Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV110W, RV130, RV130W, and RV215W Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. The vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device. Cisco has not released software updates that address these vulnerabilities.

Multiple exploitable buffer overflow vulnerabilities exist in the PubNub message handler for the "cc" channel of Insteon Hub running firmware version 1012. Specially crafted commands sent through the PubNub service can cause a stack-based buffer overflow overwriting arbitrary data. An attacker should send an authenticated HTTP request to trigger this vulnerability. In cmd g_b, at 0x9d015714, the value for the `grp` key is copied using `strcpy` to the buffer at `$sp+0x280`.This buffer is 16 bytes large, sending anything longer will cause a buffer overflow.

An issue was discovered in Xen through 4.9.x. Grant copying code made an implication that any grant pin would be accompanied by a suitable page reference. Other portions of code, however, did not match up with that assumption. When such a grant copy operation is being done on a grant of a dying domain, the assumption turns out wrong. A malicious guest administrator can cause hypervisor memory corruption, most likely resulting in host crash and a Denial of Service. Privilege escalation and information leaks cannot be ruled out.

A vulnerability was found in Netgear EX6200 1.0.3.94. It has been classified as critical. This affects the function sub_54014. The manipulation of the argument host leads to buffer overflow. It is possible to initiate the attack remotely. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Netgear EX6200 1.0.3.94. It has been declared as critical. This vulnerability affects the function sub_54340. The manipulation of the argument host leads to buffer overflow. The attack can be initiated remotely. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Netgear JWNR2000v2 1.0.0.11. It has been classified as critical. Affected is the function sub_4238E8. The manipulation of the argument host leads to buffer overflow. It is possible to launch the attack remotely. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability, which was classified as critical, was found in Netgear EX6200 1.0.3.94. Affected is the function sub_41940. The manipulation of the argument host leads to buffer overflow. It is possible to launch the attack remotely. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability, which was classified as critical, was found in Tenda W9 1.0.0.7(4456). This affects the function setWrlBasicInfo of the component httpd. The manipulation of the argument ssidIndex leads to stack-based buffer overflow. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-250707. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

On Insteon Hub 2245-222 devices with firmware version 1012, specially crafted replies received from the PubNub service can cause buffer overflows on a global section overwriting arbitrary data. An attacker should impersonate PubNub and answer an HTTPS GET request to trigger this vulnerability. A strcpy overflows the buffer insteon_pubnub.channel_ak, which has a size of 16 bytes. An attacker can send an arbitrarily long "ak" parameter in order to exploit this vulnerability.

On Insteon Hub 2245-222 devices with firmware version 1012, specially crafted replies received from the PubNub service can cause buffer overflows on a global section overwriting arbitrary data. An attacker should impersonate PubNub and answer an HTTPS GET request to trigger this vulnerability. A strcpy overflows the buffer insteon_pubnub.channel_ad_r, which has a size of 16 bytes. An attacker can send an arbitrarily long "ad_r" parameter in order to exploit this vulnerability.

A vulnerability was found in Tenda W12 and i24 3.0.0.4(2887)/3.0.0.5(3644) and classified as critical. Affected by this issue is the function cgiSysUplinkCheckSet of the file /bin/httpd. The manipulation of the argument hostIp1/hostIp2 leads to stack-based buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

Multiple stack-based buffer overflows in TP-Link WR940N WiFi routers with hardware version 4 allow remote authenticated users to execute arbitrary code via the (1) ping_addr parameter to PingIframeRpm.htm or (2) dnsserver2 parameter to WanStaticIpV6CfgRpm.htm.

A vulnerability was found in Tenda W12 and i24 3.0.0.4(2887)/3.0.0.5(3644). It has been rated as critical. This issue affects the function cgiSysScheduleRebootSet of the file /bin/httpd. The manipulation of the argument rebootDate leads to stack-based buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in Tenda W9 1.0.0.7(4456). It has been declared as critical. Affected by this vulnerability is the function formAddSysLogRule of the component httpd. The manipulation of the argument sysRulenEn leads to stack-based buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-250711. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been found in D-Link DWR-M961 1.1.36 and classified as critical. This vulnerability affects unknown code of the file /boafrm/formStaticDHCP of the component Authorization Interface. The manipulation of the argument Hostname leads to stack-based buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. Upgrading to version 1.1.49 is able to address this issue. It is recommended to upgrade the affected component.

