An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX Series and NFX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS). If an affected device receives specific valid traffic destined to the device, it will cause the PFE to crash and restart. Continued receipt and processing of this traffic will create a sustained DoS condition. This issue affects Junos OS on SRX Series: * 21.4 versions before 21.4R3-S7.9, * 22.1 versions before 22.1R3-S5.3, * 22.2 versions before 22.2R3-S4.11, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R3. This issue affects Junos OS on NFX Series: * 21.4 versions before 21.4R3-S8, * 22.1 versions after 22.1R1, * 22.2 versions before 22.2R3-S5, * 22.3 versions before 22.3R3, * 22.4 versions before 22.4R3. Junos OS versions prior to 21.4R1 are not affected by this issue.

A Missing Release of Memory after Effective Lifetime vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). In a Juniper Flow Monitoring (jflow) scenario route churn that causes BGP next hops to be updated will cause a slow memory leak and eventually a crash and restart of rpd. Thread level memory utilization for the areas where the leak occurs can be checked using the below command: user@host> show task memory detail | match so_in so_in6 28 32 344450 11022400 344760 11032320 so_in 8 16 1841629 29466064 1841734 29467744 This issue affects: Junos OS * 21.4 versions earlier than 21.4R3; * 22.1 versions earlier than 22.1R3; * 22.2 versions earlier than 22.2R3. Junos OS Evolved * 21.4-EVO versions earlier than 21.4R3-EVO; * 22.1-EVO versions earlier than 22.1R3-EVO; * 22.2-EVO versions earlier than 22.2R3-EVO. This issue does not affect: Juniper Networks Junos OS versions earlier than 21.4R1. Juniper Networks Junos OS Evolved versions earlier than 21.4R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series allows a unauthenticated network-based attacker to cause an infinite loop, resulting in a Denial of Service (DoS). An attacker who sends malformed TCP traffic via an interface configured with PPPoE, causes an infinite loop on the respective PFE. This results in consuming all resources and a manual restart is needed to recover. This issue affects interfaces with PPPoE configured and tcp-mss enabled. This issue affects Juniper Networks Junos OS * All versions prior to 20.4R3-S7; * 21.1 version 21.1R1 and later versions; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S3; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3; * 22.3 versions prior to 22.3R2-S2; * 22.4 versions prior to 22.4R2;

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX10000 Series allows a network based attacker to cause a Denial of Service (DoS). If a specific valid IP packet is received and that packet needs to be routed over a VXLAN tunnel, this will result in a PFE wedge condition due to which traffic gets impacted. As this is not a crash and restart scenario, this condition will persist until the system is rebooted to recover. This issue affects Juniper Networks Junos OS on QFX10000: 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S5; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2; 22.3 versions prior to 22.3R1-S2, 22.3R2.

An Improper Validation of Array Index vulnerability in the Advanced Forwarding Toolkit Manager daemon (aftmand) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On the PTX10008 and PTX10016 platforms running Junos OS or Junos OS Evolved, when a specific SNMP MIB is queried this will cause a PFE crash and the FPC will go offline and not automatically recover. A system restart is required to get the affected FPC in an operational state again. This issue affects: Juniper Networks Junos OS 22.1 version 22.1R2 and later versions; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. Juniper Networks Junos OS Evolved 21.3-EVO version 21.3R3-EVO and later versions; 21.4-EVO version 21.4R1-S2-EVO, 21.4R2-EVO and later versions prior to 21.4R2-S1-EVO; 22.1-EVO version 22.1R2-EVO and later versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R1-S1-EVO, 22.2R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If specific traffic is received on MX Series and its rate exceeds the respective DDoS protection limit the ingress PFE will crash and restart. Continued receipt of this traffic will create a sustained DoS condition. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S5; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.

