In the Linux kernel, the following vulnerability has been resolved: bpf, ktls: Fix data corruption when using bpf_msg_pop_data() in ktls When sending plaintext data, we initially calculated the corresponding ciphertext length. However, if we later reduced the plaintext data length via socket policy, we failed to recalculate the ciphertext length. This results in transmitting buffers containing uninitialized data during ciphertext transmission. This causes uninitialized bytes to be appended after a complete "Application Data" packet, leading to errors on the receiving end when parsing TLS record.

In the Linux kernel, the following vulnerability has been resolved: Revert "drm/prime: Use dma_buf from GEM object instance" This reverts commit f83a9b8c7fd0557b0c50784bfdc1bbe9140c9bf8. The dma_buf field in struct drm_gem_object is not stable over the object instance's lifetime. The field becomes NULL when user space releases the final GEM handle on the buffer object. This resulted in a NULL-pointer deref. Workarounds in commit 5307dce878d4 ("drm/gem: Acquire references on GEM handles for framebuffers") and commit f6bfc9afc751 ("drm/framebuffer: Acquire internal references on GEM handles") only solved the problem partially. They especially don't work for buffer objects without a DRM framebuffer associated. Hence, this revert to going back to using .import_attach->dmabuf. v3: - cc stable

In the Linux kernel, the following vulnerability has been resolved: net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY DSA has 2 kinds of drivers: 1. Those who call dsa_switch_suspend() and dsa_switch_resume() from their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz 2. Those who don't: all others. The above methods should be optional. For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(), and dsa_switch_resume() calls dsa_user_resume() -> phylink_start(). These seem good candidates for setting mac_managed_pm = true because that is essentially its definition [1], but that does not seem to be the biggest problem for now, and is not what this change focuses on. Talking strictly about the 2nd category of DSA drivers here (which do not have MAC managed PM, meaning that for their attached PHYs, mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full), I have noticed that the following warning from mdio_bus_phy_resume() is triggered: WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY && phydev->state != PHY_UP); because the PHY state machine is running. It's running as a result of a previous dsa_user_open() -> ... -> phylink_start() -> phy_start() having been initiated by the user. The previous mdio_bus_phy_suspend() was supposed to have called phy_stop_machine(), but it didn't. So this is why the PHY is in state PHY_NOLINK by the time mdio_bus_phy_resume() runs. mdio_bus_phy_suspend() did not call phy_stop_machine() because for phylink, the phydev->adjust_link function pointer is NULL. This seems a technicality introduced by commit fddd91016d16 ("phylib: fix PAL state machine restart on resume"). That commit was written before phylink existed, and was intended to avoid crashing with consumer drivers which don't use the PHY state machine - phylink always does, when using a PHY. But phylink itself has historically not been developed with suspend/resume in mind, and apparently not tested too much in that scenario, allowing this bug to exist unnoticed for so long. Plus, prior to the WARN_ON(), it would have likely been invisible. This issue is not in fact restricted to type 2 DSA drivers (according to the above ad-hoc classification), but can be extrapolated to any MAC driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where the issue was reported. Assuming mac_managed_pm is set correctly, a quick search indicates the following other drivers might be affected: $ grep -Zlr PHYLINK_NETDEV drivers/ | xargs -0 grep -L mac_managed_pm drivers/net/ethernet/atheros/ag71xx.c drivers/net/ethernet/microchip/sparx5/sparx5_main.c drivers/net/ethernet/microchip/lan966x/lan966x_main.c drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c drivers/net/ethernet/freescale/dpaa/dpaa_eth.c drivers/net/ethernet/freescale/ucc_geth.c drivers/net/ethernet/freescale/enetc/enetc_pf_common.c drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c drivers/net/ethernet/marvell/mvneta.c drivers/net/ethernet/marvell/prestera/prestera_main.c drivers/net/ethernet/mediatek/mtk_eth_soc.c drivers/net/ethernet/altera/altera_tse_main.c drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c drivers/net/ethernet/meta/fbnic/fbnic_phylink.c drivers/net/ethernet/tehuti/tn40_phy.c drivers/net/ethernet/mscc/ocelot_net.c Make the existing conditions dependent on the PHY device having a phydev->phy_link_change() implementation equal to the default phy_link_change() provided by phylib. Otherwise, we implicitly know that the phydev has the phylink-provided phylink_phy_change() callback, and when phylink is used, the PHY state machine always needs to be stopped/ started on the suspend/resume path. The code is structured as such that if phydev->phy_link_change() is absent, it is a matter of time until the kernel will crash - no need to further complicate the test. Thus, for the situation where the PM is not managed b ---truncated---

In the Linux kernel, the following vulnerability has been resolved: tcp: Correct signedness in skb remaining space calculation Syzkaller reported a bug [1] where sk->sk_forward_alloc can overflow. When we send data, if an skb exists at the tail of the write queue, the kernel will attempt to append the new data to that skb. However, the code that checks for available space in the skb is flawed: ''' copy = size_goal - skb->len ''' The types of the variables involved are: ''' copy: ssize_t (s64 on 64-bit systems) size_goal: int skb->len: unsigned int ''' Due to C's type promotion rules, the signed size_goal is converted to an unsigned int to match skb->len before the subtraction. The result is an unsigned int. When this unsigned int result is then assigned to the s64 copy variable, it is zero-extended, preserving its non-negative value. Consequently, copy is always >= 0. Assume we are sending 2GB of data and size_goal has been adjusted to a value smaller than skb->len. The subtraction will result in copy holding a very large positive integer. In the subsequent logic, this large value is used to update sk->sk_forward_alloc, which can easily cause it to overflow. The syzkaller reproducer uses TCP_REPAIR to reliably create this condition. However, this can also occur in real-world scenarios. The tcp_bound_to_half_wnd() function can also reduce size_goal to a small value. This would cause the subsequent tcp_wmem_schedule() to set sk->sk_forward_alloc to a value close to INT_MAX. Further memory allocation requests would then cause sk_forward_alloc to wrap around and become negative. [1]: https://syzkaller.appspot.com/bug?extid=de6565462ab540f50e47

In the Linux kernel, the following vulnerability has been resolved: nvmet-tcp: don't restore null sk_state_change queue->state_change is set as part of nvmet_tcp_set_queue_sock(), but if the TCP connection isn't established when nvmet_tcp_set_queue_sock() is called then queue->state_change isn't set and sock->sk->sk_state_change isn't replaced. As such we don't need to restore sock->sk->sk_state_change if queue->state_change is NULL. This avoids NULL pointer dereferences such as this: [ 286.462026][ C0] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 286.462814][ C0] #PF: supervisor instruction fetch in kernel mode [ 286.463796][ C0] #PF: error_code(0x0010) - not-present page [ 286.464392][ C0] PGD 8000000140620067 P4D 8000000140620067 PUD 114201067 PMD 0 [ 286.465086][ C0] Oops: Oops: 0010 [#1] SMP KASAN PTI [ 286.465559][ C0] CPU: 0 UID: 0 PID: 1628 Comm: nvme Not tainted 6.15.0-rc2+ #11 PREEMPT(voluntary) [ 286.466393][ C0] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 [ 286.467147][ C0] RIP: 0010:0x0 [ 286.467420][ C0] Code: Unable to access opcode bytes at 0xffffffffffffffd6. [ 286.467977][ C0] RSP: 0018:ffff8883ae008580 EFLAGS: 00010246 [ 286.468425][ C0] RAX: 0000000000000000 RBX: ffff88813fd34100 RCX: ffffffffa386cc43 [ 286.469019][ C0] RDX: 1ffff11027fa68b6 RSI: 0000000000000008 RDI: ffff88813fd34100 [ 286.469545][ C0] RBP: ffff88813fd34160 R08: 0000000000000000 R09: ffffed1027fa682c [ 286.470072][ C0] R10: ffff88813fd34167 R11: 0000000000000000 R12: ffff88813fd344c3 [ 286.470585][ C0] R13: ffff88813fd34112 R14: ffff88813fd34aec R15: ffff888132cdd268 [ 286.471070][ C0] FS: 00007fe3c04c7d80(0000) GS:ffff88840743f000(0000) knlGS:0000000000000000 [ 286.471644][ C0] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 286.472543][ C0] CR2: ffffffffffffffd6 CR3: 000000012daca000 CR4: 00000000000006f0 [ 286.473500][ C0] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 286.474467][ C0] DR3: 0000000000000000 DR6: 00000000ffff07f0 DR7: 0000000000000400 [ 286.475453][ C0] Call Trace: [ 286.476102][ C0] <IRQ> [ 286.476719][ C0] tcp_fin+0x2bb/0x440 [ 286.477429][ C0] tcp_data_queue+0x190f/0x4e60 [ 286.478174][ C0] ? __build_skb_around+0x234/0x330 [ 286.478940][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.479659][ C0] ? __pfx_tcp_data_queue+0x10/0x10 [ 286.480431][ C0] ? tcp_try_undo_loss+0x640/0x6c0 [ 286.481196][ C0] ? seqcount_lockdep_reader_access.constprop.0+0x82/0x90 [ 286.482046][ C0] ? kvm_clock_get_cycles+0x14/0x30 [ 286.482769][ C0] ? ktime_get+0x66/0x150 [ 286.483433][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.484146][ C0] tcp_rcv_established+0x6e4/0x2050 [ 286.484857][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.485523][ C0] ? ipv4_dst_check+0x160/0x2b0 [ 286.486203][ C0] ? __pfx_tcp_rcv_established+0x10/0x10 [ 286.486917][ C0] ? lock_release+0x217/0x2c0 [ 286.487595][ C0] tcp_v4_do_rcv+0x4d6/0x9b0 [ 286.488279][ C0] tcp_v4_rcv+0x2af8/0x3e30 [ 286.488904][ C0] ? raw_local_deliver+0x51b/0xad0 [ 286.489551][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.490198][ C0] ? __pfx_tcp_v4_rcv+0x10/0x10 [ 286.490813][ C0] ? __pfx_raw_local_deliver+0x10/0x10 [ 286.491487][ C0] ? __pfx_nf_confirm+0x10/0x10 [nf_conntrack] [ 286.492275][ C0] ? rcu_is_watching+0x11/0xb0 [ 286.492900][ C0] ip_protocol_deliver_rcu+0x8f/0x370 [ 286.493579][ C0] ip_local_deliver_finish+0x297/0x420 [ 286.494268][ C0] ip_local_deliver+0x168/0x430 [ 286.494867][ C0] ? __pfx_ip_local_deliver+0x10/0x10 [ 286.495498][ C0] ? __pfx_ip_local_deliver_finish+0x10/0x10 [ 286.496204][ C0] ? ip_rcv_finish_core+0x19a/0x1f20 [ 286.496806][ C0] ? lock_release+0x217/0x2c0 [ 286.497414][ C0] ip_rcv+0x455/0x6e0 [ 286.497945][ C0] ? __pfx_ip_rcv+0x10/0x10 [ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: fbdev: imxfb: Check fb_add_videomode to prevent null-ptr-deref fb_add_videomode() can fail with -ENOMEM when its internal kmalloc() cannot allocate a struct fb_modelist. If that happens, the modelist stays empty but the driver continues to register. Add a check for its return value to prevent poteintial null-ptr-deref, which is similar to the commit 17186f1f90d3 ("fbdev: Fix do_register_framebuffer to prevent null-ptr-deref in fb_videomode_to_var").

