In the Linux kernel, the following vulnerability has been resolved: ice: fix LAG and VF lock dependency in ice_reset_vf() 9f74a3dfcf83 ("ice: Fix VF Reset paths when interface in a failed over aggregate"), the ice driver has acquired the LAG mutex in ice_reset_vf(). The commit placed this lock acquisition just prior to the acquisition of the VF configuration lock. If ice_reset_vf() acquires the configuration lock via the ICE_VF_RESET_LOCK flag, this could deadlock with ice_vc_cfg_qs_msg() because it always acquires the locks in the order of the VF configuration lock and then the LAG mutex. Lockdep reports this violation almost immediately on creating and then removing 2 VF: ====================================================== WARNING: possible circular locking dependency detected 6.8.0-rc6 #54 Tainted: G W O ------------------------------------------------------ kworker/60:3/6771 is trying to acquire lock: ff40d43e099380a0 (&vf->cfg_lock){+.+.}-{3:3}, at: ice_reset_vf+0x22f/0x4d0 [ice] but task is already holding lock: ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&pf->lag_mutex){+.+.}-{3:3}: __lock_acquire+0x4f8/0xb40 lock_acquire+0xd4/0x2d0 __mutex_lock+0x9b/0xbf0 ice_vc_cfg_qs_msg+0x45/0x690 [ice] ice_vc_process_vf_msg+0x4f5/0x870 [ice] __ice_clean_ctrlq+0x2b5/0x600 [ice] ice_service_task+0x2c9/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 kthread+0x104/0x140 ret_from_fork+0x31/0x50 ret_from_fork_asm+0x1b/0x30 -> #0 (&vf->cfg_lock){+.+.}-{3:3}: check_prev_add+0xe2/0xc50 validate_chain+0x558/0x800 __lock_acquire+0x4f8/0xb40 lock_acquire+0xd4/0x2d0 __mutex_lock+0x9b/0xbf0 ice_reset_vf+0x22f/0x4d0 [ice] ice_process_vflr_event+0x98/0xd0 [ice] ice_service_task+0x1cc/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 kthread+0x104/0x140 ret_from_fork+0x31/0x50 ret_from_fork_asm+0x1b/0x30 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&pf->lag_mutex); lock(&vf->cfg_lock); lock(&pf->lag_mutex); lock(&vf->cfg_lock); *** DEADLOCK *** 4 locks held by kworker/60:3/6771: #0: ff40d43e05428b38 ((wq_completion)ice){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0 #1: ff50d06e05197e58 ((work_completion)(&pf->serv_task)){+.+.}-{0:0}, at: process_one_work+0x176/0x4d0 #2: ff40d43ea1960e50 (&pf->vfs.table_lock){+.+.}-{3:3}, at: ice_process_vflr_event+0x48/0xd0 [ice] #3: ff40d43ea1961210 (&pf->lag_mutex){+.+.}-{3:3}, at: ice_reset_vf+0xb7/0x4d0 [ice] stack backtrace: CPU: 60 PID: 6771 Comm: kworker/60:3 Tainted: G W O 6.8.0-rc6 #54 Hardware name: Workqueue: ice ice_service_task [ice] Call Trace: <TASK> dump_stack_lvl+0x4a/0x80 check_noncircular+0x12d/0x150 check_prev_add+0xe2/0xc50 ? save_trace+0x59/0x230 ? add_chain_cache+0x109/0x450 validate_chain+0x558/0x800 __lock_acquire+0x4f8/0xb40 ? lockdep_hardirqs_on+0x7d/0x100 lock_acquire+0xd4/0x2d0 ? ice_reset_vf+0x22f/0x4d0 [ice] ? lock_is_held_type+0xc7/0x120 __mutex_lock+0x9b/0xbf0 ? ice_reset_vf+0x22f/0x4d0 [ice] ? ice_reset_vf+0x22f/0x4d0 [ice] ? rcu_is_watching+0x11/0x50 ? ice_reset_vf+0x22f/0x4d0 [ice] ice_reset_vf+0x22f/0x4d0 [ice] ? process_one_work+0x176/0x4d0 ice_process_vflr_event+0x98/0xd0 [ice] ice_service_task+0x1cc/0x480 [ice] process_one_work+0x1e9/0x4d0 worker_thread+0x1e1/0x3d0 ? __pfx_worker_thread+0x10/0x10 kthread+0x104/0x140 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x31/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1b/0x30 </TASK> To avoid deadlock, we must acquire the LAG ---truncated---

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: qca: fix NULL-deref on non-serdev setup Qualcomm ROME controllers can be registered from the Bluetooth line discipline and in this case the HCI UART serdev pointer is NULL. Add the missing sanity check to prevent a NULL-pointer dereference when setup() is called for a non-serdev controller.

In the Linux kernel, the following vulnerability has been resolved: arm64: tlb: Fix TLBI RANGE operand KVM/arm64 relies on TLBI RANGE feature to flush TLBs when the dirty pages are collected by VMM and the page table entries become write protected during live migration. Unfortunately, the operand passed to the TLBI RANGE instruction isn't correctly sorted out due to the commit 117940aa6e5f ("KVM: arm64: Define kvm_tlb_flush_vmid_range()"). It leads to crash on the destination VM after live migration because TLBs aren't flushed completely and some of the dirty pages are missed. For example, I have a VM where 8GB memory is assigned, starting from 0x40000000 (1GB). Note that the host has 4KB as the base page size. In the middile of migration, kvm_tlb_flush_vmid_range() is executed to flush TLBs. It passes MAX_TLBI_RANGE_PAGES as the argument to __kvm_tlb_flush_vmid_range() and __flush_s2_tlb_range_op(). SCALE#3 and NUM#31, corresponding to MAX_TLBI_RANGE_PAGES, isn't supported by __TLBI_RANGE_NUM(). In this specific case, -1 has been returned from __TLBI_RANGE_NUM() for SCALE#3/2/1/0 and rejected by the loop in the __flush_tlb_range_op() until the variable @scale underflows and becomes -9, 0xffff708000040000 is set as the operand. The operand is wrong since it's sorted out by __TLBI_VADDR_RANGE() according to invalid @scale and @num. Fix it by extending __TLBI_RANGE_NUM() to support the combination of SCALE#3 and NUM#31. With the changes, [-1 31] instead of [-1 30] can be returned from the macro, meaning the TLBs for 0x200000 pages in the above example can be flushed in one shoot with SCALE#3 and NUM#31. The macro TLBI_RANGE_MASK is dropped since no one uses it any more. The comments are also adjusted accordingly.

In the Linux kernel, the following vulnerability has been resolved: aio: Fix null ptr deref in aio_complete() wakeup list_del_init_careful() needs to be the last access to the wait queue entry - it effectively unlocks access. Previously, finish_wait() would see the empty list head and skip taking the lock, and then we'd return - but the completion path would still attempt to do the wakeup after the task_struct pointer had been overwritten.

