In the Linux kernel, the following vulnerability has been resolved: jffs2: prevent xattr node from overflowing the eraseblock Add a check to make sure that the requested xattr node size is no larger than the eraseblock minus the cleanmarker. Unlike the usual inode nodes, the xattr nodes aren't split into parts and spread across multiple eraseblocks, which means that a xattr node must not occupy more than one eraseblock. If the requested xattr value is too large, the xattr node can spill onto the next eraseblock, overwriting the nodes and causing errors such as: jffs2: argh. node added in wrong place at 0x0000b050(2) jffs2: nextblock 0x0000a000, expected at 0000b00c jffs2: error: (823) do_verify_xattr_datum: node CRC failed at 0x01e050, read=0xfc892c93, calc=0x000000 jffs2: notice: (823) jffs2_get_inode_nodes: Node header CRC failed at 0x01e00c. {848f,2fc4,0fef511f,59a3d171} jffs2: Node at 0x0000000c with length 0x00001044 would run over the end of the erase block jffs2: Perhaps the file system was created with the wrong erase size? jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000010: 0x1044 instead This breaks the filesystem and can lead to KASAN crashes such as: BUG: KASAN: slab-out-of-bounds in jffs2_sum_add_kvec+0x125e/0x15d0 Read of size 4 at addr ffff88802c31e914 by task repro/830 CPU: 0 PID: 830 Comm: repro Not tainted 6.9.0-rc3+ #1 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0xc6/0x120 print_report+0xc4/0x620 ? __virt_addr_valid+0x308/0x5b0 kasan_report+0xc1/0xf0 ? jffs2_sum_add_kvec+0x125e/0x15d0 ? jffs2_sum_add_kvec+0x125e/0x15d0 jffs2_sum_add_kvec+0x125e/0x15d0 jffs2_flash_direct_writev+0xa8/0xd0 jffs2_flash_writev+0x9c9/0xef0 ? __x64_sys_setxattr+0xc4/0x160 ? do_syscall_64+0x69/0x140 ? entry_SYSCALL_64_after_hwframe+0x76/0x7e [...] Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: soundwire: cadence: fix invalid PDI offset For some reason, we add an offset to the PDI, presumably to skip the PDI0 and PDI1 which are reserved for BPT. This code is however completely wrong and leads to an out-of-bounds access. We were just lucky so far since we used only a couple of PDIs and remained within the PDI array bounds. A Fixes: tag is not provided since there are no known platforms where the out-of-bounds would be accessed, and the initial code had problems as well. A follow-up patch completely removes this useless offset.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat/qat_4xxx - fix off by one in uof_get_name() The fw_objs[] array has "num_objs" elements so the > needs to be >= to prevent an out of bounds read.

In the Linux kernel, the following vulnerability has been resolved: iavf: Fix out-of-bounds when setting channels on remove If we set channels greater during iavf_remove(), and waiting reset done would be timeout, then returned with error but changed num_active_queues directly, that will lead to OOB like the following logs. Because the num_active_queues is greater than tx/rx_rings[] allocated actually. Reproducer: [root@host ~]# cat repro.sh #!/bin/bash pf_dbsf="0000:41:00.0" vf0_dbsf="0000:41:02.0" g_pids=() function do_set_numvf() { echo 2 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) echo 0 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) } function do_set_channel() { local nic=$(ls -1 --indicator-style=none /sys/bus/pci/devices/${vf0_dbsf}/net/) [ -z "$nic" ] && { sleep $((RANDOM%3)) ; return 1; } ifconfig $nic 192.168.18.5 netmask 255.255.255.0 ifconfig $nic up ethtool -L $nic combined 1 ethtool -L $nic combined 4 sleep $((RANDOM%3)) } function on_exit() { local pid for pid in "${g_pids[@]}"; do kill -0 "$pid" &>/dev/null && kill "$pid" &>/dev/null done g_pids=() } trap "on_exit; exit" EXIT while :; do do_set_numvf ; done & g_pids+=($!) while :; do do_set_channel ; done & g_pids+=($!) wait Result: [ 3506.152887] iavf 0000:41:02.0: Removing device [ 3510.400799] ================================================================== [ 3510.400820] BUG: KASAN: slab-out-of-bounds in iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400823] Read of size 8 at addr ffff88b6f9311008 by task repro.sh/55536 [ 3510.400823] [ 3510.400830] CPU: 101 PID: 55536 Comm: repro.sh Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1 [ 3510.400832] Hardware name: Powerleader PR2008AL/H12DSi-N6, BIOS 2.0 04/09/2021 [ 3510.400835] Call Trace: [ 3510.400851] dump_stack+0x71/0xab [ 3510.400860] print_address_description+0x6b/0x290 [ 3510.400865] ? iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400868] kasan_report+0x14a/0x2b0 [ 3510.400873] iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400880] iavf_remove+0x2b6/0xc70 [iavf] [ 3510.400884] ? iavf_free_all_rx_resources+0x160/0x160 [iavf] [ 3510.400891] ? wait_woken+0x1d0/0x1d0 [ 3510.400895] ? notifier_call_chain+0xc1/0x130 [ 3510.400903] pci_device_remove+0xa8/0x1f0 [ 3510.400910] device_release_driver_internal+0x1c6/0x460 [ 3510.400916] pci_stop_bus_device+0x101/0x150 [ 3510.400919] pci_stop_and_remove_bus_device+0xe/0x20 [ 3510.400924] pci_iov_remove_virtfn+0x187/0x420 [ 3510.400927] ? pci_iov_add_virtfn+0xe10/0xe10 [ 3510.400929] ? pci_get_subsys+0x90/0x90 [ 3510.400932] sriov_disable+0xed/0x3e0 [ 3510.400936] ? bus_find_device+0x12d/0x1a0 [ 3510.400953] i40e_free_vfs+0x754/0x1210 [i40e] [ 3510.400966] ? i40e_reset_all_vfs+0x880/0x880 [i40e] [ 3510.400968] ? pci_get_device+0x7c/0x90 [ 3510.400970] ? pci_get_subsys+0x90/0x90 [ 3510.400982] ? pci_vfs_assigned.part.7+0x144/0x210 [ 3510.400987] ? __mutex_lock_slowpath+0x10/0x10 [ 3510.400996] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e] [ 3510.401001] sriov_numvfs_store+0x214/0x290 [ 3510.401005] ? sriov_totalvfs_show+0x30/0x30 [ 3510.401007] ? __mutex_lock_slowpath+0x10/0x10 [ 3510.401011] ? __check_object_size+0x15a/0x350 [ 3510.401018] kernfs_fop_write+0x280/0x3f0 [ 3510.401022] vfs_write+0x145/0x440 [ 3510.401025] ksys_write+0xab/0x160 [ 3510.401028] ? __ia32_sys_read+0xb0/0xb0 [ 3510.401031] ? fput_many+0x1a/0x120 [ 3510.401032] ? filp_close+0xf0/0x130 [ 3510.401038] do_syscall_64+0xa0/0x370 [ 3510.401041] ? page_fault+0x8/0x30 [ 3510.401043] entry_SYSCALL_64_after_hwframe+0x65/0xca [ 3510.401073] RIP: 0033:0x7f3a9bb842c0 [ 3510.401079] Code: 73 01 c3 48 8b 0d d8 cb 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 89 24 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d ---truncated---

In the Linux kernel, the following vulnerability has been resolved: igb: Fix potential invalid memory access in igb_init_module() The pci_register_driver() can fail and when this happened, the dca_notifier needs to be unregistered, otherwise the dca_notifier can be called when igb fails to install, resulting to invalid memory access.

