In the Linux kernel, the following vulnerability has been resolved: iio: adc: ti-ads1298: Add NULL check in ads1298_init devm_kasprintf() can return a NULL pointer on failure. A check on the return value of such a call in ads1298_init() is missing. Add it.

In the Linux kernel, the following vulnerability has been resolved: pinctrl: mcp23s08: Fix sleeping in atomic context due to regmap locking If a device uses MCP23xxx IO expander to receive IRQs, the following bug can happen: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:283 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, ... preempt_count: 1, expected: 0 ... Call Trace: ... __might_resched+0x104/0x10e __might_sleep+0x3e/0x62 mutex_lock+0x20/0x4c regmap_lock_mutex+0x10/0x18 regmap_update_bits_base+0x2c/0x66 mcp23s08_irq_set_type+0x1ae/0x1d6 __irq_set_trigger+0x56/0x172 __setup_irq+0x1e6/0x646 request_threaded_irq+0xb6/0x160 ... We observed the problem while experimenting with a touchscreen driver which used MCP23017 IO expander (I2C). The regmap in the pinctrl-mcp23s08 driver uses a mutex for protection from concurrent accesses, which is the default for regmaps without .fast_io, .disable_locking, etc. mcp23s08_irq_set_type() calls regmap_update_bits_base(), and the latter locks the mutex. However, __setup_irq() locks desc->lock spinlock before calling these functions. As a result, the system tries to lock the mutex whole holding the spinlock. It seems, the internal regmap locks are not needed in this driver at all. mcp->lock seems to protect the regmap from concurrent accesses already, except, probably, in mcp_pinconf_get/set. mcp23s08_irq_set_type() and mcp23s08_irq_mask/unmask() are called under chip_bus_lock(), which calls mcp23s08_irq_bus_lock(). The latter takes mcp->lock and enables regmap caching, so that the potentially slow I2C accesses are deferred until chip_bus_unlock(). The accesses to the regmap from mcp23s08_probe_one() do not need additional locking. In all remaining places where the regmap is accessed, except mcp_pinconf_get/set(), the driver already takes mcp->lock. This patch adds locking in mcp_pinconf_get/set() and disables internal locking in the regmap config. Among other things, it fixes the sleeping in atomic context described above.

In the Linux kernel, the following vulnerability has been resolved: memcg: fix soft lockup in the OOM process A soft lockup issue was found in the product with about 56,000 tasks were in the OOM cgroup, it was traversing them when the soft lockup was triggered. watchdog: BUG: soft lockup - CPU#2 stuck for 23s! [VM Thread:1503066] CPU: 2 PID: 1503066 Comm: VM Thread Kdump: loaded Tainted: G Hardware name: Huawei Cloud OpenStack Nova, BIOS RIP: 0010:console_unlock+0x343/0x540 RSP: 0000:ffffb751447db9a0 EFLAGS: 00000247 ORIG_RAX: ffffffffffffff13 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 00000000ffffffff RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000247 RBP: ffffffffafc71f90 R08: 0000000000000000 R09: 0000000000000040 R10: 0000000000000080 R11: 0000000000000000 R12: ffffffffafc74bd0 R13: ffffffffaf60a220 R14: 0000000000000247 R15: 0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2fe6ad91f0 CR3: 00000004b2076003 CR4: 0000000000360ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: vprintk_emit+0x193/0x280 printk+0x52/0x6e dump_task+0x114/0x130 mem_cgroup_scan_tasks+0x76/0x100 dump_header+0x1fe/0x210 oom_kill_process+0xd1/0x100 out_of_memory+0x125/0x570 mem_cgroup_out_of_memory+0xb5/0xd0 try_charge+0x720/0x770 mem_cgroup_try_charge+0x86/0x180 mem_cgroup_try_charge_delay+0x1c/0x40 do_anonymous_page+0xb5/0x390 handle_mm_fault+0xc4/0x1f0 This is because thousands of processes are in the OOM cgroup, it takes a long time to traverse all of them. As a result, this lead to soft lockup in the OOM process. To fix this issue, call 'cond_resched' in the 'mem_cgroup_scan_tasks' function per 1000 iterations. For global OOM, call 'touch_softlockup_watchdog' per 1000 iterations to avoid this issue.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix deadlock when freeing cgroup storage The following commit bc235cdb423a ("bpf: Prevent deadlock from recursive bpf_task_storage_[get|delete]") first introduced deadlock prevention for fentry/fexit programs attaching on bpf_task_storage helpers. That commit also employed the logic in map free path in its v6 version. Later bpf_cgrp_storage was first introduced in c4bcfb38a95e ("bpf: Implement cgroup storage available to non-cgroup-attached bpf progs") which faces the same issue as bpf_task_storage, instead of its busy counter, NULL was passed to bpf_local_storage_map_free() which opened a window to cause deadlock: <TASK> (acquiring local_storage->lock) _raw_spin_lock_irqsave+0x3d/0x50 bpf_local_storage_update+0xd1/0x460 bpf_cgrp_storage_get+0x109/0x130 bpf_prog_a4d4a370ba857314_cgrp_ptr+0x139/0x170 ? __bpf_prog_enter_recur+0x16/0x80 bpf_trampoline_6442485186+0x43/0xa4 cgroup_storage_ptr+0x9/0x20 (holding local_storage->lock) bpf_selem_unlink_storage_nolock.constprop.0+0x135/0x160 bpf_selem_unlink_storage+0x6f/0x110 bpf_local_storage_map_free+0xa2/0x110 bpf_map_free_deferred+0x5b/0x90 process_one_work+0x17c/0x390 worker_thread+0x251/0x360 kthread+0xd2/0x100 ret_from_fork+0x34/0x50 ret_from_fork_asm+0x1a/0x30 </TASK> Progs: - A: SEC("fentry/cgroup_storage_ptr") - cgid (BPF_MAP_TYPE_HASH) Record the id of the cgroup the current task belonging to in this hash map, using the address of the cgroup as the map key. - cgrpa (BPF_MAP_TYPE_CGRP_STORAGE) If current task is a kworker, lookup the above hash map using function parameter @owner as the key to get its corresponding cgroup id which is then used to get a trusted pointer to the cgroup through bpf_cgroup_from_id(). This trusted pointer can then be passed to bpf_cgrp_storage_get() to finally trigger the deadlock issue. - B: SEC("tp_btf/sys_enter") - cgrpb (BPF_MAP_TYPE_CGRP_STORAGE) The only purpose of this prog is to fill Prog A's hash map by calling bpf_cgrp_storage_get() for as many userspace tasks as possible. Steps to reproduce: - Run A; - while (true) { Run B; Destroy B; } Fix this issue by passing its busy counter to the free procedure so it can be properly incremented before storage/smap locking.

In the Linux kernel, the following vulnerability has been resolved: dma-buf/sw-sync: don't enable IRQ from sync_print_obj() Since commit a6aa8fca4d79 ("dma-buf/sw-sync: Reduce irqsave/irqrestore from known context") by error replaced spin_unlock_irqrestore() with spin_unlock_irq() for both sync_debugfs_show() and sync_print_obj() despite sync_print_obj() is called from sync_debugfs_show(), lockdep complains inconsistent lock state warning. Use plain spin_{lock,unlock}() for sync_print_obj(), for sync_debugfs_show() is already using spin_{lock,unlock}_irq().

In the Linux kernel, the following vulnerability has been resolved: drm/i915: Grab intel_display from the encoder to avoid potential oopsies Grab the intel_display from 'encoder' rather than 'state' in the encoder hooks to avoid the massive footgun that is intel_sanitize_encoder(), which passes NULL as the 'state' argument to encoder .disable() and .post_disable(). TODO: figure out how to actually fix intel_sanitize_encoder()...

