Devices in the Linksys ESeries line of routers (Linksys E1200 Firmware Version 2.0.09 and Linksys E2500 Firmware Version 3.0.04) are susceptible to OS command injection vulnerabilities due to improper filtering of data passed to and retrieved from NVRAMData entered into the 'Router Name' input field through the web portal is submitted to apply.cgi as the value to the 'machine_name' POST parameter. When the 'preinit' binary receives the SIGHUP signal it enters a code path that calls a function named 'set_host_domain_name' from its libshared.so shared object.

An exploitable operating system command injection exists in the Linksys ESeries line of routers (Linksys E1200 Firmware Version 2.0.09 and Linksys E2500 Firmware Version 3.0.04). Specially crafted entries to network configuration information can cause execution of arbitrary system commands, resulting in full control of the device. An attacker can send an authenticated HTTP request to trigger this vulnerability. Data entered into the 'Domain Name' input field through the web portal is submitted to apply.cgi as the value to the 'wan_domain' POST parameter. The wan_domain data goes through the nvram_set process described above. When the 'preinit' binary receives the SIGHUP signal it enters a code path that calls a function named 'set_host_domain_name' from its libshared.so shared object.

Devices in the Linksys ESeries line of routers (Linksys E1200 Firmware Version 2.0.09 and Linksys E2500 Firmware Version 3.0.04) are susceptible to OS command injection vulnerabilities due to improper filtering of data passed to and retrieved from NVRAM. Data entered into the 'Router Name' input field through the web portal is submitted to apply.cgi as the value to the 'machine_name' POST parameter. When the 'preinit' binary receives the SIGHUP signal, it enters a code path that continues until it reaches offset 0x0042B5C4 in the 'start_lltd' function. Within the 'start_lltd' function, a 'nvram_get' call is used to obtain the value of the user-controlled 'machine_name' NVRAM entry. This value is then entered directly into a command intended to write the host name to a file and subsequently executed.

An exploitable command injection vulnerability exists in the way Netgate pfSense CE 2.4.4-RELEASE processes the parameters of a specific POST request. The attacker can exploit this and gain the ability to execute arbitrary commands on the system. An attacker needs to be able to send authenticated POST requests to the administration web interface. Command injection is possible in the `powerd_normal_mode` parameter.

Blinko is an AI-powered card note-taking project. Prior to version 1.8.4, the MCP (Model Context Protocol) server creation function allows specifying arbitrary commands and arguments, which are executed when testing the connection. This issue has been patched in version 1.8.4.

meterN 1.2.3 contains an authenticated remote code execution vulnerability in admin_meter2.php and admin_indicator2.php scripts. Attackers can exploit the 'COMMANDx' and 'LIVECOMMANDx' POST parameters to execute arbitrary system commands with administrative privileges.

LiteSpeed Web Server Enterprise 5.4.11 contains an authenticated command injection vulnerability in the external app configuration interface. Authenticated administrators can inject shell commands through the 'Command' parameter in the server configuration, allowing remote code execution via path traversal and bash command injection.

UD-LT1 firmware Ver.2.1.9 and earlier and UD-LT1/EX firmware Ver.2.1.9 and earlier allow a remote authenticated attacker with an administrative account to execute arbitrary OS commands.

TRENDnet TEW-673GRU v1.00b40 devices have an OS command injection vulnerability in the start_arpping function of the timer binary, which allows remote attackers to execute arbitrary commands via three parameters (dhcpd_start, dhcpd_end, and lan_ipaddr) passed to the apply.cgi binary through a POST request.

An issue was discovered on Foscam C2 devices with System Firmware 1.11.1.8 and Application Firmware 2.72.1.32, and Opticam i5 devices with System Firmware 1.5.2.11 and Application Firmware 2.21.1.128. They allow remote attackers to execute arbitrary OS commands via shell metacharacters in the usrName parameter of a CGIProxy.fcgi addAccount action.

An issue was discovered on Foscam C2 devices with System Firmware 1.11.1.8 and Application Firmware 2.72.1.32, and Opticam i5 devices with System Firmware 1.5.2.11 and Application Firmware 2.21.1.128. They allow attackers to execute arbitrary OS commands via shell metacharacters in the modelName, by leveraging /mnt/mtd/app/config/ProductConfig.xml write access.