In the Linux kernel, the following vulnerability has been resolved: md/raid10: check slab-out-of-bounds in md_bitmap_get_counter If we write a large number to md/bitmap_set_bits, md_bitmap_checkpage() will return -EINVAL because 'page >= bitmap->pages', but the return value was not checked immediately in md_bitmap_get_counter() in order to set *blocks value and slab-out-of-bounds occurs. Move check of 'page >= bitmap->pages' to md_bitmap_get_counter() and return directly if true.

In the Linux kernel, the following vulnerability has been resolved: blk-iocost: avoid out of bounds shift UBSAN catches undefined behavior in blk-iocost, where sometimes iocg->delay is shifted right by a number that is too large, resulting in undefined behavior on some architectures. [ 186.556576] ------------[ cut here ]------------ UBSAN: shift-out-of-bounds in block/blk-iocost.c:1366:23 shift exponent 64 is too large for 64-bit type 'u64' (aka 'unsigned long long') CPU: 16 PID: 0 Comm: swapper/16 Tainted: G S E N 6.9.0-0_fbk700_debug_rc2_kbuilder_0_gc85af715cac0 #1 Hardware name: Quanta Twin Lakes MP/Twin Lakes Passive MP, BIOS F09_3A23 12/08/2020 Call Trace: <IRQ> dump_stack_lvl+0x8f/0xe0 __ubsan_handle_shift_out_of_bounds+0x22c/0x280 iocg_kick_delay+0x30b/0x310 ioc_timer_fn+0x2fb/0x1f80 __run_timer_base+0x1b6/0x250 ... Avoid that undefined behavior by simply taking the "delay = 0" branch if the shift is too large. I am not sure what the symptoms of an undefined value delay will be, but I suspect it could be more than a little annoying to debug.

In the Linux kernel, the following vulnerability has been resolved: net: fix out-of-bounds access in ops_init net_alloc_generic is called by net_alloc, which is called without any locking. It reads max_gen_ptrs, which is changed under pernet_ops_rwsem. It is read twice, first to allocate an array, then to set s.len, which is later used to limit the bounds of the array access. It is possible that the array is allocated and another thread is registering a new pernet ops, increments max_gen_ptrs, which is then used to set s.len with a larger than allocated length for the variable array. Fix it by reading max_gen_ptrs only once in net_alloc_generic. If max_gen_ptrs is later incremented, it will be caught in net_assign_generic.

In the Linux kernel, the following vulnerability has been resolved: ice: ensure the copied buf is NUL terminated Currently, we allocate a count-sized kernel buffer and copy count bytes from userspace to that buffer. Later, we use sscanf on this buffer but we don't ensure that the string is terminated inside the buffer, this can lead to OOB read when using sscanf. Fix this issue by using memdup_user_nul instead of memdup_user.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - validate slices count returned by FW The function adf_send_admin_tl_start() enables the telemetry (TL) feature on a QAT device by sending the ICP_QAT_FW_TL_START message to the firmware. This triggers the FW to start writing TL data to a DMA buffer in memory and returns an array containing the number of accelerators of each type (slices) supported by this HW. The pointer to this array is stored in the adf_tl_hw_data data structure called slice_cnt. The array slice_cnt is then used in the function tl_print_dev_data() to report in debugfs only statistics about the supported accelerators. An incorrect value of the elements in slice_cnt might lead to an out of bounds memory read. At the moment, there isn't an implementation of FW that returns a wrong value, but for robustness validate the slice count array returned by FW.

In the Linux kernel, the following vulnerability has been resolved: drm/vmwgfx: Fix invalid reads in fence signaled events Correctly set the length of the drm_event to the size of the structure that's actually used. The length of the drm_event was set to the parent structure instead of to the drm_vmw_event_fence which is supposed to be read. drm_read uses the length parameter to copy the event to the user space thus resuling in oob reads.

In the Linux kernel, the following vulnerability has been resolved: s390/cio: Ensure the copied buf is NUL terminated Currently, we allocate a lbuf-sized kernel buffer and copy lbuf from userspace to that buffer. Later, we use scanf on this buffer but we don't ensure that the string is terminated inside the buffer, this can lead to OOB read when using scanf. Fix this issue by using memdup_user_nul instead.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: check A-MSDU format more carefully If it looks like there's another subframe in the A-MSDU but the header isn't fully there, we can end up reading data out of bounds, only to discard later. Make this a bit more careful and check if the subframe header can even be present.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix out of bounds reads when finding clock sources The current USB-audio driver code doesn't check bLength of each descriptor at traversing for clock descriptors. That is, when a device provides a bogus descriptor with a shorter bLength, the driver might hit out-of-bounds reads. For addressing it, this patch adds sanity checks to the validator functions for the clock descriptor traversal. When the descriptor length is shorter than expected, it's skipped in the loop. For the clock source and clock multiplier descriptors, we can just check bLength against the sizeof() of each descriptor type. OTOH, the clock selector descriptor of UAC2 and UAC3 has an array of bNrInPins elements and two more fields at its tail, hence those have to be checked in addition to the sizeof() check.

In the Linux kernel, the following vulnerability has been resolved: dma-mapping: benchmark: fix node id validation While validating node ids in map_benchmark_ioctl(), node_possible() may be provided with invalid argument outside of [0,MAX_NUMNODES-1] range leading to: BUG: KASAN: wild-memory-access in map_benchmark_ioctl (kernel/dma/map_benchmark.c:214) Read of size 8 at addr 1fffffff8ccb6398 by task dma_map_benchma/971 CPU: 7 PID: 971 Comm: dma_map_benchma Not tainted 6.9.0-rc6 #37 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:117) kasan_report (mm/kasan/report.c:603) kasan_check_range (mm/kasan/generic.c:189) variable_test_bit (arch/x86/include/asm/bitops.h:227) [inline] arch_test_bit (arch/x86/include/asm/bitops.h:239) [inline] _test_bit at (include/asm-generic/bitops/instrumented-non-atomic.h:142) [inline] node_state (include/linux/nodemask.h:423) [inline] map_benchmark_ioctl (kernel/dma/map_benchmark.c:214) full_proxy_unlocked_ioctl (fs/debugfs/file.c:333) __x64_sys_ioctl (fs/ioctl.c:890) do_syscall_64 (arch/x86/entry/common.c:83) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130) Compare node ids with sane bounds first. NUMA_NO_NODE is considered a special valid case meaning that benchmarking kthreads won't be bound to a cpuset of a given node. Found by Linux Verification Center (linuxtesting.org).

In the Linux kernel, the following vulnerability has been resolved: thermal: intel: powerclamp: fix mismatch in get function for max_idle KASAN reported this [ 444.853098] BUG: KASAN: global-out-of-bounds in param_get_int+0x77/0x90 [ 444.853111] Read of size 4 at addr ffffffffc16c9220 by task cat/2105 ... [ 444.853442] The buggy address belongs to the variable: [ 444.853443] max_idle+0x0/0xffffffffffffcde0 [intel_powerclamp] There is a mismatch between the param_get_int and the definition of max_idle. Replacing param_get_int with param_get_byte resolves this issue.

