In the Linux kernel, the following vulnerability has been resolved: dma-debug: don't call __dma_entry_alloc_check_leak() under free_entries_lock __dma_entry_alloc_check_leak() calls into printk -> serial console output (qcom geni) and grabs port->lock under free_entries_lock spin lock, which is a reverse locking dependency chain as qcom_geni IRQ handler can call into dma-debug code and grab free_entries_lock under port->lock. Move __dma_entry_alloc_check_leak() call out of free_entries_lock scope so that we don't acquire serial console's port->lock under it. Trimmed-down lockdep splat: The existing dependency chain (in reverse order) is: -> #2 (free_entries_lock){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 dma_entry_alloc+0x38/0x110 debug_dma_map_page+0x60/0xf8 dma_map_page_attrs+0x1e0/0x230 dma_map_single_attrs.constprop.0+0x6c/0xc8 geni_se_rx_dma_prep+0x40/0xcc qcom_geni_serial_isr+0x310/0x510 __handle_irq_event_percpu+0x110/0x244 handle_irq_event_percpu+0x20/0x54 handle_irq_event+0x50/0x88 handle_fasteoi_irq+0xa4/0xcc handle_irq_desc+0x28/0x40 generic_handle_domain_irq+0x24/0x30 gic_handle_irq+0xc4/0x148 do_interrupt_handler+0xa4/0xb0 el1_interrupt+0x34/0x64 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x64/0x68 arch_local_irq_enable+0x4/0x8 ____do_softirq+0x18/0x24 ... -> #1 (&port_lock_key){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 qcom_geni_serial_console_write+0x184/0x1dc console_flush_all+0x344/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 register_console+0x230/0x38c uart_add_one_port+0x338/0x494 qcom_geni_serial_probe+0x390/0x424 platform_probe+0x70/0xc0 really_probe+0x148/0x280 __driver_probe_device+0xfc/0x114 driver_probe_device+0x44/0x100 __device_attach_driver+0x64/0xdc bus_for_each_drv+0xb0/0xd8 __device_attach+0xe4/0x140 device_initial_probe+0x1c/0x28 bus_probe_device+0x44/0xb0 device_add+0x538/0x668 of_device_add+0x44/0x50 of_platform_device_create_pdata+0x94/0xc8 of_platform_bus_create+0x270/0x304 of_platform_populate+0xac/0xc4 devm_of_platform_populate+0x60/0xac geni_se_probe+0x154/0x160 platform_probe+0x70/0xc0 ... -> #0 (console_owner){-...}-{0:0}: __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 dma_entry_alloc+0xb4/0x110 debug_dma_map_sg+0xdc/0x2f8 __dma_map_sg_attrs+0xac/0xe4 dma_map_sgtable+0x30/0x4c get_pages+0x1d4/0x1e4 [msm] msm_gem_pin_pages_locked+0x38/0xac [msm] msm_gem_pin_vma_locked+0x58/0x88 [msm] msm_ioctl_gem_submit+0xde4/0x13ac [msm] drm_ioctl_kernel+0xe0/0x15c drm_ioctl+0x2e8/0x3f4 vfs_ioctl+0x30/0x50 ... Chain exists of: console_owner --> &port_lock_key --> free_entries_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(free_entries_lock); lock(&port_lock_key); lock(free_entries_lock); lock(console_owner); *** DEADLOCK *** Call trace: dump_backtrace+0xb4/0xf0 show_stack+0x20/0x30 dump_stack_lvl+0x60/0x84 dump_stack+0x18/0x24 print_circular_bug+0x1cc/0x234 check_noncircular+0x78/0xac __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 consol ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm: Don't unref the same fb many times by mistake due to deadlock handling If we get a deadlock after the fb lookup in drm_mode_page_flip_ioctl() we proceed to unref the fb and then retry the whole thing from the top. But we forget to reset the fb pointer back to NULL, and so if we then get another error during the retry, before the fb lookup, we proceed the unref the same fb again without having gotten another reference. The end result is that the fb will (eventually) end up being freed while it's still in use. Reset fb to NULL once we've unreffed it to avoid doing it again until we've done another fb lookup. This turned out to be pretty easy to hit on a DG2 when doing async flips (and CONFIG_DEBUG_WW_MUTEX_SLOWPATH=y). The first symptom I saw that drm_closefb() simply got stuck in a busy loop while walking the framebuffer list. Fortunately I was able to convince it to oops instead, and from there it was easier to track down the culprit.

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: Drop chan lock before queuing buffers Ensure read and write locks for the channel are not taken in succession by dropping the read lock from parse_xfer_event() such that a callback given to client can potentially queue buffers and acquire the write lock in that process. Any queueing of buffers should be done without channel read lock acquired as it can result in multiple locks and a soft lockup. [mani: added fixes tag and cc'ed stable]

In the Linux kernel, the following vulnerability has been resolved: can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock The following 3 locks would race against each other, causing the deadlock situation in the Syzbot bug report: - j1939_socks_lock - active_session_list_lock - sk_session_queue_lock A reasonable fix is to change j1939_socks_lock to an rwlock, since in the rare situations where a write lock is required for the linked list that j1939_socks_lock is protecting, the code does not attempt to acquire any more locks. This would break the circular lock dependency, where, for example, the current thread already locks j1939_socks_lock and attempts to acquire sk_session_queue_lock, and at the same time, another thread attempts to acquire j1939_socks_lock while holding sk_session_queue_lock. NOTE: This patch along does not fix the unregister_netdevice bug reported by Syzbot; instead, it solves a deadlock situation to prepare for one or more further patches to actually fix the Syzbot bug, which appears to be a reference counting problem within the j1939 codebase. [mkl: remove unrelated newline change]

In the Linux kernel, the following vulnerability has been resolved: ceph: fix deadlock or deadcode of misusing dget() The lock order is incorrect between denty and its parent, we should always make sure that the parent get the lock first. But since this deadcode is never used and the parent dir will always be set from the callers, let's just remove it.

In the Linux kernel, the following vulnerability has been resolved: tcp: correct handling of extreme memory squeeze Testing with iperf3 using the "pasta" protocol splicer has revealed a problem in the way tcp handles window advertising in extreme memory squeeze situations. Under memory pressure, a socket endpoint may temporarily advertise a zero-sized window, but this is not stored as part of the socket data. The reasoning behind this is that it is considered a temporary setting which shouldn't influence any further calculations. However, if we happen to stall at an unfortunate value of the current window size, the algorithm selecting a new value will consistently fail to advertise a non-zero window once we have freed up enough memory. This means that this side's notion of the current window size is different from the one last advertised to the peer, causing the latter to not send any data to resolve the sitution. The problem occurs on the iperf3 server side, and the socket in question is a completely regular socket with the default settings for the fedora40 kernel. We do not use SO_PEEK or SO_RCVBUF on the socket. The following excerpt of a logging session, with own comments added, shows more in detail what is happening: // tcp_v4_rcv(->) // tcp_rcv_established(->) [5201<->39222]: ==== Activating log @ net/ipv4/tcp_input.c/tcp_data_queue()/5257 ==== [5201<->39222]: tcp_data_queue(->) [5201<->39222]: DROPPING skb [265600160..265665640], reason: SKB_DROP_REASON_PROTO_MEM [rcv_nxt 265600160, rcv_wnd 262144, snt_ack 265469200, win_now 131184] [copied_seq 259909392->260034360 (124968), unread 5565800, qlen 85, ofoq 0] [OFO queue: gap: 65480, len: 0] [5201<->39222]: tcp_data_queue(<-) [5201<->39222]: __tcp_transmit_skb(->) [tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160] [5201<->39222]: tcp_select_window(->) [5201<->39222]: (inet_csk(sk)->icsk_ack.pending & ICSK_ACK_NOMEM) ? --> TRUE [tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160] returning 0 [5201<->39222]: tcp_select_window(<-) [5201<->39222]: ADVERTISING WIN 0, ACK_SEQ: 265600160 [5201<->39222]: [__tcp_transmit_skb(<-) [5201<->39222]: tcp_rcv_established(<-) [5201<->39222]: tcp_v4_rcv(<-) // Receive queue is at 85 buffers and we are out of memory. // We drop the incoming buffer, although it is in sequence, and decide // to send an advertisement with a window of zero. // We don't update tp->rcv_wnd and tp->rcv_wup accordingly, which means // we unconditionally shrink the window. [5201<->39222]: tcp_recvmsg_locked(->) [5201<->39222]: __tcp_cleanup_rbuf(->) tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160 [5201<->39222]: [new_win = 0, win_now = 131184, 2 * win_now = 262368] [5201<->39222]: [new_win >= (2 * win_now) ? --> time_to_ack = 0] [5201<->39222]: NOT calling tcp_send_ack() [tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160] [5201<->39222]: __tcp_cleanup_rbuf(<-) [rcv_nxt 265600160, rcv_wnd 262144, snt_ack 265469200, win_now 131184] [copied_seq 260040464->260040464 (0), unread 5559696, qlen 85, ofoq 0] returning 6104 bytes [5201<->39222]: tcp_recvmsg_locked(<-) // After each read, the algorithm for calculating the new receive // window in __tcp_cleanup_rbuf() finds it is too small to advertise // or to update tp->rcv_wnd. // Meanwhile, the peer thinks the window is zero, and will not send // any more data to trigger an update from the interrupt mode side. [5201<->39222]: tcp_recvmsg_locked(->) [5201<->39222]: __tcp_cleanup_rbuf(->) tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160 [5201<->39222]: [new_win = 262144, win_now = 131184, 2 * win_n ---truncated---

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix potential deadloop in prepare_compress_overwrite() Jan Prusakowski reported a kernel hang issue as below: When running xfstests on linux-next kernel (6.14.0-rc3, 6.12) I encountered a problem in generic/475 test where fsstress process gets blocked in __f2fs_write_data_pages() and the test hangs. The options I used are: MKFS_OPTIONS -- -O compression -O extra_attr -O project_quota -O quota /dev/vdc MOUNT_OPTIONS -- -o acl,user_xattr -o discard,compress_extension=* /dev/vdc /vdc INFO: task kworker/u8:0:11 blocked for more than 122 seconds. Not tainted 6.14.0-rc3-xfstests-lockdep #1 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u8:0 state:D stack:0 pid:11 tgid:11 ppid:2 task_flags:0x4208160 flags:0x00004000 Workqueue: writeback wb_workfn (flush-253:0) Call Trace: <TASK> __schedule+0x309/0x8e0 schedule+0x3a/0x100 schedule_preempt_disabled+0x15/0x30 __mutex_lock+0x59a/0xdb0 __f2fs_write_data_pages+0x3ac/0x400 do_writepages+0xe8/0x290 __writeback_single_inode+0x5c/0x360 writeback_sb_inodes+0x22f/0x570 wb_writeback+0xb0/0x410 wb_do_writeback+0x47/0x2f0 wb_workfn+0x5a/0x1c0 process_one_work+0x223/0x5b0 worker_thread+0x1d5/0x3c0 kthread+0xfd/0x230 ret_from_fork+0x31/0x50 ret_from_fork_asm+0x1a/0x30 </TASK> The root cause is: once generic/475 starts toload error table to dm device, f2fs_prepare_compress_overwrite() will loop reading compressed cluster pages due to IO error, meanwhile it has held .writepages lock, it can block all other writeback tasks. Let's fix this issue w/ below changes: - add f2fs_handle_page_eio() in prepare_compress_overwrite() to detect IO error. - detect cp_error earler in f2fs_read_multi_pages().