In the Linux kernel, the following vulnerability has been resolved: bpf: check changes_pkt_data property for extension programs When processing calls to global sub-programs, verifier decides whether to invalidate all packet pointers in current state depending on the changes_pkt_data property of the global sub-program. Because of this, an extension program replacing a global sub-program must be compatible with changes_pkt_data property of the sub-program being replaced. This commit: - adds changes_pkt_data flag to struct bpf_prog_aux: - this flag is set in check_cfg() for main sub-program; - in jit_subprogs() for other sub-programs; - modifies bpf_check_attach_btf_id() to check changes_pkt_data flag; - moves call to check_attach_btf_id() after the call to check_cfg(), because it needs changes_pkt_data flag to be set: bpf_check: ... ... - check_attach_btf_id resolve_pseudo_ldimm64 resolve_pseudo_ldimm64 --> bpf_prog_is_offloaded bpf_prog_is_offloaded check_cfg check_cfg + check_attach_btf_id ... ... The following fields are set by check_attach_btf_id(): - env->ops - prog->aux->attach_btf_trace - prog->aux->attach_func_name - prog->aux->attach_func_proto - prog->aux->dst_trampoline - prog->aux->mod - prog->aux->saved_dst_attach_type - prog->aux->saved_dst_prog_type - prog->expected_attach_type Neither of these fields are used by resolve_pseudo_ldimm64() or bpf_prog_offload_verifier_prep() (for netronome and netdevsim drivers), so the reordering is safe.

In the Linux kernel, the following vulnerability has been resolved: irqchip/gic-v3-its: Don't enable interrupts in its_irq_set_vcpu_affinity() The following call-chain leads to enabling interrupts in a nested interrupt disabled section: irq_set_vcpu_affinity() irq_get_desc_lock() raw_spin_lock_irqsave() <--- Disable interrupts its_irq_set_vcpu_affinity() guard(raw_spinlock_irq) <--- Enables interrupts when leaving the guard() irq_put_desc_unlock() <--- Warns because interrupts are enabled This was broken in commit b97e8a2f7130, which replaced the original raw_spin_[un]lock() pair with guard(raw_spinlock_irq). Fix the issue by using guard(raw_spinlock). [ tglx: Massaged change log ]

In the Linux kernel, the following vulnerability has been resolved: can: j1939: fix errant WARN_ON_ONCE in j1939_session_deactivate The conclusion "j1939_session_deactivate() should be called with a session ref-count of at least 2" is incorrect. In some concurrent scenarios, j1939_session_deactivate can be called with the session ref-count less than 2. But there is not any problem because it will check the session active state before session putting in j1939_session_deactivate_locked(). Here is the concurrent scenario of the problem reported by syzbot and my reproduction log. cpu0 cpu1 j1939_xtp_rx_eoma j1939_xtp_rx_abort_one j1939_session_get_by_addr [kref == 2] j1939_session_get_by_addr [kref == 3] j1939_session_deactivate [kref == 2] j1939_session_put [kref == 1] j1939_session_completed j1939_session_deactivate WARN_ON_ONCE(kref < 2) ===================================================== WARNING: CPU: 1 PID: 21 at net/can/j1939/transport.c:1088 j1939_session_deactivate+0x5f/0x70 CPU: 1 PID: 21 Comm: ksoftirqd/1 Not tainted 5.14.0-rc7+ #32 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014 RIP: 0010:j1939_session_deactivate+0x5f/0x70 Call Trace: j1939_session_deactivate_activate_next+0x11/0x28 j1939_xtp_rx_eoma+0x12a/0x180 j1939_tp_recv+0x4a2/0x510 j1939_can_recv+0x226/0x380 can_rcv_filter+0xf8/0x220 can_receive+0x102/0x220 ? process_backlog+0xf0/0x2c0 can_rcv+0x53/0xf0 __netif_receive_skb_one_core+0x67/0x90 ? process_backlog+0x97/0x2c0 __netif_receive_skb+0x22/0x80

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: pltfrm: Dellocate HBA during ufshcd_pltfrm_remove() This will ensure that the scsi host is cleaned up properly using scsi_host_dev_release(). Otherwise, it may lead to memory leaks.

In the Linux kernel, the following vulnerability has been resolved: bpf: consider that tail calls invalidate packet pointers Tail-called programs could execute any of the helpers that invalidate packet pointers. Hence, conservatively assume that each tail call invalidates packet pointers. Making the change in bpf_helper_changes_pkt_data() automatically makes use of check_cfg() logic that computes 'changes_pkt_data' effect for global sub-programs, such that the following program could be rejected: int tail_call(struct __sk_buff *sk) { bpf_tail_call_static(sk, &jmp_table, 0); return 0; } SEC("tc") int not_safe(struct __sk_buff *sk) { int *p = (void *)(long)sk->data; ... make p valid ... tail_call(sk); *p = 42; /* this is unsafe */ ... } The tc_bpf2bpf.c:subprog_tc() needs change: mark it as a function that can invalidate packet pointers. Otherwise, it can't be freplaced with tailcall_freplace.c:entry_freplace() that does a tail call.

In the Linux kernel, the following vulnerability has been resolved: ptr_ring: do not block hard interrupts in ptr_ring_resize_multiple() Jakub added a lockdep_assert_no_hardirq() check in __page_pool_put_page() to increase test coverage. syzbot found a splat caused by hard irq blocking in ptr_ring_resize_multiple() [1] As current users of ptr_ring_resize_multiple() do not require hard irqs being masked, replace it to only block BH. Rename helpers to better reflect they are safe against BH only. - ptr_ring_resize_multiple() to ptr_ring_resize_multiple_bh() - skb_array_resize_multiple() to skb_array_resize_multiple_bh() [1] WARNING: CPU: 1 PID: 9150 at net/core/page_pool.c:709 __page_pool_put_page net/core/page_pool.c:709 [inline] WARNING: CPU: 1 PID: 9150 at net/core/page_pool.c:709 page_pool_put_unrefed_netmem+0x157/0xa40 net/core/page_pool.c:780 Modules linked in: CPU: 1 UID: 0 PID: 9150 Comm: syz.1.1052 Not tainted 6.11.0-rc3-syzkaller-00202-gf8669d7b5f5d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024 RIP: 0010:__page_pool_put_page net/core/page_pool.c:709 [inline] RIP: 0010:page_pool_put_unrefed_netmem+0x157/0xa40 net/core/page_pool.c:780 Code: 74 0e e8 7c aa fb f7 eb 43 e8 75 aa fb f7 eb 3c 65 8b 1d 38 a8 6a 76 31 ff 89 de e8 a3 ae fb f7 85 db 74 0b e8 5a aa fb f7 90 <0f> 0b 90 eb 1d 65 8b 1d 15 a8 6a 76 31 ff 89 de e8 84 ae fb f7 85 RSP: 0018:ffffc9000bda6b58 EFLAGS: 00010083 RAX: ffffffff8997e523 RBX: 0000000000000000 RCX: 0000000000040000 RDX: ffffc9000fbd0000 RSI: 0000000000001842 RDI: 0000000000001843 RBP: 0000000000000000 R08: ffffffff8997df2c R09: 1ffffd40003a000d R10: dffffc0000000000 R11: fffff940003a000e R12: ffffea0001d00040 R13: ffff88802e8a4000 R14: dffffc0000000000 R15: 00000000ffffffff FS: 00007fb7aaf716c0(0000) GS:ffff8880b9300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fa15a0d4b72 CR3: 00000000561b0000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> tun_ptr_free drivers/net/tun.c:617 [inline] __ptr_ring_swap_queue include/linux/ptr_ring.h:571 [inline] ptr_ring_resize_multiple_noprof include/linux/ptr_ring.h:643 [inline] tun_queue_resize drivers/net/tun.c:3694 [inline] tun_device_event+0xaaf/0x1080 drivers/net/tun.c:3714 notifier_call_chain+0x19f/0x3e0 kernel/notifier.c:93 call_netdevice_notifiers_extack net/core/dev.c:2032 [inline] call_netdevice_notifiers net/core/dev.c:2046 [inline] dev_change_tx_queue_len+0x158/0x2a0 net/core/dev.c:9024 do_setlink+0xff6/0x41f0 net/core/rtnetlink.c:2923 rtnl_setlink+0x40d/0x5a0 net/core/rtnetlink.c:3201 rtnetlink_rcv_msg+0x73f/0xcf0 net/core/rtnetlink.c:6647 netlink_rcv_skb+0x1e3/0x430 net/netlink/af_netlink.c:2550

In the Linux kernel, the following vulnerability has been resolved: printk: Fix signed integer overflow when defining LOG_BUF_LEN_MAX Shifting 1 << 31 on a 32-bit int causes signed integer overflow, which leads to undefined behavior. To prevent this, cast 1 to u32 before performing the shift, ensuring well-defined behavior. This change explicitly avoids any potential overflow by ensuring that the shift occurs on an unsigned 32-bit integer.