In the Linux kernel, the following vulnerability has been resolved: jfs: jfs_dmap: Validate db_l2nbperpage while mounting In jfs_dmap.c at line 381, BLKTODMAP is used to get a logical block number inside dbFree(). db_l2nbperpage, which is the log2 number of blocks per page, is passed as an argument to BLKTODMAP which uses it for shifting. Syzbot reported a shift out-of-bounds crash because db_l2nbperpage is too big. This happens because the large value is set without any validation in dbMount() at line 181. Thus, make sure that db_l2nbperpage is correct while mounting. Max number of blocks per page = Page size / Min block size => log2(Max num_block per page) = log2(Page size / Min block size) = log2(Page size) - log2(Min block size) => Max db_l2nbperpage = L2PSIZE - L2MINBLOCKSIZE

In the Linux kernel, the following vulnerability has been resolved: ext4: fix out-of-bound read in ext4_xattr_inode_dec_ref_all() There's issue as follows: BUG: KASAN: use-after-free in ext4_xattr_inode_dec_ref_all+0x6ff/0x790 Read of size 4 at addr ffff88807b003000 by task syz-executor.0/15172 CPU: 3 PID: 15172 Comm: syz-executor.0 Call Trace: __dump_stack lib/dump_stack.c:82 [inline] dump_stack+0xbe/0xfd lib/dump_stack.c:123 print_address_description.constprop.0+0x1e/0x280 mm/kasan/report.c:400 __kasan_report.cold+0x6c/0x84 mm/kasan/report.c:560 kasan_report+0x3a/0x50 mm/kasan/report.c:585 ext4_xattr_inode_dec_ref_all+0x6ff/0x790 fs/ext4/xattr.c:1137 ext4_xattr_delete_inode+0x4c7/0xda0 fs/ext4/xattr.c:2896 ext4_evict_inode+0xb3b/0x1670 fs/ext4/inode.c:323 evict+0x39f/0x880 fs/inode.c:622 iput_final fs/inode.c:1746 [inline] iput fs/inode.c:1772 [inline] iput+0x525/0x6c0 fs/inode.c:1758 ext4_orphan_cleanup fs/ext4/super.c:3298 [inline] ext4_fill_super+0x8c57/0xba40 fs/ext4/super.c:5300 mount_bdev+0x355/0x410 fs/super.c:1446 legacy_get_tree+0xfe/0x220 fs/fs_context.c:611 vfs_get_tree+0x8d/0x2f0 fs/super.c:1576 do_new_mount fs/namespace.c:2983 [inline] path_mount+0x119a/0x1ad0 fs/namespace.c:3316 do_mount+0xfc/0x110 fs/namespace.c:3329 __do_sys_mount fs/namespace.c:3540 [inline] __se_sys_mount+0x219/0x2e0 fs/namespace.c:3514 do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46 entry_SYSCALL_64_after_hwframe+0x67/0xd1 Memory state around the buggy address: ffff88807b002f00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88807b002f80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff88807b003000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ^ ffff88807b003080: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff88807b003100: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Above issue happens as ext4_xattr_delete_inode() isn't check xattr is valid if xattr is in inode. To solve above issue call xattr_check_inode() check if xattr if valid in inode. In fact, we can directly verify in ext4_iget_extra_inode(), so that there is no divergent verification.

In the Linux kernel, the following vulnerability has been resolved: usbnet: ipheth: fix possible overflow in DPE length check Originally, it was possible for the DPE length check to overflow if wDatagramIndex + wDatagramLength > U16_MAX. This could lead to an OoB read. Move the wDatagramIndex term to the other side of the inequality. An existing condition ensures that wDatagramIndex < urb->actual_length.

In the Linux kernel, the following vulnerability has been resolved: Squashfs: check the inode number is not the invalid value of zero Syskiller has produced an out of bounds access in fill_meta_index(). That out of bounds access is ultimately caused because the inode has an inode number with the invalid value of zero, which was not checked. The reason this causes the out of bounds access is due to following sequence of events: 1. Fill_meta_index() is called to allocate (via empty_meta_index()) and fill a metadata index. It however suffers a data read error and aborts, invalidating the newly returned empty metadata index. It does this by setting the inode number of the index to zero, which means unused (zero is not a valid inode number). 2. When fill_meta_index() is subsequently called again on another read operation, locate_meta_index() returns the previous index because it matches the inode number of 0. Because this index has been returned it is expected to have been filled, and because it hasn't been, an out of bounds access is performed. This patch adds a sanity check which checks that the inode number is not zero when the inode is created and returns -EINVAL if it is. [phillip@squashfs.org.uk: whitespace fix]

In the Linux kernel, the following vulnerability has been resolved: usbnet: ipheth: fix DPE OoB read Fix an out-of-bounds DPE read, limit the number of processed DPEs to the amount that fits into the fixed-size NDP16 header.

In the Linux kernel, the following vulnerability has been resolved: tunnels: fix out of bounds access when building IPv6 PMTU error If the ICMPv6 error is built from a non-linear skb we get the following splat, BUG: KASAN: slab-out-of-bounds in do_csum+0x220/0x240 Read of size 4 at addr ffff88811d402c80 by task netperf/820 CPU: 0 PID: 820 Comm: netperf Not tainted 6.8.0-rc1+ #543 ... kasan_report+0xd8/0x110 do_csum+0x220/0x240 csum_partial+0xc/0x20 skb_tunnel_check_pmtu+0xeb9/0x3280 vxlan_xmit_one+0x14c2/0x4080 vxlan_xmit+0xf61/0x5c00 dev_hard_start_xmit+0xfb/0x510 __dev_queue_xmit+0x7cd/0x32a0 br_dev_queue_push_xmit+0x39d/0x6a0 Use skb_checksum instead of csum_partial who cannot deal with non-linear SKBs.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: validate mech token in session setup If client send invalid mech token in session setup request, ksmbd validate and make the error if it is invalid.

In the Linux kernel, the following vulnerability has been resolved: btrfs: dev-replace: properly validate device names There's a syzbot report that device name buffers passed to device replace are not properly checked for string termination which could lead to a read out of bounds in getname_kernel(). Add a helper that validates both source and target device name buffers. For devid as the source initialize the buffer to empty string in case something tries to read it later. This was originally analyzed and fixed in a different way by Edward Adam Davis (see links).

In the Linux kernel, the following vulnerability has been resolved: i2c: i801: Fix block process call transactions According to the Intel datasheets, software must reset the block buffer index twice for block process call transactions: once before writing the outgoing data to the buffer, and once again before reading the incoming data from the buffer. The driver is currently missing the second reset, causing the wrong portion of the block buffer to be read.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix slab-out-of-bounds in smb_strndup_from_utf16() If ->NameOffset of smb2_create_req is smaller than Buffer offset of smb2_create_req, slab-out-of-bounds read can happen from smb2_open. This patch set the minimum value of the name offset to the buffer offset to validate name length of smb2_create_req().