In the Linux kernel, the following vulnerability has been resolved: PCI: vmd: Make vmd_dev::cfg_lock a raw_spinlock_t type The access to the PCI config space via pci_ops::read and pci_ops::write is a low-level hardware access. The functions can be accessed with disabled interrupts even on PREEMPT_RT. The pci_lock is a raw_spinlock_t for this purpose. A spinlock_t becomes a sleeping lock on PREEMPT_RT, so it cannot be acquired with disabled interrupts. The vmd_dev::cfg_lock is accessed in the same context as the pci_lock. Make vmd_dev::cfg_lock a raw_spinlock_t type so it can be used with interrupts disabled. This was reported as: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 Call Trace: rt_spin_lock+0x4e/0x130 vmd_pci_read+0x8d/0x100 [vmd] pci_user_read_config_byte+0x6f/0xe0 pci_read_config+0xfe/0x290 sysfs_kf_bin_read+0x68/0x90 [bigeasy: reword commit message] Tested-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com> [kwilczynski: commit log] [bhelgaas: add back report info from https://lore.kernel.org/lkml/20241218115951.83062-1-ryotkkr98@gmail.com/]

In the Linux kernel, the following vulnerability has been resolved: bus: mhi: host: pci_generic: Use pci_try_reset_function() to avoid deadlock There are multiple places from where the recovery work gets scheduled asynchronously. Also, there are multiple places where the caller waits synchronously for the recovery to be completed. One such place is during the PM shutdown() callback. If the device is not alive during recovery_work, it will try to reset the device using pci_reset_function(). This function internally will take the device_lock() first before resetting the device. By this time, if the lock has already been acquired, then recovery_work will get stalled while waiting for the lock. And if the lock was already acquired by the caller which waits for the recovery_work to be completed, it will lead to deadlock. This is what happened on the X1E80100 CRD device when the device died before shutdown() callback. Driver core calls the driver's shutdown() callback while holding the device_lock() leading to deadlock. And this deadlock scenario can occur on other paths as well, like during the PM suspend() callback, where the driver core would hold the device_lock() before calling driver's suspend() callback. And if the recovery_work was already started, it could lead to deadlock. This is also observed on the X1E80100 CRD. So to fix both issues, use pci_try_reset_function() in recovery_work. This function first checks for the availability of the device_lock() before trying to reset the device. If the lock is available, it will acquire it and reset the device. Otherwise, it will return -EAGAIN. If that happens, recovery_work will fail with the error message "Recovery failed" as not much could be done.

In the Linux kernel, the following vulnerability has been resolved: gpio: rcar: Use raw_spinlock to protect register access Use raw_spinlock in order to fix spurious messages about invalid context when spinlock debugging is enabled. The lock is only used to serialize register access. [ 4.239592] ============================= [ 4.239595] [ BUG: Invalid wait context ] [ 4.239599] 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 Not tainted [ 4.239603] ----------------------------- [ 4.239606] kworker/u8:5/76 is trying to lock: [ 4.239609] ffff0000091898a0 (&p->lock){....}-{3:3}, at: gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.239641] other info that might help us debug this: [ 4.239643] context-{5:5} [ 4.239646] 5 locks held by kworker/u8:5/76: [ 4.239651] #0: ffff0000080fb148 ((wq_completion)async){+.+.}-{0:0}, at: process_one_work+0x190/0x62c [ 4.250180] OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value. [ 4.254094] #1: ffff80008299bd80 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x1b8/0x62c [ 4.254109] #2: ffff00000920c8f8 [ 4.258345] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'bitclock-master' with a value. [ 4.264803] (&dev->mutex){....}-{4:4}, at: __device_attach_async_helper+0x3c/0xdc [ 4.264820] #3: ffff00000a50ca40 (request_class#2){+.+.}-{4:4}, at: __setup_irq+0xa0/0x690 [ 4.264840] #4: [ 4.268872] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'frame-master' with a value. [ 4.273275] ffff00000a50c8c8 (lock_class){....}-{2:2}, at: __setup_irq+0xc4/0x690 [ 4.296130] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz [ 4.304082] stack backtrace: [ 4.304086] CPU: 1 UID: 0 PID: 76 Comm: kworker/u8:5 Not tainted 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 [ 4.304092] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 4.304097] Workqueue: async async_run_entry_fn [ 4.304106] Call trace: [ 4.304110] show_stack+0x14/0x20 (C) [ 4.304122] dump_stack_lvl+0x6c/0x90 [ 4.304131] dump_stack+0x14/0x1c [ 4.304138] __lock_acquire+0xdfc/0x1584 [ 4.426274] lock_acquire+0x1c4/0x33c [ 4.429942] _raw_spin_lock_irqsave+0x5c/0x80 [ 4.434307] gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.440061] gpio_rcar_irq_set_type+0xd4/0xd8 [ 4.444422] __irq_set_trigger+0x5c/0x178 [ 4.448435] __setup_irq+0x2e4/0x690 [ 4.452012] request_threaded_irq+0xc4/0x190 [ 4.456285] devm_request_threaded_irq+0x7c/0xf4 [ 4.459398] ata1: link resume succeeded after 1 retries [ 4.460902] mmc_gpiod_request_cd_irq+0x68/0xe0 [ 4.470660] mmc_start_host+0x50/0xac [ 4.474327] mmc_add_host+0x80/0xe4 [ 4.477817] tmio_mmc_host_probe+0x2b0/0x440 [ 4.482094] renesas_sdhi_probe+0x488/0x6f4 [ 4.486281] renesas_sdhi_internal_dmac_probe+0x60/0x78 [ 4.491509] platform_probe+0x64/0xd8 [ 4.495178] really_probe+0xb8/0x2a8 [ 4.498756] __driver_probe_device+0x74/0x118 [ 4.503116] driver_probe_device+0x3c/0x154 [ 4.507303] __device_attach_driver+0xd4/0x160 [ 4.511750] bus_for_each_drv+0x84/0xe0 [ 4.515588] __device_attach_async_helper+0xb0/0xdc [ 4.520470] async_run_entry_fn+0x30/0xd8 [ 4.524481] process_one_work+0x210/0x62c [ 4.528494] worker_thread+0x1ac/0x340 [ 4.532245] kthread+0x10c/0x110 [ 4.535476] ret_from_fork+0x10/0x20

In the Linux kernel, the following vulnerability has been resolved: block: mark GFP_NOIO around sysfs ->store() sysfs ->store is called with queue freezed, meantime we have several ->store() callbacks(update_nr_requests, wbt, scheduler) to allocate memory with GFP_KERNEL which may run into direct reclaim code path, then potential deadlock can be caused. Fix the issue by marking NOIO around sysfs ->store()

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Use spin_lock_irqsave() in interruptible context spin_lock/unlock() functions used in interrupt contexts could result in a deadlock, as seen in GitLab issue #13399, which occurs when interrupt comes in while holding a lock. Try to remedy the problem by saving irq state before spin lock acquisition. v2: add irqs' state save/restore calls to all locks/unlocks in signal_irq_work() execution (Maciej) v3: use with spin_lock_irqsave() in guc_lrc_desc_unpin() instead of other lock/unlock calls and add Fixes and Cc tags (Tvrtko); change title and commit message (cherry picked from commit c088387ddd6482b40f21ccf23db1125e8fa4af7e)

In the Linux kernel, the following vulnerability has been resolved: net: rose: lock the socket in rose_bind() syzbot reported a soft lockup in rose_loopback_timer(), with a repro calling bind() from multiple threads. rose_bind() must lock the socket to avoid this issue.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Add a lock when accessing the buddy trim function When running YouTube videos and Steam games simultaneously, the tester found a system hang / race condition issue with the multi-display configuration setting. Adding a lock to the buddy allocator's trim function would be the solution. <log snip> [ 7197.250436] general protection fault, probably for non-canonical address 0xdead000000000108 [ 7197.250447] RIP: 0010:__alloc_range+0x8b/0x340 [amddrm_buddy] [ 7197.250470] Call Trace: [ 7197.250472] <TASK> [ 7197.250475] ? show_regs+0x6d/0x80 [ 7197.250481] ? die_addr+0x37/0xa0 [ 7197.250483] ? exc_general_protection+0x1db/0x480 [ 7197.250488] ? drm_suballoc_new+0x13c/0x93d [drm_suballoc_helper] [ 7197.250493] ? asm_exc_general_protection+0x27/0x30 [ 7197.250498] ? __alloc_range+0x8b/0x340 [amddrm_buddy] [ 7197.250501] ? __alloc_range+0x109/0x340 [amddrm_buddy] [ 7197.250506] amddrm_buddy_block_trim+0x1b5/0x260 [amddrm_buddy] [ 7197.250511] amdgpu_vram_mgr_new+0x4f5/0x590 [amdgpu] [ 7197.250682] amdttm_resource_alloc+0x46/0xb0 [amdttm] [ 7197.250689] ttm_bo_alloc_resource+0xe4/0x370 [amdttm] [ 7197.250696] amdttm_bo_validate+0x9d/0x180 [amdttm] [ 7197.250701] amdgpu_bo_pin+0x15a/0x2f0 [amdgpu] [ 7197.250831] amdgpu_dm_plane_helper_prepare_fb+0xb2/0x360 [amdgpu] [ 7197.251025] ? try_wait_for_completion+0x59/0x70 [ 7197.251030] drm_atomic_helper_prepare_planes.part.0+0x2f/0x1e0 [ 7197.251035] drm_atomic_helper_prepare_planes+0x5d/0x70 [ 7197.251037] drm_atomic_helper_commit+0x84/0x160 [ 7197.251040] drm_atomic_nonblocking_commit+0x59/0x70 [ 7197.251043] drm_mode_atomic_ioctl+0x720/0x850 [ 7197.251047] ? __pfx_drm_mode_atomic_ioctl+0x10/0x10 [ 7197.251049] drm_ioctl_kernel+0xb9/0x120 [ 7197.251053] ? srso_alias_return_thunk+0x5/0xfbef5 [ 7197.251056] drm_ioctl+0x2d4/0x550 [ 7197.251058] ? __pfx_drm_mode_atomic_ioctl+0x10/0x10 [ 7197.251063] amdgpu_drm_ioctl+0x4e/0x90 [amdgpu] [ 7197.251186] __x64_sys_ioctl+0xa0/0xf0 [ 7197.251190] x64_sys_call+0x143b/0x25c0 [ 7197.251193] do_syscall_64+0x7f/0x180 [ 7197.251197] ? srso_alias_return_thunk+0x5/0xfbef5 [ 7197.251199] ? amdgpu_display_user_framebuffer_create+0x215/0x320 [amdgpu] [ 7197.251329] ? drm_internal_framebuffer_create+0xb7/0x1a0 [ 7197.251332] ? srso_alias_return_thunk+0x5/0xfbef5 (cherry picked from commit 3318ba94e56b9183d0304577c74b33b6b01ce516)

In the Linux kernel, the following vulnerability has been resolved: bpf: bpf_local_storage: Always use bpf_mem_alloc in PREEMPT_RT In PREEMPT_RT, kmalloc(GFP_ATOMIC) is still not safe in non preemptible context. bpf_mem_alloc must be used in PREEMPT_RT. This patch is to enforce bpf_mem_alloc in the bpf_local_storage when CONFIG_PREEMPT_RT is enabled. [ 35.118559] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 [ 35.118566] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1832, name: test_progs [ 35.118569] preempt_count: 1, expected: 0 [ 35.118571] RCU nest depth: 1, expected: 1 [ 35.118577] INFO: lockdep is turned off. ... [ 35.118647] __might_resched+0x433/0x5b0 [ 35.118677] rt_spin_lock+0xc3/0x290 [ 35.118700] ___slab_alloc+0x72/0xc40 [ 35.118723] __kmalloc_noprof+0x13f/0x4e0 [ 35.118732] bpf_map_kzalloc+0xe5/0x220 [ 35.118740] bpf_selem_alloc+0x1d2/0x7b0 [ 35.118755] bpf_local_storage_update+0x2fa/0x8b0 [ 35.118784] bpf_sk_storage_get_tracing+0x15a/0x1d0 [ 35.118791] bpf_prog_9a118d86fca78ebb_trace_inet_sock_set_state+0x44/0x66 [ 35.118795] bpf_trace_run3+0x222/0x400 [ 35.118820] __bpf_trace_inet_sock_set_state+0x11/0x20 [ 35.118824] trace_inet_sock_set_state+0x112/0x130 [ 35.118830] inet_sk_state_store+0x41/0x90 [ 35.118836] tcp_set_state+0x3b3/0x640 There is no need to adjust the gfp_flags passing to the bpf_mem_cache_alloc_flags() which only honors the GFP_KERNEL. The verifier has ensured GFP_KERNEL is passed only in sleepable context. It has been an old issue since the first introduction of the bpf_local_storage ~5 years ago, so this patch targets the bpf-next. bpf_mem_alloc is needed to solve it, so the Fixes tag is set to the commit when bpf_mem_alloc was first used in the bpf_local_storage.

