An Improper Input Validation vulnerability in the routing protocol daemon (rpd) of Juniper Networks allows an attacker to cause a Denial of Service (DoS )to the device upon receiving and processing a specific malformed ISO VPN BGP UPDATE packet. Continued receipt of this packet will cause a sustained Denial of Service condition. This issue affects: * Juniper Networks Junos OS: * All versions prior to 20.4R3-S6; * 21.1 versions prior to 21.1R3-S5; * 21.2 versions prior to 21.2R3-S4; * 21.3 versions prior to 21.3R3-S3; * 21.4 versions prior to 21.4R3-S3; * 22.1 versions prior to 22.1R2-S2, 22.1R3; * 22.2 versions prior to 22.2R2-S1, 22.2R3; * 22.3 versions prior to 22.3R1-S2, 22.3R2. Juniper Networks Junos OS Evolved: * All versions prior to 20.4R3-S6-EVO; * 21.1-EVO version 21.1R1-EVO and later versions prior to 21.2R3-S4-EVO; * 21.3-EVO versions prior to 21.3R3-S3-EVO; * 21.4-EVO versions prior to 21.4R3-S3-EVO; * 22.1-EVO versions prior to 22.1R3-EVO; * 22.2-EVO versions prior to 22.2R2-S1-EVO, 22.2R3-EVO; * 22.3-EVO versions prior to 22.3R1-S2-EVO, 22.3R2-EVO.
An Improper Input Validation vulnerability in the Packet Forwarding Engine of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause memory leak, leading to Denial of Service (DoS). On all Junos OS QFX5000 Series platforms, when pseudo-VTEP (Virtual Tunnel End Point) is configured under EVPN-VXLAN scenario, and specific DHCP packets are transmitted, DMA memory leak is observed. Continuous receipt of these specific DHCP packets will cause memory leak to reach 99% and then cause the protocols to stop working and traffic is impacted, leading to Denial of Service (DoS) condition. A manual reboot of the system recovers from the memory leak. To confirm the memory leak, monitor for "sheaf:possible leak" and "vtep not found" messages in the logs. This issue affects: Juniper Networks Junos OS QFX5000 Series: * All versions prior to 20.4R3-S6; * 21.1 versions prior to 21.1R3-S5; * 21.2 versions prior to 21.2R3-S5; * 21.3 versions prior to 21.3R3-S4; * 21.4 versions prior to 21.4R3-S3; * 22.1 versions prior to 22.1R3-S2; * 22.2 versions prior to 22.2R2-S2, 22.2R3; * 22.3 versions prior to 22.3R2-S1, 22.3R3; * 22.4 versions prior to 22.4R1-S2, 22.4R2.
An Improperly Implemented Security Check for Standard vulnerability in storm control of Juniper Networks Junos OS QFX5k devices allows packets to be punted to ARP queue causing a l2 loop resulting in a DDOS violations and DDOS syslog. This issue is triggered when Storm control is enabled and ICMPv6 packets are present on device. This issue affects Juniper Networks: Junos OS * All versions prior to 20.2R3-S6 on QFX5k; * 20.3 versions prior to 20.3R3-S5 on QFX5k; * 20.4 versions prior to 20.4R3-S5 on QFX5k; * 21.1 versions prior to 21.1R3-S4 on QFX5k; * 21.2 versions prior to 21.2R3-S3 on QFX5k; * 21.3 versions prior to 21.3R3-S2 on QFX5k; * 21.4 versions prior to 21.4R3 on QFX5k; * 22.1 versions prior to 22.1R3 on QFX5k; * 22.2 versions prior to 22.2R2 on QFX5k.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series allows a unauthenticated network-based attacker to cause an infinite loop, resulting in a Denial of Service (DoS). An attacker who sends malformed TCP traffic via an interface configured with PPPoE, causes an infinite loop on the respective PFE. This results in consuming all resources and a manual restart is needed to recover. This issue affects interfaces with PPPoE configured and tcp-mss enabled. This issue affects Juniper Networks Junos OS * All versions prior to 20.4R3-S7; * 21.1 version 21.1R1 and later versions; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S3; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3; * 22.3 versions prior to 22.3R2-S2; * 22.4 versions prior to 22.4R2;
An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX10000 Series allows a network based attacker to cause a Denial of Service (DoS). If a specific valid IP packet is received and that packet needs to be routed over a VXLAN tunnel, this will result in a PFE wedge condition due to which traffic gets impacted. As this is not a crash and restart scenario, this condition will persist until the system is rebooted to recover. This issue affects Juniper Networks Junos OS on QFX10000: 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S5; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2; 22.3 versions prior to 22.3R1-S2, 22.3R2.