A Denial of Service (DoS) vulnerability in BGP in Juniper Networks Junos OS configured as a VPLS PE allows an attacker to craft a specific BGP message to cause the routing protocol daemon (rpd) process to crash and restart. While rpd restarts after a crash, repeated crashes can result in an extended DoS condition. This issue only affects PE routers configured with BGP Auto discovery for LDP VPLS. Other BGP configurations are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D81; 12.3 versions prior to 12.3R12-S12; 12.3X48 versions prior to 12.3X48-D76; 14.1X53 versions prior to 14.1X53-D48; 15.1 versions prior to 15.1F6-S12, 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D150; 15.1X53 versions prior to 15.1X53-D235, 15.1X53-D495, 15.1X53-D590, 15.1X53-D68; 16.1 versions prior to 16.1R3-S10, 16.1R4-S12, 16.1R6-S6, 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R1-S5, 17.4R2; 18.1 versions prior to 18.1R2-S3, 18.1R3.

An Improper Check or Handling of Exceptional Conditions within the storm control feature of Juniper Networks Junos OS allows an attacker sending a high rate of traffic to cause a Denial of Service. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Storm control monitors the level of applicable incoming traffic and compares it with the level specified. If the combined level of the applicable traffic exceeds the specified level, the switch drops packets for the controlled traffic types. This issue affects Juniper Networks Junos OS on QFX10002: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

The SRX flowd process, responsible for packet forwarding, may crash and restart when processing specific multicast packets. By continuously sending the specific multicast packets, an attacker can repeatedly crash the flowd process causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D180; 17.3 versions; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S6; 18.2 versions prior to 18.2R2-S4, 18.2R3; 18.3 versions prior to 18.3R2-S1, 18.3R3; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R1-S1, 19.1R2.

Receipt of a specific packet on the out-of-band management interface fxp0 may cause the system to crash and restart (vmcore). By continuously sending a specially crafted packet to the fxp0 interface, an attacker can repetitively crash the rpd process causing prolonged Denial of Service (DoS). Affected releases are Juniper Networks SRX5000 Series: 12.1X46 versions prior to 12.1X46-D82; 12.3X48 versions prior to 12.3X48-D80; 15.1X49 versions prior to 15.1X49-D160.

SSL-Proxy feature on SRX devices fails to handle a hardware resource limitation which can be exploited by remote SSL/TLS servers to crash the flowd daemon. Repeated crashes of the flowd daemon can result in an extended denial of service condition. For this issue to occur, clients protected by the SRX device must initiate a connection to the malicious server. This issue affects: Juniper Networks Junos OS on SRX5000 Series: 12.3X48 versions prior to 12.3X48-D85; 15.1X49 versions prior to 15.1X49-D180; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S6, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2; 19.1 versions prior to 19.1R2.

Receipt of a malformed packet on MX Series devices with dynamic vlan configuration can trigger an uncontrolled recursion loop in the Broadband Edge subscriber management daemon (bbe-smgd), and lead to high CPU usage and a crash of the bbe-smgd service. Repeated receipt of the same packet can result in an extended denial of service condition for the device. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S1; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.

In a Dynamic Host Configuration Protocol version 6 (DHCPv6) environment, the jdhcpd daemon may crash and restart upon receipt of certain DHCPv6 solicit messages received from a DHCPv6 client. By continuously sending the same crafted packet, an attacker can repeatedly crash the jdhcpd process causing a sustained Denial of Service (DoS) to both IPv4 and IPv6 clients. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1F6-S12, 15.1R7-S3; 15.1X49 versions prior to 15.1X49-D171, 15.1X49-D180; 15.1X53 versions prior to 15.1X53-D236, 15.1X53-D496; 16.1 versions prior to 16.1R3-S10, 16.1R7-S4; 16.2 versions prior to 16.2R2-S8; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R1-S8, 17.2R3-S1; 17.3 versions prior to 17.3R3-S3; 17.4 versions prior to 17.4R1-S6, 17.4R2-S3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S2; 18.2 versions prior to 18.2R2; 18.2X75 versions prior to 18.2X75-D30; 18.3 versions prior to 18.3R1-S2. This issue does not affect Junos OS releases prior to 15.1.

