In the Linux kernel, the following vulnerability has been resolved: audit: fix out-of-bounds read in audit_compare_dname_path() When a watch on dir=/ is combined with an fsnotify event for a single-character name directly under / (e.g., creating /a), an out-of-bounds read can occur in audit_compare_dname_path(). The helper parent_len() returns 1 for "/". In audit_compare_dname_path(), when parentlen equals the full path length (1), the code sets p = path + 1 and pathlen = 1 - 1 = 0. The subsequent loop then dereferences p[pathlen - 1] (i.e., p[-1]), causing an out-of-bounds read. Fix this by adding a pathlen > 0 check to the while loop condition to prevent the out-of-bounds access. [PM: subject tweak, sign-off email fixes]

In the Linux kernel, the following vulnerability has been resolved: dmaengine: ti: edma: Fix memory allocation size for queue_priority_map Fix a critical memory allocation bug in edma_setup_from_hw() where queue_priority_map was allocated with insufficient memory. The code declared queue_priority_map as s8 (*)[2] (pointer to array of 2 s8), but allocated memory using sizeof(s8) instead of the correct size. This caused out-of-bounds memory writes when accessing: queue_priority_map[i][0] = i; queue_priority_map[i][1] = i; The bug manifested as kernel crashes with "Oops - undefined instruction" on ARM platforms (BeagleBoard-X15) during EDMA driver probe, as the memory corruption triggered kernel hardening features on Clang. Change the allocation to use sizeof(*queue_priority_map) which automatically gets the correct size for the 2D array structure.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid out-of-boundary access in devs.path - touch /mnt/f2fs/012345678901234567890123456789012345678901234567890123 - truncate -s $((1024*1024*1024)) \ /mnt/f2fs/012345678901234567890123456789012345678901234567890123 - touch /mnt/f2fs/file - truncate -s $((1024*1024*1024)) /mnt/f2fs/file - mkfs.f2fs /mnt/f2fs/012345678901234567890123456789012345678901234567890123 \ -c /mnt/f2fs/file - mount /mnt/f2fs/012345678901234567890123456789012345678901234567890123 \ /mnt/f2fs/loop [16937.192225] F2FS-fs (loop0): Mount Device [ 0]: /mnt/f2fs/012345678901234567890123456789012345678901234567890123\xff\x01, 511, 0 - 3ffff [16937.192268] F2FS-fs (loop0): Failed to find devices If device path length equals to MAX_PATH_LEN, sbi->devs.path[] may not end up w/ null character due to path array is fully filled, So accidently, fields locate after path[] may be treated as part of device path, result in parsing wrong device path. struct f2fs_dev_info { ... char path[MAX_PATH_LEN]; ... }; Let's add one byte space for sbi->devs.path[] to store null character of device path string.

In the Linux kernel, the following vulnerability has been resolved: tls: handle data disappearing from under the TLS ULP TLS expects that it owns the receive queue of the TCP socket. This cannot be guaranteed in case the reader of the TCP socket entered before the TLS ULP was installed, or uses some non-standard read API (eg. zerocopy ones). Replace the WARN_ON() and a buggy early exit (which leaves anchor pointing to a freed skb) with real error handling. Wipe the parsing state and tell the reader to retry. We already reload the anchor every time we (re)acquire the socket lock, so the only condition we need to avoid is an out of bounds read (not having enough bytes in the socket for previously parsed record len). If some data was read from under TLS but there's enough in the queue we'll reload and decrypt what is most likely not a valid TLS record. Leading to some undefined behavior from TLS perspective (corrupting a stream? missing an alert? missing an attack?) but no kernel crash should take place.

In the Linux kernel, the following vulnerability has been resolved: hfs: fix slab-out-of-bounds in hfs_bnode_read() This patch introduces is_bnode_offset_valid() method that checks the requested offset value. Also, it introduces check_and_correct_requested_length() method that checks and correct the requested length (if it is necessary). These methods are used in hfs_bnode_read(), hfs_bnode_write(), hfs_bnode_clear(), hfs_bnode_copy(), and hfs_bnode_move() with the goal to prevent the access out of allocated memory and triggering the crash.

In the Linux kernel, the following vulnerability has been resolved: net: usb: asix_devices: Fix PHY address mask in MDIO bus initialization Syzbot reported shift-out-of-bounds exception on MDIO bus initialization. The PHY address should be masked to 5 bits (0-31). Without this mask, invalid PHY addresses could be used, potentially causing issues with MDIO bus operations. Fix this by masking the PHY address with 0x1f (31 decimal) to ensure it stays within the valid range.

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix 1-byte out-of-bounds read in uvc_parse_format() The buffer length check before calling uvc_parse_format() only ensured that the buffer has at least 3 bytes (buflen > 2), buf the function accesses buffer[3], requiring at least 4 bytes. This can lead to an out-of-bounds read if the buffer has exactly 3 bytes. Fix it by checking that the buffer has at least 4 bytes in uvc_parse_format().

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: Decrement TID on RX peer frag setup error handling Currently, TID is not decremented before peer cleanup, during error handling path of ath12k_dp_rx_peer_frag_setup(). This could lead to out-of-bounds access in peer->rx_tid[]. Hence, add a decrement operation for TID, before peer cleanup to ensures proper cleanup and prevents out-of-bounds access issues when the RX peer frag setup fails. Found during code review. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: iio: imu: bno055: fix OOB access of hw_xlate array Fix a potential out-of-bounds array access of the hw_xlate array in bno055.c. In bno055_get_regmask(), hw_xlate was iterated over the length of the vals array instead of the length of the hw_xlate array. In the case of bno055_gyr_scale, the vals array is larger than the hw_xlate array, so this could result in an out-of-bounds access. In practice, this shouldn't happen though because a match should always be found which breaks out of the for loop before it iterates beyond the end of the hw_xlate array. By adding a new hw_xlate_len field to the bno055_sysfs_attr, we can be sure we are iterating over the correct length.

In the Linux kernel, the following vulnerability has been resolved: i2c: rtl9300: Fix out-of-bounds bug in rtl9300_i2c_smbus_xfer The data->block[0] variable comes from user. Without proper check, the variable may be very large to cause an out-of-bounds bug. Fix this bug by checking the value of data->block[0] first. 1. commit 39244cc75482 ("i2c: ismt: Fix an out-of-bounds bug in ismt_access()") 2. commit 92fbb6d1296f ("i2c: xgene-slimpro: Fix out-of-bounds bug in xgene_slimpro_i2c_xfer()")

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix oob access in cgroup local storage Lonial reported that an out-of-bounds access in cgroup local storage can be crafted via tail calls. Given two programs each utilizing a cgroup local storage with a different value size, and one program doing a tail call into the other. The verifier will validate each of the indivial programs just fine. However, in the runtime context the bpf_cg_run_ctx holds an bpf_prog_array_item which contains the BPF program as well as any cgroup local storage flavor the program uses. Helpers such as bpf_get_local_storage() pick this up from the runtime context: ctx = container_of(current->bpf_ctx, struct bpf_cg_run_ctx, run_ctx); storage = ctx->prog_item->cgroup_storage[stype]; if (stype == BPF_CGROUP_STORAGE_SHARED) ptr = &READ_ONCE(storage->buf)->data[0]; else ptr = this_cpu_ptr(storage->percpu_buf); For the second program which was called from the originally attached one, this means bpf_get_local_storage() will pick up the former program's map, not its own. With mismatching sizes, this can result in an unintended out-of-bounds access. To fix this issue, we need to extend bpf_map_owner with an array of storage_cookie[] to match on i) the exact maps from the original program if the second program was using bpf_get_local_storage(), or ii) allow the tail call combination if the second program was not using any of the cgroup local storage maps.