A vulnerability was found in Tenda AC15 up to 15.03.05.19 and classified as critical. This issue affects the function fromSetWirelessRepeat of the file /goform/WifiExtraSet. The manipulation of the argument mac leads to buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in Tenda W12 and i24 3.0.0.4(2887)/3.0.0.5(3644). It has been declared as critical. This vulnerability affects the function cgiPingSet of the file /bin/httpd. The manipulation of the argument pingIP leads to stack-based buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability, which was classified as critical, was found in D-Link DIR-600L up to 2.07B01. This affects the function formLogin. The manipulation of the argument host leads to buffer overflow. It is possible to initiate the attack remotely. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was found in Tenda W12 3.0.0.5. It has been rated as critical. Affected by this issue is the function cgiWifiRadioSet of the file /bin/httpd. The manipulation leads to stack-based buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

Stack buffer overflow in httpd in Asuswrt-Merlin firmware 380.67_0RT-AC5300 and earlier for ASUS devices and ASUS firmware for ASUS RT-AC5300, RT_AC1900P, RT-AC68U, RT-AC68P, RT-AC88U, RT-AC66U, RT-AC66U_B1, RT-AC58U, RT-AC56U, RT-AC55U, RT-AC52U, RT-AC51U, RT-N18U, RT-N66U, RT-N56U, RT-AC3200, RT-AC3100, RT_AC1200GU, RT_AC1200G, RT-AC1200, RT-AC53, RT-N12HP, RT-N12HP_B1, RT-N12D1, RT-N12+, RT_N12+_PRO, RT-N16, and RT-N300 devices allows remote attackers to execute arbitrary code on the router by sending a crafted http GET request packet that includes a long delete_offline_client parameter in the url.

A buffer copy without checking size of input vulnerability has been reported to affect several QNAP operating system versions. If exploited, the vulnerability could allow authenticated users to execute code via a network. We have already fixed the vulnerability in the following versions: QTS 5.1.6.2722 build 20240402 and later QuTS hero h5.1.6.2734 build 20240414 and later

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `band` parameter at offset `0x0045aad8` of the `httpd_portal` binary shipped with v5.1.0 Build 20220926 of the EAP225.

IBM Engineering Systems Design Rhapsody 9.0.2, 10.0, and 10.0.1 is vulnerable to a stack-based buffer overflow, caused by improper bounds checking. A local user could overflow the buffer and execute arbitrary code on the system.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `ssid` parameter at offset `0x0045ab7c` of the `httpd_portal` binary shipped with v5.1.0 Build 20220926 of the EAP225.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `profile` parameter at offset `0x0045abc8` of the `httpd_portal` binary shipped with v5.1.0 Build 20220926 of the EAP225.

A vulnerability, which was classified as critical, has been found in Tenda RX3 16.03.13.11. This issue affects the function formSetDeviceName of the file /goform/SetOnlineDevName. The manipulation of the argument devName leads to stack-based buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used.

A vulnerability was found in Tenda AC1206 15.03.06.23. It has been classified as critical. Affected is the function form_fast_setting_wifi_set of the file /goform/fast_setting_wifi_set. The manipulation of the argument ssid/timeZone leads to buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. Other parameters might be affected as well.

IBM Engineering Systems Design Rhapsody 9.0.2, 10.0, and 10.0.1 is vulnerable to a stack-based buffer overflow, caused by improper bounds checking. A local user could overflow the buffer and execute arbitrary code on the system.

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `profile` parameter at offset `0x4224b0` of the `httpd` binary shipped with v5.0.4 Build 20220216 of the EAP115.

A vulnerability was found in Tenda AC7 15.03.06.44. It has been rated as critical. Affected by this issue is the function formSetPPTPServer of the file /goform/SetPptpServerCfg. The manipulation of the argument pptp_server_start_ip/pptp_server_end_ip leads to buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used.

A flaw was found in the ptp4l program of the linuxptp package. A missing length check when forwarding a PTP message between ports allows a remote attacker to cause an information leak, crash, or potentially remote code execution. The highest threat from this vulnerability is to data confidentiality and integrity as well as system availability. This flaw affects linuxptp versions before 3.1.1, before 2.0.1, before 1.9.3, before 1.8.1, before 1.7.1, before 1.6.1 and before 1.5.1.

A vulnerability was found in Tenda AC10 16.03.10.13 and classified as critical. This issue affects the function ShutdownSetAdd of the file /goform/ShutdownSetAdd. The manipulation of the argument list leads to stack-based buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used.