In the Linux kernel, the following vulnerability has been resolved: rhashtable: Fix potential deadlock by moving schedule_work outside lock Move the hash table growth check and work scheduling outside the rht lock to prevent a possible circular locking dependency. The original implementation could trigger a lockdep warning due to a potential deadlock scenario involving nested locks between rhashtable bucket, rq lock, and dsq lock. By relocating the growth check and work scheduling after releasing the rth lock, we break this potential deadlock chain. This change expands the flexibility of rhashtable by removing restrictive locking that previously limited its use in scheduler and workqueue contexts. Import to say that this calls rht_grow_above_75(), which reads from struct rhashtable without holding the lock, if this is a problem, we can move the check to the lock, and schedule the workqueue after the lock. Modified so that atomic_inc is also moved outside of the bucket lock along with the growth above 75% check.

In the Linux kernel, the following vulnerability has been resolved: bpf: fix recursive lock when verdict program return SK_PASS When the stream_verdict program returns SK_PASS, it places the received skb into its own receive queue, but a recursive lock eventually occurs, leading to an operating system deadlock. This issue has been present since v6.9. ''' sk_psock_strp_data_ready write_lock_bh(&sk->sk_callback_lock) strp_data_ready strp_read_sock read_sock -> tcp_read_sock strp_recv cb.rcv_msg -> sk_psock_strp_read # now stream_verdict return SK_PASS without peer sock assign __SK_PASS = sk_psock_map_verd(SK_PASS, NULL) sk_psock_verdict_apply sk_psock_skb_ingress_self sk_psock_skb_ingress_enqueue sk_psock_data_ready read_lock_bh(&sk->sk_callback_lock) <= dead lock ''' This topic has been discussed before, but it has not been fixed. Previous discussion: https://lore.kernel.org/all/6684a5864ec86_403d20898@john.notmuch

In the Linux kernel, the following vulnerability has been resolved: mm/vmalloc: combine all TLB flush operations of KASAN shadow virtual address into one operation When compiling kernel source 'make -j $(nproc)' with the up-and-running KASAN-enabled kernel on a 256-core machine, the following soft lockup is shown: watchdog: BUG: soft lockup - CPU#28 stuck for 22s! [kworker/28:1:1760] CPU: 28 PID: 1760 Comm: kworker/28:1 Kdump: loaded Not tainted 6.10.0-rc5 #95 Workqueue: events drain_vmap_area_work RIP: 0010:smp_call_function_many_cond+0x1d8/0xbb0 Code: 38 c8 7c 08 84 c9 0f 85 49 08 00 00 8b 45 08 a8 01 74 2e 48 89 f1 49 89 f7 48 c1 e9 03 41 83 e7 07 4c 01 e9 41 83 c7 03 f3 90 <0f> b6 01 41 38 c7 7c 08 84 c0 0f 85 d4 06 00 00 8b 45 08 a8 01 75 RSP: 0018:ffffc9000cb3fb60 EFLAGS: 00000202 RAX: 0000000000000011 RBX: ffff8883bc4469c0 RCX: ffffed10776e9949 RDX: 0000000000000002 RSI: ffff8883bb74ca48 RDI: ffffffff8434dc50 RBP: ffff8883bb74ca40 R08: ffff888103585dc0 R09: ffff8884533a1800 R10: 0000000000000004 R11: ffffffffffffffff R12: ffffed1077888d39 R13: dffffc0000000000 R14: ffffed1077888d38 R15: 0000000000000003 FS: 0000000000000000(0000) GS:ffff8883bc400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00005577b5c8d158 CR3: 0000000004850000 CR4: 0000000000350ef0 Call Trace: <IRQ> ? watchdog_timer_fn+0x2cd/0x390 ? __pfx_watchdog_timer_fn+0x10/0x10 ? __hrtimer_run_queues+0x300/0x6d0 ? sched_clock_cpu+0x69/0x4e0 ? __pfx___hrtimer_run_queues+0x10/0x10 ? srso_return_thunk+0x5/0x5f ? ktime_get_update_offsets_now+0x7f/0x2a0 ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? hrtimer_interrupt+0x2ca/0x760 ? __sysvec_apic_timer_interrupt+0x8c/0x2b0 ? sysvec_apic_timer_interrupt+0x6a/0x90 </IRQ> <TASK> ? asm_sysvec_apic_timer_interrupt+0x16/0x20 ? smp_call_function_many_cond+0x1d8/0xbb0 ? __pfx_do_kernel_range_flush+0x10/0x10 on_each_cpu_cond_mask+0x20/0x40 flush_tlb_kernel_range+0x19b/0x250 ? srso_return_thunk+0x5/0x5f ? kasan_release_vmalloc+0xa7/0xc0 purge_vmap_node+0x357/0x820 ? __pfx_purge_vmap_node+0x10/0x10 __purge_vmap_area_lazy+0x5b8/0xa10 drain_vmap_area_work+0x21/0x30 process_one_work+0x661/0x10b0 worker_thread+0x844/0x10e0 ? srso_return_thunk+0x5/0x5f ? __kthread_parkme+0x82/0x140 ? __pfx_worker_thread+0x10/0x10 kthread+0x2a5/0x370 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x30/0x70 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> Debugging Analysis: 1. The following ftrace log shows that the lockup CPU spends too much time iterating vmap_nodes and flushing TLB when purging vm_area structures. (Some info is trimmed). kworker: funcgraph_entry: | drain_vmap_area_work() { kworker: funcgraph_entry: | mutex_lock() { kworker: funcgraph_entry: 1.092 us | __cond_resched(); kworker: funcgraph_exit: 3.306 us | } ... ... kworker: funcgraph_entry: | flush_tlb_kernel_range() { ... ... kworker: funcgraph_exit: # 7533.649 us | } ... ... kworker: funcgraph_entry: 2.344 us | mutex_unlock(); kworker: funcgraph_exit: $ 23871554 us | } The drain_vmap_area_work() spends over 23 seconds. There are 2805 flush_tlb_kernel_range() calls in the ftrace log. * One is called in __purge_vmap_area_lazy(). * Others are called by purge_vmap_node->kasan_release_vmalloc. purge_vmap_node() iteratively releases kasan vmalloc allocations and flushes TLB for each vmap_area. - [Rough calculation] Each flush_tlb_kernel_range() runs about 7.5ms. -- 2804 * 7.5ms = 21.03 seconds. -- That's why a soft lock is triggered. 2. Extending the soft lockup time can work around the issue (For example, # echo ---truncated---

In the Linux kernel, the following vulnerability has been resolved: rxrpc, afs: Fix peer hash locking vs RCU callback In its address list, afs now retains pointers to and refs on one or more rxrpc_peer objects. The address list is freed under RCU and at this time, it puts the refs on those peers. Now, when an rxrpc_peer object runs out of refs, it gets removed from the peer hash table and, for that, rxrpc has to take a spinlock. However, it is now being called from afs's RCU cleanup, which takes place in BH context - but it is just taking an ordinary spinlock. The put may also be called from non-BH context, and so there exists the possibility of deadlock if the BH-based RCU cleanup happens whilst the hash spinlock is held. This led to the attached lockdep complaint. Fix this by changing spinlocks of rxnet->peer_hash_lock back to BH-disabling locks. ================================ WARNING: inconsistent lock state 6.13.0-rc5-build2+ #1223 Tainted: G E -------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. swapper/1/0 [HC0[0]:SC1[1]:HE1:SE0] takes: ffff88810babe228 (&rxnet->peer_hash_lock){+.?.}-{3:3}, at: rxrpc_put_peer+0xcb/0x180 {SOFTIRQ-ON-W} state was registered at: mark_usage+0x164/0x180 __lock_acquire+0x544/0x990 lock_acquire.part.0+0x103/0x280 _raw_spin_lock+0x2f/0x40 rxrpc_peer_keepalive_worker+0x144/0x440 process_one_work+0x486/0x7c0 process_scheduled_works+0x73/0x90 worker_thread+0x1c8/0x2a0 kthread+0x19b/0x1b0 ret_from_fork+0x24/0x40 ret_from_fork_asm+0x1a/0x30 irq event stamp: 972402 hardirqs last enabled at (972402): [<ffffffff8244360e>] _raw_spin_unlock_irqrestore+0x2e/0x50 hardirqs last disabled at (972401): [<ffffffff82443328>] _raw_spin_lock_irqsave+0x18/0x60 softirqs last enabled at (972300): [<ffffffff810ffbbe>] handle_softirqs+0x3ee/0x430 softirqs last disabled at (972313): [<ffffffff810ffc54>] __irq_exit_rcu+0x44/0x110 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&rxnet->peer_hash_lock); <Interrupt> lock(&rxnet->peer_hash_lock); *** DEADLOCK *** 1 lock held by swapper/1/0: #0: ffffffff83576be0 (rcu_callback){....}-{0:0}, at: rcu_lock_acquire+0x7/0x30 stack backtrace: CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Tainted: G E 6.13.0-rc5-build2+ #1223 Tainted: [E]=UNSIGNED_MODULE Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014 Call Trace: <IRQ> dump_stack_lvl+0x57/0x80 print_usage_bug.part.0+0x227/0x240 valid_state+0x53/0x70 mark_lock_irq+0xa5/0x2f0 mark_lock+0xf7/0x170 mark_usage+0xe1/0x180 __lock_acquire+0x544/0x990 lock_acquire.part.0+0x103/0x280 _raw_spin_lock+0x2f/0x40 rxrpc_put_peer+0xcb/0x180 afs_free_addrlist+0x46/0x90 [kafs] rcu_do_batch+0x2d2/0x640 rcu_core+0x2f7/0x350 handle_softirqs+0x1ee/0x430 __irq_exit_rcu+0x44/0x110 irq_exit_rcu+0xa/0x30 sysvec_apic_timer_interrupt+0x7f/0xa0 </IRQ>

An issue was discovered in the Linux kernel through 5.6.11. btree_gc_coalesce in drivers/md/bcache/btree.c has a deadlock if a coalescing operation fails.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: iso: Fix circular lock in iso_conn_big_sync This fixes the circular locking dependency warning below, by reworking iso_sock_recvmsg, to ensure that the socket lock is always released before calling a function that locks hdev. [ 561.670344] ====================================================== [ 561.670346] WARNING: possible circular locking dependency detected [ 561.670349] 6.12.0-rc6+ #26 Not tainted [ 561.670351] ------------------------------------------------------ [ 561.670353] iso-tester/3289 is trying to acquire lock: [ 561.670355] ffff88811f600078 (&hdev->lock){+.+.}-{3:3}, at: iso_conn_big_sync+0x73/0x260 [bluetooth] [ 561.670405] but task is already holding lock: [ 561.670407] ffff88815af58258 (sk_lock-AF_BLUETOOTH){+.+.}-{0:0}, at: iso_sock_recvmsg+0xbf/0x500 [bluetooth] [ 561.670450] which lock already depends on the new lock. [ 561.670452] the existing dependency chain (in reverse order) is: [ 561.670453] -> #2 (sk_lock-AF_BLUETOOTH){+.+.}-{0:0}: [ 561.670458] lock_acquire+0x7c/0xc0 [ 561.670463] lock_sock_nested+0x3b/0xf0 [ 561.670467] bt_accept_dequeue+0x1a5/0x4d0 [bluetooth] [ 561.670510] iso_sock_accept+0x271/0x830 [bluetooth] [ 561.670547] do_accept+0x3dd/0x610 [ 561.670550] __sys_accept4+0xd8/0x170 [ 561.670553] __x64_sys_accept+0x74/0xc0 [ 561.670556] x64_sys_call+0x17d6/0x25f0 [ 561.670559] do_syscall_64+0x87/0x150 [ 561.670563] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670567] -> #1 (sk_lock-AF_BLUETOOTH-BTPROTO_ISO){+.+.}-{0:0}: [ 561.670571] lock_acquire+0x7c/0xc0 [ 561.670574] lock_sock_nested+0x3b/0xf0 [ 561.670577] iso_sock_listen+0x2de/0xf30 [bluetooth] [ 561.670617] __sys_listen_socket+0xef/0x130 [ 561.670620] __x64_sys_listen+0xe1/0x190 [ 561.670623] x64_sys_call+0x2517/0x25f0 [ 561.670626] do_syscall_64+0x87/0x150 [ 561.670629] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670632] -> #0 (&hdev->lock){+.+.}-{3:3}: [ 561.670636] __lock_acquire+0x32ad/0x6ab0 [ 561.670639] lock_acquire.part.0+0x118/0x360 [ 561.670642] lock_acquire+0x7c/0xc0 [ 561.670644] __mutex_lock+0x18d/0x12f0 [ 561.670647] mutex_lock_nested+0x1b/0x30 [ 561.670651] iso_conn_big_sync+0x73/0x260 [bluetooth] [ 561.670687] iso_sock_recvmsg+0x3e9/0x500 [bluetooth] [ 561.670722] sock_recvmsg+0x1d5/0x240 [ 561.670725] sock_read_iter+0x27d/0x470 [ 561.670727] vfs_read+0x9a0/0xd30 [ 561.670731] ksys_read+0x1a8/0x250 [ 561.670733] __x64_sys_read+0x72/0xc0 [ 561.670736] x64_sys_call+0x1b12/0x25f0 [ 561.670738] do_syscall_64+0x87/0x150 [ 561.670741] entry_SYSCALL_64_after_hwframe+0x76/0x7e [ 561.670744] other info that might help us debug this: [ 561.670745] Chain exists of: &hdev->lock --> sk_lock-AF_BLUETOOTH-BTPROTO_ISO --> sk_lock-AF_BLUETOOTH [ 561.670751] Possible unsafe locking scenario: [ 561.670753] CPU0 CPU1 [ 561.670754] ---- ---- [ 561.670756] lock(sk_lock-AF_BLUETOOTH); [ 561.670758] lock(sk_lock AF_BLUETOOTH-BTPROTO_ISO); [ 561.670761] lock(sk_lock-AF_BLUETOOTH); [ 561.670764] lock(&hdev->lock); [ 561.670767] *** DEADLOCK ***

