The Bluetooth Low Energy implementation on STMicroelectronics BLE Stack through 1.3.1 for STM32WB5x devices does not properly handle consecutive Attribute Protocol (ATT) requests on reception, allowing attackers in radio range to cause an event deadlock or crash via crafted packets.

A vulnerability has been identified in MS/TP Point Pickup Module (All versions). Affected devices improperly handle specific incoming BACnet MSTP messages. This could allow an attacker residing in the same BACnet network to send a specially crafted MSTP message that results in a denial of service condition of the targeted device. A power cycle is required to restore the device's normal operation.

A vulnerability in the handling of Inter-Access Point Protocol (IAPP) messages by Cisco Wireless LAN Controller (WLC) Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. The vulnerability exist because the software improperly validates input on fields within IAPP messages. An attacker could exploit the vulnerability by sending malicious IAPP messages to an affected device. A successful exploit could allow the attacker to cause the Cisco WLC Software to reload, resulting in a DoS condition. Software versions prior to 8.2.170.0, 8.5.150.0, and 8.8.100.0 are affected.

A vulnerability in the handling of Inter-Access Point Protocol (IAPP) messages by Cisco Wireless LAN Controller (WLC) Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. The vulnerability exist because the software improperly validates input on fields within IAPP messages. An attacker could exploit the vulnerability by sending malicious IAPP messages to an affected device. A successful exploit could allow the attacker to cause the Cisco WLC Software to reload, resulting in a DoS condition. Software versions prior to 8.2.170.0, 8.5.150.0, and 8.8.100.0 are affected.

Improper input validation for some Intel(R) PROSet/Wireless and Intel(R) Killer(TM) Wi-Fi software before version 22.240 may allow an unauthenticated user to potentially enable denial of service via adjacent access.

CWE-20: Improper Input Validation vulnerability exists that could cause Denial-of-Service of the product when malicious ICMPV6 packets are sent to the device.

A vulnerability in the bridge protocol data unit (BPDU) forwarding functionality of Cisco Aironet Access Points (APs) could allow an unauthenticated, adjacent attacker to cause an AP port to go into an error disabled state. The vulnerability occurs because BPDUs received from specific wireless clients are forwarded incorrectly. An attacker could exploit this vulnerability on the wireless network by sending a steady stream of crafted BPDU frames. A successful exploit could allow the attacker to cause a limited denial of service (DoS) attack because an AP port could go offline.

CWE-20: Improper Input Validation vulnerability exists that could cause Denial-of-Service of the product when malicious IPV6 packets are sent to the device.

A vulnerability has been identified in SCALANCE W1788-1 M12 (All versions < V3.0.0), SCALANCE W1788-2 EEC M12 (All versions < V3.0.0), SCALANCE W1788-2 M12 (All versions < V3.0.0), SCALANCE W1788-2IA M12 (All versions < V3.0.0). Affected devices do not properly handle malformed TCP packets received over the RemoteCapture feature. This could allow an attacker to lead to a denial of service condition which only affects the port used by the RemoteCapture feature.

The client 802.11 mac implementation in Espressif ESP8266_NONOS_SDK 2.2.0 through 3.1.0 does not validate correctly the RSN AuthKey suite list count in beacon frames, probe responses, and association responses, which allows attackers in radio range to cause a denial of service (crash) via a crafted message.

No proper validation of the length of user input in olcp_ind_handler in zephyr/subsys/bluetooth/services/ots/ots_client.c.

