A vulnerability, which was classified as critical, was found in Belkin F9K1122 1.00.33. This affects the function formPPPoESetup of the file /goform/formPPPoESetup of the component webs. The manipulation of the argument pppUserName leads to stack-based buffer overflow. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been found in Belkin F9K1122 1.00.33 and classified as critical. This vulnerability affects the function formWlanSetupWPS of the file /goform/formWlanSetupWPS of the component webs. The manipulation of the argument wps_enrolee_pin/webpage leads to stack-based buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Belkin F9K1122 1.00.33. It has been declared as critical. This vulnerability affects the function formWpsStart of the file /goform/formWpsStart of the component webs. The manipulation of the argument pinCode leads to stack-based buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Belkin F9K1122 1.00.33. It has been classified as critical. Affected is the function formWlanMP of the file /goform/formWlanMP of the component webs. The manipulation of the argument ateFunc/ateGain/ateTxCount/ateChan/ateRate/ateMacID/e2pTxPower1/e2pTxPower2/e2pTxPower3/e2pTxPower4/e2pTxPower5/e2pTxPower6/e2pTxPower7/e2pTx2Power1/e2pTx2Power2/e2pTx2Power3/e2pTx2Power4/e2pTx2Power5/e2pTx2Power6/e2pTx2Power7/ateTxFreqOffset/ateMode/ateBW/ateAntenna/e2pTxFreqOffset/e2pTxPwDeltaB/e2pTxPwDeltaG/e2pTxPwDeltaMix/e2pTxPwDeltaN/readE2P leads to stack-based buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Belkin F9K1122 1.00.33. It has been rated as critical. This issue affects the function formiNICWpsStart of the file /goform/formiNICWpsStart of the component webs. The manipulation of the argument pinCode leads to stack-based buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability classified as critical has been found in Belkin F9K1122 1.00.33. Affected is the function formPPTPSetup of the file /goform/formPPTPSetup of the component webs. The manipulation of the argument pptpUserName leads to stack-based buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Belkin F9K1122 1.00.33. It has been declared as critical. Affected by this vulnerability is the function formSetLanguage of the file /goform/formSetLanguage of the component webs. The manipulation of the argument webpage leads to stack-based buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Belkin F9K1122 1.00.33. It has been rated as critical. Affected by this issue is the function formBSSetSitesurvey of the file /goform/formBSSetSitesurvey of the component webs. The manipulation of the argument submit-url-ok leads to stack-based buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability, which was classified as critical, has been found in Belkin F9K1122 1.00.33. Affected by this issue is the function formConnectionSetting of the file /goform/formConnectionSetting of the component webs. The manipulation of the argument max_Conn/timeOut leads to stack-based buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Belkin F9K1122 1.00.33 and classified as critical. This issue affects the function formWanTcpipSetup of the file /goform/formWanTcpipSetup of the component webs. The manipulation of the argument pppUserName leads to stack-based buffer overflow. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

The administration web interface on Belkin Linksys WRT160NL 1.0.04.002_US_20130619 devices allows remote authenticated attackers to execute system commands with root privileges via shell metacharacters in the ui_language POST parameter to the apply.cgi form endpoint. This occurs in do_upgrade_post in mini_httpd. NOTE: This vulnerability only affects products that are no longer supported by the maintaine

A vulnerability was found in Belkin F9K1122 1.00.33 and classified as critical. Affected by this issue is the function formBSSetSitesurvey of the file /goform/formBSSetSitesurvey of the component webs. The manipulation of the argument wan_ipaddr/wan_netmask/wan_gateway/wl_ssid is directly passed by the attacker/so we can control the wan_ipaddr/wan_netmask/wan_gateway/wl_ssid leads to os command injection. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been found in Belkin F9K1122 1.00.33 and classified as critical. Affected by this vulnerability is the function formSetWanStatic of the file /goform/formSetWanStatic of the component webs. The manipulation of the argument m_wan_ipaddr/m_wan_netmask/m_wan_gateway/m_wan_staticdns1/m_wan_staticdns2 is directly passed by the attacker/so we can control the m_wan_ipaddr/m_wan_netmask/m_wan_gateway/m_wan_staticdns1/m_wan_staticdns2 leads to os command injection. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Belkin F9K1122 1.00.33. It has been classified as critical. This affects the function mp of the file /goform/mp of the component webs. The manipulation of the argument command leads to os command injection. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

Belkin N300 Dual-Band Wi-Fi Range Extender with firmware before 1.04.10 allows remote authenticated users to execute arbitrary commands via the (1) sub_dir parameter in a formUSBStorage request; pinCode parameter in a (2) formWpsStart or (3) formiNICWpsStart request; (4) wps_enrolee_pin parameter in a formWlanSetupWPS request; or unspecified parameters in a (5) formWlanMP, (6) formBSSetSitesurvey, (7) formHwSet, or (8) formConnectionSetting request.

