In the Linux kernel, the following vulnerability has been resolved: hv_netvsc: Don't free decrypted memory In CoCo VMs it is possible for the untrusted host to cause set_memory_encrypted() or set_memory_decrypted() to fail such that an error is returned and the resulting memory is shared. Callers need to take care to handle these errors to avoid returning decrypted (shared) memory to the page allocator, which could lead to functional or security issues. The netvsc driver could free decrypted/shared pages if set_memory_decrypted() fails. Check the decrypted field in the gpadl to decide whether to free the memory.

In the Linux kernel, the following vulnerability has been resolved: team: Move team device type change at the end of team_port_add Attempting to add a port device that is already up will expectedly fail, but not before modifying the team device header_ops. In the case of the syzbot reproducer the gre0 device is already in state UP when it attempts to add it as a port device of team0, this fails but before that header_ops->create of team0 is changed from eth_header to ipgre_header in the call to team_dev_type_check_change. Later when we end up in ipgre_header() struct ip_tunnel* points to nonsense as the private data of the device still holds a struct team. Example sequence of iproute2 commands to reproduce the hang/BUG(): ip link add dev team0 type team ip link add dev gre0 type gre ip link set dev gre0 up ip link set dev gre0 master team0 ip link set dev team0 up ping -I team0 1.1.1.1 Move team_dev_type_check_change down where all other checks have passed as it changes the dev type with no way to restore it in case one of the checks that follow it fail. Also make sure to preserve the origial mtu assignment: - If port_dev is not the same type as dev, dev takes mtu from port_dev - If port_dev is the same type as dev, port_dev takes mtu from dev This is done by adding a conditional before the call to dev_set_mtu to prevent it from assigning port_dev->mtu = dev->mtu and instead letting team_dev_type_check_change assign dev->mtu = port_dev->mtu. The conditional is needed because the patch moves the call to team_dev_type_check_change past dev_set_mtu. Testing: - team device driver in-tree selftests - Add/remove various devices as slaves of team device - syzbot

In the Linux kernel, the following vulnerability has been resolved: Drivers: hv: vmbus: Don't free ring buffers that couldn't be re-encrypted In CoCo VMs it is possible for the untrusted host to cause set_memory_encrypted() or set_memory_decrypted() to fail such that an error is returned and the resulting memory is shared. Callers need to take care to handle these errors to avoid returning decrypted (shared) memory to the page allocator, which could lead to functional or security issues. The VMBus ring buffer code could free decrypted/shared pages if set_memory_decrypted() fails. Check the decrypted field in the struct vmbus_gpadl for the ring buffers to decide whether to free the memory.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs: Ensure 'ib_sge list' is accessible Move the declaration of the 'ib_sge list' variable outside the 'always_invalidate' block to ensure it remains accessible for use throughout the function. Previously, 'ib_sge list' was declared within the 'always_invalidate' block, limiting its accessibility, then caused a 'BUG: kernel NULL pointer dereference'[1]. ? __die_body.cold+0x19/0x27 ? page_fault_oops+0x15a/0x2d0 ? search_module_extables+0x19/0x60 ? search_bpf_extables+0x5f/0x80 ? exc_page_fault+0x7e/0x180 ? asm_exc_page_fault+0x26/0x30 ? memcpy_orig+0xd5/0x140 rxe_mr_copy+0x1c3/0x200 [rdma_rxe] ? rxe_pool_get_index+0x4b/0x80 [rdma_rxe] copy_data+0xa5/0x230 [rdma_rxe] rxe_requester+0xd9b/0xf70 [rdma_rxe] ? finish_task_switch.isra.0+0x99/0x2e0 rxe_sender+0x13/0x40 [rdma_rxe] do_task+0x68/0x1e0 [rdma_rxe] process_one_work+0x177/0x330 worker_thread+0x252/0x390 ? __pfx_worker_thread+0x10/0x10 This change ensures the variable is available for subsequent operations that require it. [1] https://lore.kernel.org/linux-rdma/6a1f3e8f-deb0-49f9-bc69-a9b03ecfcda7@fujitsu.com/

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix a possible null pointer dereference In function lpfc_xcvr_data_show, the memory allocation with kmalloc might fail, thereby making rdp_context a null pointer. In the following context and functions that use this pointer, there are dereferencing operations, leading to null pointer dereference. To fix this issue, a null pointer check should be added. If it is null, use scnprintf to notify the user and return len.

In the Linux kernel, the following vulnerability has been resolved: media: v4l: async: Fix NULL pointer dereference in adding ancillary links In v4l2_async_create_ancillary_links(), ancillary links are created for lens and flash sub-devices. These are sub-device to sub-device links and if the async notifier is related to a V4L2 device, the source sub-device of the ancillary link is NULL, leading to a NULL pointer dereference. Check the notifier's sd field is non-NULL in v4l2_async_create_ancillary_links(). [Sakari Ailus: Reword the subject and commit messages slightly.]

In the Linux kernel, the following vulnerability has been resolved: fpga: bridge: add owner module and take its refcount The current implementation of the fpga bridge assumes that the low-level module registers a driver for the parent device and uses its owner pointer to take the module's refcount. This approach is problematic since it can lead to a null pointer dereference while attempting to get the bridge if the parent device does not have a driver. To address this problem, add a module owner pointer to the fpga_bridge struct and use it to take the module's refcount. Modify the function for registering a bridge to take an additional owner module parameter and rename it to avoid conflicts. Use the old function name for a helper macro that automatically sets the module that registers the bridge as the owner. This ensures compatibility with existing low-level control modules and reduces the chances of registering a bridge without setting the owner. Also, update the documentation to keep it consistent with the new interface for registering an fpga bridge. Other changes: opportunistically move put_device() from __fpga_bridge_get() to fpga_bridge_get() and of_fpga_bridge_get() to improve code clarity since the bridge device is taken in these functions.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: range check cp bad op exception interrupts Due to a CP interrupt bug, bad packet garbage exception codes are raised. Do a range check so that the debugger and runtime do not receive garbage codes. Update the user api to guard exception code type checking as well.

In the Linux kernel, the following vulnerability has been resolved: net/sched: taprio: extend minimum interval restriction to entire cycle too It is possible for syzbot to side-step the restriction imposed by the blamed commit in the Fixes: tag, because the taprio UAPI permits a cycle-time different from (and potentially shorter than) the sum of entry intervals. We need one more restriction, which is that the cycle time itself must be larger than N * ETH_ZLEN bit times, where N is the number of schedule entries. This restriction needs to apply regardless of whether the cycle time came from the user or was the implicit, auto-calculated value, so we move the existing "cycle == 0" check outside the "if "(!new->cycle_time)" branch. This way covers both conditions and scenarios. Add a selftest which illustrates the issue triggered by syzbot.