BT: Missing length checks of net_buf in rfcomm_handle_data

BT: HCI: adv_ext_report Improper discarding in adv_ext_report

BT: Classic: SDP OOB access in get_att_search_list

BT: Unchecked user input in bap_broadcast_assistant

A vulnerability has been identified in SIMATIC S7-400 CPU 414-3 PN/DP V7 (All versions < V7.0.3), SIMATIC S7-400 CPU 414F-3 PN/DP V7 (All versions < V7.0.3), SIMATIC S7-400 CPU 416-3 PN/DP V7 (All versions < V7.0.3), SIMATIC S7-400 CPU 416F-3 PN/DP V7 (All versions < V7.0.3), SIMATIC CP 343-1 (incl. SIPLUS variants) (All versions), SIMATIC CP 343-1 Advanced (incl. SIPLUS variants) (All versions), SIMATIC CP 443-1 (All versions < V3.3), SIMATIC CP 443-1 (All versions < V3.3), SIMATIC CP 443-1 Advanced (All versions < V3.3), SIMATIC ET 200pro IM154-8 PN/DP CPU (All versions < V3.2.16), SIMATIC ET 200pro IM154-8F PN/DP CPU (All versions < V3.2.16), SIMATIC ET 200pro IM154-8FX PN/DP CPU (All versions < V3.2.16), SIMATIC ET 200S IM151-8 PN/DP CPU (All versions < V3.2.16), SIMATIC ET 200S IM151-8F PN/DP CPU (All versions < V3.2.16), SIMATIC S7-1500 CPU family (incl. related ET200 CPUs and SIPLUS variants) (All versions < V1.7.0), SIMATIC S7-1500 Software Controller (All versions < V1.7.0), SIMATIC S7-300 CPU 314C-2 PN/DP (All versions < V3.3.16), SIMATIC S7-300 CPU 315-2 PN/DP (All versions < V3.2.16), SIMATIC S7-300 CPU 315F-2 PN/DP (All versions < V3.2.16), SIMATIC S7-300 CPU 315T-3 PN/DP (All versions < V3.2.16), SIMATIC S7-300 CPU 317-2 PN/DP (All versions < V3.2.16), SIMATIC S7-300 CPU 317F-2 PN/DP (All versions < V3.2.16), SIMATIC S7-300 CPU 317T-3 PN/DP (All versions < V3.2.16), SIMATIC S7-300 CPU 317TF-3 PN/DP (All versions < V3.2.16), SIMATIC S7-300 CPU 319-3 PN/DP (All versions < V3.2.16), SIMATIC S7-300 CPU 319F-3 PN/DP (All versions < V3.2.16), SIMATIC S7-400 CPU 412-2 PN V7 (All versions < V7.0.3), SIMATIC S7-400 H V6 CPU family (incl. SIPLUS variants) (All versions < V6.0.9), SIMATIC S7-400 PN/DP V6 CPU family (incl. SIPLUS variants) (All versions < V6.0.7), SIMATIC S7-410 CPU family (incl. SIPLUS variants) (All versions < V8.1), SIMATIC WinAC RTX 2010 (All versions < V2010 SP3), SIMATIC WinAC RTX F 2010 (All versions < V2010 SP3), SINUMERIK 828D (All versions < V4.7 SP6 HF1), SIPLUS ET 200S IM151-8 PN/DP CPU (All versions < V3.2.16), SIPLUS ET 200S IM151-8F PN/DP CPU (All versions < V3.2.16), SIPLUS NET CP 443-1 (All versions < V3.3), SIPLUS NET CP 443-1 Advanced (All versions < V3.3), SIPLUS S7-300 CPU 314C-2 PN/DP (All versions < V3.3.16), SIPLUS S7-300 CPU 315-2 PN/DP (All versions < V3.2.16), SIPLUS S7-300 CPU 315F-2 PN/DP (All versions < V3.2.16), SIPLUS S7-300 CPU 317-2 PN/DP (All versions < V3.2.16), SIPLUS S7-300 CPU 317F-2 PN/DP (All versions < V3.2.16), SIPLUS S7-400 CPU 414-3 PN/DP V7 (All versions < V7.0.3), SIPLUS S7-400 CPU 416-3 PN/DP V7 (All versions < V7.0.3), Softnet PROFINET IO for PC-based Windows systems (All versions). Responding to a PROFINET DCP request with a specially crafted PROFINET DCP packet could cause a denial of service condition of the requesting system. The security vulnerability could be exploited by an attacker located on the same Ethernet segment (OSI Layer 2) as the targeted device. A manual restart is required to recover the system.

Windows Mobile Broadband Driver Denial of Service Vulnerability

Windows Mobile Broadband Driver Denial of Service Vulnerability

Windows Mobile Broadband Driver Denial of Service Vulnerability

The setup_cifs_sb function in fs/cifs/connect.c in the Linux kernel before 2.6.39 does not properly handle DFS referrals, which allows remote CIFS servers to cause a denial of service (system crash) by placing a referral at the root of a share.

Certain NETGEAR devices are affected by denial of service. This affects GS110EMX before 1.0.0.9, GS810EMX before 1.0.0.5, XS512EM before 1.0.0.6, and XS724EM before 1.0.0.6.

A Improper Validation of Specified Index, Position, or Offset in Input vulnerability in the Juniper DHCP daemon (jdhcpd) of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a crash of jdhcpd and thereby a Denial of Service (DoS). In a scenario where DHCP relay or local server is configured the problem can be triggered if a DHCPv4 packet with specific options is received leading to a corruption of the options read from the packet. This corruption can then lead to jdhcpd crash and restart. This issue affects: Juniper Networks Junos OS 17.4R1 and later versions prior to 18.4R3-S10; 19.1 versions prior to 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R2-S2, 21.1R3; 21.2 versions prior to 21.2R1-S2, 21.2R2, 21.2R3; 21.3 versions prior to 21.3R1-S1, 21.3R2.