In the Linux kernel, the following vulnerability has been resolved: clk: imx95-blk-ctl: Fix synchronous abort When enabling runtime PM for clock suppliers that also belong to a power domain, the following crash is thrown: error: synchronous external abort: 0000000096000010 [#1] PREEMPT SMP Workqueue: events_unbound deferred_probe_work_func pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : clk_mux_get_parent+0x60/0x90 lr : clk_core_reparent_orphans_nolock+0x58/0xd8 Call trace: clk_mux_get_parent+0x60/0x90 clk_core_reparent_orphans_nolock+0x58/0xd8 of_clk_add_hw_provider.part.0+0x90/0x100 of_clk_add_hw_provider+0x1c/0x38 imx95_bc_probe+0x2e0/0x3f0 platform_probe+0x70/0xd8 Enabling runtime PM without explicitly resuming the device caused the power domain cut off after clk_register() is called. As a result, a crash happens when the clock hardware provider is added and attempts to access the BLK_CTL register. Fix this by using devm_pm_runtime_enable() instead of pm_runtime_enable() and getting rid of the pm_runtime_disable() in the cleanup path.

In the Linux kernel, the following vulnerability has been resolved: iio: common: st_sensors: Fix use of uninitialize device structs Throughout the various probe functions &indio_dev->dev is used before it is initialized. This caused a kernel panic in st_sensors_power_enable() when the call to devm_regulator_bulk_get_enable() fails and then calls dev_err_probe() with the uninitialized device. This seems to only cause a panic with dev_err_probe(), dev_err(), dev_warn() and dev_info() don't seem to cause a panic, but are fixed as well. The issue is reported and traced here: [1]

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix invalid inode pointer dereferences during log replay In a few places where we call read_one_inode(), if we get a NULL pointer we end up jumping into an error path, or fallthrough in case of __add_inode_ref(), where we then do something like this: iput(&inode->vfs_inode); which results in an invalid inode pointer that triggers an invalid memory access, resulting in a crash. Fix this by making sure we don't do such dereferences.

In the Linux kernel, the following vulnerability has been resolved: iommu: Fix two issues in iommu_copy_struct_from_user() In the review for iommu_copy_struct_to_user() helper, Matt pointed out that a NULL pointer should be rejected prior to dereferencing it: https://lore.kernel.org/all/86881827-8E2D-461C-BDA3-FA8FD14C343C@nvidia.com And Alok pointed out a typo at the same time: https://lore.kernel.org/all/480536af-6830-43ce-a327-adbd13dc3f1d@oracle.com Since both issues were copied from iommu_copy_struct_from_user(), fix them first in the current header.

In the Linux kernel, the following vulnerability has been resolved: ACPICA: Refuse to evaluate a method if arguments are missing As reported in [1], a platform firmware update that increased the number of method parameters and forgot to update a least one of its callers, caused ACPICA to crash due to use-after-free. Since this a result of a clear AML issue that arguably cannot be fixed up by the interpreter (it cannot produce missing data out of thin air), address it by making ACPICA refuse to evaluate a method if the caller attempts to pass fewer arguments than expected to it.

In the Linux kernel, the following vulnerability has been resolved: nfsd: Initialize ssc before laundromat_work to prevent NULL dereference In nfs4_state_start_net(), laundromat_work may access nfsd_ssc through nfs4_laundromat -> nfsd4_ssc_expire_umount. If nfsd_ssc isn't initialized, this can cause NULL pointer dereference. Normally the delayed start of laundromat_work allows sufficient time for nfsd_ssc initialization to complete. However, when the kernel waits too long for userspace responses (e.g. in nfs4_state_start_net -> nfsd4_end_grace -> nfsd4_record_grace_done -> nfsd4_cld_grace_done -> cld_pipe_upcall -> __cld_pipe_upcall -> wait_for_completion path), the delayed work may start before nfsd_ssc initialization finishes. Fix this by moving nfsd_ssc initialization before starting laundromat_work.

In the Linux kernel, the following vulnerability has been resolved: hwmon: (asus-ec-sensors) check sensor index in read_string() Prevent a potential invalid memory access when the requested sensor is not found. find_ec_sensor_index() may return a negative value (e.g. -ENOENT), but its result was used without checking, which could lead to undefined behavior when passed to get_sensor_info(). Add a proper check to return -EINVAL if sensor_index is negative. Found by Linux Verification Center (linuxtesting.org) with SVACE. [groeck: Return error code returned from find_ec_sensor_index]

In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: QOS: Refactor TC_HTB_LEAF_DEL_LAST callback This patch addresses below issues, 1. Active traffic on the leaf node must be stopped before its send queue is reassigned to the parent. This patch resolves the issue by marking the node as 'Inner'. 2. During a system reboot, the interface receives TC_HTB_LEAF_DEL and TC_HTB_LEAF_DEL_LAST callbacks to delete its HTB queues. In the case of TC_HTB_LEAF_DEL_LAST, although the same send queue is reassigned to the parent, the current logic still attempts to update the real number of queues, leadning to below warnings New queues can't be registered after device unregistration. WARNING: CPU: 0 PID: 6475 at net/core/net-sysfs.c:1714 netdev_queue_update_kobjects+0x1e4/0x200

In the Linux kernel, the following vulnerability has been resolved: mptcp: make fallback action and fallback decision atomic Syzkaller reported the following splat: WARNING: CPU: 1 PID: 7704 at net/mptcp/protocol.h:1223 __mptcp_do_fallback net/mptcp/protocol.h:1223 [inline] WARNING: CPU: 1 PID: 7704 at net/mptcp/protocol.h:1223 mptcp_do_fallback net/mptcp/protocol.h:1244 [inline] WARNING: CPU: 1 PID: 7704 at net/mptcp/protocol.h:1223 check_fully_established net/mptcp/options.c:982 [inline] WARNING: CPU: 1 PID: 7704 at net/mptcp/protocol.h:1223 mptcp_incoming_options+0x21a8/0x2510 net/mptcp/options.c:1153 Modules linked in: CPU: 1 UID: 0 PID: 7704 Comm: syz.3.1419 Not tainted 6.16.0-rc3-gbd5ce2324dba #20 PREEMPT(voluntary) Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:__mptcp_do_fallback net/mptcp/protocol.h:1223 [inline] RIP: 0010:mptcp_do_fallback net/mptcp/protocol.h:1244 [inline] RIP: 0010:check_fully_established net/mptcp/options.c:982 [inline] RIP: 0010:mptcp_incoming_options+0x21a8/0x2510 net/mptcp/options.c:1153 Code: 24 18 e8 bb 2a 00 fd e9 1b df ff ff e8 b1 21 0f 00 e8 ec 5f c4 fc 44 0f b7 ac 24 b0 00 00 00 e9 54 f1 ff ff e8 d9 5f c4 fc 90 <0f> 0b 90 e9 b8 f4 ff ff e8 8b 2a 00 fd e9 8d e6 ff ff e8 81 2a 00 RSP: 0018:ffff8880a3f08448 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff8880180a8000 RCX: ffffffff84afcf45 RDX: ffff888090223700 RSI: ffffffff84afdaa7 RDI: 0000000000000001 RBP: ffff888017955780 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000 R13: ffff8880180a8910 R14: ffff8880a3e9d058 R15: 0000000000000000 FS: 00005555791b8500(0000) GS:ffff88811c495000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000110c2800b7 CR3: 0000000058e44000 CR4: 0000000000350ef0 Call Trace: <IRQ> tcp_reset+0x26f/0x2b0 net/ipv4/tcp_input.c:4432 tcp_validate_incoming+0x1057/0x1b60 net/ipv4/tcp_input.c:5975 tcp_rcv_established+0x5b5/0x21f0 net/ipv4/tcp_input.c:6166 tcp_v4_do_rcv+0x5dc/0xa70 net/ipv4/tcp_ipv4.c:1925 tcp_v4_rcv+0x3473/0x44a0 net/ipv4/tcp_ipv4.c:2363 ip_protocol_deliver_rcu+0xba/0x480 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x2f1/0x500 net/ipv4/ip_input.c:233 NF_HOOK include/linux/netfilter.h:317 [inline] NF_HOOK include/linux/netfilter.h:311 [inline] ip_local_deliver+0x1be/0x560 net/ipv4/ip_input.c:254 dst_input include/net/dst.h:469 [inline] ip_rcv_finish net/ipv4/ip_input.c:447 [inline] NF_HOOK include/linux/netfilter.h:317 [inline] NF_HOOK include/linux/netfilter.h:311 [inline] ip_rcv+0x514/0x810 net/ipv4/ip_input.c:567 __netif_receive_skb_one_core+0x197/0x1e0 net/core/dev.c:5975 __netif_receive_skb+0x1f/0x120 net/core/dev.c:6088 process_backlog+0x301/0x1360 net/core/dev.c:6440 __napi_poll.constprop.0+0xba/0x550 net/core/dev.c:7453 napi_poll net/core/dev.c:7517 [inline] net_rx_action+0xb44/0x1010 net/core/dev.c:7644 handle_softirqs+0x1d0/0x770 kernel/softirq.c:579 do_softirq+0x3f/0x90 kernel/softirq.c:480 </IRQ> <TASK> __local_bh_enable_ip+0xed/0x110 kernel/softirq.c:407 local_bh_enable include/linux/bottom_half.h:33 [inline] inet_csk_listen_stop+0x2c5/0x1070 net/ipv4/inet_connection_sock.c:1524 mptcp_check_listen_stop.part.0+0x1cc/0x220 net/mptcp/protocol.c:2985 mptcp_check_listen_stop net/mptcp/mib.h:118 [inline] __mptcp_close+0x9b9/0xbd0 net/mptcp/protocol.c:3000 mptcp_close+0x2f/0x140 net/mptcp/protocol.c:3066 inet_release+0xed/0x200 net/ipv4/af_inet.c:435 inet6_release+0x4f/0x70 net/ipv6/af_inet6.c:487 __sock_release+0xb3/0x270 net/socket.c:649 sock_close+0x1c/0x30 net/socket.c:1439 __fput+0x402/0xb70 fs/file_table.c:465 task_work_run+0x150/0x240 kernel/task_work.c:227 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] exit_to_user_mode_loop+0xd4 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: hisi_acc_vfio_pci: fix XQE dma address error The dma addresses of EQE and AEQE are wrong after migration and results in guest kernel-mode encryption services failure. Comparing the definition of hardware registers, we found that there was an error when the data read from the register was combined into an address. Therefore, the address combination sequence needs to be corrected. Even after fixing the above problem, we still have an issue where the Guest from an old kernel can get migrated to new kernel and may result in wrong data. In order to ensure that the address is correct after migration, if an old magic number is detected, the dma address needs to be updated.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: eir: Fix possible crashes on eir_create_adv_data eir_create_adv_data may attempt to add EIR_FLAGS and EIR_TX_POWER without checking if that would fit.