An Improper Check or Handling of Exceptional Conditions vulnerability in the UTM (Unified Threat Management) Web-Filtering feature of Juniper Networks Junos OS on SRX Series causes a jbuf memory leak to occur when accessing certain websites, eventually leading to a Denial of Service (DoS) condition. Service restoration is only possible by rebooting the system. The jbuf memory leak only occurs in SSL Proxy and UTM Web-Filtering configurations. Other products, platforms, and configurations are not affected by this vulnerability. This issue affects Juniper Networks Junos OS on SRX Series: 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R2-S1, 22.3R3; 22.4 versions prior to 22.4R1-S2, 22.4R2. This issue does not affect Juniper Networks Junos OS versions prior to 22.2R2.
An Improper Handling of Exceptional Conditions vulnerability in packet processing of Juniper Networks Junos OS on MX Series allows an unauthenticated network-based attacker to send specific packets to an Aggregated Multiservices (AMS) interface on the device, causing the packet forwarding engine (PFE) to crash, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue is only triggered by packets destined to a local-interface via a service-interface (AMS). AMS is only supported on the MS-MPC, MS-MIC, and MX-SPC3 cards. This issue is not experienced on other types of interfaces or configurations. Additionally, transit traffic does not trigger this issue. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S12; 20.2 versions prior to 20.2R3-S8; 20.4 versions prior to 20.4R3-S7; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S5; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S2; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R2-S1, 22.3R3; 22.4 versions prior to 22.4R1-S2, 22.4R2.
An Improper Check or Handling of Exceptional Conditions within the storm control feature of Juniper Networks Junos OS allows an attacker sending a high rate of traffic to cause a Denial of Service. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Storm control monitors the level of applicable incoming traffic and compares it with the level specified. If the combined level of the applicable traffic exceeds the specified level, the switch drops packets for the controlled traffic types. This issue affects Juniper Networks Junos OS on QFX10002: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.
An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network based, unauthenticated attacker to cause an RPD crash leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Upon receipt of a malformed BGP flowspec update, RPD will crash resulting in a Denial of Service. This issue affects Juniper Networks Junos OS: All versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2; Juniper Networks Junos OS Evolved: All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R2-EVO; 20.3 versions prior to 20.3R2-EVO;
An Improper Validation of Syntactic Correctness of Input vulnerability in the IPsec library used by kmd and iked of Juniper Networks Junos OS on SRX Series and MX Series allows an unauthenticated, network-based attacker to cause a complete Denial-of-Service (DoS). If an affected device receives a specifically malformed first ISAKMP packet from the initiator, the kmd/iked process will crash and restart, which momentarily prevents new security associations (SAs) for from being established. Repeated exploitation of this vulnerability causes a complete inability to establish new VPN connections. This issue affects Junos OS on SRX Series and MX Series: * all versions before 22.4R3-S9, * 23.2 version before 23.2R2-S6, * 23.4 version before 23.4R2-S7, * 24.2 versions before 24.2R2-S4, * 24.4 versions before 24.4R2-S3, * 25.2 versions before 25.2R1-S2, 25.2R2.
An Improper Check for Unusual or Exceptional Conditions vulnerability in the flow daemon (flowd) of Juniper Networks Junos OS on SRX Series allows an attacker sending a specific, malformed ICMPv6 packet to cause the srxpfe process to crash and restart. Continued receipt and processing of these packets will repeatedly crash the srxpfe process and sustain the Denial of Service (DoS) condition. During NAT64 translation, receipt of a specific, malformed ICMPv6 packet destined to the device will cause the srxpfe process to crash and restart. This issue cannot be triggered using IPv4 nor other IPv6 traffic. This issue affects Junos OS on SRX Series: * all versions before 21.2R3-S10, * all versions of 21.3, * from 21.4 before 21.4R3-S12, * all versions of 22.1, * from 22.2 before 22.2R3-S8, * all versions of 22.4, * from 22.4 before 22.4R3-S9, * from 23.2 before 23.2R2-S6, * from 23.4 before 23.4R2-S7, * from 24.2 before 24.2R2-S3, * from 24.4 before 24.4R2-S3, * from 25.2 before 25.2R1-S2, 25.2R2.
An Improper Validation of Syntactic Correctness of Input vulnerability in Intrusion Detection and Prevention (IDP) of Juniper Networks SRX Series and MX Series allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). Continued receipt of this specific packet will cause a sustained Denial of Service condition. On all SRX Series and MX Series platforms, where IDP is enabled and a specific malformed SSL packet is received, the SSL detector crashes leading to an FPC core. This issue affects Juniper Networks SRX Series and MX Series prior to SigPack 3598. In order to identify the current SigPack version, following command can be used: user@junos# show security idp security-package-version
An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If specific traffic is received on MX Series and its rate exceeds the respective DDoS protection limit the ingress PFE will crash and restart. Continued receipt of this traffic will create a sustained DoS condition. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S5; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.