An Improper Validation of Syntactic Correctness of Input vulnerability in the Juniper DHCP daemon (jdhcpd) of Juniper Networks Junos OS allows an adjacent unauthenticated attacker sending a malformed DHCP packet to cause a crash of jdhcpd and thereby a Denial of Service (DoS). If option-82 is configured in a DHCP snooping / -security scenario, jdhcpd crashes if a specific malformed DHCP request packet is received. The DHCP functionality is impacted while jdhcpd restarts, and continued exploitation of the vulnerability will lead to the unavailability of the DHCP service and thereby a sustained DoS. This issue affects Juniper Networks Junos OS 13.2 version 13.2R1 and later versions prior to 15.1R7-S11; 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R3-S6; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue does not affect Juniper Networks Junos OS version 12.3R12 and prior versions.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent unauthenticated attacker to cause DoS (Denial of Service). If another router generates more than one specific valid OSPFv3 LSA then rpd will crash while processing these LSAs. This issue only affects systems configured with OSPFv3, while OSPFv2 is not affected. This issue affects: Juniper Networks Junos OS 19.2 versions prior to 19.2R3-S6; 19.3 version 19.3R2 and later versions; 19.4 versions prior to 19.4R2-S8, 19.4R3-S9; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S5-EVO; 21.1-EVO versions prior to 21.1R3-S2-EVO; 21.2-EVO versions prior to 21.2R3-S1-EVO; 21.3-EVO versions prior to 21.3R3-S2-EVO; 21.4-EVO versions prior to 21.4R2-EVO; 22.1-EVO versions prior to 22.1R2-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS 19.2 versions prior to 19.2R2.

On QFX10000 Series devices using Juniper Networks Junos OS when configured as transit IP/MPLS penultimate hop popping (PHP) nodes with link aggregation group (LAG) interfaces, an Improper Validation of Specified Index, Position, or Offset in Input weakness allows an attacker sending certain IP packets to cause multiple interfaces in the LAG to detach causing a Denial of Service (DoS) condition. Continued receipt and processing of these packets will sustain the Denial of Service. This issue affects IPv4 and IPv6 packets. Packets of either type can cause and sustain the DoS event. These packets can be destined to the device or be transit packets. On devices such as the QFX10008 with line cards, line cards can be restarted to restore service. On devices such as the QFX10002 you can restart the PFE service, or reboot device to restore service. This issue affects: Juniper Networks Junos OS on QFX10000 Series: All versions prior to 15.1R7-S11; 18.4 versions prior to 18.4R2-S10, 18.4R3-S10; 19.1 versions prior to 19.1R3-S8; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S1. An indicator of compromise may be seen by issuing the command: request pfe execute target fpc0 command "show jspec pechip[3] registers ps l2_node 10" timeout 0 | refresh 1 | no-more and reviewing for backpressured output; for example: GOT: 0x220702a8 pe.ps.l2_node[10].pkt_cnt 00000076 GOT: 0x220702b4 pe.ps.l2_node[10].backpressured 00000002 <<<< STICKS HERE and requesting detail on the pepic wanio: request pfe execute target fpc0 command "show pepic 0 wanio-info" timeout 0 | no-more | match xe-0/0/0:2 GOT: 3 xe-0/0/0:2 10 6 3 0 1 10 189 10 0x6321b088 <<< LOOK HERE as well as looking for tail drops looking at the interface queue, for example: show interfaces queue xe-0/0/0:2 resulting in: Transmitted: Total-dropped packets: 1094137 0 pps << LOOK HERE

An Improper Input Validation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent attacker to cause a PFE crash and thereby a Denial of Service (DoS). An FPC will crash and reboot after receiving a specific transit IPv6 packet over MPLS. Continued receipt of this packet will create a sustained Denial of Service (DoS) condition. This issue does not affect systems configured for IPv4 only. This issue affects: Juniper Networks Junos OS All versions prior to 12.3R12-S21; 15.1 versions prior to 15.1R7-S10; 17.3 versions prior to 17.3R3-S12; 18.3 versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S3-EVO; 21.2 versions prior to 21.2R3-EVO; 21.3 versions prior to 21.3R2-S1-EVO, 21.3R3-EVO; 21.4 versions prior to 21.4R2-EVO.

A vulnerability in the integrated wireless access point (AP) packet processing of the Cisco 1000 Series Connected Grid Router (CGR1K) could allow an unauthenticated, adjacent attacker to cause a denial of service condition on an affected device. This vulnerability is due to insufficient input validation of received traffic. An attacker could exploit this vulnerability by sending crafted traffic to an affected device. A successful exploit could allow the attacker to cause the integrated AP to stop processing traffic, resulting in a DoS condition. It may be necessary to manually reload the CGR1K to restore AP operation.

A vulnerability in the 802.11 association frame validation of Cisco Catalyst 9100 Series Access Points (APs) could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of certain parameters within association request frames received by the AP. An attacker could exploit this vulnerability by sending a crafted 802.11 association request to a nearby device. An exploit could allow the attacker to unexpectedly reload the device, resulting in a DoS condition.

