In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Modify the print level of CQE error Too much print may lead to a panic in kernel. Change ibdev_err() to ibdev_err_ratelimited(), and change the printing level of cqe dump to debug level.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpi3mr: Fix corrupt config pages PHY state is switched in sysfs The driver, through the SAS transport, exposes a sysfs interface to enable/disable PHYs in a controller/expander setup. When multiple PHYs are disabled and enabled in rapid succession, the persistent and current config pages related to SAS IO unit/SAS Expander pages could get corrupted. Use separate memory for each config request.

In the Linux kernel, the following vulnerability has been resolved: drm/vc4: hdmi: Avoid hang with debug registers when suspended Trying to read /sys/kernel/debug/dri/1/hdmi1_regs when the hdmi is disconnected results in a fatal system hang. This is due to the pm suspend code disabling the dvp clock. That is just a gate of the 108MHz clock in DVP_HT_RPI_MISC_CONFIG, which results in accesses hanging AXI bus. Protect against this.

In the Linux kernel, the following vulnerability has been resolved: ASoC: Intel: sof_sdw: Add space for a terminator into DAIs array The code uses the initialised member of the asoc_sdw_dailink struct to determine if a member of the array is in use. However in the case the array is completely full this will lead to an access 1 past the end of the array, expand the array by one entry to include a space for a terminator.

In the Linux kernel, the following vulnerability has been resolved: genirq/irqdesc: Prevent use-after-free in irq_find_at_or_after() irq_find_at_or_after() dereferences the interrupt descriptor which is returned by mt_find() while neither holding sparse_irq_lock nor RCU read lock, which means the descriptor can be freed between mt_find() and the dereference: CPU0 CPU1 desc = mt_find() delayed_free_desc(desc) irq_desc_get_irq(desc) The use-after-free is reported by KASAN: Call trace: irq_get_next_irq+0x58/0x84 show_stat+0x638/0x824 seq_read_iter+0x158/0x4ec proc_reg_read_iter+0x94/0x12c vfs_read+0x1e0/0x2c8 Freed by task 4471: slab_free_freelist_hook+0x174/0x1e0 __kmem_cache_free+0xa4/0x1dc kfree+0x64/0x128 irq_kobj_release+0x28/0x3c kobject_put+0xcc/0x1e0 delayed_free_desc+0x14/0x2c rcu_do_batch+0x214/0x720 Guard the access with a RCU read lock section.

An issue was discovered in net/netfilter/nf_tables_api.c in the Linux kernel before 5.19.6. A denial of service can occur upon binding to an already bound chain.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Use 64 bit variable to avoid 32 bit overflow For example, in the expression: vbo = 2 * vbo + skip

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: connac: check for null before dereferencing The wcid can be NULL. It should be checked for validity before dereferencing it to avoid crash.

In the Linux kernel, the following vulnerability has been resolved: ila: do not generate empty messages in ila_xlat_nl_cmd_get_mapping() ila_xlat_nl_cmd_get_mapping() generates an empty skb, triggerring a recent sanity check [1]. Instead, return an error code, so that user space can get it. [1] skb_assert_len WARNING: CPU: 0 PID: 5923 at include/linux/skbuff.h:2527 skb_assert_len include/linux/skbuff.h:2527 [inline] WARNING: CPU: 0 PID: 5923 at include/linux/skbuff.h:2527 __dev_queue_xmit+0x1bc0/0x3488 net/core/dev.c:4156 Modules linked in: CPU: 0 PID: 5923 Comm: syz-executor269 Not tainted 6.2.0-syzkaller-18300-g2ebd1fbb946d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/21/2023 pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : skb_assert_len include/linux/skbuff.h:2527 [inline] pc : __dev_queue_xmit+0x1bc0/0x3488 net/core/dev.c:4156 lr : skb_assert_len include/linux/skbuff.h:2527 [inline] lr : __dev_queue_xmit+0x1bc0/0x3488 net/core/dev.c:4156 sp : ffff80001e0d6c40 x29: ffff80001e0d6e60 x28: dfff800000000000 x27: ffff0000c86328c0 x26: dfff800000000000 x25: ffff0000c8632990 x24: ffff0000c8632a00 x23: 0000000000000000 x22: 1fffe000190c6542 x21: ffff0000c8632a10 x20: ffff0000c8632a00 x19: ffff80001856e000 x18: ffff80001e0d5fc0 x17: 0000000000000000 x16: ffff80001235d16c x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000001 x12: 0000000000000001 x11: ff80800008353a30 x10: 0000000000000000 x9 : 21567eaf25bfb600 x8 : 21567eaf25bfb600 x7 : 0000000000000001 x6 : 0000000000000001 x5 : ffff80001e0d6558 x4 : ffff800015c74760 x3 : ffff800008596744 x2 : 0000000000000001 x1 : 0000000100000000 x0 : 000000000000000e Call trace: skb_assert_len include/linux/skbuff.h:2527 [inline] __dev_queue_xmit+0x1bc0/0x3488 net/core/dev.c:4156 dev_queue_xmit include/linux/netdevice.h:3033 [inline] __netlink_deliver_tap_skb net/netlink/af_netlink.c:307 [inline] __netlink_deliver_tap+0x45c/0x6f8 net/netlink/af_netlink.c:325 netlink_deliver_tap+0xf4/0x174 net/netlink/af_netlink.c:338 __netlink_sendskb net/netlink/af_netlink.c:1283 [inline] netlink_sendskb+0x6c/0x154 net/netlink/af_netlink.c:1292 netlink_unicast+0x334/0x8d4 net/netlink/af_netlink.c:1380 nlmsg_unicast include/net/netlink.h:1099 [inline] genlmsg_unicast include/net/genetlink.h:433 [inline] genlmsg_reply include/net/genetlink.h:443 [inline] ila_xlat_nl_cmd_get_mapping+0x620/0x7d0 net/ipv6/ila/ila_xlat.c:493 genl_family_rcv_msg_doit net/netlink/genetlink.c:968 [inline] genl_family_rcv_msg net/netlink/genetlink.c:1048 [inline] genl_rcv_msg+0x938/0xc1c net/netlink/genetlink.c:1065 netlink_rcv_skb+0x214/0x3c4 net/netlink/af_netlink.c:2574 genl_rcv+0x38/0x50 net/netlink/genetlink.c:1076 netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline] netlink_unicast+0x660/0x8d4 net/netlink/af_netlink.c:1365 netlink_sendmsg+0x800/0xae0 net/netlink/af_netlink.c:1942 sock_sendmsg_nosec net/socket.c:714 [inline] sock_sendmsg net/socket.c:734 [inline] ____sys_sendmsg+0x558/0x844 net/socket.c:2479 ___sys_sendmsg net/socket.c:2533 [inline] __sys_sendmsg+0x26c/0x33c net/socket.c:2562 __do_sys_sendmsg net/socket.c:2571 [inline] __se_sys_sendmsg net/socket.c:2569 [inline] __arm64_sys_sendmsg+0x80/0x94 net/socket.c:2569 __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline] invoke_syscall+0x98/0x2c0 arch/arm64/kernel/syscall.c:52 el0_svc_common+0x138/0x258 arch/arm64/kernel/syscall.c:142 do_el0_svc+0x64/0x198 arch/arm64/kernel/syscall.c:193 el0_svc+0x58/0x168 arch/arm64/kernel/entry-common.c:637 el0t_64_sync_handler+0x84/0xf0 arch/arm64/kernel/entry-common.c:655 el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:591 irq event stamp: 136484 hardirqs last enabled at (136483): [<ffff800008350244>] __up_console_sem+0x60/0xb4 kernel/printk/printk.c:345 hardirqs last disabled at (136484): [<ffff800012358d60>] el1_dbg+0x24/0x80 arch/arm64/kernel/entry-common.c:405 softirqs last enabled at (136418): [<ffff800008020ea8>] softirq_ha ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drivers/perf: hisi: hns3: Actually use devm_add_action_or_reset() pci_alloc_irq_vectors() allocates an irq vector. When devm_add_action() fails, the irq vector is not freed, which leads to a memory leak. Replace the devm_add_action with devm_add_action_or_reset to ensure the irq vector can be destroyed when it fails.

