In the Linux kernel, the following vulnerability has been resolved: afs: Fix lock recursion afs_wake_up_async_call() can incur lock recursion. The problem is that it is called from AF_RXRPC whilst holding the ->notify_lock, but it tries to take a ref on the afs_call struct in order to pass it to a work queue - but if the afs_call is already queued, we then have an extraneous ref that must be put... calling afs_put_call() may call back down into AF_RXRPC through rxrpc_kernel_shutdown_call(), however, which might try taking the ->notify_lock again. This case isn't very common, however, so defer it to a workqueue. The oops looks something like: BUG: spinlock recursion on CPU#0, krxrpcio/7001/1646 lock: 0xffff888141399b30, .magic: dead4ead, .owner: krxrpcio/7001/1646, .owner_cpu: 0 CPU: 0 UID: 0 PID: 1646 Comm: krxrpcio/7001 Not tainted 6.12.0-rc2-build3+ #4351 Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014 Call Trace: <TASK> dump_stack_lvl+0x47/0x70 do_raw_spin_lock+0x3c/0x90 rxrpc_kernel_shutdown_call+0x83/0xb0 afs_put_call+0xd7/0x180 rxrpc_notify_socket+0xa0/0x190 rxrpc_input_split_jumbo+0x198/0x1d0 rxrpc_input_data+0x14b/0x1e0 ? rxrpc_input_call_packet+0xc2/0x1f0 rxrpc_input_call_event+0xad/0x6b0 rxrpc_input_packet_on_conn+0x1e1/0x210 rxrpc_input_packet+0x3f2/0x4d0 rxrpc_io_thread+0x243/0x410 ? __pfx_rxrpc_io_thread+0x10/0x10 kthread+0xcf/0xe0 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x24/0x40 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: nbd: fix incomplete validation of ioctl arg We tested and found an alarm caused by nbd_ioctl arg without verification. The UBSAN warning calltrace like below: UBSAN: Undefined behaviour in fs/buffer.c:1709:35 signed integer overflow: -9223372036854775808 - 1 cannot be represented in type 'long long int' CPU: 3 PID: 2523 Comm: syz-executor.0 Not tainted 4.19.90 #1 Hardware name: linux,dummy-virt (DT) Call trace: dump_backtrace+0x0/0x3f0 arch/arm64/kernel/time.c:78 show_stack+0x28/0x38 arch/arm64/kernel/traps.c:158 __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x170/0x1dc lib/dump_stack.c:118 ubsan_epilogue+0x18/0xb4 lib/ubsan.c:161 handle_overflow+0x188/0x1dc lib/ubsan.c:192 __ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:206 __block_write_full_page+0x94c/0xa20 fs/buffer.c:1709 block_write_full_page+0x1f0/0x280 fs/buffer.c:2934 blkdev_writepage+0x34/0x40 fs/block_dev.c:607 __writepage+0x68/0xe8 mm/page-writeback.c:2305 write_cache_pages+0x44c/0xc70 mm/page-writeback.c:2240 generic_writepages+0xdc/0x148 mm/page-writeback.c:2329 blkdev_writepages+0x2c/0x38 fs/block_dev.c:2114 do_writepages+0xd4/0x250 mm/page-writeback.c:2344 The reason for triggering this warning is __block_write_full_page() -> i_size_read(inode) - 1 overflow. inode->i_size is assigned in __nbd_ioctl() -> nbd_set_size() -> bytesize. We think it is necessary to limit the size of arg to prevent errors. Moreover, __nbd_ioctl() -> nbd_add_socket(), arg will be cast to int. Assuming the value of arg is 0x80000000000000001) (on a 64-bit machine), it will become 1 after the coercion, which will return unexpected results. Fix it by adding checks to prevent passing in too large numbers.

In the Linux kernel, the following vulnerability has been resolved: KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest() In commit 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C") kvm_start_guest() became idle_kvm_start_guest(). The old code allocated a stack frame on the emergency stack, but didn't use the frame to store anything, and also didn't store anything in its caller's frame. idle_kvm_start_guest() on the other hand is written more like a normal C function, it creates a frame on entry, and also stores CR/LR into its callers frame (per the ABI). The problem is that there is no caller frame on the emergency stack. The emergency stack for a given CPU is allocated with: paca_ptrs[i]->emergency_sp = alloc_stack(limit, i) + THREAD_SIZE; So emergency_sp actually points to the first address above the emergency stack allocation for a given CPU, we must not store above it without first decrementing it to create a frame. This is different to the regular kernel stack, paca->kstack, which is initialised to point at an initial frame that is ready to use. idle_kvm_start_guest() stores the backchain, CR and LR all of which write outside the allocation for the emergency stack. It then creates a stack frame and saves the non-volatile registers. Unfortunately the frame it creates is not large enough to fit the non-volatiles, and so the saving of the non-volatile registers also writes outside the emergency stack allocation. The end result is that we corrupt whatever is at 0-24 bytes, and 112-248 bytes above the emergency stack allocation. In practice this has gone unnoticed because the memory immediately above the emergency stack happens to be used for other stack allocations, either another CPUs mc_emergency_sp or an IRQ stack. See the order of calls to irqstack_early_init() and emergency_stack_init(). The low addresses of another stack are the top of that stack, and so are only used if that stack is under extreme pressue, which essentially never happens in practice - and if it did there's a high likelyhood we'd crash due to that stack overflowing. Still, we shouldn't be corrupting someone else's stack, and it is purely luck that we aren't corrupting something else. To fix it we save CR/LR into the caller's frame using the existing r1 on entry, we then create a SWITCH_FRAME_SIZE frame (which has space for pt_regs) on the emergency stack with the backchain pointing to the existing stack, and then finally we switch to the new frame on the emergency stack.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix recursive locking in RPC handle list access Since commit 305853cce3794 ("ksmbd: Fix race condition in RPC handle list access"), ksmbd_session_rpc_method() attempts to lock sess->rpc_lock. This causes hung connections / tasks when a client attempts to open a named pipe. Using Samba's rpcclient tool: $ rpcclient //192.168.1.254 -U user%password $ rpcclient $> srvinfo <connection hung here> Kernel side: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/0:0 state:D stack:0 pid:5021 tgid:5021 ppid:2 flags:0x00200000 Workqueue: ksmbd-io handle_ksmbd_work Call trace: __schedule from schedule+0x3c/0x58 schedule from schedule_preempt_disabled+0xc/0x10 schedule_preempt_disabled from rwsem_down_read_slowpath+0x1b0/0x1d8 rwsem_down_read_slowpath from down_read+0x28/0x30 down_read from ksmbd_session_rpc_method+0x18/0x3c ksmbd_session_rpc_method from ksmbd_rpc_open+0x34/0x68 ksmbd_rpc_open from ksmbd_session_rpc_open+0x194/0x228 ksmbd_session_rpc_open from create_smb2_pipe+0x8c/0x2c8 create_smb2_pipe from smb2_open+0x10c/0x27ac smb2_open from handle_ksmbd_work+0x238/0x3dc handle_ksmbd_work from process_scheduled_works+0x160/0x25c process_scheduled_works from worker_thread+0x16c/0x1e8 worker_thread from kthread+0xa8/0xb8 kthread from ret_from_fork+0x14/0x38 Exception stack(0x8529ffb0 to 0x8529fff8) The task deadlocks because the lock is already held: ksmbd_session_rpc_open down_write(&sess->rpc_lock) ksmbd_rpc_open ksmbd_session_rpc_method down_read(&sess->rpc_lock) <-- deadlock Adjust ksmbd_session_rpc_method() callers to take the lock when necessary.

