An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved on ACX 7000 Series allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). When a device has a Layer 3 or an IRB interface configured in a VPLS instance and specific traffic is received, the evo-pfemand processes crashes which causes a service outage for the respective FPC until the system is recovered manually. This issue only affects Junos OS Evolved 22.4R2-S1 and 22.4R2-S2 releases and is fixed in 22.4R3. No other releases are affected.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved on ACX7000 Series allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). On all ACX 7000 Series platforms running Junos OS Evolved, and configured with IRBs, if a Customer Edge device (CE) device is dual homed to two Provider Edge devices (PE) a traffic loop will occur when the CE sends multicast packets. This issue can be triggered by IPv4 and IPv6 traffic. This issue affects Junos OS Evolved:  All versions from 22.2R1-EVO and later versions before 22.4R2-EVO, This issue does not affect Junos OS Evolved versions before 22.1R1-EVO.

A vulnerability in the pfe-chassisd Chassis Manager (CMLC) daemon of Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) to the EX4300 when specific valid broadcast packets create a broadcast storm condition when received on the me0 interface of the EX4300 Series device. A reboot of the device is required to restore service. Continued receipt of these valid broadcast packets will create a sustained Denial of Service (DoS) against the device. Affected releases are Juniper Networks Junos OS: 16.1 versions above and including 16.1R1 prior to 16.1R7-S5; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.

Crafted packets destined to the management interface (fxp0) of an SRX340 or SRX345 services gateway may create a denial of service (DoS) condition due to buffer space exhaustion. This issue only affects the SRX340 and SRX345 services gateways. No other products or platforms are affected by this vulnerability. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D160 on SRX340/SRX345; 17.3 on SRX340/SRX345; 17.4 versions prior to 17.4R2-S3, 17.4R3 on SRX340/SRX345; 18.1 versions prior to 18.1R3-S1 on SRX340/SRX345; 18.2 versions prior to 18.2R2 on SRX340/SRX345; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX340/SRX345. This issue does not affect Junos OS releases prior to 15.1X49 on any platform.

A NULL Pointer Dereference vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). When Layer 2 traffic is sent through a logical interface, MAC learning happens. If during this process, the interface flaps, an Advanced Forwarding Toolkit manager (evo-aftmand-bt) core is observed. This leads to a PFE restart. The crash reoccurs if the same sequence of events happens, which will lead to a sustained DoS condition. This issue affects Juniper Networks Junos OS Evolved 23.2-EVO versions earlier than 23.2R1-S1-EVO, 23.2R2-EVO.

An Improper Neutralization of Equivalent Special Elements vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on PTX Series allows a unauthenticated, adjacent attacker to cause a Denial of Service (DoS). When MPLS packets are meant to be sent to a flexible tunnel interface (FTI) and if the FTI tunnel is down, these will hit the reject NH, due to which the packets get sent to the CPU and cause a host path wedge condition. This will cause the FPC to hang and requires a manual restart to recover. Please note that this issue specifically affects PTX1000, PTX3000, PTX5000 with FPC3, PTX10002-60C, and PTX10008/16 with LC110x. Other PTX Series devices and Line Cards (LC) are not affected. The following log message can be seen when the issue occurs: Cmerror Op Set: Host Loopback: HOST LOOPBACK WEDGE DETECTED IN PATH ID <id> (URI: /fpc/<fpc>/pfe/<pfe>/cm/<cm>/Host_Loopback/<cm>/HOST_LOOPBACK_MAKE_CMERROR_ID[<id>]) This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S8; * 21.1 versions earlier than 21.1R3-S4; * 21.2 versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S3; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R2-S2, 22.1R3; * 22.2 versions earlier than 22.2R2-S1, 22.2R3.