In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Fix general protection fault in ivpu_bo_list() Check if ctx is not NULL before accessing its fields.

A memory out-of-bounds read flaw was found in the Linux kernel before 5.9-rc2 with the ext3/ext4 file system, in the way it accesses a directory with broken indexing. This flaw allows a local user to crash the system if the directory exists. The highest threat from this vulnerability is to system availability.

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: move the EST lock to struct stmmac_priv Reinitialize the whole EST structure would also reset the mutex lock which is embedded in the EST structure, and then trigger the following warning. To address this, move the lock to struct stmmac_priv. We also need to reacquire the mutex lock when doing this initialization. DEBUG_LOCKS_WARN_ON(lock->magic != lock) WARNING: CPU: 3 PID: 505 at kernel/locking/mutex.c:587 __mutex_lock+0xd84/0x1068 Modules linked in: CPU: 3 PID: 505 Comm: tc Not tainted 6.9.0-rc6-00053-g0106679839f7-dirty #29 Hardware name: NXP i.MX8MPlus EVK board (DT) pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __mutex_lock+0xd84/0x1068 lr : __mutex_lock+0xd84/0x1068 sp : ffffffc0864e3570 x29: ffffffc0864e3570 x28: ffffffc0817bdc78 x27: 0000000000000003 x26: ffffff80c54f1808 x25: ffffff80c9164080 x24: ffffffc080d723ac x23: 0000000000000000 x22: 0000000000000002 x21: 0000000000000000 x20: 0000000000000000 x19: ffffffc083bc3000 x18: ffffffffffffffff x17: ffffffc08117b080 x16: 0000000000000002 x15: ffffff80d2d40000 x14: 00000000000002da x13: ffffff80d2d404b8 x12: ffffffc082b5a5c8 x11: ffffffc082bca680 x10: ffffffc082bb2640 x9 : ffffffc082bb2698 x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001 x5 : ffffff8178fe0d48 x4 : 0000000000000000 x3 : 0000000000000027 x2 : ffffff8178fe0d50 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: __mutex_lock+0xd84/0x1068 mutex_lock_nested+0x28/0x34 tc_setup_taprio+0x118/0x68c stmmac_setup_tc+0x50/0xf0 taprio_change+0x868/0xc9c

In the Linux kernel, the following vulnerability has been resolved: libbpf: Prevent null-pointer dereference when prog to load has no BTF In bpf_objec_load_prog(), there's no guarantee that obj->btf is non-NULL when passing it to btf__fd(), and this function does not perform any check before dereferencing its argument (as bpf_object__btf_fd() used to do). As a consequence, we get segmentation fault errors in bpftool (for example) when trying to load programs that come without BTF information. v2: Keep btf__fd() in the fix instead of reverting to bpf_object__btf_fd().

In the Linux kernel, the following vulnerability has been resolved: drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails Calling a6xx_destroy() before adreno_gpu_init() leads to a null pointer dereference on: msm_gpu_cleanup() : platform_set_drvdata(gpu->pdev, NULL); as gpu->pdev is only assigned in: a6xx_gpu_init() |_ adreno_gpu_init |_ msm_gpu_init() Instead of relying on handwavy null checks down the cleanup chain, explicitly de-allocate the LLC data and free a6xx_gpu instead. Patchwork: https://patchwork.freedesktop.org/patch/588919/

Uncontrolled resource consumption in some Intel(R) Aptio* V UEFI Firmware Integrator Tools may allow an authenticated user to potentially enable denial of service via local access.

In the Linux kernel, the following vulnerability has been resolved: fsdax: force clear dirty mark if CoW XFS allows CoW on non-shared extents to combat fragmentation[1]. The old non-shared extent could be mwrited before, its dax entry is marked dirty. This results in a WARNing: [ 28.512349] ------------[ cut here ]------------ [ 28.512622] WARNING: CPU: 2 PID: 5255 at fs/dax.c:390 dax_insert_entry+0x342/0x390 [ 28.513050] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 nfs lockd grace fscache netfs nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables [ 28.515462] CPU: 2 PID: 5255 Comm: fsstress Kdump: loaded Not tainted 6.3.0-rc1-00001-g85e1481e19c1-dirty #117 [ 28.515902] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS Arch Linux 1.16.1-1-1 04/01/2014 [ 28.516307] RIP: 0010:dax_insert_entry+0x342/0x390 [ 28.516536] Code: 30 5b 5d 41 5c 41 5d 41 5e 41 5f c3 cc cc cc cc 48 8b 45 20 48 83 c0 01 e9 e2 fe ff ff 48 8b 45 20 48 83 c0 01 e9 cd fe ff ff <0f> 0b e9 53 ff ff ff 48 8b 7c 24 08 31 f6 e8 1b 61 a1 00 eb 8c 48 [ 28.517417] RSP: 0000:ffffc9000845fb18 EFLAGS: 00010086 [ 28.517721] RAX: 0000000000000053 RBX: 0000000000000155 RCX: 000000000018824b [ 28.518113] RDX: 0000000000000000 RSI: ffffffff827525a6 RDI: 00000000ffffffff [ 28.518515] RBP: ffffea00062092c0 R08: 0000000000000000 R09: ffffc9000845f9c8 [ 28.518905] R10: 0000000000000003 R11: ffffffff82ddb7e8 R12: 0000000000000155 [ 28.519301] R13: 0000000000000000 R14: 000000000018824b R15: ffff88810cfa76b8 [ 28.519703] FS: 00007f14a0c94740(0000) GS:ffff88817bd00000(0000) knlGS:0000000000000000 [ 28.520148] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 28.520472] CR2: 00007f14a0c8d000 CR3: 000000010321c004 CR4: 0000000000770ee0 [ 28.520863] PKRU: 55555554 [ 28.521043] Call Trace: [ 28.521219] <TASK> [ 28.521368] dax_fault_iter+0x196/0x390 [ 28.521595] dax_iomap_pte_fault+0x19b/0x3d0 [ 28.521852] __xfs_filemap_fault+0x234/0x2b0 [ 28.522116] __do_fault+0x30/0x130 [ 28.522334] do_fault+0x193/0x340 [ 28.522586] __handle_mm_fault+0x2d3/0x690 [ 28.522975] handle_mm_fault+0xe6/0x2c0 [ 28.523259] do_user_addr_fault+0x1bc/0x6f0 [ 28.523521] exc_page_fault+0x60/0x140 [ 28.523763] asm_exc_page_fault+0x22/0x30 [ 28.524001] RIP: 0033:0x7f14a0b589ca [ 28.524225] Code: c5 fe 7f 07 c5 fe 7f 47 20 c5 fe 7f 47 40 c5 fe 7f 47 60 c5 f8 77 c3 66 0f 1f 84 00 00 00 00 00 40 0f b6 c6 48 89 d1 48 89 fa <f3> aa 48 89 d0 c5 f8 77 c3 66 66 2e 0f 1f 84 00 00 00 00 00 66 90 [ 28.525198] RSP: 002b:00007fff1dea1c98 EFLAGS: 00010202 [ 28.525505] RAX: 000000000000001e RBX: 000000000014a000 RCX: 0000000000006046 [ 28.525895] RDX: 00007f14a0c82000 RSI: 000000000000001e RDI: 00007f14a0c8d000 [ 28.526290] RBP: 000000000000006f R08: 0000000000000004 R09: 000000000014a000 [ 28.526681] R10: 0000000000000008 R11: 0000000000000246 R12: 028f5c28f5c28f5c [ 28.527067] R13: 8f5c28f5c28f5c29 R14: 0000000000011046 R15: 00007f14a0c946c0 [ 28.527449] </TASK> [ 28.527600] ---[ end trace 0000000000000000 ]--- To be able to delete this entry, clear its dirty mark before invalidate_inode_pages2_range(). [1] https://lore.kernel.org/linux-xfs/20230321151339.GA11376@frogsfrogsfrogs/