On SRX5000 Series devices, if 'set security zones security-zone <zone> tcp-rst' is configured, the flowd process may crash when a specific TCP packet is received by the device and triggers a new session. The process restarts automatically. However, receipt of a constant stream of these TCP packets may result in an extended Denial of Service (DoS) condition on the device. This issue affects Juniper Networks Junos OS: 18.2R3 on SRX 5000 Series; 18.4R2 on SRX 5000 Series; 19.2R1 on SRX 5000 Series.

An unexpected status return value weakness in the Next-Generation Multicast VPN (NG-mVPN) service of Juniper Networks Junos OS allows attacker to cause a Denial of Service (DoS) condition and core the routing protocol daemon (rpd) process when a specific malformed IPv4 packet is received by the device running BGP. This malformed packet can be crafted and sent to a victim device including when forwarded directly through a device receiving such a malformed packet, but not if the malformed packet is first de-encapsulated from an encapsulated format by a receiving device. Continued receipt of the malformed packet will result in a sustained Denial of Service condition. This issue affects: Juniper Networks Junos OS 15.1 versions prior to 15.1F6-S12, 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D68, 15.1X53-D235, 15.1X53-D495, 15.1X53-D590; 16.1 versions prior to 16.1R3-S10, 16.1R4-S12, 16.1R6-S6, 16.1R7-S2; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3.

Specific IPv6 DHCP packets received by the jdhcpd daemon will cause a memory resource consumption issue to occur on a Junos OS device using the jdhcpd daemon configured to respond to IPv6 requests. Once started, memory consumption will eventually impact any IPv4 or IPv6 request serviced by the jdhcpd daemon, thus creating a Denial of Service (DoS) condition to clients requesting and not receiving IP addresses. Additionally, some clients which were previously holding IPv6 addresses will not have their IPv6 Identity Association (IA) address and network tables agreed upon by the jdhcpd daemon after the failover event occurs, which leads to more than one interface, and multiple IP addresses, being denied on the client. Affected releases are Juniper Networks Junos OS: 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R2.

An Improper Validation of Syntactic Correctness of Input vulnerability in Intrusion Detection and Prevention (IDP) of Juniper Networks SRX Series and MX Series allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). Continued receipt of this specific packet will cause a sustained Denial of Service condition. On all SRX Series and MX Series platforms, where IDP is enabled and a specific malformed SSL packet is received, the SSL detector crashes leading to an FPC core. This issue affects Juniper Networks SRX Series and MX Series prior to SigPack 3598. In order to identify the current SigPack version, following command can be used: user@junos# show security idp security-package-version

A Use of Uninitialized Resource vulnerability in the Border Gateway Protocol (BGP) software of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to send specific genuine BGP packets to a device configured with BGP to cause a Denial of Service (DoS) by crashing the Routing Protocol Daemon (rpd). This issue is triggered when the packets attempt to initiate a BGP connection before a BGP session is successfully established. Continued receipt of these specific BGP packets will cause a sustained Denial of Service condition. This issue is triggerable in both iBGP and eBGP deployments. This issue affects: Juniper Networks Junos OS 21.1 version 21.1R1 and later versions prior to 21.1R3-S5; 21.2 version 21.2R1 and later versions prior to 21.2R3-S2; 21.3 version 21.3R1 and later versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1. This issue affects: Juniper Networks Junos OS Evolved 21.1-EVO version 21.1R1-EVO and later versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.1R1-EVO.