In the Linux kernel, the following vulnerability has been resolved: fpga: fix potential null pointer deref in fpga_mgr_test_img_load_sgt() fpga_mgr_test_img_load_sgt() allocates memory for sgt using kunit_kzalloc() however it does not check if the allocation failed. It then passes sgt to sg_alloc_table(), which passes it to __sg_alloc_table(). This function calls memset() on sgt in an attempt to zero it out. If the allocation fails then sgt will be NULL and the memset will trigger a NULL pointer dereference. Fix this by checking the allocation with KUNIT_ASSERT_NOT_ERR_OR_NULL().

In the Linux kernel, the following vulnerability has been resolved: bcache: fix NULL pointer in cache_set_flush() 1. LINE#1794 - LINE#1887 is some codes about function of bch_cache_set_alloc(). 2. LINE#2078 - LINE#2142 is some codes about function of register_cache_set(). 3. register_cache_set() will call bch_cache_set_alloc() in LINE#2098. 1794 struct cache_set *bch_cache_set_alloc(struct cache_sb *sb) 1795 { ... 1860 if (!(c->devices = kcalloc(c->nr_uuids, sizeof(void *), GFP_KERNEL)) || 1861 mempool_init_slab_pool(&c->search, 32, bch_search_cache) || 1862 mempool_init_kmalloc_pool(&c->bio_meta, 2, 1863 sizeof(struct bbio) + sizeof(struct bio_vec) * 1864 bucket_pages(c)) || 1865 mempool_init_kmalloc_pool(&c->fill_iter, 1, iter_size) || 1866 bioset_init(&c->bio_split, 4, offsetof(struct bbio, bio), 1867 BIOSET_NEED_BVECS|BIOSET_NEED_RESCUER) || 1868 !(c->uuids = alloc_bucket_pages(GFP_KERNEL, c)) || 1869 !(c->moving_gc_wq = alloc_workqueue("bcache_gc", 1870 WQ_MEM_RECLAIM, 0)) || 1871 bch_journal_alloc(c) || 1872 bch_btree_cache_alloc(c) || 1873 bch_open_buckets_alloc(c) || 1874 bch_bset_sort_state_init(&c->sort, ilog2(c->btree_pages))) 1875 goto err; ^^^^^^^^ 1876 ... 1883 return c; 1884 err: 1885 bch_cache_set_unregister(c); ^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1886 return NULL; 1887 } ... 2078 static const char *register_cache_set(struct cache *ca) 2079 { ... 2098 c = bch_cache_set_alloc(&ca->sb); 2099 if (!c) 2100 return err; ^^^^^^^^^^ ... 2128 ca->set = c; 2129 ca->set->cache[ca->sb.nr_this_dev] = ca; ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ... 2138 return NULL; 2139 err: 2140 bch_cache_set_unregister(c); 2141 return err; 2142 } (1) If LINE#1860 - LINE#1874 is true, then do 'goto err'(LINE#1875) and call bch_cache_set_unregister()(LINE#1885). (2) As (1) return NULL(LINE#1886), LINE#2098 - LINE#2100 would return. (3) As (2) has returned, LINE#2128 - LINE#2129 would do *not* give the value to c->cache[], it means that c->cache[] is NULL. LINE#1624 - LINE#1665 is some codes about function of cache_set_flush(). As (1), in LINE#1885 call bch_cache_set_unregister() ---> bch_cache_set_stop() ---> closure_queue() -.-> cache_set_flush() (as below LINE#1624) 1624 static void cache_set_flush(struct closure *cl) 1625 { ... 1654 for_each_cache(ca, c, i) 1655 if (ca->alloc_thread) ^^ 1656 kthread_stop(ca->alloc_thread); ... 1665 } (4) In LINE#1655 ca is NULL(see (3)) in cache_set_flush() then the kernel crash occurred as below: [ 846.712887] bcache: register_cache() error drbd6: cannot allocate memory [ 846.713242] bcache: register_bcache() error : failed to register device [ 846.713336] bcache: cache_set_free() Cache set 2f84bdc1-498a-4f2f-98a7-01946bf54287 unregistered [ 846.713768] BUG: unable to handle kernel NULL pointer dereference at 00000000000009f8 [ 846.714790] PGD 0 P4D 0 [ 846.715129] Oops: 0000 [#1] SMP PTI [ 846.715472] CPU: 19 PID: 5057 Comm: kworker/19:16 Kdump: loaded Tainted: G OE --------- - - 4.18.0-147.5.1.el8_1.5es.3.x86_64 #1 [ 846.716082] Hardware name: ESPAN GI-25212/X11DPL-i, BIOS 2.1 06/15/2018 [ 846.716451] Workqueue: events cache_set_flush [bcache] [ 846.716808] RIP: 0010:cache_set_flush+0xc9/0x1b0 [bcache] [ 846.717155] Code: 00 4c 89 a5 b0 03 00 00 48 8b 85 68 f6 ff ff a8 08 0f 84 88 00 00 00 31 db 66 83 bd 3c f7 ff ff 00 48 8b 85 48 ff ff ff 74 28 <48> 8b b8 f8 09 00 0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/gem: Acquire references on GEM handles for framebuffers A GEM handle can be released while the GEM buffer object is attached to a DRM framebuffer. This leads to the release of the dma-buf backing the buffer object, if any. [1] Trying to use the framebuffer in further mode-setting operations leads to a segmentation fault. Most easily happens with driver that use shadow planes for vmap-ing the dma-buf during a page flip. An example is shown below. [ 156.791968] ------------[ cut here ]------------ [ 156.796830] WARNING: CPU: 2 PID: 2255 at drivers/dma-buf/dma-buf.c:1527 dma_buf_vmap+0x224/0x430 [...] [ 156.942028] RIP: 0010:dma_buf_vmap+0x224/0x430 [ 157.043420] Call Trace: [ 157.045898] <TASK> [ 157.048030] ? show_trace_log_lvl+0x1af/0x2c0 [ 157.052436] ? show_trace_log_lvl+0x1af/0x2c0 [ 157.056836] ? show_trace_log_lvl+0x1af/0x2c0 [ 157.061253] ? drm_gem_shmem_vmap+0x74/0x710 [ 157.065567] ? dma_buf_vmap+0x224/0x430 [ 157.069446] ? __warn.cold+0x58/0xe4 [ 157.073061] ? dma_buf_vmap+0x224/0x430 [ 157.077111] ? report_bug+0x1dd/0x390 [ 157.080842] ? handle_bug+0x5e/0xa0 [ 157.084389] ? exc_invalid_op+0x14/0x50 [ 157.088291] ? asm_exc_invalid_op+0x16/0x20 [ 157.092548] ? dma_buf_vmap+0x224/0x430 [ 157.096663] ? dma_resv_get_singleton+0x6d/0x230 [ 157.101341] ? __pfx_dma_buf_vmap+0x10/0x10 [ 157.105588] ? __pfx_dma_resv_get_singleton+0x10/0x10 [ 157.110697] drm_gem_shmem_vmap+0x74/0x710 [ 157.114866] drm_gem_vmap+0xa9/0x1b0 [ 157.118763] drm_gem_vmap_unlocked+0x46/0xa0 [ 157.123086] drm_gem_fb_vmap+0xab/0x300 [ 157.126979] drm_atomic_helper_prepare_planes.part.0+0x487/0xb10 [ 157.133032] ? lockdep_init_map_type+0x19d/0x880 [ 157.137701] drm_atomic_helper_commit+0x13d/0x2e0 [ 157.142671] ? drm_atomic_nonblocking_commit+0xa0/0x180 [ 157.147988] drm_mode_atomic_ioctl+0x766/0xe40 [...] [ 157.346424] ---[ end trace 0000000000000000 ]--- Acquiring GEM handles for the framebuffer's GEM buffer objects prevents this from happening. The framebuffer's cleanup later puts the handle references. Commit 1a148af06000 ("drm/gem-shmem: Use dma_buf from GEM object instance") triggers the segmentation fault easily by using the dma-buf field more widely. The underlying issue with reference counting has been present before. v2: - acquire the handle instead of the BO (Christian) - fix comment style (Christian) - drop the Fixes tag (Christian) - rename err_ gotos - add missing Link tag