In the Linux kernel, the following vulnerability has been resolved: kcm: annotate data-races around kcm->rx_psock kcm->rx_psock can be read locklessly in kcm_rfree(). Annotate the read and writes accordingly. We do the same for kcm->rx_wait in the following patch. syzbot reported: BUG: KCSAN: data-race in kcm_rfree / unreserve_rx_kcm write to 0xffff888123d827b8 of 8 bytes by task 2758 on cpu 1: unreserve_rx_kcm+0x72/0x1f0 net/kcm/kcmsock.c:313 kcm_rcv_strparser+0x2b5/0x3a0 net/kcm/kcmsock.c:373 __strp_recv+0x64c/0xd20 net/strparser/strparser.c:301 strp_recv+0x6d/0x80 net/strparser/strparser.c:335 tcp_read_sock+0x13e/0x5a0 net/ipv4/tcp.c:1703 strp_read_sock net/strparser/strparser.c:358 [inline] do_strp_work net/strparser/strparser.c:406 [inline] strp_work+0xe8/0x180 net/strparser/strparser.c:415 process_one_work+0x3d3/0x720 kernel/workqueue.c:2289 worker_thread+0x618/0xa70 kernel/workqueue.c:2436 kthread+0x1a9/0x1e0 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306 read to 0xffff888123d827b8 of 8 bytes by task 5859 on cpu 0: kcm_rfree+0x14c/0x220 net/kcm/kcmsock.c:181 skb_release_head_state+0x8e/0x160 net/core/skbuff.c:841 skb_release_all net/core/skbuff.c:852 [inline] __kfree_skb net/core/skbuff.c:868 [inline] kfree_skb_reason+0x5c/0x260 net/core/skbuff.c:891 kfree_skb include/linux/skbuff.h:1216 [inline] kcm_recvmsg+0x226/0x2b0 net/kcm/kcmsock.c:1161 ____sys_recvmsg+0x16c/0x2e0 ___sys_recvmsg net/socket.c:2743 [inline] do_recvmmsg+0x2f1/0x710 net/socket.c:2837 __sys_recvmmsg net/socket.c:2916 [inline] __do_sys_recvmmsg net/socket.c:2939 [inline] __se_sys_recvmmsg net/socket.c:2932 [inline] __x64_sys_recvmmsg+0xde/0x160 net/socket.c:2932 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd value changed: 0xffff88812971ce00 -> 0x0000000000000000 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 5859 Comm: syz-executor.3 Not tainted 6.0.0-syzkaller-12189-g19d17ab7c68b-dirty #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022

In the Linux kernel, the following vulnerability has been resolved: octeontx2-af: avoid off-by-one read from userspace We try to access count + 1 byte from userspace with memdup_user(buffer, count + 1). However, the userspace only provides buffer of count bytes and only these count bytes are verified to be okay to access. To ensure the copied buffer is NUL terminated, we use memdup_user_nul instead.

In the Linux kernel, the following vulnerability has been resolved: tls: fix missing memory barrier in tls_init In tls_init(), a write memory barrier is missing, and store-store reordering may cause NULL dereference in tls_{setsockopt,getsockopt}. CPU0 CPU1 ----- ----- // In tls_init() // In tls_ctx_create() ctx = kzalloc() ctx->sk_proto = READ_ONCE(sk->sk_prot) -(1) // In update_sk_prot() WRITE_ONCE(sk->sk_prot, tls_prots) -(2) // In sock_common_setsockopt() READ_ONCE(sk->sk_prot)->setsockopt() // In tls_{setsockopt,getsockopt}() ctx->sk_proto->setsockopt() -(3) In the above scenario, when (1) and (2) are reordered, (3) can observe the NULL value of ctx->sk_proto, causing NULL dereference. To fix it, we rely on rcu_assign_pointer() which implies the release barrier semantic. By moving rcu_assign_pointer() after ctx->sk_proto is initialized, we can ensure that ctx->sk_proto are visible when changing sk->sk_prot.

In the Linux kernel, the following vulnerability has been resolved: bpf: Check bloom filter map value size This patch adds a missing check to bloom filter creating, rejecting values above KMALLOC_MAX_SIZE. This brings the bloom map in line with many other map types. The lack of this protection can cause kernel crashes for value sizes that overflow int's. Such a crash was caught by syzkaller. The next patch adds more guard-rails at a lower level.

In the Linux kernel, the following vulnerability has been resolved: thermal/debugfs: Free all thermal zone debug memory on zone removal Because thermal_debug_tz_remove() does not free all memory allocated for thermal zone diagnostics, some of that memory becomes unreachable after freeing the thermal zone's struct thermal_debugfs object. Address this by making thermal_debug_tz_remove() free all of the memory in question. Cc :6.8+ <stable@vger.kernel.org> # 6.8+

In the Linux kernel, the following vulnerability has been resolved: drm/xe: Only use reserved BCS instances for usm migrate exec queue The GuC context scheduling queue is 2 entires deep, thus it is possible for a migration job to be stuck behind a fault if migration exec queue shares engines with user jobs. This can deadlock as the migrate exec queue is required to service page faults. Avoid deadlock by only using reserved BCS instances for usm migrate exec queue. (cherry picked from commit 04f4a70a183a688a60fe3882d6e4236ea02cfc67)

In the Linux kernel, the following vulnerability has been resolved: pinctrl: devicetree: fix refcount leak in pinctrl_dt_to_map() If we fail to allocate propname buffer, we need to drop the reference count we just took. Because the pinctrl_dt_free_maps() includes the droping operation, here we call it directly.

In the Linux kernel, the following vulnerability has been resolved: UM: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK When CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS is selected, cpu_max_bits_warn() generates a runtime warning similar as below while we show /proc/cpuinfo. Fix this by using nr_cpu_ids (the runtime limit) instead of NR_CPUS to iterate CPUs. [ 3.052463] ------------[ cut here ]------------ [ 3.059679] WARNING: CPU: 3 PID: 1 at include/linux/cpumask.h:108 show_cpuinfo+0x5e8/0x5f0 [ 3.070072] Modules linked in: efivarfs autofs4 [ 3.076257] CPU: 0 PID: 1 Comm: systemd Not tainted 5.19-rc5+ #1052 [ 3.099465] Stack : 9000000100157b08 9000000000f18530 9000000000cf846c 9000000100154000 [ 3.109127] 9000000100157a50 0000000000000000 9000000100157a58 9000000000ef7430 [ 3.118774] 90000001001578e8 0000000000000040 0000000000000020 ffffffffffffffff [ 3.128412] 0000000000aaaaaa 1ab25f00eec96a37 900000010021de80 900000000101c890 [ 3.138056] 0000000000000000 0000000000000000 0000000000000000 0000000000aaaaaa [ 3.147711] ffff8000339dc220 0000000000000001 0000000006ab4000 0000000000000000 [ 3.157364] 900000000101c998 0000000000000004 9000000000ef7430 0000000000000000 [ 3.167012] 0000000000000009 000000000000006c 0000000000000000 0000000000000000 [ 3.176641] 9000000000d3de08 9000000001639390 90000000002086d8 00007ffff0080286 [ 3.186260] 00000000000000b0 0000000000000004 0000000000000000 0000000000071c1c [ 3.195868] ... [ 3.199917] Call Trace: [ 3.203941] [<90000000002086d8>] show_stack+0x38/0x14c [ 3.210666] [<9000000000cf846c>] dump_stack_lvl+0x60/0x88 [ 3.217625] [<900000000023d268>] __warn+0xd0/0x100 [ 3.223958] [<9000000000cf3c90>] warn_slowpath_fmt+0x7c/0xcc [ 3.231150] [<9000000000210220>] show_cpuinfo+0x5e8/0x5f0 [ 3.238080] [<90000000004f578c>] seq_read_iter+0x354/0x4b4 [ 3.245098] [<90000000004c2e90>] new_sync_read+0x17c/0x1c4 [ 3.252114] [<90000000004c5174>] vfs_read+0x138/0x1d0 [ 3.258694] [<90000000004c55f8>] ksys_read+0x70/0x100 [ 3.265265] [<9000000000cfde9c>] do_syscall+0x7c/0x94 [ 3.271820] [<9000000000202fe4>] handle_syscall+0xc4/0x160 [ 3.281824] ---[ end trace 8b484262b4b8c24c ]---

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Add null checker before passing variables Checks null pointer before passing variables to functions. This fixes 3 NULL_RETURNS issues reported by Coverity.