In the Linux kernel, the following vulnerability has been resolved: powerpc/eeh: fix recursive pci_lock_rescan_remove locking in EEH event handling The recent commit 1010b4c012b0 ("powerpc/eeh: Make EEH driver device hotplug safe") restructured the EEH driver to improve synchronization with the PCI hotplug layer. However, it inadvertently moved pci_lock_rescan_remove() outside its intended scope in eeh_handle_normal_event(), leading to broken PCI error reporting and improper EEH event triggering. Specifically, eeh_handle_normal_event() acquired pci_lock_rescan_remove() before calling eeh_pe_bus_get(), but eeh_pe_bus_get() itself attempts to acquire the same lock internally, causing nested locking and disrupting normal EEH event handling paths. This patch adds a boolean parameter do_lock to _eeh_pe_bus_get(), with two public wrappers: eeh_pe_bus_get() with locking enabled. eeh_pe_bus_get_nolock() that skips locking. Callers that already hold pci_lock_rescan_remove() now use eeh_pe_bus_get_nolock() to avoid recursive lock acquisition. Additionally, pci_lock_rescan_remove() calls are restored to the correct position—after eeh_pe_bus_get() and immediately before iterating affected PEs and devices. This ensures EEH-triggered PCI removes occur under proper bus rescan locking without recursive lock contention. The eeh_pe_loc_get() function has been split into two functions: eeh_pe_loc_get(struct eeh_pe *pe) which retrieves the loc for given PE. eeh_pe_loc_get_bus(struct pci_bus *bus) which retrieves the location code for given bus. This resolves lockdep warnings such as: <snip> [ 84.964298] [ T928] ============================================ [ 84.964304] [ T928] WARNING: possible recursive locking detected [ 84.964311] [ T928] 6.18.0-rc3 #51 Not tainted [ 84.964315] [ T928] -------------------------------------------- [ 84.964320] [ T928] eehd/928 is trying to acquire lock: [ 84.964324] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40 [ 84.964342] [ T928] but task is already holding lock: [ 84.964347] [ T928] c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40 [ 84.964357] [ T928] other info that might help us debug this: [ 84.964363] [ T928] Possible unsafe locking scenario: [ 84.964367] [ T928] CPU0 [ 84.964370] [ T928] ---- [ 84.964373] [ T928] lock(pci_rescan_remove_lock); [ 84.964378] [ T928] lock(pci_rescan_remove_lock); [ 84.964383] [ T928] *** DEADLOCK *** [ 84.964388] [ T928] May be due to missing lock nesting notation [ 84.964393] [ T928] 1 lock held by eehd/928: [ 84.964397] [ T928] #0: c000000003b29d58 (pci_rescan_remove_lock){+.+.}-{3:3}, at: pci_lock_rescan_remove+0x28/0x40 [ 84.964408] [ T928] stack backtrace: [ 84.964414] [ T928] CPU: 2 UID: 0 PID: 928 Comm: eehd Not tainted 6.18.0-rc3 #51 VOLUNTARY [ 84.964417] [ T928] Hardware name: IBM,9080-HEX POWER10 (architected) 0x800200 0xf000006 of:IBM,FW1060.00 (NH1060_022) hv:phyp pSeries [ 84.964419] [ T928] Call Trace: [ 84.964420] [ T928] [c0000011a7157990] [c000000001705de4] dump_stack_lvl+0xc8/0x130 (unreliable) [ 84.964424] [ T928] [c0000011a71579d0] [c0000000002f66e0] print_deadlock_bug+0x430/0x440 [ 84.964428] [ T928] [c0000011a7157a70] [c0000000002fd0c0] __lock_acquire+0x1530/0x2d80 [ 84.964431] [ T928] [c0000011a7157ba0] [c0000000002fea54] lock_acquire+0x144/0x410 [ 84.964433] [ T928] [c0000011a7157cb0] [c0000011a7157cb0] __mutex_lock+0xf4/0x1050 [ 84.964436] [ T928] [c0000011a7157e00] [c000000000de21d8] pci_lock_rescan_remove+0x28/0x40 [ 84.964439] [ T928] [c0000011a7157e20] [c00000000004ed98] eeh_pe_bus_get+0x48/0xc0 [ 84.964442] [ T928] [c0000011a7157e50] [c00000 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: block: avoid possible overflow for chunk_sectors check in blk_stack_limits() In blk_stack_limits(), we check that the t->chunk_sectors value is a multiple of the t->physical_block_size value. However, by finding the chunk_sectors value in bytes, we may overflow the unsigned int which holds chunk_sectors, so change the check to be based on sectors.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: KVM: Fix stack protector issue in send_ipi_data() Function kvm_io_bus_read() is called in function send_ipi_data(), buffer size of parameter *val should be at least 8 bytes. Since some emulation functions like loongarch_ipi_readl() and kvm_eiointc_read() will write the buffer *val with 8 bytes signed extension regardless parameter len. Otherwise there will be buffer overflow issue when CONFIG_STACKPROTECTOR is enabled. The bug report is shown as follows: Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: send_ipi_data+0x194/0x1a0 [kvm] CPU: 11 UID: 107 PID: 2692 Comm: CPU 0/KVM Not tainted 6.17.0-rc1+ #102 PREEMPT(full) Stack : 9000000005901568 0000000000000000 9000000003af371c 900000013c68c000 900000013c68f850 900000013c68f858 0000000000000000 900000013c68f998 900000013c68f990 900000013c68f990 900000013c68f6c0 fffffffffffdb058 fffffffffffdb0e0 900000013c68f858 911e1d4d39cf0ec2 9000000105657a00 0000000000000001 fffffffffffffffe 0000000000000578 282049464555206e 6f73676e6f6f4c20 0000000000000001 00000000086b4000 0000000000000000 0000000000000000 0000000000000000 9000000005709968 90000000058f9000 900000013c68fa68 900000013c68fab4 90000000029279f0 900000010153f940 900000010001f360 0000000000000000 9000000003af3734 000000004390000c 00000000000000b0 0000000000000004 0000000000000000 0000000000071c1d ... Call Trace: [<9000000003af3734>] show_stack+0x5c/0x180 [<9000000003aed168>] dump_stack_lvl+0x6c/0x9c [<9000000003ad0ab0>] vpanic+0x108/0x2c4 [<9000000003ad0ca8>] panic+0x3c/0x40 [<9000000004eb0a1c>] __stack_chk_fail+0x14/0x18 [<ffff8000023473f8>] send_ipi_data+0x190/0x1a0 [kvm] [<ffff8000023313e4>] __kvm_io_bus_write+0xa4/0xe8 [kvm] [<ffff80000233147c>] kvm_io_bus_write+0x54/0x90 [kvm] [<ffff80000233f9f8>] kvm_emu_iocsr+0x180/0x310 [kvm] [<ffff80000233fe08>] kvm_handle_gspr+0x280/0x478 [kvm] [<ffff8000023443e8>] kvm_handle_exit+0xc0/0x130 [kvm]

In the Linux kernel, the following vulnerability has been resolved: eventpoll: Fix semi-unbounded recursion Ensure that epoll instances can never form a graph deeper than EP_MAX_NESTS+1 links. Currently, ep_loop_check_proc() ensures that the graph is loop-free and does some recursion depth checks, but those recursion depth checks don't limit the depth of the resulting tree for two reasons: - They don't look upwards in the tree. - If there are multiple downwards paths of different lengths, only one of the paths is actually considered for the depth check since commit 28d82dc1c4ed ("epoll: limit paths"). Essentially, the current recursion depth check in ep_loop_check_proc() just serves to prevent it from recursing too deeply while checking for loops. A more thorough check is done in reverse_path_check() after the new graph edge has already been created; this checks, among other things, that no paths going upwards from any non-epoll file with a length of more than 5 edges exist. However, this check does not apply to non-epoll files. As a result, it is possible to recurse to a depth of at least roughly 500, tested on v6.15. (I am unsure if deeper recursion is possible; and this may have changed with commit 8c44dac8add7 ("eventpoll: Fix priority inversion problem").) To fix it: 1. In ep_loop_check_proc(), note the subtree depth of each visited node, and use subtree depths for the total depth calculation even when a subtree has already been visited. 2. Add ep_get_upwards_depth_proc() for similarly determining the maximum depth of an upwards walk. 3. In ep_loop_check(), use these values to limit the total path length between epoll nodes to EP_MAX_NESTS edges.

In the Linux kernel, the following vulnerability has been resolved: fbdev: omapfb: Add 'plane' value check Function dispc_ovl_setup is not intended to work with the value OMAP_DSS_WB of the enum parameter plane. The value of this parameter is initialized in dss_init_overlays and in the current state of the code it cannot take this value so it's not a real problem. For the purposes of defensive coding it wouldn't be superfluous to check the parameter value, because some functions down the call stack process this value correctly and some not. For example, in dispc_ovl_setup_global_alpha it may lead to buffer overflow. Add check for this value. Found by Linux Verification Center (linuxtesting.org) with SVACE static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: vsock: fix recursive ->recvmsg calls After a vsock socket has been added to a BPF sockmap, its prot->recvmsg has been replaced with vsock_bpf_recvmsg(). Thus the following recursiion could happen: vsock_bpf_recvmsg() -> __vsock_recvmsg() -> vsock_connectible_recvmsg() -> prot->recvmsg() -> vsock_bpf_recvmsg() again We need to fix it by calling the original ->recvmsg() without any BPF sockmap logic in __vsock_recvmsg().

In the Linux kernel, the following vulnerability has been resolved: powercap: arm_scmi: Remove recursion while parsing zones Powercap zones can be defined as arranged in a hierarchy of trees and when registering a zone with powercap_register_zone(), the kernel powercap subsystem expects this to happen starting from the root zones down to the leaves; on the other side, de-registration by powercap_deregister_zone() must begin from the leaf zones. Available SCMI powercap zones are retrieved dynamically from the platform at probe time and, while any defined hierarchy between the zones is described properly in the zones descriptor, the platform returns the availables zones with no particular well-defined order: as a consequence, the trees possibly composing the hierarchy of zones have to be somehow walked properly to register the retrieved zones from the root. Currently the ARM SCMI Powercap driver walks the zones using a recursive algorithm; this approach, even though correct and tested can lead to kernel stack overflow when processing a returned hierarchy of zones composed by particularly high trees. Avoid possible kernel stack overflow by substituting the recursive approach with an iterative one supported by a dynamically allocated stack-like data structure.

In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Check for any of tcp_bpf_prots when cloning a listener A listening socket linked to a sockmap has its sk_prot overridden. It points to one of the struct proto variants in tcp_bpf_prots. The variant depends on the socket's family and which sockmap programs are attached. A child socket cloned from a TCP listener initially inherits their sk_prot. But before cloning is finished, we restore the child's proto to the listener's original non-tcp_bpf_prots one. This happens in tcp_create_openreq_child -> tcp_bpf_clone. Today, in tcp_bpf_clone we detect if the child's proto should be restored by checking only for the TCP_BPF_BASE proto variant. This is not correct. The sk_prot of listening socket linked to a sockmap can point to to any variant in tcp_bpf_prots. If the listeners sk_prot happens to be not the TCP_BPF_BASE variant, then the child socket unintentionally is left if the inherited sk_prot by tcp_bpf_clone. This leads to issues like infinite recursion on close [1], because the child state is otherwise not set up for use with tcp_bpf_prot operations. Adjust the check in tcp_bpf_clone to detect all of tcp_bpf_prots variants. Note that it wouldn't be sufficient to check the socket state when overriding the sk_prot in tcp_bpf_update_proto in order to always use the TCP_BPF_BASE variant for listening sockets. Since commit b8b8315e39ff ("bpf, sockmap: Remove unhash handler for BPF sockmap usage") it is possible for a socket to transition to TCP_LISTEN state while already linked to a sockmap, e.g. connect() -> insert into map -> connect(AF_UNSPEC) -> listen(). [1]: https://lore.kernel.org/all/00000000000073b14905ef2e7401@google.com/

In the Linux kernel, the following vulnerability has been resolved: scsi: target: Fix recursive locking in __configfs_open_file() In flush_write_buffer, &p->frag_sem is acquired and then the loaded store function is called, which, here, is target_core_item_dbroot_store(). This function called filp_open(), following which these functions were called (in reverse order), according to the call trace: down_read __configfs_open_file do_dentry_open vfs_open do_open path_openat do_filp_open file_open_name filp_open target_core_item_dbroot_store flush_write_buffer configfs_write_iter target_core_item_dbroot_store() tries to validate the new file path by trying to open the file path provided to it; however, in this case, the bug report shows: db_root: not a directory: /sys/kernel/config/target/dbroot indicating that the same configfs file was tried to be opened, on which it is currently working on. Thus, it is trying to acquire frag_sem semaphore of the same file of which it already holds the semaphore obtained in flush_write_buffer(), leading to acquiring the semaphore in a nested manner and a possibility of recursive locking. Fix this by modifying target_core_item_dbroot_store() to use kern_path() instead of filp_open() to avoid opening the file using filesystem-specific function __configfs_open_file(), and further modifying it to make this fix compatible.