In the Linux kernel, the following vulnerability has been resolved: firmware: arm_ffa: Replace mutex with rwlock to avoid sleep in atomic context The current use of a mutex to protect the notifier hashtable accesses can lead to issues in the atomic context. It results in the below kernel warnings: | BUG: sleeping function called from invalid context at kernel/locking/mutex.c:258 | in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 9, name: kworker/0:0 | preempt_count: 1, expected: 0 | RCU nest depth: 0, expected: 0 | CPU: 0 UID: 0 PID: 9 Comm: kworker/0:0 Not tainted 6.14.0 #4 | Workqueue: ffa_pcpu_irq_notification notif_pcpu_irq_work_fn | Call trace: | show_stack+0x18/0x24 (C) | dump_stack_lvl+0x78/0x90 | dump_stack+0x18/0x24 | __might_resched+0x114/0x170 | __might_sleep+0x48/0x98 | mutex_lock+0x24/0x80 | handle_notif_callbacks+0x54/0xe0 | notif_get_and_handle+0x40/0x88 | generic_exec_single+0x80/0xc0 | smp_call_function_single+0xfc/0x1a0 | notif_pcpu_irq_work_fn+0x2c/0x38 | process_one_work+0x14c/0x2b4 | worker_thread+0x2e4/0x3e0 | kthread+0x13c/0x210 | ret_from_fork+0x10/0x20 To address this, replace the mutex with an rwlock to protect the notifier hashtable accesses. This ensures that read-side locking does not sleep and multiple readers can acquire the lock concurrently, avoiding unnecessary contention and potential deadlocks. Writer access remains exclusive, preserving correctness. This change resolves warnings from lockdep about potential sleep in atomic context.

In the Linux kernel, the following vulnerability has been resolved: smb: client: fix warning when reconnecting channel When reconnecting a channel in smb2_reconnect_server(), a dummy tcon is passed down to smb2_reconnect() with ->query_interface uninitialized, so we can't call queue_delayed_work() on it. Fix the following warning by ensuring that we're queueing the delayed worker from correct tcon. WARNING: CPU: 4 PID: 1126 at kernel/workqueue.c:2498 __queue_delayed_work+0x1d2/0x200 Modules linked in: cifs cifs_arc4 nls_ucs2_utils cifs_md4 [last unloaded: cifs] CPU: 4 UID: 0 PID: 1126 Comm: kworker/4:0 Not tainted 6.16.0-rc3 #5 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-4.fc42 04/01/2014 Workqueue: cifsiod smb2_reconnect_server [cifs] RIP: 0010:__queue_delayed_work+0x1d2/0x200 Code: 41 5e 41 5f e9 7f ee ff ff 90 0f 0b 90 e9 5d ff ff ff bf 02 00 00 00 e8 6c f3 07 00 89 c3 eb bd 90 0f 0b 90 e9 57 f> 0b 90 e9 65 fe ff ff 90 0f 0b 90 e9 72 fe ff ff 90 0f 0b 90 e9 RSP: 0018:ffffc900014afad8 EFLAGS: 00010003 RAX: 0000000000000000 RBX: ffff888124d99988 RCX: ffffffff81399cc1 RDX: dffffc0000000000 RSI: ffff888114326e00 RDI: ffff888124d999f0 RBP: 000000000000ea60 R08: 0000000000000001 R09: ffffed10249b3331 R10: ffff888124d9998f R11: 0000000000000004 R12: 0000000000000040 R13: ffff888114326e00 R14: ffff888124d999d8 R15: ffff888114939020 FS: 0000000000000000(0000) GS:ffff88829f7fe000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007ffe7a2b4038 CR3: 0000000120a6f000 CR4: 0000000000750ef0 PKRU: 55555554 Call Trace: <TASK> queue_delayed_work_on+0xb4/0xc0 smb2_reconnect+0xb22/0xf50 [cifs] smb2_reconnect_server+0x413/0xd40 [cifs] ? __pfx_smb2_reconnect_server+0x10/0x10 [cifs] ? local_clock_noinstr+0xd/0xd0 ? local_clock+0x15/0x30 ? lock_release+0x29b/0x390 process_one_work+0x4c5/0xa10 ? __pfx_process_one_work+0x10/0x10 ? __list_add_valid_or_report+0x37/0x120 worker_thread+0x2f1/0x5a0 ? __kthread_parkme+0xde/0x100 ? __pfx_worker_thread+0x10/0x10 kthread+0x1fe/0x380 ? kthread+0x10f/0x380 ? __pfx_kthread+0x10/0x10 ? local_clock_noinstr+0xd/0xd0 ? ret_from_fork+0x1b/0x1f0 ? local_clock+0x15/0x30 ? lock_release+0x29b/0x390 ? rcu_is_watching+0x20/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x15b/0x1f0 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> irq event stamp: 1116206 hardirqs last enabled at (1116205): [<ffffffff8143af42>] __up_console_sem+0x52/0x60 hardirqs last disabled at (1116206): [<ffffffff81399f0e>] queue_delayed_work_on+0x6e/0xc0 softirqs last enabled at (1116138): [<ffffffffc04562fd>] __smb_send_rqst+0x42d/0x950 [cifs] softirqs last disabled at (1116136): [<ffffffff823d35e1>] release_sock+0x21/0xf0

In the Linux kernel, the following vulnerability has been resolved: crypto: marvell/cesa - Handle zero-length skcipher requests Do not access random memory for zero-length skcipher requests. Just return 0.

In the Linux kernel, the following vulnerability has been resolved: Revert "drm/gem-shmem: Use dma_buf from GEM object instance" This reverts commit 1a148af06000e545e714fe3210af3d77ff903c11. The dma_buf field in struct drm_gem_object is not stable over the object instance's lifetime. The field becomes NULL when user space releases the final GEM handle on the buffer object. This resulted in a NULL-pointer deref. Workarounds in commit 5307dce878d4 ("drm/gem: Acquire references on GEM handles for framebuffers") and commit f6bfc9afc751 ("drm/framebuffer: Acquire internal references on GEM handles") only solved the problem partially. They especially don't work for buffer objects without a DRM framebuffer associated. Hence, this revert to going back to using .import_attach->dmabuf. v3: - cc stable

In the Linux kernel, the following vulnerability has been resolved: ksmbd: discard write access to the directory open may_open() does not allow a directory to be opened with the write access. However, some writing flags set by client result in adding write access on server, making ksmbd incompatible with FUSE file system. Simply, let's discard the write access when opening a directory. list_add corruption. next is NULL. ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:26! pc : __list_add_valid+0x88/0xbc lr : __list_add_valid+0x88/0xbc Call trace: __list_add_valid+0x88/0xbc fuse_finish_open+0x11c/0x170 fuse_open_common+0x284/0x5e8 fuse_dir_open+0x14/0x24 do_dentry_open+0x2a4/0x4e0 dentry_open+0x50/0x80 smb2_open+0xbe4/0x15a4 handle_ksmbd_work+0x478/0x5ec process_one_work+0x1b4/0x448 worker_thread+0x25c/0x430 kthread+0x104/0x1d4 ret_from_fork+0x10/0x20

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to trigger foreground gc during f2fs_map_blocks() in lfs mode w/ "mode=lfs" mount option, generic/299 will cause system panic as below: ------------[ cut here ]------------ kernel BUG at fs/f2fs/segment.c:2835! Call Trace: <TASK> f2fs_allocate_data_block+0x6f4/0xc50 f2fs_map_blocks+0x970/0x1550 f2fs_iomap_begin+0xb2/0x1e0 iomap_iter+0x1d6/0x430 __iomap_dio_rw+0x208/0x9a0 f2fs_file_write_iter+0x6b3/0xfa0 aio_write+0x15d/0x2e0 io_submit_one+0x55e/0xab0 __x64_sys_io_submit+0xa5/0x230 do_syscall_64+0x84/0x2f0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0010:new_curseg+0x70f/0x720 The root cause of we run out-of-space is: in f2fs_map_blocks(), f2fs may trigger foreground gc only if it allocates any physical block, it will be a little bit later when there is multiple threads writing data w/ aio/dio/bufio method in parallel, since we always use OPU in lfs mode, so f2fs_map_blocks() does block allocations aggressively. In order to fix this issue, let's give a chance to trigger foreground gc in prior to block allocation in f2fs_map_blocks().

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix null check of pipe_ctx->plane_state for update_dchubp_dpp Similar to commit 6a057072ddd1 ("drm/amd/display: Fix null check for pipe_ctx->plane_state in dcn20_program_pipe") that addresses a null pointer dereference on dcn20_update_dchubp_dpp. This is the same function hooked for update_dchubp_dpp in dcn401, with the same issue. Fix possible null pointer deference on dcn401_program_pipe too. (cherry picked from commit d8d47f739752227957d8efc0cb894761bfe1d879)

In the Linux kernel, the following vulnerability has been resolved: x86/mm: Check return value from memblock_phys_alloc_range() At least with CONFIG_PHYSICAL_START=0x100000, if there is < 4 MiB of contiguous free memory available at this point, the kernel will crash and burn because memblock_phys_alloc_range() returns 0 on failure, which leads memblock_phys_free() to throw the first 4 MiB of physical memory to the wolves. At a minimum it should fail gracefully with a meaningful diagnostic, but in fact everything seems to work fine without the weird reserve allocation.