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: tests: Fix potential NULL dereference in test_cfg80211_parse_colocated_ap() kunit_kzalloc() may return NULL, dereferencing it without NULL check may lead to NULL dereference. Add a NULL check for ies.

In the Linux kernel, the following vulnerability has been resolved: mm: vmscan: account for free pages to prevent infinite Loop in throttle_direct_reclaim() The task sometimes continues looping in throttle_direct_reclaim() because allow_direct_reclaim(pgdat) keeps returning false. #0 [ffff80002cb6f8d0] __switch_to at ffff8000080095ac #1 [ffff80002cb6f900] __schedule at ffff800008abbd1c #2 [ffff80002cb6f990] schedule at ffff800008abc50c #3 [ffff80002cb6f9b0] throttle_direct_reclaim at ffff800008273550 #4 [ffff80002cb6fa20] try_to_free_pages at ffff800008277b68 #5 [ffff80002cb6fae0] __alloc_pages_nodemask at ffff8000082c4660 #6 [ffff80002cb6fc50] alloc_pages_vma at ffff8000082e4a98 #7 [ffff80002cb6fca0] do_anonymous_page at ffff80000829f5a8 #8 [ffff80002cb6fce0] __handle_mm_fault at ffff8000082a5974 #9 [ffff80002cb6fd90] handle_mm_fault at ffff8000082a5bd4 At this point, the pgdat contains the following two zones: NODE: 4 ZONE: 0 ADDR: ffff00817fffe540 NAME: "DMA32" SIZE: 20480 MIN/LOW/HIGH: 11/28/45 VM_STAT: NR_FREE_PAGES: 359 NR_ZONE_INACTIVE_ANON: 18813 NR_ZONE_ACTIVE_ANON: 0 NR_ZONE_INACTIVE_FILE: 50 NR_ZONE_ACTIVE_FILE: 0 NR_ZONE_UNEVICTABLE: 0 NR_ZONE_WRITE_PENDING: 0 NR_MLOCK: 0 NR_BOUNCE: 0 NR_ZSPAGES: 0 NR_FREE_CMA_PAGES: 0 NODE: 4 ZONE: 1 ADDR: ffff00817fffec00 NAME: "Normal" SIZE: 8454144 PRESENT: 98304 MIN/LOW/HIGH: 68/166/264 VM_STAT: NR_FREE_PAGES: 146 NR_ZONE_INACTIVE_ANON: 94668 NR_ZONE_ACTIVE_ANON: 3 NR_ZONE_INACTIVE_FILE: 735 NR_ZONE_ACTIVE_FILE: 78 NR_ZONE_UNEVICTABLE: 0 NR_ZONE_WRITE_PENDING: 0 NR_MLOCK: 0 NR_BOUNCE: 0 NR_ZSPAGES: 0 NR_FREE_CMA_PAGES: 0 In allow_direct_reclaim(), while processing ZONE_DMA32, the sum of inactive/active file-backed pages calculated in zone_reclaimable_pages() based on the result of zone_page_state_snapshot() is zero. Additionally, since this system lacks swap, the calculation of inactive/ active anonymous pages is skipped. crash> p nr_swap_pages nr_swap_pages = $1937 = { counter = 0 } As a result, ZONE_DMA32 is deemed unreclaimable and skipped, moving on to the processing of the next zone, ZONE_NORMAL, despite ZONE_DMA32 having free pages significantly exceeding the high watermark. The problem is that the pgdat->kswapd_failures hasn't been incremented. crash> px ((struct pglist_data *) 0xffff00817fffe540)->kswapd_failures $1935 = 0x0 This is because the node deemed balanced. The node balancing logic in balance_pgdat() evaluates all zones collectively. If one or more zones (e.g., ZONE_DMA32) have enough free pages to meet their watermarks, the entire node is deemed balanced. This causes balance_pgdat() to exit early before incrementing the kswapd_failures, as it considers the overall memory state acceptable, even though some zones (like ZONE_NORMAL) remain under significant pressure. The patch ensures that zone_reclaimable_pages() includes free pages (NR_FREE_PAGES) in its calculation when no other reclaimable pages are available (e.g., file-backed or anonymous pages). This change prevents zones like ZONE_DMA32, which have sufficient free pages, from being mistakenly deemed unreclaimable. By doing so, the patch ensures proper node balancing, avoids masking pressure on other zones like ZONE_NORMAL, and prevents infinite loops in throttle_direct_reclaim() caused by allow_direct_reclaim(pgdat) repeatedly returning false. The kernel hangs due to a task stuck in throttle_direct_reclaim(), caused by a node being incorrectly deemed balanced despite pressure in certain zones, such as ZONE_NORMAL. This issue arises from zone_reclaimable_pages ---truncated---

In the Linux kernel, the following vulnerability has been resolved: gve: guard XDP xmit NDO on existence of xdp queues In GVE, dedicated XDP queues only exist when an XDP program is installed and the interface is up. As such, the NDO XDP XMIT callback should return early if either of these conditions are false. In the case of no loaded XDP program, priv->num_xdp_queues=0 which can cause a divide-by-zero error, and in the case of interface down, num_xdp_queues remains untouched to persist XDP queue count for the next interface up, but the TX pointer itself would be NULL. The XDP xmit callback also needs to synchronize with a device transitioning from open to close. This synchronization will happen via the GVE_PRIV_FLAGS_NAPI_ENABLED bit along with a synchronize_net() call, which waits for any RCU critical sections at call-time to complete.

In the Linux kernel, the following vulnerability has been resolved: tomoyo: don't emit warning in tomoyo_write_control() syzbot is reporting too large allocation warning at tomoyo_write_control(), for one can write a very very long line without new line character. To fix this warning, I use __GFP_NOWARN rather than checking for KMALLOC_MAX_SIZE, for practically a valid line should be always shorter than 32KB where the "too small to fail" memory-allocation rule applies. One might try to write a valid line that is longer than 32KB, but such request will likely fail with -ENOMEM. Therefore, I feel that separately returning -EINVAL when a line is longer than KMALLOC_MAX_SIZE is redundant. There is no need to distinguish over-32KB and over-KMALLOC_MAX_SIZE.