In the Linux kernel, the following vulnerability has been resolved: maple_tree: fix mas_empty_area_rev() null pointer dereference Currently the code calls mas_start() followed by mas_data_end() if the maple state is MA_START, but mas_start() may return with the maple state node == NULL. This will lead to a null pointer dereference when checking information in the NULL node, which is done in mas_data_end(). Avoid setting the offset if there is no node by waiting until after the maple state is checked for an empty or single entry state. A user could trigger the events to cause a kernel oops by unmapping all vmas to produce an empty maple tree, then mapping a vma that would cause the scenario described above.

In the Linux kernel, the following vulnerability has been resolved: thermal/debugfs: Prevent use-after-free from occurring after cdev removal Since thermal_debug_cdev_remove() does not run under cdev->lock, it can run in parallel with thermal_debug_cdev_state_update() and it may free the struct thermal_debugfs object used by the latter after it has been checked against NULL. If that happens, thermal_debug_cdev_state_update() will access memory that has been freed already causing the kernel to crash. Address this by using cdev->lock in thermal_debug_cdev_remove() around the cdev->debugfs value check (in case the same cdev is removed at the same time in two different threads) and its reset to NULL. Cc :6.8+ <stable@vger.kernel.org> # 6.8+

In the Linux kernel, the following vulnerability has been resolved: net: ks8851: Queue RX packets in IRQ handler instead of disabling BHs Currently the driver uses local_bh_disable()/local_bh_enable() in its IRQ handler to avoid triggering net_rx_action() softirq on exit from netif_rx(). The net_rx_action() could trigger this driver .start_xmit callback, which is protected by the same lock as the IRQ handler, so calling the .start_xmit from netif_rx() from the IRQ handler critical section protected by the lock could lead to an attempt to claim the already claimed lock, and a hang. The local_bh_disable()/local_bh_enable() approach works only in case the IRQ handler is protected by a spinlock, but does not work if the IRQ handler is protected by mutex, i.e. this works for KS8851 with Parallel bus interface, but not for KS8851 with SPI bus interface. Remove the BH manipulation and instead of calling netif_rx() inside the IRQ handler code protected by the lock, queue all the received SKBs in the IRQ handler into a queue first, and once the IRQ handler exits the critical section protected by the lock, dequeue all the queued SKBs and push them all into netif_rx(). At this point, it is safe to trigger the net_rx_action() softirq, since the netif_rx() call is outside of the lock that protects the IRQ handler.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: Avoid infinite loop trying to resize local TT If the MTU of one of an attached interface becomes too small to transmit the local translation table then it must be resized to fit inside all fragments (when enabled) or a single packet. But if the MTU becomes too low to transmit even the header + the VLAN specific part then the resizing of the local TT will never succeed. This can for example happen when the usable space is 110 bytes and 11 VLANs are on top of batman-adv. In this case, at least 116 byte would be needed. There will just be an endless spam of batman_adv: batadv0: Forced to purge local tt entries to fit new maximum fragment MTU (110) in the log but the function will never finish. Problem here is that the timeout will be halved all the time and will then stagnate at 0 and therefore never be able to reduce the table even more. There are other scenarios possible with a similar result. The number of BATADV_TT_CLIENT_NOPURGE entries in the local TT can for example be too high to fit inside a packet. Such a scenario can therefore happen also with only a single VLAN + 7 non-purgable addresses - requiring at least 120 bytes. While this should be handled proactively when: * interface with too low MTU is added * VLAN is added * non-purgeable local mac is added * MTU of an attached interface is reduced * fragmentation setting gets disabled (which most likely requires dropping attached interfaces) not all of these scenarios can be prevented because batman-adv is only consuming events without the the possibility to prevent these actions (non-purgable MAC address added, MTU of an attached interface is reduced). It is therefore necessary to also make sure that the code is able to handle also the situations when there were already incompatible system configuration are present.

In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: uefisecapp: Fix memory related IO errors and crashes It turns out that while the QSEECOM APP_SEND command has specific fields for request and response buffers, uefisecapp expects them both to be in a single memory region. Failure to adhere to this has (so far) resulted in either no response being written to the response buffer (causing an EIO to be emitted down the line), the SCM call to fail with EINVAL (i.e., directly from TZ/firmware), or the device to be hard-reset. While this issue can be triggered deterministically, in the current form it seems to happen rather sporadically (which is why it has gone unnoticed during earlier testing). This is likely due to the two kzalloc() calls (for request and response) being directly after each other. Which means that those likely return consecutive regions most of the time, especially when not much else is going on in the system. Fix this by allocating a single memory region for both request and response buffers, properly aligning both structs inside it. This unfortunately also means that the qcom_scm_qseecom_app_send() interface needs to be restructured, as it should no longer map the DMA regions separately. Therefore, move the responsibility of DMA allocation (or mapping) to the caller.

In the Linux kernel, the following vulnerability has been resolved: io_uring/kbuf: hold io_buffer_list reference over mmap If we look up the kbuf, ensure that it doesn't get unregistered until after we're done with it. Since we're inside mmap, we cannot safely use the io_uring lock. Rely on the fact that we can lookup the buffer list under RCU now and grab a reference to it, preventing it from being unregistered until we're done with it. The lookup returns the io_buffer_list directly with it referenced.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Fix mlx5e_priv_init() cleanup flow When mlx5e_priv_init() fails, the cleanup flow calls mlx5e_selq_cleanup which calls mlx5e_selq_apply() that assures that the `priv->state_lock` is held using lockdep_is_held(). Acquire the state_lock in mlx5e_selq_cleanup(). Kernel log: ============================= WARNING: suspicious RCU usage 6.8.0-rc3_net_next_841a9b5 #1 Not tainted ----------------------------- drivers/net/ethernet/mellanox/mlx5/core/en/selq.c:124 suspicious rcu_dereference_protected() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 2 locks held by systemd-modules/293: #0: ffffffffa05067b0 (devices_rwsem){++++}-{3:3}, at: ib_register_client+0x109/0x1b0 [ib_core] #1: ffff8881096c65c0 (&device->client_data_rwsem){++++}-{3:3}, at: add_client_context+0x104/0x1c0 [ib_core] stack backtrace: CPU: 4 PID: 293 Comm: systemd-modules Not tainted 6.8.0-rc3_net_next_841a9b5 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x8a/0xa0 lockdep_rcu_suspicious+0x154/0x1a0 mlx5e_selq_apply+0x94/0xa0 [mlx5_core] mlx5e_selq_cleanup+0x3a/0x60 [mlx5_core] mlx5e_priv_init+0x2be/0x2f0 [mlx5_core] mlx5_rdma_setup_rn+0x7c/0x1a0 [mlx5_core] rdma_init_netdev+0x4e/0x80 [ib_core] ? mlx5_rdma_netdev_free+0x70/0x70 [mlx5_core] ipoib_intf_init+0x64/0x550 [ib_ipoib] ipoib_intf_alloc+0x4e/0xc0 [ib_ipoib] ipoib_add_one+0xb0/0x360 [ib_ipoib] add_client_context+0x112/0x1c0 [ib_core] ib_register_client+0x166/0x1b0 [ib_core] ? 0xffffffffa0573000 ipoib_init_module+0xeb/0x1a0 [ib_ipoib] do_one_initcall+0x61/0x250 do_init_module+0x8a/0x270 init_module_from_file+0x8b/0xd0 idempotent_init_module+0x17d/0x230 __x64_sys_finit_module+0x61/0xb0 do_syscall_64+0x71/0x140 entry_SYSCALL_64_after_hwframe+0x46/0x4e </TASK>

In the Linux kernel, the following vulnerability has been resolved: spi: mchp-pci1xxx: Fix a possible null pointer dereference in pci1xxx_spi_probe In function pci1xxxx_spi_probe, there is a potential null pointer that may be caused by a failed memory allocation by the function devm_kzalloc. Hence, a null pointer check needs to be added to prevent null pointer dereferencing later in the code. To fix this issue, spi_bus->spi_int[iter] should be checked. The memory allocated by devm_kzalloc will be automatically released, so just directly return -ENOMEM without worrying about memory leaks.

