In the Linux kernel, the following vulnerability has been resolved: team: fix null-ptr-deref when team device type is changed Get a null-ptr-deref bug as follows with reproducer [1]. BUG: kernel NULL pointer dereference, address: 0000000000000228 ... RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q] ... Call Trace: <TASK> ? __die+0x24/0x70 ? page_fault_oops+0x82/0x150 ? exc_page_fault+0x69/0x150 ? asm_exc_page_fault+0x26/0x30 ? vlan_dev_hard_header+0x35/0x140 [8021q] ? vlan_dev_hard_header+0x8e/0x140 [8021q] neigh_connected_output+0xb2/0x100 ip6_finish_output2+0x1cb/0x520 ? nf_hook_slow+0x43/0xc0 ? ip6_mtu+0x46/0x80 ip6_finish_output+0x2a/0xb0 mld_sendpack+0x18f/0x250 mld_ifc_work+0x39/0x160 process_one_work+0x1e6/0x3f0 worker_thread+0x4d/0x2f0 ? __pfx_worker_thread+0x10/0x10 kthread+0xe5/0x120 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x34/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 [1] $ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}' $ ip link add name t-dummy type dummy $ ip link add link t-dummy name t-dummy.100 type vlan id 100 $ ip link add name t-nlmon type nlmon $ ip link set t-nlmon master team0 $ ip link set t-nlmon nomaster $ ip link set t-dummy up $ ip link set team0 up $ ip link set t-dummy.100 down $ ip link set t-dummy.100 master team0 When enslave a vlan device to team device and team device type is changed from non-ether to ether, header_ops of team device is changed to vlan_header_ops. That is incorrect and will trigger null-ptr-deref for vlan->real_dev in vlan_dev_hard_header() because team device is not a vlan device. Cache eth_header_ops in team_setup(), then assign cached header_ops to header_ops of team net device when its type is changed from non-ether to ether to fix the bug.

In the Linux kernel, the following vulnerability has been resolved: net: fix possible store tearing in neigh_periodic_work() While looking at a related syzbot report involving neigh_periodic_work(), I found that I forgot to add an annotation when deleting an RCU protected item from a list. Readers use rcu_deference(*np), we need to use either rcu_assign_pointer() or WRITE_ONCE() on writer side to prevent store tearing. I use rcu_assign_pointer() to have lockdep support, this was the choice made in neigh_flush_dev().

In the Linux kernel, the following vulnerability has been resolved: aio: fix mremap after fork null-deref Commit e4a0d3e720e7 ("aio: Make it possible to remap aio ring") introduced a null-deref if mremap is called on an old aio mapping after fork as mm->ioctx_table will be set to NULL. [jmoyer@redhat.com: fix 80 column issue]

In the Linux kernel, the following vulnerability has been resolved: drm/tegra: dsi: Add missing check for of_find_device_by_node Add check for the return value of of_find_device_by_node() and return the error if it fails in order to avoid NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Add NULL ptr dereference checking at the end of attr_allocate_frame() It is preferable to exit through the out: label because internal debugging functions are located there.

In the Linux kernel, the following vulnerability has been resolved: powerpc/lib: Validate size for vector operations Some of the fp/vmx code in sstep.c assume a certain maximum size for the instructions being emulated. The size of those operations however is determined separately in analyse_instr(). Add a check to validate the assumption on the maximum size of the operations, so as to prevent any unintended kernel stack corruption.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Fix lock dependency warning with srcu ====================================================== WARNING: possible circular locking dependency detected 6.5.0-kfd-yangp #2289 Not tainted ------------------------------------------------------ kworker/0:2/996 is trying to acquire lock: (srcu){.+.+}-{0:0}, at: __synchronize_srcu+0x5/0x1a0 but task is already holding lock: ((work_completion)(&svms->deferred_list_work)){+.+.}-{0:0}, at: process_one_work+0x211/0x560 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 ((work_completion)(&svms->deferred_list_work)){+.+.}-{0:0}: __flush_work+0x88/0x4f0 svm_range_list_lock_and_flush_work+0x3d/0x110 [amdgpu] svm_range_set_attr+0xd6/0x14c0 [amdgpu] kfd_ioctl+0x1d1/0x630 [amdgpu] __x64_sys_ioctl+0x88/0xc0 -> #2 (&info->lock#2){+.+.}-{3:3}: __mutex_lock+0x99/0xc70 amdgpu_amdkfd_gpuvm_restore_process_bos+0x54/0x740 [amdgpu] restore_process_helper+0x22/0x80 [amdgpu] restore_process_worker+0x2d/0xa0 [amdgpu] process_one_work+0x29b/0x560 worker_thread+0x3d/0x3d0 -> #1 ((work_completion)(&(&process->restore_work)->work)){+.+.}-{0:0}: __flush_work+0x88/0x4f0 __cancel_work_timer+0x12c/0x1c0 kfd_process_notifier_release_internal+0x37/0x1f0 [amdgpu] __mmu_notifier_release+0xad/0x240 exit_mmap+0x6a/0x3a0 mmput+0x6a/0x120 do_exit+0x322/0xb90 do_group_exit+0x37/0xa0 __x64_sys_exit_group+0x18/0x20 do_syscall_64+0x38/0x80 -> #0 (srcu){.+.+}-{0:0}: __lock_acquire+0x1521/0x2510 lock_sync+0x5f/0x90 __synchronize_srcu+0x4f/0x1a0 __mmu_notifier_release+0x128/0x240 exit_mmap+0x6a/0x3a0 mmput+0x6a/0x120 svm_range_deferred_list_work+0x19f/0x350 [amdgpu] process_one_work+0x29b/0x560 worker_thread+0x3d/0x3d0 other info that might help us debug this: Chain exists of: srcu --> &info->lock#2 --> (work_completion)(&svms->deferred_list_work) Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock((work_completion)(&svms->deferred_list_work)); lock(&info->lock#2); lock((work_completion)(&svms->deferred_list_work)); sync(srcu);

In the Linux kernel, the following vulnerability has been resolved: mmc: mmc_spi: fix error handling in mmc_spi_probe() If mmc_add_host() fails, it doesn't need to call mmc_remove_host(), or it will cause null-ptr-deref, because of deleting a not added device in mmc_remove_host(). To fix this, goto label 'fail_glue_init', if mmc_add_host() fails, and change the label 'fail_add_host' to 'fail_gpiod_request'.