In the Linux kernel, the following vulnerability has been resolved: team: prevent adding a device which is already a team device lower Prevent adding a device which is already a team device lower, e.g. adding veth0 if vlan1 was already added and veth0 is a lower of vlan1. This is not useful in practice and can lead to recursive locking: $ ip link add veth0 type veth peer name veth1 $ ip link set veth0 up $ ip link set veth1 up $ ip link add link veth0 name veth0.1 type vlan protocol 802.1Q id 1 $ ip link add team0 type team $ ip link set veth0.1 down $ ip link set veth0.1 master team0 team0: Port device veth0.1 added $ ip link set veth0 down $ ip link set veth0 master team0 ============================================ WARNING: possible recursive locking detected 6.13.0-rc2-virtme-00441-ga14a429069bb #46 Not tainted -------------------------------------------- ip/7684 is trying to acquire lock: ffff888016848e00 (team->team_lock_key){+.+.}-{4:4}, at: team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) but task is already holding lock: ffff888016848e00 (team->team_lock_key){+.+.}-{4:4}, at: team_add_slave (drivers/net/team/team_core.c:1147 drivers/net/team/team_core.c:1977) other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(team->team_lock_key); lock(team->team_lock_key); *** DEADLOCK *** May be due to missing lock nesting notation 2 locks held by ip/7684: stack backtrace: CPU: 3 UID: 0 PID: 7684 Comm: ip Not tainted 6.13.0-rc2-virtme-00441-ga14a429069bb #46 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:122) print_deadlock_bug.cold (kernel/locking/lockdep.c:3040) __lock_acquire (kernel/locking/lockdep.c:3893 kernel/locking/lockdep.c:5226) ? netlink_broadcast_filtered (net/netlink/af_netlink.c:1548) lock_acquire.part.0 (kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5851) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) ? trace_lock_acquire (./include/trace/events/lock.h:24 (discriminator 2)) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) ? lock_acquire (kernel/locking/lockdep.c:5822) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) __mutex_lock (kernel/locking/mutex.c:587 kernel/locking/mutex.c:735) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) ? fib_sync_up (net/ipv4/fib_semantics.c:2167) ? team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) team_device_event (drivers/net/team/team_core.c:2928 drivers/net/team/team_core.c:2951 drivers/net/team/team_core.c:2973) notifier_call_chain (kernel/notifier.c:85) call_netdevice_notifiers_info (net/core/dev.c:1996) __dev_notify_flags (net/core/dev.c:8993) ? __dev_change_flags (net/core/dev.c:8975) dev_change_flags (net/core/dev.c:9027) vlan_device_event (net/8021q/vlan.c:85 net/8021q/vlan.c:470) ? br_device_event (net/bridge/br.c:143) notifier_call_chain (kernel/notifier.c:85) call_netdevice_notifiers_info (net/core/dev.c:1996) dev_open (net/core/dev.c:1519 net/core/dev.c:1505) team_add_slave (drivers/net/team/team_core.c:1219 drivers/net/team/team_core.c:1977) ? __pfx_team_add_slave (drivers/net/team/team_core.c:1972) do_set_master (net/core/rtnetlink.c:2917) do_setlink.isra.0 (net/core/rtnetlink.c:3117)

In the Linux kernel, the following vulnerability has been resolved: nfs: Fix oops in nfs_netfs_init_request() when copying to cache When netfslib wants to copy some data that has just been read on behalf of nfs, it creates a new write request and calls nfs_netfs_init_request() to initialise it, but with a NULL file pointer. This causes nfs_file_open_context() to oops - however, we don't actually need the nfs context as we're only going to write to the cache. Fix this by just returning if we aren't given a file pointer and emit a warning if the request was for something other than copy-to-cache. Further, fix nfs_netfs_free_request() so that it doesn't try to free the context if the pointer is NULL.

In the Linux kernel, the following vulnerability has been resolved: rhashtable: Fix potential deadlock by moving schedule_work outside lock Move the hash table growth check and work scheduling outside the rht lock to prevent a possible circular locking dependency. The original implementation could trigger a lockdep warning due to a potential deadlock scenario involving nested locks between rhashtable bucket, rq lock, and dsq lock. By relocating the growth check and work scheduling after releasing the rth lock, we break this potential deadlock chain. This change expands the flexibility of rhashtable by removing restrictive locking that previously limited its use in scheduler and workqueue contexts. Import to say that this calls rht_grow_above_75(), which reads from struct rhashtable without holding the lock, if this is a problem, we can move the check to the lock, and schedule the workqueue after the lock. Modified so that atomic_inc is also moved outside of the bucket lock along with the growth above 75% check.

In the Linux kernel, the following vulnerability has been resolved: dmaengine: at_xdmac: avoid null_prt_deref in at_xdmac_prep_dma_memset The at_xdmac_memset_create_desc may return NULL, which will lead to a null pointer dereference. For example, the len input is error, or the atchan->free_descs_list is empty and memory is exhausted. Therefore, add check to avoid this.

In the Linux kernel, the following vulnerability has been resolved: sched/numa: fix memory leak due to the overwritten vma->numab_state [Problem Description] When running the hackbench program of LTP, the following memory leak is reported by kmemleak. # /opt/ltp/testcases/bin/hackbench 20 thread 1000 Running with 20*40 (== 800) tasks. # dmesg | grep kmemleak ... kmemleak: 480 new suspected memory leaks (see /sys/kernel/debug/kmemleak) kmemleak: 665 new suspected memory leaks (see /sys/kernel/debug/kmemleak) # cat /sys/kernel/debug/kmemleak unreferenced object 0xffff888cd8ca2c40 (size 64): comm "hackbench", pid 17142, jiffies 4299780315 hex dump (first 32 bytes): ac 74 49 00 01 00 00 00 4c 84 49 00 01 00 00 00 .tI.....L.I..... 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace (crc bff18fd4): [<ffffffff81419a89>] __kmalloc_cache_noprof+0x2f9/0x3f0 [<ffffffff8113f715>] task_numa_work+0x725/0xa00 [<ffffffff8110f878>] task_work_run+0x58/0x90 [<ffffffff81ddd9f8>] syscall_exit_to_user_mode+0x1c8/0x1e0 [<ffffffff81dd78d5>] do_syscall_64+0x85/0x150 [<ffffffff81e0012b>] entry_SYSCALL_64_after_hwframe+0x76/0x7e ... This issue can be consistently reproduced on three different servers: * a 448-core server * a 256-core server * a 192-core server [Root Cause] Since multiple threads are created by the hackbench program (along with the command argument 'thread'), a shared vma might be accessed by two or more cores simultaneously. When two or more cores observe that vma->numab_state is NULL at the same time, vma->numab_state will be overwritten. Although current code ensures that only one thread scans the VMAs in a single 'numa_scan_period', there might be a chance for another thread to enter in the next 'numa_scan_period' while we have not gotten till numab_state allocation [1]. Note that the command `/opt/ltp/testcases/bin/hackbench 50 process 1000` cannot the reproduce the issue. It is verified with 200+ test runs. [Solution] Use the cmpxchg atomic operation to ensure that only one thread executes the vma->numab_state assignment. [1] https://lore.kernel.org/lkml/1794be3c-358c-4cdc-a43d-a1f841d91ef7@amd.com/