An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When certain specific crafted BGP UPDATE messages are received over an established BGP session, one BGP session may be torn down with an UPDATE message error, or the issue may propagate beyond the local system which will remain non-impacted, but may affect one or more remote systems. This issue is exploitable remotely as the crafted UPDATE message can propagate through unaffected systems and intermediate BGP speakers. Continuous receipt of the crafted BGP UPDATE messages will create a sustained Denial of Service (DoS) condition for impacted devices. This issue affects eBGP and iBGP, in both IPv4 and IPv6 implementations. This issue requires a remote attacker to have at least one established BGP session. Improper Input Validation, Denial of Service vulnerability in Juniper Networks, Inc. Junos OS (BGP, rpd modules), Juniper Networks, Inc. Junos OS Evolved (BGP, rpd modules) allows Fuzzing.This issue affects Junos OS: * All versions before 20.4R3-S10, * from 21.1R1 through 21.*, * from 21.2 before 21.2R3-S5, * from 21.3 before 21.3R3-S5, * from 21.4 before 21.4R3-S7 (unaffected from 21.4R3-S5, affected from 21.4R3-S6) * from 22.1 before 22.1R3-S4, * from 22.2 before 22.2R3-S3, * from 22.3 before 22.3R3-S1, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2. Junos OS Evolved: * All versions before 20.4R3-S10-EVO, * from 21.2-EVO before 21.2R3-S7-EVO, * from 21.3-EVO before 21.3R3-S5-EVO, * from 21.4-EVO before 21.4R3-S5-EVO, * from 22.1-EVO before 22.1R3-S4-EVO, * from 22.2-EVO before 22.2R3-S3-EVO, * from 22.3-EVO before 22.3R3-S1-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.
BIND was improperly sequencing cleanup operations on upstream recursion fetch contexts, leading in some cases to a use-after-free error that can trigger an assertion failure and crash in named. Affects BIND 9.0.0 to 9.8.x, 9.9.0 to 9.9.11, 9.10.0 to 9.10.6, 9.11.0 to 9.11.2, 9.9.3-S1 to 9.9.11-S1, 9.10.5-S1 to 9.10.6-S1, 9.12.0a1 to 9.12.0rc1.
Receipt of a malformed BGP OPEN message may cause the routing protocol daemon (rpd) process to crash and restart. By continuously sending specially crafted BGP OPEN messages, an attacker can repeatedly crash the rpd process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.3 prior to 12.3R12-S4, 12.3R13, 12.3R3-S4; 12.3X48 prior to 12.3X48-D50; 13.3 prior to 13.3R4-S11, 13.3R10; 14.1 prior to 14.1R8-S3, 14.1R9; 14.1X53 prior to 14.1X53-D40; 14.1X55 prior to 14.1X55-D35; 14.2 prior to 14.2R4-S7, 14.2R6-S4, 14.2R7; 15.1 prior to 15.1F2-S11, 15.1F4-S1-J1, 15.1F5-S3, 15.1F6, 15.1R4; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D33, 15.1X53-D50.
In Point to MultiPoint (P2MP) scenarios within established sessions between network or adjacent neighbors the improper use of a source to destination copy write operation combined with a Stack-based Buffer Overflow on certain specific packets processed by the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved sent by a remote unauthenticated network attacker causes the RPD to crash causing a Denial of Service (DoS). Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 19.2R1. Juniper Networks Junos OS Evolved 20.1 versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R3-EVO; 20.3 versions prior to 20.3R2-EVO.
An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks JUNOS OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that kernel and netisr process are shown to be using a lot of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 16 root -72 - 0K 304K WAIT 1 839:40 88.96% intr{swi1: netisr 0} 0 root 97 - 0K 160K RUN 1 732:43 87.99% kernel{bcm560xgmac0 que} This issue affects Juniper Networks JUNOS OS on EX2300 Series, EX3400 Series, and ACX710: All versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2.
A Use of Uninitialized Resource vulnerability in the Border Gateway Protocol (BGP) software of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to send specific genuine BGP packets to a device configured with BGP to cause a Denial of Service (DoS) by crashing the Routing Protocol Daemon (rpd). This issue is triggered when the packets attempt to initiate a BGP connection before a BGP session is successfully established. Continued receipt of these specific BGP packets will cause a sustained Denial of Service condition. This issue is triggerable in both iBGP and eBGP deployments. This issue affects: Juniper Networks Junos OS 21.1 version 21.1R1 and later versions prior to 21.1R3-S5; 21.2 version 21.2R1 and later versions prior to 21.2R3-S2; 21.3 version 21.3R1 and later versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1. This issue affects: Juniper Networks Junos OS Evolved 21.1-EVO version 21.1R1-EVO and later versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.1R1-EVO.