In the Linux kernel, the following vulnerability has been resolved: riscv: VMAP_STACK overflow detection thread-safe commit 31da94c25aea ("riscv: add VMAP_STACK overflow detection") added support for CONFIG_VMAP_STACK. If overflow is detected, CPU switches to `shadow_stack` temporarily before switching finally to per-cpu `overflow_stack`. If two CPUs/harts are racing and end up in over flowing kernel stack, one or both will end up corrupting each other state because `shadow_stack` is not per-cpu. This patch optimizes per-cpu overflow stack switch by directly picking per-cpu `overflow_stack` and gets rid of `shadow_stack`. Following are the changes in this patch - Defines an asm macro to obtain per-cpu symbols in destination register. - In entry.S, when overflow is detected, per-cpu overflow stack is located using per-cpu asm macro. Computing per-cpu symbol requires a temporary register. x31 is saved away into CSR_SCRATCH (CSR_SCRATCH is anyways zero since we're in kernel). Please see Links for additional relevant disccussion and alternative solution. Tested by `echo EXHAUST_STACK > /sys/kernel/debug/provoke-crash/DIRECT` Kernel crash log below Insufficient stack space to handle exception!/debug/provoke-crash/DIRECT Task stack: [0xff20000010a98000..0xff20000010a9c000] Overflow stack: [0xff600001f7d98370..0xff600001f7d99370] CPU: 1 PID: 205 Comm: bash Not tainted 6.1.0-rc2-00001-g328a1f96f7b9 #34 Hardware name: riscv-virtio,qemu (DT) epc : __memset+0x60/0xfc ra : recursive_loop+0x48/0xc6 [lkdtm] epc : ffffffff808de0e4 ra : ffffffff0163a752 sp : ff20000010a97e80 gp : ffffffff815c0330 tp : ff600000820ea280 t0 : ff20000010a97e88 t1 : 000000000000002e t2 : 3233206874706564 s0 : ff20000010a982b0 s1 : 0000000000000012 a0 : ff20000010a97e88 a1 : 0000000000000000 a2 : 0000000000000400 a3 : ff20000010a98288 a4 : 0000000000000000 a5 : 0000000000000000 a6 : fffffffffffe43f0 a7 : 00007fffffffffff s2 : ff20000010a97e88 s3 : ffffffff01644680 s4 : ff20000010a9be90 s5 : ff600000842ba6c0 s6 : 00aaaaaac29e42b0 s7 : 00fffffff0aa3684 s8 : 00aaaaaac2978040 s9 : 0000000000000065 s10: 00ffffff8a7cad10 s11: 00ffffff8a76a4e0 t3 : ffffffff815dbaf4 t4 : ffffffff815dbaf4 t5 : ffffffff815dbab8 t6 : ff20000010a9bb48 status: 0000000200000120 badaddr: ff20000010a97e88 cause: 000000000000000f Kernel panic - not syncing: Kernel stack overflow CPU: 1 PID: 205 Comm: bash Not tainted 6.1.0-rc2-00001-g328a1f96f7b9 #34 Hardware name: riscv-virtio,qemu (DT) Call Trace: [<ffffffff80006754>] dump_backtrace+0x30/0x38 [<ffffffff808de798>] show_stack+0x40/0x4c [<ffffffff808ea2a8>] dump_stack_lvl+0x44/0x5c [<ffffffff808ea2d8>] dump_stack+0x18/0x20 [<ffffffff808dec06>] panic+0x126/0x2fe [<ffffffff800065ea>] walk_stackframe+0x0/0xf0 [<ffffffff0163a752>] recursive_loop+0x48/0xc6 [lkdtm] SMP: stopping secondary CPUs ---[ end Kernel panic - not syncing: Kernel stack overflow ]---

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix recvmsg() unconditional requeue If rxrpc_recvmsg() fails because MSG_DONTWAIT was specified but the call at the front of the recvmsg queue already has its mutex locked, it requeues the call - whether or not the call is already queued. The call may be on the queue because MSG_PEEK was also passed and so the call was not dequeued or because the I/O thread requeued it. The unconditional requeue may then corrupt the recvmsg queue, leading to things like UAFs or refcount underruns. Fix this by only requeuing the call if it isn't already on the queue - and moving it to the front if it is already queued. If we don't queue it, we have to put the ref we obtained by dequeuing it. Also, MSG_PEEK doesn't dequeue the call so shouldn't call rxrpc_notify_socket() for the call if we didn't use up all the data on the queue, so fix that also.

An issue was discovered in the Linux kernel before 5.8. lib/nlattr.c allows attackers to cause a denial of service (unbounded recursion) via a nested Netlink policy with a back reference.

In the Linux kernel, the following vulnerability has been resolved: arm64: Reserve an extra page for early kernel mapping The final part of [data, end) segment may overflow into the next page of init_pg_end[1] which is the gap page before early_init_stack[2]: [1] crash_arm64_v9.0.1> vtop ffffffed00601000 VIRTUAL PHYSICAL ffffffed00601000 83401000 PAGE DIRECTORY: ffffffecffd62000 PGD: ffffffecffd62da0 => 10000000833fb003 PMD: ffffff80033fb018 => 10000000833fe003 PTE: ffffff80033fe008 => 68000083401f03 PAGE: 83401000 PTE PHYSICAL FLAGS 68000083401f03 83401000 (VALID|SHARED|AF|NG|PXN|UXN) PAGE PHYSICAL MAPPING INDEX CNT FLAGS fffffffec00d0040 83401000 0 0 1 4000 reserved [2] ffffffed002c8000 (r) __pi__data ffffffed0054e000 (d) __pi___bss_start ffffffed005f5000 (b) __pi_init_pg_dir ffffffed005fe000 (b) __pi_init_pg_end ffffffed005ff000 (B) early_init_stack ffffffed00608000 (b) __pi__end For 4K pages, the early kernel mapping may use 2MB block entries but the kernel segments are only 64KB aligned. Segment boundaries that fall within a 2MB block therefore require a PTE table so that different attributes can be applied on either side of the boundary. KERNEL_SEGMENT_COUNT still correctly counts the five permanent kernel VMAs registered by declare_kernel_vmas(). However, since commit 5973a62efa34 ("arm64: map [_text, _stext) virtual address range non-executable+read-only"), the early mapper also maps [_text, _stext) separately from [_stext, _etext). This adds one more early-only split and can require one more page-table page than the existing EARLY_SEGMENT_EXTRA_PAGES allowance reserves. Increase the 4K-page early mapping allowance by one page to cover that additional split. [catalin.marinas@arm.com: rewrote part of the commit log] [catalin.marinas@arm.com: expanded the code comment]

check_input_term in sound/usb/mixer.c in the Linux kernel through 5.2.9 mishandles recursion, leading to kernel stack exhaustion.

In the Linux kernel, the following vulnerability has been resolved: rcu: Avoid stack overflow due to __rcu_irq_enter_check_tick() being kprobe-ed Registering a kprobe on __rcu_irq_enter_check_tick() can cause kernel stack overflow as shown below. This issue can be reproduced by enabling CONFIG_NO_HZ_FULL and booting the kernel with argument "nohz_full=", and then giving the following commands at the shell prompt: # cd /sys/kernel/tracing/ # echo 'p:mp1 __rcu_irq_enter_check_tick' >> kprobe_events # echo 1 > events/kprobes/enable This commit therefore adds __rcu_irq_enter_check_tick() to the kprobes blacklist using NOKPROBE_SYMBOL(). Insufficient stack space to handle exception! ESR: 0x00000000f2000004 -- BRK (AArch64) FAR: 0x0000ffffccf3e510 Task stack: [0xffff80000ad30000..0xffff80000ad38000] IRQ stack: [0xffff800008050000..0xffff800008058000] Overflow stack: [0xffff089c36f9f310..0xffff089c36fa0310] CPU: 5 PID: 190 Comm: bash Not tainted 6.2.0-rc2-00320-g1f5abbd77e2c #19 Hardware name: linux,dummy-virt (DT) pstate: 400003c5 (nZcv DAIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __rcu_irq_enter_check_tick+0x0/0x1b8 lr : ct_nmi_enter+0x11c/0x138 sp : ffff80000ad30080 x29: ffff80000ad30080 x28: ffff089c82e20000 x27: 0000000000000000 x26: 0000000000000000 x25: ffff089c02a8d100 x24: 0000000000000000 x23: 00000000400003c5 x22: 0000ffffccf3e510 x21: ffff089c36fae148 x20: ffff80000ad30120 x19: ffffa8da8fcce148 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: ffffa8da8e44ea6c x14: ffffa8da8e44e968 x13: ffffa8da8e03136c x12: 1fffe113804d6809 x11: ffff6113804d6809 x10: 0000000000000a60 x9 : dfff800000000000 x8 : ffff089c026b404f x7 : 00009eec7fb297f7 x6 : 0000000000000001 x5 : ffff80000ad30120 x4 : dfff800000000000 x3 : ffffa8da8e3016f4 x2 : 0000000000000003 x1 : 0000000000000000 x0 : 0000000000000000 Kernel panic - not syncing: kernel stack overflow CPU: 5 PID: 190 Comm: bash Not tainted 6.2.0-rc2-00320-g1f5abbd77e2c #19 Hardware name: linux,dummy-virt (DT) Call trace: dump_backtrace+0xf8/0x108 show_stack+0x20/0x30 dump_stack_lvl+0x68/0x84 dump_stack+0x1c/0x38 panic+0x214/0x404 add_taint+0x0/0xf8 panic_bad_stack+0x144/0x160 handle_bad_stack+0x38/0x58 __bad_stack+0x78/0x7c __rcu_irq_enter_check_tick+0x0/0x1b8 arm64_enter_el1_dbg.isra.0+0x14/0x20 el1_dbg+0x2c/0x90 el1h_64_sync_handler+0xcc/0xe8 el1h_64_sync+0x64/0x68 __rcu_irq_enter_check_tick+0x0/0x1b8 arm64_enter_el1_dbg.isra.0+0x14/0x20 el1_dbg+0x2c/0x90 el1h_64_sync_handler+0xcc/0xe8 el1h_64_sync+0x64/0x68 __rcu_irq_enter_check_tick+0x0/0x1b8 arm64_enter_el1_dbg.isra.0+0x14/0x20 el1_dbg+0x2c/0x90 el1h_64_sync_handler+0xcc/0xe8 el1h_64_sync+0x64/0x68 __rcu_irq_enter_check_tick+0x0/0x1b8 [...] el1_dbg+0x2c/0x90 el1h_64_sync_handler+0xcc/0xe8 el1h_64_sync+0x64/0x68 __rcu_irq_enter_check_tick+0x0/0x1b8 arm64_enter_el1_dbg.isra.0+0x14/0x20 el1_dbg+0x2c/0x90 el1h_64_sync_handler+0xcc/0xe8 el1h_64_sync+0x64/0x68 __rcu_irq_enter_check_tick+0x0/0x1b8 arm64_enter_el1_dbg.isra.0+0x14/0x20 el1_dbg+0x2c/0x90 el1h_64_sync_handler+0xcc/0xe8 el1h_64_sync+0x64/0x68 __rcu_irq_enter_check_tick+0x0/0x1b8 el1_interrupt+0x28/0x60 el1h_64_irq_handler+0x18/0x28 el1h_64_irq+0x64/0x68 __ftrace_set_clr_event_nolock+0x98/0x198 __ftrace_set_clr_event+0x58/0x80 system_enable_write+0x144/0x178 vfs_write+0x174/0x738 ksys_write+0xd0/0x188 __arm64_sys_write+0x4c/0x60 invoke_syscall+0x64/0x180 el0_svc_common.constprop.0+0x84/0x160 do_el0_svc+0x48/0xe8 el0_svc+0x34/0xd0 el0t_64_sync_handler+0xb8/0xc0 el0t_64_sync+0x190/0x194 SMP: stopping secondary CPUs Kernel Offset: 0x28da86000000 from 0xffff800008000000 PHYS_OFFSET: 0xfffff76600000000 CPU features: 0x00000,01a00100,0000421b Memory Limit: none