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix potential deadlock with newly created symlinks Syzbot reported that page_symlink(), called by nilfs_symlink(), triggers memory reclamation involving the filesystem layer, which can result in circular lock dependencies among the reader/writer semaphore nilfs->ns_segctor_sem, s_writers percpu_rwsem (intwrite) and the fs_reclaim pseudo lock. This is because after commit 21fc61c73c39 ("don't put symlink bodies in pagecache into highmem"), the gfp flags of the page cache for symbolic links are overwritten to GFP_KERNEL via inode_nohighmem(). This is not a problem for symlinks read from the backing device, because the __GFP_FS flag is dropped after inode_nohighmem() is called. However, when a new symlink is created with nilfs_symlink(), the gfp flags remain overwritten to GFP_KERNEL. Then, memory allocation called from page_symlink() etc. triggers memory reclamation including the FS layer, which may call nilfs_evict_inode() or nilfs_dirty_inode(). And these can cause a deadlock if they are called while nilfs->ns_segctor_sem is held: Fix this issue by dropping the __GFP_FS flag from the page cache GFP flags of newly created symlinks in the same way that nilfs_new_inode() and __nilfs_read_inode() do, as a workaround until we adopt nofs allocation scope consistently or improve the locking constraints.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: remove unreasonable unlock in ocfs2_read_blocks Patch series "Misc fixes for ocfs2_read_blocks", v5. This series contains 2 fixes for ocfs2_read_blocks(). The first patch fix the issue reported by syzbot, which detects bad unlock balance in ocfs2_read_blocks(). The second patch fixes an issue reported by Heming Zhao when reviewing above fix. This patch (of 2): There was a lock release before exiting, so remove the unreasonable unlock.

In the Linux kernel, the following vulnerability has been resolved: KVM: Use dedicated mutex to protect kvm_usage_count to avoid deadlock Use a dedicated mutex to guard kvm_usage_count to fix a potential deadlock on x86 due to a chain of locks and SRCU synchronizations. Translating the below lockdep splat, CPU1 #6 will wait on CPU0 #1, CPU0 #8 will wait on CPU2 #3, and CPU2 #7 will wait on CPU1 #4 (if there's a writer, due to the fairness of r/w semaphores). CPU0 CPU1 CPU2 1 lock(&kvm->slots_lock); 2 lock(&vcpu->mutex); 3 lock(&kvm->srcu); 4 lock(cpu_hotplug_lock); 5 lock(kvm_lock); 6 lock(&kvm->slots_lock); 7 lock(cpu_hotplug_lock); 8 sync(&kvm->srcu); Note, there are likely more potential deadlocks in KVM x86, e.g. the same pattern of taking cpu_hotplug_lock outside of kvm_lock likely exists with __kvmclock_cpufreq_notifier(): cpuhp_cpufreq_online() | -> cpufreq_online() | -> cpufreq_gov_performance_limits() | -> __cpufreq_driver_target() | -> __target_index() | -> cpufreq_freq_transition_begin() | -> cpufreq_notify_transition() | -> ... __kvmclock_cpufreq_notifier() But, actually triggering such deadlocks is beyond rare due to the combination of dependencies and timings involved. E.g. the cpufreq notifier is only used on older CPUs without a constant TSC, mucking with the NX hugepage mitigation while VMs are running is very uncommon, and doing so while also onlining/offlining a CPU (necessary to generate contention on cpu_hotplug_lock) would be even more unusual. The most robust solution to the general cpu_hotplug_lock issue is likely to switch vm_list to be an RCU-protected list, e.g. so that x86's cpufreq notifier doesn't to take kvm_lock. For now, settle for fixing the most blatant deadlock, as switching to an RCU-protected list is a much more involved change, but add a comment in locking.rst to call out that care needs to be taken when walking holding kvm_lock and walking vm_list. ====================================================== WARNING: possible circular locking dependency detected 6.10.0-smp--c257535a0c9d-pip #330 Tainted: G S O ------------------------------------------------------ tee/35048 is trying to acquire lock: ff6a80eced71e0a8 (&kvm->slots_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x179/0x1e0 [kvm] but task is already holding lock: ffffffffc07abb08 (kvm_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x14a/0x1e0 [kvm] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (kvm_lock){+.+.}-{3:3}: __mutex_lock+0x6a/0xb40 mutex_lock_nested+0x1f/0x30 kvm_dev_ioctl+0x4fb/0xe50 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #2 (cpu_hotplug_lock){++++}-{0:0}: cpus_read_lock+0x2e/0xb0 static_key_slow_inc+0x16/0x30 kvm_lapic_set_base+0x6a/0x1c0 [kvm] kvm_set_apic_base+0x8f/0xe0 [kvm] kvm_set_msr_common+0x9ae/0xf80 [kvm] vmx_set_msr+0xa54/0xbe0 [kvm_intel] __kvm_set_msr+0xb6/0x1a0 [kvm] kvm_arch_vcpu_ioctl+0xeca/0x10c0 [kvm] kvm_vcpu_ioctl+0x485/0x5b0 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #1 (&kvm->srcu){.+.+}-{0:0}: __synchronize_srcu+0x44/0x1a0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: media: uvcvideo: Fix deadlock during uvc_probe If uvc_probe() fails, it can end up calling uvc_status_unregister() before uvc_status_init() is called. Fix this by checking if dev->status is NULL or not in uvc_status_unregister().

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix deadlock during RTC update There is a deadlock when runtime suspend waits for the flush of RTC work, and the RTC work calls ufshcd_rpm_get_sync() to wait for runtime resume. Here is deadlock backtrace: kworker/0:1 D 4892.876354 10 10971 4859 0x4208060 0x8 10 0 120 670730152367 ptr f0ffff80c2e40000 0 1 0x00000001 0x000000ff 0x000000ff 0x000000ff <ffffffee5e71ddb0> __switch_to+0x1a8/0x2d4 <ffffffee5e71e604> __schedule+0x684/0xa98 <ffffffee5e71ea60> schedule+0x48/0xc8 <ffffffee5e725f78> schedule_timeout+0x48/0x170 <ffffffee5e71fb74> do_wait_for_common+0x108/0x1b0 <ffffffee5e71efe0> wait_for_completion+0x44/0x60 <ffffffee5d6de968> __flush_work+0x39c/0x424 <ffffffee5d6decc0> __cancel_work_sync+0xd8/0x208 <ffffffee5d6dee2c> cancel_delayed_work_sync+0x14/0x28 <ffffffee5e2551b8> __ufshcd_wl_suspend+0x19c/0x480 <ffffffee5e255fb8> ufshcd_wl_runtime_suspend+0x3c/0x1d4 <ffffffee5dffd80c> scsi_runtime_suspend+0x78/0xc8 <ffffffee5df93580> __rpm_callback+0x94/0x3e0 <ffffffee5df90b0c> rpm_suspend+0x2d4/0x65c <ffffffee5df91448> __pm_runtime_suspend+0x80/0x114 <ffffffee5dffd95c> scsi_runtime_idle+0x38/0x6c <ffffffee5df912f4> rpm_idle+0x264/0x338 <ffffffee5df90f14> __pm_runtime_idle+0x80/0x110 <ffffffee5e24ce44> ufshcd_rtc_work+0x128/0x1e4 <ffffffee5d6e3a40> process_one_work+0x26c/0x650 <ffffffee5d6e65c8> worker_thread+0x260/0x3d8 <ffffffee5d6edec8> kthread+0x110/0x134 <ffffffee5d616b18> ret_from_fork+0x10/0x20 Skip updating RTC if RPM state is not RPM_ACTIVE.

In the Linux kernel, the following vulnerability has been resolved: usb: musb: Fix hardware lockup on first Rx endpoint request There is a possibility that a request's callback could be invoked from usb_ep_queue() (call trace below, supplemented with missing calls): req->complete from usb_gadget_giveback_request (drivers/usb/gadget/udc/core.c:999) usb_gadget_giveback_request from musb_g_giveback (drivers/usb/musb/musb_gadget.c:147) musb_g_giveback from rxstate (drivers/usb/musb/musb_gadget.c:784) rxstate from musb_ep_restart (drivers/usb/musb/musb_gadget.c:1169) musb_ep_restart from musb_ep_restart_resume_work (drivers/usb/musb/musb_gadget.c:1176) musb_ep_restart_resume_work from musb_queue_resume_work (drivers/usb/musb/musb_core.c:2279) musb_queue_resume_work from musb_gadget_queue (drivers/usb/musb/musb_gadget.c:1241) musb_gadget_queue from usb_ep_queue (drivers/usb/gadget/udc/core.c:300) According to the docstring of usb_ep_queue(), this should not happen: "Note that @req's ->complete() callback must never be called from within usb_ep_queue() as that can create deadlock situations." In fact, a hardware lockup might occur in the following sequence: 1. The gadget is initialized using musb_gadget_enable(). 2. Meanwhile, a packet arrives, and the RXPKTRDY flag is set, raising an interrupt. 3. If IRQs are enabled, the interrupt is handled, but musb_g_rx() finds an empty queue (next_request() returns NULL). The interrupt flag has already been cleared by the glue layer handler, but the RXPKTRDY flag remains set. 4. The first request is enqueued using usb_ep_queue(), leading to the call of req->complete(), as shown in the call trace above. 5. If the callback enables IRQs and another packet is waiting, step (3) repeats. The request queue is empty because usb_g_giveback() removes the request before invoking the callback. 6. The endpoint remains locked up, as the interrupt triggered by hardware setting the RXPKTRDY flag has been handled, but the flag itself remains set. For this scenario to occur, it is only necessary for IRQs to be enabled at some point during the complete callback. This happens with the USB Ethernet gadget, whose rx_complete() callback calls netif_rx(). If called in the task context, netif_rx() disables the bottom halves (BHs). When the BHs are re-enabled, IRQs are also enabled to allow soft IRQs to be processed. The gadget itself is initialized at module load (or at boot if built-in), but the first request is enqueued when the network interface is brought up, triggering rx_complete() in the task context via ioctl(). If a packet arrives while the interface is down, it can prevent the interface from receiving any further packets from the USB host. The situation is quite complicated with many parties involved. This particular issue can be resolved in several possible ways: 1. Ensure that callbacks never enable IRQs. This would be difficult to enforce, as discovering how netif_rx() interacts with interrupts was already quite challenging and u_ether is not the only function driver. Similar "bugs" could be hidden in other drivers as well. 2. Disable MUSB interrupts in musb_g_giveback() before calling the callback and re-enable them afterwars (by calling musb_{dis,en}able_interrupts(), for example). This would ensure that MUSB interrupts are not handled during the callback, even if IRQs are enabled. In fact, it would allow IRQs to be enabled when releasing the lock. However, this feels like an inelegant hack. 3. Modify the interrupt handler to clear the RXPKTRDY flag if the request queue is empty. While this approach also feels like a hack, it wastes CPU time by attempting to handle incoming packets when the software is not ready to process them. 4. Flush the Rx FIFO instead of calling rxstate() in musb_ep_restart(). This ensures that the hardware can receive packets when there is at least one request in the queue. Once I ---truncated---