In the Linux kernel, the following vulnerability has been resolved: net: qualcomm: rmnet: fix global oob in rmnet_policy The variable rmnet_link_ops assign a *bigger* maxtype which leads to a global out-of-bounds read when parsing the netlink attributes. See bug trace below: ================================================================== BUG: KASAN: global-out-of-bounds in validate_nla lib/nlattr.c:386 [inline] BUG: KASAN: global-out-of-bounds in __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600 Read of size 1 at addr ffffffff92c438d0 by task syz-executor.6/84207 CPU: 0 PID: 84207 Comm: syz-executor.6 Tainted: G N 6.1.0 #3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x8b/0xb3 lib/dump_stack.c:106 print_address_description mm/kasan/report.c:284 [inline] print_report+0x172/0x475 mm/kasan/report.c:395 kasan_report+0xbb/0x1c0 mm/kasan/report.c:495 validate_nla lib/nlattr.c:386 [inline] __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600 __nla_parse+0x3e/0x50 lib/nlattr.c:697 nla_parse_nested_deprecated include/net/netlink.h:1248 [inline] __rtnl_newlink+0x50a/0x1880 net/core/rtnetlink.c:3485 rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3594 rtnetlink_rcv_msg+0x43c/0xd70 net/core/rtnetlink.c:6091 netlink_rcv_skb+0x14f/0x410 net/netlink/af_netlink.c:2540 netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline] netlink_unicast+0x54e/0x800 net/netlink/af_netlink.c:1345 netlink_sendmsg+0x930/0xe50 net/netlink/af_netlink.c:1921 sock_sendmsg_nosec net/socket.c:714 [inline] sock_sendmsg+0x154/0x190 net/socket.c:734 ____sys_sendmsg+0x6df/0x840 net/socket.c:2482 ___sys_sendmsg+0x110/0x1b0 net/socket.c:2536 __sys_sendmsg+0xf3/0x1c0 net/socket.c:2565 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7fdcf2072359 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 f1 19 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fdcf13e3168 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007fdcf219ff80 RCX: 00007fdcf2072359 RDX: 0000000000000000 RSI: 0000000020000200 RDI: 0000000000000003 RBP: 00007fdcf20bd493 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007fffbb8d7bdf R14: 00007fdcf13e3300 R15: 0000000000022000 </TASK> The buggy address belongs to the variable: rmnet_policy+0x30/0xe0 The buggy address belongs to the physical page: page:0000000065bdeb3c refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x155243 flags: 0x200000000001000(reserved|node=0|zone=2) raw: 0200000000001000 ffffea00055490c8 ffffea00055490c8 0000000000000000 raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffffffff92c43780: f9 f9 f9 f9 00 00 00 02 f9 f9 f9 f9 00 00 00 07 ffffffff92c43800: f9 f9 f9 f9 00 00 00 05 f9 f9 f9 f9 06 f9 f9 f9 >ffffffff92c43880: f9 f9 f9 f9 00 00 00 00 00 00 f9 f9 f9 f9 f9 f9 ^ ffffffff92c43900: 00 00 00 00 00 00 00 00 07 f9 f9 f9 f9 f9 f9 f9 ffffffff92c43980: 00 00 00 07 f9 f9 f9 f9 00 00 00 05 f9 f9 f9 f9 According to the comment of `nla_parse_nested_deprecated`, the maxtype should be len(destination array) - 1. Hence use `IFLA_RMNET_MAX` here.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix mmhub client id out-of-bounds access Properly handle cid 0x140.

In the Linux kernel, the following vulnerability has been resolved: bpf: add check for invalid name in btf_name_valid_section() If the length of the name string is 1 and the value of name[0] is NULL byte, an OOB vulnerability occurs in btf_name_valid_section() and the return value is true, so the invalid name passes the check. To solve this, you need to check if the first position is NULL byte and if the first character is printable.

In the Linux kernel, the following vulnerability has been resolved: ath9k_htc: fix potential out of bounds access with invalid rxstatus->rs_keyix The "rxstatus->rs_keyix" eventually gets passed to test_bit() so we need to ensure that it is within the bitmap. drivers/net/wireless/ath/ath9k/common.c:46 ath9k_cmn_rx_accept() error: passing untrusted data 'rx_stats->rs_keyix' to 'test_bit()'

In the Linux kernel, the following vulnerability has been resolved: tracing: Limit access to parser->buffer when trace_get_user failed When the length of the string written to set_ftrace_filter exceeds FTRACE_BUFF_MAX, the following KASAN alarm will be triggered: BUG: KASAN: slab-out-of-bounds in strsep+0x18c/0x1b0 Read of size 1 at addr ffff0000d00bd5ba by task ash/165 CPU: 1 UID: 0 PID: 165 Comm: ash Not tainted 6.16.0-g6bcdbd62bd56-dirty Hardware name: linux,dummy-virt (DT) Call trace: show_stack+0x34/0x50 (C) dump_stack_lvl+0xa0/0x158 print_address_description.constprop.0+0x88/0x398 print_report+0xb0/0x280 kasan_report+0xa4/0xf0 __asan_report_load1_noabort+0x20/0x30 strsep+0x18c/0x1b0 ftrace_process_regex.isra.0+0x100/0x2d8 ftrace_regex_release+0x484/0x618 __fput+0x364/0xa58 ____fput+0x28/0x40 task_work_run+0x154/0x278 do_notify_resume+0x1f0/0x220 el0_svc+0xec/0xf0 el0t_64_sync_handler+0xa0/0xe8 el0t_64_sync+0x1ac/0x1b0 The reason is that trace_get_user will fail when processing a string longer than FTRACE_BUFF_MAX, but not set the end of parser->buffer to 0. Then an OOB access will be triggered in ftrace_regex_release-> ftrace_process_regex->strsep->strpbrk. We can solve this problem by limiting access to parser->buffer when trace_get_user failed.

In the Linux kernel, the following vulnerability has been resolved: comedi: das16m1: Fix bit shift out of bounds When checking for a supported IRQ number, the following test is used: /* only irqs 2, 3, 4, 5, 6, 7, 10, 11, 12, 14, and 15 are valid */ if ((1 << it->options[1]) & 0xdcfc) { However, `it->options[i]` is an unchecked `int` value from userspace, so the shift amount could be negative or out of bounds. Fix the test by requiring `it->options[1]` to be within bounds before proceeding with the original test.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: csum: Fix OoB access in IP checksum code for negative lengths Commit 69e3a6aa6be2 ("LoongArch: Add checksum optimization for 64-bit system") would cause an undefined shift and an out-of-bounds read. Commit 8bd795fedb84 ("arm64: csum: Fix OoB access in IP checksum code for negative lengths") fixes the same issue on ARM64.

In the Linux kernel, the following vulnerability has been resolved: binder: fix OOB in binder_add_freeze_work() In binder_add_freeze_work() we iterate over the proc->nodes with the proc->inner_lock held. However, this lock is temporarily dropped to acquire the node->lock first (lock nesting order). This can race with binder_deferred_release() which removes the nodes from the proc->nodes rbtree and adds them into binder_dead_nodes list. This leads to a broken iteration in binder_add_freeze_work() as rb_next() will use data from binder_dead_nodes, triggering an out-of-bounds access: ================================================================== BUG: KASAN: global-out-of-bounds in rb_next+0xfc/0x124 Read of size 8 at addr ffffcb84285f7170 by task freeze/660 CPU: 8 UID: 0 PID: 660 Comm: freeze Not tainted 6.11.0-07343-ga727812a8d45 #18 Hardware name: linux,dummy-virt (DT) Call trace: rb_next+0xfc/0x124 binder_add_freeze_work+0x344/0x534 binder_ioctl+0x1e70/0x25ac __arm64_sys_ioctl+0x124/0x190 The buggy address belongs to the variable: binder_dead_nodes+0x10/0x40 [...] ================================================================== This is possible because proc->nodes (rbtree) and binder_dead_nodes (list) share entries in binder_node through a union: struct binder_node { [...] union { struct rb_node rb_node; struct hlist_node dead_node; }; Fix the race by checking that the proc is still alive. If not, simply break out of the iteration.