In the Linux kernel, the following vulnerability has been resolved: regulator: max20086: fix invalid memory access max20086_parse_regulators_dt() calls of_regulator_match() using an array of struct of_regulator_match allocated on the stack for the matches argument. of_regulator_match() calls devm_of_regulator_put_matches(), which calls devres_alloc() to allocate a struct devm_of_regulator_matches which will be de-allocated using devm_of_regulator_put_matches(). struct devm_of_regulator_matches is populated with the stack allocated matches array. If the device fails to probe, devm_of_regulator_put_matches() will be called and will try to call of_node_put() on that stack pointer, generating the following dmesg entries: max20086 6-0028: Failed to read DEVICE_ID reg: -121 kobject: '\xc0$\xa5\x03' (000000002cebcb7a): is not initialized, yet kobject_put() is being called. Followed by a stack trace matching the call flow described above. Switch to allocating the matches array using devm_kcalloc() to avoid accessing the stack pointer long after it's out of scope. This also has the advantage of allowing multiple max20086 to probe without overriding the data stored inside the global of_regulator_match.

In the Linux kernel, the following vulnerability has been resolved: HID: core: Harden s32ton() against conversion to 0 bits Testing by the syzbot fuzzer showed that the HID core gets a shift-out-of-bounds exception when it tries to convert a 32-bit quantity to a 0-bit quantity. Ideally this should never occur, but there are buggy devices and some might have a report field with size set to zero; we shouldn't reject the report or the device just because of that. Instead, harden the s32ton() routine so that it returns a reasonable result instead of crashing when it is called with the number of bits set to 0 -- the same as what snto32() does.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: fix out-of-bounds access during multi-link element defragmentation Currently during the multi-link element defragmentation process, the multi-link element length added to the total IEs length when calculating the length of remaining IEs after the multi-link element in cfg80211_defrag_mle(). This could lead to out-of-bounds access if the multi-link element or its corresponding fragment elements are the last elements in the IEs buffer. To address this issue, correctly calculate the remaining IEs length by deducting the multi-link element end offset from total IEs end offset.

In the Linux kernel, the following vulnerability has been resolved: ext4: fix out of bounds punch offset Punching a hole with a start offset that exceeds max_end is not permitted and will result in a negative length in the truncate_inode_partial_folio() function while truncating the page cache, potentially leading to undesirable consequences. A simple reproducer: truncate -s 9895604649994 /mnt/foo xfs_io -c "pwrite 8796093022208 4096" /mnt/foo xfs_io -c "fpunch 8796093022213 25769803777" /mnt/foo kernel BUG at include/linux/highmem.h:275! Oops: invalid opcode: 0000 [#1] SMP PTI CPU: 3 UID: 0 PID: 710 Comm: xfs_io Not tainted 6.15.0-rc3 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:zero_user_segments.constprop.0+0xd7/0x110 RSP: 0018:ffffc90001cf3b38 EFLAGS: 00010287 RAX: 0000000000000005 RBX: ffffea0001485e40 RCX: 0000000000001000 RDX: 000000000040b000 RSI: 0000000000000005 RDI: 000000000040b000 RBP: 000000000040affb R08: ffff888000000000 R09: ffffea0000000000 R10: 0000000000000003 R11: 00000000fffc7fc5 R12: 0000000000000005 R13: 000000000040affb R14: ffffea0001485e40 R15: ffff888031cd3000 FS: 00007f4f63d0b780(0000) GS:ffff8880d337d000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000001ae0b038 CR3: 00000000536aa000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> truncate_inode_partial_folio+0x3dd/0x620 truncate_inode_pages_range+0x226/0x720 ? bdev_getblk+0x52/0x3e0 ? ext4_get_group_desc+0x78/0x150 ? crc32c_arch+0xfd/0x180 ? __ext4_get_inode_loc+0x18c/0x840 ? ext4_inode_csum+0x117/0x160 ? jbd2_journal_dirty_metadata+0x61/0x390 ? __ext4_handle_dirty_metadata+0xa0/0x2b0 ? kmem_cache_free+0x90/0x5a0 ? jbd2_journal_stop+0x1d5/0x550 ? __ext4_journal_stop+0x49/0x100 truncate_pagecache_range+0x50/0x80 ext4_truncate_page_cache_block_range+0x57/0x3a0 ext4_punch_hole+0x1fe/0x670 ext4_fallocate+0x792/0x17d0 ? __count_memcg_events+0x175/0x2a0 vfs_fallocate+0x121/0x560 ksys_fallocate+0x51/0xc0 __x64_sys_fallocate+0x24/0x40 x64_sys_call+0x18d2/0x4170 do_syscall_64+0xa7/0x220 entry_SYSCALL_64_after_hwframe+0x76/0x7e Fix this by filtering out cases where the punching start offset exceeds max_end.

In the Linux kernel, the following vulnerability has been resolved: spi-rockchip: Fix register out of bounds access Do not write native chip select stuff for GPIO chip selects. GPIOs can be numbered much higher than native CS. Also, it makes no sense.

In the Linux kernel, the following vulnerability has been resolved: net/mdiobus: Fix potential out-of-bounds clause 45 read/write access When using publicly available tools like 'mdio-tools' to read/write data from/to network interface and its PHY via C45 (clause 45) mdiobus, there is no verification of parameters passed to the ioctl and it accepts any mdio address. Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define, but it is possible to pass higher value than that via ioctl. While read/write operation should generally fail in this case, mdiobus provides stats array, where wrong address may allow out-of-bounds read/write. Fix that by adding address verification before C45 read/write operation. While this excludes this access from any statistics, it improves security of read/write operation.

In the Linux kernel, the following vulnerability has been resolved: comedi: pcl812: Fix bit shift out of bounds When checking for a supported IRQ number, the following test is used: if ((1 << it->options[1]) & board->irq_bits) { However, `it->options[i]` is an unchecked `int` value from userspace, so the shift amount could be negative or out of bounds. Fix the test by requiring `it->options[1]` to be within bounds before proceeding with the original test. Valid `it->options[1]` values that select the IRQ will be in the range [1,15]. The value 0 explicitly disables the use of interrupts.