In the Linux kernel, the following vulnerability has been resolved: ACPICA: Revert "ACPICA: avoid Info: mapping multiple BARs. Your kernel is fine." Undo the modifications made in commit d410ee5109a1 ("ACPICA: avoid "Info: mapping multiple BARs. Your kernel is fine.""). The initial purpose of this commit was to stop memory mappings for operation regions from overlapping page boundaries, as it can trigger warnings if different page attributes are present. However, it was found that when this situation arises, mapping continues until the boundary's end, but there is still an attempt to read/write the entire length of the map, leading to a NULL pointer deference. For example, if a four-byte mapping request is made but only one byte is mapped because it hits the current page boundary's end, a four-byte read/write attempt is still made, resulting in a NULL pointer deference. Instead, map the entire length, as the ACPI specification does not mandate that it must be within the same page boundary. It is permissible for it to be mapped across different regions.

kernel/trace/ftrace.c in the Linux kernel before 2.6.35.5, when debugfs is enabled, does not properly handle interaction between mutex possession and llseek operations, which allows local users to cause a denial of service (NULL pointer dereference and outage of all function tracing files) via an lseek call on a file descriptor associated with the set_ftrace_filter file.

A NULL pointer dereference flaw was found in the az6027 driver in drivers/media/usb/dev-usb/az6027.c in the Linux Kernel. The message from user space is not checked properly before transferring into the device. This flaw allows a local user to crash the system or potentially cause a denial of service.

In the Linux kernel, the following vulnerability has been resolved: i2c: lpi2c: Avoid calling clk_get_rate during transfer Instead of repeatedly calling clk_get_rate for each transfer, lock the clock rate and cache the value. A deadlock has been observed while adding tlv320aic32x4 audio codec to the system. When this clock provider adds its clock, the clk mutex is locked already, it needs to access i2c, which in return needs the mutex for clk_get_rate as well.

In the Linux kernel, the following vulnerability has been resolved: Avoid hw_desc array overrun in dw-axi-dmac I have a use case where nr_buffers = 3 and in which each descriptor is composed by 3 segments, resulting in the DMA channel descs_allocated to be 9. Since axi_desc_put() handles the hw_desc considering the descs_allocated, this scenario would result in a kernel panic (hw_desc array will be overrun). To fix this, the proposal is to add a new member to the axi_dma_desc structure, where we keep the number of allocated hw_descs (axi_desc_alloc()) and use it in axi_desc_put() to handle the hw_desc array correctly. Additionally I propose to remove the axi_chan_start_first_queued() call after completing the transfer, since it was identified that unbalance can occur (started descriptors can be interrupted and transfer ignored due to DMA channel not being enabled).

In the Linux kernel, the following vulnerability has been resolved: powerpc/eeh: avoid possible crash when edev->pdev changes If a PCI device is removed during eeh_pe_report_edev(), edev->pdev will change and can cause a crash, hold the PCI rescan/remove lock while taking a copy of edev->pdev->bus.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: amd-pstate: fix memory leak on CPU EPP exit The cpudata memory from kzalloc() in amd_pstate_epp_cpu_init() is not freed in the analogous exit function, so fix that. [ rjw: Subject and changelog edits ]

In the Linux kernel, the following vulnerability has been resolved: vfio/pci: Init the count variable in collecting hot-reset devices The count variable is used without initialization, it results in mistakes in the device counting and crashes the userspace if the get hot reset info path is triggered.

In the Linux kernel, the following vulnerability has been resolved: iio: temperature: mlx90635: Fix ERR_PTR dereference in mlx90635_probe() When devm_regmap_init_i2c() fails, regmap_ee could be error pointer, instead of checking for IS_ERR(regmap_ee), regmap is checked which looks like a copy paste error.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix NULL pointer dereference in ocfs2_abort_trigger() bdev->bd_super has been removed and commit 8887b94d9322 change the usage from bdev->bd_super to b_assoc_map->host->i_sb. Since ocfs2 hasn't set bh->b_assoc_map, it will trigger NULL pointer dereference when calling into ocfs2_abort_trigger(). Actually this was pointed out in history, see commit 74e364ad1b13. But I've made a mistake when reviewing commit 8887b94d9322 and then re-introduce this regression. Since we cannot revive bdev in buffer head, so fix this issue by initializing all types of ocfs2 triggers when fill super, and then get the specific ocfs2 trigger from ocfs2_caching_info when access journal. [joseph.qi@linux.alibaba.com: v2]

In the Linux kernel, the following vulnerability has been resolved: ata: libata-core: Fix null pointer dereference on error If the ata_port_alloc() call in ata_host_alloc() fails, ata_host_release() will get called. However, the code in ata_host_release() tries to free ata_port struct members unconditionally, which can lead to the following: BUG: unable to handle page fault for address: 0000000000003990 PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 10 PID: 594 Comm: (udev-worker) Not tainted 6.10.0-rc5 #44 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:ata_host_release.cold+0x2f/0x6e [libata] Code: e4 4d 63 f4 44 89 e2 48 c7 c6 90 ad 32 c0 48 c7 c7 d0 70 33 c0 49 83 c6 0e 41 RSP: 0018:ffffc90000ebb968 EFLAGS: 00010246 RAX: 0000000000000041 RBX: ffff88810fb52e78 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff88813b3218c0 RDI: ffff88813b3218c0 RBP: ffff88810fb52e40 R08: 0000000000000000 R09: 6c65725f74736f68 R10: ffffc90000ebb738 R11: 73692033203a746e R12: 0000000000000004 R13: 0000000000000000 R14: 0000000000000011 R15: 0000000000000006 FS: 00007f6cc55b9980(0000) GS:ffff88813b300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000003990 CR3: 00000001122a2000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? page_fault_oops+0x15a/0x2f0 ? exc_page_fault+0x7e/0x180 ? asm_exc_page_fault+0x26/0x30 ? ata_host_release.cold+0x2f/0x6e [libata] ? ata_host_release.cold+0x2f/0x6e [libata] release_nodes+0x35/0xb0 devres_release_group+0x113/0x140 ata_host_alloc+0xed/0x120 [libata] ata_host_alloc_pinfo+0x14/0xa0 [libata] ahci_init_one+0x6c9/0xd20 [ahci] Do not access ata_port struct members unconditionally.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix ufshcd_abort_one racing issue When ufshcd_abort_one is racing with the completion ISR, the completed tag of the request's mq_hctx pointer will be set to NULL by ISR. Return success when request is completed by ISR because ufshcd_abort_one does not need to do anything. The racing flow is: Thread A ufshcd_err_handler step 1 ... ufshcd_abort_one ufshcd_try_to_abort_task ufshcd_cmd_inflight(true) step 3 ufshcd_mcq_req_to_hwq blk_mq_unique_tag rq->mq_hctx->queue_num step 5 Thread B ufs_mtk_mcq_intr(cq complete ISR) step 2 scsi_done ... __blk_mq_free_request rq->mq_hctx = NULL; step 4 Below is KE back trace. ufshcd_try_to_abort_task: cmd at tag 41 not pending in the device. ufshcd_try_to_abort_task: cmd at tag=41 is cleared. Aborting tag 41 / CDB 0x28 succeeded Unable to handle kernel NULL pointer dereference at virtual address 0000000000000194 pc : [0xffffffddd7a79bf8] blk_mq_unique_tag+0x8/0x14 lr : [0xffffffddd6155b84] ufshcd_mcq_req_to_hwq+0x1c/0x40 [ufs_mediatek_mod_ise] do_mem_abort+0x58/0x118 el1_abort+0x3c/0x5c el1h_64_sync_handler+0x54/0x90 el1h_64_sync+0x68/0x6c blk_mq_unique_tag+0x8/0x14 ufshcd_err_handler+0xae4/0xfa8 [ufs_mediatek_mod_ise] process_one_work+0x208/0x4fc worker_thread+0x228/0x438 kthread+0x104/0x1d4 ret_from_fork+0x10/0x20