An Improper Handling of Exceptional Conditions vulnerability in Juniper Networks Junos OS and Junos OS Evolved allows an adjacent unauthenticated attacker to cause a Denial of Service (DoS), which causes the l2cpd process to crash by sending a specific TLV. The l2cpd process is responsible for layer 2 control protocols, such as STP, RSTP, MSTP, VSTP, ERP, and LLDP.  The impact of the l2cpd crash is reinitialization of STP protocols (RSTP, MSTP or VSTP), and MVRP and ERP, leading to a Denial of Service.  Continued receipt and processing of this specific TLV will create a sustained Denial of Service (DoS) condition. This issue affects: Junos OS: all versions before 20.4R3-S9, from 21.2 before 21.2R3-S7, from 21.3 before 21.3R3-S5, from 21.4 before 21.4R3-S4, from 22.1 before 22.1R3-S4, from 22.2 before 22.2R3-S2, from 22.3 before 22.3R2-S2, 22.3R3-S1, from 22.4 before 22.4R2-S2, 22.4R3, from 23.2 before 23.2R1-S1, 23.2R2; Junos OS Evolved: all versions before 21.2R3-S7, from 21.3 before 21.3R3-S5-EVO, from 21.4 before 21.4R3-S5-EVO, from 22.1 before 22.1R3-S4-EVO, from 22.2 before 22.2R3-S2-EVO, from 22.3 before 22.3R2-S2-EVO, 22.3R3-S1-EVO, from 22.4 before 22.4R2-S2-EVO, 22.4R3-EVO, from 23.2 before 23.2R1-S1-EVO, 23.2R2-EVO.

An Improper Isolation or Compartmentalization vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on QFX5000 Series and EX Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If a specific malformed LACP packet is received by a QFX5000 Series, or an EX4400, EX4100 or EX4650 Series device, an LACP flap will occur resulting in traffic loss. This issue affects Junos OS on QFX5000 Series, and on EX4400, EX4100 or EX4650 Series: * 20.4 versions from 20.4R3-S4 before 20.4R3-S8, * 21.2 versions from 21.2R3-S2 before 21.2R3-S6, * 21.4 versions from 21.4R2 before 21.4R3-S4, * 22.1 versions from 22.1R2 before 22.1R3-S3, * 22.2 versions before 22.2R3-S1, * 22.3 versions before 22.3R2-S2, 22.3R3, * 22.4 versions before 22.4R2-S1, 22.4R3.

When an MX Series Broadband Remote Access Server (BRAS) is configured as a Broadband Network Gateway (BNG) with DHCPv6 enabled, jdhcpd might crash when receiving a specific crafted DHCP response message on a subscriber interface. The daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue only affects systems configured with DHCPv6 enabled. DHCPv4 is unaffected by this issue. This issue affects Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S5 on MX Series; 16.1 versions prior to 16.1R7-S5 on MX Series; 16.2 versions prior to 16.2R2-S10 on MX Series; 17.1 versions prior to 17.1R3-S1 on MX Series; 17.2 versions prior to 17.2R3-S2 on MX Series; 17.3 versions prior to 17.3R3-S6 on MX Series; 17.4 versions prior to 17.4R2-S5, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S6 on MX Series; 18.2 versions prior to 18.2R2-S4, 18.2R3 on MX Series; 18.2X75 versions prior to 18.2X75-D50 on MX Series; 18.3 versions prior to 18.3R1-S5, 18.3R3 on MX Series; 18.4 versions prior to 18.4R2 on MX Series; 19.1 versions prior to 19.1R1-S2, 19.1R2 on MX Series.

A Missing Release of Memory after Effective Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on MX Series allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS). If an MX Series device receives PTP packets on an MPC3E that doesn't support PTP this causes a memory leak which will result in unpredictable behavior and ultimately in an MPC crash and restart. To monitor for this issue, please use the following FPC vty level commands: show heap shows an increase in "LAN buffer" utilization and show clksync ptp nbr-upd-info shows non-zero "Pending PFEs" counter. This issue affects Juniper Networks Junos OS on MX Series with MPC3E: * All versions earlier than 20.4R3-S3; * 21.1 versions earlier than 21.1R3-S4; * 21.2 versions earlier than 21.2R3; * 21.3 versions earlier than 21.3R2-S1, 21.3R3; * 21.4 versions earlier than 21.4R2; * 22.1 versions earlier than 22.1R2.

A Missing Release of Memory after Effective Lifetime vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause an rpd crash, leading to Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when traffic engineering is enabled for OSPF or ISIS, and a link flaps, a patroot memory leak is observed. This memory leak, over time, will lead to an rpd crash and restart. The memory usage can be monitored using the below command. user@host> show task memory detail | match patroot This issue affects: Juniper Networks Junos OS * All versions earlier than 21.2R3-S3; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S3; * 22.1 versions earlier than 22.1R3; * 22.2 versions earlier than 22.2R3. Juniper Networks Junos OS Evolved * All versions earlier than 21.3R3-S5-EVO; * 21.4 versions earlier than 21.4R3-EVO; * 22.1 versions earlier than 22.1R3-EVO; * 22.2 versions earlier than 22.2R3-EVO.