A buffer copy without checking size of input vulnerability has been reported to affect several QNAP operating system versions. If exploited, the vulnerability could allow authenticated users to execute code via a network. We have already fixed the vulnerability in the following versions: QTS 5.1.6.2722 build 20240402 and later QuTS hero h5.1.6.2734 build 20240414 and later

A stack-based buffer overflow vulnerability exists in the web interface Radio Scheduling functionality of Tp-Link AC1350 Wireless MU-MIMO Gigabit Access Point (EAP225 V3) v5.1.0 Build 20220926. A specially crafted series of HTTP requests can lead to remote code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.This vulnerability refers specifically to the overflow that occurs via the `action` parameter at offset `0x422448` of the `httpd` binary shipped with v5.0.4 Build 20220216 of the EAP115.

A stack-based buffer overflow vulnerability exists in the JSON Parsing getblockschedule() functionality of Netgear RAX30 1.0.11.96 and 1.0.7.78. A specially crafted HTTP request can lead to code execution. An attacker can make an authenticated HTTP request to trigger this vulnerability.

A vulnerability was found in D-Link DIR-605L 2.13B01. It has been classified as critical. This affects the function formSetWAN_Wizard534. The manipulation of the argument curTime leads to buffer overflow. It is possible to initiate the attack remotely. The vendor was contacted early about this disclosure. This vulnerability only affects products that are no longer supported by the maintainer.

A heap buffer overflow flaw was found in QEMU's Cirrus CLGD 54xx VGA emulator's VNC display driver support before 2.9; the issue could occur when a VNC client attempted to update its display after a VGA operation is performed by a guest. A privileged user/process inside a guest could use this flaw to crash the QEMU process or, potentially, execute arbitrary code on the host with privileges of the QEMU process.

Buffer overflow in I-O DATA DEVICE TS-WRLP firmware version 1.01.02 and earlier and TS-WRLA firmware version 1.01.02 and earlier allows an attacker with administrator rights to cause a denial-of-service (DoS) or execute arbitrary code via unspecified vectors.

IBM General Parallel File System is vulnerable to a buffer overflow. A remote authenticated attacker could overflow a buffer and execute arbitrary code on the system with root privileges or cause the server to crash.

Stack-based buffer overflow in cgi-bin/cgi_main in NUUO NVRmini 2 1.7.6 through 3.0.0 and NETGEAR ReadyNAS Surveillance 1.1.2 allows remote authenticated users to execute arbitrary code via the sn parameter to the transfer_license command.

Stack-based buffer overflow in the Administration Server in IBM HTTP Server 6.1.0.x through 6.1.0.47, 7.0.0.x before 7.0.0.39, 8.0.0.x before 8.0.0.12, and 8.5.x before 8.5.5.7, as used in WebSphere Application Server and other products, allows remote authenticated users to execute arbitrary code via unspecified vectors.

A vulnerability was found in Tenda M3 1.0.0.13(4903). Affected by this issue is the function formSetVlanPolicy of the file /goform/setVlanPolicyData. Performing a manipulation of the argument qvlan_truck_port results in heap-based buffer overflow. Remote exploitation of the attack is possible. The exploit has been made public and could be used.

A flaw has been found in UTT 进取 520W 1.7.7-180627. This vulnerability affects the function strcpy of the file /goform/formTaskEdit. Executing a manipulation of the argument selDateType can lead to buffer overflow. The attack can be executed remotely. The exploit has been published and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A security flaw has been discovered in Tenda AC23 16.03.07.52. Affected is the function formSetPPTPUserList of the component HTTP POST Request Handler. Performing a manipulation of the argument list results in buffer overflow. The attack can be initiated remotely.

A vulnerability classified as critical was found in D-Link DAP-1320 1.00. Affected by this vulnerability is the function set_ws_action of the file /dws/api/. The manipulation leads to heap-based buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. This vulnerability only affects products that are no longer supported by the maintainer.

A vulnerability was identified in D-Link DWR-M920 up to 1.1.50. This issue affects the function sub_464794 of the file /boafrm/formDefRoute. The manipulation of the argument submit-url leads to buffer overflow. The attack may be initiated remotely. The exploit is publicly available and might be used.

The fix_hostname function in cURL and libcurl 7.37.0 through 7.41.0 does not properly calculate an index, which allows remote attackers to cause a denial of service (out-of-bounds read or write and crash) or possibly have other unspecified impact via a zero-length host name, as demonstrated by "http://:80" and ":80."

A vulnerability has been found in Tenda AC20 up to 16.03.08.12. The impacted element is the function sscanf of the file /goform/PowerSaveSet. The manipulation of the argument powerSavingEn/time/powerSaveDelay/ledCloseType leads to buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used.