In the Linux kernel, the following vulnerability has been resolved: powerpc/perf: Optimize clearing the pending PMI and remove WARN_ON for PMI check in power_pmu_disable commit 2c9ac51b850d ("powerpc/perf: Fix PMU callbacks to clear pending PMI before resetting an overflown PMC") added a new function "pmi_irq_pending" in hw_irq.h. This function is to check if there is a PMI marked as pending in Paca (PACA_IRQ_PMI).This is used in power_pmu_disable in a WARN_ON. The intention here is to provide a warning if there is PMI pending, but no counter is found overflown. During some of the perf runs, below warning is hit: WARNING: CPU: 36 PID: 0 at arch/powerpc/perf/core-book3s.c:1332 power_pmu_disable+0x25c/0x2c0 Modules linked in: ----- NIP [c000000000141c3c] power_pmu_disable+0x25c/0x2c0 LR [c000000000141c8c] power_pmu_disable+0x2ac/0x2c0 Call Trace: [c000000baffcfb90] [c000000000141c8c] power_pmu_disable+0x2ac/0x2c0 (unreliable) [c000000baffcfc10] [c0000000003e2f8c] perf_pmu_disable+0x4c/0x60 [c000000baffcfc30] [c0000000003e3344] group_sched_out.part.124+0x44/0x100 [c000000baffcfc80] [c0000000003e353c] __perf_event_disable+0x13c/0x240 [c000000baffcfcd0] [c0000000003dd334] event_function+0xc4/0x140 [c000000baffcfd20] [c0000000003d855c] remote_function+0x7c/0xa0 [c000000baffcfd50] [c00000000026c394] flush_smp_call_function_queue+0xd4/0x300 [c000000baffcfde0] [c000000000065b24] smp_ipi_demux_relaxed+0xa4/0x100 [c000000baffcfe20] [c0000000000cb2b0] xive_muxed_ipi_action+0x20/0x40 [c000000baffcfe40] [c000000000207c3c] __handle_irq_event_percpu+0x8c/0x250 [c000000baffcfee0] [c000000000207e2c] handle_irq_event_percpu+0x2c/0xa0 [c000000baffcff10] [c000000000210a04] handle_percpu_irq+0x84/0xc0 [c000000baffcff40] [c000000000205f14] generic_handle_irq+0x54/0x80 [c000000baffcff60] [c000000000015740] __do_irq+0x90/0x1d0 [c000000baffcff90] [c000000000016990] __do_IRQ+0xc0/0x140 [c0000009732f3940] [c000000bafceaca8] 0xc000000bafceaca8 [c0000009732f39d0] [c000000000016b78] do_IRQ+0x168/0x1c0 [c0000009732f3a00] [c0000000000090c8] hardware_interrupt_common_virt+0x218/0x220 This means that there is no PMC overflown among the active events in the PMU, but there is a PMU pending in Paca. The function "any_pmc_overflown" checks the PMCs on active events in cpuhw->n_events. Code snippet: <<>> if (any_pmc_overflown(cpuhw)) clear_pmi_irq_pending(); else WARN_ON(pmi_irq_pending()); <<>> Here the PMC overflown is not from active event. Example: When we do perf record, default cycles and instructions will be running on PMC6 and PMC5 respectively. It could happen that overflowed event is currently not active and pending PMI is for the inactive event. Debug logs from trace_printk: <<>> any_pmc_overflown: idx is 5: pmc value is 0xd9a power_pmu_disable: PMC1: 0x0, PMC2: 0x0, PMC3: 0x0, PMC4: 0x0, PMC5: 0xd9a, PMC6: 0x80002011 <<>> Here active PMC (from idx) is PMC5 , but overflown PMC is PMC6(0x80002011). When we handle PMI interrupt for such cases, if the PMC overflown is from inactive event, it will be ignored. Reference commit: commit bc09c219b2e6 ("powerpc/perf: Fix finding overflowed PMC in interrupt") Patch addresses two changes: 1) Fix 1 : Removal of warning ( WARN_ON(pmi_irq_pending()); ) We were printing warning if no PMC is found overflown among active PMU events, but PMI pending in PACA. But this could happen in cases where PMC overflown is not in active PMC. An inactive event could have caused the overflow. Hence the warning is not needed. To know pending PMI is from an inactive event, we need to loop through all PMC's which will cause more SPR reads via mfspr and increase in context switch. Also in existing function: perf_event_interrupt, already we ignore PMI's overflown when it is from an inactive PMC. 2) Fix 2: optimization in clearing pending PMI. Currently we check for any active PMC overflown before clearing PMI pending in Paca. This is causing additional SP ---truncated---

In the Linux kernel, the following vulnerability has been resolved: crypto: hisilicon/qm - increase the memory of local variables Increase the buffer to prevent stack overflow by fuzz test. The maximum length of the qos configuration buffer is 256 bytes. Currently, the value of the 'val buffer' is only 32 bytes. The sscanf does not check the dest memory length. So the 'val buffer' may stack overflow.

In the Linux kernel, the following vulnerability has been resolved: perf: Improve missing SIGTRAP checking To catch missing SIGTRAP we employ a WARN in __perf_event_overflow(), which fires if pending_sigtrap was already set: returning to user space without consuming pending_sigtrap, and then having the event fire again would re-enter the kernel and trigger the WARN. This, however, seemed to miss the case where some events not associated with progress in the user space task can fire and the interrupt handler runs before the IRQ work meant to consume pending_sigtrap (and generate the SIGTRAP). syzbot gifted us this stack trace: | WARNING: CPU: 0 PID: 3607 at kernel/events/core.c:9313 __perf_event_overflow | Modules linked in: | CPU: 0 PID: 3607 Comm: syz-executor100 Not tainted 6.1.0-rc2-syzkaller-00073-g88619e77b33d #0 | Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/11/2022 | RIP: 0010:__perf_event_overflow+0x498/0x540 kernel/events/core.c:9313 | <...> | Call Trace: | <TASK> | perf_swevent_hrtimer+0x34f/0x3c0 kernel/events/core.c:10729 | __run_hrtimer kernel/time/hrtimer.c:1685 [inline] | __hrtimer_run_queues+0x1c6/0xfb0 kernel/time/hrtimer.c:1749 | hrtimer_interrupt+0x31c/0x790 kernel/time/hrtimer.c:1811 | local_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1096 [inline] | __sysvec_apic_timer_interrupt+0x17c/0x640 arch/x86/kernel/apic/apic.c:1113 | sysvec_apic_timer_interrupt+0x40/0xc0 arch/x86/kernel/apic/apic.c:1107 | asm_sysvec_apic_timer_interrupt+0x16/0x20 arch/x86/include/asm/idtentry.h:649 | <...> | </TASK> In this case, syzbot produced a program with event type PERF_TYPE_SOFTWARE and config PERF_COUNT_SW_CPU_CLOCK. The hrtimer manages to fire again before the IRQ work got a chance to run, all while never having returned to user space. Improve the WARN to check for real progress in user space: approximate this by storing a 32-bit hash of the current IP into pending_sigtrap, and if an event fires while pending_sigtrap still matches the previous IP, we assume no progress (false negatives are possible given we could return to user space and trigger again on the same IP).