An Improper Input Validation vulnerability in Juniper Tunnel Driver (jtd) and ICMP module of Juniper Networks Junos OS Evolved allows an unauthenticated attacker within the MPLS administrative domain to send specifically crafted packets to the Routing Engine (RE) to cause a Denial of Service (DoS).  When specifically crafted transit MPLS IPv4 packets are received by the Packet Forwarding Engine (PFE), these packets are internally forwarded to the RE. Continued receipt of these packets may create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS: * All versions before 21.2R3-S8-EVO; * from 21.4-EVO before 21.4R3-S6-EVO; * from 22.2-EVO before 22.2R3-S4-EVO; * from 22.3-EVO before 22.3R3-S3-EVO; * from 22.4-EVO before 22.4R3-EVO; * from 23.2-EVO before 23.2R2-EVO. * from 23.4-EVO before 23.4R1-S1-EVO.

An Exposure of Resource to Wrong Sphere vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on SRX 300 Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). Specific valid link-local traffic is not blocked on ports in STP blocked state but is instead sent to the control plane of the device. This leads to excessive resource consumption and in turn severe impact on all control and management protocols of the device. This issue affects Juniper Networks Junos OS: * 21.2 version 21.2R3-S3 and later versions earlier than 21.2R3-S6; * 22.1 version 22.1R3 and later versions earlier than 22.1R3-S4; * 22.2 version 22.2R2 and later versions earlier than 22.2R3-S2; * 22.3 version 22.3R2 and later versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2. This issue does not affect Juniper Networks Junos OS 21.4R1 and later versions of 21.4.

An Incomplete Cleanup vulnerability in Nonstop active routing (NSR) component of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause memory leak leading to Denial of Service (DoS). On all Junos OS platforms, when NSR is enabled, a BGP flap will cause memory leak. A manual reboot of the system will restore the services. Note: NSR is not supported on the SRX Series and is therefore not affected by this vulnerability. The memory usage can be monitored using the below commands. user@host> show chassis routing-engine no-forwarding user@host> show system memory | no-more This issue affects: Juniper Networks Junos OS * 21.2 versions earlier than 21.2R3-S5; * 21.3 versions earlier than 21.3R3-S4; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S2; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R2-S1, 22.3R3; * 22.4 versions earlier than 22.4R1-S2, 22.4R2. This issue does not affect Junos OS versions earlier than 20.4R3-S7.

An Improper Handling of Exceptional Conditions vulnerability in the broadband edge subscriber management daemon (bbe-smgd) of Juniper Networks Junos OS on MX Series allows an attacker directly connected to the vulnerable system who repeatedly flaps DHCP subscriber sessions to cause a slow memory leak, ultimately leading to a Denial of Service (DoS). Memory can only be recovered by manually restarting bbe-smgd. This issue only occurs if BFD liveness detection for DHCP subscribers is enabled. Systems without BFD liveness detection enabled are not vulnerable to this issue. Indication of the issue can be observed by periodically executing the 'show system processes extensive' command, which will indicate an increase in memory allocation for bbe-smgd. A small amount of memory is leaked every time a DHCP subscriber logs in, which will become visible over time, ultimately leading to memory starvation. user@junos> show system processes extensive | match bbe-smgd 13071 root 24 0 415M 201M select 0 0:41 7.28% bbe-smgd{bbe-smgd} 13071 root 20 0 415M 201M select 1 0:04 0.00% bbe-smgd{bbe-smgd} ... user@junos> show system processes extensive | match bbe-smgd 13071 root 20 0 420M 208M select 0 4:33 0.10% bbe-smgd{bbe-smgd} 13071 root 20 0 420M 208M select 0 0:12 0.00% bbe-smgd{bbe-smgd} ... This issue affects Juniper Networks Junos OS on MX Series: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S2; * 22.4 versions earlier than 22.4R2-S2, 22.4R3; * 23.2 versions earlier than 23.2R1-S1, 23.2R2.