In the Linux kernel, the following vulnerability has been resolved: 9p/net: fix improper handling of bogus negative read/write replies In p9_client_write() and p9_client_read_once(), if the server incorrectly replies with success but a negative write/read count then we would consider written (negative) <= rsize (positive) because both variables were signed. Make variables unsigned to avoid this problem. The reproducer linked below now fails with the following error instead of a null pointer deref: 9pnet: bogus RWRITE count (4294967295 > 3)

In the Linux kernel, the following vulnerability has been resolved: wifi: ath12k: fix invalid access to memory In ath12k_dp_rx_msdu_coalesce(), rxcb is fetched from skb and boolean is_continuation is part of rxcb. Currently, after freeing the skb, the rxcb->is_continuation accessed again which is wrong since the memory is already freed. This might lead use-after-free error. Hence, fix by locally defining bool is_continuation from rxcb, so that after freeing skb, is_continuation can be used. Compile tested only.

In the Linux kernel, the following vulnerability has been resolved: can: kvaser_pciefd: refine error prone echo_skb_max handling logic echo_skb_max should define the supported upper limit of echo_skb[] allocated inside the netdevice's priv. The corresponding size value provided by this driver to alloc_candev() is KVASER_PCIEFD_CAN_TX_MAX_COUNT which is 17. But later echo_skb_max is rounded up to the nearest power of two (for the max case, that would be 32) and the tx/ack indices calculated further during tx/rx may exceed the upper array boundary. Kasan reported this for the ack case inside kvaser_pciefd_handle_ack_packet(), though the xmit function has actually caught the same thing earlier. BUG: KASAN: slab-out-of-bounds in kvaser_pciefd_handle_ack_packet+0x2d7/0x92a drivers/net/can/kvaser_pciefd.c:1528 Read of size 8 at addr ffff888105e4f078 by task swapper/4/0 CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Not tainted 6.15.0 #12 PREEMPT(voluntary) Call Trace: <IRQ> dump_stack_lvl lib/dump_stack.c:122 print_report mm/kasan/report.c:521 kasan_report mm/kasan/report.c:634 kvaser_pciefd_handle_ack_packet drivers/net/can/kvaser_pciefd.c:1528 kvaser_pciefd_read_packet drivers/net/can/kvaser_pciefd.c:1605 kvaser_pciefd_read_buffer drivers/net/can/kvaser_pciefd.c:1656 kvaser_pciefd_receive_irq drivers/net/can/kvaser_pciefd.c:1684 kvaser_pciefd_irq_handler drivers/net/can/kvaser_pciefd.c:1733 __handle_irq_event_percpu kernel/irq/handle.c:158 handle_irq_event kernel/irq/handle.c:210 handle_edge_irq kernel/irq/chip.c:833 __common_interrupt arch/x86/kernel/irq.c:296 common_interrupt arch/x86/kernel/irq.c:286 </IRQ> Tx max count definitely matters for kvaser_pciefd_tx_avail(), but for seq numbers' generation that's not the case - we're free to calculate them as would be more convenient, not taking tx max count into account. The only downside is that the size of echo_skb[] should correspond to the max seq number (not tx max count), so in some situations a bit more memory would be consumed than could be. Thus make the size of the underlying echo_skb[] sufficient for the rounded max tx value. Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: usb: gadget: configfs: Fix OOB read on empty string write When writing an empty string to either 'qw_sign' or 'landingPage' sysfs attributes, the store functions attempt to access page[l - 1] before validating that the length 'l' is greater than zero. This patch fixes the vulnerability by adding a check at the beginning of os_desc_qw_sign_store() and webusb_landingPage_store() to handle the zero-length input case gracefully by returning immediately.

In the Linux kernel, the following vulnerability has been resolved: md/raid1: Fix stack memory use after return in raid1_reshape In the raid1_reshape function, newpool is allocated on the stack and assigned to conf->r1bio_pool. This results in conf->r1bio_pool.wait.head pointing to a stack address. Accessing this address later can lead to a kernel panic. Example access path: raid1_reshape() { // newpool is on the stack mempool_t newpool, oldpool; // initialize newpool.wait.head to stack address mempool_init(&newpool, ...); conf->r1bio_pool = newpool; } raid1_read_request() or raid1_write_request() { alloc_r1bio() { mempool_alloc() { // if pool->alloc fails remove_element() { --pool->curr_nr; } } } } mempool_free() { if (pool->curr_nr < pool->min_nr) { // pool->wait.head is a stack address // wake_up() will try to access this invalid address // which leads to a kernel panic return; wake_up(&pool->wait); } } Fix: reinit conf->r1bio_pool.wait after assigning newpool.

In the Linux kernel, the following vulnerability has been resolved: riscv: module: Fix out-of-bounds relocation access The current code allows rel[j] to access one element past the end of the relocation section. Simplify to num_relocations which is equivalent to the existing size expression.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid out-of-bounds access in f2fs_truncate_inode_blocks() syzbot reports an UBSAN issue as below: ------------[ cut here ]------------ UBSAN: array-index-out-of-bounds in fs/f2fs/node.h:381:10 index 18446744073709550692 is out of range for type '__le32[5]' (aka 'unsigned int[5]') CPU: 0 UID: 0 PID: 5318 Comm: syz.0.0 Not tainted 6.14.0-rc3-syzkaller-00060-g6537cfb395f3 #0 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 ubsan_epilogue lib/ubsan.c:231 [inline] __ubsan_handle_out_of_bounds+0x121/0x150 lib/ubsan.c:429 get_nid fs/f2fs/node.h:381 [inline] f2fs_truncate_inode_blocks+0xa5e/0xf60 fs/f2fs/node.c:1181 f2fs_do_truncate_blocks+0x782/0x1030 fs/f2fs/file.c:808 f2fs_truncate_blocks+0x10d/0x300 fs/f2fs/file.c:836 f2fs_truncate+0x417/0x720 fs/f2fs/file.c:886 f2fs_file_write_iter+0x1bdb/0x2550 fs/f2fs/file.c:5093 aio_write+0x56b/0x7c0 fs/aio.c:1633 io_submit_one+0x8a7/0x18a0 fs/aio.c:2052 __do_sys_io_submit fs/aio.c:2111 [inline] __se_sys_io_submit+0x171/0x2e0 fs/aio.c:2081 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f238798cde9 index 18446744073709550692 (decimal, unsigned long long) = 0xfffffffffffffc64 (hexadecimal, unsigned long long) = -924 (decimal, long long) In f2fs_truncate_inode_blocks(), UBSAN detects that get_nid() tries to access .i_nid[-924], it means both offset[0] and level should zero. The possible case should be in f2fs_do_truncate_blocks(), we try to truncate inode size to zero, however, dn.ofs_in_node is zero and dn.node_page is not an inode page, so it fails to truncate inode page, and then pass zeroed free_from to f2fs_truncate_inode_blocks(), result in this issue. if (dn.ofs_in_node || IS_INODE(dn.node_page)) { f2fs_truncate_data_blocks_range(&dn, count); free_from += count; } I guess the reason why dn.node_page is not an inode page could be: there are multiple nat entries share the same node block address, once the node block address was reused, f2fs_get_node_page() may load a non-inode block. Let's add a sanity check for such condition to avoid out-of-bounds access issue.