In the Linux kernel, the following vulnerability has been resolved: drop_monitor: replace spin_lock by raw_spin_lock trace_drop_common() is called with preemption disabled, and it acquires a spin_lock. This is problematic for RT kernels because spin_locks are sleeping locks in this configuration, which causes the following splat: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 449, name: rcuc/47 preempt_count: 1, expected: 0 RCU nest depth: 2, expected: 2 5 locks held by rcuc/47/449: #0: ff1100086ec30a60 ((softirq_ctrl.lock)){+.+.}-{2:2}, at: __local_bh_disable_ip+0x105/0x210 #1: ffffffffb394a280 (rcu_read_lock){....}-{1:2}, at: rt_spin_lock+0xbf/0x130 #2: ffffffffb394a280 (rcu_read_lock){....}-{1:2}, at: __local_bh_disable_ip+0x11c/0x210 #3: ffffffffb394a160 (rcu_callback){....}-{0:0}, at: rcu_do_batch+0x360/0xc70 #4: ff1100086ee07520 (&data->lock){+.+.}-{2:2}, at: trace_drop_common.constprop.0+0xb5/0x290 irq event stamp: 139909 hardirqs last enabled at (139908): [<ffffffffb1df2b33>] _raw_spin_unlock_irqrestore+0x63/0x80 hardirqs last disabled at (139909): [<ffffffffb19bd03d>] trace_drop_common.constprop.0+0x26d/0x290 softirqs last enabled at (139892): [<ffffffffb07a1083>] __local_bh_enable_ip+0x103/0x170 softirqs last disabled at (139898): [<ffffffffb0909b33>] rcu_cpu_kthread+0x93/0x1f0 Preemption disabled at: [<ffffffffb1de786b>] rt_mutex_slowunlock+0xab/0x2e0 CPU: 47 PID: 449 Comm: rcuc/47 Not tainted 6.9.0-rc2-rt1+ #7 Hardware name: Dell Inc. PowerEdge R650/0Y2G81, BIOS 1.6.5 04/15/2022 Call Trace: <TASK> dump_stack_lvl+0x8c/0xd0 dump_stack+0x14/0x20 __might_resched+0x21e/0x2f0 rt_spin_lock+0x5e/0x130 ? trace_drop_common.constprop.0+0xb5/0x290 ? skb_queue_purge_reason.part.0+0x1bf/0x230 trace_drop_common.constprop.0+0xb5/0x290 ? preempt_count_sub+0x1c/0xd0 ? _raw_spin_unlock_irqrestore+0x4a/0x80 ? __pfx_trace_drop_common.constprop.0+0x10/0x10 ? rt_mutex_slowunlock+0x26a/0x2e0 ? skb_queue_purge_reason.part.0+0x1bf/0x230 ? __pfx_rt_mutex_slowunlock+0x10/0x10 ? skb_queue_purge_reason.part.0+0x1bf/0x230 trace_kfree_skb_hit+0x15/0x20 trace_kfree_skb+0xe9/0x150 kfree_skb_reason+0x7b/0x110 skb_queue_purge_reason.part.0+0x1bf/0x230 ? __pfx_skb_queue_purge_reason.part.0+0x10/0x10 ? mark_lock.part.0+0x8a/0x520 ... trace_drop_common() also disables interrupts, but this is a minor issue because we could easily replace it with a local_lock. Replace the spin_lock with raw_spin_lock to avoid sleeping in atomic context.

In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: allocate dummy checksums for zoned NODATASUM writes Shin'ichiro reported that when he's running fstests' test-case btrfs/167 on emulated zoned devices, he's seeing the following NULL pointer dereference in 'btrfs_zone_finish_endio()': Oops: general protection fault, probably for non-canonical address 0xdffffc0000000011: 0000 [#1] PREEMPT SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000088-0x000000000000008f] CPU: 4 PID: 2332440 Comm: kworker/u80:15 Tainted: G W 6.10.0-rc2-kts+ #4 Hardware name: Supermicro Super Server/X11SPi-TF, BIOS 3.3 02/21/2020 Workqueue: btrfs-endio-write btrfs_work_helper [btrfs] RIP: 0010:btrfs_zone_finish_endio.part.0+0x34/0x160 [btrfs] RSP: 0018:ffff88867f107a90 EFLAGS: 00010206 RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff893e5534 RDX: 0000000000000011 RSI: 0000000000000004 RDI: 0000000000000088 RBP: 0000000000000002 R08: 0000000000000001 R09: ffffed1081696028 R10: ffff88840b4b0143 R11: ffff88834dfff600 R12: ffff88840b4b0000 R13: 0000000000020000 R14: 0000000000000000 R15: ffff888530ad5210 FS: 0000000000000000(0000) GS:ffff888e3f800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f87223fff38 CR3: 00000007a7c6a002 CR4: 00000000007706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? die_addr+0x46/0x70 ? exc_general_protection+0x14f/0x250 ? asm_exc_general_protection+0x26/0x30 ? do_raw_read_unlock+0x44/0x70 ? btrfs_zone_finish_endio.part.0+0x34/0x160 [btrfs] btrfs_finish_one_ordered+0x5d9/0x19a0 [btrfs] ? __pfx_lock_release+0x10/0x10 ? do_raw_write_lock+0x90/0x260 ? __pfx_do_raw_write_lock+0x10/0x10 ? __pfx_btrfs_finish_one_ordered+0x10/0x10 [btrfs] ? _raw_write_unlock+0x23/0x40 ? btrfs_finish_ordered_zoned+0x5a9/0x850 [btrfs] ? lock_acquire+0x435/0x500 btrfs_work_helper+0x1b1/0xa70 [btrfs] ? __schedule+0x10a8/0x60b0 ? __pfx___might_resched+0x10/0x10 process_one_work+0x862/0x1410 ? __pfx_lock_acquire+0x10/0x10 ? __pfx_process_one_work+0x10/0x10 ? assign_work+0x16c/0x240 worker_thread+0x5e6/0x1010 ? __pfx_worker_thread+0x10/0x10 kthread+0x2c3/0x3a0 ? trace_irq_enable.constprop.0+0xce/0x110 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x31/0x70 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Enabling CONFIG_BTRFS_ASSERT revealed the following assertion to trigger: assertion failed: !list_empty(&ordered->list), in fs/btrfs/zoned.c:1815 This indicates, that we're missing the checksums list on the ordered_extent. As btrfs/167 is doing a NOCOW write this is to be expected. Further analysis with drgn confirmed the assumption: >>> inode = prog.crashed_thread().stack_trace()[11]['ordered'].inode >>> btrfs_inode = drgn.container_of(inode, "struct btrfs_inode", \ "vfs_inode") >>> print(btrfs_inode.flags) (u32)1 As zoned emulation mode simulates conventional zones on regular devices, we cannot use zone-append for writing. But we're only attaching dummy checksums if we're doing a zone-append write. So for NOCOW zoned data writes on conventional zones, also attach a dummy checksum.