Belkin LINKSYS WRT160NL 1.0.04.002_US_20130619 devices have a stack-based buffer overflow vulnerability because of sprintf in create_dir in mini_httpd. Successful exploitation leads to arbitrary code execution. NOTE: This vulnerability only affects products that are no longer supported by the maintainer

A Stack-based Buffer Overflow vulnerability in libbelkin_api.so component of Belkin WeMo Insight Switch firmware allows a local attacker to obtain code execution on the device. This issue affects: Belkin WeMo Insight Switch firmware version 2.00.11396 and prior versions.

Buffer overflow in login.cgi in MiniHttpd in Belkin N750 Router with firmware before F9K1103_WW_1.10.17m allows remote attackers to execute arbitrary code via a long string in the jump parameter.

A remote unauthenticated user can overflow a stack buffer in the Belkin N750 using firmware version 1.10.22 by sending a crafted HTTP request to proxy.cgi.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides UPnP services that are available on port 3480 and can also be accessed via port 80 using the url "/port_3480". It seems that the UPnP services provide "request_image" as one of the service actions for a normal user to retrieve an image from a camera that is controlled by the controller. It seems that the "res" (resolution) parameter passed in the query string is not sanitized and is stored on the stack which allows an attacker to overflow the buffer. The function "LU::Generic_IP_Camera_Manager::REQ_Image" is activated when the lu_request_image is passed as the "id" parameter in the query string. This function then calls "LU::Generic_IP_Camera_Manager::GetUrlFromArguments". This function retrieves all the parameters passed in the query string including "res" and then uses the value passed in it to fill up buffer using the sprintf function. However, the function in this case lacks a simple length check and as a result an attacker who is able to send more than 184 characters can easily overflow the values stored on the stack including the $RA value and thus execute code on the device.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides UPnP services that are available on port 3480 and can also be accessed via port 80 using the url "/port_3480". It seems that the UPnP services provide "request_image" as one of the service actions for a normal user to retrieve an image from a camera that is controlled by the controller. It seems that the "URL" parameter passed in the query string is not sanitized and is stored on the stack which allows an attacker to overflow the buffer. The function "LU::Generic_IP_Camera_Manager::REQ_Image" is activated when the lu_request_image is passed as the "id" parameter in query string. This function then calls "LU::Generic_IP_Camera_Manager::GetUrlFromArguments" and passes a "pointer" to the function where it will be allowed to store the value from the URL parameter. This pointer is passed as the second parameter $a2 to the function "LU::Generic_IP_Camera_Manager::GetUrlFromArguments". However, neither the callee or the caller in this case performs a simple length check and as a result an attacker who is able to send more than 1336 characters can easily overflow the values stored on the stack including the $RA value and thus execute code on the device.

Multiple buffer overflows in the ctl_put* functions in NTP before 4.2.8p10 and 4.3.x before 4.3.94 allow remote authenticated users to have unspecified impact via a long variable.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities.

A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device.  The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability.

VMware ESXi (6.0 before ESXi600-201711101-SG, 5.5 ESXi550-201709101-SG), Workstation (12.x before 12.5.8), and Fusion (8.x before 8.5.9) contain a vulnerability that could allow an authenticated VNC session to cause a stack overflow via a specific set of VNC packets. Successful exploitation of this issue could result in remote code execution in a virtual machine via the authenticated VNC session. Note: In order for exploitation to be possible in ESXi, VNC must be manually enabled in a virtual machine's .vmx configuration file. In addition, ESXi must be configured to allow VNC traffic through the built-in firewall.

Multiple vulnerabilities in the web-based management interface of Cisco Small Business RV016, RV042, RV042G, RV082, RV320, and RV325 Routers could allow an authenticated, remote attacker to execute arbitrary code or cause an affected device to restart unexpectedly. These vulnerabilities are due to improper validation of user-supplied input in the web-based management interface. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to execute arbitrary code as the root user on the underlying operating system or cause the device to reload, resulting in a denial of service (DoS) condition. To exploit these vulnerabilities, an attacker would need to have valid administrator credentials on the affected device.

A vulnerability has been identified in POWER METER SICAM Q100 (All versions < V2.41), POWER METER SICAM Q100 (All versions < V2.41), POWER METER SICAM Q100 (All versions < V2.41), POWER METER SICAM Q100 (All versions < V2.41). The affected firmware contains a buffer overflow vulnerability in the web application that could allow a remote attacker with engineer or admin priviliges to potentially perform remote code execution.

A vulnerability has been found in Linksys E1700 1.0.0.4.003. Affected by this issue is the function setSysAdm of the file /goform/setSysAdm. Such manipulation of the argument rm_port leads to stack-based buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A flaw has been found in Linksys E1700 1.0.0.4.003. Affected by this vulnerability is the function setWan of the file /goform/setWan. This manipulation of the argument DeviceName/lanIp causes stack-based buffer overflow. The attack can be initiated remotely. The exploit has been published and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Linksys E1700 1.0.0.4.003. This affects the function QoSSetup of the file /goform/QoSSetup. Performing manipulation of the argument ack_policy results in stack-based buffer overflow. The attack may be initiated remotely. The exploit has been made public and could be used. The vendor was contacted early about this disclosure but did not respond in any way.