In the Linux kernel, the following vulnerability has been resolved: arm64/ptrace: Fix stack-out-of-bounds read in regs_get_kernel_stack_nth() KASAN reports a stack-out-of-bounds read in regs_get_kernel_stack_nth(). Call Trace: [ 97.283505] BUG: KASAN: stack-out-of-bounds in regs_get_kernel_stack_nth+0xa8/0xc8 [ 97.284677] Read of size 8 at addr ffff800089277c10 by task 1.sh/2550 [ 97.285732] [ 97.286067] CPU: 7 PID: 2550 Comm: 1.sh Not tainted 6.6.0+ #11 [ 97.287032] Hardware name: linux,dummy-virt (DT) [ 97.287815] Call trace: [ 97.288279] dump_backtrace+0xa0/0x128 [ 97.288946] show_stack+0x20/0x38 [ 97.289551] dump_stack_lvl+0x78/0xc8 [ 97.290203] print_address_description.constprop.0+0x84/0x3c8 [ 97.291159] print_report+0xb0/0x280 [ 97.291792] kasan_report+0x84/0xd0 [ 97.292421] __asan_load8+0x9c/0xc0 [ 97.293042] regs_get_kernel_stack_nth+0xa8/0xc8 [ 97.293835] process_fetch_insn+0x770/0xa30 [ 97.294562] kprobe_trace_func+0x254/0x3b0 [ 97.295271] kprobe_dispatcher+0x98/0xe0 [ 97.295955] kprobe_breakpoint_handler+0x1b0/0x210 [ 97.296774] call_break_hook+0xc4/0x100 [ 97.297451] brk_handler+0x24/0x78 [ 97.298073] do_debug_exception+0xac/0x178 [ 97.298785] el1_dbg+0x70/0x90 [ 97.299344] el1h_64_sync_handler+0xcc/0xe8 [ 97.300066] el1h_64_sync+0x78/0x80 [ 97.300699] kernel_clone+0x0/0x500 [ 97.301331] __arm64_sys_clone+0x70/0x90 [ 97.302084] invoke_syscall+0x68/0x198 [ 97.302746] el0_svc_common.constprop.0+0x11c/0x150 [ 97.303569] do_el0_svc+0x38/0x50 [ 97.304164] el0_svc+0x44/0x1d8 [ 97.304749] el0t_64_sync_handler+0x100/0x130 [ 97.305500] el0t_64_sync+0x188/0x190 [ 97.306151] [ 97.306475] The buggy address belongs to stack of task 1.sh/2550 [ 97.307461] and is located at offset 0 in frame: [ 97.308257] __se_sys_clone+0x0/0x138 [ 97.308910] [ 97.309241] This frame has 1 object: [ 97.309873] [48, 184) 'args' [ 97.309876] [ 97.310749] The buggy address belongs to the virtual mapping at [ 97.310749] [ffff800089270000, ffff800089279000) created by: [ 97.310749] dup_task_struct+0xc0/0x2e8 [ 97.313347] [ 97.313674] The buggy address belongs to the physical page: [ 97.314604] page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x14f69a [ 97.315885] flags: 0x15ffffe00000000(node=1|zone=2|lastcpupid=0xfffff) [ 97.316957] raw: 015ffffe00000000 0000000000000000 dead000000000122 0000000000000000 [ 97.318207] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 [ 97.319445] page dumped because: kasan: bad access detected [ 97.320371] [ 97.320694] Memory state around the buggy address: [ 97.321511] ffff800089277b00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 97.322681] ffff800089277b80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 97.323846] >ffff800089277c00: 00 00 f1 f1 f1 f1 f1 f1 00 00 00 00 00 00 00 00 [ 97.325023] ^ [ 97.325683] ffff800089277c80: 00 00 00 00 00 00 00 00 00 f3 f3 f3 f3 f3 f3 f3 [ 97.326856] ffff800089277d00: f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 00 00 This issue seems to be related to the behavior of some gcc compilers and was also fixed on the s390 architecture before: commit d93a855c31b7 ("s390/ptrace: Avoid KASAN false positives in regs_get_kernel_stack_nth()") As described in that commit, regs_get_kernel_stack_nth() has confirmed that `addr` is on the stack, so reading the value at `*addr` should be allowed. Use READ_ONCE_NOCHECK() helper to silence the KASAN check for this case. [will: Use '*addr' as the argument to READ_ONCE_NOCHECK()]

In the Linux kernel, the following vulnerability has been resolved: nvmet: fix out-of-bounds access in nvmet_enable_port When trying to enable a port that has no transport configured yet, nvmet_enable_port() uses NVMF_TRTYPE_MAX (255) to query the transports array, causing an out-of-bounds access: [ 106.058694] BUG: KASAN: global-out-of-bounds in nvmet_enable_port+0x42/0x1da [ 106.058719] Read of size 8 at addr ffffffff89dafa58 by task ln/632 [...] [ 106.076026] nvmet: transport type 255 not supported Since commit 200adac75888, NVMF_TRTYPE_MAX is the default state as configured by nvmet_ports_make(). Avoid this by checking for NVMF_TRTYPE_MAX before proceeding.

In the Linux kernel, the following vulnerability has been resolved: comedi: das16m1: Fix bit shift out of bounds When checking for a supported IRQ number, the following test is used: /* only irqs 2, 3, 4, 5, 6, 7, 10, 11, 12, 14, and 15 are valid */ if ((1 << it->options[1]) & 0xdcfc) { However, `it->options[i]` is an unchecked `int` value from userspace, so the shift amount could be negative or out of bounds. Fix the test by requiring `it->options[1]` to be within bounds before proceeding with the original test.

In the Linux kernel, the following vulnerability has been resolved: mm/rmap: fix potential out-of-bounds page table access during batched unmap As pointed out by David[1], the batched unmap logic in try_to_unmap_one() may read past the end of a PTE table when a large folio's PTE mappings are not fully contained within a single page table. While this scenario might be rare, an issue triggerable from userspace must be fixed regardless of its likelihood. This patch fixes the out-of-bounds access by refactoring the logic into a new helper, folio_unmap_pte_batch(). The new helper correctly calculates the safe batch size by capping the scan at both the VMA and PMD boundaries. To simplify the code, it also supports partial batching (i.e., any number of pages from 1 up to the calculated safe maximum), as there is no strong reason to special-case for fully mapped folios.