In the Linux kernel, the following vulnerability has been resolved: usb: atm: cxacru: fix endpoint checking in cxacru_bind() Syzbot is still reporting quite an old issue [1] that occurs due to incomplete checking of present usb endpoints. As such, wrong endpoints types may be used at urb sumbitting stage which in turn triggers a warning in usb_submit_urb(). Fix the issue by verifying that required endpoint types are present for both in and out endpoints, taking into account cmd endpoint type. Unfortunately, this patch has not been tested on real hardware. [1] Syzbot report: usb 1-1: BOGUS urb xfer, pipe 1 != type 3 WARNING: CPU: 0 PID: 8667 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502 Modules linked in: CPU: 0 PID: 8667 Comm: kworker/0:4 Not tainted 5.14.0-rc4-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502 ... Call Trace: cxacru_cm+0x3c0/0x8e0 drivers/usb/atm/cxacru.c:649 cxacru_card_status+0x22/0xd0 drivers/usb/atm/cxacru.c:760 cxacru_bind+0x7ac/0x11a0 drivers/usb/atm/cxacru.c:1209 usbatm_usb_probe+0x321/0x1ae0 drivers/usb/atm/usbatm.c:1055 cxacru_usb_probe+0xdf/0x1e0 drivers/usb/atm/cxacru.c:1363 usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:517 [inline] really_probe+0x23c/0xcd0 drivers/base/dd.c:595 __driver_probe_device+0x338/0x4d0 drivers/base/dd.c:747 driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:777 __device_attach_driver+0x20b/0x2f0 drivers/base/dd.c:894 bus_for_each_drv+0x15f/0x1e0 drivers/base/bus.c:427 __device_attach+0x228/0x4a0 drivers/base/dd.c:965 bus_probe_device+0x1e4/0x290 drivers/base/bus.c:487 device_add+0xc2f/0x2180 drivers/base/core.c:3354 usb_set_configuration+0x113a/0x1910 drivers/usb/core/message.c:2170 usb_generic_driver_probe+0xba/0x100 drivers/usb/core/generic.c:238 usb_probe_device+0xd9/0x2c0 drivers/usb/core/driver.c:293

In the Linux kernel, the following vulnerability has been resolved: ocfs2: fix NULL pointer dereference in ocfs2_journal_dirty() bdev->bd_super has been removed and commit 8887b94d9322 change the usage from bdev->bd_super to b_assoc_map->host->i_sb. This introduces the following NULL pointer dereference in ocfs2_journal_dirty() since b_assoc_map is still not initialized. This can be easily reproduced by running xfstests generic/186, which simulate no more credits. [ 134.351592] BUG: kernel NULL pointer dereference, address: 0000000000000000 ... [ 134.355341] RIP: 0010:ocfs2_journal_dirty+0x14f/0x160 [ocfs2] ... [ 134.365071] Call Trace: [ 134.365312] <TASK> [ 134.365524] ? __die_body+0x1e/0x60 [ 134.365868] ? page_fault_oops+0x13d/0x4f0 [ 134.366265] ? __pfx_bit_wait_io+0x10/0x10 [ 134.366659] ? schedule+0x27/0xb0 [ 134.366981] ? exc_page_fault+0x6a/0x140 [ 134.367356] ? asm_exc_page_fault+0x26/0x30 [ 134.367762] ? ocfs2_journal_dirty+0x14f/0x160 [ocfs2] [ 134.368305] ? ocfs2_journal_dirty+0x13d/0x160 [ocfs2] [ 134.368837] ocfs2_create_new_meta_bhs.isra.51+0x139/0x2e0 [ocfs2] [ 134.369454] ocfs2_grow_tree+0x688/0x8a0 [ocfs2] [ 134.369927] ocfs2_split_and_insert.isra.67+0x35c/0x4a0 [ocfs2] [ 134.370521] ocfs2_split_extent+0x314/0x4d0 [ocfs2] [ 134.371019] ocfs2_change_extent_flag+0x174/0x410 [ocfs2] [ 134.371566] ocfs2_add_refcount_flag+0x3fa/0x630 [ocfs2] [ 134.372117] ocfs2_reflink_remap_extent+0x21b/0x4c0 [ocfs2] [ 134.372994] ? inode_update_timestamps+0x4a/0x120 [ 134.373692] ? __pfx_ocfs2_journal_access_di+0x10/0x10 [ocfs2] [ 134.374545] ? __pfx_ocfs2_journal_access_di+0x10/0x10 [ocfs2] [ 134.375393] ocfs2_reflink_remap_blocks+0xe4/0x4e0 [ocfs2] [ 134.376197] ocfs2_remap_file_range+0x1de/0x390 [ocfs2] [ 134.376971] ? security_file_permission+0x29/0x50 [ 134.377644] vfs_clone_file_range+0xfe/0x320 [ 134.378268] ioctl_file_clone+0x45/0xa0 [ 134.378853] do_vfs_ioctl+0x457/0x990 [ 134.379422] __x64_sys_ioctl+0x6e/0xd0 [ 134.379987] do_syscall_64+0x5d/0x170 [ 134.380550] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 134.381231] RIP: 0033:0x7fa4926397cb [ 134.381786] Code: 73 01 c3 48 8b 0d bd 56 38 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 8d 56 38 00 f7 d8 64 89 01 48 [ 134.383930] RSP: 002b:00007ffc2b39f7b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 134.384854] RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00007fa4926397cb [ 134.385734] RDX: 00007ffc2b39f7f0 RSI: 000000004020940d RDI: 0000000000000003 [ 134.386606] RBP: 0000000000000000 R08: 00111a82a4f015bb R09: 00007fa494221000 [ 134.387476] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 [ 134.388342] R13: 0000000000f10000 R14: 0000558e844e2ac8 R15: 0000000000f10000 [ 134.389207] </TASK> Fix it by only aborting transaction and journal in ocfs2_journal_dirty() now, and leave ocfs2_abort() later when detecting an aborted handle, e.g. start next transaction. Also log the handle details in this case.