In the Linux kernel, the following vulnerability has been resolved: aio: Fix null ptr deref in aio_complete() wakeup list_del_init_careful() needs to be the last access to the wait queue entry - it effectively unlocks access. Previously, finish_wait() would see the empty list head and skip taking the lock, and then we'd return - but the completion path would still attempt to do the wakeup after the task_struct pointer had been overwritten.

In the Linux kernel, the following vulnerability has been resolved: xdp: fix invalid wait context of page_pool_destroy() If the driver uses a page pool, it creates a page pool with page_pool_create(). The reference count of page pool is 1 as default. A page pool will be destroyed only when a reference count reaches 0. page_pool_destroy() is used to destroy page pool, it decreases a reference count. When a page pool is destroyed, ->disconnect() is called, which is mem_allocator_disconnect(). This function internally acquires mutex_lock(). If the driver uses XDP, it registers a memory model with xdp_rxq_info_reg_mem_model(). The xdp_rxq_info_reg_mem_model() internally increases a page pool reference count if a memory model is a page pool. Now the reference count is 2. To destroy a page pool, the driver should call both page_pool_destroy() and xdp_unreg_mem_model(). The xdp_unreg_mem_model() internally calls page_pool_destroy(). Only page_pool_destroy() decreases a reference count. If a driver calls page_pool_destroy() then xdp_unreg_mem_model(), we will face an invalid wait context warning. Because xdp_unreg_mem_model() calls page_pool_destroy() with rcu_read_lock(). The page_pool_destroy() internally acquires mutex_lock(). Splat looks like: ============================= [ BUG: Invalid wait context ] 6.10.0-rc6+ #4 Tainted: G W ----------------------------- ethtool/1806 is trying to lock: ffffffff90387b90 (mem_id_lock){+.+.}-{4:4}, at: mem_allocator_disconnect+0x73/0x150 other info that might help us debug this: context-{5:5} 3 locks held by ethtool/1806: stack backtrace: CPU: 0 PID: 1806 Comm: ethtool Tainted: G W 6.10.0-rc6+ #4 f916f41f172891c800f2fed Hardware name: ASUS System Product Name/PRIME Z690-P D4, BIOS 0603 11/01/2021 Call Trace: <TASK> dump_stack_lvl+0x7e/0xc0 __lock_acquire+0x1681/0x4de0 ? _printk+0x64/0xe0 ? __pfx_mark_lock.part.0+0x10/0x10 ? __pfx___lock_acquire+0x10/0x10 lock_acquire+0x1b3/0x580 ? mem_allocator_disconnect+0x73/0x150 ? __wake_up_klogd.part.0+0x16/0xc0 ? __pfx_lock_acquire+0x10/0x10 ? dump_stack_lvl+0x91/0xc0 __mutex_lock+0x15c/0x1690 ? mem_allocator_disconnect+0x73/0x150 ? __pfx_prb_read_valid+0x10/0x10 ? mem_allocator_disconnect+0x73/0x150 ? __pfx_llist_add_batch+0x10/0x10 ? console_unlock+0x193/0x1b0 ? lockdep_hardirqs_on+0xbe/0x140 ? __pfx___mutex_lock+0x10/0x10 ? tick_nohz_tick_stopped+0x16/0x90 ? __irq_work_queue_local+0x1e5/0x330 ? irq_work_queue+0x39/0x50 ? __wake_up_klogd.part.0+0x79/0xc0 ? mem_allocator_disconnect+0x73/0x150 mem_allocator_disconnect+0x73/0x150 ? __pfx_mem_allocator_disconnect+0x10/0x10 ? mark_held_locks+0xa5/0xf0 ? rcu_is_watching+0x11/0xb0 page_pool_release+0x36e/0x6d0 page_pool_destroy+0xd7/0x440 xdp_unreg_mem_model+0x1a7/0x2a0 ? __pfx_xdp_unreg_mem_model+0x10/0x10 ? kfree+0x125/0x370 ? bnxt_free_ring.isra.0+0x2eb/0x500 ? bnxt_free_mem+0x5ac/0x2500 xdp_rxq_info_unreg+0x4a/0xd0 bnxt_free_mem+0x1356/0x2500 bnxt_close_nic+0xf0/0x3b0 ? __pfx_bnxt_close_nic+0x10/0x10 ? ethnl_parse_bit+0x2c6/0x6d0 ? __pfx___nla_validate_parse+0x10/0x10 ? __pfx_ethnl_parse_bit+0x10/0x10 bnxt_set_features+0x2a8/0x3e0 __netdev_update_features+0x4dc/0x1370 ? ethnl_parse_bitset+0x4ff/0x750 ? __pfx_ethnl_parse_bitset+0x10/0x10 ? __pfx___netdev_update_features+0x10/0x10 ? mark_held_locks+0xa5/0xf0 ? _raw_spin_unlock_irqrestore+0x42/0x70 ? __pm_runtime_resume+0x7d/0x110 ethnl_set_features+0x32d/0xa20 To fix this problem, it uses rhashtable_lookup_fast() instead of rhashtable_lookup() with rcu_read_lock(). Using xa without rcu_read_lock() here is safe. xa is freed by __xdp_mem_allocator_rcu_free() and this is called by call_rcu() of mem_xa_remove(). The mem_xa_remove() is called by page_pool_destroy() if a reference count reaches 0. The xa is already protected by the reference count mechanism well in the control plane. So removing rcu_read_lock() for page_pool_destroy() is safe.

In the Linux kernel, the following vulnerability has been resolved: PCI: rcar: Demote WARN() to dev_warn_ratelimited() in rcar_pcie_wakeup() Avoid large backtrace, it is sufficient to warn the user that there has been a link problem. Either the link has failed and the system is in need of maintenance, or the link continues to work and user has been informed. The message from the warning can be looked up in the sources. This makes an actual link issue less verbose. First of all, this controller has a limitation in that the controller driver has to assist the hardware with transition to L1 link state by writing L1IATN to PMCTRL register, the L1 and L0 link state switching is not fully automatic on this controller. In case of an ASMedia ASM1062 PCIe SATA controller which does not support ASPM, on entry to suspend or during platform pm_test, the SATA controller enters D3hot state and the link enters L1 state. If the SATA controller wakes up before rcar_pcie_wakeup() was called and returns to D0, the link returns to L0 before the controller driver even started its transition to L1 link state. At this point, the SATA controller did send an PM_ENTER_L1 DLLP to the PCIe controller and the PCIe controller received it, and the PCIe controller did set PMSR PMEL1RX bit. Once rcar_pcie_wakeup() is called, if the link is already back in L0 state and PMEL1RX bit is set, the controller driver has no way to determine if it should perform the link transition to L1 state, or treat the link as if it is in L0 state. Currently the driver attempts to perform the transition to L1 link state unconditionally, which in this specific case fails with a PMSR L1FAEG poll timeout, however the link still works as it is already back in L0 state. Reduce this warning verbosity. In case the link is really broken, the rcar_pcie_config_access() would fail, otherwise it will succeed and any system with this controller and ASM1062 can suspend without generating a backtrace.

In the Linux kernel, the following vulnerability has been resolved: mm/secretmem: fix GUP-fast succeeding on secretmem folios folio_is_secretmem() currently relies on secretmem folios being LRU folios, to save some cycles. However, folios might reside in a folio batch without the LRU flag set, or temporarily have their LRU flag cleared. Consequently, the LRU flag is unreliable for this purpose. In particular, this is the case when secretmem_fault() allocates a fresh page and calls filemap_add_folio()->folio_add_lru(). The folio might be added to the per-cpu folio batch and won't get the LRU flag set until the batch was drained using e.g., lru_add_drain(). Consequently, folio_is_secretmem() might not detect secretmem folios and GUP-fast can succeed in grabbing a secretmem folio, crashing the kernel when we would later try reading/writing to the folio, because the folio has been unmapped from the directmap. Fix it by removing that unreliable check.