In the Linux kernel, the following vulnerability has been resolved: net: ppp: Add bound checking for skb data on ppp_sync_txmung Ensure we have enough data in linear buffer from skb before accessing initial bytes. This prevents potential out-of-bounds accesses when processing short packets. When ppp_sync_txmung receives an incoming package with an empty payload: (remote) gef➤ p *(struct pppoe_hdr *) (skb->head + skb->network_header) $18 = { type = 0x1, ver = 0x1, code = 0x0, sid = 0x2, length = 0x0, tag = 0xffff8880371cdb96 } from the skb struct (trimmed) tail = 0x16, end = 0x140, head = 0xffff88803346f400 "4", data = 0xffff88803346f416 ":\377", truesize = 0x380, len = 0x0, data_len = 0x0, mac_len = 0xe, hdr_len = 0x0, it is not safe to access data[2]. [pabeni@redhat.com: fixed subj typo]

In the Linux kernel, the following vulnerability has been resolved: powerpc/powernv/memtrace: Fix out of bounds issue in memtrace mmap memtrace mmap issue has an out of bounds issue. This patch fixes the by checking that the requested mapping region size should stay within the allocated region size.

In the Linux kernel, the following vulnerability has been resolved: clk: imx: Fix an out-of-bounds access in dispmix_csr_clk_dev_data When num_parents is 4, __clk_register() occurs an out-of-bounds when accessing parent_names member. Use ARRAY_SIZE() instead of hardcode number here. BUG: KASAN: global-out-of-bounds in __clk_register+0x1844/0x20d8 Read of size 8 at addr ffff800086988e78 by task kworker/u24:3/59 Hardware name: NXP i.MX95 19X19 board (DT) Workqueue: events_unbound deferred_probe_work_func Call trace: dump_backtrace+0x94/0xec show_stack+0x18/0x24 dump_stack_lvl+0x8c/0xcc print_report+0x398/0x5fc kasan_report+0xd4/0x114 __asan_report_load8_noabort+0x20/0x2c __clk_register+0x1844/0x20d8 clk_hw_register+0x44/0x110 __clk_hw_register_mux+0x284/0x3a8 imx95_bc_probe+0x4f4/0xa70

In the Linux kernel, the following vulnerability has been resolved: software node: Correct a OOB check in software_node_get_reference_args() software_node_get_reference_args() wants to get @index-th element, so the property value requires at least '(index + 1) * sizeof(*ref)' bytes but that can not be guaranteed by current OOB check, and may cause OOB for malformed property. Fix by using as OOB check '((index + 1) * sizeof(*ref) > prop->length)'.

In the Linux kernel, the following vulnerability has been resolved: net/mdiobus: Fix potential out-of-bounds read/write access When using publicly available tools like 'mdio-tools' to read/write data from/to network interface and its PHY via mdiobus, there is no verification of parameters passed to the ioctl and it accepts any mdio address. Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define, but it is possible to pass higher value than that via ioctl. While read/write operation should generally fail in this case, mdiobus provides stats array, where wrong address may allow out-of-bounds read/write. Fix that by adding address verification before read/write operation. While this excludes this access from any statistics, it improves security of read/write operation.

In the Linux kernel, the following vulnerability has been resolved: jfs: fix array-index-out-of-bounds read in add_missing_indices stbl is s8 but it must contain offsets into slot which can go from 0 to 127. Added a bound check for that error and return -EIO if the check fails. Also make jfs_readdir return with error if add_missing_indices returns with an error.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Fix out-of-bounds read in snd_usb_get_audioformat_uac3() In snd_usb_get_audioformat_uac3(), the length value returned from snd_usb_ctl_msg() is used directly for memory allocation without validation. This length is controlled by the USB device. The allocated buffer is cast to a uac3_cluster_header_descriptor and its fields are accessed without verifying that the buffer is large enough. If the device returns a smaller than expected length, this leads to an out-of-bounds read. Add a length check to ensure the buffer is large enough for uac3_cluster_header_descriptor.

In the Linux kernel, the following vulnerability has been resolved: net: usb: aqc111: fix error handling of usbnet read calls Syzkaller, courtesy of syzbot, identified an error (see report [1]) in aqc111 driver, caused by incomplete sanitation of usb read calls' results. This problem is quite similar to the one fixed in commit 920a9fa27e78 ("net: asix: add proper error handling of usb read errors"). For instance, usbnet_read_cmd() may read fewer than 'size' bytes, even if the caller expected the full amount, and aqc111_read_cmd() will not check its result properly. As [1] shows, this may lead to MAC address in aqc111_bind() being only partly initialized, triggering KMSAN warnings. Fix the issue by verifying that the number of bytes read is as expected and not less. [1] Partial syzbot report: BUG: KMSAN: uninit-value in is_valid_ether_addr include/linux/etherdevice.h:208 [inline] BUG: KMSAN: uninit-value in usbnet_probe+0x2e57/0x4390 drivers/net/usb/usbnet.c:1830 is_valid_ether_addr include/linux/etherdevice.h:208 [inline] usbnet_probe+0x2e57/0x4390 drivers/net/usb/usbnet.c:1830 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:-1 [inline] really_probe+0x4d1/0xd90 drivers/base/dd.c:658 __driver_probe_device+0x268/0x380 drivers/base/dd.c:800 ... Uninit was stored to memory at: dev_addr_mod+0xb0/0x550 net/core/dev_addr_lists.c:582 __dev_addr_set include/linux/netdevice.h:4874 [inline] eth_hw_addr_set include/linux/etherdevice.h:325 [inline] aqc111_bind+0x35f/0x1150 drivers/net/usb/aqc111.c:717 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 ... Uninit was stored to memory at: ether_addr_copy include/linux/etherdevice.h:305 [inline] aqc111_read_perm_mac drivers/net/usb/aqc111.c:663 [inline] aqc111_bind+0x794/0x1150 drivers/net/usb/aqc111.c:713 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772 usb_probe_interface+0xd01/0x1310 drivers/usb/core/driver.c:396 call_driver_probe drivers/base/dd.c:-1 [inline] ... Local variable buf.i created at: aqc111_read_perm_mac drivers/net/usb/aqc111.c:656 [inline] aqc111_bind+0x221/0x1150 drivers/net/usb/aqc111.c:713 usbnet_probe+0xbe6/0x4390 drivers/net/usb/usbnet.c:1772

In the Linux kernel, the following vulnerability has been resolved: pinctrl: at91: Fix possible out-of-boundary access at91_gpio_probe() doesn't check that given OF alias is not available or something went wrong when trying to get it. This might have consequences when accessing gpio_chips array with that value as an index. Note, that BUG() can be compiled out and hence won't actually perform the required checks.

In the Linux kernel, the following vulnerability has been resolved: can: bcm: add locking for bcm_op runtime updates The CAN broadcast manager (CAN BCM) can send a sequence of CAN frames via hrtimer. The content and also the length of the sequence can be changed resp reduced at runtime where the 'currframe' counter is then set to zero. Although this appeared to be a safe operation the updates of 'currframe' can be triggered from user space and hrtimer context in bcm_can_tx(). Anderson Nascimento created a proof of concept that triggered a KASAN slab-out-of-bounds read access which can be prevented with a spin_lock_bh. At the rework of bcm_can_tx() the 'count' variable has been moved into the protected section as this variable can be modified from both contexts too.