In the Linux kernel, the following vulnerability has been resolved: crypto: hisilicon/sec - Fix memory leak for sec resource release The AIV is one of the SEC resources. When releasing resources, it need to release the AIV resources at the same time. Otherwise, memory leakage occurs. The aiv resource release is added to the sec resource release function.

In the Linux kernel, the following vulnerability has been resolved: mm/mglru: fix div-by-zero in vmpressure_calc_level() evict_folios() uses a second pass to reclaim folios that have gone through page writeback and become clean before it finishes the first pass, since folio_rotate_reclaimable() cannot handle those folios due to the isolation. The second pass tries to avoid potential double counting by deducting scan_control->nr_scanned. However, this can result in underflow of nr_scanned, under a condition where shrink_folio_list() does not increment nr_scanned, i.e., when folio_trylock() fails. The underflow can cause the divisor, i.e., scale=scanned+reclaimed in vmpressure_calc_level(), to become zero, resulting in the following crash: [exception RIP: vmpressure_work_fn+101] process_one_work at ffffffffa3313f2b Since scan_control->nr_scanned has no established semantics, the potential double counting has minimal risks. Therefore, fix the problem by not deducting scan_control->nr_scanned in evict_folios().

In the Linux kernel, the following vulnerability has been resolved: mm: prevent derefencing NULL ptr in pfn_section_valid() Commit 5ec8e8ea8b77 ("mm/sparsemem: fix race in accessing memory_section->usage") changed pfn_section_valid() to add a READ_ONCE() call around "ms->usage" to fix a race with section_deactivate() where ms->usage can be cleared. The READ_ONCE() call, by itself, is not enough to prevent NULL pointer dereference. We need to check its value before dereferencing it.

In the Linux kernel, the following vulnerability has been resolved: serial: imx: Introduce timeout when waiting on transmitter empty By waiting at most 1 second for USR2_TXDC to be set, we avoid a potential deadlock. In case of the timeout, there is not much we can do, so we simply ignore the transmitter state and optimistically try to continue.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix deadlock in smb2_find_smb_tcon() Unlock cifs_tcp_ses_lock before calling cifs_put_smb_ses() to avoid such deadlock.

In the Linux kernel, the following vulnerability has been resolved: ASoC: SOF: ipc4-topology: Fix input format query of process modules without base extension If a process module does not have base config extension then the same format applies to all of it's inputs and the process->base_config_ext is NULL, causing NULL dereference when specifically crafted topology and sequences used.

In the Linux kernel, the following vulnerability has been resolved: io_uring: check for non-NULL file pointer in io_file_can_poll() In earlier kernels, it was possible to trigger a NULL pointer dereference off the forced async preparation path, if no file had been assigned. The trace leading to that looks as follows: BUG: kernel NULL pointer dereference, address: 00000000000000b0 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP CPU: 67 PID: 1633 Comm: buf-ring-invali Not tainted 6.8.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS unknown 2/2/2022 RIP: 0010:io_buffer_select+0xc3/0x210 Code: 00 00 48 39 d1 0f 82 ae 00 00 00 48 81 4b 48 00 00 01 00 48 89 73 70 0f b7 50 0c 66 89 53 42 85 ed 0f 85 d2 00 00 00 48 8b 13 <48> 8b 92 b0 00 00 00 48 83 7a 40 00 0f 84 21 01 00 00 4c 8b 20 5b RSP: 0018:ffffb7bec38c7d88 EFLAGS: 00010246 RAX: ffff97af2be61000 RBX: ffff97af234f1700 RCX: 0000000000000040 RDX: 0000000000000000 RSI: ffff97aecfb04820 RDI: ffff97af234f1700 RBP: 0000000000000000 R08: 0000000000200030 R09: 0000000000000020 R10: ffffb7bec38c7dc8 R11: 000000000000c000 R12: ffffb7bec38c7db8 R13: ffff97aecfb05800 R14: ffff97aecfb05800 R15: ffff97af2be5e000 FS: 00007f852f74b740(0000) GS:ffff97b1eeec0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000000b0 CR3: 000000016deab005 CR4: 0000000000370ef0 Call Trace: <TASK> ? __die+0x1f/0x60 ? page_fault_oops+0x14d/0x420 ? do_user_addr_fault+0x61/0x6a0 ? exc_page_fault+0x6c/0x150 ? asm_exc_page_fault+0x22/0x30 ? io_buffer_select+0xc3/0x210 __io_import_iovec+0xb5/0x120 io_readv_prep_async+0x36/0x70 io_queue_sqe_fallback+0x20/0x260 io_submit_sqes+0x314/0x630 __do_sys_io_uring_enter+0x339/0xbc0 ? __do_sys_io_uring_register+0x11b/0xc50 ? vm_mmap_pgoff+0xce/0x160 do_syscall_64+0x5f/0x180 entry_SYSCALL_64_after_hwframe+0x46/0x4e RIP: 0033:0x55e0a110a67e Code: ba cc 00 00 00 45 31 c0 44 0f b6 92 d0 00 00 00 31 d2 41 b9 08 00 00 00 41 83 e2 01 41 c1 e2 04 41 09 c2 b8 aa 01 00 00 0f 05 <c3> 90 89 30 eb a9 0f 1f 40 00 48 8b 42 20 8b 00 a8 06 75 af 85 f6 because the request is marked forced ASYNC and has a bad file fd, and hence takes the forced async prep path. Current kernels with the request async prep cleaned up can no longer hit this issue, but for ease of backporting, let's add this safety check in here too as it really doesn't hurt. For both cases, this will inevitably end with a CQE posted with -EBADF.