An Improper Check or Handling of Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If an attacker sends a specific MPLS packet, which upon processing, causes an internal loop, that leads to a PFE crash and restart. Continued receipt of these packets leads to a sustained Denial of Service (DoS) condition. Circuit cross-connect (CCC) needs to be configured on the device for it to be affected by this issue. This issue only affects MX Series with MPC10, MPC11, LC9600, and MX304. This issue affects: Juniper Networks Junos OS 21.4 versions from 21.4R3 earlier than 21.4R3-S5; 22.2 versions from 22.2R2 earlier than 22.2R3-S2; 22.3 versions from 22.3R1 earlier than 22.3R2-S2; 22.3 versions from 22.3R3 earlier than 22.3R3-S1 22.4 versions from 22.4R1 earlier than 22.4R2-S2, 22.4R3; 23.2 versions earlier than 23.2R1-S1, 23.2R2.

An Access of Memory Location After End of Buffer vulnerability in the Layer-2 Control Protocols Daemon (l2cpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, when LLDP is enabled on a specific interface, and a malformed LLDP packet is received, l2cpd crashes and restarts. The impact of the l2cpd crash is reinitialization of STP protocols (RSTP, MSTP or VSTP), and MVRP and ERP. Also, if any services depend on LLDP state (like PoE or VoIP device recognition), then these will also be affected. This issue affects: Junos OS: * from 21.4 before 21.4R3-S4,  * from 22.1 before 22.1R3-S4,  * from 22.2 before 22.2R3-S2,  * from 22.3 before 22.3R2-S2, 22.3R3-S1,  * from 22.4 before 22.4R3,  * from 23.2 before 23.2R2. Junos OS Evolved: * from 21.4-EVO before 21.4R3-S5-EVO,  * from 22.1-EVO before 22.1R3-S4-EVO,  * from 22.2-EVO before 22.2R3-S2-EVO,  * from 22.3-EVO before 22.3R2-S2-EVO, 22.3R3-S1-EVO,  * from 22.4-EVO before 22.4R3-EVO,  * from 23.2-EVO before 23.2R2-EVO. This issue does not affect: * Junos OS versions prior to 21.4R1; * Junos OS Evolved versions prior to 21.4R1-EVO.

A Missing Release of Memory after Effective Lifetime vulnerability in the IKE daemon (iked) of Juniper Networks Junos OS on MX Series with SPC3, and SRX Series allows an administratively adjacent attacker which is able to successfully establish IPsec tunnels to cause a Denial of Service (DoS). If specific values for the IPsec parameters local-ip, remote-ip, remote ike-id, and traffic selectors are sent from the peer, a memory leak occurs during every IPsec SA rekey which is carried out with a specific message sequence. This will eventually result in an iked process crash and restart. The iked process memory consumption can be checked using the below command:   user@host> show system processes extensive | grep iked           PID USERNAME   PRI NICE   SIZE   RES   STATE   C TIME WCPU COMMAND           56903 root       31   0     4016M 2543M CPU0   0 2:10 10.50% iked This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S7; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3-S4; * 22.1 versions earlier than 22.1R3-S3; * 22.2 versions earlier than 22.2R3-S2; * 22.3 versions earlier than 22.3R3; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Layer 2 Address Learning Daemon (l2ald) on Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause Denial of Service (DoS). In an EVPN/VXLAN scenario, when a high amount specific Layer 2 packets are processed by the device, it can cause the Routing Protocol Daemon (rpd) to utilize all CPU resources which causes the device to hang. A manual restart of the rpd is required to restore services. This issue affects both IPv4 and IPv6 implementations. This issue affects Junos OS: All versions earlier than 21.4R3-S7; 22.1 versions earlier than 22.1R3-S5; 22.2 versions earlier than 22.2R3-S3; 22.3 versions earlier than 22.3R3-S3; 22.4 versions earlier than 22.4R3-S2; 23.2 versions earlier than 23.2R2; 23.4 versions earlier than 23.4R1-S1. Junos OS Evolved: All versions earlier than 21.4R3-S7-EVO; 22.1-EVO versions earlier than 22.1R3-S5-EVO; 22.2-EVO versions earlier than 22.2R3-S3-EVO; 22.3-EVO versions earlier than 22.3R3-S3-EVO; 22.4-EVO versions earlier than 22.4R3-S2-EVO; 23.2-EVO versions earlier than 23.2R2-EVO; 23.4-EVO versions earlier than 23.4R1-S1-EVO, 23.4R2-EVO.

An Incomplete List of Disallowed Inputs vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on QFX5000 Series and EX4600 Series allows an adjacent unauthenticated attacker which sends a high rate of specific multicast traffic to cause control traffic received from the network to be dropped. This will impact control protocols (including but not limited to routing-protocols) and lead to a Denial of Service (DoS). Continued receipt of this specific multicast traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX5000 and EX4600 Series: All versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.