In the Linux kernel, the following vulnerability has been resolved: riscv: Fix vector state restore in rt_sigreturn() The RISC-V Vector specification states in "Appendix D: Calling Convention for Vector State" [1] that "Executing a system call causes all caller-saved vector registers (v0-v31, vl, vtype) and vstart to become unspecified.". In the RISC-V kernel this is called "discarding the vstate". Returning from a signal handler via the rt_sigreturn() syscall, vector discard is also performed. However, this is not an issue since the vector state should be restored from the sigcontext, and therefore not care about the vector discard. The "live state" is the actual vector register in the running context, and the "vstate" is the vector state of the task. A dirty live state, means that the vstate and live state are not in synch. When vectorized user_from_copy() was introduced, an bug sneaked in at the restoration code, related to the discard of the live state. An example when this go wrong: 1. A userland application is executing vector code 2. The application receives a signal, and the signal handler is entered. 3. The application returns from the signal handler, using the rt_sigreturn() syscall. 4. The live vector state is discarded upon entering the rt_sigreturn(), and the live state is marked as "dirty", indicating that the live state need to be synchronized with the current vstate. 5. rt_sigreturn() restores the vstate, except the Vector registers, from the sigcontext 6. rt_sigreturn() restores the Vector registers, from the sigcontext, and now the vectorized user_from_copy() is used. The dirty live state from the discard is saved to the vstate, making the vstate corrupt. 7. rt_sigreturn() returns to the application, which crashes due to corrupted vstate. Note that the vectorized user_from_copy() is invoked depending on the value of CONFIG_RISCV_ISA_V_UCOPY_THRESHOLD. Default is 768, which means that vlen has to be larger than 128b for this bug to trigger. The fix is simply to mark the live state as non-dirty/clean prior performing the vstate restore.

In the Linux kernel, the following vulnerability has been resolved: mlxbf_gige: stop interface during shutdown The mlxbf_gige driver intermittantly encounters a NULL pointer exception while the system is shutting down via "reboot" command. The mlxbf_driver will experience an exception right after executing its shutdown() method. One example of this exception is: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070 Mem abort info: ESR = 0x0000000096000004 EC = 0x25: DABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x04: level 0 translation fault Data abort info: ISV = 0, ISS = 0x00000004 CM = 0, WnR = 0 user pgtable: 4k pages, 48-bit VAs, pgdp=000000011d373000 [0000000000000070] pgd=0000000000000000, p4d=0000000000000000 Internal error: Oops: 96000004 [#1] SMP CPU: 0 PID: 13 Comm: ksoftirqd/0 Tainted: G S OE 5.15.0-bf.6.gef6992a #1 Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS 4.0.2.12669 Apr 21 2023 pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : mlxbf_gige_handle_tx_complete+0xc8/0x170 [mlxbf_gige] lr : mlxbf_gige_poll+0x54/0x160 [mlxbf_gige] sp : ffff8000080d3c10 x29: ffff8000080d3c10 x28: ffffcce72cbb7000 x27: ffff8000080d3d58 x26: ffff0000814e7340 x25: ffff331cd1a05000 x24: ffffcce72c4ea008 x23: ffff0000814e4b40 x22: ffff0000814e4d10 x21: ffff0000814e4128 x20: 0000000000000000 x19: ffff0000814e4a80 x18: ffffffffffffffff x17: 000000000000001c x16: ffffcce72b4553f4 x15: ffff80008805b8a7 x14: 0000000000000000 x13: 0000000000000030 x12: 0101010101010101 x11: 7f7f7f7f7f7f7f7f x10: c2ac898b17576267 x9 : ffffcce720fa5404 x8 : ffff000080812138 x7 : 0000000000002e9a x6 : 0000000000000080 x5 : ffff00008de3b000 x4 : 0000000000000000 x3 : 0000000000000001 x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 Call trace: mlxbf_gige_handle_tx_complete+0xc8/0x170 [mlxbf_gige] mlxbf_gige_poll+0x54/0x160 [mlxbf_gige] __napi_poll+0x40/0x1c8 net_rx_action+0x314/0x3a0 __do_softirq+0x128/0x334 run_ksoftirqd+0x54/0x6c smpboot_thread_fn+0x14c/0x190 kthread+0x10c/0x110 ret_from_fork+0x10/0x20 Code: 8b070000 f9000ea0 f95056c0 f86178a1 (b9407002) ---[ end trace 7cc3941aa0d8e6a4 ]--- Kernel panic - not syncing: Oops: Fatal exception in interrupt Kernel Offset: 0x4ce722520000 from 0xffff800008000000 PHYS_OFFSET: 0x80000000 CPU features: 0x000005c1,a3330e5a Memory Limit: none ---[ end Kernel panic - not syncing: Oops: Fatal exception in interrupt ]--- During system shutdown, the mlxbf_gige driver's shutdown() is always executed. However, the driver's stop() method will only execute if networking interface configuration logic within the Linux distribution has been setup to do so. If shutdown() executes but stop() does not execute, NAPI remains enabled and this can lead to an exception if NAPI is scheduled while the hardware interface has only been partially deinitialized. The networking interface managed by the mlxbf_gige driver must be properly stopped during system shutdown so that IFF_UP is cleared, the hardware interface is put into a clean state, and NAPI is fully deinitialized.

In the Linux kernel, the following vulnerability has been resolved: block: fix module reference leakage from bdev_open_by_dev error path At the time bdev_may_open() is called, module reference is grabbed already, hence module reference should be released if bdev_may_open() failed. This problem is found by code review.

In the Linux kernel, the following vulnerability has been resolved: btrfs: handle chunk tree lookup error in btrfs_relocate_sys_chunks() The unhandled case in btrfs_relocate_sys_chunks() loop is a corruption, as it could be caused only by two impossible conditions: - at first the search key is set up to look for a chunk tree item, with offset -1, this is an inexact search and the key->offset will contain the correct offset upon a successful search, a valid chunk tree item cannot have an offset -1 - after first successful search, the found_key corresponds to a chunk item, the offset is decremented by 1 before the next loop, it's impossible to find a chunk item there due to alignment and size constraints

In the Linux kernel, the following vulnerability has been resolved: dm-raid: Fix WARN_ON_ONCE check for sync_thread in raid_resume rm-raid devices will occasionally trigger the following warning when being resumed after a table load because DM_RECOVERY_RUNNING is set: WARNING: CPU: 7 PID: 5660 at drivers/md/dm-raid.c:4105 raid_resume+0xee/0x100 [dm_raid] The failing check is: WARN_ON_ONCE(test_bit(MD_RECOVERY_RUNNING, &mddev->recovery)); This check is designed to make sure that the sync thread isn't registered, but md_check_recovery can set MD_RECOVERY_RUNNING without the sync_thread ever getting registered. Instead of checking if MD_RECOVERY_RUNNING is set, check if sync_thread is non-NULL.