In the Linux kernel, the following vulnerability has been resolved: drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2 [Why] Commit: - commit 5aa1dfcdf0a4 ("drm/mst: Refactor the flow for payload allocation/removement") accidently overwrite the commit - commit 54d217406afe ("drm: use mgr->dev in drm_dbg_kms in drm_dp_add_payload_part2") which cause regression. [How] Recover the original NULL fix and remove the unnecessary input parameter 'state' for drm_dp_add_payload_part2(). (cherry picked from commit 4545614c1d8da603e57b60dd66224d81b6ffc305)

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix kernel crash problem in concurrent scenario When link status change, the nic driver need to notify the roce driver to handle this event, but at this time, the roce driver may uninit, then cause kernel crash. To fix the problem, when link status change, need to check whether the roce registered, and when uninit, need to wait link update finish.

In the Linux kernel, the following vulnerability has been resolved: thermal/drivers/qcom/lmh: Check for SCM availability at probe Up until now, the necessary scm availability check has not been performed, leading to possible null pointer dereferences (which did happen for me on RB1). Fix that.

In the Linux kernel, the following vulnerability has been resolved: fpga: region: add owner module and take its refcount The current implementation of the fpga region assumes that the low-level module registers a driver for the parent device and uses its owner pointer to take the module's refcount. This approach is problematic since it can lead to a null pointer dereference while attempting to get the region during programming if the parent device does not have a driver. To address this problem, add a module owner pointer to the fpga_region struct and use it to take the module's refcount. Modify the functions for registering a region to take an additional owner module parameter and rename them to avoid conflicts. Use the old function names for helper macros that automatically set the module that registers the region as the owner. This ensures compatibility with existing low-level control modules and reduces the chances of registering a region without setting the owner. Also, update the documentation to keep it consistent with the new interface for registering an fpga region.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - Fix ADF_DEV_RESET_SYNC memory leak Using completion_done to determine whether the caller has gone away only works after a complete call. Furthermore it's still possible that the caller has not yet called wait_for_completion, resulting in another potential UAF. Fix this by making the caller use cancel_work_sync and then freeing the memory safely.

In the Linux kernel, the following vulnerability has been resolved: media: mgb4: Fix double debugfs remove Fixes an error where debugfs_remove_recursive() is called first on a parent directory and then again on a child which causes a kernel panic. [hverkuil: added Fixes/Cc tags]

In the Linux kernel, the following vulnerability has been resolved: mm/vmalloc: fix vmalloc which may return null if called with __GFP_NOFAIL commit a421ef303008 ("mm: allow !GFP_KERNEL allocations for kvmalloc") includes support for __GFP_NOFAIL, but it presents a conflict with commit dd544141b9eb ("vmalloc: back off when the current task is OOM-killed"). A possible scenario is as follows: process-a __vmalloc_node_range(GFP_KERNEL | __GFP_NOFAIL) __vmalloc_area_node() vm_area_alloc_pages() --> oom-killer send SIGKILL to process-a if (fatal_signal_pending(current)) break; --> return NULL; To fix this, do not check fatal_signal_pending() in vm_area_alloc_pages() if __GFP_NOFAIL set. This issue occurred during OPLUS KASAN TEST. Below is part of the log -> oom-killer sends signal to process [65731.222840] [ T1308] oom-kill:constraint=CONSTRAINT_NONE,nodemask=(null),cpuset=/,mems_allowed=0,global_oom,task_memcg=/apps/uid_10198,task=gs.intelligence,pid=32454,uid=10198 [65731.259685] [T32454] Call trace: [65731.259698] [T32454] dump_backtrace+0xf4/0x118 [65731.259734] [T32454] show_stack+0x18/0x24 [65731.259756] [T32454] dump_stack_lvl+0x60/0x7c [65731.259781] [T32454] dump_stack+0x18/0x38 [65731.259800] [T32454] mrdump_common_die+0x250/0x39c [mrdump] [65731.259936] [T32454] ipanic_die+0x20/0x34 [mrdump] [65731.260019] [T32454] atomic_notifier_call_chain+0xb4/0xfc [65731.260047] [T32454] notify_die+0x114/0x198 [65731.260073] [T32454] die+0xf4/0x5b4 [65731.260098] [T32454] die_kernel_fault+0x80/0x98 [65731.260124] [T32454] __do_kernel_fault+0x160/0x2a8 [65731.260146] [T32454] do_bad_area+0x68/0x148 [65731.260174] [T32454] do_mem_abort+0x151c/0x1b34 [65731.260204] [T32454] el1_abort+0x3c/0x5c [65731.260227] [T32454] el1h_64_sync_handler+0x54/0x90 [65731.260248] [T32454] el1h_64_sync+0x68/0x6c [65731.260269] [T32454] z_erofs_decompress_queue+0x7f0/0x2258 --> be->decompressed_pages = kvcalloc(be->nr_pages, sizeof(struct page *), GFP_KERNEL | __GFP_NOFAIL); kernel panic by NULL pointer dereference. erofs assume kvmalloc with __GFP_NOFAIL never return NULL. [65731.260293] [T32454] z_erofs_runqueue+0xf30/0x104c [65731.260314] [T32454] z_erofs_readahead+0x4f0/0x968 [65731.260339] [T32454] read_pages+0x170/0xadc [65731.260364] [T32454] page_cache_ra_unbounded+0x874/0xf30 [65731.260388] [T32454] page_cache_ra_order+0x24c/0x714 [65731.260411] [T32454] filemap_fault+0xbf0/0x1a74 [65731.260437] [T32454] __do_fault+0xd0/0x33c [65731.260462] [T32454] handle_mm_fault+0xf74/0x3fe0 [65731.260486] [T32454] do_mem_abort+0x54c/0x1b34 [65731.260509] [T32454] el0_da+0x44/0x94 [65731.260531] [T32454] el0t_64_sync_handler+0x98/0xb4 [65731.260553] [T32454] el0t_64_sync+0x198/0x19c

Uncontrolled resource consumption in some Intel(R) Aptio* V UEFI Firmware Integrator Tools may allow an authenticated user to potentially enable denial of service via local access.