Cypress Solutions CTM-200 2.7.1 contains an authenticated command injection vulnerability in the firmware upgrade script that allows remote attackers to execute shell commands. Attackers can exploit the 'fw_url' parameter in the ctm-config-upgrade.sh script to inject and execute arbitrary commands with root privileges.

The Port Forwarding functionality on DASAN H660GW devices allows remote attackers to execute arbitrary code via shell metacharacters in the cgi-bin/adv_nat_virsvr.asp Addr parameter (aka the Local IP Address field).

home 5G HR02, Wi-Fi STATION SH-52B, and Wi-Fi STATION SH-54C contain an OS command injection vulnerability in the HOST name configuration screen. An arbitrary OS command may be executed with the root privilege by an administrative user.

Aterm WF1200CR and Aterm WG1200CR (Aterm WF1200CR firmware Ver1.1.1 and earlier, Aterm WG1200CR firmware Ver1.0.1 and earlier) allows authenticated attackers to execute arbitrary OS commands via unspecified vectors.

Pydio 4.2.1 through 8.2.1 has an authenticated remote code execution vulnerability in which an attacker with administrator access to the web application can execute arbitrary code on the underlying system via Command Injection.

The web management console of Opsview Monitor 5.4.x before 5.4.2 provides functionality accessible by an authenticated administrator to test notifications that are triggered under certain configurable events. The value parameter is not properly sanitized, leading to arbitrary command injection with the privileges of the nagios user account.

System command injection in User.create method in Buffalo TS5600D1206 version 3.61-0.10 allows attackers to execute system commands via the "name" parameter.

System Command Injection in network.set_auth_settings in Buffalo TS5600D1206 version 3.70-0.10 allows attackers to execute system commands via the adminUsername and adminPassword parameters.

System command injection in ajaxdata.php in TerraMaster TOS version 3.1.03 allows attackers to execute system commands during group creation via the "groupname" parameter.

D-Link DIR-846 devices with firmware 100.26 allow remote attackers to execute arbitrary code as root via a SetNetworkTomographySettings request by leveraging admin access.

Quest DR Series Disk Backup software version before 4.0.3.1 allows command injection (issue 42 of 46).

Quest DR Series Disk Backup software version before 4.0.3.1 allows command injection (issue 9 of 46).

D-Link DIR-615 2.5.17 devices allow Remote Code Execution via shell metacharacters in the Host field of the System / Traceroute screen.

Aterm HC100RC Ver1.0.1 and earlier allows attacker with administrator rights to execute arbitrary OS commands via export.cgi encKey parameter.

Aterm HC100RC Ver1.0.1 and earlier allows attacker with administrator rights to execute arbitrary OS commands via tools_firmware.cgi date parameter, time parameter, and offset parameter.

Aterm WG1200HP firmware Ver1.0.31 and earlier allows attacker with administrator rights to execute arbitrary OS commands via sysCmd in formWsc parameter.

Aterm WG1200HP firmware Ver1.0.31 and earlier allows attacker with administrator rights to execute arbitrary OS commands via targetAPSsid parameter.

Command injection vulnerability in change password of QNAP Q'center Virtual Appliance version 1.7.1063 and earlier could allow authenticated users to run arbitrary commands.

Aterm W300P Ver1.0.13 and earlier allows attacker with administrator rights to execute arbitrary OS commands via HTTP request and response.

Aterm W300P Ver1.0.13 and earlier allows attacker with administrator rights to execute arbitrary OS commands via sysCmd parameter.

Aterm W300P Ver1.0.13 and earlier allows attacker with administrator rights to execute arbitrary OS commands via targetAPSsid parameter.

Aterm HC100RC Ver1.0.1 and earlier allows attacker with administrator rights to execute arbitrary OS commands via FactoryPassword parameter of a certain URL, different URL from CVE-2018-0634.

Aterm HC100RC Ver1.0.1 and earlier allows attacker with administrator rights to execute arbitrary OS commands via FactoryPassword parameter or bootmode parameter of a certain URL.

An OS Command Injection vulnerability in Fortinet FortiWLC 6.1-2 through 6.1-5, 7.0-7 through 7.0-10, 8.0 through 8.2, and 8.3.0 through 8.3.2 file management AP script download webUI page allows an authenticated admin user to execute arbitrary system console commands via crafted HTTP requests.