In the Linux kernel, the following vulnerability has been resolved: bnxt_en: Fix aggregation ID mask to prevent oops on 5760X chips The 5760X (P7) chip's HW GRO/LRO interface is very similar to that of the previous generation (5750X or P5). However, the aggregation ID fields in the completion structures on P7 have been redefined from 16 bits to 12 bits. The freed up 4 bits are redefined for part of the metadata such as the VLAN ID. The aggregation ID mask was not modified when adding support for P7 chips. Including the extra 4 bits for the aggregation ID can potentially cause the driver to store or fetch the packet header of GRO/LRO packets in the wrong TPA buffer. It may hit the BUG() condition in __skb_pull() because the SKB contains no valid packet header: kernel BUG at include/linux/skbuff.h:2766! Oops: invalid opcode: 0000 1 PREEMPT SMP NOPTI CPU: 4 UID: 0 PID: 0 Comm: swapper/4 Kdump: loaded Tainted: G OE 6.12.0-rc2+ #7 Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE Hardware name: Dell Inc. PowerEdge R760/0VRV9X, BIOS 1.0.1 12/27/2022 RIP: 0010:eth_type_trans+0xda/0x140 Code: 80 00 00 00 eb c1 8b 47 70 2b 47 74 48 8b 97 d0 00 00 00 83 f8 01 7e 1b 48 85 d2 74 06 66 83 3a ff 74 09 b8 00 04 00 00 eb a5 <0f> 0b b8 00 01 00 00 eb 9c 48 85 ff 74 eb 31 f6 b9 02 00 00 00 48 RSP: 0018:ff615003803fcc28 EFLAGS: 00010283 RAX: 00000000000022d2 RBX: 0000000000000003 RCX: ff2e8c25da334040 RDX: 0000000000000040 RSI: ff2e8c25c1ce8000 RDI: ff2e8c25869f9000 RBP: ff2e8c258c31c000 R08: ff2e8c25da334000 R09: 0000000000000001 R10: ff2e8c25da3342c0 R11: ff2e8c25c1ce89c0 R12: ff2e8c258e0990b0 R13: ff2e8c25bb120000 R14: ff2e8c25c1ce89c0 R15: ff2e8c25869f9000 FS: 0000000000000000(0000) GS:ff2e8c34be300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055f05317e4c8 CR3: 000000108bac6006 CR4: 0000000000773ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <IRQ> ? die+0x33/0x90 ? do_trap+0xd9/0x100 ? eth_type_trans+0xda/0x140 ? do_error_trap+0x65/0x80 ? eth_type_trans+0xda/0x140 ? exc_invalid_op+0x4e/0x70 ? eth_type_trans+0xda/0x140 ? asm_exc_invalid_op+0x16/0x20 ? eth_type_trans+0xda/0x140 bnxt_tpa_end+0x10b/0x6b0 [bnxt_en] ? bnxt_tpa_start+0x195/0x320 [bnxt_en] bnxt_rx_pkt+0x902/0xd90 [bnxt_en] ? __bnxt_tx_int.constprop.0+0x89/0x300 [bnxt_en] ? kmem_cache_free+0x343/0x440 ? __bnxt_tx_int.constprop.0+0x24f/0x300 [bnxt_en] __bnxt_poll_work+0x193/0x370 [bnxt_en] bnxt_poll_p5+0x9a/0x300 [bnxt_en] ? try_to_wake_up+0x209/0x670 __napi_poll+0x29/0x1b0 Fix it by redefining the aggregation ID mask for P5_PLUS chips to be 12 bits. This will work because the maximum aggregation ID is less than 4096 on all P5_PLUS chips.

In the Linux kernel, the following vulnerability has been resolved: pstore/zone: Add a null pointer check to the psz_kmsg_read kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Ensure the allocation was successful by checking the pointer validity.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: altmodes/displayport: create sysfs nodes as driver's default device attribute group The DisplayPort driver's sysfs nodes may be present to the userspace before typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns NULL in those cases. Remove manual sysfs node creation in favor of adding attribute group as default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is not used here otherwise the path to the sysfs nodes is no longer compliant with the ABI.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btintel: Fix null ptr deref in btintel_read_version If hci_cmd_sync_complete() is triggered and skb is NULL, then hdev->req_skb is NULL, which will cause this issue.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: fix NULL dereference at band check in starting tx ba session In MLD connection, link_data/link_conf are dynamically allocated. They don't point to vif->bss_conf. So, there will be no chanreq assigned to vif->bss_conf and then the chan will be NULL. Tweak the code to check ht_supported/vht_supported/has_he/has_eht on sta deflink. Crash log (with rtw89 version under MLO development): [ 9890.526087] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 9890.526102] #PF: supervisor read access in kernel mode [ 9890.526105] #PF: error_code(0x0000) - not-present page [ 9890.526109] PGD 0 P4D 0 [ 9890.526114] Oops: 0000 [#1] PREEMPT SMP PTI [ 9890.526119] CPU: 2 PID: 6367 Comm: kworker/u16:2 Kdump: loaded Tainted: G OE 6.9.0 #1 [ 9890.526123] Hardware name: LENOVO 2356AD1/2356AD1, BIOS G7ETB3WW (2.73 ) 11/28/2018 [ 9890.526126] Workqueue: phy2 rtw89_core_ba_work [rtw89_core] [ 9890.526203] RIP: 0010:ieee80211_start_tx_ba_session (net/mac80211/agg-tx.c:618 (discriminator 1)) mac80211 [ 9890.526279] Code: f7 e8 d5 93 3e ea 48 83 c4 28 89 d8 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc 49 8b 84 24 e0 f1 ff ff 48 8b 80 90 1b 00 00 <83> 38 03 0f 84 37 fe ff ff bb ea ff ff ff eb cc 49 8b 84 24 10 f3 All code ======== 0: f7 e8 imul %eax 2: d5 (bad) 3: 93 xchg %eax,%ebx 4: 3e ea ds (bad) 6: 48 83 c4 28 add $0x28,%rsp a: 89 d8 mov %ebx,%eax c: 5b pop %rbx d: 41 5c pop %r12 f: 41 5d pop %r13 11: 41 5e pop %r14 13: 41 5f pop %r15 15: 5d pop %rbp 16: c3 retq 17: cc int3 18: cc int3 19: cc int3 1a: cc int3 1b: 49 8b 84 24 e0 f1 ff mov -0xe20(%r12),%rax 22: ff 23: 48 8b 80 90 1b 00 00 mov 0x1b90(%rax),%rax 2a:* 83 38 03 cmpl $0x3,(%rax) <-- trapping instruction 2d: 0f 84 37 fe ff ff je 0xfffffffffffffe6a 33: bb ea ff ff ff mov $0xffffffea,%ebx 38: eb cc jmp 0x6 3a: 49 rex.WB 3b: 8b .byte 0x8b 3c: 84 24 10 test %ah,(%rax,%rdx,1) 3f: f3 repz Code starting with the faulting instruction =========================================== 0: 83 38 03 cmpl $0x3,(%rax) 3: 0f 84 37 fe ff ff je 0xfffffffffffffe40 9: bb ea ff ff ff mov $0xffffffea,%ebx e: eb cc jmp 0xffffffffffffffdc 10: 49 rex.WB 11: 8b .byte 0x8b 12: 84 24 10 test %ah,(%rax,%rdx,1) 15: f3 repz [ 9890.526285] RSP: 0018:ffffb8db09013d68 EFLAGS: 00010246 [ 9890.526291] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff9308e0d656c8 [ 9890.526295] RDX: 0000000000000000 RSI: ffffffffab99460b RDI: ffffffffab9a7685 [ 9890.526300] RBP: ffffb8db09013db8 R08: 0000000000000000 R09: 0000000000000873 [ 9890.526304] R10: ffff9308e0d64800 R11: 0000000000000002 R12: ffff9308e5ff6e70 [ 9890.526308] R13: ffff930952500e20 R14: ffff9309192a8c00 R15: 0000000000000000 [ 9890.526313] FS: 0000000000000000(0000) GS:ffff930b4e700000(0000) knlGS:0000000000000000 [ 9890.526316] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 9890.526318] CR2: 0000000000000000 CR3: 0000000391c58005 CR4: 00000000001706f0 [ 9890.526321] Call Trace: [ 9890.526324] <TASK> [ 9890.526327] ? show_regs (arch/x86/kernel/dumpstack.c:479) [ 9890.526335] ? __die (arch/x86/kernel/dumpstack.c:421 arch/x86/kernel/dumpstack.c:434) [ 9890.526340] ? page_fault_oops (arch/x86/mm/fault.c:713) [ 9890.526347] ? search_module_extables (kernel/module/main.c:3256 (discriminator ---truncated---