An Uncontrolled Resource Consumption vulnerability in the ARP daemon (arpd) and Network Discovery Protocol (ndp) process of Juniper Networks Junos OS Evolved allows a malicious attacker on the local network to consume memory resources, ultimately resulting in a Denial of Service (DoS) condition. Link-layer functions such as IPv4 and/or IPv6 address resolution may be impacted, leading to traffic loss. The processes do not recover on their own and must be manually restarted. Changes in memory usage can be monitored using the following shell commands (header shown for clarity): user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 59.0 0.7 *5702564* 247952 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 49.1 1.0 *5813156* 351184 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 Memory usage can be monitored for the ndp process in a similar fashion: user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5614052* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5725164* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje This issue affects Juniper Networks Junos OS Evolved: 19.4 versions prior to 19.4R2-S3-EVO; 20.1 versions prior to 20.1R2-S4-EVO; all versions of 20.2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 19.4R2-EVO.

Improper Handling of Exceptional Conditions in Ethernet interface frame processing of Juniper Networks Junos OS allows an attacker to send specially crafted frames over the local Ethernet segment, causing the interface to go into a down state, resulting in a Denial of Service (DoS) condition. The interface does not recover on its own and the FPC must be reset manually. Continued receipt and processing of these frames will create a sustained Denial of Service (DoS) condition. This issue is platform-specific and affects the following platforms and line cards: * MPC7E/8E/9E and MPC10E on MX240, MX480, MX960, MX2008, MX2010, and MX2020 * MX204, MX10003, MX10008, MX10016 * EX9200, EX9251 * SRX4600 No other products or platforms are affected by this vulnerability. An indication of this issue occurring can be seen in the system log messages, as shown below: user@host> show log messages | match "Failed to complete DFE tuning" fpc4 smic_phy_dfe_tuning_state: et-4/1/6 - Failed to complete DFE tuning (count 3) and interface will be in a permanently down state: user@host> show interfaces et-4/1/6 terse Interface Admin Link Proto Local Remote et-4/1/6 up down et-4/1/6.0 up down aenet --> ae101.0 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S7 on MX Series; 17.1R1 and later versions prior to 17.2R3-S3 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S11, 17.4R3-S1 on MX Series, SRX4600; 18.1 versions prior to 18.1R3-S10 on MX Series, EX9200 Series, SRX4600; 18.2 versions prior to 18.2R3-S3 on MX Series, EX9200 Series, SRX4600; 18.3 versions prior to 18.3R3-S1 on MX Series, EX9200 Series, SRX4600; 18.4 versions prior to 18.4R2-S3, 18.4R3 on MX Series, EX9200 Series, SRX4600; 19.1 versions prior to 19.1R2-S1, 19.1R3 on MX Series, EX9200 Series, SRX4600; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series, EX9200 Series, SRX4600; 19.3 versions prior to 19.3R2 on MX Series, EX9200 Series, SRX4600. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.

A kernel memory leak in QFX10002-32Q, QFX10002-60C, QFX10002-72Q, QFX10008, QFX10016 devices Flexible PIC Concentrators (FPCs) on Juniper Networks Junos OS allows an attacker to send genuine packets destined to the device to cause a Denial of Service (DoS) to the device. On QFX10002-32Q, QFX10002-60C, QFX10002-72Q devices the device will crash and restart. On QFX10008, QFX10016 devices, depending on the number of FPCs involved in an attack, one more more FPCs may crash and traffic through the device may be degraded in other ways, until the attack traffic stops. A reboot is required to restore service and clear the kernel memory. Continued receipt and processing of these genuine packets will create a sustained Denial of Service (DoS) condition. On QFX10008, QFX10016 devices, an indicator of compromise may be the existence of DCPFE core files. You can also monitor PFE memory utilization for incremental growth: user@qfx-RE:0% cprod -A fpc0 -c "show heap 0" | grep -i ke 0 3788a1b0 3221225048 2417120656 804104392 24 Kernel user@qfx-RE:0% cprod -A fpc0 -c "show heap 0" | grep -i ke 0 3788a1b0 3221225048 2332332200 888892848 27 Kernel This issue affects: Juniper Networks Junos OS on QFX10002-32Q, QFX10002-60C, QFX10002-72Q, QFX10008, QFX10016: 16.1 versions 16.1R1 and above prior to 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R3-S2; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R3; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2. This issue does not affect releases prior to Junos OS 16.1R1. This issue does not affect EX Series devices. This issue does not affect Junos OS Evolved.