In the Linux kernel, the following vulnerability has been resolved: vxlan: Fix NPD in {arp,neigh}_reduce() when using nexthop objects When the "proxy" option is enabled on a VXLAN device, the device will suppress ARP requests and IPv6 Neighbor Solicitation messages if it is able to reply on behalf of the remote host. That is, if a matching and valid neighbor entry is configured on the VXLAN device whose MAC address is not behind the "any" remote (0.0.0.0 / ::). The code currently assumes that the FDB entry for the neighbor's MAC address points to a valid remote destination, but this is incorrect if the entry is associated with an FDB nexthop group. This can result in a NPD [1][3] which can be reproduced using [2][4]. Fix by checking that the remote destination exists before dereferencing it. [1] BUG: kernel NULL pointer dereference, address: 0000000000000000 [...] CPU: 4 UID: 0 PID: 365 Comm: arping Not tainted 6.17.0-rc2-virtme-g2a89cb21162c #2 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014 RIP: 0010:vxlan_xmit+0xb58/0x15f0 [...] Call Trace: <TASK> dev_hard_start_xmit+0x5d/0x1c0 __dev_queue_xmit+0x246/0xfd0 packet_sendmsg+0x113a/0x1850 __sock_sendmsg+0x38/0x70 __sys_sendto+0x126/0x180 __x64_sys_sendto+0x24/0x30 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x4b/0x53 [2] #!/bin/bash ip address add 192.0.2.1/32 dev lo ip nexthop add id 1 via 192.0.2.2 fdb ip nexthop add id 10 group 1 fdb ip link add name vx0 up type vxlan id 10010 local 192.0.2.1 dstport 4789 proxy ip neigh add 192.0.2.3 lladdr 00:11:22:33:44:55 nud perm dev vx0 bridge fdb add 00:11:22:33:44:55 dev vx0 self static nhid 10 arping -b -c 1 -s 192.0.2.1 -I vx0 192.0.2.3 [3] BUG: kernel NULL pointer dereference, address: 0000000000000000 [...] CPU: 13 UID: 0 PID: 372 Comm: ndisc6 Not tainted 6.17.0-rc2-virtmne-g6ee90cb26014 #3 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1v996), BIOS 1.17.0-4.fc41 04/01/2x014 RIP: 0010:vxlan_xmit+0x803/0x1600 [...] Call Trace: <TASK> dev_hard_start_xmit+0x5d/0x1c0 __dev_queue_xmit+0x246/0xfd0 ip6_finish_output2+0x210/0x6c0 ip6_finish_output+0x1af/0x2b0 ip6_mr_output+0x92/0x3e0 ip6_send_skb+0x30/0x90 rawv6_sendmsg+0xe6e/0x12e0 __sock_sendmsg+0x38/0x70 __sys_sendto+0x126/0x180 __x64_sys_sendto+0x24/0x30 do_syscall_64+0xa4/0x260 entry_SYSCALL_64_after_hwframe+0x4b/0x53 RIP: 0033:0x7f383422ec77 [4] #!/bin/bash ip address add 2001:db8:1::1/128 dev lo ip nexthop add id 1 via 2001:db8:1::1 fdb ip nexthop add id 10 group 1 fdb ip link add name vx0 up type vxlan id 10010 local 2001:db8:1::1 dstport 4789 proxy ip neigh add 2001:db8:1::3 lladdr 00:11:22:33:44:55 nud perm dev vx0 bridge fdb add 00:11:22:33:44:55 dev vx0 self static nhid 10 ndisc6 -r 1 -s 2001:db8:1::1 -w 1 2001:db8:1::3 vx0

In the Linux kernel, the following vulnerability has been resolved: drm/i915/active: Fix misuse of non-idle barriers as fence trackers Users reported oopses on list corruptions when using i915 perf with a number of concurrently running graphics applications. Root cause analysis pointed at an issue in barrier processing code -- a race among perf open / close replacing active barriers with perf requests on kernel context and concurrent barrier preallocate / acquire operations performed during user context first pin / last unpin. When adding a request to a composite tracker, we try to reuse an existing fence tracker, already allocated and registered with that composite. The tracker we obtain may already track another fence, may be an idle barrier, or an active barrier. If the tracker we get occurs a non-idle barrier then we try to delete that barrier from a list of barrier tasks it belongs to. However, while doing that we don't respect return value from a function that performs the barrier deletion. Should the deletion ever fail, we would end up reusing the tracker still registered as a barrier task. Since the same structure field is reused with both fence callback lists and barrier tasks list, list corruptions would likely occur. Barriers are now deleted from a barrier tasks list by temporarily removing the list content, traversing that content with skip over the node to be deleted, then populating the list back with the modified content. Should that intentionally racy concurrent deletion attempts be not serialized, one or more of those may fail because of the list being temporary empty. Related code that ignores the results of barrier deletion was initially introduced in v5.4 by commit d8af05ff38ae ("drm/i915: Allow sharing the idle-barrier from other kernel requests"). However, all users of the barrier deletion routine were apparently serialized at that time, then the issue didn't exhibit itself. Results of git bisect with help of a newly developed igt@gem_barrier_race@remote-request IGT test indicate that list corruptions might start to appear after commit 311770173fac ("drm/i915/gt: Schedule request retirement when timeline idles"), introduced in v5.5. Respect results of barrier deletion attempts -- mark the barrier as idle only if successfully deleted from the list. Then, before proceeding with setting our fence as the one currently tracked, make sure that the tracker we've got is not a non-idle barrier. If that check fails then don't use that tracker but go back and try to acquire a new, usable one. v3: use unlikely() to document what outcome we expect (Andi), - fix bad grammar in commit description. v2: no code changes, - blame commit 311770173fac ("drm/i915/gt: Schedule request retirement when timeline idles"), v5.5, not commit d8af05ff38ae ("drm/i915: Allow sharing the idle-barrier from other kernel requests"), v5.4, - reword commit description. (cherry picked from commit 506006055769b10d1b2b4e22f636f3b45e0e9fc7)

In the Linux kernel, the following vulnerability has been resolved: mptcp: pm: fix UaF read in mptcp_pm_nl_rm_addr_or_subflow Syzkaller reported this splat: ================================================================== BUG: KASAN: slab-use-after-free in mptcp_pm_nl_rm_addr_or_subflow+0xb44/0xcc0 net/mptcp/pm_netlink.c:881 Read of size 4 at addr ffff8880569ac858 by task syz.1.2799/14662 CPU: 0 UID: 0 PID: 14662 Comm: syz.1.2799 Not tainted 6.12.0-rc2-syzkaller-00307-g36c254515dc6 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120 print_address_description mm/kasan/report.c:377 [inline] print_report+0xc3/0x620 mm/kasan/report.c:488 kasan_report+0xd9/0x110 mm/kasan/report.c:601 mptcp_pm_nl_rm_addr_or_subflow+0xb44/0xcc0 net/mptcp/pm_netlink.c:881 mptcp_pm_nl_rm_subflow_received net/mptcp/pm_netlink.c:914 [inline] mptcp_nl_remove_id_zero_address+0x305/0x4a0 net/mptcp/pm_netlink.c:1572 mptcp_pm_nl_del_addr_doit+0x5c9/0x770 net/mptcp/pm_netlink.c:1603 genl_family_rcv_msg_doit+0x202/0x2f0 net/netlink/genetlink.c:1115 genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline] genl_rcv_msg+0x565/0x800 net/netlink/genetlink.c:1210 netlink_rcv_skb+0x165/0x410 net/netlink/af_netlink.c:2551 genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219 netlink_unicast_kernel net/netlink/af_netlink.c:1331 [inline] netlink_unicast+0x53c/0x7f0 net/netlink/af_netlink.c:1357 netlink_sendmsg+0x8b8/0xd70 net/netlink/af_netlink.c:1901 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg net/socket.c:744 [inline] ____sys_sendmsg+0x9ae/0xb40 net/socket.c:2607 ___sys_sendmsg+0x135/0x1e0 net/socket.c:2661 __sys_sendmsg+0x117/0x1f0 net/socket.c:2690 do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline] __do_fast_syscall_32+0x73/0x120 arch/x86/entry/common.c:386 do_fast_syscall_32+0x32/0x80 arch/x86/entry/common.c:411 entry_SYSENTER_compat_after_hwframe+0x84/0x8e RIP: 0023:0xf7fe4579 Code: b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d b4 26 00 00 00 00 8d b4 26 00 00 00 00 RSP: 002b:00000000f574556c EFLAGS: 00000296 ORIG_RAX: 0000000000000172 RAX: ffffffffffffffda RBX: 000000000000000b RCX: 0000000020000140 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000296 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> Allocated by task 5387: kasan_save_stack+0x33/0x60 mm/kasan/common.c:47 kasan_save_track+0x14/0x30 mm/kasan/common.c:68 poison_kmalloc_redzone mm/kasan/common.c:377 [inline] __kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:394 kmalloc_noprof include/linux/slab.h:878 [inline] kzalloc_noprof include/linux/slab.h:1014 [inline] subflow_create_ctx+0x87/0x2a0 net/mptcp/subflow.c:1803 subflow_ulp_init+0xc3/0x4d0 net/mptcp/subflow.c:1956 __tcp_set_ulp net/ipv4/tcp_ulp.c:146 [inline] tcp_set_ulp+0x326/0x7f0 net/ipv4/tcp_ulp.c:167 mptcp_subflow_create_socket+0x4ae/0x10a0 net/mptcp/subflow.c:1764 __mptcp_subflow_connect+0x3cc/0x1490 net/mptcp/subflow.c:1592 mptcp_pm_create_subflow_or_signal_addr+0xbda/0x23a0 net/mptcp/pm_netlink.c:642 mptcp_pm_nl_fully_established net/mptcp/pm_netlink.c:650 [inline] mptcp_pm_nl_work+0x3a1/0x4f0 net/mptcp/pm_netlink.c:943 mptcp_worker+0x15a/0x1240 net/mptcp/protocol.c:2777 process_one_work+0x958/0x1b30 kernel/workqueue.c:3229 process_scheduled_works kernel/workqueue.c:3310 [inline] worker_thread+0x6c8/0xf00 kernel/workqueue.c:3391 kthread+0x2c1/0x3a0 kernel/kthread.c:389 ret_from_fork+0x45/0x80 arch/x86/ke ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: ath9k: hif_usb: fix memory leak of remain_skbs hif_dev->remain_skb is allocated and used exclusively in ath9k_hif_usb_rx_stream(). It is implied that an allocated remain_skb is processed and subsequently freed (in error paths) only during the next call of ath9k_hif_usb_rx_stream(). So, if the urbs are deallocated between those two calls due to the device deinitialization or suspend, it is possible that ath9k_hif_usb_rx_stream() is not called next time and the allocated remain_skb is leaked. Our local Syzkaller instance was able to trigger that. remain_skb makes sense when receiving two consecutive urbs which are logically linked together, i.e. a specific data field from the first skb indicates a cached skb to be allocated, memcpy'd with some data and subsequently processed in the next call to ath9k_hif_usb_rx_stream(). Urbs deallocation supposedly makes that link irrelevant so we need to free the cached skb in those cases. Fix the leak by introducing a function to explicitly free remain_skb (if it is not NULL) when the rx urbs have been deallocated. remain_skb is NULL when it has not been allocated at all (hif_dev struct is kzalloced) or when it has been processed in next call to ath9k_hif_usb_rx_stream(). Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: skmsg: Skip zero length skb in sk_msg_recvmsg When running BPF selftests (./test_progs -t sockmap_basic) on a Loongarch platform, the following kernel panic occurs: [...] Oops[#1]: CPU: 22 PID: 2824 Comm: test_progs Tainted: G OE 6.10.0-rc2+ #18 Hardware name: LOONGSON Dabieshan/Loongson-TC542F0, BIOS Loongson-UDK2018 ... ... ra: 90000000048bf6c0 sk_msg_recvmsg+0x120/0x560 ERA: 9000000004162774 copy_page_to_iter+0x74/0x1c0 CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE) PRMD: 0000000c (PPLV0 +PIE +PWE) EUEN: 00000007 (+FPE +SXE +ASXE -BTE) ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7) ESTAT: 00010000 [PIL] (IS= ECode=1 EsubCode=0) BADV: 0000000000000040 PRID: 0014c011 (Loongson-64bit, Loongson-3C5000) Modules linked in: bpf_testmod(OE) xt_CHECKSUM xt_MASQUERADE xt_conntrack Process test_progs (pid: 2824, threadinfo=0000000000863a31, task=...) Stack : ... Call Trace: [<9000000004162774>] copy_page_to_iter+0x74/0x1c0 [<90000000048bf6c0>] sk_msg_recvmsg+0x120/0x560 [<90000000049f2b90>] tcp_bpf_recvmsg_parser+0x170/0x4e0 [<90000000049aae34>] inet_recvmsg+0x54/0x100 [<900000000481ad5c>] sock_recvmsg+0x7c/0xe0 [<900000000481e1a8>] __sys_recvfrom+0x108/0x1c0 [<900000000481e27c>] sys_recvfrom+0x1c/0x40 [<9000000004c076ec>] do_syscall+0x8c/0xc0 [<9000000003731da4>] handle_syscall+0xc4/0x160 Code: ... ---[ end trace 0000000000000000 ]--- Kernel panic - not syncing: Fatal exception Kernel relocated by 0x3510000 .text @ 0x9000000003710000 .data @ 0x9000000004d70000 .bss @ 0x9000000006469400 ---[ end Kernel panic - not syncing: Fatal exception ]--- [...] This crash happens every time when running sockmap_skb_verdict_shutdown subtest in sockmap_basic. This crash is because a NULL pointer is passed to page_address() in the sk_msg_recvmsg(). Due to the different implementations depending on the architecture, page_address(NULL) will trigger a panic on Loongarch platform but not on x86 platform. So this bug was hidden on x86 platform for a while, but now it is exposed on Loongarch platform. The root cause is that a zero length skb (skb->len == 0) was put on the queue. This zero length skb is a TCP FIN packet, which was sent by shutdown(), invoked in test_sockmap_skb_verdict_shutdown(): shutdown(p1, SHUT_WR); In this case, in sk_psock_skb_ingress_enqueue(), num_sge is zero, and no page is put to this sge (see sg_set_page in sg_set_page), but this empty sge is queued into ingress_msg list. And in sk_msg_recvmsg(), this empty sge is used, and a NULL page is got by sg_page(sge). Pass this NULL page to copy_page_to_iter(), which passes it to kmap_local_page() and to page_address(), then kernel panics. To solve this, we should skip this zero length skb. So in sk_msg_recvmsg(), if copy is zero, that means it's a zero length skb, skip invoking copy_page_to_iter(). We are using the EFAULT return triggered by copy_page_to_iter to check for is_fin in tcp_bpf.c.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: remove unreasonable unlock in ocfs2_read_blocks Patch series "Misc fixes for ocfs2_read_blocks", v5. This series contains 2 fixes for ocfs2_read_blocks(). The first patch fix the issue reported by syzbot, which detects bad unlock balance in ocfs2_read_blocks(). The second patch fixes an issue reported by Heming Zhao when reviewing above fix. This patch (of 2): There was a lock release before exiting, so remove the unreasonable unlock.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/gfx9: Add Cleaner Shader Deinitialization in gfx_v9_0 Module This commit addresses an omission in the previous patch related to the cleaner shader support for GFX9 hardware. Specifically, it adds the necessary deinitialization code for the cleaner shader in the gfx_v9_0_sw_fini function. The added line amdgpu_gfx_cleaner_shader_sw_fini(adev); ensures that any allocated resources for the cleaner shader are freed correctly, avoiding potential memory leaks and ensuring that the GPU state is clean for the next initialization sequence.