In the Linux kernel, the following vulnerability has been resolved: igb: Fix string truncation warnings in igb_set_fw_version Commit 1978d3ead82c ("intel: fix string truncation warnings") fixes '-Wformat-truncation=' warnings in igb_main.c by using kasprintf. drivers/net/ethernet/intel/igb/igb_main.c:3092:53: warning：‘%d’ directive output may be truncated writing between 1 and 5 bytes into a region of size between 1 and 13 [-Wformat-truncation=] 3092 | "%d.%d, 0x%08x, %d.%d.%d", | ^~ drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note：directive argument in the range [0, 65535] 3092 | "%d.%d, 0x%08x, %d.%d.%d", | ^~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note：directive argument in the range [0, 65535] drivers/net/ethernet/intel/igb/igb_main.c:3090:25: note：‘snprintf’ output between 23 and 43 bytes into a destination of size 32 kasprintf() returns a pointer to dynamically allocated memory which can be NULL upon failure. Fix this warning by using a larger space for adapter->fw_version, and then fall back and continue to use snprintf.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: SHAMPO, Fix invalid WQ linked list unlink When all the strides in a WQE have been consumed, the WQE is unlinked from the WQ linked list (mlx5_wq_ll_pop()). For SHAMPO, it is possible to receive CQEs with 0 consumed strides for the same WQE even after the WQE is fully consumed and unlinked. This triggers an additional unlink for the same wqe which corrupts the linked list. Fix this scenario by accepting 0 sized consumed strides without unlinking the WQE again.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix null pointer deref in dcn20_resource.c Fixes a hang thats triggered when MPV is run on a DCN401 dGPU: mpv --hwdec=vaapi --vo=gpu --hwdec-codecs=all and then enabling fullscreen playback (double click on the video) The following calltrace will be seen: [ 181.843989] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 181.843997] #PF: supervisor instruction fetch in kernel mode [ 181.844003] #PF: error_code(0x0010) - not-present page [ 181.844009] PGD 0 P4D 0 [ 181.844020] Oops: 0010 [#1] PREEMPT SMP NOPTI [ 181.844028] CPU: 6 PID: 1892 Comm: gnome-shell Tainted: G W OE 6.5.0-41-generic #41~22.04.2-Ubuntu [ 181.844038] Hardware name: System manufacturer System Product Name/CROSSHAIR VI HERO, BIOS 6302 10/23/2018 [ 181.844044] RIP: 0010:0x0 [ 181.844079] Code: Unable to access opcode bytes at 0xffffffffffffffd6. [ 181.844084] RSP: 0018:ffffb593c2b8f7b0 EFLAGS: 00010246 [ 181.844093] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000004 [ 181.844099] RDX: ffffb593c2b8f804 RSI: ffffb593c2b8f7e0 RDI: ffff9e3c8e758400 [ 181.844105] RBP: ffffb593c2b8f7b8 R08: ffffb593c2b8f9c8 R09: ffffb593c2b8f96c [ 181.844110] R10: 0000000000000000 R11: 0000000000000000 R12: ffffb593c2b8f9c8 [ 181.844115] R13: 0000000000000001 R14: ffff9e3c88000000 R15: 0000000000000005 [ 181.844121] FS: 00007c6e323bb5c0(0000) GS:ffff9e3f85f80000(0000) knlGS:0000000000000000 [ 181.844128] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 181.844134] CR2: ffffffffffffffd6 CR3: 0000000140fbe000 CR4: 00000000003506e0 [ 181.844141] Call Trace: [ 181.844146] <TASK> [ 181.844153] ? show_regs+0x6d/0x80 [ 181.844167] ? __die+0x24/0x80 [ 181.844179] ? page_fault_oops+0x99/0x1b0 [ 181.844192] ? do_user_addr_fault+0x31d/0x6b0 [ 181.844204] ? exc_page_fault+0x83/0x1b0 [ 181.844216] ? asm_exc_page_fault+0x27/0x30 [ 181.844237] dcn20_get_dcc_compression_cap+0x23/0x30 [amdgpu] [ 181.845115] amdgpu_dm_plane_validate_dcc.constprop.0+0xe5/0x180 [amdgpu] [ 181.845985] amdgpu_dm_plane_fill_plane_buffer_attributes+0x300/0x580 [amdgpu] [ 181.846848] fill_dc_plane_info_and_addr+0x258/0x350 [amdgpu] [ 181.847734] fill_dc_plane_attributes+0x162/0x350 [amdgpu] [ 181.848748] dm_update_plane_state.constprop.0+0x4e3/0x6b0 [amdgpu] [ 181.849791] ? dm_update_plane_state.constprop.0+0x4e3/0x6b0 [amdgpu] [ 181.850840] amdgpu_dm_atomic_check+0xdfe/0x1760 [amdgpu]

In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_acl_erp: Fix object nesting warning ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM (A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can contain more ACLs (i.e., tc filters), but the number of masks in each region (i.e., tc chain) is limited. In order to mitigate the effects of the above limitation, the device allows filters to share a single mask if their masks only differ in up to 8 consecutive bits. For example, dst_ip/25 can be represented using dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the number of masks being used (and therefore does not support mask aggregation), but can contain a limited number of filters. The driver uses the "objagg" library to perform the mask aggregation by passing it objects that consist of the filter's mask and whether the filter is to be inserted into the A-TCAM or the C-TCAM since filters in different TCAMs cannot share a mask. The set of created objects is dependent on the insertion order of the filters and is not necessarily optimal. Therefore, the driver will periodically ask the library to compute a more optimal set ("hints") by looking at all the existing objects. When the library asks the driver whether two objects can be aggregated the driver only compares the provided masks and ignores the A-TCAM / C-TCAM indication. This is the right thing to do since the goal is to move as many filters as possible to the A-TCAM. The driver also forbids two identical masks from being aggregated since this can only happen if one was intentionally put in the C-TCAM to avoid a conflict in the A-TCAM. The above can result in the following set of hints: H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta After getting the hints from the library the driver will start migrating filters from one region to another while consulting the computed hints and instructing the device to perform a lookup in both regions during the transition. Assuming a filter with mask X is being migrated into the A-TCAM in the new region, the hints lookup will return H1. Since H2 is the parent of H1, the library will try to find the object associated with it and create it if necessary in which case another hints lookup (recursive) will be performed. This hints lookup for {mask Y, A-TCAM} will either return H2 or H3 since the driver passes the library an object comparison function that ignores the A-TCAM / C-TCAM indication. This can eventually lead to nested objects which are not supported by the library [1]. Fix by removing the object comparison function from both the driver and the library as the driver was the only user. That way the lookup will only return exact matches. I do not have a reliable reproducer that can reproduce the issue in a timely manner, but before the fix the issue would reproduce in several minutes and with the fix it does not reproduce in over an hour. Note that the current usefulness of the hints is limited because they include the C-TCAM indication and represent aggregation that cannot actually happen. This will be addressed in net-next. [1] WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0 Modules linked in: CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42 Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0 [...] Call Trace: <TASK> __objagg_obj_get+0x2bb/0x580 objagg_obj_get+0xe/0x80 mlxsw_sp_acl_erp_mask_get+0xb5/0xf0 mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0 mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0 mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270 mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510 process_one_work+0x151/0x370