In the Linux kernel, the following vulnerability has been resolved: ice: fix crash on probe for DPLL enabled E810 LOM The E810 Lan On Motherboard (LOM) design is vendor specific. Intel provides the reference design, but it is up to vendor on the final product design. For some cases, like Linux DPLL support, the static values defined in the driver does not reflect the actual LOM design. Current implementation of dpll pins is causing the crash on probe of the ice driver for such DPLL enabled E810 LOM designs: WARNING: (...) at drivers/dpll/dpll_core.c:495 dpll_pin_get+0x2c4/0x330 ... Call Trace: <TASK> ? __warn+0x83/0x130 ? dpll_pin_get+0x2c4/0x330 ? report_bug+0x1b7/0x1d0 ? handle_bug+0x42/0x70 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? dpll_pin_get+0x117/0x330 ? dpll_pin_get+0x2c4/0x330 ? dpll_pin_get+0x117/0x330 ice_dpll_get_pins.isra.0+0x52/0xe0 [ice] ... The number of dpll pins enabled by LOM vendor is greater than expected and defined in the driver for Intel designed NICs, which causes the crash. Prevent the crash and allow generic pin initialization within Linux DPLL subsystem for DPLL enabled E810 LOM designs. Newly designed solution for described issue will be based on "per HW design" pin initialization. It requires pin information dynamically acquired from the firmware and is already in progress, planned for next-tree only.

In the Linux kernel, the following vulnerability has been resolved: mm/slab: fix warning caused by duplicate kmem_cache creation in kmem_buckets_create Commit b035f5a6d852 ("mm: slab: reduce the kmalloc() minimum alignment if DMA bouncing possible") reduced ARCH_KMALLOC_MINALIGN to 8 on arm64. However, with KASAN_HW_TAGS enabled, arch_slab_minalign() becomes 16. This causes kmalloc_caches[*][8] to be aliased to kmalloc_caches[*][16], resulting in kmem_buckets_create() attempting to create a kmem_cache for size 16 twice. This duplication triggers warnings on boot: [ 2.325108] ------------[ cut here ]------------ [ 2.325135] kmem_cache of name 'memdup_user-16' already exists [ 2.325783] WARNING: CPU: 0 PID: 1 at mm/slab_common.c:107 __kmem_cache_create_args+0xb8/0x3b0 [ 2.327957] Modules linked in: [ 2.328550] CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.0-rc5mm-unstable-arm64+ #12 [ 2.328683] Hardware name: QEMU QEMU Virtual Machine, BIOS 2024.02-2 03/11/2024 [ 2.328790] pstate: 61000009 (nZCv daif -PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 2.328911] pc : __kmem_cache_create_args+0xb8/0x3b0 [ 2.328930] lr : __kmem_cache_create_args+0xb8/0x3b0 [ 2.328942] sp : ffff800083d6fc50 [ 2.328961] x29: ffff800083d6fc50 x28: f2ff0000c1674410 x27: ffff8000820b0598 [ 2.329061] x26: 000000007fffffff x25: 0000000000000010 x24: 0000000000002000 [ 2.329101] x23: ffff800083d6fce8 x22: ffff8000832222e8 x21: ffff800083222388 [ 2.329118] x20: f2ff0000c1674410 x19: f5ff0000c16364c0 x18: ffff800083d80030 [ 2.329135] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 2.329152] x14: 0000000000000000 x13: 0a73747369786520 x12: 79646165726c6120 [ 2.329169] x11: 656820747563205b x10: 2d2d2d2d2d2d2d2d x9 : 0000000000000000 [ 2.329194] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 [ 2.329210] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 [ 2.329226] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 [ 2.329291] Call trace: [ 2.329407] __kmem_cache_create_args+0xb8/0x3b0 [ 2.329499] kmem_buckets_create+0xfc/0x320 [ 2.329526] init_user_buckets+0x34/0x78 [ 2.329540] do_one_initcall+0x64/0x3c8 [ 2.329550] kernel_init_freeable+0x26c/0x578 [ 2.329562] kernel_init+0x3c/0x258 [ 2.329574] ret_from_fork+0x10/0x20 [ 2.329698] ---[ end trace 0000000000000000 ]--- [ 2.403704] ------------[ cut here ]------------ [ 2.404716] kmem_cache of name 'msg_msg-16' already exists [ 2.404801] WARNING: CPU: 2 PID: 1 at mm/slab_common.c:107 __kmem_cache_create_args+0xb8/0x3b0 [ 2.404842] Modules linked in: [ 2.404971] CPU: 2 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.12.0-rc5mm-unstable-arm64+ #12 [ 2.405026] Tainted: [W]=WARN [ 2.405043] Hardware name: QEMU QEMU Virtual Machine, BIOS 2024.02-2 03/11/2024 [ 2.405057] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 2.405079] pc : __kmem_cache_create_args+0xb8/0x3b0 [ 2.405100] lr : __kmem_cache_create_args+0xb8/0x3b0 [ 2.405111] sp : ffff800083d6fc50 [ 2.405115] x29: ffff800083d6fc50 x28: fbff0000c1674410 x27: ffff8000820b0598 [ 2.405135] x26: 000000000000ffd0 x25: 0000000000000010 x24: 0000000000006000 [ 2.405153] x23: ffff800083d6fce8 x22: ffff8000832222e8 x21: ffff800083222388 [ 2.405169] x20: fbff0000c1674410 x19: fdff0000c163d6c0 x18: ffff800083d80030 [ 2.405185] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 2.405201] x14: 0000000000000000 x13: 0a73747369786520 x12: 79646165726c6120 [ 2.405217] x11: 656820747563205b x10: 2d2d2d2d2d2d2d2d x9 : 0000000000000000 [ 2.405233] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 [ 2.405248] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 [ 2.405271] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 [ 2.405287] Call trace: [ 2 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Move events notifier registration to be after device registration Move pkey change work initialization and cleanup from device resources stage to notifier stage, since this is the stage which handles this work events. Fix a race between the device deregistration and pkey change work by moving MLX5_IB_STAGE_DEVICE_NOTIFIER to be after MLX5_IB_STAGE_IB_REG in order to ensure that the notifier is deregistered before the device during cleanup. Which ensures there are no works that are being executed after the device has already unregistered which can cause the panic below. BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 1 PID: 630071 Comm: kworker/1:2 Kdump: loaded Tainted: G W OE --------- --- 5.14.0-162.6.1.el9_1.x86_64 #1 Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS 090008 02/27/2023 Workqueue: events pkey_change_handler [mlx5_ib] RIP: 0010:setup_qp+0x38/0x1f0 [mlx5_ib] Code: ee 41 54 45 31 e4 55 89 f5 53 48 89 fb 48 83 ec 20 8b 77 08 65 48 8b 04 25 28 00 00 00 48 89 44 24 18 48 8b 07 48 8d 4c 24 16 <4c> 8b 38 49 8b 87 80 0b 00 00 4c 89 ff 48 8b 80 08 05 00 00 8b 40 RSP: 0018:ffffbcc54068be20 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff954054494128 RCX: ffffbcc54068be36 RDX: ffff954004934000 RSI: 0000000000000001 RDI: ffff954054494128 RBP: 0000000000000023 R08: ffff954001be2c20 R09: 0000000000000001 R10: ffff954001be2c20 R11: ffff9540260133c0 R12: 0000000000000000 R13: 0000000000000023 R14: 0000000000000000 R15: ffff9540ffcb0905 FS: 0000000000000000(0000) GS:ffff9540ffc80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 000000010625c001 CR4: 00000000003706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: mlx5_ib_gsi_pkey_change+0x20/0x40 [mlx5_ib] process_one_work+0x1e8/0x3c0 worker_thread+0x50/0x3b0 ? rescuer_thread+0x380/0x380 kthread+0x149/0x170 ? set_kthread_struct+0x50/0x50 ret_from_fork+0x22/0x30 Modules linked in: rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) mlx5_ib(OE) mlx5_fwctl(OE) fwctl(OE) ib_uverbs(OE) mlx5_core(OE) mlxdevm(OE) ib_core(OE) mlx_compat(OE) psample mlxfw(OE) tls knem(OE) netconsole nfsv3 nfs_acl nfs lockd grace fscache netfs qrtr rfkill sunrpc intel_rapl_msr intel_rapl_common rapl hv_balloon hv_utils i2c_piix4 pcspkr joydev fuse ext4 mbcache jbd2 sr_mod sd_mod cdrom t10_pi sg ata_generic pci_hyperv pci_hyperv_intf hyperv_drm drm_shmem_helper drm_kms_helper hv_storvsc syscopyarea hv_netvsc sysfillrect sysimgblt hid_hyperv fb_sys_fops scsi_transport_fc hyperv_keyboard drm ata_piix crct10dif_pclmul crc32_pclmul crc32c_intel libata ghash_clmulni_intel hv_vmbus serio_raw [last unloaded: ib_core] CR2: 0000000000000000 ---[ end trace f6f8be4eae12f7bc ]---