In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: fix lock ordering in btrfs_zone_activate() The btrfs CI reported a lockdep warning as follows by running generic generic/129. WARNING: possible circular locking dependency detected 6.7.0-rc5+ #1 Not tainted ------------------------------------------------------ kworker/u5:5/793427 is trying to acquire lock: ffff88813256d028 (&cache->lock){+.+.}-{2:2}, at: btrfs_zone_finish_one_bg+0x5e/0x130 but task is already holding lock: ffff88810a23a318 (&fs_info->zone_active_bgs_lock){+.+.}-{2:2}, at: btrfs_zone_finish_one_bg+0x34/0x130 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&fs_info->zone_active_bgs_lock){+.+.}-{2:2}: ... -> #0 (&cache->lock){+.+.}-{2:2}: ... This is because we take fs_info->zone_active_bgs_lock after a block_group's lock in btrfs_zone_activate() while doing the opposite in other places. Fix the issue by expanding the fs_info->zone_active_bgs_lock's critical section and taking it before a block_group's lock.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Fix an NULL dereference bug The issue here is when this is called from ntfs_load_attr_list(). The "size" comes from le32_to_cpu(attr->res.data_size) so it can't overflow on a 64bit systems but on 32bit systems the "+ 1023" can overflow and the result is zero. This means that the kmalloc will succeed by returning the ZERO_SIZE_PTR and then the memcpy() will crash with an Oops on the next line.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: Drop chan lock before queuing buffers Ensure read and write locks for the channel are not taken in succession by dropping the read lock from parse_xfer_event() such that a callback given to client can potentially queue buffers and acquire the write lock in that process. Any queueing of buffers should be done without channel read lock acquired as it can result in multiple locks and a soft lockup. [mani: added fixes tag and cc'ed stable]

In the Linux kernel, the following vulnerability has been resolved: net: openvswitch: fix possible memory leak in ovs_meter_cmd_set() old_meter needs to be free after it is detached regardless of whether the new meter is successfully attached.

In the Linux kernel, the following vulnerability has been resolved: serial: sc16is7xx: convert from _raw_ to _noinc_ regmap functions for FIFO The SC16IS7XX IC supports a burst mode to access the FIFOs where the initial register address is sent ($00), followed by all the FIFO data without having to resend the register address each time. In this mode, the IC doesn't increment the register address for each R/W byte. The regmap_raw_read() and regmap_raw_write() are functions which can perform IO over multiple registers. They are currently used to read/write from/to the FIFO, and although they operate correctly in this burst mode on the SPI bus, they would corrupt the regmap cache if it was not disabled manually. The reason is that when the R/W size is more than 1 byte, these functions assume that the register address is incremented and handle the cache accordingly. Convert FIFO R/W functions to use the regmap _noinc_ versions in order to remove the manual cache control which was a workaround when using the _raw_ versions. FIFO registers are properly declared as volatile so cache will not be used/updated for FIFO accesses.

In the Linux kernel, the following vulnerability has been resolved: ALSA: scarlett2: Add missing error checks to *_ctl_get() The *_ctl_get() functions which call scarlett2_update_*() were not checking the return value. Fix to check the return value and pass to the caller.

In the Linux kernel, the following vulnerability has been resolved: thermal: core: Fix NULL pointer dereference in zone registration error path If device_register() in thermal_zone_device_register_with_trips() returns an error, the tz variable is set to NULL and subsequently dereferenced in kfree(tz->tzp). Commit adc8749b150c ("thermal/drivers/core: Use put_device() if device_register() fails") added the tz = NULL assignment in question to avoid a possible double-free after dropping the reference to the zone device. However, after commit 4649620d9404 ("thermal: core: Make thermal_zone_device_unregister() return after freeing the zone"), that assignment has become redundant, because dropping the reference to the zone device does not cause the zone object to be freed any more. Drop it to address the NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: net: rds: Fix possible NULL-pointer dereference In rds_rdma_cm_event_handler_cmn() check, if conn pointer exists before dereferencing it as rdma_set_service_type() argument Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: ALSA: scarlett2: Add clamp() in scarlett2_mixer_ctl_put() Ensure the value passed to scarlett2_mixer_ctl_put() is between 0 and SCARLETT2_MIXER_MAX_VALUE so we don't attempt to access outside scarlett2_mixer_values[].

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: sdio: Honor the host max_req_size in the RX path Lukas reports skb_over_panic errors on his Banana Pi BPI-CM4 which comes with an Amlogic A311D (G12B) SoC and a RTL8822CS SDIO wifi/Bluetooth combo card. The error he observed is identical to what has been fixed in commit e967229ead0e ("wifi: rtw88: sdio: Check the HISR RX_REQUEST bit in rtw_sdio_rx_isr()") but that commit didn't fix Lukas' problem. Lukas found that disabling or limiting RX aggregation works around the problem for some time (but does not fully fix it). In the following discussion a few key topics have been discussed which have an impact on this problem: - The Amlogic A311D (G12B) SoC has a hardware bug in the SDIO controller which prevents DMA transfers. Instead all transfers need to go through the controller SRAM which limits transfers to 1536 bytes - rtw88 chips don't split incoming (RX) packets, so if a big packet is received this is forwarded to the host in it's original form - rtw88 chips can do RX aggregation, meaning more multiple incoming packets can be pulled by the host from the card with one MMC/SDIO transfer. This Depends on settings in the REG_RXDMA_AGG_PG_TH register (BIT_RXDMA_AGG_PG_TH limits the number of packets that will be aggregated, BIT_DMA_AGG_TO_V1 configures a timeout for aggregation and BIT_EN_PRE_CALC makes the chip honor the limits more effectively) Use multiple consecutive reads in rtw_sdio_read_port() and limit the number of bytes which are copied by the host from the card in one MMC/SDIO transfer. This allows receiving a buffer that's larger than the hosts max_req_size (number of bytes which can be transferred in one MMC/SDIO transfer). As a result of this the skb_over_panic error is gone as the rtw88 driver is now able to receive more than 1536 bytes from the card (either because the incoming packet is larger than that or because multiple packets have been aggregated). In case of an receive errors (-EILSEQ has been observed by Lukas) we need to drain the remaining data from the card's buffer, otherwise the card will return corrupt data for the next rtw_sdio_read_port() call.

In the Linux kernel, the following vulnerability has been resolved: block: add check that partition length needs to be aligned with block size Before calling add partition or resize partition, there is no check on whether the length is aligned with the logical block size. If the logical block size of the disk is larger than 512 bytes, then the partition size maybe not the multiple of the logical block size, and when the last sector is read, bio_truncate() will adjust the bio size, resulting in an IO error if the size of the read command is smaller than the logical block size.If integrity data is supported, this will also result in a null pointer dereference when calling bio_integrity_free.

In the Linux kernel, the following vulnerability has been resolved: drm/tegra: rgb: Fix missing clk_put() in the error handling paths of tegra_dc_rgb_probe() If clk_get_sys(..., "pll_d2_out0") fails, the clk_get_sys() call must be undone. Add the missing clk_put and a new 'put_pll_d_out0' label in the error handling path, and use it.