In the Linux kernel, the following vulnerability has been resolved: geneve: do not assume mac header is set in geneve_xmit_skb() We should not assume mac header is set in output path. Use skb_eth_hdr() instead of eth_hdr() to fix the issue. sysbot reported the following : WARNING: CPU: 0 PID: 11635 at include/linux/skbuff.h:3052 skb_mac_header include/linux/skbuff.h:3052 [inline] WARNING: CPU: 0 PID: 11635 at include/linux/skbuff.h:3052 eth_hdr include/linux/if_ether.h:24 [inline] WARNING: CPU: 0 PID: 11635 at include/linux/skbuff.h:3052 geneve_xmit_skb drivers/net/geneve.c:898 [inline] WARNING: CPU: 0 PID: 11635 at include/linux/skbuff.h:3052 geneve_xmit+0x4c38/0x5730 drivers/net/geneve.c:1039 Modules linked in: CPU: 0 UID: 0 PID: 11635 Comm: syz.4.1423 Not tainted 6.12.0-syzkaller-10296-gaaf20f870da0 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 RIP: 0010:skb_mac_header include/linux/skbuff.h:3052 [inline] RIP: 0010:eth_hdr include/linux/if_ether.h:24 [inline] RIP: 0010:geneve_xmit_skb drivers/net/geneve.c:898 [inline] RIP: 0010:geneve_xmit+0x4c38/0x5730 drivers/net/geneve.c:1039 Code: 21 c6 02 e9 35 d4 ff ff e8 a5 48 4c fb 90 0f 0b 90 e9 fd f5 ff ff e8 97 48 4c fb 90 0f 0b 90 e9 d8 f5 ff ff e8 89 48 4c fb 90 <0f> 0b 90 e9 41 e4 ff ff e8 7b 48 4c fb 90 0f 0b 90 e9 cd e7 ff ff RSP: 0018:ffffc90003b2f870 EFLAGS: 00010283 RAX: 000000000000037a RBX: 000000000000ffff RCX: ffffc9000dc3d000 RDX: 0000000000080000 RSI: ffffffff86428417 RDI: 0000000000000003 RBP: ffffc90003b2f9f0 R08: 0000000000000003 R09: 000000000000ffff R10: 000000000000ffff R11: 0000000000000002 R12: ffff88806603c000 R13: 0000000000000000 R14: ffff8880685b2780 R15: 0000000000000e23 FS: 00007fdc2deed6c0(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000001b30a1dff8 CR3: 0000000056b8c000 CR4: 00000000003526f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __netdev_start_xmit include/linux/netdevice.h:5002 [inline] netdev_start_xmit include/linux/netdevice.h:5011 [inline] __dev_direct_xmit+0x58a/0x720 net/core/dev.c:4490 dev_direct_xmit include/linux/netdevice.h:3181 [inline] packet_xmit+0x1e4/0x360 net/packet/af_packet.c:285 packet_snd net/packet/af_packet.c:3146 [inline] packet_sendmsg+0x2700/0x5660 net/packet/af_packet.c:3178 sock_sendmsg_nosec net/socket.c:711 [inline] __sock_sendmsg net/socket.c:726 [inline] __sys_sendto+0x488/0x4f0 net/socket.c:2197 __do_sys_sendto net/socket.c:2204 [inline] __se_sys_sendto net/socket.c:2200 [inline] __x64_sys_sendto+0xe0/0x1c0 net/socket.c:2200 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: drm/vc4: hdmi: Avoid hang with debug registers when suspended Trying to read /sys/kernel/debug/dri/1/hdmi1_regs when the hdmi is disconnected results in a fatal system hang. This is due to the pm suspend code disabling the dvp clock. That is just a gate of the 108MHz clock in DVP_HT_RPI_MISC_CONFIG, which results in accesses hanging AXI bus. Protect against this.

In the Linux kernel, the following vulnerability has been resolved: vfio/mlx5: Fix an unwind issue in mlx5vf_add_migration_pages() Fix an unwind issue in mlx5vf_add_migration_pages(). If a set of pages is allocated but fails to be added to the SG table, they need to be freed to prevent a memory leak. Any pages successfully added to the SG table will be freed as part of mlx5vf_free_data_buffer().

In the Linux kernel, the following vulnerability has been resolved: erofs: fix blksize < PAGE_SIZE for file-backed mounts Adjust sb->s_blocksize{,_bits} directly for file-backed mounts when the fs block size is smaller than PAGE_SIZE. Previously, EROFS used sb_set_blocksize(), which caused a panic if bdev-backed mounts is not used.

In the Linux kernel, the following vulnerability has been resolved: wifi: ath10k: avoid NULL pointer error during sdio remove When running 'rmmod ath10k', ath10k_sdio_remove() will free sdio workqueue by destroy_workqueue(). But if CONFIG_INIT_ON_FREE_DEFAULT_ON is set to yes, kernel panic will happen: Call trace: destroy_workqueue+0x1c/0x258 ath10k_sdio_remove+0x84/0x94 sdio_bus_remove+0x50/0x16c device_release_driver_internal+0x188/0x25c device_driver_detach+0x20/0x2c This is because during 'rmmod ath10k', ath10k_sdio_remove() will call ath10k_core_destroy() before destroy_workqueue(). wiphy_dev_release() will finally be called in ath10k_core_destroy(). This function will free struct cfg80211_registered_device *rdev and all its members, including wiphy, dev and the pointer of sdio workqueue. Then the pointer of sdio workqueue will be set to NULL due to CONFIG_INIT_ON_FREE_DEFAULT_ON. After device release, destroy_workqueue() will use NULL pointer then the kernel panic happen. Call trace: ath10k_sdio_remove ->ath10k_core_unregister …… ->ath10k_core_stop ->ath10k_hif_stop ->ath10k_sdio_irq_disable ->ath10k_hif_power_down ->del_timer_sync(&ar_sdio->sleep_timer) ->ath10k_core_destroy ->ath10k_mac_destroy ->ieee80211_free_hw ->wiphy_free …… ->wiphy_dev_release ->destroy_workqueue Need to call destroy_workqueue() before ath10k_core_destroy(), free the work queue buffer first and then free pointer of work queue by ath10k_core_destroy(). This order matches the error path order in ath10k_sdio_probe(). No work will be queued on sdio workqueue between it is destroyed and ath10k_core_destroy() is called. Based on the call_stack above, the reason is: Only ath10k_sdio_sleep_timer_handler(), ath10k_sdio_hif_tx_sg() and ath10k_sdio_irq_disable() will queue work on sdio workqueue. Sleep timer will be deleted before ath10k_core_destroy() in ath10k_hif_power_down(). ath10k_sdio_irq_disable() only be called in ath10k_hif_stop(). ath10k_core_unregister() will call ath10k_hif_power_down() to stop hif bus, so ath10k_sdio_hif_tx_sg() won't be called anymore. Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00189

In the Linux kernel, the following vulnerability has been resolved: mfd: intel_soc_pmic_bxtwc: Use IRQ domain for PMIC devices While design wise the idea of converting the driver to use the hierarchy of the IRQ chips is correct, the implementation has (inherited) flaws. This was unveiled when platform_get_irq() had started WARN() on IRQ 0 that is supposed to be a Linux IRQ number (also known as vIRQ). Rework the driver to respect IRQ domain when creating each MFD device separately, as the domain is not the same for all of them.

In the Linux kernel, the following vulnerability has been resolved: net: mscc: ocelot: fix incorrect IFH SRC_PORT field in ocelot_ifh_set_basic() Packets injected by the CPU should have a SRC_PORT field equal to the CPU port module index in the Analyzer block (ocelot->num_phys_ports). The blamed commit copied the ocelot_ifh_set_basic() call incorrectly from ocelot_xmit_common() in net/dsa/tag_ocelot.c. Instead of calling with "x", it calls with BIT_ULL(x), but the field is not a port mask, but rather a single port index. [ side note: this is the technical debt of code duplication :( ] The error used to be silent and doesn't appear to have other user-visible manifestations, but with new changes in the packing library, it now fails loudly as follows: ------------[ cut here ]------------ Cannot store 0x40 inside bits 46-43 - will truncate sja1105 spi2.0: xmit timed out WARNING: CPU: 1 PID: 102 at lib/packing.c:98 __pack+0x90/0x198 sja1105 spi2.0: timed out polling for tstamp CPU: 1 UID: 0 PID: 102 Comm: felix_xmit Tainted: G W N 6.13.0-rc1-00372-gf706b85d972d-dirty #2605 Call trace: __pack+0x90/0x198 (P) __pack+0x90/0x198 (L) packing+0x78/0x98 ocelot_ifh_set_basic+0x260/0x368 ocelot_port_inject_frame+0xa8/0x250 felix_port_deferred_xmit+0x14c/0x258 kthread_worker_fn+0x134/0x350 kthread+0x114/0x138 The code path pertains to the ocelot switchdev driver and to the felix secondary DSA tag protocol, ocelot-8021q. Here seen with ocelot-8021q. The messenger (packing) is not really to blame, so fix the original commit instead.