In the Linux kernel, the following vulnerability has been resolved: f2fs: fix to avoid potential deadlock in f2fs_record_stop_reason() syzbot reports deadlock issue of f2fs as below: ====================================================== WARNING: possible circular locking dependency detected 6.12.0-rc3-syzkaller-00087-gc964ced77262 #0 Not tainted ------------------------------------------------------ kswapd0/79 is trying to acquire lock: ffff888011824088 (&sbi->sb_lock){++++}-{3:3}, at: f2fs_down_write fs/f2fs/f2fs.h:2199 [inline] ffff888011824088 (&sbi->sb_lock){++++}-{3:3}, at: f2fs_record_stop_reason+0x52/0x1d0 fs/f2fs/super.c:4068 but task is already holding lock: ffff88804bd92610 (sb_internal#2){.+.+}-{0:0}, at: f2fs_evict_inode+0x662/0x15c0 fs/f2fs/inode.c:842 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (sb_internal#2){.+.+}-{0:0}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5825 percpu_down_read include/linux/percpu-rwsem.h:51 [inline] __sb_start_write include/linux/fs.h:1716 [inline] sb_start_intwrite+0x4d/0x1c0 include/linux/fs.h:1899 f2fs_evict_inode+0x662/0x15c0 fs/f2fs/inode.c:842 evict+0x4e8/0x9b0 fs/inode.c:725 f2fs_evict_inode+0x1a4/0x15c0 fs/f2fs/inode.c:807 evict+0x4e8/0x9b0 fs/inode.c:725 dispose_list fs/inode.c:774 [inline] prune_icache_sb+0x239/0x2f0 fs/inode.c:963 super_cache_scan+0x38c/0x4b0 fs/super.c:223 do_shrink_slab+0x701/0x1160 mm/shrinker.c:435 shrink_slab+0x1093/0x14d0 mm/shrinker.c:662 shrink_one+0x43b/0x850 mm/vmscan.c:4818 shrink_many mm/vmscan.c:4879 [inline] lru_gen_shrink_node mm/vmscan.c:4957 [inline] shrink_node+0x3799/0x3de0 mm/vmscan.c:5937 kswapd_shrink_node mm/vmscan.c:6765 [inline] balance_pgdat mm/vmscan.c:6957 [inline] kswapd+0x1ca3/0x3700 mm/vmscan.c:7226 kthread+0x2f0/0x390 kernel/kthread.c:389 ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 -> #1 (fs_reclaim){+.+.}-{0:0}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5825 __fs_reclaim_acquire mm/page_alloc.c:3834 [inline] fs_reclaim_acquire+0x88/0x130 mm/page_alloc.c:3848 might_alloc include/linux/sched/mm.h:318 [inline] prepare_alloc_pages+0x147/0x5b0 mm/page_alloc.c:4493 __alloc_pages_noprof+0x16f/0x710 mm/page_alloc.c:4722 alloc_pages_mpol_noprof+0x3e8/0x680 mm/mempolicy.c:2265 alloc_pages_noprof mm/mempolicy.c:2345 [inline] folio_alloc_noprof+0x128/0x180 mm/mempolicy.c:2352 filemap_alloc_folio_noprof+0xdf/0x500 mm/filemap.c:1010 do_read_cache_folio+0x2eb/0x850 mm/filemap.c:3787 read_mapping_folio include/linux/pagemap.h:1011 [inline] f2fs_commit_super+0x3c0/0x7d0 fs/f2fs/super.c:4032 f2fs_record_stop_reason+0x13b/0x1d0 fs/f2fs/super.c:4079 f2fs_handle_critical_error+0x2ac/0x5c0 fs/f2fs/super.c:4174 f2fs_write_inode+0x35f/0x4d0 fs/f2fs/inode.c:785 write_inode fs/fs-writeback.c:1503 [inline] __writeback_single_inode+0x711/0x10d0 fs/fs-writeback.c:1723 writeback_single_inode+0x1f3/0x660 fs/fs-writeback.c:1779 sync_inode_metadata+0xc4/0x120 fs/fs-writeback.c:2849 f2fs_release_file+0xa8/0x100 fs/f2fs/file.c:1941 __fput+0x23f/0x880 fs/file_table.c:431 task_work_run+0x24f/0x310 kernel/task_work.c:228 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] exit_to_user_mode_loop kernel/entry/common.c:114 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:328 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x168/0x370 kernel/entry/common.c:218 do_syscall_64+0x100/0x230 arch/x86/entry/common.c:89 entry_SYSCALL_64_after_hwframe+0x77/0x7f ---truncated---

In the Linux kernel, the following vulnerability has been resolved: mm/thp: fix deferred split unqueue naming and locking Recent changes are putting more pressure on THP deferred split queues: under load revealing long-standing races, causing list_del corruptions, "Bad page state"s and worse (I keep BUGs in both of those, so usually don't get to see how badly they end up without). The relevant recent changes being 6.8's mTHP, 6.10's mTHP swapout, and 6.12's mTHP swapin, improved swap allocation, and underused THP splitting. Before fixing locking: rename misleading folio_undo_large_rmappable(), which does not undo large_rmappable, to folio_unqueue_deferred_split(), which is what it does. But that and its out-of-line __callee are mm internals of very limited usability: add comment and WARN_ON_ONCEs to check usage; and return a bool to say if a deferred split was unqueued, which can then be used in WARN_ON_ONCEs around safety checks (sparing callers the arcane conditionals in __folio_unqueue_deferred_split()). Just omit the folio_unqueue_deferred_split() from free_unref_folios(), all of whose callers now call it beforehand (and if any forget then bad_page() will tell) - except for its caller put_pages_list(), which itself no longer has any callers (and will be deleted separately). Swapout: mem_cgroup_swapout() has been resetting folio->memcg_data 0 without checking and unqueueing a THP folio from deferred split list; which is unfortunate, since the split_queue_lock depends on the memcg (when memcg is enabled); so swapout has been unqueueing such THPs later, when freeing the folio, using the pgdat's lock instead: potentially corrupting the memcg's list. __remove_mapping() has frozen refcount to 0 here, so no problem with calling folio_unqueue_deferred_split() before resetting memcg_data. That goes back to 5.4 commit 87eaceb3faa5 ("mm: thp: make deferred split shrinker memcg aware"): which included a check on swapcache before adding to deferred queue, but no check on deferred queue before adding THP to swapcache. That worked fine with the usual sequence of events in reclaim (though there were a couple of rare ways in which a THP on deferred queue could have been swapped out), but 6.12 commit dafff3f4c850 ("mm: split underused THPs") avoids splitting underused THPs in reclaim, which makes swapcache THPs on deferred queue commonplace. Keep the check on swapcache before adding to deferred queue? Yes: it is no longer essential, but preserves the existing behaviour, and is likely to be a worthwhile optimization (vmstat showed much more traffic on the queue under swapping load if the check was removed); update its comment. Memcg-v1 move (deprecated): mem_cgroup_move_account() has been changing folio->memcg_data without checking and unqueueing a THP folio from the deferred list, sometimes corrupting "from" memcg's list, like swapout. Refcount is non-zero here, so folio_unqueue_deferred_split() can only be used in a WARN_ON_ONCE to validate the fix, which must be done earlier: mem_cgroup_move_charge_pte_range() first try to split the THP (splitting of course unqueues), or skip it if that fails. Not ideal, but moving charge has been requested, and khugepaged should repair the THP later: nobody wants new custom unqueueing code just for this deprecated case. The 87eaceb3faa5 commit did have the code to move from one deferred list to another (but was not conscious of its unsafety while refcount non-0); but that was removed by 5.6 commit fac0516b5534 ("mm: thp: don't need care deferred split queue in memcg charge move path"), which argued that the existence of a PMD mapping guarantees that the THP cannot be on a deferred list. As above, false in rare cases, and now commonly false. Backport to 6.11 should be straightforward. Earlier backports must take care that other _deferred_list fixes and dependencies are included. There is not a strong case for backports, but they can fix cornercases.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Fix another deadlock during RTC update If ufshcd_rtc_work calls ufshcd_rpm_put_sync() and the pm's usage_count is 0, we will enter the runtime suspend callback. However, the runtime suspend callback will wait to flush ufshcd_rtc_work, causing a deadlock. Replace ufshcd_rpm_put_sync() with ufshcd_rpm_put() to avoid the deadlock.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Fix sleeping in atomic context for PREEMPT_RT Commit bab1c299f3945ffe79 ("LoongArch: Fix sleeping in atomic context in setup_tlb_handler()") changes the gfp flag from GFP_KERNEL to GFP_ATOMIC for alloc_pages_node(). However, for PREEMPT_RT kernels we can still get a "sleeping in atomic context" error: [ 0.372259] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 [ 0.372266] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/1 [ 0.372268] preempt_count: 1, expected: 0 [ 0.372270] RCU nest depth: 1, expected: 1 [ 0.372272] 3 locks held by swapper/1/0: [ 0.372274] #0: 900000000c9f5e60 (&pcp->lock){+.+.}-{3:3}, at: get_page_from_freelist+0x524/0x1c60 [ 0.372294] #1: 90000000087013b8 (rcu_read_lock){....}-{1:3}, at: rt_spin_trylock+0x50/0x140 [ 0.372305] #2: 900000047fffd388 (&zone->lock){+.+.}-{3:3}, at: __rmqueue_pcplist+0x30c/0xea0 [ 0.372314] irq event stamp: 0 [ 0.372316] hardirqs last enabled at (0): [<0000000000000000>] 0x0 [ 0.372322] hardirqs last disabled at (0): [<9000000005947320>] copy_process+0x9c0/0x26e0 [ 0.372329] softirqs last enabled at (0): [<9000000005947320>] copy_process+0x9c0/0x26e0 [ 0.372335] softirqs last disabled at (0): [<0000000000000000>] 0x0 [ 0.372341] CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Not tainted 6.12.0-rc7+ #1891 [ 0.372346] Hardware name: Loongson Loongson-3A5000-7A1000-1w-CRB/Loongson-LS3A5000-7A1000-1w-CRB, BIOS vUDK2018-LoongArch-V2.0.0-prebeta9 10/21/2022 [ 0.372349] Stack : 0000000000000089 9000000005a0db9c 90000000071519c8 9000000100388000 [ 0.372486] 900000010038b890 0000000000000000 900000010038b898 9000000007e53788 [ 0.372492] 900000000815bcc8 900000000815bcc0 900000010038b700 0000000000000001 [ 0.372498] 0000000000000001 4b031894b9d6b725 00000000055ec000 9000000100338fc0 [ 0.372503] 00000000000000c4 0000000000000001 000000000000002d 0000000000000003 [ 0.372509] 0000000000000030 0000000000000003 00000000055ec000 0000000000000003 [ 0.372515] 900000000806d000 9000000007e53788 00000000000000b0 0000000000000004 [ 0.372521] 0000000000000000 0000000000000000 900000000c9f5f10 0000000000000000 [ 0.372526] 90000000076f12d8 9000000007e53788 9000000005924778 0000000000000000 [ 0.372532] 00000000000000b0 0000000000000004 0000000000000000 0000000000070000 [ 0.372537] ... [ 0.372540] Call Trace: [ 0.372542] [<9000000005924778>] show_stack+0x38/0x180 [ 0.372548] [<90000000071519c4>] dump_stack_lvl+0x94/0xe4 [ 0.372555] [<900000000599b880>] __might_resched+0x1a0/0x260 [ 0.372561] [<90000000071675cc>] rt_spin_lock+0x4c/0x140 [ 0.372565] [<9000000005cbb768>] __rmqueue_pcplist+0x308/0xea0 [ 0.372570] [<9000000005cbed84>] get_page_from_freelist+0x564/0x1c60 [ 0.372575] [<9000000005cc0d98>] __alloc_pages_noprof+0x218/0x1820 [ 0.372580] [<900000000593b36c>] tlb_init+0x1ac/0x298 [ 0.372585] [<9000000005924b74>] per_cpu_trap_init+0x114/0x140 [ 0.372589] [<9000000005921964>] cpu_probe+0x4e4/0xa60 [ 0.372592] [<9000000005934874>] start_secondary+0x34/0xc0 [ 0.372599] [<900000000715615c>] smpboot_entry+0x64/0x6c This is because in PREEMPT_RT kernels normal spinlocks are replaced by rt spinlocks and rt_spin_lock() will cause sleeping. Fix it by disabling NUMA optimization completely for PREEMPT_RT kernels.