Buffer overflow in the glob implementation (glob.c) in libc in NetBSD-current before 20050914, NetBSD 2.* and 3.* before 20061203, and Apple Mac OS X before 2007-004, as used by the FTP daemon and tnftpd, allows remote authenticated users to execute arbitrary code via a long pathname that results from path expansion.

Apache PLC4X - PLC4C (Only the C language implementation was effected) was vulnerable to an unsigned integer underflow flaw inside the tcp transport. Users should update to 0.9.1, which addresses this issue. However, in order to exploit this vulnerability, a user would have to actively connect to a mallicious device which could send a response with invalid content. Currently we consider the probability of this being exploited as quite minimal, however this could change in the future, especially with the industrial networks growing more and more together.

An exploitable remote code execution vulnerability exists in the iw_webs configuration parsing functionality of the Moxa AWK-3131A firmware version 1.13. A specially crafted user name entry can cause an overflow of an error message buffer, resulting in remote code execution. An attacker can send commands while authenticated as a low privilege user to trigger this vulnerability.

A buffer overflow vulnerability in "Add command" functionality exists in Flexense SyncBreeze Enterprise <= 10.3.14. The vulnerability can be triggered by an authenticated attacker who submits more than 5000 characters as the command name. It will cause termination of the SyncBreeze Enterprise server and possibly remote command execution with SYSTEM privilege.

A vulnerability classified as critical was found in Tenda i21 1.0.0.14(4656). This vulnerability affects the function formGetDiagnoseInfo. The manipulation of the argument cmdinput leads to stack-based buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-263080. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Tenda W15E 15.11.0.14. It has been classified as critical. Affected is the function guestWifiRuleRefresh. The manipulation of the argument qosGuestDownstream leads to stack-based buffer overflow. It is possible to launch the attack remotely. VDB-261870 is the identifier assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

Multiple exploitable buffer overflow vulnerabilities exist in the PubNub message handler for the "cc" channel of Insteon Hub running firmware version 1012. Specially crafted commands sent through the PubNub service can cause a stack-based buffer overflow overwriting arbitrary data. An attacker should send an authenticated HTTP request to trigger this vulnerability. In cmd g_b, at 0x9d015714, the value for the `grp` key is copied using `strcpy` to the buffer at `$sp+0x280`.This buffer is 16 bytes large, sending anything longer will cause a buffer overflow.

A vulnerability, which was classified as critical, was found in Tenda W15E 15.11.0.14. Affected is the function formAddDnsForward of the file /goform/AddDnsForward. The manipulation of the argument DnsForwardRule leads to stack-based buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. VDB-261858 is the identifier assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Tenda i21 1.0.0.14(4656). It has been classified as critical. This affects the function formWifiMacFilterSet. The manipulation of the argument ssidIndex leads to stack-based buffer overflow. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The identifier VDB-263085 was assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in Tenda i21 1.0.0.14(4656) and classified as critical. Affected by this issue is the function formWifiMacFilterGet. The manipulation of the argument index leads to stack-based buffer overflow. The attack may be launched remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-263084. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

Vyper is a Pythonic Smart Contract Language for the EVM. In affected versions when performing a function call inside a literal struct, there is a memory corruption issue that occurs because of an incorrect pointer to the the top of the stack. This issue has been resolved in version 0.3.0.

Buffer overflow in logout.cgi in the Intelligent Platform Management Interface (IPMI) with firmware before 3.15 (SMT_X9_315) on Supermicro X9 generation motherboards allows remote authenticated users to execute arbitrary code via the SID parameter.

A vulnerability was found in Tenda i21 1.0.0.14(4656). It has been declared as critical. This vulnerability affects the function formexeCommand. The manipulation of the argument cmdinput leads to stack-based buffer overflow. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. VDB-263086 is the identifier assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability, which was classified as critical, was found in Tenda i21 1.0.0.14(4656). Affected is the function formSetAutoPing. The manipulation of the argument ping1/ping2 leads to stack-based buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. VDB-263082 is the identifier assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability has been found in Tenda i21 1.0.0.14(4656) and classified as critical. Affected by this vulnerability is the function formSetUplinkInfo of the file /goform/setUplinkInfo. The manipulation of the argument pingHostIp2 leads to stack-based buffer overflow. The attack can be launched remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-263083. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

Buffer overflow in the SNMP implementation in Cisco NX-OS on Nexus 7000 devices 4.x and 5.x before 5.2(5) and 6.x before 6.1(1) and MDS 9000 devices 4.x and 5.x before 5.2(5) allows remote authenticated users to execute arbitrary code via a crafted SNMP request, aka Bug ID CSCtx54822.