In the Linux kernel, the following vulnerability has been resolved: scsi: bfa: Ensure the copied buf is NUL terminated Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from userspace to that buffer. Later, we use sscanf on this buffer but we don't ensure that the string is terminated inside the buffer, this can lead to OOB read when using sscanf. Fix this issue by using memdup_user_nul instead of memdup_user.

In the Linux kernel, the following vulnerability has been resolved: net: qrtr: fix OOB Read in qrtr_endpoint_post Syzbot reported slab-out-of-bounds Read in qrtr_endpoint_post. The problem was in wrong _size_ type: if (len != ALIGN(size, 4) + hdrlen) goto err; If size from qrtr_hdr is 4294967293 (0xfffffffd), the result of ALIGN(size, 4) will be 0. In case of len == hdrlen and size == 4294967293 in header this check won't fail and skb_put_data(skb, data + hdrlen, size); will read out of bound from data, which is hdrlen allocated block.

In the Linux kernel, the following vulnerability has been resolved: netfilter: conntrack: dccp: copy entire header to stack buffer, not just basic one Eric Dumazet says: nf_conntrack_dccp_packet() has an unique: dh = skb_header_pointer(skb, dataoff, sizeof(_dh), &_dh); And nothing more is 'pulled' from the packet, depending on the content. dh->dccph_doff, and/or dh->dccph_x ...) So dccp_ack_seq() is happily reading stuff past the _dh buffer. BUG: KASAN: stack-out-of-bounds in nf_conntrack_dccp_packet+0x1134/0x11c0 Read of size 4 at addr ffff000128f66e0c by task syz-executor.2/29371 [..] Fix this by increasing the stack buffer to also include room for the extra sequence numbers and all the known dccp packet type headers, then pull again after the initial validation of the basic header. While at it, mark packets invalid that lack 48bit sequence bit but where RFC says the type MUST use them. Compile tested only. v2: first skb_header_pointer() now needs to adjust the size to only pull the generic header. (Eric) Heads-up: I intend to remove dccp conntrack support later this year.

In the Linux kernel, the following vulnerability has been resolved: drm/i915/sseu: fix max_subslices array-index-out-of-bounds access It seems that commit bc3c5e0809ae ("drm/i915/sseu: Don't try to store EU mask internally in UAPI format") exposed a potential out-of-bounds access, reported by UBSAN as following on a laptop with a gen 11 i915 card: UBSAN: array-index-out-of-bounds in drivers/gpu/drm/i915/gt/intel_sseu.c:65:27 index 6 is out of range for type 'u16 [6]' CPU: 2 PID: 165 Comm: systemd-udevd Not tainted 6.2.0-9-generic #9-Ubuntu Hardware name: Dell Inc. XPS 13 9300/077Y9N, BIOS 1.11.0 03/22/2022 Call Trace: <TASK> show_stack+0x4e/0x61 dump_stack_lvl+0x4a/0x6f dump_stack+0x10/0x18 ubsan_epilogue+0x9/0x3a __ubsan_handle_out_of_bounds.cold+0x42/0x47 gen11_compute_sseu_info+0x121/0x130 [i915] intel_sseu_info_init+0x15d/0x2b0 [i915] intel_gt_init_mmio+0x23/0x40 [i915] i915_driver_mmio_probe+0x129/0x400 [i915] ? intel_gt_probe_all+0x91/0x2e0 [i915] i915_driver_probe+0xe1/0x3f0 [i915] ? drm_privacy_screen_get+0x16d/0x190 [drm] ? acpi_dev_found+0x64/0x80 i915_pci_probe+0xac/0x1b0 [i915] ... According to the definition of sseu_dev_info, eu_mask->hsw is limited to a maximum of GEN_MAX_SS_PER_HSW_SLICE (6) sub-slices, but gen11_sseu_info_init() can potentially set 8 sub-slices, in the !IS_JSL_EHL(gt->i915) case. Fix this by reserving up to 8 slots for max_subslices in the eu_mask struct. (cherry picked from commit 3cba09a6ac86ea1d456909626eb2685596c07822)

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid out-of-boundary access in dnode page As Jiaming Zhang reported: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x1c1/0x2a0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x17e/0x800 mm/kasan/report.c:480 kasan_report+0x147/0x180 mm/kasan/report.c:593 data_blkaddr fs/f2fs/f2fs.h:3053 [inline] f2fs_data_blkaddr fs/f2fs/f2fs.h:3058 [inline] f2fs_get_dnode_of_data+0x1a09/0x1c40 fs/f2fs/node.c:855 f2fs_reserve_block+0x53/0x310 fs/f2fs/data.c:1195 prepare_write_begin fs/f2fs/data.c:3395 [inline] f2fs_write_begin+0xf39/0x2190 fs/f2fs/data.c:3594 generic_perform_write+0x2c7/0x910 mm/filemap.c:4112 f2fs_buffered_write_iter fs/f2fs/file.c:4988 [inline] f2fs_file_write_iter+0x1ec8/0x2410 fs/f2fs/file.c:5216 new_sync_write fs/read_write.c:593 [inline] vfs_write+0x546/0xa90 fs/read_write.c:686 ksys_write+0x149/0x250 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xf3/0x3d0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f The root cause is in the corrupted image, there is a dnode has the same node id w/ its inode, so during f2fs_get_dnode_of_data(), it tries to access block address in dnode at offset 934, however it parses the dnode as inode node, so that get_dnode_addr() returns 360, then it tries to access page address from 360 + 934 * 4 = 4096 w/ 4 bytes. To fix this issue, let's add sanity check for node id of all direct nodes during f2fs_get_dnode_of_data().