In the Linux kernel, the following vulnerability has been resolved: lib/test_hmm.c: handle src_pfns and dst_pfns allocation failure The kcalloc() in dmirror_device_evict_chunk() will return null if the physical memory has run out. As a result, if src_pfns or dst_pfns is dereferenced, the null pointer dereference bug will happen. Moreover, the device is going away. If the kcalloc() fails, the pages mapping a chunk could not be evicted. So add a __GFP_NOFAIL flag in kcalloc(). Finally, as there is no need to have physically contiguous memory, Switch kcalloc() to kvcalloc() in order to avoid failing allocations.

In the Linux kernel, the following vulnerability has been resolved: drm: vc4: Fix possible null pointer dereference In vc4_hdmi_audio_init() of_get_address() may return NULL which is later dereferenced. Fix this bug by adding NULL check. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: vfio/pci: fix potential memory leak in vfio_intx_enable() If vfio_irq_ctx_alloc() failed will lead to 'name' memory leak.

In the Linux kernel, the following vulnerability has been resolved: mptcp: init: protect sched with rcu_read_lock Enabling CONFIG_PROVE_RCU_LIST with its dependence CONFIG_RCU_EXPERT creates this splat when an MPTCP socket is created: ============================= WARNING: suspicious RCU usage 6.12.0-rc2+ #11 Not tainted ----------------------------- net/mptcp/sched.c:44 RCU-list traversed in non-reader section!! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 no locks held by mptcp_connect/176. stack backtrace: CPU: 0 UID: 0 PID: 176 Comm: mptcp_connect Not tainted 6.12.0-rc2+ #11 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:123) lockdep_rcu_suspicious (kernel/locking/lockdep.c:6822) mptcp_sched_find (net/mptcp/sched.c:44 (discriminator 7)) mptcp_init_sock (net/mptcp/protocol.c:2867 (discriminator 1)) ? sock_init_data_uid (arch/x86/include/asm/atomic.h:28) inet_create.part.0.constprop.0 (net/ipv4/af_inet.c:386) ? __sock_create (include/linux/rcupdate.h:347 (discriminator 1)) __sock_create (net/socket.c:1576) __sys_socket (net/socket.c:1671) ? __pfx___sys_socket (net/socket.c:1712) ? do_user_addr_fault (arch/x86/mm/fault.c:1419 (discriminator 1)) __x64_sys_socket (net/socket.c:1728) do_syscall_64 (arch/x86/entry/common.c:52 (discriminator 1)) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) That's because when the socket is initialised, rcu_read_lock() is not used despite the explicit comment written above the declaration of mptcp_sched_find() in sched.c. Adding the missing lock/unlock avoids the warning.

In the Linux kernel, the following vulnerability has been resolved: media: atomisp: ssh_css: Fix a null-pointer dereference in load_video_binaries The allocation failure of mycs->yuv_scaler_binary in load_video_binaries() is followed with a dereference of mycs->yuv_scaler_binary after the following call chain: sh_css_pipe_load_binaries() |-> load_video_binaries(mycs->yuv_scaler_binary == NULL) | |-> sh_css_pipe_unload_binaries() |-> unload_video_binaries() In unload_video_binaries(), it calls to ia_css_binary_unload with argument &pipe->pipe_settings.video.yuv_scaler_binary[i], which refers to the same memory slot as mycs->yuv_scaler_binary. Thus, a null-pointer dereference is triggered.