In the Linux kernel, the following vulnerability has been resolved: media: v4l: async: Fix duplicated list deletion The list deletion call dropped here is already called from the helper function in the line before. Having a second list_del() call results in either a warning (with CONFIG_DEBUG_LIST=y): list_del corruption, c46c8198->next is LIST_POISON1 (00000100) If CONFIG_DEBUG_LIST is disabled the operation results in a kernel error due to NULL pointer dereference.

A flaw was found in KVM. An improper check in svm_set_x2apic_msr_interception() may allow direct access to host x2apic msrs when the guest resets its apic, potentially leading to a denial of service condition.

The handle_stop_signal function in signal.c in Linux kernel 2.6.11 up to other versions before 2.6.13 and 2.6.12.6 allows local users to cause a denial of service (deadlock) by sending a SIGKILL to a real-time threaded process while it is performing a core dump.

In the Linux kernel before 4.20.14, expand_downwards in mm/mmap.c lacks a check for the mmap minimum address, which makes it easier for attackers to exploit kernel NULL pointer dereferences on non-SMAP platforms. This is related to a capability check for the wrong task.

Array index overflow in the xfrm_sk_policy_insert function in xfrm_user.c in Linux kernel 2.6 allows local users to cause a denial of service (oops or deadlock) and possibly execute arbitrary code via a p->dir value that is larger than XFRM_POLICY_OUT, which is used as an index in the sock->sk_policy array.

drivers/scsi/bfa/bfa_core.c in the Linux kernel before 2.6.35 does not initialize a certain port data structure, which allows local users to cause a denial of service (system crash) via read operations on an fc_host statistics file.

In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel: Limit the period on Haswell Running the ltp test cve-2015-3290 concurrently reports the following warnings. perfevents: irq loop stuck! WARNING: CPU: 31 PID: 32438 at arch/x86/events/intel/core.c:3174 intel_pmu_handle_irq+0x285/0x370 Call Trace: <NMI> ? __warn+0xa4/0x220 ? intel_pmu_handle_irq+0x285/0x370 ? __report_bug+0x123/0x130 ? intel_pmu_handle_irq+0x285/0x370 ? __report_bug+0x123/0x130 ? intel_pmu_handle_irq+0x285/0x370 ? report_bug+0x3e/0xa0 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x18/0x50 ? asm_exc_invalid_op+0x1a/0x20 ? irq_work_claim+0x1e/0x40 ? intel_pmu_handle_irq+0x285/0x370 perf_event_nmi_handler+0x3d/0x60 nmi_handle+0x104/0x330 Thanks to Thomas Gleixner's analysis, the issue is caused by the low initial period (1) of the frequency estimation algorithm, which triggers the defects of the HW, specifically erratum HSW11 and HSW143. (For the details, please refer https://lore.kernel.org/lkml/87plq9l5d2.ffs@tglx/) The HSW11 requires a period larger than 100 for the INST_RETIRED.ALL event, but the initial period in the freq mode is 1. The erratum is the same as the BDM11, which has been supported in the kernel. A minimum period of 128 is enforced as well on HSW. HSW143 is regarding that the fixed counter 1 may overcount 32 with the Hyper-Threading is enabled. However, based on the test, the hardware has more issues than it tells. Besides the fixed counter 1, the message 'interrupt took too long' can be observed on any counter which was armed with a period < 32 and two events expired in the same NMI. A minimum period of 32 is enforced for the rest of the events. The recommended workaround code of the HSW143 is not implemented. Because it only addresses the issue for the fixed counter. It brings extra overhead through extra MSR writing. No related overcounting issue has been reported so far.

In the Linux kernel, the following vulnerability has been resolved: nvme-multipath: defer partition scanning We need to suppress the partition scan from occuring within the controller's scan_work context. If a path error occurs here, the IO will wait until a path becomes available or all paths are torn down, but that action also occurs within scan_work, so it would deadlock. Defer the partion scan to a different context that does not block scan_work.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Prevent deadlock while disabling aRFS When disabling aRFS under the `priv->state_lock`, any scheduled aRFS works are canceled using the `cancel_work_sync` function, which waits for the work to end if it has already started. However, while waiting for the work handler, the handler will try to acquire the `state_lock` which is already acquired. The worker acquires the lock to delete the rules if the state is down, which is not the worker's responsibility since disabling aRFS deletes the rules. Add an aRFS state variable, which indicates whether the aRFS is enabled and prevent adding rules when the aRFS is disabled. Kernel log: ====================================================== WARNING: possible circular locking dependency detected 6.7.0-rc4_net_next_mlx5_5483eb2 #1 Tainted: G I ------------------------------------------------------ ethtool/386089 is trying to acquire lock: ffff88810f21ce68 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}, at: __flush_work+0x74/0x4e0 but task is already holding lock: ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&priv->state_lock){+.+.}-{3:3}: __mutex_lock+0x80/0xc90 arfs_handle_work+0x4b/0x3b0 [mlx5_core] process_one_work+0x1dc/0x4a0 worker_thread+0x1bf/0x3c0 kthread+0xd7/0x100 ret_from_fork+0x2d/0x50 ret_from_fork_asm+0x11/0x20 -> #0 ((work_completion)(&rule->arfs_work)){+.+.}-{0:0}: __lock_acquire+0x17b4/0x2c80 lock_acquire+0xd0/0x2b0 __flush_work+0x7a/0x4e0 __cancel_work_timer+0x131/0x1c0 arfs_del_rules+0x143/0x1e0 [mlx5_core] mlx5e_arfs_disable+0x1b/0x30 [mlx5_core] mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core] ethnl_set_channels+0x28f/0x3b0 ethnl_default_set_doit+0xec/0x240 genl_family_rcv_msg_doit+0xd0/0x120 genl_rcv_msg+0x188/0x2c0 netlink_rcv_skb+0x54/0x100 genl_rcv+0x24/0x40 netlink_unicast+0x1a1/0x270 netlink_sendmsg+0x214/0x460 __sock_sendmsg+0x38/0x60 __sys_sendto+0x113/0x170 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x40/0xe0 entry_SYSCALL_64_after_hwframe+0x46/0x4e other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&priv->state_lock); lock((work_completion)(&rule->arfs_work)); lock(&priv->state_lock); lock((work_completion)(&rule->arfs_work)); *** DEADLOCK *** 3 locks held by ethtool/386089: #0: ffffffff82ea7210 (cb_lock){++++}-{3:3}, at: genl_rcv+0x15/0x40 #1: ffffffff82e94c88 (rtnl_mutex){+.+.}-{3:3}, at: ethnl_default_set_doit+0xd3/0x240 #2: ffff8884a1808cc0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_ethtool_set_channels+0x53/0x200 [mlx5_core] stack backtrace: CPU: 15 PID: 386089 Comm: ethtool Tainted: G I 6.7.0-rc4_net_next_mlx5_5483eb2 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x60/0xa0 check_noncircular+0x144/0x160 __lock_acquire+0x17b4/0x2c80 lock_acquire+0xd0/0x2b0 ? __flush_work+0x74/0x4e0 ? save_trace+0x3e/0x360 ? __flush_work+0x74/0x4e0 __flush_work+0x7a/0x4e0 ? __flush_work+0x74/0x4e0 ? __lock_acquire+0xa78/0x2c80 ? lock_acquire+0xd0/0x2b0 ? mark_held_locks+0x49/0x70 __cancel_work_timer+0x131/0x1c0 ? mark_held_locks+0x49/0x70 arfs_del_rules+0x143/0x1e0 [mlx5_core] mlx5e_arfs_disable+0x1b/0x30 [mlx5_core] mlx5e_ethtool_set_channels+0xcb/0x200 [mlx5_core] ethnl_set_channels+0x28f/0x3b0 ethnl_default_set_doit+0xec/0x240 genl_family_rcv_msg_doit+0xd0/0x120 genl_rcv_msg+0x188/0x2c0 ? ethn ---truncated---