In the Linux kernel, the following vulnerability has been resolved: drm/xe: Fix fault on fd close after unbind If userspace holds an fd open, unbinds the device and then closes it, the driver shouldn't try to access the hardware. Protect it by using drm_dev_enter()/drm_dev_exit(). This fixes the following page fault: <6> [IGT] xe_wedged: exiting, ret=98 <1> BUG: unable to handle page fault for address: ffffc901bc5e508c <1> #PF: supervisor read access in kernel mode <1> #PF: error_code(0x0000) - not-present page ... <4> xe_lrc_update_timestamp+0x1c/0xd0 [xe] <4> xe_exec_queue_update_run_ticks+0x50/0xb0 [xe] <4> xe_exec_queue_fini+0x16/0xb0 [xe] <4> __guc_exec_queue_fini_async+0xc4/0x190 [xe] <4> guc_exec_queue_fini_async+0xa0/0xe0 [xe] <4> guc_exec_queue_fini+0x23/0x40 [xe] <4> xe_exec_queue_destroy+0xb3/0xf0 [xe] <4> xe_file_close+0xd4/0x1a0 [xe] <4> drm_file_free+0x210/0x280 [drm] <4> drm_close_helper.isra.0+0x6d/0x80 [drm] <4> drm_release_noglobal+0x20/0x90 [drm] (cherry picked from commit 4ca1fd418338d4d135428a0eb1e16e3b3ce17ee8)

In the Linux kernel, the following vulnerability has been resolved: ksmbd: discard write access to the directory open may_open() does not allow a directory to be opened with the write access. However, some writing flags set by client result in adding write access on server, making ksmbd incompatible with FUSE file system. Simply, let's discard the write access when opening a directory. list_add corruption. next is NULL. ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:26! pc : __list_add_valid+0x88/0xbc lr : __list_add_valid+0x88/0xbc Call trace: __list_add_valid+0x88/0xbc fuse_finish_open+0x11c/0x170 fuse_open_common+0x284/0x5e8 fuse_dir_open+0x14/0x24 do_dentry_open+0x2a4/0x4e0 dentry_open+0x50/0x80 smb2_open+0xbe4/0x15a4 handle_ksmbd_work+0x478/0x5ec process_one_work+0x1b4/0x448 worker_thread+0x25c/0x430 kthread+0x104/0x1d4 ret_from_fork+0x10/0x20

In the Linux kernel, the following vulnerability has been resolved: mm: hugetlb: independent PMD page table shared count The folio refcount may be increased unexpectly through try_get_folio() by caller such as split_huge_pages. In huge_pmd_unshare(), we use refcount to check whether a pmd page table is shared. The check is incorrect if the refcount is increased by the above caller, and this can cause the page table leaked: BUG: Bad page state in process sh pfn:109324 page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x66 pfn:0x109324 flags: 0x17ffff800000000(node=0|zone=2|lastcpupid=0xfffff) page_type: f2(table) raw: 017ffff800000000 0000000000000000 0000000000000000 0000000000000000 raw: 0000000000000066 0000000000000000 00000000f2000000 0000000000000000 page dumped because: nonzero mapcount ... CPU: 31 UID: 0 PID: 7515 Comm: sh Kdump: loaded Tainted: G B 6.13.0-rc2master+ #7 Tainted: [B]=BAD_PAGE Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 Call trace: show_stack+0x20/0x38 (C) dump_stack_lvl+0x80/0xf8 dump_stack+0x18/0x28 bad_page+0x8c/0x130 free_page_is_bad_report+0xa4/0xb0 free_unref_page+0x3cc/0x620 __folio_put+0xf4/0x158 split_huge_pages_all+0x1e0/0x3e8 split_huge_pages_write+0x25c/0x2d8 full_proxy_write+0x64/0xd8 vfs_write+0xcc/0x280 ksys_write+0x70/0x110 __arm64_sys_write+0x24/0x38 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0xc8/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x34/0x128 el0t_64_sync_handler+0xc8/0xd0 el0t_64_sync+0x190/0x198 The issue may be triggered by damon, offline_page, page_idle, etc, which will increase the refcount of page table. 1. The page table itself will be discarded after reporting the "nonzero mapcount". 2. The HugeTLB page mapped by the page table miss freeing since we treat the page table as shared and a shared page table will not be unmapped. Fix it by introducing independent PMD page table shared count. As described by comment, pt_index/pt_mm/pt_frag_refcount are used for s390 gmap, x86 pgds and powerpc, pt_share_count is used for x86/arm64/riscv pmds, so we can reuse the field as pt_share_count.

In the Linux kernel, the following vulnerability has been resolved: bpf: bpf_local_storage: Always use bpf_mem_alloc in PREEMPT_RT In PREEMPT_RT, kmalloc(GFP_ATOMIC) is still not safe in non preemptible context. bpf_mem_alloc must be used in PREEMPT_RT. This patch is to enforce bpf_mem_alloc in the bpf_local_storage when CONFIG_PREEMPT_RT is enabled. [ 35.118559] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 [ 35.118566] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1832, name: test_progs [ 35.118569] preempt_count: 1, expected: 0 [ 35.118571] RCU nest depth: 1, expected: 1 [ 35.118577] INFO: lockdep is turned off. ... [ 35.118647] __might_resched+0x433/0x5b0 [ 35.118677] rt_spin_lock+0xc3/0x290 [ 35.118700] ___slab_alloc+0x72/0xc40 [ 35.118723] __kmalloc_noprof+0x13f/0x4e0 [ 35.118732] bpf_map_kzalloc+0xe5/0x220 [ 35.118740] bpf_selem_alloc+0x1d2/0x7b0 [ 35.118755] bpf_local_storage_update+0x2fa/0x8b0 [ 35.118784] bpf_sk_storage_get_tracing+0x15a/0x1d0 [ 35.118791] bpf_prog_9a118d86fca78ebb_trace_inet_sock_set_state+0x44/0x66 [ 35.118795] bpf_trace_run3+0x222/0x400 [ 35.118820] __bpf_trace_inet_sock_set_state+0x11/0x20 [ 35.118824] trace_inet_sock_set_state+0x112/0x130 [ 35.118830] inet_sk_state_store+0x41/0x90 [ 35.118836] tcp_set_state+0x3b3/0x640 There is no need to adjust the gfp_flags passing to the bpf_mem_cache_alloc_flags() which only honors the GFP_KERNEL. The verifier has ensured GFP_KERNEL is passed only in sleepable context. It has been an old issue since the first introduction of the bpf_local_storage ~5 years ago, so this patch targets the bpf-next. bpf_mem_alloc is needed to solve it, so the Fixes tag is set to the commit when bpf_mem_alloc was first used in the bpf_local_storage.