In the Linux kernel, the following vulnerability has been resolved: serial: max3100: Update uart_driver_registered on driver removal The removal of the last MAX3100 device triggers the removal of the driver. However, code doesn't update the respective global variable and after insmod — rmmod — insmod cycle the kernel oopses: max3100 spi-PRP0001:01: max3100_probe: adding port 0 BUG: kernel NULL pointer dereference, address: 0000000000000408 ... RIP: 0010:serial_core_register_port+0xa0/0x840 ... max3100_probe+0x1b6/0x280 [max3100] spi_probe+0x8d/0xb0 Update the actual state so next time UART driver will be registered again. Hugo also noticed, that the error path in the probe also affected by having the variable set, and not cleared. Instead of clearing it move the assignment after the successfull uart_register_driver() call.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Track xmit submission to PTP WQ after populating metadata map Ensure the skb is available in metadata mapping to skbs before tracking the metadata index for detecting undelivered CQEs. If the metadata index is put in the tracking list before putting the skb in the map, the metadata index might be used for detecting undelivered CQEs before the relevant skb is available in the map, which can lead to a null-ptr-deref. Log: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f] CPU: 0 PID: 1243 Comm: kworker/0:2 Not tainted 6.6.0-rc4+ #108 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: events mlx5e_rx_dim_work [mlx5_core] RIP: 0010:mlx5e_ptp_napi_poll+0x9a4/0x2290 [mlx5_core] Code: 8c 24 38 cc ff ff 4c 8d 3c c1 4c 89 f9 48 c1 e9 03 42 80 3c 31 00 0f 85 97 0f 00 00 4d 8b 3f 49 8d 7f 28 48 89 f9 48 c1 e9 03 <42> 80 3c 31 00 0f 85 8b 0f 00 00 49 8b 47 28 48 85 c0 0f 84 05 07 RSP: 0018:ffff8884d3c09c88 EFLAGS: 00010206 RAX: 0000000000000069 RBX: ffff8881160349d8 RCX: 0000000000000005 RDX: ffffed10218f48cf RSI: 0000000000000004 RDI: 0000000000000028 RBP: ffff888122707700 R08: 0000000000000001 R09: ffffed109a781383 R10: 0000000000000003 R11: 0000000000000003 R12: ffff88810c7a7a40 R13: ffff888122707700 R14: dffffc0000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8884d3c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f4f878dd6e0 CR3: 000000014d108002 CR4: 0000000000370eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> ? die_addr+0x3c/0xa0 ? exc_general_protection+0x144/0x210 ? asm_exc_general_protection+0x22/0x30 ? mlx5e_ptp_napi_poll+0x9a4/0x2290 [mlx5_core] ? mlx5e_ptp_napi_poll+0x8f6/0x2290 [mlx5_core] __napi_poll.constprop.0+0xa4/0x580 net_rx_action+0x460/0xb80 ? _raw_spin_unlock_irqrestore+0x32/0x60 ? __napi_poll.constprop.0+0x580/0x580 ? tasklet_action_common.isra.0+0x2ef/0x760 __do_softirq+0x26c/0x827 irq_exit_rcu+0xc2/0x100 common_interrupt+0x7f/0xa0 </IRQ> <TASK> asm_common_interrupt+0x22/0x40 RIP: 0010:__kmem_cache_alloc_node+0xb/0x330 Code: 41 5d 41 5e 41 5f c3 8b 44 24 14 8b 4c 24 10 09 c8 eb d5 e8 b7 43 ca 01 0f 1f 80 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41 57 <41> 56 41 89 d6 41 55 41 89 f5 41 54 49 89 fc 53 48 83 e4 f0 48 83 RSP: 0018:ffff88812c4079c0 EFLAGS: 00000246 RAX: 1ffffffff083c7fe RBX: ffff888100042dc0 RCX: 0000000000000218 RDX: 00000000ffffffff RSI: 0000000000000dc0 RDI: ffff888100042dc0 RBP: ffff88812c4079c8 R08: ffffffffa0289f96 R09: ffffed1025880ea9 R10: ffff888138839f80 R11: 0000000000000002 R12: 0000000000000dc0 R13: 0000000000000100 R14: 000000000000008c R15: ffff8881271fc450 ? cmd_exec+0x796/0x2200 [mlx5_core] kmalloc_trace+0x26/0xc0 cmd_exec+0x796/0x2200 [mlx5_core] mlx5_cmd_do+0x22/0xc0 [mlx5_core] mlx5_cmd_exec+0x17/0x30 [mlx5_core] mlx5_core_modify_cq_moderation+0x139/0x1b0 [mlx5_core] ? mlx5_add_cq_to_tasklet+0x280/0x280 [mlx5_core] ? lockdep_set_lock_cmp_fn+0x190/0x190 ? process_one_work+0x659/0x1220 mlx5e_rx_dim_work+0x9d/0x100 [mlx5_core] process_one_work+0x730/0x1220 ? lockdep_hardirqs_on_prepare+0x400/0x400 ? max_active_store+0xf0/0xf0 ? assign_work+0x168/0x240 worker_thread+0x70f/0x12d0 ? __kthread_parkme+0xd1/0x1d0 ? process_one_work+0x1220/0x1220 kthread+0x2d9/0x3b0 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x2d/0x70 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork_as ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ALSA: Fix deadlocks with kctl removals at disconnection In snd_card_disconnect(), we set card->shutdown flag at the beginning, call callbacks and do sync for card->power_ref_sleep waiters at the end. The callback may delete a kctl element, and this can lead to a deadlock when the device was in the suspended state. Namely: * A process waits for the power up at snd_power_ref_and_wait() in snd_ctl_info() or read/write() inside card->controls_rwsem. * The system gets disconnected meanwhile, and the driver tries to delete a kctl via snd_ctl_remove*(); it tries to take card->controls_rwsem again, but this is already locked by the above. Since the sleeper isn't woken up, this deadlocks. An easy fix is to wake up sleepers before processing the driver disconnect callbacks but right after setting the card->shutdown flag. Then all sleepers will abort immediately, and the code flows again. So, basically this patch moves the wait_event() call at the right timing. While we're at it, just to be sure, call wait_event_all() instead of wait_event(), although we don't use exclusive events on this queue for now.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: u_audio: Fix race condition use of controls after free during gadget unbind. Hang on to the control IDs instead of pointers since those are correctly handled with locks.

In the Linux kernel, the following vulnerability has been resolved: Fix page corruption caused by racy check in __free_pages When we upgraded our kernel, we started seeing some page corruption like the following consistently: BUG: Bad page state in process ganesha.nfsd pfn:1304ca page:0000000022261c55 refcount:0 mapcount:-128 mapping:0000000000000000 index:0x0 pfn:0x1304ca flags: 0x17ffffc0000000() raw: 0017ffffc0000000 ffff8a513ffd4c98 ffffeee24b35ec08 0000000000000000 raw: 0000000000000000 0000000000000001 00000000ffffff7f 0000000000000000 page dumped because: nonzero mapcount CPU: 0 PID: 15567 Comm: ganesha.nfsd Kdump: loaded Tainted: P B O 5.10.158-1.nutanix.20221209.el7.x86_64 #1 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/05/2016 Call Trace: dump_stack+0x74/0x96 bad_page.cold+0x63/0x94 check_new_page_bad+0x6d/0x80 rmqueue+0x46e/0x970 get_page_from_freelist+0xcb/0x3f0 ? _cond_resched+0x19/0x40 __alloc_pages_nodemask+0x164/0x300 alloc_pages_current+0x87/0xf0 skb_page_frag_refill+0x84/0x110 ... Sometimes, it would also show up as corruption in the free list pointer and cause crashes. After bisecting the issue, we found the issue started from commit e320d3012d25 ("mm/page_alloc.c: fix freeing non-compound pages"): if (put_page_testzero(page)) free_the_page(page, order); else if (!PageHead(page)) while (order-- > 0) free_the_page(page + (1 << order), order); So the problem is the check PageHead is racy because at this point we already dropped our reference to the page. So even if we came in with compound page, the page can already be freed and PageHead can return false and we will end up freeing all the tail pages causing double free.

In the Linux kernel, the following vulnerability has been resolved: block: refine the EOF check in blkdev_iomap_begin blkdev_iomap_begin rounds down the offset to the logical block size before stashing it in iomap->offset and checking that it still is inside the inode size. Check the i_size check to the raw pos value so that we don't try a zero size write if iter->pos is unaligned.

In the Linux kernel, the following vulnerability has been resolved: serial: max3100: Lock port->lock when calling uart_handle_cts_change() uart_handle_cts_change() has to be called with port lock taken, Since we run it in a separate work, the lock may not be taken at the time of running. Make sure that it's taken by explicitly doing that. Without it we got a splat: WARNING: CPU: 0 PID: 10 at drivers/tty/serial/serial_core.c:3491 uart_handle_cts_change+0xa6/0xb0 ... Workqueue: max3100-0 max3100_work [max3100] RIP: 0010:uart_handle_cts_change+0xa6/0xb0 ... max3100_handlerx+0xc5/0x110 [max3100] max3100_work+0x12a/0x340 [max3100]

In the Linux kernel, the following vulnerability has been resolved: bpf: Add BPF_PROG_TYPE_CGROUP_SKB attach type enforcement in BPF_LINK_CREATE bpf_prog_attach uses attach_type_to_prog_type to enforce proper attach type for BPF_PROG_TYPE_CGROUP_SKB. link_create uses bpf_prog_get and relies on bpf_prog_attach_check_attach_type to properly verify prog_type <> attach_type association. Add missing attach_type enforcement for the link_create case. Otherwise, it's currently possible to attach cgroup_skb prog types to other cgroup hooks.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: HCI: Remove HCI_AMP support Since BT_HS has been remove HCI_AMP controllers no longer has any use so remove it along with the capability of creating AMP controllers. Since we no longer need to differentiate between AMP and Primary controllers, as only HCI_PRIMARY is left, this also remove hdev->dev_type altogether.

In the Linux kernel, the following vulnerability has been resolved: blk-cgroup: fix list corruption from resetting io stat Since commit 3b8cc6298724 ("blk-cgroup: Optimize blkcg_rstat_flush()"), each iostat instance is added to blkcg percpu list, so blkcg_reset_stats() can't reset the stat instance by memset(), otherwise the llist may be corrupted. Fix the issue by only resetting the counter part.