In the Linux kernel, the following vulnerability has been resolved: inet: inet_defrag: prevent sk release while still in use ip_local_out() and other functions can pass skb->sk as function argument. If the skb is a fragment and reassembly happens before such function call returns, the sk must not be released. This affects skb fragments reassembled via netfilter or similar modules, e.g. openvswitch or ct_act.c, when run as part of tx pipeline. Eric Dumazet made an initial analysis of this bug. Quoting Eric: Calling ip_defrag() in output path is also implying skb_orphan(), which is buggy because output path relies on sk not disappearing. A relevant old patch about the issue was : 8282f27449bf ("inet: frag: Always orphan skbs inside ip_defrag()") [..] net/ipv4/ip_output.c depends on skb->sk being set, and probably to an inet socket, not an arbitrary one. If we orphan the packet in ipvlan, then downstream things like FQ packet scheduler will not work properly. We need to change ip_defrag() to only use skb_orphan() when really needed, ie whenever frag_list is going to be used. Eric suggested to stash sk in fragment queue and made an initial patch. However there is a problem with this: If skb is refragmented again right after, ip_do_fragment() will copy head->sk to the new fragments, and sets up destructor to sock_wfree. IOW, we have no choice but to fix up sk_wmem accouting to reflect the fully reassembled skb, else wmem will underflow. This change moves the orphan down into the core, to last possible moment. As ip_defrag_offset is aliased with sk_buff->sk member, we must move the offset into the FRAG_CB, else skb->sk gets clobbered. This allows to delay the orphaning long enough to learn if the skb has to be queued or if the skb is completing the reasm queue. In the former case, things work as before, skb is orphaned. This is safe because skb gets queued/stolen and won't continue past reasm engine. In the latter case, we will steal the skb->sk reference, reattach it to the head skb, and fix up wmem accouting when inet_frag inflates truesize.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: rfcomm: Fix null-ptr-deref in rfcomm_check_security During our fuzz testing of the connection and disconnection process at the RFCOMM layer, we discovered this bug. By comparing the packets from a normal connection and disconnection process with the testcase that triggered a KASAN report. We analyzed the cause of this bug as follows: 1. In the packets captured during a normal connection, the host sends a `Read Encryption Key Size` type of `HCI_CMD` packet (Command Opcode: 0x1408) to the controller to inquire the length of encryption key.After receiving this packet, the controller immediately replies with a Command Completepacket (Event Code: 0x0e) to return the Encryption Key Size. 2. In our fuzz test case, the timing of the controller's response to this packet was delayed to an unexpected point: after the RFCOMM and L2CAP layers had disconnected but before the HCI layer had disconnected. 3. After receiving the Encryption Key Size Response at the time described in point 2, the host still called the rfcomm_check_security function. However, by this time `struct l2cap_conn *conn = l2cap_pi(sk)->chan->conn;` had already been released, and when the function executed `return hci_conn_security(conn->hcon, d->sec_level, auth_type, d->out);`, specifically when accessing `conn->hcon`, a null-ptr-deref error occurred. To fix this bug, check if `sk->sk_state` is BT_CLOSED before calling rfcomm_recv_frame in rfcomm_process_rx.

In the Linux kernel, the following vulnerability has been resolved: net: esp: fix bad handling of pages from page_pool When the skb is reorganized during esp_output (!esp->inline), the pages coming from the original skb fragments are supposed to be released back to the system through put_page. But if the skb fragment pages are originating from a page_pool, calling put_page on them will trigger a page_pool leak which will eventually result in a crash. This leak can be easily observed when using CONFIG_DEBUG_VM and doing ipsec + gre (non offloaded) forwarding: BUG: Bad page state in process ksoftirqd/16 pfn:1451b6 page:00000000de2b8d32 refcount:0 mapcount:0 mapping:0000000000000000 index:0x1451b6000 pfn:0x1451b6 flags: 0x200000000000000(node=0|zone=2) page_type: 0xffffffff() raw: 0200000000000000 dead000000000040 ffff88810d23c000 0000000000000000 raw: 00000001451b6000 0000000000000001 00000000ffffffff 0000000000000000 page dumped because: page_pool leak Modules linked in: ip_gre gre mlx5_ib mlx5_core xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat nf_nat xt_addrtype br_netfilter rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm ib_uverbs ib_core overlay zram zsmalloc fuse [last unloaded: mlx5_core] CPU: 16 PID: 96 Comm: ksoftirqd/16 Not tainted 6.8.0-rc4+ #22 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x36/0x50 bad_page+0x70/0xf0 free_unref_page_prepare+0x27a/0x460 free_unref_page+0x38/0x120 esp_ssg_unref.isra.0+0x15f/0x200 esp_output_tail+0x66d/0x780 esp_xmit+0x2c5/0x360 validate_xmit_xfrm+0x313/0x370 ? validate_xmit_skb+0x1d/0x330 validate_xmit_skb_list+0x4c/0x70 sch_direct_xmit+0x23e/0x350 __dev_queue_xmit+0x337/0xba0 ? nf_hook_slow+0x3f/0xd0 ip_finish_output2+0x25e/0x580 iptunnel_xmit+0x19b/0x240 ip_tunnel_xmit+0x5fb/0xb60 ipgre_xmit+0x14d/0x280 [ip_gre] dev_hard_start_xmit+0xc3/0x1c0 __dev_queue_xmit+0x208/0xba0 ? nf_hook_slow+0x3f/0xd0 ip_finish_output2+0x1ca/0x580 ip_sublist_rcv_finish+0x32/0x40 ip_sublist_rcv+0x1b2/0x1f0 ? ip_rcv_finish_core.constprop.0+0x460/0x460 ip_list_rcv+0x103/0x130 __netif_receive_skb_list_core+0x181/0x1e0 netif_receive_skb_list_internal+0x1b3/0x2c0 napi_gro_receive+0xc8/0x200 gro_cell_poll+0x52/0x90 __napi_poll+0x25/0x1a0 net_rx_action+0x28e/0x300 __do_softirq+0xc3/0x276 ? sort_range+0x20/0x20 run_ksoftirqd+0x1e/0x30 smpboot_thread_fn+0xa6/0x130 kthread+0xcd/0x100 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x31/0x50 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork_asm+0x11/0x20 </TASK> The suggested fix is to introduce a new wrapper (skb_page_unref) that covers page refcounting for page_pool pages as well.