A Loop with Unreachable Exit Condition ('Infinite Loop') vulnerability in the SIP application layer gateway (ALG) of Juniper Networks Junos OS on SRX Series and MX Series with MX-SPC3 or MS-MPC allows an unauthenticated network-based attacker sending specific SIP messages over TCP to crash the flow management process, leading to a Denial of Service (DoS). On SRX Series, and MX Series with MX-SPC3 or MS-MPC service cards, receipt of multiple SIP messages causes the SIP headers to be parsed incorrectly, eventually causing a continuous loop and leading to a watchdog timer expiration, crashing the flowd process on SRX Series and MX Series with MX-SPC3, or mspmand process on MX Series with MS-MPC. This issue only occurs over TCP. SIP messages sent over UDP cannot trigger this issue. This issue affects Junos OS on SRX Series and MX Series with MX-SPC3 and MS-MPC: * all versions before 21.2R3-S10, * from 21.4 before 21.4R3-S12, * from 22.4 before 22.4R3-S8, * from 23.2 before 23.2R2-S5, * from 23.4 before 23.4R2-S6, * from 24.2 before 24.2R2-S3, * from 24.4 before 24.4R2-S1, * from 25.2 before 25.2R1-S1, 25.2R2.
An Improper Handling of Exceptional Conditions vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on SRX Series allows an unauthenticated network-based attacker sending a specific ICMP packet through a GRE tunnel to cause the PFE to crash and restart. When PowerMode IPsec (PMI) and GRE performance acceleration are enabled and the device receives a specific ICMP packet, a crash occurs in the SRX PFE, resulting in traffic loss. PMI is enabled by default, and GRE performance acceleration can be enabled by running the configuration command shown below. PMI is a mode of operation that provides IPsec performance improvements using Vector Packet Processing. Note that PMI with GRE performance acceleration is only supported on specific SRX platforms. This issue affects Junos OS on the SRX Series: * all versions before 21.4R3-S12, * from 22.4 before 22.4R3-S8, * from 23.2 before 23.2R2-S5, * from 23.4 before 23.4R2-S5, * from 24.2 before 24.2R2-S3, * from 24.4 before 24.4R2-S1, * from 25.2 before 25.2R1-S1, 25.2R2.
An Incorrect Initialization of Resource vulnerability in the Internal Device Manager (IDM) of Juniper Networks Junos OS on EX4000 models allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). On EX4000 models with 48 ports (EX4000-48T, EX4000-48P, EX4000-48MP) a high volume of traffic destined to the device will cause an FXPC crash and restart, which leads to a complete service outage until the device has automatically restarted. The following reboot reason can be seen in the output of 'show chassis routing-engine' and as a log message: reason=0x4000002 reason_string=0x4000002:watchdog + panic with core dump This issue affects Junos OS on EX4000-48T, EX4000-48P and EX4000-48MP: * 24.4 versions before 24.4R2, * 25.2 versions before 25.2R1-S2, 25.2R2. This issue does not affect versions before 24.4R1 as the first Junos OS version for the EX4000 models was 24.4R1.
An Improper Locking vulnerability in the GTP plugin of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (Dos). If an SRX Series device receives a specifically malformed GPRS Tunnelling Protocol (GTP) Modify Bearer Request message, a lock is acquired and never released. This results in other threads not being able to acquire a lock themselves, causing a watchdog timeout leading to FPC crash and restart. This issue leads to a complete traffic outage until the device has automatically recovered. This issue affects Junos OS on SRX Series: * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5, * 23.4 versions before 23.4R2-S6, * 24.2 versions before 24.2R2-S3, * 24.4 versions before 24.4R2-S2, * 25.2 versions before 25.2R1-S1, 25.2R2.
An Improper Validation of Syntactic Correctness of Input vulnerability in the Web-Filtering module of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If an SRX device configured for UTM Web-Filtering receives a specifically malformed SSL packet, this will cause an FPC crash and restart. This issue affects Junos OS on SRX Series: * 23.2 versions from 23.2R2-S2 before 23.2R2-S5, * 23.4 versions from 23.4R2-S1 before 23.4R2-S5, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R1-S3, 24.4R2. Earlier versions of Junos are also affected, but no fix is available.