In the Linux kernel, the following vulnerability has been resolved: thermal: intel: int340x: processor: Fix warning during module unload The processor_thermal driver uses pcim_device_enable() to enable a PCI device, which means the device will be automatically disabled on driver detach. Thus there is no need to call pci_disable_device() again on it. With recent PCI device resource management improvements, e.g. commit f748a07a0b64 ("PCI: Remove legacy pcim_release()"), this problem is exposed and triggers the warining below. [ 224.010735] proc_thermal_pci 0000:00:04.0: disabling already-disabled device [ 224.010747] WARNING: CPU: 8 PID: 4442 at drivers/pci/pci.c:2250 pci_disable_device+0xe5/0x100 ... [ 224.010844] Call Trace: [ 224.010845] <TASK> [ 224.010847] ? show_regs+0x6d/0x80 [ 224.010851] ? __warn+0x8c/0x140 [ 224.010854] ? pci_disable_device+0xe5/0x100 [ 224.010856] ? report_bug+0x1c9/0x1e0 [ 224.010859] ? handle_bug+0x46/0x80 [ 224.010862] ? exc_invalid_op+0x1d/0x80 [ 224.010863] ? asm_exc_invalid_op+0x1f/0x30 [ 224.010867] ? pci_disable_device+0xe5/0x100 [ 224.010869] ? pci_disable_device+0xe5/0x100 [ 224.010871] ? kfree+0x21a/0x2b0 [ 224.010873] pcim_disable_device+0x20/0x30 [ 224.010875] devm_action_release+0x16/0x20 [ 224.010878] release_nodes+0x47/0xc0 [ 224.010880] devres_release_all+0x9f/0xe0 [ 224.010883] device_unbind_cleanup+0x12/0x80 [ 224.010885] device_release_driver_internal+0x1ca/0x210 [ 224.010887] driver_detach+0x4e/0xa0 [ 224.010889] bus_remove_driver+0x6f/0xf0 [ 224.010890] driver_unregister+0x35/0x60 [ 224.010892] pci_unregister_driver+0x44/0x90 [ 224.010894] proc_thermal_pci_driver_exit+0x14/0x5f0 [processor_thermal_device_pci] ... [ 224.010921] ---[ end trace 0000000000000000 ]--- Remove the excess pci_disable_device() calls. [ rjw: Subject and changelog edits ]

In the Linux kernel, the following vulnerability has been resolved: media: i2c: et8ek8: Don't strip remove function when driver is builtin Using __exit for the remove function results in the remove callback being discarded with CONFIG_VIDEO_ET8EK8=y. When such a device gets unbound (e.g. using sysfs or hotplug), the driver is just removed without the cleanup being performed. This results in resource leaks. Fix it by compiling in the remove callback unconditionally. This also fixes a W=1 modpost warning: WARNING: modpost: drivers/media/i2c/et8ek8/et8ek8: section mismatch in reference: et8ek8_i2c_driver+0x10 (section: .data) -> et8ek8_remove (section: .exit.text)

In the Linux kernel, the following vulnerability has been resolved: net: micrel: Fix receiving the timestamp in the frame for lan8841 The blamed commit started to use the ptp workqueue to get the second part of the timestamp. And when the port was set down, then this workqueue is stopped. But if the config option NETWORK_PHY_TIMESTAMPING is not enabled, then the ptp_clock is not initialized so then it would crash when it would try to access the delayed work. So then basically by setting up and then down the port, it would crash. The fix consists in checking if the ptp_clock is initialized and only then cancel the delayed work.

In the Linux kernel, the following vulnerability has been resolved: f2fs: multidev: fix to recognize valid zero block address As reported by Yi Zhang in mailing list [1], kernel warning was catched during zbd/010 test as below: ./check zbd/010 zbd/010 (test gap zone support with F2FS) [failed] runtime ... 3.752s something found in dmesg: [ 4378.146781] run blktests zbd/010 at 2024-02-18 11:31:13 [ 4378.192349] null_blk: module loaded [ 4378.209860] null_blk: disk nullb0 created [ 4378.413285] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 4378.422334] scsi host15: scsi_debug: version 0191 [20210520] dev_size_mb=1024, opts=0x0, submit_queues=1, statistics=0 [ 4378.434922] scsi 15:0:0:0: Direct-Access-ZBC Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 4378.443343] scsi 15:0:0:0: Power-on or device reset occurred [ 4378.449371] sd 15:0:0:0: Attached scsi generic sg5 type 20 [ 4378.449418] sd 15:0:0:0: [sdf] Host-managed zoned block device ... (See '/mnt/tests/gitlab.com/api/v4/projects/19168116/repository/archive.zip/storage/blktests/blk/blktests/results/nodev/zbd/010.dmesg' WARNING: CPU: 22 PID: 44011 at fs/iomap/iter.c:51 CPU: 22 PID: 44011 Comm: fio Not tainted 6.8.0-rc3+ #1 RIP: 0010:iomap_iter+0x32b/0x350 Call Trace: <TASK> __iomap_dio_rw+0x1df/0x830 f2fs_file_read_iter+0x156/0x3d0 [f2fs] aio_read+0x138/0x210 io_submit_one+0x188/0x8c0 __x64_sys_io_submit+0x8c/0x1a0 do_syscall_64+0x86/0x170 entry_SYSCALL_64_after_hwframe+0x6e/0x76 Shinichiro Kawasaki helps to analyse this issue and proposes a potential fixing patch in [2]. Quoted from reply of Shinichiro Kawasaki: "I confirmed that the trigger commit is dbf8e63f48af as Yi reported. I took a look in the commit, but it looks fine to me. So I thought the cause is not in the commit diff. I found the WARN is printed when the f2fs is set up with multiple devices, and read requests are mapped to the very first block of the second device in the direct read path. In this case, f2fs_map_blocks() and f2fs_map_blocks_cached() modify map->m_pblk as the physical block address from each block device. It becomes zero when it is mapped to the first block of the device. However, f2fs_iomap_begin() assumes that map->m_pblk is the physical block address of the whole f2fs, across the all block devices. It compares map->m_pblk against NULL_ADDR == 0, then go into the unexpected branch and sets the invalid iomap->length. The WARN catches the invalid iomap->length. This WARN is printed even for non-zoned block devices, by following steps. - Create two (non-zoned) null_blk devices memory backed with 128MB size each: nullb0 and nullb1. # mkfs.f2fs /dev/nullb0 -c /dev/nullb1 # mount -t f2fs /dev/nullb0 "${mount_dir}" # dd if=/dev/zero of="${mount_dir}/test.dat" bs=1M count=192 # dd if="${mount_dir}/test.dat" of=/dev/null bs=1M count=192 iflag=direct ..." So, the root cause of this issue is: when multi-devices feature is on, f2fs_map_blocks() may return zero blkaddr in non-primary device, which is a verified valid block address, however, f2fs_iomap_begin() treats it as an invalid block address, and then it triggers the warning in iomap framework code. Finally, as discussed, we decide to use a more simple and direct way that checking (map.m_flags & F2FS_MAP_MAPPED) condition instead of (map.m_pblk != NULL_ADDR) to fix this issue. Thanks a lot for the effort of Yi Zhang and Shinichiro Kawasaki on this issue. [1] https://lore.kernel.org/linux-f2fs-devel/CAHj4cs-kfojYC9i0G73PRkYzcxCTex=-vugRFeP40g_URGvnfQ@mail.gmail.com/ [2] https://lore.kernel.org/linux-f2fs-devel/gngdj77k4picagsfdtiaa7gpgnup6fsgwzsltx6milmhegmjff@iax2n4wvrqye/