In the Linux kernel, the following vulnerability has been resolved: io_uring/tctx: work around xa_store() allocation error issue syzbot triggered the following WARN_ON: WARNING: CPU: 0 PID: 16 at io_uring/tctx.c:51 __io_uring_free+0xfa/0x140 io_uring/tctx.c:51 which is the WARN_ON_ONCE(!xa_empty(&tctx->xa)); sanity check in __io_uring_free() when a io_uring_task is going through its final put. The syzbot test case includes injecting memory allocation failures, and it very much looks like xa_store() can fail one of its memory allocations and end up with ->head being non-NULL even though no entries exist in the xarray. Until this issue gets sorted out, work around it by attempting to iterate entries in our xarray, and WARN_ON_ONCE() if one is found.

In the Linux kernel, the following vulnerability has been resolved: nvme-tcp: fix the memleak while create new ctrl failed Now while we create new ctrl failed, we have not free the tagset occupied by admin_q, here try to fix it.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Cancel RTC work during ufshcd_remove() Currently, RTC work is only cancelled during __ufshcd_wl_suspend(). When ufshcd is removed in ufshcd_remove(), RTC work is not cancelled. Due to this, any further trigger of the RTC work after ufshcd_remove() would result in a NULL pointer dereference as below: Unable to handle kernel NULL pointer dereference at virtual address 00000000000002a4 Workqueue: events ufshcd_rtc_work Call trace: _raw_spin_lock_irqsave+0x34/0x8c pm_runtime_get_if_active+0x24/0xb4 ufshcd_rtc_work+0x124/0x19c process_scheduled_works+0x18c/0x2d8 worker_thread+0x144/0x280 kthread+0x11c/0x128 ret_from_fork+0x10/0x20 Since RTC work accesses the ufshcd internal structures, it should be cancelled when ufshcd is removed. So do that in ufshcd_remove(), as per the order in ufshcd_init().

In the Linux kernel, the following vulnerability has been resolved: crypto: bcm - add error check in the ahash_hmac_init function The ahash_init functions may return fails. The ahash_hmac_init should not return ok when ahash_init returns error. For an example, ahash_init will return -ENOMEM when allocation memory is error.

In the Linux kernel, the following vulnerability has been resolved: net: hsr: avoid potential out-of-bound access in fill_frame_info() syzbot is able to feed a packet with 14 bytes, pretending it is a vlan one. Since fill_frame_info() is relying on skb->mac_len already, extend the check to cover this case. BUG: KMSAN: uninit-value in fill_frame_info net/hsr/hsr_forward.c:709 [inline] BUG: KMSAN: uninit-value in hsr_forward_skb+0x9ee/0x3b10 net/hsr/hsr_forward.c:724 fill_frame_info net/hsr/hsr_forward.c:709 [inline] hsr_forward_skb+0x9ee/0x3b10 net/hsr/hsr_forward.c:724 hsr_dev_xmit+0x2f0/0x350 net/hsr/hsr_device.c:235 __netdev_start_xmit include/linux/netdevice.h:5002 [inline] netdev_start_xmit include/linux/netdevice.h:5011 [inline] xmit_one net/core/dev.c:3590 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3606 __dev_queue_xmit+0x366a/0x57d0 net/core/dev.c:4434 dev_queue_xmit include/linux/netdevice.h:3168 [inline] packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3146 [inline] packet_sendmsg+0x91ae/0xa6f0 net/packet/af_packet.c:3178 sock_sendmsg_nosec net/socket.c:711 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:726 __sys_sendto+0x594/0x750 net/socket.c:2197 __do_sys_sendto net/socket.c:2204 [inline] __se_sys_sendto net/socket.c:2200 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2200 x64_sys_call+0x346a/0x3c30 arch/x86/include/generated/asm/syscalls_64.h:45 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:4091 [inline] slab_alloc_node mm/slub.c:4134 [inline] kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4186 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:587 __alloc_skb+0x363/0x7b0 net/core/skbuff.c:678 alloc_skb include/linux/skbuff.h:1323 [inline] alloc_skb_with_frags+0xc8/0xd00 net/core/skbuff.c:6612 sock_alloc_send_pskb+0xa81/0xbf0 net/core/sock.c:2881 packet_alloc_skb net/packet/af_packet.c:2995 [inline] packet_snd net/packet/af_packet.c:3089 [inline] packet_sendmsg+0x74c6/0xa6f0 net/packet/af_packet.c:3178 sock_sendmsg_nosec net/socket.c:711 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:726 __sys_sendto+0x594/0x750 net/socket.c:2197 __do_sys_sendto net/socket.c:2204 [inline] __se_sys_sendto net/socket.c:2200 [inline] __x64_sys_sendto+0x125/0x1d0 net/socket.c:2200 x64_sys_call+0x346a/0x3c30 arch/x86/include/generated/asm/syscalls_64.h:45 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: drm/i915: Fix NULL pointer dereference in capture_engine When the intel_context structure contains NULL, it raises a NULL pointer dereference error in drm_info(). (cherry picked from commit 754302a5bc1bd8fd3b7d85c168b0a1af6d4bba4d)

In the Linux kernel, the following vulnerability has been resolved: octeontx2-pf: handle otx2_mbox_get_rsp errors in otx2_flows.c Adding error pointer check after calling otx2_mbox_get_rsp().

In the Linux kernel, the following vulnerability has been resolved: gpio: graniterapids: Fix vGPIO driver crash Move setting irq_chip.name from probe() function to the initialization of "irq_chip" struct in order to fix vGPIO driver crash during bootup. Crash was caused by unauthorized modification of irq_chip.name field where irq_chip struct was initialized as const. This behavior is a consequence of suboptimal implementation of gpio_irq_chip_set_chip(), which should be changed to avoid casting away const qualifier. Crash log: BUG: unable to handle page fault for address: ffffffffc0ba81c0 /#PF: supervisor write access in kernel mode /#PF: error_code(0x0003) - permissions violation CPU: 33 UID: 0 PID: 1075 Comm: systemd-udevd Not tainted 6.12.0-rc6-00077-g2e1b3cc9d7f7 #1 Hardware name: Intel Corporation Kaseyville RP/Kaseyville RP, BIOS KVLDCRB1.PGS.0026.D73.2410081258 10/08/2024 RIP: 0010:gnr_gpio_probe+0x171/0x220 [gpio_graniterapids]

In the Linux kernel, the following vulnerability has been resolved: i3c: master: Fix miss free init_dyn_addr at i3c_master_put_i3c_addrs() if (dev->boardinfo && dev->boardinfo->init_dyn_addr) ^^^ here check "init_dyn_addr" i3c_bus_set_addr_slot_status(&master->bus, dev->info.dyn_addr, ...) ^^^^ free "dyn_addr" Fix copy/paste error "dyn_addr" by replacing it with "init_dyn_addr".

In the Linux kernel, the following vulnerability has been resolved: drm/modes: Avoid divide by zero harder in drm_mode_vrefresh() drm_mode_vrefresh() is trying to avoid divide by zero by checking whether htotal or vtotal are zero. But we may still end up with a div-by-zero of vtotal*htotal*...