Through routine static code analysis of the Juniper Networks Junos OS software codebase, the Secure Development Life Cycle team identified a Use After Free vulnerability in PFE packet processing on the QFX10002-60C switching platform. Exploitation of this vulnerability may allow a logically adjacent attacker to trigger a Denial of Service (DoS). Continued exploitation of this vulnerability will sustain the Denial of Service (DoS) condition. This issue only affects QFX10002-60C devices. No other product or platform is vulnerable to this issue. This issue affects Juniper Networks Junos OS on QFX10002-60C: 19.1 version 19.1R3-S1 and later versions; 19.1 versions prior to 19.1R3-S3; 19.2 version 19.2R2 and later versions; 19.2 versions prior to 19.2R3-S1; 20.2 versions prior to 20.2R1-S2. This issue does not affect Juniper Networks Junos OS: versions prior to 19.1R3; 19.2 versions prior to 19.2R2; any version of 19.3; version 20.2R2 and later releases.

A vulnerability due to the improper handling of direct memory access (DMA) buffers on EX4300 switches on Juniper Networks Junos OS allows an attacker sending specific unicast frames to trigger a Denial of Service (DoS) condition by exhausting DMA buffers, causing the FPC to crash and the device to restart. The DMA buffer leak is seen when receiving these specific, valid unicast frames on an interface without Layer 2 Protocol Tunneling (L2PT) or dot1x configured. Interfaces with either L2PT or dot1x configured are not vulnerable to this issue. When this issue occurs, DMA buffer usage keeps increasing and the following error log messages may be observed: Apr 14 14:29:34.360 /kernel: pid 64476 (pfex_junos), uid 0: exited on signal 11 (core dumped) Apr 14 14:29:33.790 init: pfe-manager (PID 64476) terminated by signal number 11. Core dumped! The DMA buffers on the FPC can be monitored by the executing vty command 'show heap': ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 4a46000 268435456 238230496 30204960 11 Kernel 1 18a46000 67108864 17618536 49490328 73 Bcm_sdk 2 23737000 117440512 18414552 99025960 84 DMA buf <<<<< keeps increasing 3 2a737000 16777216 16777216 0 0 DMA desc This issue affects Juniper Networks Junos OS on the EX4300: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2.

In Juniper Networks Junos OS Evolved an attacker sending certain valid BGP update packets may cause Junos OS Evolved to access an uninitialized pointer causing RPD to core leading to a Denial of Service (DoS). Continued receipt of these types of valid BGP update packets will cause an extended Denial of Service condition. RPD will require a restart to recover. An indicator of compromise is to see if the file rpd.re exists by issuing the command: show system core-dumps This issue affects: Juniper Networks Junos OS Evolved 19.4 versions prior to 19.4R2-S2-EVO; 20.1 versions prior to 20.1R1-S2-EVO, 20.1R2-S1-EVO. This issue does not affect Junos OS.

In an EVPN/VXLAN scenario, if an IRB interface with a virtual gateway address (VGA) is configured on a PE, a traffic loop may occur upon receipt of specific IP multicast traffic. The traffic loop will cause interface traffic to increase abnormally, ultimately leading to a Denial of Service (DoS) in packet processing. The following command could be used to monitor the interface traffic: user@junos> monitor interface traffic Interface Link Input packets (pps) Output packets (pps) et-0/0/1 Up 6492089274364 (70994959) 6492089235319 (70994956) et-0/0/25 Up 343458103 (1) 156844 (0) ae0 Up 9132519197257 (70994959) 9132519139454 (70994956) This issue affects Juniper Networks Junos OS on QFX Series: all versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S5, 18.4R3-S5; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S3; 19.2 versions prior to 19.2R1-S5, 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S2, 20.2R2.