A Double Free vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX and MX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). On all SRX and MX Series platforms, when during TCP session establishment a specific sequence of packets is encountered a double free happens. This causes flowd to crash and the respective FPC to restart. This issue affects Junos OS on SRX and MX Series: * all versions before 22.4R3-S7, * 23.2 versions before 23.2R2-S3, * 23.4 versions before 23.4R2-S4, * 24.2 versions before 24.2R2.
An Unchecked Return Value vulnerability in the DNS module of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If an SRX Series device configured for DNS processing, receives a specifically formatted DNS request flowd will crash and restart, which causes a service interruption until the process has recovered. This issue affects Junos OS on SRX Series: * 23.4 versions before 23.4R2-S5, * 24.2 versions before 24.2R2-S1, * 24.4 versions before 24.4R2. This issue does not affect Junos OS versions before 23.4R1.
An Improper Validation of Array Index vulnerability in the SIP ALG of Juniper Networks Junos OS on SRX 5000 Series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an attacker sends an SIP packets with a malformed SDP field then the SIP ALG can not process it which will lead to an FPC crash and restart. Continued receipt of these specific packets will lead to a sustained Denial of Service. This issue can only occur when both below mentioned conditions are fulfilled: 1. Call distribution needs to be enabled: [security alg sip enable-call-distribution] 2. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX, and MX with SPC3 use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX 5000 Series: 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R1-S1, 22.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.
An Improper Handling of Unexpected Data Type vulnerability in the handling of SIP calls in Juniper Networks Junos OS on SRX Series and MX Series platforms allows an attacker to cause a memory leak leading to Denial of Services (DoS). This issue occurs on all MX Series platforms with MS-MPC or MS-MIC card and all SRX Series platforms where SIP ALG is enabled. Successful exploitation of this vulnerability prevents additional SIP calls and applications from succeeding. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.1 versions 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2, 22.1R3-S1. This issue does not affect Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 18.2R1.
An Improper Check for Unusual or Exceptional Conditions vulnerability in BGP route processing of Juniper Networks Junos OS and Junos OS Evolved allows an attacker to cause Routing Protocol Daemon (RPD) crash by sending a BGP route with invalid next-hop resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems without import policy configured. This issue affects: Juniper Networks Junos OS 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. Juniper Networks Junos OS Evolved 21.4-EVO versions prior to 21.4R2-S2-EVO, 21.4R3-EVO; 22.1-EVO versions prior to 22.1R1-S2-EVO, 22.1R2-EVO; 22.2-EVO versions prior to 22.2R1-S1-EVO, 22.2R2-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 21.1R1. Juniper Networks Junos OS Evolved versions prior to 21.3R1-EVO.
A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Networks Junos OS on MX Series platforms with MPC10/MPC11 line cards, allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). Devices are only vulnerable when the Suspicious Control Flow Detection (scfd) feature is enabled. Upon enabling this specific feature, an attacker sending specific traffic is causing memory to be allocated dynamically and it is not freed. Memory is not freed even after deactivating this feature. Sustained processing of such traffic will eventually lead to an out of memory condition that prevents all services from continuing to function, and requires a manual restart to recover. The FPC memory usage can be monitored using the CLI command "show chassis fpc". On running the above command, the memory of AftDdosScfdFlow can be observed to detect the memory leak. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 20.2R3-S5; 20.3 version 20.3R1 and later versions.
When sFlow is enabled and it monitors a packet forwarded via ECMP, a buffer management vulnerability in the dcpfe process of Juniper Networks Junos OS on QFX10K Series systems allows an attacker to cause the Packet Forwarding Engine (PFE) to crash and restart by sending specific genuine packets to the device, resulting in a Denial of Service (DoS) condition. The dcpfe process tries to copy more data into a smaller buffer, which overflows and corrupts the buffer, causing a crash of the dcpfe process. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX10K Series: All versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R1-S2, 22.2R2.
An Improper Locking vulnerability in the SIP ALG of Juniper Networks Junos OS on MX Series with MS-MPC or MS-MIC card and SRX Series allows an unauthenticated, network-based attacker to cause a flow processing daemon (flowd) crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue occurs when SIP ALG is enabled and specific SIP messages are processed simultaneously. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on MX Series, or SRX Series.
An Allocation of Resources Without Limits or Throttling vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On QFX10K Series, Inter-Chassis Control Protocol (ICCP) is used in MC-LAG topologies to exchange control information between the devices in the topology. ICCP connection flaps and sync issues will be observed due to excessive specific traffic to the local device. This issue affects Juniper Networks Junos OS on QFX10K Series: * All versions prior to 20.2R3-S7; * 20.4 versions prior to 20.4R3-S4; * 21.1 versions prior to 21.1R3-S3; * 21.2 versions prior to 21.2R3-S1; * 21.3 versions prior to 21.3R3; * 21.4 versions prior to 21.4R3; * 22.1 versions prior to 22.1R2.