In the Linux kernel, the following vulnerability has been resolved: media: mediatek: vcodec: prevent kernel crash when rmmod mtk-vcodec-dec.ko If the driver support subdev mode, the parameter "dev->pm.dev" will be NULL in mtk_vcodec_dec_remove. Kernel will crash when try to rmmod mtk-vcodec-dec.ko. [ 4380.702726] pc : do_raw_spin_trylock+0x4/0x80 [ 4380.707075] lr : _raw_spin_lock_irq+0x90/0x14c [ 4380.711509] sp : ffff80000819bc10 [ 4380.714811] x29: ffff80000819bc10 x28: ffff3600c03e4000 x27: 0000000000000000 [ 4380.721934] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000 [ 4380.729057] x23: ffff3600c0f34930 x22: ffffd5e923549000 x21: 0000000000000220 [ 4380.736179] x20: 0000000000000208 x19: ffffd5e9213e8ebc x18: 0000000000000020 [ 4380.743298] x17: 0000002000000000 x16: ffffd5e9213e8e90 x15: 696c346f65646976 [ 4380.750420] x14: 0000000000000000 x13: 0000000000000001 x12: 0000000000000040 [ 4380.757542] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 [ 4380.764664] x8 : 0000000000000000 x7 : ffff3600c7273ae8 x6 : ffffd5e9213e8ebc [ 4380.771786] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000 [ 4380.778908] x2 : 0000000000000000 x1 : ffff3600c03e4000 x0 : 0000000000000208 [ 4380.786031] Call trace: [ 4380.788465] do_raw_spin_trylock+0x4/0x80 [ 4380.792462] __pm_runtime_disable+0x2c/0x1b0 [ 4380.796723] mtk_vcodec_dec_remove+0x5c/0xa0 [mtk_vcodec_dec] [ 4380.802466] platform_remove+0x2c/0x60 [ 4380.806204] __device_release_driver+0x194/0x250 [ 4380.810810] driver_detach+0xc8/0x15c [ 4380.814462] bus_remove_driver+0x5c/0xb0 [ 4380.818375] driver_unregister+0x34/0x64 [ 4380.822288] platform_driver_unregister+0x18/0x24 [ 4380.826979] mtk_vcodec_dec_driver_exit+0x1c/0x888 [mtk_vcodec_dec] [ 4380.833240] __arm64_sys_delete_module+0x190/0x224 [ 4380.838020] invoke_syscall+0x48/0x114 [ 4380.841760] el0_svc_common.constprop.0+0x60/0x11c [ 4380.846540] do_el0_svc+0x28/0x90 [ 4380.849844] el0_svc+0x4c/0x100 [ 4380.852975] el0t_64_sync_handler+0xec/0xf0 [ 4380.857148] el0t_64_sync+0x190/0x194 [ 4380.860801] Code: 94431515 17ffffca d503201f d503245f (b9400004)

In the Linux kernel, the following vulnerability has been resolved: ceph: fix possible deadlock when holding Fwb to get inline_data 1, mount with wsync. 2, create a file with O_RDWR, and the request was sent to mds.0: ceph_atomic_open()--> ceph_mdsc_do_request(openc) finish_open(file, dentry, ceph_open)--> ceph_open()--> ceph_init_file()--> ceph_init_file_info()--> ceph_uninline_data()--> { ... if (inline_version == 1 || /* initial version, no data */ inline_version == CEPH_INLINE_NONE) goto out_unlock; ... } The inline_version will be 1, which is the initial version for the new create file. And here the ci->i_inline_version will keep with 1, it's buggy. 3, buffer write to the file immediately: ceph_write_iter()--> ceph_get_caps(file, need=Fw, want=Fb, ...); generic_perform_write()--> a_ops->write_begin()--> ceph_write_begin()--> netfs_write_begin()--> netfs_begin_read()--> netfs_rreq_submit_slice()--> netfs_read_from_server()--> rreq->netfs_ops->issue_read()--> ceph_netfs_issue_read()--> { ... if (ci->i_inline_version != CEPH_INLINE_NONE && ceph_netfs_issue_op_inline(subreq)) return; ... } ceph_put_cap_refs(ci, Fwb); The ceph_netfs_issue_op_inline() will send a getattr(Fsr) request to mds.1. 4, then the mds.1 will request the rd lock for CInode::filelock from the auth mds.0, the mds.0 will do the CInode::filelock state transation from excl --> sync, but it need to revoke the Fxwb caps back from the clients. While the kernel client has aleady held the Fwb caps and waiting for the getattr(Fsr). It's deadlock! URL: https://tracker.ceph.com/issues/55377

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix hang during unmount when block group reclaim task is running When we start an unmount, at close_ctree(), if we have the reclaim task running and in the middle of a data block group relocation, we can trigger a deadlock when stopping an async reclaim task, producing a trace like the following: [629724.498185] task:kworker/u16:7 state:D stack: 0 pid:681170 ppid: 2 flags:0x00004000 [629724.499760] Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs] [629724.501267] Call Trace: [629724.501759] <TASK> [629724.502174] __schedule+0x3cb/0xed0 [629724.502842] schedule+0x4e/0xb0 [629724.503447] btrfs_wait_on_delayed_iputs+0x7c/0xc0 [btrfs] [629724.504534] ? prepare_to_wait_exclusive+0xc0/0xc0 [629724.505442] flush_space+0x423/0x630 [btrfs] [629724.506296] ? rcu_read_unlock_trace_special+0x20/0x50 [629724.507259] ? lock_release+0x220/0x4a0 [629724.507932] ? btrfs_get_alloc_profile+0xb3/0x290 [btrfs] [629724.508940] ? do_raw_spin_unlock+0x4b/0xa0 [629724.509688] btrfs_async_reclaim_metadata_space+0x139/0x320 [btrfs] [629724.510922] process_one_work+0x252/0x5a0 [629724.511694] ? process_one_work+0x5a0/0x5a0 [629724.512508] worker_thread+0x52/0x3b0 [629724.513220] ? process_one_work+0x5a0/0x5a0 [629724.514021] kthread+0xf2/0x120 [629724.514627] ? kthread_complete_and_exit+0x20/0x20 [629724.515526] ret_from_fork+0x22/0x30 [629724.516236] </TASK> [629724.516694] task:umount state:D stack: 0 pid:719055 ppid:695412 flags:0x00004000 [629724.518269] Call Trace: [629724.518746] <TASK> [629724.519160] __schedule+0x3cb/0xed0 [629724.519835] schedule+0x4e/0xb0 [629724.520467] schedule_timeout+0xed/0x130 [629724.521221] ? lock_release+0x220/0x4a0 [629724.521946] ? lock_acquired+0x19c/0x420 [629724.522662] ? trace_hardirqs_on+0x1b/0xe0 [629724.523411] __wait_for_common+0xaf/0x1f0 [629724.524189] ? usleep_range_state+0xb0/0xb0 [629724.524997] __flush_work+0x26d/0x530 [629724.525698] ? flush_workqueue_prep_pwqs+0x140/0x140 [629724.526580] ? lock_acquire+0x1a0/0x310 [629724.527324] __cancel_work_timer+0x137/0x1c0 [629724.528190] close_ctree+0xfd/0x531 [btrfs] [629724.529000] ? evict_inodes+0x166/0x1c0 [629724.529510] generic_shutdown_super+0x74/0x120 [629724.530103] kill_anon_super+0x14/0x30 [629724.530611] btrfs_kill_super+0x12/0x20 [btrfs] [629724.531246] deactivate_locked_super+0x31/0xa0 [629724.531817] cleanup_mnt+0x147/0x1c0 [629724.532319] task_work_run+0x5c/0xa0 [629724.532984] exit_to_user_mode_prepare+0x1a6/0x1b0 [629724.533598] syscall_exit_to_user_mode+0x16/0x40 [629724.534200] do_syscall_64+0x48/0x90 [629724.534667] entry_SYSCALL_64_after_hwframe+0x44/0xae [629724.535318] RIP: 0033:0x7fa2b90437a7 [629724.535804] RSP: 002b:00007ffe0b7e4458 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6 [629724.536912] RAX: 0000000000000000 RBX: 00007fa2b9182264 RCX: 00007fa2b90437a7 [629724.538156] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000555d6cf20dd0 [629724.539053] RBP: 0000555d6cf20ba0 R08: 0000000000000000 R09: 00007ffe0b7e3200 [629724.539956] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 [629724.540883] R13: 0000555d6cf20dd0 R14: 0000555d6cf20cb0 R15: 0000000000000000 [629724.541796] </TASK> This happens because: 1) Before entering close_ctree() we have the async block group reclaim task running and relocating a data block group; 2) There's an async metadata (or data) space reclaim task running; 3) We enter close_ctree() and park the cleaner kthread; 4) The async space reclaim task is at flush_space() and runs all the existing delayed iputs; 5) Before the async space reclaim task calls btrfs_wait_on_delayed_iputs(), the block group reclaim task which is doing the data block group relocation, creates a delayed iput at replace_file_extents() (called when COWing leaves that have file extent items pointing to relocated data exten ---truncated---

In the Linux kernel, the following vulnerability has been resolved: USB: gadget: Fix obscure lockdep violation for udc_mutex A recent commit expanding the scope of the udc_lock mutex in the gadget core managed to cause an obscure and slightly bizarre lockdep violation. In abbreviated form: ====================================================== WARNING: possible circular locking dependency detected 5.19.0-rc7+ #12510 Not tainted ------------------------------------------------------ udevadm/312 is trying to acquire lock: ffff80000aae1058 (udc_lock){+.+.}-{3:3}, at: usb_udc_uevent+0x54/0xe0 but task is already holding lock: ffff000002277548 (kn->active#4){++++}-{0:0}, at: kernfs_seq_start+0x34/0xe0 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (kn->active#4){++++}-{0:0}:        lock_acquire+0x68/0x84        __kernfs_remove+0x268/0x380        kernfs_remove_by_name_ns+0x58/0xac        sysfs_remove_file_ns+0x18/0x24        device_del+0x15c/0x440 -> #2 (device_links_lock){+.+.}-{3:3}:        lock_acquire+0x68/0x84        __mutex_lock+0x9c/0x430        mutex_lock_nested+0x38/0x64        device_link_remove+0x3c/0xa0        _regulator_put.part.0+0x168/0x190        regulator_put+0x3c/0x54        devm_regulator_release+0x14/0x20 -> #1 (regulator_list_mutex){+.+.}-{3:3}:        lock_acquire+0x68/0x84        __mutex_lock+0x9c/0x430        mutex_lock_nested+0x38/0x64        regulator_lock_dependent+0x54/0x284        regulator_enable+0x34/0x80        phy_power_on+0x24/0x130        __dwc2_lowlevel_hw_enable+0x100/0x130        dwc2_lowlevel_hw_enable+0x18/0x40        dwc2_hsotg_udc_start+0x6c/0x2f0        gadget_bind_driver+0x124/0x1f4 -> #0 (udc_lock){+.+.}-{3:3}:        __lock_acquire+0x1298/0x20cc        lock_acquire.part.0+0xe0/0x230        lock_acquire+0x68/0x84        __mutex_lock+0x9c/0x430        mutex_lock_nested+0x38/0x64        usb_udc_uevent+0x54/0xe0 Evidently this was caused by the scope of udc_mutex being too large. The mutex is only meant to protect udc->driver along with a few other things. As far as I can tell, there's no reason for the mutex to be held while the gadget core calls a gadget driver's ->bind or ->unbind routine, or while a UDC is being started or stopped. (This accounts for link #1 in the chain above, where the mutex is held while the dwc2_hsotg_udc is started as part of driver probing.) Gadget drivers' ->disconnect callbacks are problematic. Even though usb_gadget_disconnect() will now acquire the udc_mutex, there's a window in usb_gadget_bind_driver() between the times when the mutex is released and the ->bind callback is invoked. If a disconnect occurred during that window, we could call the driver's ->disconnect routine before its ->bind routine. To prevent this from happening, it will be necessary to prevent a UDC from connecting while it has no gadget driver. This should be done already but it doesn't seem to be; currently usb_gadget_connect() has no check for this. Such a check will have to be added later. Some degree of mutual exclusion is required in soft_connect_store(), which can dereference udc->driver at arbitrary times since it is a sysfs callback. The solution here is to acquire the gadget's device lock rather than the udc_mutex. Since the driver core guarantees that the device lock is always held during driver binding and unbinding, this will make the accesses in soft_connect_store() mutually exclusive with any changes to udc->driver. Lastly, it turns out there is one place which should hold the udc_mutex but currently does not: The function_show() routine needs protection while it dereferences udc->driver. The missing lock and unlock calls are added.