In the Linux kernel, the following vulnerability has been resolved: riscv: Fix kernel crash due to PR_SET_TAGGED_ADDR_CTRL When userspace does PR_SET_TAGGED_ADDR_CTRL, but Supm extension is not available, the kernel crashes: Oops - illegal instruction [#1] [snip] epc : set_tagged_addr_ctrl+0x112/0x15a ra : set_tagged_addr_ctrl+0x74/0x15a epc : ffffffff80011ace ra : ffffffff80011a30 sp : ffffffc60039be10 [snip] status: 0000000200000120 badaddr: 0000000010a79073 cause: 0000000000000002 set_tagged_addr_ctrl+0x112/0x15a __riscv_sys_prctl+0x352/0x73c do_trap_ecall_u+0x17c/0x20c andle_exception+0x150/0x15c Fix it by checking if Supm is available.

In the Linux kernel, the following vulnerability has been resolved: padata: do not leak refcount in reorder_work A recent patch that addressed a UAF introduced a reference count leak: the parallel_data refcount is incremented unconditionally, regardless of the return value of queue_work(). If the work item is already queued, the incremented refcount is never decremented. Fix this by checking the return value of queue_work() and decrementing the refcount when necessary. Resolves: Unreferenced object 0xffff9d9f421e3d80 (size 192): comm "cryptomgr_probe", pid 157, jiffies 4294694003 hex dump (first 32 bytes): 80 8b cf 41 9f 9d ff ff b8 97 e0 89 ff ff ff ff ...A............ d0 97 e0 89 ff ff ff ff 19 00 00 00 1f 88 23 00 ..............#. backtrace (crc 838fb36): __kmalloc_cache_noprof+0x284/0x320 padata_alloc_pd+0x20/0x1e0 padata_alloc_shell+0x3b/0xa0 0xffffffffc040a54d cryptomgr_probe+0x43/0xc0 kthread+0xf6/0x1f0 ret_from_fork+0x2f/0x50 ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: nvmet: pci-epf: Do not complete commands twice if nvmet_req_init() fails Have nvmet_req_init() and req->execute() complete failed commands. Description of the problem: nvmet_req_init() calls __nvmet_req_complete() internally upon failure, e.g., unsupported opcode, which calls the "queue_response" callback, this results in nvmet_pci_epf_queue_response() being called, which will call nvmet_pci_epf_complete_iod() if data_len is 0 or if dma_dir is different from DMA_TO_DEVICE. This results in a double completion as nvmet_pci_epf_exec_iod_work() also calls nvmet_pci_epf_complete_iod() when nvmet_req_init() fails. Steps to reproduce: On the host send a command with an unsupported opcode with nvme-cli, For example the admin command "security receive" $ sudo nvme security-recv /dev/nvme0n1 -n1 -x4096 This triggers a double completion as nvmet_req_init() fails and nvmet_pci_epf_queue_response() is called, here iod->dma_dir is still in the default state of "DMA_NONE" as set by default in nvmet_pci_epf_alloc_iod(), so nvmet_pci_epf_complete_iod() is called. Because nvmet_req_init() failed nvmet_pci_epf_complete_iod() is also called in nvmet_pci_epf_exec_iod_work() leading to a double completion. This not only sends two completions to the host but also corrupts the state of the PCI NVMe target leading to kernel oops. This patch lets nvmet_req_init() and req->execute() complete all failed commands, and removes the double completion case in nvmet_pci_epf_exec_iod_work() therefore fixing the edge cases where double completions occurred.

In the Linux kernel, the following vulnerability has been resolved: wifi: mt76: mt7925: prevent NULL pointer dereference in mt7925_sta_set_decap_offload() Add a NULL check for msta->vif before accessing its members to prevent a kernel panic in AP mode deployment. This also fix the issue reported in [1]. The crash occurs when this function is triggered before the station is fully initialized. The call trace shows a page fault at mt7925_sta_set_decap_offload() due to accessing resources when msta->vif is NULL. Fix this by adding an early return if msta->vif is NULL and also check wcid.sta is ready. This ensures we only proceed with decap offload configuration when the station's state is properly initialized. [14739.655703] Unable to handle kernel paging request at virtual address ffffffffffffffa0 [14739.811820] CPU: 0 UID: 0 PID: 895854 Comm: hostapd Tainted: G [14739.821394] Tainted: [C]=CRAP, [O]=OOT_MODULE [14739.825746] Hardware name: Raspberry Pi 4 Model B Rev 1.1 (DT) [14739.831577] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [14739.838538] pc : mt7925_sta_set_decap_offload+0xc0/0x1b8 [mt7925_common] [14739.845271] lr : mt7925_sta_set_decap_offload+0x58/0x1b8 [mt7925_common] [14739.851985] sp : ffffffc085efb500 [14739.855295] x29: ffffffc085efb500 x28: 0000000000000000 x27: ffffff807803a158 [14739.862436] x26: ffffff8041ececb8 x25: 0000000000000001 x24: 0000000000000001 [14739.869577] x23: 0000000000000001 x22: 0000000000000008 x21: ffffff8041ecea88 [14739.876715] x20: ffffff8041c19ca0 x19: ffffff8078031fe0 x18: 0000000000000000 [14739.883853] x17: 0000000000000000 x16: ffffffe2aeac1110 x15: 000000559da48080 [14739.890991] x14: 0000000000000001 x13: 0000000000000000 x12: 0000000000000000 [14739.898130] x11: 0a10020001008e88 x10: 0000000000001a50 x9 : ffffffe26457bfa0 [14739.905269] x8 : ffffff8042013bb0 x7 : ffffff807fb6cbf8 x6 : dead000000000100 [14739.912407] x5 : dead000000000122 x4 : ffffff80780326c8 x3 : 0000000000000000 [14739.919546] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffffff8041ececb8 [14739.926686] Call trace: [14739.929130] mt7925_sta_set_decap_offload+0xc0/0x1b8 [mt7925_common] [14739.935505] ieee80211_check_fast_rx+0x19c/0x510 [mac80211] [14739.941344] _sta_info_move_state+0xe4/0x510 [mac80211] [14739.946860] sta_info_move_state+0x1c/0x30 [mac80211] [14739.952116] sta_apply_auth_flags.constprop.0+0x90/0x1b0 [mac80211] [14739.958708] sta_apply_parameters+0x234/0x5e0 [mac80211] [14739.964332] ieee80211_add_station+0xdc/0x190 [mac80211] [14739.969950] nl80211_new_station+0x46c/0x670 [cfg80211] [14739.975516] genl_family_rcv_msg_doit+0xdc/0x150 [14739.980158] genl_rcv_msg+0x218/0x298 [14739.983830] netlink_rcv_skb+0x64/0x138 [14739.987670] genl_rcv+0x40/0x60 [14739.990816] netlink_unicast+0x314/0x380 [14739.994742] netlink_sendmsg+0x198/0x3f0 [14739.998664] __sock_sendmsg+0x64/0xc0 [14740.002324] ____sys_sendmsg+0x260/0x298 [14740.006242] ___sys_sendmsg+0xb4/0x110

In the Linux kernel, the following vulnerability has been resolved: riscv: save the SR_SUM status over switches When threads/tasks are switched we need to ensure the old execution's SR_SUM state is saved and the new thread has the old SR_SUM state restored. The issue was seen under heavy load especially with the syz-stress tool running, with crashes as follows in schedule_tail: Unable to handle kernel access to user memory without uaccess routines at virtual address 000000002749f0d0 Oops [#1] Modules linked in: CPU: 1 PID: 4875 Comm: syz-executor.0 Not tainted 5.12.0-rc2-syzkaller-00467-g0d7588ab9ef9 #0 Hardware name: riscv-virtio,qemu (DT) epc : schedule_tail+0x72/0xb2 kernel/sched/core.c:4264 ra : task_pid_vnr include/linux/sched.h:1421 [inline] ra : schedule_tail+0x70/0xb2 kernel/sched/core.c:4264 epc : ffffffe00008c8b0 ra : ffffffe00008c8ae sp : ffffffe025d17ec0 gp : ffffffe005d25378 tp : ffffffe00f0d0000 t0 : 0000000000000000 t1 : 0000000000000001 t2 : 00000000000f4240 s0 : ffffffe025d17ee0 s1 : 000000002749f0d0 a0 : 000000000000002a a1 : 0000000000000003 a2 : 1ffffffc0cfac500 a3 : ffffffe0000c80cc a4 : 5ae9db91c19bbe00 a5 : 0000000000000000 a6 : 0000000000f00000 a7 : ffffffe000082eba s2 : 0000000000040000 s3 : ffffffe00eef96c0 s4 : ffffffe022c77fe0 s5 : 0000000000004000 s6 : ffffffe067d74e00 s7 : ffffffe067d74850 s8 : ffffffe067d73e18 s9 : ffffffe067d74e00 s10: ffffffe00eef96e8 s11: 000000ae6cdf8368 t3 : 5ae9db91c19bbe00 t4 : ffffffc4043cafb2 t5 : ffffffc4043cafba t6 : 0000000000040000 status: 0000000000000120 badaddr: 000000002749f0d0 cause: 000000000000000f Call Trace: [<ffffffe00008c8b0>] schedule_tail+0x72/0xb2 kernel/sched/core.c:4264 [<ffffffe000005570>] ret_from_exception+0x0/0x14 Dumping ftrace buffer: (ftrace buffer empty) ---[ end trace b5f8f9231dc87dda ]--- The issue comes from the put_user() in schedule_tail (kernel/sched/core.c) doing the following: asmlinkage __visible void schedule_tail(struct task_struct *prev) { ... if (current->set_child_tid) put_user(task_pid_vnr(current), current->set_child_tid); ... } the put_user() macro causes the code sequence to come out as follows: 1: __enable_user_access() 2: reg = task_pid_vnr(current); 3: *current->set_child_tid = reg; 4: __disable_user_access() The problem is that we may have a sleeping function as argument which could clear SR_SUM causing the panic above. This was fixed by evaluating the argument of the put_user() macro outside the user-enabled section in commit 285a76bb2cf5 ("riscv: evaluate put_user() arg before enabling user access")" In order for riscv to take advantage of unsafe_get/put_XXX() macros and to avoid the same issue we had with put_user() and sleeping functions we must ensure code flow can go through switch_to() from within a region of code with SR_SUM enabled and come back with SR_SUM still enabled. This patch addresses the problem allowing future work to enable full use of unsafe_get/put_XXX() macros without needing to take a CSR bit flip cost on every access. Make switch_to() save and restore SR_SUM.

