frames that needs to be fragmented: frames with higher MTU than the VxLAN device end up calling br_nf_ip_fragment, which in turns call ip_skb_dst_mtu. The ip_dst_mtu tries to use the skb_dst(skb) as if it was a valid dst with valid dst->dev, thus the crash. This case was never supported in the first place, so drop the packet instead. PING 10.0.0.2 (10.0.0.2) from 0.0.0.0 h1-eth0: 2000(2028) bytes of data. [ 176.291791] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000110 [ 176.292101] Mem abort info: [ 176.292184] ESR = 0x0000000096000004 [ 176.292322] EC = 0x25: DABT (current EL), IL = 32 bits [ 176.292530] SET = 0, FnV = 0 [ 176.292709] EA = 0, S1PTW = 0 [ 176.292862] FSC = 0x04: level 0 translation fault [ 176.293013] Data abort info: [ 176.293104] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000 [ 176.293488] CM = 0, WnR = 0, TnD = 0, TagAccess = 0 [ 176.293787] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 [ 176.293995] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000043ef5000 [ 176.294166] [0000000000000110] pgd=0000000000000000, p4d=0000000000000000 [ 176.294827] Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP [ 176.295252] Modules linked in: vxlan ip6_udp_tunnel udp_tunnel veth br_netfilter bridge stp llc ipv6 crct10dif_ce [ 176.295923] CPU: 0 PID: 188 Comm: ping Not tainted 6.8.0-rc3-g5b3fbd61b9d1 #2 [ 176.296314] Hardware name: linux,dummy-virt (DT) [ 176.296535] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 176.296808] pc : br_nf_dev_queue_xmit+0x390/0x4ec [br_netfilter] [ 176.297382] lr : br_nf_dev_queue_xmit+0x2ac/0x4ec [br_netfilter] [ 176.297636] sp : ffff800080003630 [ 176.297743] x29: ffff800080003630 x28: 0000000000000008 x27: ffff6828c49ad9f8 [ 176.298093] x26: ffff6828c49ad000 x25: 0000000000000000 x24: 00000000000003e8 [ 176.298430] x23: 0000000000000000 x22: ffff6828c4960b40 x21: ffff6828c3b16d28 [ 176.298652] x20: ffff6828c3167048 x19: ffff6828c3b16d00 x18: 0000000000000014 [ 176.298926] x17: ffffb0476322f000 x16: ffffb7e164023730 x15: 0000000095744632 [ 176.299296] x14: ffff6828c3f1c880 x13: 0000000000000002 x12: ffffb7e137926a70 [ 176.299574] x11: 0000000000000001 x10: ffff6828c3f1c898 x9 : 0000000000000000 [ 176.300049] x8 : ffff6828c49bf070 x7 : 0008460f18d5f20e x6 : f20e0100bebafeca [ 176.300302] x5 : ffff6828c7f918fe x4 : ffff6828c49bf070 x3 : 0000000000000000 [ 176.300586] x2 : 0000000000000000 x1 : ffff6828c3c7ad00 x0 : ffff6828c7f918f0 [ 176.300889] Call trace: [ 176.301123] br_nf_dev_queue_xmit+0x390/0x4ec [br_netfilter] [ 176.301411] br_nf_post_routing+0x2a8/0x3e4 [br_netfilter] [ 176.301703] nf_hook_slow+0x48/0x124 [ 176.302060] br_forward_finish+0xc8/0xe8 [bridge] [ 176.302371] br_nf_hook_thresh+0x124/0x134 [br_netfilter] [ 176.302605] br_nf_forward_finish+0x118/0x22c [br_netfilter] [ 176.302824] br_nf_forward_ip.part.0+0x264/0x290 [br_netfilter] [ 176.303136] br_nf_forward+0x2b8/0x4e0 [br_netfilter] [ 176.303359] nf_hook_slow+0x48/0x124 [ 176.303 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: mm/swapfile: skip HugeTLB pages for unuse_vma I got a bad pud error and lost a 1GB HugeTLB when calling swapoff. The problem can be reproduced by the following steps: 1. Allocate an anonymous 1GB HugeTLB and some other anonymous memory. 2. Swapout the above anonymous memory. 3. run swapoff and we will get a bad pud error in kernel message: mm/pgtable-generic.c:42: bad pud 00000000743d215d(84000001400000e7) We can tell that pud_clear_bad is called by pud_none_or_clear_bad in unuse_pud_range() by ftrace. And therefore the HugeTLB pages will never be freed because we lost it from page table. We can skip HugeTLB pages for unuse_vma to fix it.

In the Linux kernel, the following vulnerability has been resolved: xfs: fix finding a last resort AG in xfs_filestream_pick_ag When the main loop in xfs_filestream_pick_ag fails to find a suitable AG it tries to just pick the online AG. But the loop for that uses args->pag as loop iterator while the later code expects pag to be set. Fix this by reusing the max_pag case for this last resort, and also add a check for impossible case of no AG just to make sure that the uninitialized pag doesn't even escape in theory.

In the Linux kernel, the following vulnerability has been resolved: ceph: remove the incorrect Fw reference check when dirtying pages When doing the direct-io reads it will also try to mark pages dirty, but for the read path it won't hold the Fw caps and there is case will it get the Fw reference.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs-srv: Avoid null pointer deref during path establishment For RTRS path establishment, RTRS client initiates and completes con_num of connections. After establishing all its connections, the information is exchanged between the client and server through the info_req message. During this exchange, it is essential that all connections have been established, and the state of the RTRS srv path is CONNECTED. So add these sanity checks, to make sure we detect and abort process in error scenarios to avoid null pointer deref.