In the Linux kernel, the following vulnerability has been resolved: nfc: llcp: fix nfc_llcp_setsockopt() unsafe copies syzbot reported unsafe calls to copy_from_sockptr() [1] Use copy_safe_from_sockptr() instead. [1] BUG: KASAN: slab-out-of-bounds in copy_from_sockptr_offset include/linux/sockptr.h:49 [inline] BUG: KASAN: slab-out-of-bounds in copy_from_sockptr include/linux/sockptr.h:55 [inline] BUG: KASAN: slab-out-of-bounds in nfc_llcp_setsockopt+0x6c2/0x850 net/nfc/llcp_sock.c:255 Read of size 4 at addr ffff88801caa1ec3 by task syz-executor459/5078 CPU: 0 PID: 5078 Comm: syz-executor459 Not tainted 6.8.0-syzkaller-08951-gfe46a7dd189e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114 print_address_description mm/kasan/report.c:377 [inline] print_report+0x169/0x550 mm/kasan/report.c:488 kasan_report+0x143/0x180 mm/kasan/report.c:601 copy_from_sockptr_offset include/linux/sockptr.h:49 [inline] copy_from_sockptr include/linux/sockptr.h:55 [inline] nfc_llcp_setsockopt+0x6c2/0x850 net/nfc/llcp_sock.c:255 do_sock_setsockopt+0x3b1/0x720 net/socket.c:2311 __sys_setsockopt+0x1ae/0x250 net/socket.c:2334 __do_sys_setsockopt net/socket.c:2343 [inline] __se_sys_setsockopt net/socket.c:2340 [inline] __x64_sys_setsockopt+0xb5/0xd0 net/socket.c:2340 do_syscall_64+0xfd/0x240 entry_SYSCALL_64_after_hwframe+0x6d/0x75 RIP: 0033:0x7f7fac07fd89 Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 91 18 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007fff660eb788 EFLAGS: 00000246 ORIG_RAX: 0000000000000036 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f7fac07fd89 RDX: 0000000000000000 RSI: 0000000000000118 RDI: 0000000000000004 RBP: 0000000000000000 R08: 0000000000000002 R09: 0000000000000000 R10: 0000000020000a80 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000

In the Linux kernel, the following vulnerability has been resolved: mm/memory-failure: fix VM_BUG_ON_PAGE(PagePoisoned(page)) when unpoison memory When I did memory failure tests, below panic occurs: page dumped because: VM_BUG_ON_PAGE(PagePoisoned(page)) kernel BUG at include/linux/page-flags.h:616! Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 PID: 720 Comm: bash Not tainted 6.10.0-rc1-00195-g148743902568 #40 RIP: 0010:unpoison_memory+0x2f3/0x590 RSP: 0018:ffffa57fc8787d60 EFLAGS: 00000246 RAX: 0000000000000037 RBX: 0000000000000009 RCX: ffff9be25fcdc9c8 RDX: 0000000000000000 RSI: 0000000000000027 RDI: ffff9be25fcdc9c0 RBP: 0000000000300000 R08: ffffffffb4956f88 R09: 0000000000009ffb R10: 0000000000000284 R11: ffffffffb4926fa0 R12: ffffe6b00c000000 R13: ffff9bdb453dfd00 R14: 0000000000000000 R15: fffffffffffffffe FS: 00007f08f04e4740(0000) GS:ffff9be25fcc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000564787a30410 CR3: 000000010d4e2000 CR4: 00000000000006f0 Call Trace: <TASK> unpoison_memory+0x2f3/0x590 simple_attr_write_xsigned.constprop.0.isra.0+0xb3/0x110 debugfs_attr_write+0x42/0x60 full_proxy_write+0x5b/0x80 vfs_write+0xd5/0x540 ksys_write+0x64/0xe0 do_syscall_64+0xb9/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f08f0314887 RSP: 002b:00007ffece710078 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000009 RCX: 00007f08f0314887 RDX: 0000000000000009 RSI: 0000564787a30410 RDI: 0000000000000001 RBP: 0000564787a30410 R08: 000000000000fefe R09: 000000007fffffff R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000009 R13: 00007f08f041b780 R14: 00007f08f0417600 R15: 00007f08f0416a00 </TASK> Modules linked in: hwpoison_inject ---[ end trace 0000000000000000 ]--- RIP: 0010:unpoison_memory+0x2f3/0x590 RSP: 0018:ffffa57fc8787d60 EFLAGS: 00000246 RAX: 0000000000000037 RBX: 0000000000000009 RCX: ffff9be25fcdc9c8 RDX: 0000000000000000 RSI: 0000000000000027 RDI: ffff9be25fcdc9c0 RBP: 0000000000300000 R08: ffffffffb4956f88 R09: 0000000000009ffb R10: 0000000000000284 R11: ffffffffb4926fa0 R12: ffffe6b00c000000 R13: ffff9bdb453dfd00 R14: 0000000000000000 R15: fffffffffffffffe FS: 00007f08f04e4740(0000) GS:ffff9be25fcc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000564787a30410 CR3: 000000010d4e2000 CR4: 00000000000006f0 Kernel panic - not syncing: Fatal exception Kernel Offset: 0x31c00000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff) ---[ end Kernel panic - not syncing: Fatal exception ]--- The root cause is that unpoison_memory() tries to check the PG_HWPoison flags of an uninitialized page. So VM_BUG_ON_PAGE(PagePoisoned(page)) is triggered. This can be reproduced by below steps: 1.Offline memory block: echo offline > /sys/devices/system/memory/memory12/state 2.Get offlined memory pfn: page-types -b n -rlN 3.Write pfn to unpoison-pfn echo <pfn> > /sys/kernel/debug/hwpoison/unpoison-pfn This scenario can be identified by pfn_to_online_page() returning NULL. And ZONE_DEVICE pages are never expected, so we can simply fail if pfn_to_online_page() == NULL to fix the bug.

In the Linux kernel, the following vulnerability has been resolved: tty: Fix out-of-bound vmalloc access in imageblit This issue happens when a userspace program does an ioctl FBIOPUT_VSCREENINFO passing the fb_var_screeninfo struct containing only the fields xres, yres, and bits_per_pixel with values. If this struct is the same as the previous ioctl, the vc_resize() detects it and doesn't call the resize_screen(), leaving the fb_var_screeninfo incomplete. And this leads to the updatescrollmode() calculates a wrong value to fbcon_display->vrows, which makes the real_y() return a wrong value of y, and that value, eventually, causes the imageblit to access an out-of-bound address value. To solve this issue I made the resize_screen() be called even if the screen does not need any resizing, so it will "fix and fill" the fb_var_screeninfo independently.

In the Linux kernel, the following vulnerability has been resolved: ath5k: fix OOB in ath5k_eeprom_read_pcal_info_5111 The bug was found during fuzzing. Stacktrace locates it in ath5k_eeprom_convert_pcal_info_5111. When none of the curve is selected in the loop, idx can go up to AR5K_EEPROM_N_PD_CURVES. The line makes pd out of bound. pd = &chinfo[pier].pd_curves[idx]; There are many OOB writes using pd later in the code. So I added a sanity check for idx. Checks for other loops involving AR5K_EEPROM_N_PD_CURVES are not needed as the loop index is not used outside the loops. The patch is NOT tested with real device. The following is the fuzzing report BUG: KASAN: slab-out-of-bounds in ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] Write of size 1 at addr ffff8880174a4d60 by task modprobe/214 CPU: 0 PID: 214 Comm: modprobe Not tainted 5.6.0 #1 Call Trace: dump_stack+0x76/0xa0 print_address_description.constprop.0+0x16/0x200 ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] __kasan_report.cold+0x37/0x7c ? ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] kasan_report+0xe/0x20 ath5k_eeprom_read_pcal_info_5111+0x126a/0x1390 [ath5k] ? apic_timer_interrupt+0xa/0x20 ? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k] ? ath5k_pci_eeprom_read+0x228/0x3c0 [ath5k] ath5k_eeprom_init+0x2513/0x6290 [ath5k] ? ath5k_eeprom_init_11a_pcal_freq+0xbc0/0xbc0 [ath5k] ? usleep_range+0xb8/0x100 ? apic_timer_interrupt+0xa/0x20 ? ath5k_eeprom_read_pcal_info_2413+0x2f20/0x2f20 [ath5k] ath5k_hw_init+0xb60/0x1970 [ath5k] ath5k_init_ah+0x6fe/0x2530 [ath5k] ? kasprintf+0xa6/0xe0 ? ath5k_stop+0x140/0x140 [ath5k] ? _dev_notice+0xf6/0xf6 ? apic_timer_interrupt+0xa/0x20 ath5k_pci_probe.cold+0x29a/0x3d6 [ath5k] ? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k] ? mutex_lock+0x89/0xd0 ? ath5k_pci_eeprom_read+0x3c0/0x3c0 [ath5k] local_pci_probe+0xd3/0x160 pci_device_probe+0x23f/0x3e0 ? pci_device_remove+0x280/0x280 ? pci_device_remove+0x280/0x280 really_probe+0x209/0x5d0