An Uncontrolled Resource Consumption vulnerability in TCP processing on the Routing Engine (RE) of Juniper Networks Junos OS allows an unauthenticated network-based attacker to send crafted TCP packets destined to the device, resulting in an MBUF leak that ultimately leads to a Denial of Service (DoS). The system does not recover automatically and must be manually restarted to restore service. This issue occurs when crafted TCP packets are sent directly to a configured IPv4 or IPv6 interface on the device. Transit traffic will not trigger this issue. MBUF usage can be monitored through the use of the 'show system buffers' command. For example: user@junos> show system buffers | refresh 5 4054/566/4620 mbufs in use (current/cache/total) ... 4089/531/4620 mbufs in use (current/cache/total) ... 4151/589/4740 mbufs in use (current/cache/total) ... 4213/527/4740 mbufs in use (current/cache/total) This issue affects Juniper Networks Junos OS: 12.3 version 12.3R12-S19 and later versions; 15.1 version 15.1R7-S10 and later versions; 17.3 version 17.3R3-S12 and later versions; 18.4 version 18.4R3-S9 and later versions; 19.1 version 19.1R3-S7 and later versions; 19.2 version 19.2R3-S3 and later versions; 19.3 version 19.3R2-S7, 19.3R3-S3 and later versions prior to 19.3R3-S7; 19.4 version 19.4R2-S7, 19.4R3-S5 and later versions prior to 19.4R3-S10; 20.1 version 20.1R3-S1 and later versions; 20.2 version 20.2R3-S2 and later versions prior to 20.2R3-S6; 20.3 version 20.3R3-S1 and later versions prior to 20.3R3-S6; 20.4 version 20.4R2-S2, 20.4R3 and later versions prior to 20.4R3-S5; 21.1 version 21.1R2 and later versions prior to 21.1R3-S4; 21.2 version 21.2R1-S1, 21.2R2 and later versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2; 22.3 versions prior to 22.3R1-S1, 22.3R2.
A vulnerability in class-of-service (CoS) queue management in Juniper Networks Junos OS on the ACX2K Series devices allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). Specific packets are being incorrectly routed to a queue used for other high-priority traffic such as BGP, PIM, ICMP, ICMPV6 ND and ISAKMP. Due to this misclassification of traffic, receipt of a high rate of these specific packets will cause delays in the processing of other traffic, leading to a Denial of Service (DoS). Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX2K Series: All versions prior to 19.4R3-S9; All 20.2 versions; 20.3 versions prior to 20.3R3-S6 on ACX2K Series; 20.4 versions prior to 20.4R3-S4 on ACX2K Series; All 21.1 versions; 21.2 versions prior to 21.2R3-S3 on ACX2K Series. Note: This issues affects legacy ACX2K Series PPC-based devices. This platform reached Last Supported Version (LSV) as of the Junos OS 21.2 Release.
A Buffer Overflow vulnerability in SIP ALG of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On all MX Series and SRX Series platform with SIP ALG enabled, when a malformed SIP packet is received, the flow processing daemon (flowd) will crash and restart. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on SRX Series.
An Out-of-Bounds Write vulnerability in the H.323 ALG of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all MX Series and SRX Series platform, when H.323 ALG is enabled and specific H.323 packets are received simultaneously, a flow processing daemon (flowd) crash will occur. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series All versions prior to 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2.
A Missing Release of Memory after Effective Lifetime vulnerability in the Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In an IPsec VPN environment, a memory leak will be seen if a DH or ECDH group is configured. Eventually the flowd process will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.
An Improper Validation of Array Index vulnerability in the Advanced Forwarding Toolkit Manager daemon (aftmand) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On the PTX10008 and PTX10016 platforms running Junos OS or Junos OS Evolved, when a specific SNMP MIB is queried this will cause a PFE crash and the FPC will go offline and not automatically recover. A system restart is required to get the affected FPC in an operational state again. This issue affects: Juniper Networks Junos OS 22.1 version 22.1R2 and later versions; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. Juniper Networks Junos OS Evolved 21.3-EVO version 21.3R3-EVO and later versions; 21.4-EVO version 21.4R1-S2-EVO, 21.4R2-EVO and later versions prior to 21.4R2-S1-EVO; 22.1-EVO version 22.1R2-EVO and later versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R1-S1-EVO, 22.2R2-EVO.