In the Linux kernel, the following vulnerability has been resolved: driver core: fix potential deadlock in __driver_attach In __driver_attach function, There are also AA deadlock problem, like the commit b232b02bf3c2 ("driver core: fix deadlock in __device_attach"). stack like commit b232b02bf3c2 ("driver core: fix deadlock in __device_attach"). list below: In __driver_attach function, The lock holding logic is as follows: ... __driver_attach if (driver_allows_async_probing(drv)) device_lock(dev) // get lock dev async_schedule_dev(__driver_attach_async_helper, dev); // func async_schedule_node async_schedule_node_domain(func) entry = kzalloc(sizeof(struct async_entry), GFP_ATOMIC); /* when fail or work limit, sync to execute func, but __driver_attach_async_helper will get lock dev as will, which will lead to A-A deadlock. */ if (!entry || atomic_read(&entry_count) > MAX_WORK) { func; else queue_work_node(node, system_unbound_wq, &entry->work) device_unlock(dev) As above show, when it is allowed to do async probes, because of out of memory or work limit, async work is not be allowed, to do sync execute instead. it will lead to A-A deadlock because of __driver_attach_async_helper getting lock dev. Reproduce: and it can be reproduce by make the condition (if (!entry || atomic_read(&entry_count) > MAX_WORK)) untenable, like below: [ 370.785650] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 370.787154] task:swapper/0 state:D stack: 0 pid: 1 ppid: 0 flags:0x00004000 [ 370.788865] Call Trace: [ 370.789374] <TASK> [ 370.789841] __schedule+0x482/0x1050 [ 370.790613] schedule+0x92/0x1a0 [ 370.791290] schedule_preempt_disabled+0x2c/0x50 [ 370.792256] __mutex_lock.isra.0+0x757/0xec0 [ 370.793158] __mutex_lock_slowpath+0x1f/0x30 [ 370.794079] mutex_lock+0x50/0x60 [ 370.794795] __device_driver_lock+0x2f/0x70 [ 370.795677] ? driver_probe_device+0xd0/0xd0 [ 370.796576] __driver_attach_async_helper+0x1d/0xd0 [ 370.797318] ? driver_probe_device+0xd0/0xd0 [ 370.797957] async_schedule_node_domain+0xa5/0xc0 [ 370.798652] async_schedule_node+0x19/0x30 [ 370.799243] __driver_attach+0x246/0x290 [ 370.799828] ? driver_allows_async_probing+0xa0/0xa0 [ 370.800548] bus_for_each_dev+0x9d/0x130 [ 370.801132] driver_attach+0x22/0x30 [ 370.801666] bus_add_driver+0x290/0x340 [ 370.802246] driver_register+0x88/0x140 [ 370.802817] ? virtio_scsi_init+0x116/0x116 [ 370.803425] scsi_register_driver+0x1a/0x30 [ 370.804057] init_sd+0x184/0x226 [ 370.804533] do_one_initcall+0x71/0x3a0 [ 370.805107] kernel_init_freeable+0x39a/0x43a [ 370.805759] ? rest_init+0x150/0x150 [ 370.806283] kernel_init+0x26/0x230 [ 370.806799] ret_from_fork+0x1f/0x30 To fix the deadlock, move the async_schedule_dev outside device_lock, as we can see, in async_schedule_node_domain, the parameter of queue_work_node is system_unbound_wq, so it can accept concurrent operations. which will also not change the code logic, and will not lead to deadlock.

In the Linux kernel, the following vulnerability has been resolved: mptcp: fix sleep in atomic at close time Matt reported a splat at msk close time: BUG: sleeping function called from invalid context at net/mptcp/protocol.c:2877 in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 155, name: packetdrill preempt_count: 201, expected: 0 RCU nest depth: 0, expected: 0 4 locks held by packetdrill/155: #0: ffff888001536990 (&sb->s_type->i_mutex_key#6){+.+.}-{3:3}, at: __sock_release (net/socket.c:650) #1: ffff88800b498130 (sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_close (net/mptcp/protocol.c:2973) #2: ffff88800b49a130 (sk_lock-AF_INET/1){+.+.}-{0:0}, at: __mptcp_close_ssk (net/mptcp/protocol.c:2363) #3: ffff88800b49a0b0 (slock-AF_INET){+...}-{2:2}, at: __lock_sock_fast (include/net/sock.h:1820) Preemption disabled at: 0x0 CPU: 1 PID: 155 Comm: packetdrill Not tainted 6.1.0-rc5 #365 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Call Trace: <TASK> dump_stack_lvl (lib/dump_stack.c:107 (discriminator 4)) __might_resched.cold (kernel/sched/core.c:9891) __mptcp_destroy_sock (include/linux/kernel.h:110) __mptcp_close (net/mptcp/protocol.c:2959) mptcp_subflow_queue_clean (include/net/sock.h:1777) __mptcp_close_ssk (net/mptcp/protocol.c:2363) mptcp_destroy_common (net/mptcp/protocol.c:3170) mptcp_destroy (include/net/sock.h:1495) __mptcp_destroy_sock (net/mptcp/protocol.c:2886) __mptcp_close (net/mptcp/protocol.c:2959) mptcp_close (net/mptcp/protocol.c:2974) inet_release (net/ipv4/af_inet.c:432) __sock_release (net/socket.c:651) sock_close (net/socket.c:1367) __fput (fs/file_table.c:320) task_work_run (kernel/task_work.c:181 (discriminator 1)) exit_to_user_mode_prepare (include/linux/resume_user_mode.h:49) syscall_exit_to_user_mode (kernel/entry/common.c:130) do_syscall_64 (arch/x86/entry/common.c:87) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) We can't call mptcp_close under the 'fast' socket lock variant, replace it with a sock_lock_nested() as the relevant code is already under the listening msk socket lock protection.

In the Linux kernel, the following vulnerability has been resolved: Revert "libfs: fix infinite directory reads for offset dir" The current directory offset allocator (based on mtree_alloc_cyclic) stores the next offset value to return in octx->next_offset. This mechanism typically returns values that increase monotonically over time. Eventually, though, the newly allocated offset value wraps back to a low number (say, 2) which is smaller than other already- allocated offset values. Yu Kuai <yukuai3@huawei.com> reports that, after commit 64a7ce76fb90 ("libfs: fix infinite directory reads for offset dir"), if a directory's offset allocator wraps, existing entries are no longer visible via readdir/getdents because offset_readdir() stops listing entries once an entry's offset is larger than octx->next_offset. These entries vanish persistently -- they can be looked up, but will never again appear in readdir(3) output. The reason for this is that the commit treats directory offsets as monotonically increasing integer values rather than opaque cookies, and introduces this comparison: if (dentry2offset(dentry) >= last_index) { On 64-bit platforms, the directory offset value upper bound is 2^63 - 1. Directory offsets will monotonically increase for millions of years without wrapping. On 32-bit platforms, however, LONG_MAX is 2^31 - 1. The allocator can wrap after only a few weeks (at worst). Revert commit 64a7ce76fb90 ("libfs: fix infinite directory reads for offset dir") to prepare for a fix that can work properly on 32-bit systems and might apply to recent LTS kernels where shmem employs the simple_offset mechanism.

In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: scm: Cleanup global '__scm' on probe failures If SCM driver fails the probe, it should not leave global '__scm' variable assigned, because external users of this driver will assume the probe finished successfully. For example TZMEM parts ('__scm->mempool') are initialized later in the probe, but users of it (__scm_smc_call()) rely on the '__scm' variable. This fixes theoretical NULL pointer exception, triggered via introducing probe deferral in SCM driver with call trace: qcom_tzmem_alloc+0x70/0x1ac (P) qcom_tzmem_alloc+0x64/0x1ac (L) qcom_scm_assign_mem+0x78/0x194 qcom_rmtfs_mem_probe+0x2d4/0x38c platform_probe+0x68/0xc8

gss_mech_free in net/sunrpc/auth_gss/gss_mech_switch.c in the rpcsec_gss_krb5 implementation in the Linux kernel through 5.6.10 lacks certain domain_release calls, leading to a memory leak. Note: This was disputed with the assertion that the issue does not grant any access not already available. It is a problem that on unloading a specific kernel module some memory is leaked, but loading kernel modules is a privileged operation. A user could also write a kernel module to consume any amount of memory they like and load that replicating the effect of this bug

In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: scm: fix a NULL-pointer dereference Some SCM calls can be invoked with __scm being NULL (the driver may not have been and will not be probed as there's no SCM entry in device-tree). Make sure we don't dereference a NULL pointer.

In the Linux kernel, the following vulnerability has been resolved: riscv: Fix IPIs usage in kfence_protect_page() flush_tlb_kernel_range() may use IPIs to flush the TLBs of all the cores, which triggers the following warning when the irqs are disabled: [ 3.455330] WARNING: CPU: 1 PID: 0 at kernel/smp.c:815 smp_call_function_many_cond+0x452/0x520 [ 3.456647] Modules linked in: [ 3.457218] CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Not tainted 6.12.0-rc7-00010-g91d3de7240b8 #1 [ 3.457416] Hardware name: QEMU QEMU Virtual Machine, BIOS [ 3.457633] epc : smp_call_function_many_cond+0x452/0x520 [ 3.457736] ra : on_each_cpu_cond_mask+0x1e/0x30 [ 3.457786] epc : ffffffff800b669a ra : ffffffff800b67c2 sp : ff2000000000bb50 [ 3.457824] gp : ffffffff815212b8 tp : ff6000008014f080 t0 : 000000000000003f [ 3.457859] t1 : ffffffff815221e0 t2 : 000000000000000f s0 : ff2000000000bc10 [ 3.457920] s1 : 0000000000000040 a0 : ffffffff815221e0 a1 : 0000000000000001 [ 3.457953] a2 : 0000000000010000 a3 : 0000000000000003 a4 : 0000000000000000 [ 3.458006] a5 : 0000000000000000 a6 : ffffffffffffffff a7 : 0000000000000000 [ 3.458042] s2 : ffffffff815223be s3 : 00fffffffffff000 s4 : ff600001ffe38fc0 [ 3.458076] s5 : ff600001ff950d00 s6 : 0000000200000120 s7 : 0000000000000001 [ 3.458109] s8 : 0000000000000001 s9 : ff60000080841ef0 s10: 0000000000000001 [ 3.458141] s11: ffffffff81524812 t3 : 0000000000000001 t4 : ff60000080092bc0 [ 3.458172] t5 : 0000000000000000 t6 : ff200000000236d0 [ 3.458203] status: 0000000200000100 badaddr: ffffffff800b669a cause: 0000000000000003 [ 3.458373] [<ffffffff800b669a>] smp_call_function_many_cond+0x452/0x520 [ 3.458593] [<ffffffff800b67c2>] on_each_cpu_cond_mask+0x1e/0x30 [ 3.458625] [<ffffffff8000e4ca>] __flush_tlb_range+0x118/0x1ca [ 3.458656] [<ffffffff8000e6b2>] flush_tlb_kernel_range+0x1e/0x26 [ 3.458683] [<ffffffff801ea56a>] kfence_protect+0xc0/0xce [ 3.458717] [<ffffffff801e9456>] kfence_guarded_free+0xc6/0x1c0 [ 3.458742] [<ffffffff801e9d6c>] __kfence_free+0x62/0xc6 [ 3.458764] [<ffffffff801c57d8>] kfree+0x106/0x32c [ 3.458786] [<ffffffff80588cf2>] detach_buf_split+0x188/0x1a8 [ 3.458816] [<ffffffff8058708c>] virtqueue_get_buf_ctx+0xb6/0x1f6 [ 3.458839] [<ffffffff805871da>] virtqueue_get_buf+0xe/0x16 [ 3.458880] [<ffffffff80613d6a>] virtblk_done+0x5c/0xe2 [ 3.458908] [<ffffffff8058766e>] vring_interrupt+0x6a/0x74 [ 3.458930] [<ffffffff800747d8>] __handle_irq_event_percpu+0x7c/0xe2 [ 3.458956] [<ffffffff800748f0>] handle_irq_event+0x3c/0x86 [ 3.458978] [<ffffffff800786cc>] handle_simple_irq+0x9e/0xbe [ 3.459004] [<ffffffff80073934>] generic_handle_domain_irq+0x1c/0x2a [ 3.459027] [<ffffffff804bf87c>] imsic_handle_irq+0xba/0x120 [ 3.459056] [<ffffffff80073934>] generic_handle_domain_irq+0x1c/0x2a [ 3.459080] [<ffffffff804bdb76>] riscv_intc_aia_irq+0x24/0x34 [ 3.459103] [<ffffffff809d0452>] handle_riscv_irq+0x2e/0x4c [ 3.459133] [<ffffffff809d923e>] call_on_irq_stack+0x32/0x40 So only flush the local TLB and let the lazy kfence page fault handling deal with the faults which could happen when a core has an old protected pte version cached in its TLB. That leads to potential inaccuracies which can be tolerated when using kfence.