kernel/trace/ftrace.c in the Linux kernel before 2.6.35.5, when debugfs is enabled, does not properly handle interaction between mutex possession and llseek operations, which allows local users to cause a denial of service (NULL pointer dereference and outage of all function tracing files) via an lseek call on a file descriptor associated with the set_ftrace_filter file.

In the Linux kernel, the following vulnerability has been resolved: af_packet: fix vlan_get_tci() vs MSG_PEEK Blamed commit forgot MSG_PEEK case, allowing a crash [1] as found by syzbot. Rework vlan_get_tci() to not touch skb at all, so that it can be used from many cpus on the same skb. Add a const qualifier to skb argument. [1] skbuff: skb_under_panic: text:ffffffff8a8da482 len:32 put:14 head:ffff88807a1d5800 data:ffff88807a1d5810 tail:0x14 end:0x140 dev:<NULL> ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:206 ! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 0 UID: 0 PID: 5880 Comm: syz-executor172 Not tainted 6.13.0-rc3-syzkaller-00762-g9268abe611b0 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:skb_panic net/core/skbuff.c:206 [inline] RIP: 0010:skb_under_panic+0x14b/0x150 net/core/skbuff.c:216 Code: 0b 8d 48 c7 c6 9e 6c 26 8e 48 8b 54 24 08 8b 0c 24 44 8b 44 24 04 4d 89 e9 50 41 54 41 57 41 56 e8 3a 5a 79 f7 48 83 c4 20 90 <0f> 0b 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 RSP: 0018:ffffc90003baf5b8 EFLAGS: 00010286 RAX: 0000000000000087 RBX: dffffc0000000000 RCX: 8565c1eec37aa000 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: ffff88802616fb50 R08: ffffffff817f0a4c R09: 1ffff92000775e50 R10: dffffc0000000000 R11: fffff52000775e51 R12: 0000000000000140 R13: ffff88807a1d5800 R14: ffff88807a1d5810 R15: 0000000000000014 FS: 00007fa03261f6c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffd65753000 CR3: 0000000031720000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> skb_push+0xe5/0x100 net/core/skbuff.c:2636 vlan_get_tci+0x272/0x550 net/packet/af_packet.c:565 packet_recvmsg+0x13c9/0x1ef0 net/packet/af_packet.c:3616 sock_recvmsg_nosec net/socket.c:1044 [inline] sock_recvmsg+0x22f/0x280 net/socket.c:1066 ____sys_recvmsg+0x1c6/0x480 net/socket.c:2814 ___sys_recvmsg net/socket.c:2856 [inline] do_recvmmsg+0x426/0xab0 net/socket.c:2951 __sys_recvmmsg net/socket.c:3025 [inline] __do_sys_recvmmsg net/socket.c:3048 [inline] __se_sys_recvmmsg net/socket.c:3041 [inline] __x64_sys_recvmmsg+0x199/0x250 net/socket.c:3041 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83