In the Linux kernel, the following vulnerability has been resolved: arm64: mops: Do not dereference src reg for a set operation The source register is not used for SET* and reading it can result in a UBSAN out-of-bounds array access error, specifically when the MOPS exception is taken from a SET* sequence with XZR (reg 31) as the source. Architecturally this is the only case where a src/dst/size field in the ESR can be reported as 31. Prior to 2de451a329cf662b the code in do_el0_mops() was benign as the use of pt_regs_read_reg() prevented the out-of-bounds access.

In the Linux kernel, the following vulnerability has been resolved: HID: uclogic: Fix user-memory-access bug in uclogic_params_ugee_v2_init_event_hooks() When CONFIG_HID_UCLOGIC=y and CONFIG_KUNIT_ALL_TESTS=y, launch kernel and then the below user-memory-access bug occurs. In hid_test_uclogic_params_cleanup_event_hooks(),it call uclogic_params_ugee_v2_init_event_hooks() with the first arg=NULL, so when it calls uclogic_params_ugee_v2_has_battery(), the hid_get_drvdata() will access hdev->dev with hdev=NULL, which will cause below user-memory-access. So add a fake_device with quirks member and call hid_set_drvdata() to assign hdev->dev->driver_data which avoids the null-ptr-def bug for drvdata->quirks in uclogic_params_ugee_v2_has_battery(). After applying this patch, the below user-memory-access bug never occurs. general protection fault, probably for non-canonical address 0xdffffc0000000329: 0000 [#1] PREEMPT SMP KASAN KASAN: probably user-memory-access in range [0x0000000000001948-0x000000000000194f] CPU: 5 PID: 2189 Comm: kunit_try_catch Tainted: G B W N 6.6.0-rc2+ #30 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 Code: f3 f3 65 48 8b 14 25 28 00 00 00 48 89 54 24 60 31 d2 48 89 fa c7 44 24 30 00 00 00 00 48 c7 44 24 28 02 f8 02 01 48 c1 ea 03 <80> 3c 02 00 0f 85 2c 04 00 00 48 8b 9d 48 19 00 00 48 b8 00 00 00 RSP: 0000:ffff88810679fc88 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000004 RCX: 0000000000000000 RDX: 0000000000000329 RSI: ffff88810679fd88 RDI: 0000000000001948 RBP: 0000000000000000 R08: 0000000000000000 R09: ffffed1020f639f0 R10: ffff888107b1cf87 R11: 0000000000000400 R12: 1ffff11020cf3f92 R13: ffff88810679fd88 R14: ffff888100b97b08 R15: ffff8881030bb080 FS: 0000000000000000(0000) GS:ffff888119e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000005286001 CR4: 0000000000770ee0 DR0: ffffffff8fdd6cf4 DR1: ffffffff8fdd6cf5 DR2: ffffffff8fdd6cf6 DR3: ffffffff8fdd6cf7 DR6: 00000000fffe0ff0 DR7: 0000000000000600 PKRU: 55555554 Call Trace: <TASK> ? die_addr+0x3d/0xa0 ? exc_general_protection+0x144/0x220 ? asm_exc_general_protection+0x22/0x30 ? uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 ? sched_clock_cpu+0x69/0x550 ? uclogic_parse_ugee_v2_desc_gen_params+0x70/0x70 ? load_balance+0x2950/0x2950 ? rcu_trc_cmpxchg_need_qs+0x67/0xa0 hid_test_uclogic_params_cleanup_event_hooks+0x9e/0x1a0 ? uclogic_params_ugee_v2_init_event_hooks+0x600/0x600 ? __switch_to+0x5cf/0xe60 ? migrate_enable+0x260/0x260 ? __kthread_parkme+0x83/0x150 ? kunit_try_run_case_cleanup+0xe0/0xe0 kunit_generic_run_threadfn_adapter+0x4a/0x90 ? kunit_try_catch_throw+0x80/0x80 kthread+0x2b5/0x380 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork+0x2d/0x70 ? kthread_complete_and_exit+0x20/0x20 ret_from_fork_asm+0x11/0x20 </TASK> Modules linked in: Dumping ftrace buffer: (ftrace buffer empty) ---[ end trace 0000000000000000 ]--- RIP: 0010:uclogic_params_ugee_v2_init_event_hooks+0x87/0x600 Code: f3 f3 65 48 8b 14 25 28 00 00 00 48 89 54 24 60 31 d2 48 89 fa c7 44 24 30 00 00 00 00 48 c7 44 24 28 02 f8 02 01 48 c1 ea 03 <80> 3c 02 00 0f 85 2c 04 00 00 48 8b 9d 48 19 00 00 48 b8 00 00 00 RSP: 0000:ffff88810679fc88 EFLAGS: 00010202 RAX: dffffc0000000000 RBX: 0000000000000004 RCX: 0000000000000000 RDX: 0000000000000329 RSI: ffff88810679fd88 RDI: 0000000000001948 RBP: 0000000000000000 R08: 0000000000000000 R09: ffffed1020f639f0 R10: ffff888107b1cf87 R11: 0000000000000400 R12: 1ffff11020cf3f92 R13: ffff88810679fd88 R14: ffff888100b97b08 R15: ffff8881030bb080 FS: 0000000000000000(0000) GS:ffff888119e80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 0000000005286001 CR4: 0000000000770ee0 DR0: ffffffff8fdd6cf4 DR1: ---truncated---