In the Linux kernel, the following vulnerability has been resolved: mptcp: avoid deadlock on fallback while reinjecting Jakub reported an MPTCP deadlock at fallback time: WARNING: possible recursive locking detected 6.18.0-rc7-virtme #1 Not tainted -------------------------------------------- mptcp_connect/20858 is trying to acquire lock: ff1100001da18b60 (&msk->fallback_lock){+.-.}-{3:3}, at: __mptcp_try_fallback+0xd8/0x280 but task is already holding lock: ff1100001da18b60 (&msk->fallback_lock){+.-.}-{3:3}, at: __mptcp_retrans+0x352/0xaa0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&msk->fallback_lock); lock(&msk->fallback_lock); *** DEADLOCK *** May be due to missing lock nesting notation 3 locks held by mptcp_connect/20858: #0: ff1100001da18290 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0x114/0x1bc0 #1: ff1100001db40fd0 (k-sk_lock-AF_INET#2){+.+.}-{0:0}, at: __mptcp_retrans+0x2cb/0xaa0 #2: ff1100001da18b60 (&msk->fallback_lock){+.-.}-{3:3}, at: __mptcp_retrans+0x352/0xaa0 stack backtrace: CPU: 0 UID: 0 PID: 20858 Comm: mptcp_connect Not tainted 6.18.0-rc7-virtme #1 PREEMPT(full) Hardware name: Bochs, BIOS Bochs 01/01/2011 Call Trace: <TASK> dump_stack_lvl+0x6f/0xa0 print_deadlock_bug.cold+0xc0/0xcd validate_chain+0x2ff/0x5f0 __lock_acquire+0x34c/0x740 lock_acquire.part.0+0xbc/0x260 _raw_spin_lock_bh+0x38/0x50 __mptcp_try_fallback+0xd8/0x280 mptcp_sendmsg_frag+0x16c2/0x3050 __mptcp_retrans+0x421/0xaa0 mptcp_release_cb+0x5aa/0xa70 release_sock+0xab/0x1d0 mptcp_sendmsg+0xd5b/0x1bc0 sock_write_iter+0x281/0x4d0 new_sync_write+0x3c5/0x6f0 vfs_write+0x65e/0xbb0 ksys_write+0x17e/0x200 do_syscall_64+0xbb/0xfd0 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7fa5627cbc5e Code: 4d 89 d8 e8 14 bd 00 00 4c 8b 5d f8 41 8b 93 08 03 00 00 59 5e 48 83 f8 fc 74 11 c9 c3 0f 1f 80 00 00 00 00 48 8b 45 10 0f 05 <c9> c3 83 e2 39 83 fa 08 75 e7 e8 13 ff ff ff 0f 1f 00 f3 0f 1e fa RSP: 002b:00007fff1fe14700 EFLAGS: 00000202 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fa5627cbc5e RDX: 0000000000001f9c RSI: 00007fff1fe16984 RDI: 0000000000000005 RBP: 00007fff1fe14710 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000202 R12: 00007fff1fe16920 R13: 0000000000002000 R14: 0000000000001f9c R15: 0000000000001f9c The packet scheduler could attempt a reinjection after receiving an MP_FAIL and before the infinite map has been transmitted, causing a deadlock since MPTCP needs to do the reinjection atomically from WRT fallback. Address the issue explicitly avoiding the reinjection in the critical scenario. Note that this is the only fallback critical section that could potentially send packets and hit the double-lock.

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: fix the crash issue for zero copy XDP_TX action There is a crash issue when running zero copy XDP_TX action, the crash log is shown below. [ 216.122464] Unable to handle kernel paging request at virtual address fffeffff80000000 [ 216.187524] Internal error: Oops: 0000000096000144 [#1] SMP [ 216.301694] Call trace: [ 216.304130] dcache_clean_poc+0x20/0x38 (P) [ 216.308308] __dma_sync_single_for_device+0x1bc/0x1e0 [ 216.313351] stmmac_xdp_xmit_xdpf+0x354/0x400 [ 216.317701] __stmmac_xdp_run_prog+0x164/0x368 [ 216.322139] stmmac_napi_poll_rxtx+0xba8/0xf00 [ 216.326576] __napi_poll+0x40/0x218 [ 216.408054] Kernel panic - not syncing: Oops: Fatal exception in interrupt For XDP_TX action, the xdp_buff is converted to xdp_frame by xdp_convert_buff_to_frame(). The memory type of the resulting xdp_frame depends on the memory type of the xdp_buff. For page pool based xdp_buff it produces xdp_frame with memory type MEM_TYPE_PAGE_POOL. For zero copy XSK pool based xdp_buff it produces xdp_frame with memory type MEM_TYPE_PAGE_ORDER0. However, stmmac_xdp_xmit_back() does not check the memory type and always uses the page pool type, this leads to invalid mappings and causes the crash. Therefore, check the xdp_buff memory type in stmmac_xdp_xmit_back() to fix this issue.

In the Linux kernel, the following vulnerability has been resolved: iavf: fix off-by-one issues in iavf_config_rss_reg() There are off-by-one bugs when configuring RSS hash key and lookup table, causing out-of-bounds reads to memory [1] and out-of-bounds writes to device registers. Before commit 43a3d9ba34c9 ("i40evf: Allow PF driver to configure RSS"), the loop upper bounds were: i <= I40E_VFQF_{HKEY,HLUT}_MAX_INDEX which is safe since the value is the last valid index. That commit changed the bounds to: i <= adapter->rss_{key,lut}_size / 4 where `rss_{key,lut}_size / 4` is the number of dwords, so the last valid index is `(rss_{key,lut}_size / 4) - 1`. Therefore, using `<=` accesses one element past the end. Fix the issues by using `<` instead of `<=`, ensuring we do not exceed the bounds. [1] KASAN splat about rss_key_size off-by-one BUG: KASAN: slab-out-of-bounds in iavf_config_rss+0x619/0x800 Read of size 4 at addr ffff888102c50134 by task kworker/u8:6/63 CPU: 0 UID: 0 PID: 63 Comm: kworker/u8:6 Not tainted 6.18.0-rc2-enjuk-tnguy-00378-g3005f5b77652-dirty #156 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Workqueue: iavf iavf_watchdog_task Call Trace: <TASK> dump_stack_lvl+0x6f/0xb0 print_report+0x170/0x4f3 kasan_report+0xe1/0x1a0 iavf_config_rss+0x619/0x800 iavf_watchdog_task+0x2be7/0x3230 process_one_work+0x7fd/0x1420 worker_thread+0x4d1/0xd40 kthread+0x344/0x660 ret_from_fork+0x249/0x320 ret_from_fork_asm+0x1a/0x30 </TASK> Allocated by task 63: kasan_save_stack+0x30/0x50 kasan_save_track+0x14/0x30 __kasan_kmalloc+0x7f/0x90 __kmalloc_noprof+0x246/0x6f0 iavf_watchdog_task+0x28fc/0x3230 process_one_work+0x7fd/0x1420 worker_thread+0x4d1/0xd40 kthread+0x344/0x660 ret_from_fork+0x249/0x320 ret_from_fork_asm+0x1a/0x30 The buggy address belongs to the object at ffff888102c50100 which belongs to the cache kmalloc-64 of size 64 The buggy address is located 0 bytes to the right of allocated 52-byte region [ffff888102c50100, ffff888102c50134) The buggy address belongs to the physical page: page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x102c50 flags: 0x200000000000000(node=0|zone=2) page_type: f5(slab) raw: 0200000000000000 ffff8881000418c0 dead000000000122 0000000000000000 raw: 0000000000000000 0000000080200020 00000000f5000000 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888102c50000: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc ffff888102c50080: 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc fc >ffff888102c50100: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc ^ ffff888102c50180: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc ffff888102c50200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc

In the Linux kernel, the following vulnerability has been resolved: ipv6: fix a BUG in rt6_get_pcpu_route() under PREEMPT_RT On PREEMPT_RT kernels, after rt6_get_pcpu_route() returns NULL, the current task can be preempted. Another task running on the same CPU may then execute rt6_make_pcpu_route() and successfully install a pcpu_rt entry. When the first task resumes execution, its cmpxchg() in rt6_make_pcpu_route() will fail because rt6i_pcpu is no longer NULL, triggering the BUG_ON(prev). It's easy to reproduce it by adding mdelay() after rt6_get_pcpu_route(). Using preempt_disable/enable is not appropriate here because ip6_rt_pcpu_alloc() may sleep. Fix this by handling the cmpxchg() failure gracefully on PREEMPT_RT: free our allocation and return the existing pcpu_rt installed by another task. The BUG_ON is replaced by WARN_ON_ONCE for non-PREEMPT_RT kernels where such races should not occur.