An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network based, unauthenticated attacker to cause an RPD crash leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Upon receipt of a malformed BGP flowspec update, RPD will crash resulting in a Denial of Service. This issue affects Juniper Networks Junos OS: All versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2; Juniper Networks Junos OS Evolved: All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R2-EVO; 20.3 versions prior to 20.3R2-EVO;

A Missing Release of Memory after Effective Lifetime vulnerability in the routing protocol daemon of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network based attacker to cause a Denial of Service (DoS). In a BGP rib sharding scenario, when an attribute of an active BGP route is updated memory will leak. As rpd memory usage increases over time the rpd process will eventually run out of memory, crash, and restart. The memory utilization can be monitored with the following CLI commands: show task memory show system processes extensive | match rpd This issue affects: Juniper Networks Junos OS 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2. Juniper Networks Junos OS Evolved 20.3-EVO version 20.3R1-EVO and later versions; 20.4-EVO versions prior to 20.4R3-S6-EVO; 21.2-EVO versions prior to 21.2R3-EVO; 21.3-EVO versions prior to 21.3R2-EVO.

When an MX Series Broadband Remote Access Server (BRAS) is configured as a Broadband Network Gateway (BNG) with DHCPv6 enabled, jdhcpd might crash when receiving a specific crafted DHCP response message on a subscriber interface. The daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue only affects systems configured with DHCPv6 enabled. DHCPv4 is unaffected by this issue. This issue affects Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S5 on MX Series; 16.1 versions prior to 16.1R7-S5 on MX Series; 16.2 versions prior to 16.2R2-S10 on MX Series; 17.1 versions prior to 17.1R3-S1 on MX Series; 17.2 versions prior to 17.2R3-S2 on MX Series; 17.3 versions prior to 17.3R3-S6 on MX Series; 17.4 versions prior to 17.4R2-S5, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S6 on MX Series; 18.2 versions prior to 18.2R2-S4, 18.2R3 on MX Series; 18.2X75 versions prior to 18.2X75-D50 on MX Series; 18.3 versions prior to 18.3R1-S5, 18.3R3 on MX Series; 18.4 versions prior to 18.4R2 on MX Series; 19.1 versions prior to 19.1R1-S2, 19.1R2 on MX Series.

The srxpfe process may crash on SRX Series services gateways when the UTM module processes a specific fragmented HTTP packet. The packet is misinterpreted as a regular TCP packet which causes the processor to crash. This issue affects all SRX Series platforms that support URL-Filtering and have web-filtering enabled. Affected releases are Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 17.3 versions on SRX Series; 17.4 versions prior to 17.4R1-S8, 17.4R2-S5, 17.4R3 on SRX Series; 18.1 versions prior to 18.1R3-S6 on SRX Series; 18.2 versions prior to 18.2R2-S1, 18.2R3 on SRX Series; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX Series; 18.4 versions prior to 18.4R1-S1, 18.4R2 on SRX Series.

In MPLS environments, receipt of a specific SNMP packet may cause the routing protocol daemon (RPD) process to crash and restart. By continuously sending a specially crafted SNMP packet, an attacker can repetitively crash the RPD process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS : 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D48 on EX/QFX series; 15.1 versions prior to 15.1R4-S9, 15.1R7-S2; 15.1F6 versions prior to 15.1F6-S11; 15.1X49 versions prior to 15.1X49-D141, 15.1X49-D144, 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400 Series; 15.1X54 on ACX Series; 16.1 versions prior to 16.1R3-S10, 16.1R4-S11, 16.1R6-S5, 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S8, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R1-S1, 18.1R2-S1, 18.1R3; 18.2X75 versions prior to 18.2X75-D10.

The flowd process, responsible for forwarding traffic in SRX Series services gateways, may crash and restart when processing specific transit IP packets through an IPSec tunnel. Continued processing of these packets may result in an extended Denial of Service (DoS) condition. This issue only occurs when IPSec tunnels are configured. Systems without IPSec tunnel configurations are not vulnerable to this issue. This issue affects Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D171, 15.1X49-D180 on SRX Series; 18.2 versions 18.2R2-S1 and later, prior to 18.2R3 on SRX Series; 18.4 versions prior to 18.4R2 on SRX Series.