In the Linux kernel, the following vulnerability has been resolved: ASoC: Intel: sof_sdw: Add space for a terminator into DAIs array The code uses the initialised member of the asoc_sdw_dailink struct to determine if a member of the array is in use. However in the case the array is completely full this will lead to an access 1 past the end of the array, expand the array by one entry to include a space for a terminator.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Correct the migration DMA map direction The SVM DMA device map direction should be set the same as the DMA unmap setting, otherwise the DMA core will report the following warning. Before finialize this solution, there're some discussion on the DMA mapping type(stream-based or coherent) in this KFD migration case, followed by https://lore.kernel.org/all/04d4ab32 -45a1-4b88-86ee-fb0f35a0ca40@amd.com/T/. As there's no dma_sync_single_for_*() in the DMA buffer accessed that because this migration operation should be sync properly and automatically. Give that there's might not be a performance problem in various cache sync policy of DMA sync. Therefore, in order to simplify the DMA direction setting alignment, let's set the DMA map direction as BIDIRECTIONAL. [ 150.834218] WARNING: CPU: 8 PID: 1812 at kernel/dma/debug.c:1028 check_unmap+0x1cc/0x930 [ 150.834225] Modules linked in: amdgpu(OE) amdxcp drm_exec(OE) gpu_sched drm_buddy(OE) drm_ttm_helper(OE) ttm(OE) drm_suballoc_helper(OE) drm_display_helper(OE) drm_kms_helper(OE) i2c_algo_bit rpcsec_gss_krb5 auth_rpcgss nfsv4 nfs lockd grace netfs xt_conntrack xt_MASQUERADE nf_conntrack_netlink xfrm_user xfrm_algo iptable_nat xt_addrtype iptable_filter br_netfilter nvme_fabrics overlay nfnetlink_cttimeout nfnetlink openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c bridge stp llc sch_fq_codel intel_rapl_msr amd_atl intel_rapl_common snd_hda_codec_realtek snd_hda_codec_generic snd_hda_scodec_component snd_hda_codec_hdmi snd_hda_intel snd_intel_dspcfg edac_mce_amd snd_pci_acp6x snd_hda_codec snd_acp_config snd_hda_core snd_hwdep snd_soc_acpi kvm_amd sunrpc snd_pcm kvm binfmt_misc snd_seq_midi crct10dif_pclmul snd_seq_midi_event ghash_clmulni_intel sha512_ssse3 snd_rawmidi nls_iso8859_1 sha256_ssse3 sha1_ssse3 snd_seq aesni_intel snd_seq_device crypto_simd snd_timer cryptd input_leds [ 150.834310] wmi_bmof serio_raw k10temp rapl snd sp5100_tco ipmi_devintf soundcore ccp ipmi_msghandler cm32181 industrialio mac_hid msr parport_pc ppdev lp parport efi_pstore drm(OE) ip_tables x_tables pci_stub crc32_pclmul nvme ahci libahci i2c_piix4 r8169 nvme_core i2c_designware_pci realtek i2c_ccgx_ucsi video wmi hid_generic cdc_ether usbnet usbhid hid r8152 mii [ 150.834354] CPU: 8 PID: 1812 Comm: rocrtst64 Tainted: G OE 6.10.0-custom #492 [ 150.834358] Hardware name: AMD Majolica-RN/Majolica-RN, BIOS RMJ1009A 06/13/2021 [ 150.834360] RIP: 0010:check_unmap+0x1cc/0x930 [ 150.834363] Code: c0 4c 89 4d c8 e8 34 bf 86 00 4c 8b 4d c8 4c 8b 45 c0 48 8b 4d b8 48 89 c6 41 57 4c 89 ea 48 c7 c7 80 49 b4 84 e8 b4 81 f3 ff <0f> 0b 48 c7 c7 04 83 ac 84 e8 76 ba fc ff 41 8b 76 4c 49 8d 7e 50 [ 150.834365] RSP: 0018:ffffaac5023739e0 EFLAGS: 00010086 [ 150.834368] RAX: 0000000000000000 RBX: ffffffff8566a2e0 RCX: 0000000000000027 [ 150.834370] RDX: ffff8f6a8f621688 RSI: 0000000000000001 RDI: ffff8f6a8f621680 [ 150.834372] RBP: ffffaac502373a30 R08: 00000000000000c9 R09: ffffaac502373850 [ 150.834373] R10: ffffaac502373848 R11: ffffffff84f46328 R12: ffffaac502373a40 [ 150.834375] R13: ffff8f6741045330 R14: ffff8f6741a77700 R15: ffffffff84ac831b [ 150.834377] FS: 00007faf0fc94c00(0000) GS:ffff8f6a8f600000(0000) knlGS:0000000000000000 [ 150.834379] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 150.834381] CR2: 00007faf0b600020 CR3: 000000010a52e000 CR4: 0000000000350ef0 [ 150.834383] Call Trace: [ 150.834385] <TASK> [ 150.834387] ? show_regs+0x6d/0x80 [ 150.834393] ? __warn+0x8c/0x140 [ 150.834397] ? check_unmap+0x1cc/0x930 [ 150.834400] ? report_bug+0x193/0x1a0 [ 150.834406] ? handle_bug+0x46/0x80 [ 150.834410] ? exc_invalid_op+0x1d/0x80 [ 150.834413] ? asm_exc_invalid_op+0x1f/0x30 [ 150.834420] ? check_unmap+0x1cc/0x930 [ 150.834425] debug_dma_unmap_page+0x86/0x90 [ 150.834431] ? srso_return_thunk+0x5/0x5f [ 150.834435] ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/vc4: hdmi: Avoid hang with debug registers when suspended Trying to read /sys/kernel/debug/dri/1/hdmi1_regs when the hdmi is disconnected results in a fatal system hang. This is due to the pm suspend code disabling the dvp clock. That is just a gate of the 108MHz clock in DVP_HT_RPI_MISC_CONFIG, which results in accesses hanging AXI bus. Protect against this.

In the Linux kernel, the following vulnerability has been resolved: bpf: Call free_htab_elem() after htab_unlock_bucket() For htab of maps, when the map is removed from the htab, it may hold the last reference of the map. bpf_map_fd_put_ptr() will invoke bpf_map_free_id() to free the id of the removed map element. However, bpf_map_fd_put_ptr() is invoked while holding a bucket lock (raw_spin_lock_t), and bpf_map_free_id() attempts to acquire map_idr_lock (spinlock_t), triggering the following lockdep warning: ============================= [ BUG: Invalid wait context ] 6.11.0-rc4+ #49 Not tainted ----------------------------- test_maps/4881 is trying to lock: ffffffff84884578 (map_idr_lock){+...}-{3:3}, at: bpf_map_free_id.part.0+0x21/0x70 other info that might help us debug this: context-{5:5} 2 locks held by test_maps/4881: #0: ffffffff846caf60 (rcu_read_lock){....}-{1:3}, at: bpf_fd_htab_map_update_elem+0xf9/0x270 #1: ffff888149ced148 (&htab->lockdep_key#2){....}-{2:2}, at: htab_map_update_elem+0x178/0xa80 stack backtrace: CPU: 0 UID: 0 PID: 4881 Comm: test_maps Not tainted 6.11.0-rc4+ #49 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ... Call Trace: <TASK> dump_stack_lvl+0x6e/0xb0 dump_stack+0x10/0x20 __lock_acquire+0x73e/0x36c0 lock_acquire+0x182/0x450 _raw_spin_lock_irqsave+0x43/0x70 bpf_map_free_id.part.0+0x21/0x70 bpf_map_put+0xcf/0x110 bpf_map_fd_put_ptr+0x9a/0xb0 free_htab_elem+0x69/0xe0 htab_map_update_elem+0x50f/0xa80 bpf_fd_htab_map_update_elem+0x131/0x270 htab_map_update_elem+0x50f/0xa80 bpf_fd_htab_map_update_elem+0x131/0x270 bpf_map_update_value+0x266/0x380 __sys_bpf+0x21bb/0x36b0 __x64_sys_bpf+0x45/0x60 x64_sys_call+0x1b2a/0x20d0 do_syscall_64+0x5d/0x100 entry_SYSCALL_64_after_hwframe+0x76/0x7e One way to fix the lockdep warning is using raw_spinlock_t for map_idr_lock as well. However, bpf_map_alloc_id() invokes idr_alloc_cyclic() after acquiring map_idr_lock, it will trigger a similar lockdep warning because the slab's lock (s->cpu_slab->lock) is still a spinlock. Instead of changing map_idr_lock's type, fix the issue by invoking htab_put_fd_value() after htab_unlock_bucket(). However, only deferring the invocation of htab_put_fd_value() is not enough, because the old map pointers in htab of maps can not be saved during batched deletion. Therefore, also defer the invocation of free_htab_elem(), so these to-be-freed elements could be linked together similar to lru map. There are four callers for ->map_fd_put_ptr: (1) alloc_htab_elem() (through htab_put_fd_value()) It invokes ->map_fd_put_ptr() under a raw_spinlock_t. The invocation of htab_put_fd_value() can not simply move after htab_unlock_bucket(), because the old element has already been stashed in htab->extra_elems. It may be reused immediately after htab_unlock_bucket() and the invocation of htab_put_fd_value() after htab_unlock_bucket() may release the newly-added element incorrectly. Therefore, saving the map pointer of the old element for htab of maps before unlocking the bucket and releasing the map_ptr after unlock. Beside the map pointer in the old element, should do the same thing for the special fields in the old element as well. (2) free_htab_elem() (through htab_put_fd_value()) Its caller includes __htab_map_lookup_and_delete_elem(), htab_map_delete_elem() and __htab_map_lookup_and_delete_batch(). For htab_map_delete_elem(), simply invoke free_htab_elem() after htab_unlock_bucket(). For __htab_map_lookup_and_delete_batch(), just like lru map, linking the to-be-freed element into node_to_free list and invoking free_htab_elem() for these element after unlock. It is safe to reuse batch_flink as the link for node_to_free, because these elements have been removed from the hash llist. Because htab of maps doesn't support lookup_and_delete operation, __htab_map_lookup_and_delete_elem() doesn't have the problem, so kept it as ---truncated---