In the Linux kernel, the following vulnerability has been resolved: bpf: check changes_pkt_data property for extension programs When processing calls to global sub-programs, verifier decides whether to invalidate all packet pointers in current state depending on the changes_pkt_data property of the global sub-program. Because of this, an extension program replacing a global sub-program must be compatible with changes_pkt_data property of the sub-program being replaced. This commit: - adds changes_pkt_data flag to struct bpf_prog_aux: - this flag is set in check_cfg() for main sub-program; - in jit_subprogs() for other sub-programs; - modifies bpf_check_attach_btf_id() to check changes_pkt_data flag; - moves call to check_attach_btf_id() after the call to check_cfg(), because it needs changes_pkt_data flag to be set: bpf_check: ... ... - check_attach_btf_id resolve_pseudo_ldimm64 resolve_pseudo_ldimm64 --> bpf_prog_is_offloaded bpf_prog_is_offloaded check_cfg check_cfg + check_attach_btf_id ... ... The following fields are set by check_attach_btf_id(): - env->ops - prog->aux->attach_btf_trace - prog->aux->attach_func_name - prog->aux->attach_func_proto - prog->aux->dst_trampoline - prog->aux->mod - prog->aux->saved_dst_attach_type - prog->aux->saved_dst_prog_type - prog->expected_attach_type Neither of these fields are used by resolve_pseudo_ldimm64() or bpf_prog_offload_verifier_prep() (for netronome and netdevsim drivers), so the reordering is safe.

In the Linux kernel, the following vulnerability has been resolved: riscv: mm: Do not call pmd dtor on vmemmap page table teardown The vmemmap's, which is used for RV64 with SPARSEMEM_VMEMMAP, page tables are populated using pmd (page middle directory) hugetables. However, the pmd allocation is not using the generic mechanism used by the VMA code (e.g. pmd_alloc()), or the RISC-V specific create_pgd_mapping()/alloc_pmd_late(). Instead, the vmemmap page table code allocates a page, and calls vmemmap_set_pmd(). This results in that the pmd ctor is *not* called, nor would it make sense to do so. Now, when tearing down a vmemmap page table pmd, the cleanup code would unconditionally, and incorrectly call the pmd dtor, which results in a crash (best case). This issue was found when running the HMM selftests: | tools/testing/selftests/mm# ./test_hmm.sh smoke | ... # when unloading the test_hmm.ko module | page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x10915b | flags: 0x1000000000000000(node=0|zone=1) | raw: 1000000000000000 0000000000000000 dead000000000122 0000000000000000 | raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000 | page dumped because: VM_BUG_ON_PAGE(ptdesc->pmd_huge_pte) | ------------[ cut here ]------------ | kernel BUG at include/linux/mm.h:3080! | Kernel BUG [#1] | Modules linked in: test_hmm(-) sch_fq_codel fuse drm drm_panel_orientation_quirks backlight dm_mod | CPU: 1 UID: 0 PID: 514 Comm: modprobe Tainted: G W 6.12.0-00982-gf2a4f1682d07 #2 | Tainted: [W]=WARN | Hardware name: riscv-virtio qemu/qemu, BIOS 2024.10 10/01/2024 | epc : remove_pgd_mapping+0xbec/0x1070 | ra : remove_pgd_mapping+0xbec/0x1070 | epc : ffffffff80010a68 ra : ffffffff80010a68 sp : ff20000000a73940 | gp : ffffffff827b2d88 tp : ff6000008785da40 t0 : ffffffff80fbce04 | t1 : 0720072007200720 t2 : 706d756420656761 s0 : ff20000000a73a50 | s1 : ff6000008915cff8 a0 : 0000000000000039 a1 : 0000000000000008 | a2 : ff600003fff0de20 a3 : 0000000000000000 a4 : 0000000000000000 | a5 : 0000000000000000 a6 : c0000000ffffefff a7 : ffffffff824469b8 | s2 : ff1c0000022456c0 s3 : ff1ffffffdbfffff s4 : ff6000008915c000 | s5 : ff6000008915c000 s6 : ff6000008915c000 s7 : ff1ffffffdc00000 | s8 : 0000000000000001 s9 : ff1ffffffdc00000 s10: ffffffff819a31f0 | s11: ffffffffffffffff t3 : ffffffff8000c950 t4 : ff60000080244f00 | t5 : ff60000080244000 t6 : ff20000000a73708 | status: 0000000200000120 badaddr: ffffffff80010a68 cause: 0000000000000003 | [<ffffffff80010a68>] remove_pgd_mapping+0xbec/0x1070 | [<ffffffff80fd238e>] vmemmap_free+0x14/0x1e | [<ffffffff8032e698>] section_deactivate+0x220/0x452 | [<ffffffff8032ef7e>] sparse_remove_section+0x4a/0x58 | [<ffffffff802f8700>] __remove_pages+0x7e/0xba | [<ffffffff803760d8>] memunmap_pages+0x2bc/0x3fe | [<ffffffff02a3ca28>] dmirror_device_remove_chunks+0x2ea/0x518 [test_hmm] | [<ffffffff02a3e026>] hmm_dmirror_exit+0x3e/0x1018 [test_hmm] | [<ffffffff80102c14>] __riscv_sys_delete_module+0x15a/0x2a6 | [<ffffffff80fd020c>] do_trap_ecall_u+0x1f2/0x266 | [<ffffffff80fde0a2>] _new_vmalloc_restore_context_a0+0xc6/0xd2 | Code: bf51 7597 0184 8593 76a5 854a 4097 0029 80e7 2c00 (9002) 7597 | ---[ end trace 0000000000000000 ]--- | Kernel panic - not syncing: Fatal exception in interrupt Add a check to avoid calling the pmd dtor, if the calling context is vmemmap_free().

In the Linux kernel, the following vulnerability has been resolved: vmxnet3: Fix packet corruption in vmxnet3_xdp_xmit_frame Andrew and Nikolay reported connectivity issues with Cilium's service load-balancing in case of vmxnet3. If a BPF program for native XDP adds an encapsulation header such as IPIP and transmits the packet out the same interface, then in case of vmxnet3 a corrupted packet is being sent and subsequently dropped on the path. vmxnet3_xdp_xmit_frame() which is called e.g. via vmxnet3_run_xdp() through vmxnet3_xdp_xmit_back() calculates an incorrect DMA address: page = virt_to_page(xdpf->data); tbi->dma_addr = page_pool_get_dma_addr(page) + VMXNET3_XDP_HEADROOM; dma_sync_single_for_device(&adapter->pdev->dev, tbi->dma_addr, buf_size, DMA_TO_DEVICE); The above assumes a fixed offset (VMXNET3_XDP_HEADROOM), but the XDP BPF program could have moved xdp->data. While the passed buf_size is correct (xdpf->len), the dma_addr needs to have a dynamic offset which can be calculated as xdpf->data - (void *)xdpf, that is, xdp->data - xdp->data_hard_start.

In the Linux kernel, the following vulnerability has been resolved: mfd: intel_soc_pmic_bxtwc: Use IRQ domain for USB Type-C device While design wise the idea of converting the driver to use the hierarchy of the IRQ chips is correct, the implementation has (inherited) flaws. This was unveiled when platform_get_irq() had started WARN() on IRQ 0 that is supposed to be a Linux IRQ number (also known as vIRQ). Rework the driver to respect IRQ domain when creating each MFD device separately, as the domain is not the same for all of them.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix cpu stuck caused by printings during reset During reset, cmd to destroy resources such as qp, cq, and mr may fail, and error logs will be printed. When a large number of resources are destroyed, there will be lots of printings, and it may lead to a cpu stuck. Delete some unnecessary printings and replace other printing functions in these paths with the ratelimited version.

In the Linux kernel, the following vulnerability has been resolved: netrom: check buffer length before accessing it Syzkaller reports an uninit value read from ax25cmp when sending raw message through ieee802154 implementation. ===================================================== BUG: KMSAN: uninit-value in ax25cmp+0x3a5/0x460 net/ax25/ax25_addr.c:119 ax25cmp+0x3a5/0x460 net/ax25/ax25_addr.c:119 nr_dev_get+0x20e/0x450 net/netrom/nr_route.c:601 nr_route_frame+0x1a2/0xfc0 net/netrom/nr_route.c:774 nr_xmit+0x5a/0x1c0 net/netrom/nr_dev.c:144 __netdev_start_xmit include/linux/netdevice.h:4940 [inline] netdev_start_xmit include/linux/netdevice.h:4954 [inline] xmit_one net/core/dev.c:3548 [inline] dev_hard_start_xmit+0x247/0xa10 net/core/dev.c:3564 __dev_queue_xmit+0x33b8/0x5130 net/core/dev.c:4349 dev_queue_xmit include/linux/netdevice.h:3134 [inline] raw_sendmsg+0x654/0xc10 net/ieee802154/socket.c:299 ieee802154_sock_sendmsg+0x91/0xc0 net/ieee802154/socket.c:96 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] ____sys_sendmsg+0x9c2/0xd60 net/socket.c:2584 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2638 __sys_sendmsg net/socket.c:2667 [inline] __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x307/0x490 net/socket.c:2674 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Uninit was created at: slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768 slab_alloc_node mm/slub.c:3478 [inline] kmem_cache_alloc_node+0x5e9/0xb10 mm/slub.c:3523 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:560 __alloc_skb+0x318/0x740 net/core/skbuff.c:651 alloc_skb include/linux/skbuff.h:1286 [inline] alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6334 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2780 sock_alloc_send_skb include/net/sock.h:1884 [inline] raw_sendmsg+0x36d/0xc10 net/ieee802154/socket.c:282 ieee802154_sock_sendmsg+0x91/0xc0 net/ieee802154/socket.c:96 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] ____sys_sendmsg+0x9c2/0xd60 net/socket.c:2584 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2638 __sys_sendmsg net/socket.c:2667 [inline] __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x307/0x490 net/socket.c:2674 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b CPU: 0 PID: 5037 Comm: syz-executor166 Not tainted 6.7.0-rc7-syzkaller-00003-gfbafc3e621c3 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023 ===================================================== This issue occurs because the skb buffer is too small, and it's actual allocation is aligned. This hides an actual issue, which is that nr_route_frame does not validate the buffer size before using it. Fix this issue by checking skb->len before accessing any fields in skb->data. Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix deadlock during uvc_probe If uvc_probe() fails, it can end up calling uvc_status_unregister() before uvc_status_init() is called. Fix this by checking if dev->status is NULL or not in uvc_status_unregister().