An Uncontrolled Resource Consumption vulnerability in the PFE management daemon (evo-pfemand) of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause an FPC crash leading to a Denial of Service (DoS). When a specific SNMP GET operation or a specific CLI command is executed this will cause a GUID resource leak, eventually leading to exhaustion and result in an FPC crash and reboot. GUID exhaustion will trigger a syslog message like one of the following for example: evo-pfemand[<pid>]: get_next_guid: Ran out of Guid Space ... evo-aftmand-zx[<pid>]: get_next_guid: Ran out of Guid Space ... This leak can be monitored by running the following command and taking note of the value in the rightmost column labeled Guids: user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3448 0 3448 re0 evo-pfemand net::juniper::interfaces::IFLId 0 561 0 561 user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3784 0 3784 re0 evo-pfemand net::juniper::interfaces::IFLId 0 647 0 647 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S3-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO versions prior to 21.2R3-S4-EVO; 21.3-EVO version 21.3R1-EVO and later versions; 21.4-EVO versions prior to 21.4R2-EVO.
An Out-of-Bounds Write vulnerability in Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On SRX Series devices using Unified Policies with IPv6, when a specific IPv6 packet goes through a dynamic-application filter which will generate an ICMP deny message, the flowd core is observed and the PFE is restarted. This issue affects: Juniper Networks Junos OS on SRX Series: 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.
A Reachable Assertion vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows to send specific genuine PIM packets to the device resulting in rpd to crash causing a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Note: This issue is not noticed when all the devices in the network are Juniper devices. This issue affects Juniper Networks: Junos OS: * All versions prior to 20.4R3-S7; * 21.2 versions prior to 21.2R3-S5; * 21.3 versions prior to 21.3R3-S4; * 21.4 versions prior to 21.4R3-S4; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3; * 22.3 versions prior to 22.3R3; * 22.4 versions prior to 22.4R3. Junos OS Evolved: * All versions prior to 22.3R3-EVO; * 22.4-EVO versions prior to 22.4R3-EVO; * 23.2-EVO versions prior to 23.2R1-EVO.
An Improper Check or Handling of Exceptional Conditions vulnerability in the IPsec library of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause Denial of Service (DoS). On all MX platforms with MS-MPC or MS-MIC card, when specific IPv4 packets are processed by an IPsec6 tunnel, the Multiservices PIC Management Daemon (mspmand) process will core and restart. This will lead to FPC crash. Traffic flow is impacted while mspmand restarts. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue only occurs if an IPv4 address is not configured on the multiservice interface. This issue affects: Juniper Networks Junos OS on MX Series All versions prior to 19.4R3-S9; 20.1 version 20.1R3-S5 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2.
An Improper Handling of Inconsistent Special Elements vulnerability in the Junos Services Framework (jsf) module of Juniper Networks Junos OS allows an unauthenticated network based attacker to cause a crash in the Packet Forwarding Engine (pfe) and thereby resulting in a Denial of Service (DoS). Upon receiving malformed SSL traffic, the PFE crashes. A manual restart will be needed to recover the device. This issue only affects devices with Juniper Networks Advanced Threat Prevention (ATP) Cloud enabled with Encrypted Traffic Insights (configured via ‘security-metadata-streaming policy’). This issue affects Juniper Networks Junos OS: * All versions prior to 20.4R3-S8, 20.4R3-S9; * 21.1 version 21.1R1 and later versions; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S5; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3-S2; * 22.3 versions prior to 22.3R2-S2, 22.3R3; * 22.4 versions prior to 22.4R2-S1, 22.4R3;
An improper interpretation conflict of certain data between certain software components within the Juniper Networks Junos OS devices does not allow certain traffic to pass through the device upon receipt from an ingress interface filtering certain specific types of traffic which is then being redirected to an egress interface on a different VLAN. This causes a Denial of Service (DoS) to those clients sending these particular types of traffic. Such traffic being sent by a client may appear genuine, but is non-standard in nature and should be considered as potentially malicious, and can be targeted to the device, or destined through it for the issue to occur. This issues affects IPv4 and IPv6 traffic. An indicator of compromise may be found by checking log files. You may find that traffic on the input interface has 100% of traffic flowing into the device, yet the egress interface shows 0 pps leaving the device. For example: [show interfaces "interface" statistics detail] Output between two interfaces would reveal something similar to: Ingress, first interface: -------------------- Interface Link Input packets (pps) Output packets (pps) et-0/0/0 Up 9999999999 (9999) 1 (0) -------------------- Egress, second interface: -------------------- Interface Link Input packets (pps) Output packets (pps) et-0/0/1 Up 0 (0) 9999999999 (0) -------------------- Dropped packets will not show up in DDoS monitoring/protection counters as issue is not caused by anti-DDoS protection mechanisms. This issue affects: Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S7 on NFX250, QFX5K Series, EX4600; 17.4 versions prior to 17.4R2-S11, 17.4R3-S3 on NFX250, QFX5K Series, EX4600; 18.1 versions prior to 18.1R3-S9 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4600; 18.2 versions prior to 18.2R3-S3 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600; 18.3 versions prior to 18.3R3-S1 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 18.4 versions prior to 18.4R1-S5, 18.4R2-S3, 18.4R3 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 19.2 versions prior to 19.2R1-S5, 19.2R2 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 19.3 versions prior to 19.3R2-S3, 19.3R3 on NFX250, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series; 19.4 versions prior to 19.4R1-S2, 19.4R2 on NFX250, NFX350, QFX5K Series, EX2300 Series, EX3400 Series, EX4300 Multigigabit, EX4600 Series. This issue does not affect Junos OS releases prior to 17.2R2.