In the Linux kernel, the following vulnerability has been resolved: vduse: check that offset is within bounds in get_config() This condition checks "len" but it does not check "offset" and that could result in an out of bounds read if "offset > dev->config_size". The problem is that since both variables are unsigned the "dev->config_size - offset" subtraction would result in a very high unsigned value. I think these checks might not be necessary because "len" and "offset" are supposed to already have been validated using the vhost_vdpa_config_validate() function. But I do not know the code perfectly, and I like to be safe.

In the Linux kernel, the following vulnerability has been resolved: net: usb: aqc111: fix error handling of usbnet read calls Syzkaller, courtesy of syzbot, identified an error (see report [1]) in aqc111 driver, caused by incomplete sanitation of usb read calls' results. This problem is quite similar to the one fixed in commit 920a9fa27e78 ("net: asix: add proper error handling of usb read errors"). For instance, usbnet_read_cmd() may read fewer than 'size' bytes, even if the caller expected the full amount, and aqc111_read_cmd() will not check its result properly. As [1] shows, this may lead to MAC address in aqc111_bind() being only partly initialized, triggering KMSAN warnings. Fix the issue by verifying that the number of bytes read is as expected and not less. [1] Partial syzbot report: BUG: KMSAN: uninit-value in is_valid_ether_addr include/linux/etherdevice.h:208 [inline] BUG: KMSAN: uninit-value in usbnet_probe+0x2e57/0x4390 drivers/net/usb/usbnet.c:1830 is_valid_ether_addr include/linux/etherdevice.h:208 [inline] usbnet_probe+0x2e57/0x4390 drivers/net/usb/usbnet.c:1830 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:-1 [inline] really_probe+0x4d1/0xd90 drivers/base/dd.c:658 __driver_probe_device+0x268/0x380 drivers/base/dd.c:800 ... Uninit was stored to memory at: dev_addr_mod+0xb0/0x550 net/core/dev_addr_lists.c:582 __dev_addr_set include/linux/netdevice.h:4874 [inline] eth_hw_addr_set include/linux/etherdevice.h:325 [inline] aqc111_bind+0x35f/0x1150 drivers/net/usb/aqc111.c:717 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 ... Uninit was stored to memory at: ether_addr_copy include/linux/etherdevice.h:305 [inline] aqc111_read_perm_mac drivers/net/usb/aqc111.c:663 [inline] aqc111_bind+0x794/0x1150 drivers/net/usb/aqc111.c:713 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:-1 [inline] ... Local variable buf.i created at: aqc111_read_perm_mac drivers/net/usb/aqc111.c:656 [inline] aqc111_bind+0x221/0x1150 drivers/net/usb/aqc111.c:713 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772

In the Linux kernel, the following vulnerability has been resolved: Input: elantech - fix stack out of bound access in elantech_change_report_id() The array param[] in elantech_change_report_id() must be at least 3 bytes, because elantech_read_reg_params() is calling ps2_command() with PSMOUSE_CMD_GETINFO, that is going to access 3 bytes from param[], but it's defined in the stack as an array of 2 bytes, therefore we have a potential stack out-of-bounds access here, also confirmed by KASAN: [ 6.512374] BUG: KASAN: stack-out-of-bounds in __ps2_command+0x372/0x7e0 [ 6.512397] Read of size 1 at addr ffff8881024d77c2 by task kworker/2:1/118 [ 6.512416] CPU: 2 PID: 118 Comm: kworker/2:1 Not tainted 5.13.0-22-generic #22+arighi20211110 [ 6.512428] Hardware name: LENOVO 20T8000QGE/20T8000QGE, BIOS R1AET32W (1.08 ) 08/14/2020 [ 6.512436] Workqueue: events_long serio_handle_event [ 6.512453] Call Trace: [ 6.512462] show_stack+0x52/0x58 [ 6.512474] dump_stack+0xa1/0xd3 [ 6.512487] print_address_description.constprop.0+0x1d/0x140 [ 6.512502] ? __ps2_command+0x372/0x7e0 [ 6.512516] __kasan_report.cold+0x7d/0x112 [ 6.512527] ? _raw_write_lock_irq+0x20/0xd0 [ 6.512539] ? __ps2_command+0x372/0x7e0 [ 6.512552] kasan_report+0x3c/0x50 [ 6.512564] __asan_load1+0x6a/0x70 [ 6.512575] __ps2_command+0x372/0x7e0 [ 6.512589] ? ps2_drain+0x240/0x240 [ 6.512601] ? dev_printk_emit+0xa2/0xd3 [ 6.512612] ? dev_vprintk_emit+0xc5/0xc5 [ 6.512621] ? __kasan_check_write+0x14/0x20 [ 6.512634] ? mutex_lock+0x8f/0xe0 [ 6.512643] ? __mutex_lock_slowpath+0x20/0x20 [ 6.512655] ps2_command+0x52/0x90 [ 6.512670] elantech_ps2_command+0x4f/0xc0 [psmouse] [ 6.512734] elantech_change_report_id+0x1e6/0x256 [psmouse] [ 6.512799] ? elantech_report_trackpoint.constprop.0.cold+0xd/0xd [psmouse] [ 6.512863] ? ps2_command+0x7f/0x90 [ 6.512877] elantech_query_info.cold+0x6bd/0x9ed [psmouse] [ 6.512943] ? elantech_setup_ps2+0x460/0x460 [psmouse] [ 6.513005] ? psmouse_reset+0x69/0xb0 [psmouse] [ 6.513064] ? psmouse_attr_set_helper+0x2a0/0x2a0 [psmouse] [ 6.513122] ? phys_pmd_init+0x30e/0x521 [ 6.513137] elantech_init+0x8a/0x200 [psmouse] [ 6.513200] ? elantech_init_ps2+0xf0/0xf0 [psmouse] [ 6.513249] ? elantech_query_info+0x440/0x440 [psmouse] [ 6.513296] ? synaptics_send_cmd+0x60/0x60 [psmouse] [ 6.513342] ? elantech_query_info+0x440/0x440 [psmouse] [ 6.513388] ? psmouse_try_protocol+0x11e/0x170 [psmouse] [ 6.513432] psmouse_extensions+0x65d/0x6e0 [psmouse] [ 6.513476] ? psmouse_try_protocol+0x170/0x170 [psmouse] [ 6.513519] ? mutex_unlock+0x22/0x40 [ 6.513526] ? ps2_command+0x7f/0x90 [ 6.513536] ? psmouse_probe+0xa3/0xf0 [psmouse] [ 6.513580] psmouse_switch_protocol+0x27d/0x2e0 [psmouse] [ 6.513624] psmouse_connect+0x272/0x530 [psmouse] [ 6.513669] serio_driver_probe+0x55/0x70 [ 6.513679] really_probe+0x190/0x720 [ 6.513689] driver_probe_device+0x160/0x1f0 [ 6.513697] device_driver_attach+0x119/0x130 [ 6.513705] ? device_driver_attach+0x130/0x130 [ 6.513713] __driver_attach+0xe7/0x1a0 [ 6.513720] ? device_driver_attach+0x130/0x130 [ 6.513728] bus_for_each_dev+0xfb/0x150 [ 6.513738] ? subsys_dev_iter_exit+0x10/0x10 [ 6.513748] ? _raw_write_unlock_bh+0x30/0x30 [ 6.513757] driver_attach+0x2d/0x40 [ 6.513764] serio_handle_event+0x199/0x3d0 [ 6.513775] process_one_work+0x471/0x740 [ 6.513785] worker_thread+0x2d2/0x790 [ 6.513794] ? process_one_work+0x740/0x740 [ 6.513802] kthread+0x1b4/0x1e0 [ 6.513809] ? set_kthread_struct+0x80/0x80 [ 6.513816] ret_from_fork+0x22/0x30 [ 6.513832] The buggy address belongs to the page: [ 6.513838] page:00000000bc35e189 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1024d7 [ 6.513847] flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff) [ 6.513860] raw: 0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ataflop: potential out of bounds in do_format() The function uses "type" as an array index: q = unit[drive].disk[type]->queue; Unfortunately the bounds check on "type" isn't done until later in the function. Fix this by moving the bounds check to the start.