A vulnerability in the SIP ALG packet processing service of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending specific types of valid SIP traffic to the device. In this case, the flowd process crashes and generates a core dump while processing SIP ALG traffic. Continued receipt of these valid SIP packets will result in a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D61, 12.3X48-D65 on SRX Series; 15.1X49 versions prior to 15.1X49-D130 on SRX Series; 17.3 versions prior to 17.3R3 on SRX Series; 17.4 versions prior to 17.4R2 on SRX Series.

When BGP tracing is enabled an incoming BGP message may cause the Junos OS routing protocol daemon (rpd) process to crash and restart. While rpd restarts after a crash, repeated crashes can result in an extended DoS condition. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S4, 16.1R7-S5; 16.2 versions prior to 16.2R2-S9, 16.2R3; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3-S1; 17.3 versions prior to 17.3R3-S3, 17.3R3-S4, 17.3R4; 17.4 versions prior to 17.4R1-S7, 17.4R2-S3, 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S4, 18.1R4; 18.2 versions prior to 18.2R2-S2, 18.2R2-S3, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S3, 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. This issue does not affect Junos releases prior to 16.1R1.

A memory leak vulnerability in the of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the device by sending specific commands from a peered BGP host and having those BGP states delivered to the vulnerable device. This issue affects: Juniper Networks Junos OS: 18.1 versions prior to 18.1R2-S4, 18.1R3-S1; 18.1X75 all versions. Versions before 18.1R1 are not affected.

A vulnerability in the srxpfe process on Protocol Independent Multicast (PIM) enabled SRX series devices may lead to crash of the srxpfe process and an FPC reboot while processing (PIM) messages. Sustained receipt of these packets may lead to an extended denial of service condition. Affected releases are Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D80; 15.1X49 versions prior to 15.1X49-D160; 17.3 versions prior to 17.3R3-S7 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S8; 18.2 versions prior to 18.2R2; 18.3 versions prior to 18.3R2.

On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. By simulating a specific BGP session restart, an attacker can repeatedly crash the RPD process causing prolonged denial of service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S8; 17.1 versions prior to 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R2. Junos OS releases prior to 16.1R1 are not affected.

This issue only affects devices with three (3) or more MPC10's installed in a single chassis with OSPF enabled and configured on the device. An Insufficient Resource Pool weakness allows an attacker to cause the device's Open Shortest Path First (OSPF) states to transition to Down, resulting in a Denial of Service (DoS) attack. This attack requires a relatively large number of specific Internet Mixed (IMIXed) types of genuine and valid IPv6 packets to be transferred by the attacker in a relatively short period of time, across three or more PFE's on the device at the same time. Continued receipt of the traffic sent by the attacker will continue to cause OSPF to remain in the Down starting state, or flap between other states and then again to Down, causing a persistent Denial of Service. This attack will affect all IPv4, and IPv6 traffic served by the OSPF routes once the OSPF states transition to Down. This issue affects: Juniper Networks Junos OS on MX480, MX960, MX2008, MX2010, MX2020: 18.1 versions prior to 18.1R2-S4, 18.1R3-S5; 18.1X75 version 18.1X75-D10 and later versions; 18.2 versions prior to 18.2R1-S5, 18.2R2-S3, 18.2R3; 18.2X75 versions prior to 18.2X75-D50; 18.3 versions prior to 18.3R1-S4, 18.3R2, 18.3R3; 18.4 versions prior to 18.4R1-S2, 18.4R2.

Under certain heavy traffic conditions srxpfe process can crash and result in a denial of service condition for the SRX1500 device. Repeated crashes of the srxpfe can result in an extended denial of service condition. The SRX device may fail to forward traffic when this condition occurs. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D170 on SRX1500; 17.3 versions prior to 17.3R3-S7 on SRX1500; 17.4 versions prior to 17.4R2-S8, 17.4R3 on SRX1500; 18.1 versions prior to 18.1R3-S8 on SRX1500; 18.2 versions prior to 18.2R3 on SRX1500; 18.3 versions prior to 18.3R2 on SRX1500; 18.4 versions prior to 18.4R2 on SRX1500.