In the Linux kernel, the following vulnerability has been resolved: selinux: ignore unknown extended permissions When evaluating extended permissions, ignore unknown permissions instead of calling BUG(). This commit ensures that future permissions can be added without interfering with older kernels.

In the Linux kernel, the following vulnerability has been resolved: PCI: dwc: ep: Prevent changing BAR size/flags in pci_epc_set_bar() In commit 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address") set_bar() was modified to support dynamically changing the backing physical address of a BAR that was already configured. This means that set_bar() can be called twice, without ever calling clear_bar() (as calling clear_bar() would clear the BAR's PCI address assigned by the host). This can only be done if the new BAR size/flags does not differ from the existing BAR configuration. Add these missing checks. If we allow set_bar() to set e.g. a new BAR size that differs from the existing BAR size, the new address translation range will be smaller than the BAR size already determined by the host, which would mean that a read past the new BAR size would pass the iATU untranslated, which could allow the host to read memory not belonging to the new struct pci_epf_bar. While at it, add comments which clarifies the support for dynamically changing the physical address of a BAR. (Which was also missing.)

In the Linux kernel, the following vulnerability has been resolved: ptp: Ensure info->enable callback is always set The ioctl and sysfs handlers unconditionally call the ->enable callback. Not all drivers implement that callback, leading to NULL dereferences. Example of affected drivers: ptp_s390.c, ptp_vclock.c and ptp_mock.c. Instead use a dummy callback if no better was specified by the driver.

In the Linux kernel, the following vulnerability has been resolved: btrfs: do proper folio cleanup when cow_file_range() failed [BUG] When testing with COW fixup marked as BUG_ON() (this is involved with the new pin_user_pages*() change, which should not result new out-of-band dirty pages), I hit a crash triggered by the BUG_ON() from hitting COW fixup path. This BUG_ON() happens just after a failed btrfs_run_delalloc_range(): BTRFS error (device dm-2): failed to run delalloc range, root 348 ino 405 folio 65536 submit_bitmap 6-15 start 90112 len 106496: -28 ------------[ cut here ]------------ kernel BUG at fs/btrfs/extent_io.c:1444! Internal error: Oops - BUG: 00000000f2000800 [#1] SMP CPU: 0 UID: 0 PID: 434621 Comm: kworker/u24:8 Tainted: G OE 6.12.0-rc7-custom+ #86 Hardware name: QEMU KVM Virtual Machine, BIOS unknown 2/2/2022 Workqueue: events_unbound btrfs_async_reclaim_data_space [btrfs] pc : extent_writepage_io+0x2d4/0x308 [btrfs] lr : extent_writepage_io+0x2d4/0x308 [btrfs] Call trace: extent_writepage_io+0x2d4/0x308 [btrfs] extent_writepage+0x218/0x330 [btrfs] extent_write_cache_pages+0x1d4/0x4b0 [btrfs] btrfs_writepages+0x94/0x150 [btrfs] do_writepages+0x74/0x190 filemap_fdatawrite_wbc+0x88/0xc8 start_delalloc_inodes+0x180/0x3b0 [btrfs] btrfs_start_delalloc_roots+0x174/0x280 [btrfs] shrink_delalloc+0x114/0x280 [btrfs] flush_space+0x250/0x2f8 [btrfs] btrfs_async_reclaim_data_space+0x180/0x228 [btrfs] process_one_work+0x164/0x408 worker_thread+0x25c/0x388 kthread+0x100/0x118 ret_from_fork+0x10/0x20 Code: aa1403e1 9402f3ef aa1403e0 9402f36f (d4210000) ---[ end trace 0000000000000000 ]--- [CAUSE] That failure is mostly from cow_file_range(), where we can hit -ENOSPC. Although the -ENOSPC is already a bug related to our space reservation code, let's just focus on the error handling. For example, we have the following dirty range [0, 64K) of an inode, with 4K sector size and 4K page size: 0 16K 32K 48K 64K |///////////////////////////////////////| |#######################################| Where |///| means page are still dirty, and |###| means the extent io tree has EXTENT_DELALLOC flag. - Enter extent_writepage() for page 0 - Enter btrfs_run_delalloc_range() for range [0, 64K) - Enter cow_file_range() for range [0, 64K) - Function btrfs_reserve_extent() only reserved one 16K extent So we created extent map and ordered extent for range [0, 16K) 0 16K 32K 48K 64K |////////|//////////////////////////////| |<- OE ->|##############################| And range [0, 16K) has its delalloc flag cleared. But since we haven't yet submit any bio, involved 4 pages are still dirty. - Function btrfs_reserve_extent() returns with -ENOSPC Now we have to run error cleanup, which will clear all EXTENT_DELALLOC* flags and clear the dirty flags for the remaining ranges: 0 16K 32K 48K 64K |////////| | | | | Note that range [0, 16K) still has its pages dirty. - Some time later, writeback is triggered again for the range [0, 16K) since the page range still has dirty flags. - btrfs_run_delalloc_range() will do nothing because there is no EXTENT_DELALLOC flag. - extent_writepage_io() finds page 0 has no ordered flag Which falls into the COW fixup path, triggering the BUG_ON(). Unfortunately this error handling bug dates back to the introduction of btrfs. Thankfully with the abuse of COW fixup, at least it won't crash the kernel. [FIX] Instead of immediately unlocking the extent and folios, we keep the extent and folios locked until either erroring out or the whole delalloc range finished. When the whole delalloc range finished without error, we just unlock the whole range with PAGE_SET_ORDERED (and PAGE_UNLOCK for !keep_locked cases) ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ocfs2: handle a symlink read error correctly Patch series "Convert ocfs2 to use folios". Mark did a conversion of ocfs2 to use folios and sent it to me as a giant patch for review ;-) So I've redone it as individual patches, and credited Mark for the patches where his code is substantially the same. It's not a bad way to do it; his patch had some bugs and my patches had some bugs. Hopefully all our bugs were different from each other. And hopefully Mark likes all the changes I made to his code! This patch (of 23): If we can't read the buffer, be sure to unlock the page before returning.

In the Linux kernel, the following vulnerability has been resolved: binfmt_flat: Fix integer overflow bug on 32 bit systems Most of these sizes and counts are capped at 256MB so the math doesn't result in an integer overflow. The "relocs" count needs to be checked as well. Otherwise on 32bit systems the calculation of "full_data" could be wrong. full_data = data_len + relocs * sizeof(unsigned long);

In the Linux kernel, the following vulnerability has been resolved: idpf: convert workqueues to unbound When a workqueue is created with `WQ_UNBOUND`, its work items are served by special worker-pools, whose host workers are not bound to any specific CPU. In the default configuration (i.e. when `queue_delayed_work` and friends do not specify which CPU to run the work item on), `WQ_UNBOUND` allows the work item to be executed on any CPU in the same node of the CPU it was enqueued on. While this solution potentially sacrifices locality, it avoids contention with other processes that might dominate the CPU time of the processor the work item was scheduled on. This is not just a theoretical problem: in a particular scenario misconfigured process was hogging most of the time from CPU0, leaving less than 0.5% of its CPU time to the kworker. The IDPF workqueues that were using the kworker on CPU0 suffered large completion delays as a result, causing performance degradation, timeouts and eventual system crash. * I have also run a manual test to gauge the performance improvement. The test consists of an antagonist process (`./stress --cpu 2`) consuming as much of CPU 0 as possible. This process is run under `taskset 01` to bind it to CPU0, and its priority is changed with `chrt -pQ 9900 10000 ${pid}` and `renice -n -20 ${pid}` after start. Then, the IDPF driver is forced to prefer CPU0 by editing all calls to `queue_delayed_work`, `mod_delayed_work`, etc... to use CPU 0. Finally, `ktraces` for the workqueue events are collected. Without the current patch, the antagonist process can force arbitrary delays between `workqueue_queue_work` and `workqueue_execute_start`, that in my tests were as high as `30ms`. With the current patch applied, the workqueue can be migrated to another unloaded CPU in the same node, and, keeping everything else equal, the maximum delay I could see was `6us`.

In the Linux kernel, the following vulnerability has been resolved: udp: Fix memory accounting leak. Matt Dowling reported a weird UDP memory usage issue. Under normal operation, the UDP memory usage reported in /proc/net/sockstat remains close to zero. However, it occasionally spiked to 524,288 pages and never dropped. Moreover, the value doubled when the application was terminated. Finally, it caused intermittent packet drops. We can reproduce the issue with the script below [0]: 1. /proc/net/sockstat reports 0 pages # cat /proc/net/sockstat | grep UDP: UDP: inuse 1 mem 0 2. Run the script till the report reaches 524,288 # python3 test.py & sleep 5 # cat /proc/net/sockstat | grep UDP: UDP: inuse 3 mem 524288 <-- (INT_MAX + 1) >> PAGE_SHIFT 3. Kill the socket and confirm the number never drops # pkill python3 && sleep 5 # cat /proc/net/sockstat | grep UDP: UDP: inuse 1 mem 524288 4. (necessary since v6.0) Trigger proto_memory_pcpu_drain() # python3 test.py & sleep 1 && pkill python3 5. The number doubles # cat /proc/net/sockstat | grep UDP: UDP: inuse 1 mem 1048577 The application set INT_MAX to SO_RCVBUF, which triggered an integer overflow in udp_rmem_release(). When a socket is close()d, udp_destruct_common() purges its receive queue and sums up skb->truesize in the queue. This total is calculated and stored in a local unsigned integer variable. The total size is then passed to udp_rmem_release() to adjust memory accounting. However, because the function takes a signed integer argument, the total size can wrap around, causing an overflow. Then, the released amount is calculated as follows: 1) Add size to sk->sk_forward_alloc. 2) Round down sk->sk_forward_alloc to the nearest lower multiple of PAGE_SIZE and assign it to amount. 3) Subtract amount from sk->sk_forward_alloc. 4) Pass amount >> PAGE_SHIFT to __sk_mem_reduce_allocated(). When the issue occurred, the total in udp_destruct_common() was 2147484480 (INT_MAX + 833), which was cast to -2147482816 in udp_rmem_release(). At 1) sk->sk_forward_alloc is changed from 3264 to -2147479552, and 2) sets -2147479552 to amount. 3) reverts the wraparound, so we don't see a warning in inet_sock_destruct(). However, udp_memory_allocated ends up doubling at 4). Since commit 3cd3399dd7a8 ("net: implement per-cpu reserves for memory_allocated"), memory usage no longer doubles immediately after a socket is close()d because __sk_mem_reduce_allocated() caches the amount in udp_memory_per_cpu_fw_alloc. However, the next time a UDP socket receives a packet, the subtraction takes effect, causing UDP memory usage to double. This issue makes further memory allocation fail once the socket's sk->sk_rmem_alloc exceeds net.ipv4.udp_rmem_min, resulting in packet drops. To prevent this issue, let's use unsigned int for the calculation and call sk_forward_alloc_add() only once for the small delta. Note that first_packet_length() also potentially has the same problem. [0]: from socket import * SO_RCVBUFFORCE = 33 INT_MAX = (2 ** 31) - 1 s = socket(AF_INET, SOCK_DGRAM) s.bind(('', 0)) s.setsockopt(SOL_SOCKET, SO_RCVBUFFORCE, INT_MAX) c = socket(AF_INET, SOCK_DGRAM) c.connect(s.getsockname()) data = b'a' * 100 while True: c.send(data)