On Juniper Networks SRX Series devices with link aggregation (lag) configured, executing any operation that fetches Aggregated Ethernet (AE) interface statistics, including but not limited to SNMP GET requests, causes a slow kernel memory leak. If all the available memory is consumed, the traffic will be impacted and a reboot might be required. The following log can be seen if this issue happens. /kernel: rt_pfe_veto: Memory over consumed. Op 1 err 12, rtsm_id 0:-1, msg type 72 /kernel: rt_pfe_veto: free kmem_map memory = (20770816) curproc = kmd An administrator can use the following CLI command to monitor the status of memory consumption (ifstat bucket): user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 2588977 162708K - 19633958 <<<< user@device > show system virtual-memory no-forwarding | match ifstat Type InUse MemUse HighUse Limit Requests Limit Limit Size(s) ifstat 3021629 189749K - 22914415 <<<< This issue affects Juniper Networks Junos OS on SRX Series: 17.1 versions 17.1R3 and above prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S5; 18.2 versions prior to 18.2R3-S7, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS prior to 17.1R3.
A Missing Release of Memory after Effective Lifetime vulnerability in the routing protocol daemon of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). In a BGP rib sharding scenario, when an attribute of an active BGP route is updated memory will leak. As rpd memory usage increases over time the rpd process will eventually run out of memory, crash, and restart. The memory utilization can be monitored with the following CLI commands: show task memory show system processes extensive | match rpd This issue affects: Juniper Networks Junos OS 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2. Juniper Networks Junos OS Evolved 20.3-EVO version 20.3R1-EVO and later versions; 20.4-EVO versions prior to 20.4R3-S6-EVO; 21.2-EVO versions prior to 21.2R3-EVO; 21.3-EVO versions prior to 21.3R2-EVO.
An Improper Validation of Syntactic Correctness of Input vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On all Junos OS MX Series and SRX Series platforms, when SIP ALG is enabled, and a specific SIP packet is received and processed, NAT IP allocation fails for genuine traffic, which causes Denial of Service (DoS). Continuous receipt of this specific SIP ALG packet will cause a sustained DoS condition. NAT IP usage can be monitored by running the following command. user@srx> show security nat resource-usage source-pool <source_pool_name> Pool name: source_pool_name .. Address Factor-index Port-range Used Avail Total Usage X.X.X.X 0 Single Ports 50258 52342 62464 96% <<<<< - Alg Ports 0 2048 2048 0% This issue affects: Juniper Networks Junos OS on MX Series and SRX Series * All versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.
A Buffer Over-read vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). When an affected device receives a BGP update with a set of specific optional transitive attributes over an established peering session, rpd will crash and restart when attempting to advertise the received information to another peer. This issue can only happen if one or both of the BGP peers of the receiving session are non-4-byte-AS capable as determined from the advertised capabilities during BGP session establishment. Junos OS and Junos OS Evolved default behavior is 4-byte-AS capable unless this has been specifically disabled by configuring: [ protocols bgp ... disable-4byte-as ] Established BGP sessions can be checked by executing: show bgp neighbor <IP address> | match "4 byte AS" This issue affects: Junos OS: * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5, * 23.4 versions before 23.4R2-S6, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R2; Junos OS Evolved: * all versions before 22.4R3-S8-EVO, * 23.2 versions before 23.2R2-S5-EVO, * 23.4 versions before 23.4R2-S6-EVO, * 24.2 versions before 24.2R2-S2-EVO, * 24.4 versions before 24.4R2-EVO.
A Use of Uninitialized Resource vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX4700 devices allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When forwarding-options sampling is enabled, receipt of any traffic destined to the Routing Engine (RE) by the PFE line card leads to an FPC crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of any traffic leading to the RE by the PFE line card will create a sustained Denial of Service (DoS) condition to the PFE line card. This issue affects Junos OS on SRX4700: * from 24.4 before 24.4R1-S3, 24.4R2 This issue affects IPv4 and IPv6.