In the Linux kernel, the following vulnerability has been resolved: fbdev: savage: Handle err return when savagefb_check_var failed The commit 04e5eac8f3ab("fbdev: savage: Error out if pixclock equals zero") checks the value of pixclock to avoid divide-by-zero error. However the function savagefb_probe doesn't handle the error return of savagefb_check_var. When pixclock is 0, it will cause divide-by-zero error.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix deadlock during RTC update There is a deadlock when runtime suspend waits for the flush of RTC work, and the RTC work calls ufshcd_rpm_get_sync() to wait for runtime resume. Here is deadlock backtrace: kworker/0:1 D 4892.876354 10 10971 4859 0x4208060 0x8 10 0 120 670730152367 ptr f0ffff80c2e40000 0 1 0x00000001 0x000000ff 0x000000ff 0x000000ff <ffffffee5e71ddb0> __switch_to+0x1a8/0x2d4 <ffffffee5e71e604> __schedule+0x684/0xa98 <ffffffee5e71ea60> schedule+0x48/0xc8 <ffffffee5e725f78> schedule_timeout+0x48/0x170 <ffffffee5e71fb74> do_wait_for_common+0x108/0x1b0 <ffffffee5e71efe0> wait_for_completion+0x44/0x60 <ffffffee5d6de968> __flush_work+0x39c/0x424 <ffffffee5d6decc0> __cancel_work_sync+0xd8/0x208 <ffffffee5d6dee2c> cancel_delayed_work_sync+0x14/0x28 <ffffffee5e2551b8> __ufshcd_wl_suspend+0x19c/0x480 <ffffffee5e255fb8> ufshcd_wl_runtime_suspend+0x3c/0x1d4 <ffffffee5dffd80c> scsi_runtime_suspend+0x78/0xc8 <ffffffee5df93580> __rpm_callback+0x94/0x3e0 <ffffffee5df90b0c> rpm_suspend+0x2d4/0x65c <ffffffee5df91448> __pm_runtime_suspend+0x80/0x114 <ffffffee5dffd95c> scsi_runtime_idle+0x38/0x6c <ffffffee5df912f4> rpm_idle+0x264/0x338 <ffffffee5df90f14> __pm_runtime_idle+0x80/0x110 <ffffffee5e24ce44> ufshcd_rtc_work+0x128/0x1e4 <ffffffee5d6e3a40> process_one_work+0x26c/0x650 <ffffffee5d6e65c8> worker_thread+0x260/0x3d8 <ffffffee5d6edec8> kthread+0x110/0x134 <ffffffee5d616b18> ret_from_fork+0x10/0x20 Skip updating RTC if RPM state is not RPM_ACTIVE.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: connac: check for null before dereferencing The wcid can be NULL. It should be checked for validity before dereferencing it to avoid crash.

In the Linux kernel, the following vulnerability has been resolved: md: fix resync softlockup when bitmap size is less than array size Is is reported that for dm-raid10, lvextend + lvchange --syncaction will trigger following softlockup: kernel:watchdog: BUG: soft lockup - CPU#3 stuck for 26s! [mdX_resync:6976] CPU: 7 PID: 3588 Comm: mdX_resync Kdump: loaded Not tainted 6.9.0-rc4-next-20240419 #1 RIP: 0010:_raw_spin_unlock_irq+0x13/0x30 Call Trace: <TASK> md_bitmap_start_sync+0x6b/0xf0 raid10_sync_request+0x25c/0x1b40 [raid10] md_do_sync+0x64b/0x1020 md_thread+0xa7/0x170 kthread+0xcf/0x100 ret_from_fork+0x30/0x50 ret_from_fork_asm+0x1a/0x30 And the detailed process is as follows: md_do_sync j = mddev->resync_min while (j < max_sectors) sectors = raid10_sync_request(mddev, j, &skipped) if (!md_bitmap_start_sync(..., &sync_blocks)) // md_bitmap_start_sync set sync_blocks to 0 return sync_blocks + sectors_skippe; // sectors = 0; j += sectors; // j never change Root cause is that commit 301867b1c168 ("md/raid10: check slab-out-of-bounds in md_bitmap_get_counter") return early from md_bitmap_get_counter(), without setting returned blocks. Fix this problem by always set returned blocks from md_bitmap_get_counter"(), as it used to be. Noted that this patch just fix the softlockup problem in kernel, the case that bitmap size doesn't match array size still need to be fixed.

In the Linux kernel, the following vulnerability has been resolved: net: micrel: Fix receiving the timestamp in the frame for lan8841 The blamed commit started to use the ptp workqueue to get the second part of the timestamp. And when the port was set down, then this workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING is not enabled, then the ptp_clock is not initialized so then it would crash when it would try to access the delayed work. So then basically by setting up and then down the port, it would crash. The fix consists in checking if the ptp_clock is initialized and only then cancel the delayed work.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix netif state handling mlx5e_suspend cleans resources only if netif_device_present() returns true. However, mlx5e_resume changes the state of netif, via mlx5e_nic_enable, only if reg_state == NETREG_REGISTERED. In the below case, the above leads to NULL-ptr Oops[1] and memory leaks: mlx5e_probe _mlx5e_resume mlx5e_attach_netdev mlx5e_nic_enable <-- netdev not reg, not calling netif_device_attach() register_netdev <-- failed for some reason. ERROR_FLOW: _mlx5e_suspend <-- netif_device_present return false, resources aren't freed :( Hence, clean resources in this case as well. [1] BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 0 P4D 0 Oops: 0010 [#1] SMP CPU: 2 PID: 9345 Comm: test-ovs-ct-gen Not tainted 6.5.0_for_upstream_min_debug_2023_09_05_16_01 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:0x0 Code: Unable to access opcode bytes at0xffffffffffffffd6. RSP: 0018:ffff888178aaf758 EFLAGS: 00010246 Call Trace: <TASK> ? __die+0x20/0x60 ? page_fault_oops+0x14c/0x3c0 ? exc_page_fault+0x75/0x140 ? asm_exc_page_fault+0x22/0x30 notifier_call_chain+0x35/0xb0 blocking_notifier_call_chain+0x3d/0x60 mlx5_blocking_notifier_call_chain+0x22/0x30 [mlx5_core] mlx5_core_uplink_netdev_event_replay+0x3e/0x60 [mlx5_core] mlx5_mdev_netdev_track+0x53/0x60 [mlx5_ib] mlx5_ib_roce_init+0xc3/0x340 [mlx5_ib] __mlx5_ib_add+0x34/0xd0 [mlx5_ib] mlx5r_probe+0xe1/0x210 [mlx5_ib] ? auxiliary_match_id+0x6a/0x90 auxiliary_bus_probe+0x38/0x80 ? driver_sysfs_add+0x51/0x80 really_probe+0xc9/0x3e0 ? driver_probe_device+0x90/0x90 __driver_probe_device+0x80/0x160 driver_probe_device+0x1e/0x90 __device_attach_driver+0x7d/0x100 bus_for_each_drv+0x80/0xd0 __device_attach+0xbc/0x1f0 bus_probe_device+0x86/0xa0 device_add+0x637/0x840 __auxiliary_device_add+0x3b/0xa0 add_adev+0xc9/0x140 [mlx5_core] mlx5_rescan_drivers_locked+0x22a/0x310 [mlx5_core] mlx5_register_device+0x53/0xa0 [mlx5_core] mlx5_init_one_devl_locked+0x5c4/0x9c0 [mlx5_core] mlx5_init_one+0x3b/0x60 [mlx5_core] probe_one+0x44c/0x730 [mlx5_core] local_pci_probe+0x3e/0x90 pci_device_probe+0xbf/0x210 ? kernfs_create_link+0x5d/0xa0 ? sysfs_do_create_link_sd+0x60/0xc0 really_probe+0xc9/0x3e0 ? driver_probe_device+0x90/0x90 __driver_probe_device+0x80/0x160 driver_probe_device+0x1e/0x90 __device_attach_driver+0x7d/0x100 bus_for_each_drv+0x80/0xd0 __device_attach+0xbc/0x1f0 pci_bus_add_device+0x54/0x80 pci_iov_add_virtfn+0x2e6/0x320 sriov_enable+0x208/0x420 mlx5_core_sriov_configure+0x9e/0x200 [mlx5_core] sriov_numvfs_store+0xae/0x1a0 kernfs_fop_write_iter+0x10c/0x1a0 vfs_write+0x291/0x3c0 ksys_write+0x5f/0xe0 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 CR2: 0000000000000000 ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: dma-buf/sw-sync: don't enable IRQ from sync_print_obj() Since commit a6aa8fca4d79 ("dma-buf/sw-sync: Reduce irqsave/irqrestore from known context") by error replaced spin_unlock_irqrestore() with spin_unlock_irq() for both sync_debugfs_show() and sync_print_obj() despite sync_print_obj() is called from sync_debugfs_show(), lockdep complains inconsistent lock state warning. Use plain spin_{lock,unlock}() for sync_print_obj(), for sync_debugfs_show() is already using spin_{lock,unlock}_irq().