On MX Series, when the SIP ALG is enabled, receipt of a certain malformed SIP packet may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending a crafted SIP packet, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on MX Series: 16.1 versions prior to 16.1R7-S5; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R3-S6 ; 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S3; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2.

An Uncontrolled Resource Consumption vulnerability in TCP processing on the Routing Engine (RE) of Juniper Networks Junos OS allows an unauthenticated network-based attacker to send crafted TCP packets destined to the device, resulting in an MBUF leak that ultimately leads to a Denial of Service (DoS). The system does not recover automatically and must be manually restarted to restore service. This issue occurs when crafted TCP packets are sent directly to a configured IPv4 or IPv6 interface on the device. Transit traffic will not trigger this issue. MBUF usage can be monitored through the use of the 'show system buffers' command. For example: user@junos> show system buffers | refresh 5 4054/566/4620 mbufs in use (current/cache/total) ... 4089/531/4620 mbufs in use (current/cache/total) ... 4151/589/4740 mbufs in use (current/cache/total) ... 4213/527/4740 mbufs in use (current/cache/total) This issue affects Juniper Networks Junos OS: 12.3 version 12.3R12-S19 and later versions; 15.1 version 15.1R7-S10 and later versions; 17.3 version 17.3R3-S12 and later versions; 18.4 version 18.4R3-S9 and later versions; 19.1 version 19.1R3-S7 and later versions; 19.2 version 19.2R3-S3 and later versions; 19.3 version 19.3R2-S7, 19.3R3-S3 and later versions prior to 19.3R3-S7; 19.4 version 19.4R2-S7, 19.4R3-S5 and later versions prior to 19.4R3-S10; 20.1 version 20.1R3-S1 and later versions; 20.2 version 20.2R3-S2 and later versions prior to 20.2R3-S6; 20.3 version 20.3R3-S1 and later versions prior to 20.3R3-S6; 20.4 version 20.4R2-S2, 20.4R3 and later versions prior to 20.4R3-S5; 21.1 version 21.1R2 and later versions prior to 21.1R3-S4; 21.2 version 21.2R1-S1, 21.2R2 and later versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2; 22.3 versions prior to 22.3R1-S1, 22.3R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the Juniper Networks Junos OS on MX Series platforms with MPC10/MPC11 line cards, allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). Devices are only vulnerable when the Suspicious Control Flow Detection (scfd) feature is enabled. Upon enabling this specific feature, an attacker sending specific traffic is causing memory to be allocated dynamically and it is not freed. Memory is not freed even after deactivating this feature. Sustained processing of such traffic will eventually lead to an out of memory condition that prevents all services from continuing to function, and requires a manual restart to recover. The FPC memory usage can be monitored using the CLI command "show chassis fpc". On running the above command, the memory of AftDdosScfdFlow can be observed to detect the memory leak. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 20.2R3-S5; 20.3 version 20.3R1 and later versions.

A Missing Release of Memory after Effective Lifetime vulnerability in the Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In an IPsec VPN environment, a memory leak will be seen if a DH or ECDH group is configured. Eventually the flowd process will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

A Buffer Overflow vulnerability in SIP ALG of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On all MX Series and SRX Series platform with SIP ALG enabled, when a malformed SIP packet is received, the flow processing daemon (flowd) will crash and restart. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on SRX Series.