In the Linux kernel, the following vulnerability has been resolved: media: qcom: camss: Remove use_count guard in stop_streaming The use_count check was introduced so that multiple concurrent Raw Data Interfaces RDIs could be driven by different virtual channels VCs on the CSIPHY input driving the video pipeline. This is an invalid use of use_count though as use_count pertains to the number of times a video entity has been opened by user-space not the number of active streams. If use_count and stream-on count don't agree then stop_streaming() will break as is currently the case and has become apparent when using CAMSS with libcamera's released softisp 0.3. The use of use_count like this is a bit hacky and right now breaks regular usage of CAMSS for a single stream case. Stopping qcam results in the splat below, and then it cannot be started again and any attempts to do so fails with -EBUSY. [ 1265.509831] WARNING: CPU: 5 PID: 919 at drivers/media/common/videobuf2/videobuf2-core.c:2183 __vb2_queue_cancel+0x230/0x2c8 [videobuf2_common] ... [ 1265.510630] Call trace: [ 1265.510636] __vb2_queue_cancel+0x230/0x2c8 [videobuf2_common] [ 1265.510648] vb2_core_streamoff+0x24/0xcc [videobuf2_common] [ 1265.510660] vb2_ioctl_streamoff+0x5c/0xa8 [videobuf2_v4l2] [ 1265.510673] v4l_streamoff+0x24/0x30 [videodev] [ 1265.510707] __video_do_ioctl+0x190/0x3f4 [videodev] [ 1265.510732] video_usercopy+0x304/0x8c4 [videodev] [ 1265.510757] video_ioctl2+0x18/0x34 [videodev] [ 1265.510782] v4l2_ioctl+0x40/0x60 [videodev] ... [ 1265.510944] videobuf2_common: driver bug: stop_streaming operation is leaving buffer 0 in active state [ 1265.511175] videobuf2_common: driver bug: stop_streaming operation is leaving buffer 1 in active state [ 1265.511398] videobuf2_common: driver bug: stop_streaming operation is leaving buffer 2 in active st One CAMSS specific way to handle multiple VCs on the same RDI might be: - Reference count each pipeline enable for CSIPHY, CSID, VFE and RDIx. - The video buffers are already associated with msm_vfeN_rdiX so release video buffers when told to do so by stop_streaming. - Only release the power-domains for the CSIPHY, CSID and VFE when their internal refcounts drop. Either way refusing to release video buffers based on use_count is erroneous and should be reverted. The silicon enabling code for selecting VCs is perfectly fine. Its a "known missing feature" that concurrent VCs won't work with CAMSS right now. Initial testing with this code didn't show an error but, SoftISP and "real" usage with Google Hangouts breaks the upstream code pretty quickly, we need to do a partial revert and take another pass at VCs. This commit partially reverts commit 89013969e232 ("media: camss: sm8250: Pipeline starting and stopping for multiple virtual channels")

In the Linux kernel, the following vulnerability has been resolved: posix-clock: Fix missing timespec64 check in pc_clock_settime() As Andrew pointed out, it will make sense that the PTP core checked timespec64 struct's tv_sec and tv_nsec range before calling ptp->info->settime64(). As the man manual of clock_settime() said, if tp.tv_sec is negative or tp.tv_nsec is outside the range [0..999,999,999], it should return EINVAL, which include dynamic clocks which handles PTP clock, and the condition is consistent with timespec64_valid(). As Thomas suggested, timespec64_valid() only check the timespec is valid, but not ensure that the time is in a valid range, so check it ahead using timespec64_valid_strict() in pc_clock_settime() and return -EINVAL if not valid. There are some drivers that use tp->tv_sec and tp->tv_nsec directly to write registers without validity checks and assume that the higher layer has checked it, which is dangerous and will benefit from this, such as hclge_ptp_settime(), igb_ptp_settime_i210(), _rcar_gen4_ptp_settime(), and some drivers can remove the checks of itself.

In the Linux kernel, the following vulnerability has been resolved: sfc: Don't invoke xdp_do_flush() from netpoll. Yury reported a crash in the sfc driver originated from netpoll_send_udp(). The netconsole sends a message and then netpoll invokes the driver's NAPI function with a budget of zero. It is dedicated to allow driver to free TX resources, that it may have used while sending the packet. In the netpoll case the driver invokes xdp_do_flush() unconditionally, leading to crash because bpf_net_context was never assigned. Invoke xdp_do_flush() only if budget is not zero.

In the Linux kernel, the following vulnerability has been resolved: ice: fix memleak in ice_init_tx_topology() Fix leak of the FW blob (DDP pkg). Make ice_cfg_tx_topo() const-correct, so ice_init_tx_topology() can avoid copying whole FW blob. Copy just the topology section, and only when needed. Reuse the buffer allocated for the read of the current topology. This was found by kmemleak, with the following trace for each PF: [<ffffffff8761044d>] kmemdup_noprof+0x1d/0x50 [<ffffffffc0a0a480>] ice_init_ddp_config+0x100/0x220 [ice] [<ffffffffc0a0da7f>] ice_init_dev+0x6f/0x200 [ice] [<ffffffffc0a0dc49>] ice_init+0x29/0x560 [ice] [<ffffffffc0a10c1d>] ice_probe+0x21d/0x310 [ice] Constify ice_cfg_tx_topo() @buf parameter. This cascades further down to few more functions.