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_devcd_dump: fix out-of-bounds via dev_coredumpv Currently both dev_coredumpv and skb_put_data in hci_devcd_dump use hdev->dump.head. However, dev_coredumpv can free the buffer. From dev_coredumpm_timeout documentation, which is used by dev_coredumpv: > Creates a new device coredump for the given device. If a previous one hasn't > been read yet, the new coredump is discarded. The data lifetime is determined > by the device coredump framework and when it is no longer needed the @free > function will be called to free the data. If the data has not been read by the userspace yet, dev_coredumpv will discard new buffer, freeing hdev->dump.head. This leads to vmalloc-out-of-bounds error when skb_put_data tries to access hdev->dump.head. A crash report from syzbot illustrates this: ================================================================== BUG: KASAN: vmalloc-out-of-bounds in skb_put_data include/linux/skbuff.h:2752 [inline] BUG: KASAN: vmalloc-out-of-bounds in hci_devcd_dump+0x142/0x240 net/bluetooth/coredump.c:258 Read of size 140 at addr ffffc90004ed5000 by task kworker/u9:2/5844 CPU: 1 UID: 0 PID: 5844 Comm: kworker/u9:2 Not tainted 6.14.0-syzkaller-10892-g4e82c87058f4 #0 PREEMPT(full) Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Workqueue: hci0 hci_devcd_timeout Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:408 [inline] print_report+0xc3/0x670 mm/kasan/report.c:521 kasan_report+0xe0/0x110 mm/kasan/report.c:634 check_region_inline mm/kasan/generic.c:183 [inline] kasan_check_range+0xef/0x1a0 mm/kasan/generic.c:189 __asan_memcpy+0x23/0x60 mm/kasan/shadow.c:105 skb_put_data include/linux/skbuff.h:2752 [inline] hci_devcd_dump+0x142/0x240 net/bluetooth/coredump.c:258 hci_devcd_timeout+0xb5/0x2e0 net/bluetooth/coredump.c:413 process_one_work+0x9cc/0x1b70 kernel/workqueue.c:3238 process_scheduled_works kernel/workqueue.c:3319 [inline] worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400 kthread+0x3c2/0x780 kernel/kthread.c:464 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> The buggy address ffffc90004ed5000 belongs to a vmalloc virtual mapping Memory state around the buggy address: ffffc90004ed4f00: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc90004ed4f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 >ffffc90004ed5000: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ^ ffffc90004ed5080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc90004ed5100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ================================================================== To avoid this issue, reorder dev_coredumpv to be called after skb_put_data that does not free the data.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid out-of-boundary access in dnode page As Jiaming Zhang reported: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x1c1/0x2a0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:378 [inline] print_report+0x17e/0x800 mm/kasan/report.c:480 kasan_report+0x147/0x180 mm/kasan/report.c:593 data_blkaddr fs/f2fs/f2fs.h:3053 [inline] f2fs_data_blkaddr fs/f2fs/f2fs.h:3058 [inline] f2fs_get_dnode_of_data+0x1a09/0x1c40 fs/f2fs/node.c:855 f2fs_reserve_block+0x53/0x310 fs/f2fs/data.c:1195 prepare_write_begin fs/f2fs/data.c:3395 [inline] f2fs_write_begin+0xf39/0x2190 fs/f2fs/data.c:3594 generic_perform_write+0x2c7/0x910 mm/filemap.c:4112 f2fs_buffered_write_iter fs/f2fs/file.c:4988 [inline] f2fs_file_write_iter+0x1ec8/0x2410 fs/f2fs/file.c:5216 new_sync_write fs/read_write.c:593 [inline] vfs_write+0x546/0xa90 fs/read_write.c:686 ksys_write+0x149/0x250 fs/read_write.c:738 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xf3/0x3d0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f The root cause is in the corrupted image, there is a dnode has the same node id w/ its inode, so during f2fs_get_dnode_of_data(), it tries to access block address in dnode at offset 934, however it parses the dnode as inode node, so that get_dnode_addr() returns 360, then it tries to access page address from 360 + 934 * 4 = 4096 w/ 4 bytes. To fix this issue, let's add sanity check for node id of all direct nodes during f2fs_get_dnode_of_data().

An out-of-bounds read vulnerability was found in smbCalcSize in fs/smb/client/netmisc.c in the Linux Kernel. This issue could allow a local attacker to crash the system or leak internal kernel information.

An out-of-bounds read vulnerability was found in smb2_dump_detail in fs/smb/client/smb2ops.c in the Linux Kernel. This issue could allow a local attacker to crash the system or leak internal kernel information.

In the Linux kernel, the following vulnerability has been resolved: ring-buffer: Fix deadloop issue on reading trace_pipe Soft lockup occurs when reading file 'trace_pipe': watchdog: BUG: soft lockup - CPU#6 stuck for 22s! [cat:4488] [...] RIP: 0010:ring_buffer_empty_cpu+0xed/0x170 RSP: 0018:ffff88810dd6fc48 EFLAGS: 00000246 RAX: 0000000000000000 RBX: 0000000000000246 RCX: ffffffff93d1aaeb RDX: ffff88810a280040 RSI: 0000000000000008 RDI: ffff88811164b218 RBP: ffff88811164b218 R08: 0000000000000000 R09: ffff88815156600f R10: ffffed102a2acc01 R11: 0000000000000001 R12: 0000000051651901 R13: 0000000000000000 R14: ffff888115e49500 R15: 0000000000000000 [...] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f8d853c2000 CR3: 000000010dcd8000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: __find_next_entry+0x1a8/0x4b0 ? peek_next_entry+0x250/0x250 ? down_write+0xa5/0x120 ? down_write_killable+0x130/0x130 trace_find_next_entry_inc+0x3b/0x1d0 tracing_read_pipe+0x423/0xae0 ? tracing_splice_read_pipe+0xcb0/0xcb0 vfs_read+0x16b/0x490 ksys_read+0x105/0x210 ? __ia32_sys_pwrite64+0x200/0x200 ? switch_fpu_return+0x108/0x220 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x61/0xc6 Through the vmcore, I found it's because in tracing_read_pipe(), ring_buffer_empty_cpu() found some buffer is not empty but then it cannot read anything due to "rb_num_of_entries() == 0" always true, Then it infinitely loop the procedure due to user buffer not been filled, see following code path: tracing_read_pipe() { ... ... waitagain: tracing_wait_pipe() // 1. find non-empty buffer here trace_find_next_entry_inc() // 2. loop here try to find an entry __find_next_entry() ring_buffer_empty_cpu(); // 3. find non-empty buffer peek_next_entry() // 4. but peek always return NULL ring_buffer_peek() rb_buffer_peek() rb_get_reader_page() // 5. because rb_num_of_entries() == 0 always true here // then return NULL // 6. user buffer not been filled so goto 'waitgain' // and eventually leads to an deadloop in kernel!!! } By some analyzing, I found that when resetting ringbuffer, the 'entries' of its pages are not all cleared (see rb_reset_cpu()). Then when reducing the ringbuffer, and if some reduced pages exist dirty 'entries' data, they will be added into 'cpu_buffer->overrun' (see rb_remove_pages()), which cause wrong 'overrun' count and eventually cause the deadloop issue. To fix it, we need to clear every pages in rb_reset_cpu().

An issue was discovered in the Linux kernel 3.16 through 5.5.6. set_fdc in drivers/block/floppy.c leads to a wait_til_ready out-of-bounds read because the FDC index is not checked for errors before assigning it, aka CID-2e90ca68b0d2.