In the Linux kernel, the following vulnerability has been resolved: riscv: Fix sleeping in invalid context in die() die() can be called in exception handler, and therefore cannot sleep. However, die() takes spinlock_t which can sleep with PREEMPT_RT enabled. That causes the following warning: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 285, name: mutex preempt_count: 110001, expected: 0 RCU nest depth: 0, expected: 0 CPU: 0 UID: 0 PID: 285 Comm: mutex Not tainted 6.12.0-rc7-00022-ge19049cf7d56-dirty #234 Hardware name: riscv-virtio,qemu (DT) Call Trace: dump_backtrace+0x1c/0x24 show_stack+0x2c/0x38 dump_stack_lvl+0x5a/0x72 dump_stack+0x14/0x1c __might_resched+0x130/0x13a rt_spin_lock+0x2a/0x5c die+0x24/0x112 do_trap_insn_illegal+0xa0/0xea _new_vmalloc_restore_context_a0+0xcc/0xd8 Oops - illegal instruction [#1] Switch to use raw_spinlock_t, which does not sleep even with PREEMPT_RT enabled.

There are use-after-free vulnerabilities caused by timer handler in net/rose/rose_timer.c of linux that allow attackers to crash linux kernel without any privileges.

In the Linux kernel, the following vulnerability has been resolved: geneve: do not assume mac header is set in geneve_xmit_skb() We should not assume mac header is set in output path. Use skb_eth_hdr() instead of eth_hdr() to fix the issue. sysbot reported the following : WARNING: CPU: 0 PID: 11635 at include/linux/skbuff.h:3052 skb_mac_header include/linux/skbuff.h:3052 [inline] WARNING: CPU: 0 PID: 11635 at include/linux/skbuff.h:3052 eth_hdr include/linux/if_ether.h:24 [inline] WARNING: CPU: 0 PID: 11635 at include/linux/skbuff.h:3052 geneve_xmit_skb drivers/net/geneve.c:898 [inline] WARNING: CPU: 0 PID: 11635 at include/linux/skbuff.h:3052 geneve_xmit+0x4c38/0x5730 drivers/net/geneve.c:1039 Modules linked in: CPU: 0 UID: 0 PID: 11635 Comm: syz.4.1423 Not tainted 6.12.0-syzkaller-10296-gaaf20f870da0 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:skb_mac_header include/linux/skbuff.h:3052 [inline] RIP: 0010:eth_hdr include/linux/if_ether.h:24 [inline] RIP: 0010:geneve_xmit_skb drivers/net/geneve.c:898 [inline] RIP: 0010:geneve_xmit+0x4c38/0x5730 drivers/net/geneve.c:1039 Code: 21 c6 02 e9 35 d4 ff ff e8 a5 48 4c fb 90 0f 0b 90 e9 fd f5 ff ff e8 97 48 4c fb 90 0f 0b 90 e9 d8 f5 ff ff e8 89 48 4c fb 90 <0f> 0b 90 e9 41 e4 ff ff e8 7b 48 4c fb 90 0f 0b 90 e9 cd e7 ff ff RSP: 0018:ffffc90003b2f870 EFLAGS: 00010283 RAX: 000000000000037a RBX: 000000000000ffff RCX: ffffc9000dc3d000 RDX: 0000000000080000 RSI: ffffffff86428417 RDI: 0000000000000003 RBP: ffffc90003b2f9f0 R08: 0000000000000003 R09: 000000000000ffff R10: 000000000000ffff R11: 0000000000000002 R12: ffff88806603c000 R13: 0000000000000000 R14: ffff8880685b2780 R15: 0000000000000e23 FS: 00007fdc2deed6c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b30a1dff8 CR3: 0000000056b8c000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __netdev_start_xmit include/linux/netdevice.h:5002 [inline] netdev_start_xmit include/linux/netdevice.h:5011 [inline] __dev_direct_xmit+0x58a/0x720 net/core/dev.c:4490 dev_direct_xmit include/linux/netdevice.h:3181 [inline] packet_xmit+0x1e4/0x360 net/packet/af_packet.c:285 packet_snd net/packet/af_packet.c:3146 [inline] packet_sendmsg+0x2700/0x5660 net/packet/af_packet.c:3178 sock_sendmsg_nosec net/socket.c:711 [inline] __sock_sendmsg net/socket.c:726 [inline] __sys_sendto+0x488/0x4f0 net/socket.c:2197 __do_sys_sendto net/socket.c:2204 [inline] __se_sys_sendto net/socket.c:2200 [inline] __x64_sys_sendto+0xe0/0x1c0 net/socket.c:2200 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

There is a sleep-in-atomic bug in /net/nfc/netlink.c that allows an attacker to crash the Linux kernel by simulating a nfc device from user-space.

In the Linux kernel, the following vulnerability has been resolved: svcrdma: Address an integer overflow Dan Carpenter reports: > Commit 78147ca8b4a9 ("svcrdma: Add a "parsed chunk list" data > structure") from Jun 22, 2020 (linux-next), leads to the following > Smatch static checker warning: > > net/sunrpc/xprtrdma/svc_rdma_recvfrom.c:498 xdr_check_write_chunk() > warn: potential user controlled sizeof overflow 'segcount * 4 * 4' > > net/sunrpc/xprtrdma/svc_rdma_recvfrom.c > 488 static bool xdr_check_write_chunk(struct svc_rdma_recv_ctxt *rctxt) > 489 { > 490 u32 segcount; > 491 __be32 *p; > 492 > 493 if (xdr_stream_decode_u32(&rctxt->rc_stream, &segcount)) > ^^^^^^^^ > > 494 return false; > 495 > 496 /* A bogus segcount causes this buffer overflow check to fail. */ > 497 p = xdr_inline_decode(&rctxt->rc_stream, > --> 498 segcount * rpcrdma_segment_maxsz * sizeof(*p)); > > > segcount is an untrusted u32. On 32bit systems anything >= SIZE_MAX / 16 will > have an integer overflow and some those values will be accepted by > xdr_inline_decode().