In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: Fix memcpy() field-spanning write warning in mwifiex_config_scan() Replace one-element array with a flexible-array member in `struct mwifiex_ie_types_wildcard_ssid_params` to fix the following warning on a MT8173 Chromebook (mt8173-elm-hana): [ 356.775250] ------------[ cut here ]------------ [ 356.784543] memcpy: detected field-spanning write (size 6) of single field "wildcard_ssid_tlv->ssid" at drivers/net/wireless/marvell/mwifiex/scan.c:904 (size 1) [ 356.813403] WARNING: CPU: 3 PID: 742 at drivers/net/wireless/marvell/mwifiex/scan.c:904 mwifiex_scan_networks+0x4fc/0xf28 [mwifiex] The "(size 6)" above is exactly the length of the SSID of the network this device was connected to. The source of the warning looks like: ssid_len = user_scan_in->ssid_list[i].ssid_len; [...] memcpy(wildcard_ssid_tlv->ssid, user_scan_in->ssid_list[i].ssid, ssid_len); There is a #define WILDCARD_SSID_TLV_MAX_SIZE that uses sizeof() on this struct, but it already didn't account for the size of the one-element array, so it doesn't need to be changed.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: free inode when ocfs2_get_init_inode() fails syzbot is reporting busy inodes after unmount, for commit 9c89fe0af826 ("ocfs2: Handle error from dquot_initialize()") forgot to call iput() when new_inode() succeeded and dquot_initialize() failed.

In the Linux kernel, the following vulnerability has been resolved: bpf,perf: Fix invalid prog_array access in perf_event_detach_bpf_prog Syzbot reported [1] crash that happens for following tracing scenario: - create tracepoint perf event with attr.inherit=1, attach it to the process and set bpf program to it - attached process forks -> chid creates inherited event the new child event shares the parent's bpf program and tp_event (hence prog_array) which is global for tracepoint - exit both process and its child -> release both events - first perf_event_detach_bpf_prog call will release tp_event->prog_array and second perf_event_detach_bpf_prog will crash, because tp_event->prog_array is NULL The fix makes sure the perf_event_detach_bpf_prog checks prog_array is valid before it tries to remove the bpf program from it. [1] https://lore.kernel.org/bpf/Z1MR6dCIKajNS6nU@krava/T/#m91dbf0688221ec7a7fc95e896a7ef9ff93b0b8ad

In the Linux kernel, the following vulnerability has been resolved: rtc: check if __rtc_read_time was successful in rtc_timer_do_work() If the __rtc_read_time call fails,, the struct rtc_time tm; may contain uninitialized data, or an illegal date/time read from the RTC hardware. When calling rtc_tm_to_ktime later, the result may be a very large value (possibly KTIME_MAX). If there are periodic timers in rtc->timerqueue, they will continually expire, may causing kernel softlockup.

In the Linux kernel, the following vulnerability has been resolved: bpf: fix recursive lock when verdict program return SK_PASS When the stream_verdict program returns SK_PASS, it places the received skb into its own receive queue, but a recursive lock eventually occurs, leading to an operating system deadlock. This issue has been present since v6.9. ''' sk_psock_strp_data_ready write_lock_bh(&sk->sk_callback_lock) strp_data_ready strp_read_sock read_sock -> tcp_read_sock strp_recv cb.rcv_msg -> sk_psock_strp_read # now stream_verdict return SK_PASS without peer sock assign __SK_PASS = sk_psock_map_verd(SK_PASS, NULL) sk_psock_verdict_apply sk_psock_skb_ingress_self sk_psock_skb_ingress_enqueue sk_psock_data_ready read_lock_bh(&sk->sk_callback_lock) <= dead lock ''' This topic has been discussed before, but it has not been fixed. Previous discussion: https://lore.kernel.org/all/6684a5864ec86_403d20898@john.notmuch

In the Linux kernel, the following vulnerability has been resolved: net/sched: netem: account for backlog updates from child qdisc In general, 'qlen' of any classful qdisc should keep track of the number of packets that the qdisc itself and all of its children holds. In case of netem, 'qlen' only accounts for the packets in its internal tfifo. When netem is used with a child qdisc, the child qdisc can use 'qdisc_tree_reduce_backlog' to inform its parent, netem, about created or dropped SKBs. This function updates 'qlen' and the backlog statistics of netem, but netem does not account for changes made by a child qdisc. 'qlen' then indicates the wrong number of packets in the tfifo. If a child qdisc creates new SKBs during enqueue and informs its parent about this, netem's 'qlen' value is increased. When netem dequeues the newly created SKBs from the child, the 'qlen' in netem is not updated. If 'qlen' reaches the configured sch->limit, the enqueue function stops working, even though the tfifo is not full. Reproduce the bug: Ensure that the sender machine has GSO enabled. Configure netem as root qdisc and tbf as its child on the outgoing interface of the machine as follows: $ tc qdisc add dev <oif> root handle 1: netem delay 100ms limit 100 $ tc qdisc add dev <oif> parent 1:0 tbf rate 50Mbit burst 1542 latency 50ms Send bulk TCP traffic out via this interface, e.g., by running an iPerf3 client on the machine. Check the qdisc statistics: $ tc -s qdisc show dev <oif> Statistics after 10s of iPerf3 TCP test before the fix (note that netem's backlog > limit, netem stopped accepting packets): qdisc netem 1: root refcnt 2 limit 1000 delay 100ms Sent 2767766 bytes 1848 pkt (dropped 652, overlimits 0 requeues 0) backlog 4294528236b 1155p requeues 0 qdisc tbf 10: parent 1:1 rate 50Mbit burst 1537b lat 50ms Sent 2767766 bytes 1848 pkt (dropped 327, overlimits 7601 requeues 0) backlog 0b 0p requeues 0 Statistics after the fix: qdisc netem 1: root refcnt 2 limit 1000 delay 100ms Sent 37766372 bytes 24974 pkt (dropped 9, overlimits 0 requeues 0) backlog 0b 0p requeues 0 qdisc tbf 10: parent 1:1 rate 50Mbit burst 1537b lat 50ms Sent 37766372 bytes 24974 pkt (dropped 327, overlimits 96017 requeues 0) backlog 0b 0p requeues 0 tbf segments the GSO SKBs (tbf_segment) and updates the netem's 'qlen'. The interface fully stops transferring packets and "locks". In this case, the child qdisc and tfifo are empty, but 'qlen' indicates the tfifo is at its limit and no more packets are accepted. This patch adds a counter for the entries in the tfifo. Netem's 'qlen' is only decreased when a packet is returned by its dequeue function, and not during enqueuing into the child qdisc. External updates to 'qlen' are thus accounted for and only the behavior of the backlog statistics changes. As in other qdiscs, 'qlen' then keeps track of how many packets are held in netem and all of its children. As before, sch->limit remains as the maximum number of packets in the tfifo. The same applies to netem's backlog statistics.