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Modify the print level of CQE error Too much print may lead to a panic in kernel. Change ibdev_err() to ibdev_err_ratelimited(), and change the printing level of cqe dump to debug level.

In the Linux kernel, the following vulnerability has been resolved: serial: max3100: Update uart_driver_registered on driver removal The removal of the last MAX3100 device triggers the removal of the driver. However, code doesn't update the respective global variable and after insmod — rmmod — insmod cycle the kernel oopses: max3100 spi-PRP0001:01: max3100_probe: adding port 0 BUG: kernel NULL pointer dereference, address: 0000000000000408 ... RIP: 0010:serial_core_register_port+0xa0/0x840 ... max3100_probe+0x1b6/0x280 [max3100] spi_probe+0x8d/0xb0 Update the actual state so next time UART driver will be registered again. Hugo also noticed, that the error path in the probe also affected by having the variable set, and not cleared. Instead of clearing it move the assignment after the successfull uart_register_driver() call.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Check 'folio' pointer for NULL It can be NULL if bmap is called.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: configfs: Prevent OOB read/write in usb_string_copy() Userspace provided string 's' could trivially have the length zero. Left unchecked this will firstly result in an OOB read in the form `if (str[0 - 1] == '\n') followed closely by an OOB write in the form `str[0 - 1] = '\0'`. There is already a validating check to catch strings that are too long. Let's supply an additional check for invalid strings that are too short.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add null check for set_output_gamma in dcn30_set_output_transfer_func This commit adds a null check for the set_output_gamma function pointer in the dcn30_set_output_transfer_func function. Previously, set_output_gamma was being checked for nullity at line 386, but then it was being dereferenced without any nullity check at line 401. This could potentially lead to a null pointer dereference error if set_output_gamma is indeed null. To fix this, we now ensure that set_output_gamma is not null before dereferencing it. We do this by adding a nullity check for set_output_gamma before the call to set_output_gamma at line 401. If set_output_gamma is null, we log an error message and do not call the function. This fix prevents a potential null pointer dereference error. drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn30/dcn30_hwseq.c:401 dcn30_set_output_transfer_func() error: we previously assumed 'mpc->funcs->set_output_gamma' could be null (see line 386) drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn30/dcn30_hwseq.c 373 bool dcn30_set_output_transfer_func(struct dc *dc, 374 struct pipe_ctx *pipe_ctx, 375 const struct dc_stream_state *stream) 376 { 377 int mpcc_id = pipe_ctx->plane_res.hubp->inst; 378 struct mpc *mpc = pipe_ctx->stream_res.opp->ctx->dc->res_pool->mpc; 379 const struct pwl_params *params = NULL; 380 bool ret = false; 381 382 /* program OGAM or 3DLUT only for the top pipe*/ 383 if (pipe_ctx->top_pipe == NULL) { 384 /*program rmu shaper and 3dlut in MPC*/ 385 ret = dcn30_set_mpc_shaper_3dlut(pipe_ctx, stream); 386 if (ret == false && mpc->funcs->set_output_gamma) { ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ If this is NULL 387 if (stream->out_transfer_func.type == TF_TYPE_HWPWL) 388 params = &stream->out_transfer_func.pwl; 389 else if (pipe_ctx->stream->out_transfer_func.type == 390 TF_TYPE_DISTRIBUTED_POINTS && 391 cm3_helper_translate_curve_to_hw_format( 392 &stream->out_transfer_func, 393 &mpc->blender_params, false)) 394 params = &mpc->blender_params; 395 /* there are no ROM LUTs in OUTGAM */ 396 if (stream->out_transfer_func.type == TF_TYPE_PREDEFINED) 397 BREAK_TO_DEBUGGER(); 398 } 399 } 400 --> 401 mpc->funcs->set_output_gamma(mpc, mpcc_id, params); ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ Then it will crash 402 return ret; 403 }

In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: Assign dummy when codec not specified for a DAI link MediaTek sound card drivers are checking whether a DAI link is present and used on a board to assign the correct parameters and this is done by checking the codec DAI names at probe time. If no real codec is present, assign the dummy codec to the DAI link to avoid NULL pointer during string comparison.

In the Linux kernel, the following vulnerability has been resolved: ALSA: Fix deadlocks with kctl removals at disconnection In snd_card_disconnect(), we set card->shutdown flag at the beginning, call callbacks and do sync for card->power_ref_sleep waiters at the end. The callback may delete a kctl element, and this can lead to a deadlock when the device was in the suspended state. Namely: * A process waits for the power up at snd_power_ref_and_wait() in snd_ctl_info() or read/write() inside card->controls_rwsem. * The system gets disconnected meanwhile, and the driver tries to delete a kctl via snd_ctl_remove*(); it tries to take card->controls_rwsem again, but this is already locked by the above. Since the sleeper isn't woken up, this deadlocks. An easy fix is to wake up sleepers before processing the driver disconnect callbacks but right after setting the card->shutdown flag. Then all sleepers will abort immediately, and the code flows again. So, basically this patch moves the wait_event() call at the right timing. While we're at it, just to be sure, call wait_event_all() instead of wait_event(), although we don't use exclusive events on this queue for now.

In the Linux kernel, the following vulnerability has been resolved: drivers/perf: hisi: hns3: Actually use devm_add_action_or_reset() pci_alloc_irq_vectors() allocates an irq vector. When devm_add_action() fails, the irq vector is not freed, which leads to a memory leak. Replace the devm_add_action with devm_add_action_or_reset to ensure the irq vector can be destroyed when it fails.