In the Linux kernel, the following vulnerability has been resolved: sch_cake: Fix out of bounds when parsing TCP options and header The TCP option parser in cake qdisc (cake_get_tcpopt and cake_tcph_may_drop) could read one byte out of bounds. When the length is 1, the execution flow gets into the loop, reads one byte of the opcode, and if the opcode is neither TCPOPT_EOL nor TCPOPT_NOP, it reads one more byte, which exceeds the length of 1. This fix is inspired by commit 9609dad263f8 ("ipv4: tcp_input: fix stack out of bounds when parsing TCP options."). v2 changes: Added doff validation in cake_get_tcphdr to avoid parsing garbage as TCP header. Although it wasn't strictly an out-of-bounds access (memory was allocated), garbage values could be read where CAKE expected the TCP header if doff was smaller than 5.

In the Linux kernel, the following vulnerability has been resolved: scsi: scsi_debug: Fix out-of-bound read in resp_readcap16() The following warning was observed running syzkaller: [ 3813.830724] sg_write: data in/out 65466/242 bytes for SCSI command 0x9e-- guessing data in; [ 3813.830724] program syz-executor not setting count and/or reply_len properly [ 3813.836956] ================================================================== [ 3813.839465] BUG: KASAN: stack-out-of-bounds in sg_copy_buffer+0x157/0x1e0 [ 3813.841773] Read of size 4096 at addr ffff8883cf80f540 by task syz-executor/1549 [ 3813.846612] Call Trace: [ 3813.846995] dump_stack+0x108/0x15f [ 3813.847524] print_address_description+0xa5/0x372 [ 3813.848243] kasan_report.cold+0x236/0x2a8 [ 3813.849439] check_memory_region+0x240/0x270 [ 3813.850094] memcpy+0x30/0x80 [ 3813.850553] sg_copy_buffer+0x157/0x1e0 [ 3813.853032] sg_copy_from_buffer+0x13/0x20 [ 3813.853660] fill_from_dev_buffer+0x135/0x370 [ 3813.854329] resp_readcap16+0x1ac/0x280 [ 3813.856917] schedule_resp+0x41f/0x1630 [ 3813.858203] scsi_debug_queuecommand+0xb32/0x17e0 [ 3813.862699] scsi_dispatch_cmd+0x330/0x950 [ 3813.863329] scsi_request_fn+0xd8e/0x1710 [ 3813.863946] __blk_run_queue+0x10b/0x230 [ 3813.864544] blk_execute_rq_nowait+0x1d8/0x400 [ 3813.865220] sg_common_write.isra.0+0xe61/0x2420 [ 3813.871637] sg_write+0x6c8/0xef0 [ 3813.878853] __vfs_write+0xe4/0x800 [ 3813.883487] vfs_write+0x17b/0x530 [ 3813.884008] ksys_write+0x103/0x270 [ 3813.886268] __x64_sys_write+0x77/0xc0 [ 3813.886841] do_syscall_64+0x106/0x360 [ 3813.887415] entry_SYSCALL_64_after_hwframe+0x44/0xa9 This issue can be reproduced with the following syzkaller log: r0 = openat(0xffffffffffffff9c, &(0x7f0000000040)='./file0\x00', 0x26e1, 0x0) r1 = syz_open_procfs(0xffffffffffffffff, &(0x7f0000000000)='fd/3\x00') open_by_handle_at(r1, &(0x7f00000003c0)=ANY=[@ANYRESHEX], 0x602000) r2 = syz_open_dev$sg(&(0x7f0000000000), 0x0, 0x40782) write$binfmt_aout(r2, &(0x7f0000000340)=ANY=[@ANYBLOB="00000000deff000000000000000000000000000000000000000000000000000047f007af9e107a41ec395f1bded7be24277a1501ff6196a83366f4e6362bc0ff2b247f68a972989b094b2da4fb3607fcf611a22dd04310d28c75039d"], 0x126) In resp_readcap16() we get "int alloc_len" value -1104926854, and then pass the huge arr_len to fill_from_dev_buffer(), but arr is only 32 bytes. This leads to OOB in sg_copy_buffer(). To solve this issue, define alloc_len as u32.

In the Linux kernel, the following vulnerability has been resolved: net: validate lwtstate->data before returning from skb_tunnel_info() skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info type without validation. lwtstate->data can have various types such as mpls_iptunnel_encap, etc and these are not compatible. So skb_tunnel_info() should validate before returning that pointer. Splat looks like: BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan] Read of size 2 at addr ffff888106ec2698 by task ping/811 CPU: 1 PID: 811 Comm: ping Not tainted 5.13.0+ #1195 Call Trace: dump_stack_lvl+0x56/0x7b print_address_description.constprop.8.cold.13+0x13/0x2ee ? vxlan_get_route+0x418/0x4b0 [vxlan] ? vxlan_get_route+0x418/0x4b0 [vxlan] kasan_report.cold.14+0x83/0xdf ? vxlan_get_route+0x418/0x4b0 [vxlan] vxlan_get_route+0x418/0x4b0 [vxlan] [ ... ] vxlan_xmit_one+0x148b/0x32b0 [vxlan] [ ... ] vxlan_xmit+0x25c5/0x4780 [vxlan] [ ... ] dev_hard_start_xmit+0x1ae/0x6e0 __dev_queue_xmit+0x1f39/0x31a0 [ ... ] neigh_xmit+0x2f9/0x940 mpls_xmit+0x911/0x1600 [mpls_iptunnel] lwtunnel_xmit+0x18f/0x450 ip_finish_output2+0x867/0x2040 [ ... ]