Improper input validation for some Intel(R) PROSet/Wireless WiFi and Killer(TM) WiFi products may allow an unauthenticated user to potentially enable denial of service via adjacent access.

A vulnerability in the Cisco Discovery Protocol (formerly known as CDP) subsystem of devices running, or based on, Cisco NX-OS Software contain a vulnerability that could allow an unauthenticated, adjacent attacker to create a denial of service (DoS) condition. The vulnerability is due to a failure to properly validate certain fields within a Cisco Discovery Protocol message prior to processing it. An attacker with the ability to submit a Cisco Discovery Protocol message designed to trigger the issue could cause a DoS condition on an affected device while the device restarts. This vulnerability affects Firepower 4100 Series Next-Generation Firewall, Firepower 9300 Security Appliance, MDS 9000 Series Multilayer Director Switches, Nexus 1000V Series Switches, Nexus 1100 Series Cloud Services Platforms, Nexus 2000 Series Switches, Nexus 3000 Series Switches, Nexus 3500 Platform Switches, Nexus 3600 Platform Switches, Nexus 5500 Platform Switches, Nexus 5600 Platform Switches, Nexus 6000 Series Switches, Nexus 7000 Series Switches, Nexus 7700 Series Switches, Nexus 9000 Series Switches in NX-OS mode, Nexus 9500 R-Series Line Cards and Fabric Modules, UCS 6100 Series Fabric Interconnects, UCS 6200 Series Fabric Interconnects, UCS 6300 Series Fabric Interconnects. Cisco Bug IDs: CSCvc89242, CSCve40943, CSCve40953, CSCve40965, CSCve40970, CSCve40978, CSCve40992, CSCve41000, CSCve41007.

Patient Information Center iX (PIC iX) Versions C.02 and C.03 receives input or data, but does not validate or incorrectly validates that the input has the properties required to process the data safely and correctly.

In wifi driver, there is a possible system crash due to a missing validation check. This could lead to remote denial of service from a proximal attacker with no additional execution privileges needed. User interaction is not needed for exploitation. Patch ID: GN20190426015; Issue ID: GN20190426015.

Butter is a system usability utility. Due to a kernel error the JPNS kernel is being discontinued. Affected users are recommend to update to the Trinity kernel. There are no workarounds.

BT: Missing Check in LL_CONNECTION_UPDATE_IND Packet Leads to Division by Zero

Windows Mobile Broadband Driver Denial of Service Vulnerability

Windows Mobile Broadband Driver Denial of Service Vulnerability

Windows Mobile Broadband Driver Denial of Service Vulnerability

Improper Use of Validation Framework in firmware for some Intel(R) PROSet/Wireless Wi-Fi in multiple operating systems and some Killer(TM) Wi-Fi in Windows 10 and 11 may allow a unauthenticated user to potentially enable denial of service via adjacent access.

Improper input validation in firmware for Intel(R) PROSet/Wireless Wi-Fi in multiple operating systems and Killer(TM) Wi-Fi in Windows 10 and 11 may allow an unauthenticated user to potentially enable denial of service via adjacent access.

Improper Validation of Specified Index, Position, or Offset in Input in software for some Intel(R) PROSet/Wireless Wi-Fi in multiple operating systems and some Killer(TM) Wi-Fi in Windows 10 and 11 may allow an unauthenticated user to potentially enable denial of service via adjacent access.

Improper input validation in software for some Intel(R) PROSet/Wireless WiFi and Killer(TM) WiFi in Windows 10 may allow an unauthenticated user to potentially enable denial of service via adjacent access.

Improper input validation in software for Intel(R) PROSet/Wireless Wi-Fi and Killer(TM) Wi-Fi in Windows 10 and 11 may allow an unauthenticated user to potentially enable denial of service via adjacent access.

Improper input validation in firmware for some Intel(R) PROSet/Wireless Wi-Fi in multiple operating systems and some Killer(TM) Wi-Fi in Windows 10 and 11 may allow an unauthenticated user to potentially enable denial of service via adjacent access.

Improper Validation of Consistency within input in firmware for some Intel(R) PROSet/Wireless Wi-Fi in multiple operating systems and some Killer(TM) Wi-Fi in Windows 10 and 11 may allow a unauthenticated user to potentially enable denial of service via adjacent access.

Multiple vulnerabilities in the Control and Provisioning of Wireless Access Points (CAPWAP) protocol processing of Cisco IOS XE Software for Cisco Catalyst 9800 Series Wireless Controllers could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition of an affected device. These vulnerabilities are due to insufficient validation of CAPWAP packets. An attacker could exploit these vulnerabilities by sending a malformed CAPWAP packet to an affected device. A successful exploit could allow the attacker to cause the affected device to crash and reload, resulting in a DoS condition on the affected device.