In the Linux kernel, the following vulnerability has been resolved: iavf: Fix out-of-bounds when setting channels on remove If we set channels greater during iavf_remove(), and waiting reset done would be timeout, then returned with error but changed num_active_queues directly, that will lead to OOB like the following logs. Because the num_active_queues is greater than tx/rx_rings[] allocated actually. Reproducer: [root@host ~]# cat repro.sh #!/bin/bash pf_dbsf="0000:41:00.0" vf0_dbsf="0000:41:02.0" g_pids=() function do_set_numvf() { echo 2 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) echo 0 >/sys/bus/pci/devices/${pf_dbsf}/sriov_numvfs sleep $((RANDOM%3+1)) } function do_set_channel() { local nic=$(ls -1 --indicator-style=none /sys/bus/pci/devices/${vf0_dbsf}/net/) [ -z "$nic" ] && { sleep $((RANDOM%3)) ; return 1; } ifconfig $nic 192.168.18.5 netmask 255.255.255.0 ifconfig $nic up ethtool -L $nic combined 1 ethtool -L $nic combined 4 sleep $((RANDOM%3)) } function on_exit() { local pid for pid in "${g_pids[@]}"; do kill -0 "$pid" &>/dev/null && kill "$pid" &>/dev/null done g_pids=() } trap "on_exit; exit" EXIT while :; do do_set_numvf ; done & g_pids+=($!) while :; do do_set_channel ; done & g_pids+=($!) wait Result: [ 3506.152887] iavf 0000:41:02.0: Removing device [ 3510.400799] ================================================================== [ 3510.400820] BUG: KASAN: slab-out-of-bounds in iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400823] Read of size 8 at addr ffff88b6f9311008 by task repro.sh/55536 [ 3510.400823] [ 3510.400830] CPU: 101 PID: 55536 Comm: repro.sh Kdump: loaded Tainted: G O --------- -t - 4.18.0 #1 [ 3510.400832] Hardware name: Powerleader PR2008AL/H12DSi-N6, BIOS 2.0 04/09/2021 [ 3510.400835] Call Trace: [ 3510.400851] dump_stack+0x71/0xab [ 3510.400860] print_address_description+0x6b/0x290 [ 3510.400865] ? iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400868] kasan_report+0x14a/0x2b0 [ 3510.400873] iavf_free_all_tx_resources+0x156/0x160 [iavf] [ 3510.400880] iavf_remove+0x2b6/0xc70 [iavf] [ 3510.400884] ? iavf_free_all_rx_resources+0x160/0x160 [iavf] [ 3510.400891] ? wait_woken+0x1d0/0x1d0 [ 3510.400895] ? notifier_call_chain+0xc1/0x130 [ 3510.400903] pci_device_remove+0xa8/0x1f0 [ 3510.400910] device_release_driver_internal+0x1c6/0x460 [ 3510.400916] pci_stop_bus_device+0x101/0x150 [ 3510.400919] pci_stop_and_remove_bus_device+0xe/0x20 [ 3510.400924] pci_iov_remove_virtfn+0x187/0x420 [ 3510.400927] ? pci_iov_add_virtfn+0xe10/0xe10 [ 3510.400929] ? pci_get_subsys+0x90/0x90 [ 3510.400932] sriov_disable+0xed/0x3e0 [ 3510.400936] ? bus_find_device+0x12d/0x1a0 [ 3510.400953] i40e_free_vfs+0x754/0x1210 [i40e] [ 3510.400966] ? i40e_reset_all_vfs+0x880/0x880 [i40e] [ 3510.400968] ? pci_get_device+0x7c/0x90 [ 3510.400970] ? pci_get_subsys+0x90/0x90 [ 3510.400982] ? pci_vfs_assigned.part.7+0x144/0x210 [ 3510.400987] ? __mutex_lock_slowpath+0x10/0x10 [ 3510.400996] i40e_pci_sriov_configure+0x1fa/0x2e0 [i40e] [ 3510.401001] sriov_numvfs_store+0x214/0x290 [ 3510.401005] ? sriov_totalvfs_show+0x30/0x30 [ 3510.401007] ? __mutex_lock_slowpath+0x10/0x10 [ 3510.401011] ? __check_object_size+0x15a/0x350 [ 3510.401018] kernfs_fop_write+0x280/0x3f0 [ 3510.401022] vfs_write+0x145/0x440 [ 3510.401025] ksys_write+0xab/0x160 [ 3510.401028] ? __ia32_sys_read+0xb0/0xb0 [ 3510.401031] ? fput_many+0x1a/0x120 [ 3510.401032] ? filp_close+0xf0/0x130 [ 3510.401038] do_syscall_64+0xa0/0x370 [ 3510.401041] ? page_fault+0x8/0x30 [ 3510.401043] entry_SYSCALL_64_after_hwframe+0x65/0xca [ 3510.401073] RIP: 0033:0x7f3a9bb842c0 [ 3510.401079] Code: 73 01 c3 48 8b 0d d8 cb 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 89 24 2d 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d ---truncated---

In the Linux kernel, the following vulnerability has been resolved: smb3: fix for slab out of bounds on mount to ksmbd With KASAN enabled, it is possible to get a slab out of bounds during mount to ksmbd due to missing check in parse_server_interfaces() (see below): BUG: KASAN: slab-out-of-bounds in parse_server_interfaces+0x14ee/0x1880 [cifs] Read of size 4 at addr ffff8881433dba98 by task mount/9827 CPU: 5 UID: 0 PID: 9827 Comm: mount Tainted: G OE 6.16.0-rc2-kasan #2 PREEMPT(voluntary) Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: Dell Inc. Precision Tower 3620/0MWYPT, BIOS 2.13.1 06/14/2019 Call Trace: <TASK> dump_stack_lvl+0x9f/0xf0 print_report+0xd1/0x670 __virt_addr_valid+0x22c/0x430 ? parse_server_interfaces+0x14ee/0x1880 [cifs] ? kasan_complete_mode_report_info+0x2a/0x1f0 ? parse_server_interfaces+0x14ee/0x1880 [cifs] kasan_report+0xd6/0x110 parse_server_interfaces+0x14ee/0x1880 [cifs] __asan_report_load_n_noabort+0x13/0x20 parse_server_interfaces+0x14ee/0x1880 [cifs] ? __pfx_parse_server_interfaces+0x10/0x10 [cifs] ? trace_hardirqs_on+0x51/0x60 SMB3_request_interfaces+0x1ad/0x3f0 [cifs] ? __pfx_SMB3_request_interfaces+0x10/0x10 [cifs] ? SMB2_tcon+0x23c/0x15d0 [cifs] smb3_qfs_tcon+0x173/0x2b0 [cifs] ? __pfx_smb3_qfs_tcon+0x10/0x10 [cifs] ? cifs_get_tcon+0x105d/0x2120 [cifs] ? do_raw_spin_unlock+0x5d/0x200 ? cifs_get_tcon+0x105d/0x2120 [cifs] ? __pfx_smb3_qfs_tcon+0x10/0x10 [cifs] cifs_mount_get_tcon+0x369/0xb90 [cifs] ? dfs_cache_find+0xe7/0x150 [cifs] dfs_mount_share+0x985/0x2970 [cifs] ? check_path.constprop.0+0x28/0x50 ? save_trace+0x54/0x370 ? __pfx_dfs_mount_share+0x10/0x10 [cifs] ? __lock_acquire+0xb82/0x2ba0 ? __kasan_check_write+0x18/0x20 cifs_mount+0xbc/0x9e0 [cifs] ? __pfx_cifs_mount+0x10/0x10 [cifs] ? do_raw_spin_unlock+0x5d/0x200 ? cifs_setup_cifs_sb+0x29d/0x810 [cifs] cifs_smb3_do_mount+0x263/0x1990 [cifs]