In the Linux kernel, the following vulnerability has been resolved: ice: Fix a null pointer dereference in ice_copy_and_init_pkg() Add check for the return value of devm_kmemdup() to prevent potential null pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Fix error flow upon firmware failure for RQ destruction Upon RQ destruction if the firmware command fails which is the last resource to be destroyed some SW resources were already cleaned regardless of the failure. Now properly rollback the object to its original state upon such failure. In order to avoid a use-after free in case someone tries to destroy the object again, which results in the following kernel trace: refcount_t: underflow; use-after-free. WARNING: CPU: 0 PID: 37589 at lib/refcount.c:28 refcount_warn_saturate+0xf4/0x148 Modules linked in: rdma_ucm(OE) rdma_cm(OE) iw_cm(OE) ib_ipoib(OE) ib_cm(OE) ib_umad(OE) mlx5_ib(OE) rfkill mlx5_core(OE) mlxdevm(OE) ib_uverbs(OE) ib_core(OE) psample mlxfw(OE) mlx_compat(OE) macsec tls pci_hyperv_intf sunrpc vfat fat virtio_net net_failover failover fuse loop nfnetlink vsock_loopback vmw_vsock_virtio_transport_common vmw_vsock_vmci_transport vmw_vmci vsock xfs crct10dif_ce ghash_ce sha2_ce sha256_arm64 sha1_ce virtio_console virtio_gpu virtio_blk virtio_dma_buf virtio_mmio dm_mirror dm_region_hash dm_log dm_mod xpmem(OE) CPU: 0 UID: 0 PID: 37589 Comm: python3 Kdump: loaded Tainted: G OE ------- --- 6.12.0-54.el10.aarch64 #1 Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : refcount_warn_saturate+0xf4/0x148 lr : refcount_warn_saturate+0xf4/0x148 sp : ffff80008b81b7e0 x29: ffff80008b81b7e0 x28: ffff000133d51600 x27: 0000000000000001 x26: 0000000000000000 x25: 00000000ffffffea x24: ffff00010ae80f00 x23: ffff00010ae80f80 x22: ffff0000c66e5d08 x21: 0000000000000000 x20: ffff0000c66e0000 x19: ffff00010ae80340 x18: 0000000000000006 x17: 0000000000000000 x16: 0000000000000020 x15: ffff80008b81b37f x14: 0000000000000000 x13: 2e656572662d7265 x12: ffff80008283ef78 x11: ffff80008257efd0 x10: ffff80008283efd0 x9 : ffff80008021ed90 x8 : 0000000000000001 x7 : 00000000000bffe8 x6 : c0000000ffff7fff x5 : ffff0001fb8e3408 x4 : 0000000000000000 x3 : ffff800179993000 x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000133d51600 Call trace: refcount_warn_saturate+0xf4/0x148 mlx5_core_put_rsc+0x88/0xa0 [mlx5_ib] mlx5_core_destroy_rq_tracked+0x64/0x98 [mlx5_ib] mlx5_ib_destroy_wq+0x34/0x80 [mlx5_ib] ib_destroy_wq_user+0x30/0xc0 [ib_core] uverbs_free_wq+0x28/0x58 [ib_uverbs] destroy_hw_idr_uobject+0x34/0x78 [ib_uverbs] uverbs_destroy_uobject+0x48/0x240 [ib_uverbs] __uverbs_cleanup_ufile+0xd4/0x1a8 [ib_uverbs] uverbs_destroy_ufile_hw+0x48/0x120 [ib_uverbs] ib_uverbs_close+0x2c/0x100 [ib_uverbs] __fput+0xd8/0x2f0 __fput_sync+0x50/0x70 __arm64_sys_close+0x40/0x90 invoke_syscall.constprop.0+0x74/0xd0 do_el0_svc+0x48/0xe8 el0_svc+0x44/0x1d0 el0t_64_sync_handler+0x120/0x130 el0t_64_sync+0x1a4/0x1a8

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix assertion when building free space tree When building the free space tree with the block group tree feature enabled, we can hit an assertion failure like this: BTRFS info (device loop0 state M): rebuilding free space tree assertion failed: ret == 0, in fs/btrfs/free-space-tree.c:1102 ------------[ cut here ]------------ kernel BUG at fs/btrfs/free-space-tree.c:1102! Internal error: Oops - BUG: 00000000f2000800 [#1] SMP Modules linked in: CPU: 1 UID: 0 PID: 6592 Comm: syz-executor322 Not tainted 6.15.0-rc7-syzkaller-gd7fa1af5b33e #0 PREEMPT Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025 pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : populate_free_space_tree+0x514/0x518 fs/btrfs/free-space-tree.c:1102 lr : populate_free_space_tree+0x514/0x518 fs/btrfs/free-space-tree.c:1102 sp : ffff8000a4ce7600 x29: ffff8000a4ce76e0 x28: ffff0000c9bc6000 x27: ffff0000ddfff3d8 x26: ffff0000ddfff378 x25: dfff800000000000 x24: 0000000000000001 x23: ffff8000a4ce7660 x22: ffff70001499cecc x21: ffff0000e1d8c160 x20: ffff0000e1cb7800 x19: ffff0000e1d8c0b0 x18: 00000000ffffffff x17: ffff800092f39000 x16: ffff80008ad27e48 x15: ffff700011e740c0 x14: 1ffff00011e740c0 x13: 0000000000000004 x12: ffffffffffffffff x11: ffff700011e740c0 x10: 0000000000ff0100 x9 : 94ef24f55d2dbc00 x8 : 94ef24f55d2dbc00 x7 : 0000000000000001 x6 : 0000000000000001 x5 : ffff8000a4ce6f98 x4 : ffff80008f415ba0 x3 : ffff800080548ef0 x2 : 0000000000000000 x1 : 0000000100000000 x0 : 000000000000003e Call trace: populate_free_space_tree+0x514/0x518 fs/btrfs/free-space-tree.c:1102 (P) btrfs_rebuild_free_space_tree+0x14c/0x54c fs/btrfs/free-space-tree.c:1337 btrfs_start_pre_rw_mount+0xa78/0xe10 fs/btrfs/disk-io.c:3074 btrfs_remount_rw fs/btrfs/super.c:1319 [inline] btrfs_reconfigure+0x828/0x2418 fs/btrfs/super.c:1543 reconfigure_super+0x1d4/0x6f0 fs/super.c:1083 do_remount fs/namespace.c:3365 [inline] path_mount+0xb34/0xde0 fs/namespace.c:4200 do_mount fs/namespace.c:4221 [inline] __do_sys_mount fs/namespace.c:4432 [inline] __se_sys_mount fs/namespace.c:4409 [inline] __arm64_sys_mount+0x3e8/0x468 fs/namespace.c:4409 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132 do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151 el0_svc+0x58/0x17c arch/arm64/kernel/entry-common.c:767 el0t_64_sync_handler+0x78/0x108 arch/arm64/kernel/entry-common.c:786 el0t_64_sync+0x198/0x19c arch/arm64/kernel/entry.S:600 Code: f0047182 91178042 528089c3 9771d47b (d4210000) ---[ end trace 0000000000000000 ]--- This happens because we are processing an empty block group, which has no extents allocated from it, there are no items for this block group, including the block group item since block group items are stored in a dedicated tree when using the block group tree feature. It also means this is the block group with the highest start offset, so there are no higher keys in the extent root, hence btrfs_search_slot_for_read() returns 1 (no higher key found). Fix this by asserting 'ret' is 0 only if the block group tree feature is not enabled, in which case we should find a block group item for the block group since it's stored in the extent root and block group item keys are greater than extent item keys (the value for BTRFS_BLOCK_GROUP_ITEM_KEY is 192 and for BTRFS_EXTENT_ITEM_KEY and BTRFS_METADATA_ITEM_KEY the values are 168 and 169 respectively). In case 'ret' is 1, we just need to add a record to the free space tree which spans the whole block group, and we can achieve this by making 'ret == 0' as the while loop's condition.