An Improper Validation of Array Index vulnerability in the SIP ALG of Juniper Networks Junos OS on SRX 5000 Series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an attacker sends an SIP packets with a malformed SDP field then the SIP ALG can not process it which will lead to an FPC crash and restart. Continued receipt of these specific packets will lead to a sustained Denial of Service. This issue can only occur when both below mentioned conditions are fulfilled: 1. Call distribution needs to be enabled: [security alg sip enable-call-distribution] 2. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX, and MX with SPC3 use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX 5000 Series: 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R1-S1, 22.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

An Uncontrolled Resource Consumption vulnerability in the PFE management daemon (evo-pfemand) of Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause an FPC crash leading to a Denial of Service (DoS). When a specific SNMP GET operation or a specific CLI command is executed this will cause a GUID resource leak, eventually leading to exhaustion and result in an FPC crash and reboot. GUID exhaustion will trigger a syslog message like one of the following for example: evo-pfemand[<pid>]: get_next_guid: Ran out of Guid Space ... evo-aftmand-zx[<pid>]: get_next_guid: Ran out of Guid Space ... This leak can be monitored by running the following command and taking note of the value in the rightmost column labeled Guids: user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3448 0 3448 re0 evo-pfemand net::juniper::interfaces::IFLId 0 561 0 561 user@host> show platform application-info allocations app evo-pfemand | match "IFDId|IFLId|Context" Node Application Context Name Live Allocs Fails Guids re0 evo-pfemand net::juniper::interfaces::IFDId 0 3784 0 3784 re0 evo-pfemand net::juniper::interfaces::IFLId 0 647 0 647 This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S3-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO versions prior to 21.2R3-S4-EVO; 21.3-EVO version 21.3R1-EVO and later versions; 21.4-EVO versions prior to 21.4R2-EVO.

An Improper Check or Handling of Exceptional Conditions vulnerability in the IPsec library of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause Denial of Service (DoS). On all MX platforms with MS-MPC or MS-MIC card, when specific IPv4 packets are processed by an IPsec6 tunnel, the Multiservices PIC Management Daemon (mspmand) process will core and restart. This will lead to FPC crash. Traffic flow is impacted while mspmand restarts. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue only occurs if an IPv4 address is not configured on the multiservice interface. This issue affects: Juniper Networks Junos OS on MX Series All versions prior to 19.4R3-S9; 20.1 version 20.1R3-S5 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2.

A vulnerability in class-of-service (CoS) queue management in Juniper Networks Junos OS on the ACX2K Series devices allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). Specific packets are being incorrectly routed to a queue used for other high-priority traffic such as BGP, PIM, ICMP, ICMPV6 ND and ISAKMP. Due to this misclassification of traffic, receipt of a high rate of these specific packets will cause delays in the processing of other traffic, leading to a Denial of Service (DoS). Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX2K Series: All versions prior to 19.4R3-S9; All 20.2 versions; 20.3 versions prior to 20.3R3-S6 on ACX2K Series; 20.4 versions prior to 20.4R3-S4 on ACX2K Series; All 21.1 versions; 21.2 versions prior to 21.2R3-S3 on ACX2K Series. Note: This issues affects legacy ACX2K Series PPC-based devices. This platform reached Last Supported Version (LSV) as of the Junos OS 21.2 Release.

An Improper Locking vulnerability in the SIP ALG of Juniper Networks Junos OS on MX Series with MS-MPC or MS-MIC card and SRX Series allows an unauthenticated, network-based attacker to cause a flow processing daemon (flowd) crash and thereby a Denial of Service (DoS). Continued receipt of these specific packets will cause a sustained Denial of Service condition. This issue occurs when SIP ALG is enabled and specific SIP messages are processed simultaneously. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on MX Series, or SRX Series.

An Improper Check for Unusual or Exceptional Conditions vulnerability in BGP route processing of Juniper Networks Junos OS and Junos OS Evolved allows an attacker to cause Routing Protocol Daemon (RPD) crash by sending a BGP route with invalid next-hop resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems without import policy configured. This issue affects: Juniper Networks Junos OS 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. Juniper Networks Junos OS Evolved 21.4-EVO versions prior to 21.4R2-S2-EVO, 21.4R3-EVO; 22.1-EVO versions prior to 22.1R1-S2-EVO, 22.1R2-EVO; 22.2-EVO versions prior to 22.2R1-S1-EVO, 22.2R2-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 21.1R1. Juniper Networks Junos OS Evolved versions prior to 21.3R1-EVO.