In the Linux kernel, the following vulnerability has been resolved: smack: /smack/doi: accept previously used values Writing to /smack/doi a value that has ever been written there in the past disables networking for non-ambient labels. E.g. # cat /smack/doi 3 # netlabelctl -p cipso list Configured CIPSO mappings (1) DOI value : 3 mapping type : PASS_THROUGH # netlabelctl -p map list Configured NetLabel domain mappings (3) domain: "_" (IPv4) protocol: UNLABELED domain: DEFAULT (IPv4) protocol: CIPSO, DOI = 3 domain: DEFAULT (IPv6) protocol: UNLABELED # cat /smack/ambient _ # cat /proc/$$/attr/smack/current _ # ping -c1 10.1.95.12 64 bytes from 10.1.95.12: icmp_seq=1 ttl=64 time=0.964 ms # echo foo >/proc/$$/attr/smack/current # ping -c1 10.1.95.12 64 bytes from 10.1.95.12: icmp_seq=1 ttl=64 time=0.956 ms unknown option 86 # echo 4 >/smack/doi # echo 3 >/smack/doi !> [ 214.050395] smk_cipso_doi:691 cipso add rc = -17 # echo 3 >/smack/doi !> [ 249.402261] smk_cipso_doi:678 remove rc = -2 !> [ 249.402261] smk_cipso_doi:691 cipso add rc = -17 # ping -c1 10.1.95.12 !!> ping: 10.1.95.12: Address family for hostname not supported # echo _ >/proc/$$/attr/smack/current # ping -c1 10.1.95.12 64 bytes from 10.1.95.12: icmp_seq=1 ttl=64 time=0.617 ms This happens because Smack keeps decommissioned DOIs, fails to re-add them, and consequently refuses to add the “default” domain map: # netlabelctl -p cipso list Configured CIPSO mappings (2) DOI value : 3 mapping type : PASS_THROUGH DOI value : 4 mapping type : PASS_THROUGH # netlabelctl -p map list Configured NetLabel domain mappings (2) domain: "_" (IPv4) protocol: UNLABELED !> (no ipv4 map for default domain here) domain: DEFAULT (IPv6) protocol: UNLABELED Fix by clearing decommissioned DOI definitions and serializing concurrent DOI updates with a new lock. Also: - allow /smack/doi to live unconfigured, since adding a map (netlbl_cfg_cipsov4_map_add) may fail. CIPSO_V4_DOI_UNKNOWN(0) indicates the unconfigured DOI - add new DOI before removing the old default map, so the old map remains if the add fails (2008-02-04, Casey Schaufler)

In the Linux kernel, the following vulnerability has been resolved: wifi: rtw88: Fix alignment fault in rtw_core_enable_beacon() rtw_core_enable_beacon() reads 4 bytes from an address that is not a multiple of 4. This results in a crash on some systems. Do 1 byte reads/writes instead. Unable to handle kernel paging request at virtual address ffff8000827e0522 Mem abort info: ESR = 0x0000000096000021 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x21: alignment fault Data abort info: ISV = 0, ISS = 0x00000021, ISS2 = 0x00000000 CM = 0, WnR = 0, TnD = 0, TagAccess = 0 GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0 swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000005492000 [ffff8000827e0522] pgd=0000000000000000, p4d=10000001021d9403, pud=10000001021da403, pmd=100000011061c403, pte=00780000f3200f13 Internal error: Oops: 0000000096000021 [#1] SMP Modules linked in: [...] rtw88_8822ce rtw88_8822c rtw88_pci rtw88_core [...] CPU: 0 UID: 0 PID: 73 Comm: kworker/u32:2 Tainted: G W 6.17.9 #1-NixOS VOLUNTARY Tainted: [W]=WARN Hardware name: FriendlyElec NanoPC-T6 LTS (DT) Workqueue: phy0 rtw_c2h_work [rtw88_core] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : rtw_pci_read32+0x18/0x40 [rtw88_pci] lr : rtw_core_enable_beacon+0xe0/0x148 [rtw88_core] sp : ffff800080cc3ca0 x29: ffff800080cc3ca0 x28: ffff0001031fc240 x27: ffff000102100828 x26: ffffd2cb7c9b4088 x25: ffff0001031fc2c0 x24: ffff000112fdef00 x23: ffff000112fdef18 x22: ffff000111c29970 x21: 0000000000000001 x20: 0000000000000001 x19: ffff000111c22040 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : ffffd2cb6507c090 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 x2 : 0000000000007f10 x1 : 0000000000000522 x0 : ffff8000827e0522 Call trace: rtw_pci_read32+0x18/0x40 [rtw88_pci] (P) rtw_hw_scan_chan_switch+0x124/0x1a8 [rtw88_core] rtw_fw_c2h_cmd_handle+0x254/0x290 [rtw88_core] rtw_c2h_work+0x50/0x98 [rtw88_core] process_one_work+0x178/0x3f8 worker_thread+0x208/0x418 kthread+0x120/0x220 ret_from_fork+0x10/0x20 Code: d28fe202 8b020000 f9524400 8b214000 (b9400000) ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: wifi: brcmfmac: pcie: handle randbuf allocation failure The kzalloc() in brcmf_pcie_download_fw_nvram() will return null if the physical memory has run out. As a result, if we use get_random_bytes() to generate random bytes in the randbuf, the null pointer dereference bug will happen. In order to prevent allocation failure, this patch adds a separate function using buffer on kernel stack to generate random bytes in the randbuf, which could prevent the kernel stack from overflow.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: lpc18xx-dmamux: fix device leak on route allocation Make sure to drop the reference taken when looking up the DMA mux platform device during route allocation. Note that holding a reference to a device does not prevent its driver data from going away so there is no point in keeping the reference.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix deadlock on SRQ async events. xa_lock for SRQ table may be required in AEQ. Use xa_store_irq()/ xa_erase_irq() to avoid deadlock.

In the Linux kernel, the following vulnerability has been resolved: shmem: fix recovery on rename failures maple_tree insertions can fail if we are seriously short on memory; simple_offset_rename() does not recover well if it runs into that. The same goes for simple_offset_rename_exchange(). Moreover, shmem_whiteout() expects that if it succeeds, the caller will progress to d_move(), i.e. that shmem_rename2() won't fail past the successful call of shmem_whiteout(). Not hard to fix, fortunately - mtree_store() can't fail if the index we are trying to store into is already present in the tree as a singleton. For simple_offset_rename_exchange() that's enough - we just need to be careful about the order of operations. For simple_offset_rename() solution is to preinsert the target into the tree for new_dir; the rest can be done without any potentially failing operations. That preinsertion has to be done in shmem_rename2() rather than in simple_offset_rename() itself - otherwise we'd need to deal with the possibility of failure after successful shmem_whiteout().

In the Linux kernel, the following vulnerability has been resolved: drm/mediatek: Init `ddp_comp` with devm_kcalloc() In the case where `conn_routes` is true we allocate an extra slot in the `ddp_comp` array but mtk_drm_crtc_create() never seemed to initialize it in the test case I ran. For me, this caused a later crash when we looped through the array in mtk_drm_crtc_mode_valid(). This showed up for me when I booted with `slub_debug=FZPUA` which poisons the memory initially. Without `slub_debug` I couldn't reproduce, presumably because the later code handles the value being NULL and in most cases (not guaranteed in all cases) the memory the allocator returned started out as 0. It really doesn't hurt to initialize the array with devm_kcalloc() since the array is small and the overhead of initting a handful of elements to 0 is small. In general initting memory to zero is a safer practice and usually it's suggested to only use the non-initting alloc functions if you really need to. Let's switch the function to use an allocation function that zeros the memory. For me, this avoids the crash.