In the Linux kernel, the following vulnerability has been resolved: usb: musb: Fix hardware lockup on first Rx endpoint request There is a possibility that a request's callback could be invoked from usb_ep_queue() (call trace below, supplemented with missing calls): req->complete from usb_gadget_giveback_request (drivers/usb/gadget/udc/core.c:999) usb_gadget_giveback_request from musb_g_giveback (drivers/usb/musb/musb_gadget.c:147) musb_g_giveback from rxstate (drivers/usb/musb/musb_gadget.c:784) rxstate from musb_ep_restart (drivers/usb/musb/musb_gadget.c:1169) musb_ep_restart from musb_ep_restart_resume_work (drivers/usb/musb/musb_gadget.c:1176) musb_ep_restart_resume_work from musb_queue_resume_work (drivers/usb/musb/musb_core.c:2279) musb_queue_resume_work from musb_gadget_queue (drivers/usb/musb/musb_gadget.c:1241) musb_gadget_queue from usb_ep_queue (drivers/usb/gadget/udc/core.c:300) According to the docstring of usb_ep_queue(), this should not happen: "Note that @req's ->complete() callback must never be called from within usb_ep_queue() as that can create deadlock situations." In fact, a hardware lockup might occur in the following sequence: 1. The gadget is initialized using musb_gadget_enable(). 2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an interrupt. 3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an empty queue (next_request() returns NULL). The interrupt flag has already been cleared by the glue layer handler, but the RXPKTRDY flag remains set. 4. The first request is enqueued using usb_ep_queue(), leading to the call of req->complete(), as shown in the call trace above. 5. If the callback enables IRQs and another packet is waiting, step (3) repeats. The request queue is empty because usb_g_giveback() removes the request before invoking the callback. 6. The endpoint remains locked up, as the interrupt triggered by hardware setting the RXPKTRDY flag has been handled, but the flag itself remains set. For this scenario to occur, it is only necessary for IRQs to be enabled at some point during the complete callback. This happens with the USB Ethernet gadget, whose rx_complete() callback calls netif_rx(). If called in the task context, netif_rx() disables the bottom halves (BHs). When the BHs are re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The gadget itself is initialized at module load (or at boot if built-in), but the first request is enqueued when the network interface is brought up, triggering rx_complete() in the task context via ioctl(). If a packet arrives while the interface is down, it can prevent the interface from receiving any further packets from the USB host. The situation is quite complicated with many parties involved. This particular issue can be resolved in several possible ways: 1. Ensure that callbacks never enable IRQs. This would be difficult to enforce, as discovering how netif_rx() interacts with interrupts was already quite challenging and u_ether is not the only function driver. Similar "bugs" could be hidden in other drivers as well. 2. Disable MUSB interrupts in musb_g_giveback() before calling the callback and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(), for example). This would ensure that MUSB interrupts are not handled during the callback, even if IRQs are enabled. In fact, it would allow IRQs to be enabled when releasing the lock. However, this feels like an inelegant hack. 3. Modify the interrupt handler to clear the RXPKTRDY flag if the request queue is empty. While this approach also feels like a hack, it wastes CPU time by attempting to handle incoming packets when the software is not ready to process them. 4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart(). This ensures that the hardware can receive packets when there is at least one request in the queue. Once I ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net/ipv6: release expired exception dst cached in socket Dst objects get leaked in ip6_negative_advice() when this function is executed for an expired IPv6 route located in the exception table. There are several conditions that must be fulfilled for the leak to occur: * an ICMPv6 packet indicating a change of the MTU for the path is received, resulting in an exception dst being created * a TCP connection that uses the exception dst for routing packets must start timing out so that TCP begins retransmissions * after the exception dst expires, the FIB6 garbage collector must not run before TCP executes ip6_negative_advice() for the expired exception dst When TCP executes ip6_negative_advice() for an exception dst that has expired and if no other socket holds a reference to the exception dst, the refcount of the exception dst is 2, which corresponds to the increment made by dst_init() and the increment made by the TCP socket for which the connection is timing out. The refcount made by the socket is never released. The refcount of the dst is decremented in sk_dst_reset() but that decrement is counteracted by a dst_hold() intentionally placed just before the sk_dst_reset() in ip6_negative_advice(). After ip6_negative_advice() has finished, there is no other object tied to the dst. The socket lost its reference stored in sk_dst_cache and the dst is no longer in the exception table. The exception dst becomes a leaked object. As a result of this dst leak, an unbalanced refcount is reported for the loopback device of a net namespace being destroyed under kernels that do not contain e5f80fcf869a ("ipv6: give an IPv6 dev to blackhole_netdev"): unregister_netdevice: waiting for lo to become free. Usage count = 2 Fix the dst leak by removing the dst_hold() in ip6_negative_advice(). The patch that introduced the dst_hold() in ip6_negative_advice() was 92f1655aa2b22 ("net: fix __dst_negative_advice() race"). But 92f1655aa2b22 merely refactored the code with regards to the dst refcount so the issue was present even before 92f1655aa2b22. The bug was introduced in 54c1a859efd9f ("ipv6: Don't drop cache route entry unless timer actually expired.") where the expired cached route is deleted and the sk_dst_cache member of the socket is set to NULL by calling dst_negative_advice() but the refcount belonging to the socket is left unbalanced. The IPv4 version - ipv4_negative_advice() - is not affected by this bug. When the TCP connection times out ipv4_negative_advice() merely resets the sk_dst_cache of the socket while decrementing the refcount of the exception dst.

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to do sanity check on node blkaddr in truncate_node() syzbot reports a f2fs bug as below: ------------[ cut here ]------------ kernel BUG at fs/f2fs/segment.c:2534! RIP: 0010:f2fs_invalidate_blocks+0x35f/0x370 fs/f2fs/segment.c:2534 Call Trace: truncate_node+0x1ae/0x8c0 fs/f2fs/node.c:909 f2fs_remove_inode_page+0x5c2/0x870 fs/f2fs/node.c:1288 f2fs_evict_inode+0x879/0x15c0 fs/f2fs/inode.c:856 evict+0x4e8/0x9b0 fs/inode.c:723 f2fs_handle_failed_inode+0x271/0x2e0 fs/f2fs/inode.c:986 f2fs_create+0x357/0x530 fs/f2fs/namei.c:394 lookup_open fs/namei.c:3595 [inline] open_last_lookups fs/namei.c:3694 [inline] path_openat+0x1c03/0x3590 fs/namei.c:3930 do_filp_open+0x235/0x490 fs/namei.c:3960 do_sys_openat2+0x13e/0x1d0 fs/open.c:1415 do_sys_open fs/open.c:1430 [inline] __do_sys_openat fs/open.c:1446 [inline] __se_sys_openat fs/open.c:1441 [inline] __x64_sys_openat+0x247/0x2a0 fs/open.c:1441 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0010:f2fs_invalidate_blocks+0x35f/0x370 fs/f2fs/segment.c:2534 The root cause is: on a fuzzed image, blkaddr in nat entry may be corrupted, then it will cause system panic when using it in f2fs_invalidate_blocks(), to avoid this, let's add sanity check on nat blkaddr in truncate_node().

In the Linux kernel, the following vulnerability has been resolved: net: Fix icmp host relookup triggering ip_rt_bug arp link failure may trigger ip_rt_bug while xfrm enabled, call trace is: WARNING: CPU: 0 PID: 0 at net/ipv4/route.c:1241 ip_rt_bug+0x14/0x20 Modules linked in: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.0-rc6-00077-g2e1b3cc9d7f7 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:ip_rt_bug+0x14/0x20 Call Trace: <IRQ> ip_send_skb+0x14/0x40 __icmp_send+0x42d/0x6a0 ipv4_link_failure+0xe2/0x1d0 arp_error_report+0x3c/0x50 neigh_invalidate+0x8d/0x100 neigh_timer_handler+0x2e1/0x330 call_timer_fn+0x21/0x120 __run_timer_base.part.0+0x1c9/0x270 run_timer_softirq+0x4c/0x80 handle_softirqs+0xac/0x280 irq_exit_rcu+0x62/0x80 sysvec_apic_timer_interrupt+0x77/0x90 The script below reproduces this scenario: ip xfrm policy add src 0.0.0.0/0 dst 0.0.0.0/0 \ dir out priority 0 ptype main flag localok icmp ip l a veth1 type veth ip a a 192.168.141.111/24 dev veth0 ip l s veth0 up ping 192.168.141.155 -c 1 icmp_route_lookup() create input routes for locally generated packets while xfrm relookup ICMP traffic.Then it will set input route (dst->out = ip_rt_bug) to skb for DESTUNREACH. For ICMP err triggered by locally generated packets, dst->dev of output route is loopback. Generally, xfrm relookup verification is not required on loopback interfaces (net.ipv4.conf.lo.disable_xfrm = 1). Skip icmp relookup for locally generated packets to fix it.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usx2y: Use snd_card_free_when_closed() at disconnection The USB disconnect callback is supposed to be short and not too-long waiting. OTOH, the current code uses snd_card_free() at disconnection, but this waits for the close of all used fds, hence it can take long. It eventually blocks the upper layer USB ioctls, which may trigger a soft lockup. An easy workaround is to replace snd_card_free() with snd_card_free_when_closed(). This variant returns immediately while the release of resources is done asynchronously by the card device release at the last close.