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix the inode leak in btrfs_iget() [BUG] There is a bug report that a syzbot reproducer can lead to the following busy inode at unmount time: BTRFS info (device loop1): last unmount of filesystem 1680000e-3c1e-4c46-84b6-56bd3909af50 VFS: Busy inodes after unmount of loop1 (btrfs) ------------[ cut here ]------------ kernel BUG at fs/super.c:650! Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI CPU: 0 UID: 0 PID: 48168 Comm: syz-executor Not tainted 6.15.0-rc2-00471-g119009db2674 #2 PREEMPT(full) Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:generic_shutdown_super+0x2e9/0x390 fs/super.c:650 Call Trace: <TASK> kill_anon_super+0x3a/0x60 fs/super.c:1237 btrfs_kill_super+0x3b/0x50 fs/btrfs/super.c:2099 deactivate_locked_super+0xbe/0x1a0 fs/super.c:473 deactivate_super fs/super.c:506 [inline] deactivate_super+0xe2/0x100 fs/super.c:502 cleanup_mnt+0x21f/0x440 fs/namespace.c:1435 task_work_run+0x14d/0x240 kernel/task_work.c:227 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] exit_to_user_mode_loop kernel/entry/common.c:114 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x269/0x290 kernel/entry/common.c:218 do_syscall_64+0xd4/0x250 arch/x86/entry/syscall_64.c:100 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> [CAUSE] When btrfs_alloc_path() failed, btrfs_iget() directly returned without releasing the inode already allocated by btrfs_iget_locked(). This results the above busy inode and trigger the kernel BUG. [FIX] Fix it by calling iget_failed() if btrfs_alloc_path() failed. If we hit error inside btrfs_read_locked_inode(), it will properly call iget_failed(), so nothing to worry about. Although the iget_failed() cleanup inside btrfs_read_locked_inode() is a break of the normal error handling scheme, let's fix the obvious bug and backport first, then rework the error handling later.

In the Linux kernel, the following vulnerability has been resolved: io_uring/zcrx: fix pp destruction warnings With multiple page pools and in some other cases we can have allocated niovs on page pool destruction. Remove a misplaced warning checking that all niovs are returned to zcrx on io_pp_zc_destroy(). It was reported before but apparently got lost.

In the Linux kernel, the following vulnerability has been resolved: net/tls: fix kernel panic when alloc_page failed We cannot set frag_list to NULL pointer when alloc_page failed. It will be used in tls_strp_check_queue_ok when the next time tls_strp_read_sock is called. This is because we don't reset full_len in tls_strp_flush_anchor_copy() so the recv path will try to continue handling the partial record on the next call but we dettached the rcvq from the frag list. Alternative fix would be to reset full_len. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000028 Call trace: tls_strp_check_rcv+0x128/0x27c tls_strp_data_ready+0x34/0x44 tls_data_ready+0x3c/0x1f0 tcp_data_ready+0x9c/0xe4 tcp_data_queue+0xf6c/0x12d0 tcp_rcv_established+0x52c/0x798

In the Linux kernel, the following vulnerability has been resolved: mm/damon: fix divide by zero in damon_get_intervals_score() The current implementation allows having zero size regions with no special reasons, but damon_get_intervals_score() gets crashed by divide by zero when the region size is zero. [ 29.403950] Oops: divide error: 0000 [#1] SMP NOPTI This patch fixes the bug, but does not disallow zero size regions to keep the backward compatibility since disallowing zero size regions might be a breaking change for some users. In addition, the same crash can happen when intervals_goal.access_bp is zero so this should be fixed in stable trees as well.

In the Linux kernel, the following vulnerability has been resolved: fs/dax: Fix "don't skip locked entries when scanning entries" Commit 6be3e21d25ca ("fs/dax: don't skip locked entries when scanning entries") introduced a new function, wait_entry_unlocked_exclusive(), which waits for the current entry to become unlocked without advancing the XArray iterator state. Waiting for the entry to become unlocked requires dropping the XArray lock. This requires calling xas_pause() prior to dropping the lock which leaves the xas in a suitable state for the next iteration. However this has the side-effect of advancing the xas state to the next index. Normally this isn't an issue because xas_for_each() contains code to detect this state and thus avoid advancing the index a second time on the next loop iteration. However both callers of and wait_entry_unlocked_exclusive() itself subsequently use the xas state to reload the entry. As xas_pause() updated the state to the next index this will cause the current entry which is being waited on to be skipped. This caused the following warning to fire intermittently when running xftest generic/068 on an XFS filesystem with FS DAX enabled: [ 35.067397] ------------[ cut here ]------------ [ 35.068229] WARNING: CPU: 21 PID: 1640 at mm/truncate.c:89 truncate_folio_batch_exceptionals+0xd8/0x1e0 [ 35.069717] Modules linked in: nd_pmem dax_pmem nd_btt nd_e820 libnvdimm [ 35.071006] CPU: 21 UID: 0 PID: 1640 Comm: fstest Not tainted 6.15.0-rc7+ #77 PREEMPT(voluntary) [ 35.072613] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/204 [ 35.074845] RIP: 0010:truncate_folio_batch_exceptionals+0xd8/0x1e0 [ 35.075962] Code: a1 00 00 00 f6 47 0d 20 0f 84 97 00 00 00 4c 63 e8 41 39 c4 7f 0b eb 61 49 83 c5 01 45 39 ec 7e 58 42 f68 [ 35.079522] RSP: 0018:ffffb04e426c7850 EFLAGS: 00010202 [ 35.080359] RAX: 0000000000000000 RBX: ffff9d21e3481908 RCX: ffffb04e426c77f4 [ 35.081477] RDX: ffffb04e426c79e8 RSI: ffffb04e426c79e0 RDI: ffff9d21e34816e8 [ 35.082590] RBP: ffffb04e426c79e0 R08: 0000000000000001 R09: 0000000000000003 [ 35.083733] R10: 0000000000000000 R11: 822b53c0f7a49868 R12: 000000000000001f [ 35.084850] R13: 0000000000000000 R14: ffffb04e426c78e8 R15: fffffffffffffffe [ 35.085953] FS: 00007f9134c87740(0000) GS:ffff9d22abba0000(0000) knlGS:0000000000000000 [ 35.087346] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 35.088244] CR2: 00007f9134c86000 CR3: 000000040afff000 CR4: 00000000000006f0 [ 35.089354] Call Trace: [ 35.089749] <TASK> [ 35.090168] truncate_inode_pages_range+0xfc/0x4d0 [ 35.091078] truncate_pagecache+0x47/0x60 [ 35.091735] xfs_setattr_size+0xc7/0x3e0 [ 35.092648] xfs_vn_setattr+0x1ea/0x270 [ 35.093437] notify_change+0x1f4/0x510 [ 35.094219] ? do_truncate+0x97/0xe0 [ 35.094879] do_truncate+0x97/0xe0 [ 35.095640] path_openat+0xabd/0xca0 [ 35.096278] do_filp_open+0xd7/0x190 [ 35.096860] do_sys_openat2+0x8a/0xe0 [ 35.097459] __x64_sys_openat+0x6d/0xa0 [ 35.098076] do_syscall_64+0xbb/0x1d0 [ 35.098647] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 35.099444] RIP: 0033:0x7f9134d81fc1 [ 35.100033] Code: 75 57 89 f0 25 00 00 41 00 3d 00 00 41 00 74 49 80 3d 2a 26 0e 00 00 74 6d 89 da 48 89 ee bf 9c ff ff ff5 [ 35.102993] RSP: 002b:00007ffcd41e0d10 EFLAGS: 00000202 ORIG_RAX: 0000000000000101 [ 35.104263] RAX: ffffffffffffffda RBX: 0000000000000242 RCX: 00007f9134d81fc1 [ 35.105452] RDX: 0000000000000242 RSI: 00007ffcd41e1200 RDI: 00000000ffffff9c [ 35.106663] RBP: 00007ffcd41e1200 R08: 0000000000000000 R09: 0000000000000064 [ 35.107923] R10: 00000000000001a4 R11: 0000000000000202 R12: 0000000000000066 [ 35.109112] R13: 0000000000100000 R14: 0000000000100000 R15: 0000000000000400 [ 35.110357] </TASK> [ 35.110769] irq event stamp: 8415587 [ 35.111486] hardirqs last enabled at (8415599): [<ffffffff8d74b562>] __up_console_se ---truncated---

In the Linux kernel, the following vulnerability has been resolved: mm/shmem, swap: fix softlockup with mTHP swapin Following softlockup can be easily reproduced on my test machine with: echo always > /sys/kernel/mm/transparent_hugepage/hugepages-64kB/enabled swapon /dev/zram0 # zram0 is a 48G swap device mkdir -p /sys/fs/cgroup/memory/test echo 1G > /sys/fs/cgroup/test/memory.max echo $BASHPID > /sys/fs/cgroup/test/cgroup.procs while true; do dd if=/dev/zero of=/tmp/test.img bs=1M count=5120 cat /tmp/test.img > /dev/null rm /tmp/test.img done Then after a while: watchdog: BUG: soft lockup - CPU#0 stuck for 763s! [cat:5787] Modules linked in: zram virtiofs CPU: 0 UID: 0 PID: 5787 Comm: cat Kdump: loaded Tainted: G L 6.15.0.orig-gf3021d9246bc-dirty #118 PREEMPT(voluntary)· Tainted: [L]=SOFTLOCKUP Hardware name: Red Hat KVM/RHEL-AV, BIOS 0.0.0 02/06/2015 RIP: 0010:mpol_shared_policy_lookup+0xd/0x70 Code: e9 b8 b4 ff ff 31 c0 c3 cc cc cc cc 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 66 0f 1f 00 0f 1f 44 00 00 41 54 55 53 <48> 8b 1f 48 85 db 74 41 4c 8d 67 08 48 89 fb 48 89 f5 4c 89 e7 e8 RSP: 0018:ffffc90002b1fc28 EFLAGS: 00000202 RAX: 00000000001c20ca RBX: 0000000000724e1e RCX: 0000000000000001 RDX: ffff888118e214c8 RSI: 0000000000057d42 RDI: ffff888118e21518 RBP: 000000000002bec8 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000bf4 R11: 0000000000000000 R12: 0000000000000001 R13: 00000000001c20ca R14: 00000000001c20ca R15: 0000000000000000 FS: 00007f03f995c740(0000) GS:ffff88a07ad9a000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f03f98f1000 CR3: 0000000144626004 CR4: 0000000000770eb0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> shmem_alloc_folio+0x31/0xc0 shmem_swapin_folio+0x309/0xcf0 ? filemap_get_entry+0x117/0x1e0 ? xas_load+0xd/0xb0 ? filemap_get_entry+0x101/0x1e0 shmem_get_folio_gfp+0x2ed/0x5b0 shmem_file_read_iter+0x7f/0x2e0 vfs_read+0x252/0x330 ksys_read+0x68/0xf0 do_syscall_64+0x4c/0x1c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f03f9a46991 Code: 00 48 8b 15 81 14 10 00 f7 d8 64 89 02 b8 ff ff ff ff eb bd e8 20 ad 01 00 f3 0f 1e fa 80 3d 35 97 10 00 00 74 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 4f c3 66 0f 1f 44 00 00 55 48 89 e5 48 83 ec RSP: 002b:00007fff3c52bd28 EFLAGS: 00000246 ORIG_RAX: 0000000000000000 RAX: ffffffffffffffda RBX: 0000000000040000 RCX: 00007f03f9a46991 RDX: 0000000000040000 RSI: 00007f03f98ba000 RDI: 0000000000000003 RBP: 00007fff3c52bd50 R08: 0000000000000000 R09: 00007f03f9b9a380 R10: 0000000000000022 R11: 0000000000000246 R12: 0000000000040000 R13: 00007f03f98ba000 R14: 0000000000000003 R15: 0000000000000000 </TASK> The reason is simple, readahead brought some order 0 folio in swap cache, and the swapin mTHP folio being allocated is in conflict with it, so swapcache_prepare fails and causes shmem_swap_alloc_folio to return -EEXIST, and shmem simply retries again and again causing this loop. Fix it by applying a similar fix for anon mTHP swapin. The performance change is very slight, time of swapin 10g zero folios with shmem (test for 12 times): Before: 2.47s After: 2.48s [kasong@tencent.com: add comment]