In the Linux kernel, the following vulnerability has been resolved: zram: fix NULL pointer in comp_algorithm_show() LTP reported a NULL pointer dereference as followed: CPU: 7 UID: 0 PID: 5995 Comm: cat Kdump: loaded Not tainted 6.12.0-rc6+ #3 Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 pstate: 40400005 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __pi_strcmp+0x24/0x140 lr : zcomp_available_show+0x60/0x100 [zram] sp : ffff800088b93b90 x29: ffff800088b93b90 x28: 0000000000000001 x27: 0000000000400cc0 x26: 0000000000000ffe x25: ffff80007b3e2388 x24: 0000000000000000 x23: ffff80007b3e2390 x22: ffff0004041a9000 x21: ffff80007b3e2900 x20: 0000000000000000 x19: 0000000000000000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: ffff80007b3e2900 x9 : ffff80007b3cb280 x8 : 0101010101010101 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000040 x4 : 0000000000000000 x3 : 00656c722d6f7a6c x2 : 0000000000000000 x1 : ffff80007b3e2900 x0 : 0000000000000000 Call trace: __pi_strcmp+0x24/0x140 comp_algorithm_show+0x40/0x70 [zram] dev_attr_show+0x28/0x80 sysfs_kf_seq_show+0x90/0x140 kernfs_seq_show+0x34/0x48 seq_read_iter+0x1d4/0x4e8 kernfs_fop_read_iter+0x40/0x58 new_sync_read+0x9c/0x168 vfs_read+0x1a8/0x1f8 ksys_read+0x74/0x108 __arm64_sys_read+0x24/0x38 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0xc8/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x38/0x138 el0t_64_sync_handler+0xc0/0xc8 el0t_64_sync+0x188/0x190 The zram->comp_algs[ZRAM_PRIMARY_COMP] can be NULL in zram_add() if comp_algorithm_set() has not been called. User can access the zram device by sysfs after device_add_disk(), so there is a time window to trigger the NULL pointer dereference. Move it ahead device_add_disk() to make sure when user can access the zram device, it is ready. comp_algorithm_set() is protected by zram->init_lock in other places and no such problem.

A memory leak problem was found in ctnetlink_create_conntrack in net/netfilter/nf_conntrack_netlink.c in the Linux Kernel. This issue may allow a local attacker with CAP_NET_ADMIN privileges to cause a denial of service (DoS) attack due to a refcount overflow.

A flaw null pointer dereference in the Linux kernel UDF file system functionality was found in the way user triggers udf_file_write_iter function for the malicious UDF image. A local user could use this flaw to crash the system. Actual from Linux kernel 4.2-rc1 till 5.17-rc2.

In the Linux kernel, the following vulnerability has been resolved: mptcp: error out earlier on disconnect Eric reported a division by zero splat in the MPTCP protocol: Oops: divide error: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 1 UID: 0 PID: 6094 Comm: syz-executor317 Not tainted 6.12.0-rc5-syzkaller-00291-g05b92660cdfe #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:__tcp_select_window+0x5b4/0x1310 net/ipv4/tcp_output.c:3163 Code: f6 44 01 e3 89 df e8 9b 75 09 f8 44 39 f3 0f 8d 11 ff ff ff e8 0d 74 09 f8 45 89 f4 e9 04 ff ff ff e8 00 74 09 f8 44 89 f0 99 <f7> 7c 24 14 41 29 d6 45 89 f4 e9 ec fe ff ff e8 e8 73 09 f8 48 89 RSP: 0018:ffffc900041f7930 EFLAGS: 00010293 RAX: 0000000000017e67 RBX: 0000000000017e67 RCX: ffffffff8983314b RDX: 0000000000000000 RSI: ffffffff898331b0 RDI: 0000000000000004 RBP: 00000000005d6000 R08: 0000000000000004 R09: 0000000000017e67 R10: 0000000000003e80 R11: 0000000000000000 R12: 0000000000003e80 R13: ffff888031d9b440 R14: 0000000000017e67 R15: 00000000002eb000 FS: 00007feb5d7f16c0(0000) GS:ffff8880b8700000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007feb5d8adbb8 CR3: 0000000074e4c000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __tcp_cleanup_rbuf+0x3e7/0x4b0 net/ipv4/tcp.c:1493 mptcp_rcv_space_adjust net/mptcp/protocol.c:2085 [inline] mptcp_recvmsg+0x2156/0x2600 net/mptcp/protocol.c:2289 inet_recvmsg+0x469/0x6a0 net/ipv4/af_inet.c:885 sock_recvmsg_nosec net/socket.c:1051 [inline] sock_recvmsg+0x1b2/0x250 net/socket.c:1073 __sys_recvfrom+0x1a5/0x2e0 net/socket.c:2265 __do_sys_recvfrom net/socket.c:2283 [inline] __se_sys_recvfrom net/socket.c:2279 [inline] __x64_sys_recvfrom+0xe0/0x1c0 net/socket.c:2279 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7feb5d857559 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 51 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007feb5d7f1208 EFLAGS: 00000246 ORIG_RAX: 000000000000002d RAX: ffffffffffffffda RBX: 00007feb5d8e1318 RCX: 00007feb5d857559 RDX: 000000800000000e RSI: 0000000000000000 RDI: 0000000000000003 RBP: 00007feb5d8e1310 R08: 0000000000000000 R09: ffffffff81000000 R10: 0000000000000100 R11: 0000000000000246 R12: 00007feb5d8e131c R13: 00007feb5d8ae074 R14: 000000800000000e R15: 00000000fffffdef and provided a nice reproducer. The root cause is the current bad handling of racing disconnect. After the blamed commit below, sk_wait_data() can return (with error) with the underlying socket disconnected and a zero rcv_mss. Catch the error and return without performing any additional operations on the current socket.

A use-after-free flaw was found in fs/ext4/namei.c:dx_insert_block() in the Linux kernel’s filesystem sub-component. This flaw allows a local attacker with a user privilege to cause a denial of service.

A use-after-free vulnerability was found in the Linux kernel in drivers/net/hamradio. This flaw allows a local attacker with a user privilege to cause a denial of service (DOS) when the mkiss or sixpack device is detached and reclaim resources early.

In the Linux kernel, the following vulnerability has been resolved: net: vlan: fix underflow for the real_dev refcnt Inject error before dev_hold(real_dev) in register_vlan_dev(), and execute the following testcase: ip link add dev dummy1 type dummy ip link add name dummy1.100 link dummy1 type vlan id 100 ip link del dev dummy1 When the dummy netdevice is removed, we will get a WARNING as following: ======================================================================= refcount_t: decrement hit 0; leaking memory. WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 and an endless loop of: ======================================================================= unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824 That is because dev_put(real_dev) in vlan_dev_free() be called without dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev underflow. Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev symmetrical.