Dell EMC Unity Operating Environment (OE) versions prior to 4.3.0.1522077968 are affected by multiple OS command injection vulnerabilities. A remote application admin user could potentially exploit the vulnerabilities to execute arbitrary OS commands as system root on the system where Dell EMC Unity is installed.

An authenticated OS command injection vulnerability exists in Netgear routers (tested on the DGN1000B model firmware versions 1.1.00.24 and 1.1.00.45) via the TimeToLive parameter in the setup.cgi endpoint. The vulnerability arises from improper input neutralization, enabling command injection through crafted POST requests. This flaw enables remote attackers to deploy payloads or manipulate system state post-authentication.

An authenticated OS command injection vulnerability exists in various Linksys router models (tested on WRT160Nv2) running firmware version v2.0.03 via the apply.cgi endpoint. The web interface fails to properly sanitize user-supplied input passed to the ping_size parameter during diagnostic operations. An attacker with valid credentials can inject arbitrary shell commands, enabling remote code execution.

An authenticated OS command injection vulnerability exists in various D-Link routers (tested on DIR-615H1 running firmware version 8.04) via the tools_vct.htm endpoint. The web interface fails to sanitize input passed from the ping_ipaddr parameter to the tools_vct.htm diagnostic interface, allowing attackers to inject arbitrary shell commands using backtick encapsulation. With default credentials, an attacker can exploit this blind injection vector to execute arbitrary commands.

An OS command injection vulnerability in the web administration component of Micro Focus Secure Messaging Gateway (SMG) allows a remote attacker authenticated as a privileged user to execute arbitrary OS commands on the SMG server. This can be exploited in conjunction with CVE-2018-12464 to achieve unauthenticated remote code execution. Affects Micro Focus Secure Messaging Gateway versions prior to 471. It does not affect previous versions of the product that used GWAVA product name (i.e. GWAVA 6.5).

lib/rrd.php in Cacti 1.1.27 allows remote authenticated administrators to execute arbitrary OS commands via the path_rrdtool parameter in an action=save request to settings.php.

The Symantec Reporter CLI 10.1 prior to 10.1.5.6 and 10.2 prior to 10.2.1.8 is susceptible to an OS command injection vulnerability. An authenticated malicious administrator with Enable mode access can execute arbitrary OS commands with elevated system privileges.

Aterm HC100RC Ver1.0.1 and earlier allows attacker with administrator rights to execute arbitrary OS commands via filename parameter.

Algo 8028 Control Panel version 3.3.3 contains a command injection vulnerability in the fm-data.lua endpoint that allows authenticated attackers to execute arbitrary commands. Attackers can exploit the insecure 'source' parameter by injecting commands that are executed with root privileges, enabling remote code execution through a crafted POST request.

The EyesOfNetwork web interface (aka eonweb) 5.1-0 allows remote command execution via shell metacharacters in a hosts_cacti array parameter to module/admin_device/index.php.

An os command injection vulnerability exists in the httpd delfile.cgi functionality of Siretta QUARTZ-GOLD G5.0.1.5-210720-141020. A specially-crafted HTTP request can lead to arbitrary command execution. An attacker can send an HTTP request to trigger this vulnerability.

Improper neutralization of special elements used in an OS command ('OS Command Injection') issue exists in WN-7D36QR and WN-7D36QR/UE. If this vulnerability is exploited, an arbitrary OS command may be executed by a remote authenticated attacker.

FutureNet MA and IP-K series provided by Century Systems Co., Ltd. contain an OS command Injection vulnerability. A user who logs in to the Web UI of the product may execute an arbitrary OS command.

A user with specific node group editing permissions and a specially crafted class parameter could be used to execute commands as root on the primary host. It affects Puppet Enterprise versions 2018.1.8 through 2023.8.3 and 2025.3 and has been resolved in versions 2023.8.4 and 2025.4.0.

Netwin SurgeFTP version 23c8 and prior contains a vulnerability in its web-based administrative console that allows authenticated users to execute arbitrary system commands via crafted POST requests to `surgeftpmgr.cgi`. This can lead to full remote code execution on the underlying system.