In the Linux kernel, the following vulnerability has been resolved: can: netlink: can_changelink(): fix NULL pointer deref of struct can_priv::do_set_mode Andrei Lalaev reported a NULL pointer deref when a CAN device is restarted from Bus Off and the driver does not implement the struct can_priv::do_set_mode callback. There are 2 code path that call struct can_priv::do_set_mode: - directly by a manual restart from the user space, via can_changelink() - delayed automatic restart after bus off (deactivated by default) To prevent the NULL pointer deference, refuse a manual restart or configure the automatic restart delay in can_changelink() and report the error via extack to user space. As an additional safety measure let can_restart() return an error if can_priv::do_set_mode is not set instead of dereferencing it unchecked.

In the Linux kernel, the following vulnerability has been resolved: media: cx231xx: set device_caps for 417 The video_device for the MPEG encoder did not set device_caps. Add this, otherwise the video device can't be registered (you get a WARN_ON instead). Not seen before since currently 417 support is disabled, but I found this while experimenting with it.

In the Linux kernel, the following vulnerability has been resolved: objtool, media: dib8000: Prevent divide-by-zero in dib8000_set_dds() If dib8000_set_dds()'s call to dib8000_read32() returns zero, the result is a divide-by-zero. Prevent that from happening. Fixes the following warning with an UBSAN kernel: drivers/media/dvb-frontends/dib8000.o: warning: objtool: dib8000_tune() falls through to next function dib8096p_cfg_DibRx()

In the Linux kernel, the following vulnerability has been resolved: crypto: ccp - Fix crash when rebind ccp device for ccp.ko When CONFIG_CRYPTO_DEV_CCP_DEBUGFS is enabled, rebinding the ccp device causes the following crash: $ echo '0000:0a:00.2' > /sys/bus/pci/drivers/ccp/unbind $ echo '0000:0a:00.2' > /sys/bus/pci/drivers/ccp/bind [ 204.976930] BUG: kernel NULL pointer dereference, address: 0000000000000098 [ 204.978026] #PF: supervisor write access in kernel mode [ 204.979126] #PF: error_code(0x0002) - not-present page [ 204.980226] PGD 0 P4D 0 [ 204.981317] Oops: Oops: 0002 [#1] SMP NOPTI ... [ 204.997852] Call Trace: [ 204.999074] <TASK> [ 205.000297] start_creating+0x9f/0x1c0 [ 205.001533] debugfs_create_dir+0x1f/0x170 [ 205.002769] ? srso_return_thunk+0x5/0x5f [ 205.004000] ccp5_debugfs_setup+0x87/0x170 [ccp] [ 205.005241] ccp5_init+0x8b2/0x960 [ccp] [ 205.006469] ccp_dev_init+0xd4/0x150 [ccp] [ 205.007709] sp_init+0x5f/0x80 [ccp] [ 205.008942] sp_pci_probe+0x283/0x2e0 [ccp] [ 205.010165] ? srso_return_thunk+0x5/0x5f [ 205.011376] local_pci_probe+0x4f/0xb0 [ 205.012584] pci_device_probe+0xdb/0x230 [ 205.013810] really_probe+0xed/0x380 [ 205.015024] __driver_probe_device+0x7e/0x160 [ 205.016240] device_driver_attach+0x2f/0x60 [ 205.017457] bind_store+0x7c/0xb0 [ 205.018663] drv_attr_store+0x28/0x40 [ 205.019868] sysfs_kf_write+0x5f/0x70 [ 205.021065] kernfs_fop_write_iter+0x145/0x1d0 [ 205.022267] vfs_write+0x308/0x440 [ 205.023453] ksys_write+0x6d/0xe0 [ 205.024616] __x64_sys_write+0x1e/0x30 [ 205.025778] x64_sys_call+0x16ba/0x2150 [ 205.026942] do_syscall_64+0x56/0x1e0 [ 205.028108] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 205.029276] RIP: 0033:0x7fbc36f10104 [ 205.030420] Code: 89 02 48 c7 c0 ff ff ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 8d 05 e1 08 2e 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 f3 c3 66 90 41 54 55 49 89 d4 53 48 89 f5 This patch sets ccp_debugfs_dir to NULL after destroying it in ccp5_debugfs_destroy, allowing the directory dentry to be recreated when rebinding the ccp device. Tested on AMD Ryzen 7 1700X.

In the Linux kernel, the following vulnerability has been resolved: perf: arm-ni: Unregister PMUs on probe failure When a resource allocation fails in one clock domain of an NI device, we need to properly roll back all previously registered perf PMUs in other clock domains of the same device. Otherwise, it can lead to kernel panics. Calling arm_ni_init+0x0/0xff8 [arm_ni] @ 2374 arm-ni ARMHCB70:00: Failed to request PMU region 0x1f3c13000 arm-ni ARMHCB70:00: probe with driver arm-ni failed with error -16 list_add corruption: next->prev should be prev (fffffd01e9698a18), but was 0000000000000000. (next=ffff10001a0decc8). pstate: 6340009 (nZCv daif +PAN -UAO +TCO +DIT -SSBS BTYPE=--) pc : list_add_valid_or_report+0x7c/0xb8 lr : list_add_valid_or_report+0x7c/0xb8 Call trace: __list_add_valid_or_report+0x7c/0xb8 perf_pmu_register+0x22c/0x3a0 arm_ni_probe+0x554/0x70c [arm_ni] platform_probe+0x70/0xe8 really_probe+0xc6/0x4d8 driver_probe_device+0x48/0x170 __driver_attach+0x8e/0x1c0 bus_for_each_dev+0x64/0xf0 driver_add+0x138/0x260 bus_add_driver+0x68/0x138 __platform_driver_register+0x2c/0x40 arm_ni_init+0x14/0x2a [arm_ni] do_init_module+0x36/0x298 ---[ end trace 0000000000000000 ]--- Kernel panic - not syncing: Oops - BUG: Fatal exception SMP: stopping secondary CPUs

In the Linux kernel, the following vulnerability has been resolved: pinctrl: qcom: msm: mark certain pins as invalid for interrupts On some platforms, the UFS-reset pin has no interrupt logic in TLMM but is nevertheless registered as a GPIO in the kernel. This enables the user-space to trigger a BUG() in the pinctrl-msm driver by running, for example: `gpiomon -c 0 113` on RB2. The exact culprit is requesting pins whose intr_detection_width setting is not 1 or 2 for interrupts. This hits a BUG() in msm_gpio_irq_set_type(). Potentially crashing the kernel due to an invalid request from user-space is not optimal, so let's go through the pins and mark those that would fail the check as invalid for the irq chip as we should not even register them as available irqs. This function can be extended if we determine that there are more corner-cases like this.

In the Linux kernel, the following vulnerability has been resolved: idpf: fix null-ptr-deref in idpf_features_check idpf_features_check is used to validate the TX packet. skb header length is compared with the hardware supported value received from the device control plane. The value is stored in the adapter structure and to access it, vport pointer is used. During reset all the vports are released and the vport pointer that the netdev private structure points to is NULL. To avoid null-ptr-deref, store the max header length value in netdev private structure. This also helps to cache the value and avoid accessing adapter pointer in hot path. BUG: kernel NULL pointer dereference, address: 0000000000000068 ... RIP: 0010:idpf_features_check+0x6d/0xe0 [idpf] Call Trace: <TASK> ? __die+0x23/0x70 ? page_fault_oops+0x154/0x520 ? exc_page_fault+0x76/0x190 ? asm_exc_page_fault+0x26/0x30 ? idpf_features_check+0x6d/0xe0 [idpf] netif_skb_features+0x88/0x310 validate_xmit_skb+0x2a/0x2b0 validate_xmit_skb_list+0x4c/0x70 sch_direct_xmit+0x19d/0x3a0 __dev_queue_xmit+0xb74/0xe70 ...

In the Linux kernel, the following vulnerability has been resolved: ftrace: Add cond_resched() to ftrace_graph_set_hash() When the kernel contains a large number of functions that can be traced, the loop in ftrace_graph_set_hash() may take a lot of time to execute. This may trigger the softlockup watchdog. Add cond_resched() within the loop to allow the kernel to remain responsive even when processing a large number of functions. This matches the cond_resched() that is used in other locations of the code that iterates over all functions that can be traced.