In the Linux kernel, the following vulnerability has been resolved: btrfs: make cow_file_range_inline() honor locked_page on error The btrfs buffered write path runs through __extent_writepage() which has some tricky return value handling for writepage_delalloc(). Specifically, when that returns 1, we exit, but for other return values we continue and end up calling btrfs_folio_end_all_writers(). If the folio has been unlocked (note that we check the PageLocked bit at the start of __extent_writepage()), this results in an assert panic like this one from syzbot: BTRFS: error (device loop0 state EAL) in free_log_tree:3267: errno=-5 IO failure BTRFS warning (device loop0 state EAL): Skipping commit of aborted transaction. BTRFS: error (device loop0 state EAL) in cleanup_transaction:2018: errno=-5 IO failure assertion failed: folio_test_locked(folio), in fs/btrfs/subpage.c:871 ------------[ cut here ]------------ kernel BUG at fs/btrfs/subpage.c:871! Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI CPU: 1 PID: 5090 Comm: syz-executor225 Not tainted 6.10.0-syzkaller-05505-gb1bc554e009e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/27/2024 RIP: 0010:btrfs_folio_end_all_writers+0x55b/0x610 fs/btrfs/subpage.c:871 Code: e9 d3 fb ff ff e8 25 22 c2 fd 48 c7 c7 c0 3c 0e 8c 48 c7 c6 80 3d 0e 8c 48 c7 c2 60 3c 0e 8c b9 67 03 00 00 e8 66 47 ad 07 90 <0f> 0b e8 6e 45 b0 07 4c 89 ff be 08 00 00 00 e8 21 12 25 fe 4c 89 RSP: 0018:ffffc900033d72e0 EFLAGS: 00010246 RAX: 0000000000000045 RBX: 00fff0000000402c RCX: 663b7a08c50a0a00 RDX: 0000000000000000 RSI: 0000000080000000 RDI: 0000000000000000 RBP: ffffc900033d73b0 R08: ffffffff8176b98c R09: 1ffff9200067adfc R10: dffffc0000000000 R11: fffff5200067adfd R12: 0000000000000001 R13: dffffc0000000000 R14: 0000000000000000 R15: ffffea0001cbee80 FS: 0000000000000000(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f5f076012f8 CR3: 000000000e134000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __extent_writepage fs/btrfs/extent_io.c:1597 [inline] extent_write_cache_pages fs/btrfs/extent_io.c:2251 [inline] btrfs_writepages+0x14d7/0x2760 fs/btrfs/extent_io.c:2373 do_writepages+0x359/0x870 mm/page-writeback.c:2656 filemap_fdatawrite_wbc+0x125/0x180 mm/filemap.c:397 __filemap_fdatawrite_range mm/filemap.c:430 [inline] __filemap_fdatawrite mm/filemap.c:436 [inline] filemap_flush+0xdf/0x130 mm/filemap.c:463 btrfs_release_file+0x117/0x130 fs/btrfs/file.c:1547 __fput+0x24a/0x8a0 fs/file_table.c:422 task_work_run+0x24f/0x310 kernel/task_work.c:222 exit_task_work include/linux/task_work.h:40 [inline] do_exit+0xa2f/0x27f0 kernel/exit.c:877 do_group_exit+0x207/0x2c0 kernel/exit.c:1026 __do_sys_exit_group kernel/exit.c:1037 [inline] __se_sys_exit_group kernel/exit.c:1035 [inline] __x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1035 x64_sys_call+0x2634/0x2640 arch/x86/include/generated/asm/syscalls_64.h:232 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f5f075b70c9 Code: Unable to access opcode bytes at 0x7f5f075b709f. I was hitting the same issue by doing hundreds of accelerated runs of generic/475, which also hits IO errors by design. I instrumented that reproducer with bpftrace and found that the undesirable folio_unlock was coming from the following callstack: folio_unlock+5 __process_pages_contig+475 cow_file_range_inline.constprop.0+230 cow_file_range+803 btrfs_run_delalloc_range+566 writepage_delalloc+332 __extent_writepage # inlined in my stacktrace, but I added it here extent_write_cache_pages+622 Looking at the bisected-to pa ---truncated---

In the Linux kernel, the following vulnerability has been resolved: dpll: fix dpll_pin_on_pin_register() for multiple parent pins In scenario where pin is registered with multiple parent pins via dpll_pin_on_pin_register(..), all belonging to the same dpll device. A second call to dpll_pin_on_pin_unregister(..) would cause a call trace, as it tries to use already released registration resources (due to fix introduced in b446631f355e). In this scenario pin was registered twice, so resources are not yet expected to be release until each registered pin/pin pair is unregistered. Currently, the following crash/call trace is produced when ice driver is removed on the system with installed E810T NIC which includes dpll device: WARNING: CPU: 51 PID: 9155 at drivers/dpll/dpll_core.c:809 dpll_pin_ops+0x20/0x30 RIP: 0010:dpll_pin_ops+0x20/0x30 Call Trace: ? __warn+0x7f/0x130 ? dpll_pin_ops+0x20/0x30 dpll_msg_add_pin_freq+0x37/0x1d0 dpll_cmd_pin_get_one+0x1c0/0x400 ? __nlmsg_put+0x63/0x80 dpll_pin_event_send+0x93/0x140 dpll_pin_on_pin_unregister+0x3f/0x100 ice_dpll_deinit_pins+0xa1/0x230 [ice] ice_remove+0xf1/0x210 [ice] Fix by adding a parent pointer as a cookie when creating a registration, also when searching for it. For the regular pins pass NULL, this allows to create separated registration for each parent the pin is registered with.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Fix memory leak in hci_req_sync_complete() In 'hci_req_sync_complete()', always free the previous sync request state before assigning reference to a new one.

In the Linux kernel, the following vulnerability has been resolved: bnxt_en: Fix possible memory leak in bnxt_rdma_aux_device_init() If ulp = kzalloc() fails, the allocated edev will leak because it is not properly assigned and the cleanup path will not be able to free it. Fix it by assigning it properly immediately after allocation.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: reject new basechain after table flag update When dormant flag is toggled, hooks are disabled in the commit phase by iterating over current chains in table (existing and new). The following configuration allows for an inconsistent state: add table x add chain x y { type filter hook input priority 0; } add table x { flags dormant; } add chain x w { type filter hook input priority 1; } which triggers the following warning when trying to unregister chain w which is already unregistered. [ 127.322252] WARNING: CPU: 7 PID: 1211 at net/netfilter/core.c:50 1 __nf_unregister_net_hook+0x21a/0x260 [...] [ 127.322519] Call Trace: [ 127.322521] <TASK> [ 127.322524] ? __warn+0x9f/0x1a0 [ 127.322531] ? __nf_unregister_net_hook+0x21a/0x260 [ 127.322537] ? report_bug+0x1b1/0x1e0 [ 127.322545] ? handle_bug+0x3c/0x70 [ 127.322552] ? exc_invalid_op+0x17/0x40 [ 127.322556] ? asm_exc_invalid_op+0x1a/0x20 [ 127.322563] ? kasan_save_free_info+0x3b/0x60 [ 127.322570] ? __nf_unregister_net_hook+0x6a/0x260 [ 127.322577] ? __nf_unregister_net_hook+0x21a/0x260 [ 127.322583] ? __nf_unregister_net_hook+0x6a/0x260 [ 127.322590] ? __nf_tables_unregister_hook+0x8a/0xe0 [nf_tables] [ 127.322655] nft_table_disable+0x75/0xf0 [nf_tables] [ 127.322717] nf_tables_commit+0x2571/0x2620 [nf_tables]

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: rfi: fix potential response leaks If the rx payload length check fails, or if kmemdup() fails, we still need to free the command response. Fix that.