In the Linux kernel, the following vulnerability has been resolved: clk: mmp: pxa1908-mpmu: Fix a NULL vs IS_ERR() check The devm_kzalloc() function returns NULL on error, not error pointers. Update the check to match.

In the Linux kernel, the following vulnerability has been resolved: nvme-pci: fix freeing of the HMB descriptor table The HMB descriptor table is sized to the maximum number of descriptors that could be used for a given device, but __nvme_alloc_host_mem could break out of the loop earlier on memory allocation failure and end up using less descriptors than planned for, which leads to an incorrect size passed to dma_free_coherent. In practice this was not showing up because the number of descriptors tends to be low and the dma coherent allocator always allocates and frees at least a page.

In the Linux kernel, the following vulnerability has been resolved: mailbox: th1520: Fix a NULL vs IS_ERR() bug The devm_ioremap() function doesn't return error pointers, it returns NULL. Update the error checking to match.

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Fix qi_batch NULL pointer with nested parent domain The qi_batch is allocated when assigning cache tag for a domain. While for nested parent domain, it is missed. Hence, when trying to map pages to the nested parent, NULL dereference occurred. Also, there is potential memleak since there is no lock around domain->qi_batch allocation. To solve it, add a helper for qi_batch allocation, and call it in both the __cache_tag_assign_domain() and __cache_tag_assign_parent_domain(). BUG: kernel NULL pointer dereference, address: 0000000000000200 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 8104795067 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 223 UID: 0 PID: 4357 Comm: qemu-system-x86 Not tainted 6.13.0-rc1-00028-g4b50c3c3b998-dirty #2632 Call Trace: ? __die+0x24/0x70 ? page_fault_oops+0x80/0x150 ? do_user_addr_fault+0x63/0x7b0 ? exc_page_fault+0x7c/0x220 ? asm_exc_page_fault+0x26/0x30 ? cache_tag_flush_range_np+0x13c/0x260 intel_iommu_iotlb_sync_map+0x1a/0x30 iommu_map+0x61/0xf0 batch_to_domain+0x188/0x250 iopt_area_fill_domains+0x125/0x320 ? rcu_is_watching+0x11/0x50 iopt_map_pages+0x63/0x100 iopt_map_common.isra.0+0xa7/0x190 iopt_map_user_pages+0x6a/0x80 iommufd_ioas_map+0xcd/0x1d0 iommufd_fops_ioctl+0x118/0x1c0 __x64_sys_ioctl+0x93/0xc0 do_syscall_64+0x71/0x140 entry_SYSCALL_64_after_hwframe+0x76/0x7e

In the Linux kernel, the following vulnerability has been resolved: virtio-blk: don't keep queue frozen during system suspend Commit 4ce6e2db00de ("virtio-blk: Ensure no requests in virtqueues before deleting vqs.") replaces queue quiesce with queue freeze in virtio-blk's PM callbacks. And the motivation is to drain inflight IOs before suspending. block layer's queue freeze looks very handy, but it is also easy to cause deadlock, such as, any attempt to call into bio_queue_enter() may run into deadlock if the queue is frozen in current context. There are all kinds of ->suspend() called in suspend context, so keeping queue frozen in the whole suspend context isn't one good idea. And Marek reported lockdep warning[1] caused by virtio-blk's freeze queue in virtblk_freeze(). [1] https://lore.kernel.org/linux-block/ca16370e-d646-4eee-b9cc-87277c89c43c@samsung.com/ Given the motivation is to drain in-flight IOs, it can be done by calling freeze & unfreeze, meantime restore to previous behavior by keeping queue quiesced during suspend.

In the Linux kernel, the following vulnerability has been resolved: crypto: caam - Fix the pointer passed to caam_qi_shutdown() The type of the last parameter given to devm_add_action_or_reset() is "struct caam_drv_private *", but in caam_qi_shutdown(), it is casted to "struct device *". Pass the correct parameter to devm_add_action_or_reset() so that the resources are released as expected.

In the Linux kernel, the following vulnerability has been resolved: net/smc: protect link down work from execute after lgr freed link down work may be scheduled before lgr freed but execute after lgr freed, which may result in crash. So it is need to hold a reference before shedule link down work, and put the reference after work executed or canceled. The relevant crash call stack as follows: list_del corruption. prev->next should be ffffb638c9c0fe20, but was 0000000000000000 ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:51! invalid opcode: 0000 [#1] SMP NOPTI CPU: 6 PID: 978112 Comm: kworker/6:119 Kdump: loaded Tainted: G #1 Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 2221b89 04/01/2014 Workqueue: events smc_link_down_work [smc] RIP: 0010:__list_del_entry_valid.cold+0x31/0x47 RSP: 0018:ffffb638c9c0fdd8 EFLAGS: 00010086 RAX: 0000000000000054 RBX: ffff942fb75e5128 RCX: 0000000000000000 RDX: ffff943520930aa0 RSI: ffff94352091fc80 RDI: ffff94352091fc80 RBP: 0000000000000000 R08: 0000000000000000 R09: ffffb638c9c0fc38 R10: ffffb638c9c0fc30 R11: ffffffffa015eb28 R12: 0000000000000002 R13: ffffb638c9c0fe20 R14: 0000000000000001 R15: ffff942f9cd051c0 FS: 0000000000000000(0000) GS:ffff943520900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f4f25214000 CR3: 000000025fbae004 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: rwsem_down_write_slowpath+0x17e/0x470 smc_link_down_work+0x3c/0x60 [smc] process_one_work+0x1ac/0x350 worker_thread+0x49/0x2f0 ? rescuer_thread+0x360/0x360 kthread+0x118/0x140 ? __kthread_bind_mask+0x60/0x60 ret_from_fork+0x1f/0x30

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: tests: Fix potential NULL dereference in test_cfg80211_parse_colocated_ap() kunit_kzalloc() may return NULL, dereferencing it without NULL check may lead to NULL dereference. Add a NULL check for ies.

In the Linux kernel, the following vulnerability has been resolved: wifi: rtlwifi: fix memory leaks and invalid access at probe error path Deinitialize at reverse order when probe fails. When init_sw_vars fails, rtl_deinit_core should not be called, specially now that it destroys the rtl_wq workqueue. And call rtl_pci_deinit and deinit_sw_vars, otherwise, memory will be leaked. Remove pci_set_drvdata call as it will already be cleaned up by the core driver code and could lead to memory leaks too. cf. commit 8d450935ae7f ("wireless: rtlwifi: remove unnecessary pci_set_drvdata()") and commit 3d86b93064c7 ("rtlwifi: Fix PCI probe error path orphaned memory").

In the Linux kernel, the following vulnerability has been resolved: iavf: fix hang on reboot with ice When a system with E810 with existing VFs gets rebooted the following hang may be observed. Pid 1 is hung in iavf_remove(), part of a network driver: PID: 1 TASK: ffff965400e5a340 CPU: 24 COMMAND: "systemd-shutdow" #0 [ffffaad04005fa50] __schedule at ffffffff8b3239cb #1 [ffffaad04005fae8] schedule at ffffffff8b323e2d #2 [ffffaad04005fb00] schedule_hrtimeout_range_clock at ffffffff8b32cebc #3 [ffffaad04005fb80] usleep_range_state at ffffffff8b32c930 #4 [ffffaad04005fbb0] iavf_remove at ffffffffc12b9b4c [iavf] #5 [ffffaad04005fbf0] pci_device_remove at ffffffff8add7513 #6 [ffffaad04005fc10] device_release_driver_internal at ffffffff8af08baa #7 [ffffaad04005fc40] pci_stop_bus_device at ffffffff8adcc5fc #8 [ffffaad04005fc60] pci_stop_and_remove_bus_device at ffffffff8adcc81e #9 [ffffaad04005fc70] pci_iov_remove_virtfn at ffffffff8adf9429 #10 [ffffaad04005fca8] sriov_disable at ffffffff8adf98e4 #11 [ffffaad04005fcc8] ice_free_vfs at ffffffffc04bb2c8 [ice] #12 [ffffaad04005fd10] ice_remove at ffffffffc04778fe [ice] #13 [ffffaad04005fd38] ice_shutdown at ffffffffc0477946 [ice] #14 [ffffaad04005fd50] pci_device_shutdown at ffffffff8add58f1 #15 [ffffaad04005fd70] device_shutdown at ffffffff8af05386 #16 [ffffaad04005fd98] kernel_restart at ffffffff8a92a870 #17 [ffffaad04005fda8] __do_sys_reboot at ffffffff8a92abd6 #18 [ffffaad04005fee0] do_syscall_64 at ffffffff8b317159 #19 [ffffaad04005ff08] __context_tracking_enter at ffffffff8b31b6fc #20 [ffffaad04005ff18] syscall_exit_to_user_mode at ffffffff8b31b50d #21 [ffffaad04005ff28] do_syscall_64 at ffffffff8b317169 #22 [ffffaad04005ff50] entry_SYSCALL_64_after_hwframe at ffffffff8b40009b RIP: 00007f1baa5c13d7 RSP: 00007fffbcc55a98 RFLAGS: 00000202 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1baa5c13d7 RDX: 0000000001234567 RSI: 0000000028121969 RDI: 00000000fee1dead RBP: 00007fffbcc55ca0 R8: 0000000000000000 R9: 00007fffbcc54e90 R10: 00007fffbcc55050 R11: 0000000000000202 R12: 0000000000000005 R13: 0000000000000000 R14: 00007fffbcc55af0 R15: 0000000000000000 ORIG_RAX: 00000000000000a9 CS: 0033 SS: 002b During reboot all drivers PM shutdown callbacks are invoked. In iavf_shutdown() the adapter state is changed to __IAVF_REMOVE. In ice_shutdown() the call chain above is executed, which at some point calls iavf_remove(). However iavf_remove() expects the VF to be in one of the states __IAVF_RUNNING, __IAVF_DOWN or __IAVF_INIT_FAILED. If that's not the case it sleeps forever. So if iavf_shutdown() gets invoked before iavf_remove() the system will hang indefinitely because the adapter is already in state __IAVF_REMOVE. Fix this by returning from iavf_remove() if the state is __IAVF_REMOVE, as we already went through iavf_shutdown().