An improper check for unusual or exceptional conditions vulnerability in Juniper Networks MX Series platforms with Trio-based MPC (Modular Port Concentrator) deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, may allow an attacker sending specific Layer 2 traffic to cause Distributed Denial of Service (DDoS) protection to trigger unexpectedly, resulting in traffic impact. Continued receipt and processing of this specific Layer 2 frames will sustain the Denial of Service (DoS) condition. An indication of compromise is to check DDOS LACP violations: user@device> show ddos-protection protocols statistics brief | match lacp This issue only affects the MX Series platforms with Trio-based MPC. No other products or platforms are affected. This issue affects: Juniper Networks Junos OS on MX Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2;

On Juniper Networks EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series deployed as a Virtual Chassis with a specific Layer 2 circuit configuration, Packet Forwarding Engine manager (FXPC) process may crash and restart upon receipt of specific layer 2 frames. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP Series, EX4600 Series, EX4650 Series, QFX5K Series 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4, 17.4R3-S5; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S7, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S2, 20.3R2;

A vulnerability in Juniper Networks Junos OS running on the ACX5448 and ACX710 platforms may cause BFD sessions to flap when a high rate of transit ARP packets are received. This, in turn, may impact routing protocols and network stability, leading to a Denial of Service (DoS) condition. When a high rate of transit ARP packets are exceptioned to the CPU and BFD flaps, the following log messages may be seen: bfdd[15864]: BFDD_STATE_UP_TO_DOWN: BFD Session 192.168.14.3 (IFL 232) state Up -> Down LD/RD(17/19) Up time:11:38:17 Local diag: CtlExpire Remote diag: None Reason: Detect Timer Expiry. bfdd[15864]: BFDD_TRAP_SHOP_STATE_DOWN: local discriminator: 17, new state: down, interface: irb.998, peer addr: 192.168.14.3 rpd[15839]: RPD_ISIS_ADJDOWN: IS-IS lost L2 adjacency to peer on irb.998, reason: BFD Session Down bfdd[15864]: BFDD_TRAP_SHOP_STATE_UP: local discriminator: 17, new state: up, interface: irb.998, peer addr: 192.168.14.3 This issue only affects the ACX5448 Series and ACX710 Series routers. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS: 18.2 versions prior to 18.2R3-S8 on ACX5448; 18.3 versions prior to 18.3R3-S5 on ACX5448; 18.4 versions prior to 18.4R1-S6, 18.4R3-S7 on ACX5448; 19.1 versions prior to 19.1R3-S5 on ACX5448; 19.2 versions prior to 19.2R2, 19.2R3 on ACX5448; 19.3 versions prior to 19.3R3 on ACX5448; 19.4 versions prior to 19.4R3 on ACX5448; 20.1 versions prior to 20.1R2 on ACX5448; 20.2 versions prior to 20.2R2 on ACX5448 and ACX710.

On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPCs (Modular Port Concentrators) where Integrated Routing and Bridging (IRB) interfaces are configured and mapped to a VPLS instance or a Bridge-Domain, certain Layer 2 network events at Customer Edge (CE) devices may cause memory leaks in the MPC of Provider Edge (PE) devices which can cause an out of memory condition and MPC restart. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines), including MX-MPC1-3D, MX-MPC1E-3D, MX-MPC2-3D, MX-MPC2E-3D, MPC-3D-16XGE, and CHAS-MXxx Series MPCs. No other products or platforms are affected by this issue. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S3; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.2 versions prior to 20.2R1-S3, 20.2R2; 20.3 versions prior to 20.3R1-S1,, 20.3R2. This issue does not affect Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R3-S2; 18.1; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R3-S1; 19.1; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2.

In Juniper Networks Junos OS Evolved, receipt of a stream of specific genuine Layer 2 frames may cause the Advanced Forwarding Toolkit (AFT) manager process (Evo-aftmand), responsible for handling Route, Class-of-Service (CoS), Firewall operations within the packet forwarding engine (PFE) to crash and restart, leading to a Denial of Service (DoS) condition. By continuously sending this specific stream of genuine Layer 2 frames, an attacker can repeatedly crash the PFE, causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R1-EVO. This issue does not affect Junos OS versions.

A Missing Synchronization vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on ACX5448 and ACX710 allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). If an interface flaps while the system gathers statistics on that interface, two processes simultaneously access a shared resource which leads to a PFE crash and restart. This issue affects Junos OS: * All versions before 20.4R3-S9, * 21.2 versions before 21.2R3-S5,  * 21.3 versions before 21.3R3-S5,  * 21.4 versions before 21.4R3-S4, * 22.1 versions before 22.1R3-S2, * 22.2 versions before 22.2R3-S2, * 22.3 versions before 22.3R2-S2, 22.3R3, * 22.4 versions before 22.4R2.