On PTX Series and QFX10k Series devices with the "inline-jflow" feature enabled, a use after free weakness in the Packet Forwarding Engine (PFE) microkernel architecture of Juniper Networks Junos OS may allow an attacker to cause a Denial of Service (DoS) condition whereby one or more Flexible PIC Concentrators (FPCs) may restart. As this is a race condition situation this issue become more likely to be hit when network instability occurs, such as but not limited to BGP/IGP reconvergences, and/or further likely to occur when more active "traffic flows" are occurring through the device. When this issue occurs, it will cause one or more FPCs to restart unexpectedly. During FPC restarts core files will be generated. While the core file is generated traffic will be disrupted. Sustained receipt of large traffic flows and reconvergence-like situations may sustain the Denial of Service (DoS) situation. This issue affects: Juniper Networks Junos OS: 18.1 version 18.1R2 and later versions prior to 18.1R3-S10 on PTX Series, QFX10K Series.

On Juniper Networks EX and QFX5K Series platforms configured with Redundant Trunk Group (RTG), Storm Control profile applied on the RTG interface might not take affect when it reaches the threshold condition. Storm Control enables the device to monitor traffic levels and to drop broadcast, multicast, and unknown unicast packets when a specified traffic level is exceeded, thus preventing packets from proliferating and degrading the LAN. Note: this issue does not affect EX2200, EX3300, EX4200, and EX9200 Series. This issue affects Juniper Networks Junos OS on EX Series and QFX5K Series: 15.1 versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S5, 18.4R3-S3; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2.

A Denial of Service (DoS) vulnerability in BGP in Juniper Networks Junos OS configured as a VPLS PE allows an attacker to craft a specific BGP message to cause the routing protocol daemon (rpd) process to crash and restart. While rpd restarts after a crash, repeated crashes can result in an extended DoS condition. This issue only affects PE routers configured with BGP Auto discovery for LDP VPLS. Other BGP configurations are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D81; 12.3 versions prior to 12.3R12-S12; 12.3X48 versions prior to 12.3X48-D76; 14.1X53 versions prior to 14.1X53-D48; 15.1 versions prior to 15.1F6-S12, 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D150; 15.1X53 versions prior to 15.1X53-D235, 15.1X53-D495, 15.1X53-D590, 15.1X53-D68; 16.1 versions prior to 16.1R3-S10, 16.1R4-S12, 16.1R6-S6, 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R1-S5, 17.4R2; 18.1 versions prior to 18.1R2-S3, 18.1R3.

Juniper juniper/libslax libslax latest version (as of commit 084ddf6ab4a55b59dfa9a53f9c5f14d192c4f8e5 Commits on Sep 1, 2018) is affected by: Buffer Overflow. The impact is: remote dos. The component is: slaxlexer.c:601(funtion:slaxGetInput). The attack vector is: ./slaxproc --slax-to-xslt POC0.

When the "Intrusion Detection Service" (IDS) feature is configured on Juniper Networks MX series with a dynamic firewall filter using IPv6 source or destination prefix, it may incorrectly match the prefix as /32, causing the filter to block unexpected traffic. This issue affects only IPv6 prefixes when used as source and destination. This issue affects MX Series devices using MS-MPC, MS-MIC or MS-SPC3 service cards with IDS service configured. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S10 on MX Series; 17.4 versions prior to 17.4R3-S3 on MX Series; 18.1 versions prior to 18.1R3-S11 on MX Series; 18.2 versions prior to 18.2R3-S6 on MX Series; 18.3 versions prior to 18.3R3-S4 on MX Series; 18.4 versions prior to 18.4R3-S6 on MX Series; 19.1 versions prior to 19.1R2-S2, 19.1R3-S3 on MX Series; 19.2 versions prior to 19.2R3-S1 on MX Series; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1 on MX Series; 19.4 versions prior to 19.4R3 on MX Series; 20.1 versions prior to 20.1R2 on MX Series; 20.2 versions prior to 20.2R2 on MX Series;

Receipt of a malformed packet on MX Series devices with dynamic vlan configuration can trigger an uncontrolled recursion loop in the Broadband Edge subscriber management daemon (bbe-smgd), and lead to high CPU usage and a crash of the bbe-smgd service. Repeated receipt of the same packet can result in an extended denial of service condition for the device. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S1; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.

On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a certain sequence of BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. Repeated crashes of the RPD process can cause prolonged Denial of Service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S3; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3; 17.2X75 versions prior to 17.2X75-D105; 17.3 versions prior to 17.3R3-S2; 17.4 versions prior to 17.4R1-S7, 17.4R2-S2, 17.4R3; 18.1 versions prior to 18.1R3-S2; 18.2 versions prior to 18.2R2; 18.2X75 versions prior to 18.2X75-D12, 18.2X75-D30; 18.3 versions prior to 18.3R1-S4, 18.3R2. Junos OS releases prior to 16.1R1 are not affected.

Under certain heavy traffic conditions srxpfe process can crash and result in a denial of service condition for the SRX1500 device. Repeated crashes of the srxpfe can result in an extended denial of service condition. The SRX device may fail to forward traffic when this condition occurs. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D170 on SRX1500; 17.3 versions prior to 17.3R3-S7 on SRX1500; 17.4 versions prior to 17.4R2-S8, 17.4R3 on SRX1500; 18.1 versions prior to 18.1R3-S8 on SRX1500; 18.2 versions prior to 18.2R3 on SRX1500; 18.3 versions prior to 18.3R2 on SRX1500; 18.4 versions prior to 18.4R2 on SRX1500.

On QFX and PTX Series, receipt of a malformed packet for J-Flow sampling might crash the FPC (Flexible PIC Concentrator) process which causes all interfaces to go down. By continuously sending the offending packet, an attacker can repeatedly crash the FPC process causing a sustained Denial of Service (DoS). This issue affects both IPv4 and IPv6 packet processing. Affected releases are Juniper Networks Junos OS on QFX and PTX Series: 17.4 versions prior to 17.4R2-S1, 17.4R3; 18.1 versions prior to 18.1R3-S1; 18.2 versions prior to 18.2R1-S3, 18.2R2; 17.2X75 versions prior to 17.2X75-D91, 17.2X75-D100.

The srxpfe process may crash on SRX Series services gateways when the UTM module processes a specific fragmented HTTP packet. The packet is misinterpreted as a regular TCP packet which causes the processor to crash. This issue affects all SRX Series platforms that support URL-Filtering and have web-filtering enabled. Affected releases are Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 17.3 versions on SRX Series; 17.4 versions prior to 17.4R1-S8, 17.4R2-S5, 17.4R3 on SRX Series; 18.1 versions prior to 18.1R3-S6 on SRX Series; 18.2 versions prior to 18.2R2-S1, 18.2R3 on SRX Series; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX Series; 18.4 versions prior to 18.4R1-S1, 18.4R2 on SRX Series.

Receipt of a specific packet on the out-of-band management interface fxp0 may cause the system to crash and restart (vmcore). By continuously sending a specially crafted packet to the fxp0 interface, an attacker can repetitively crash the rpd process causing prolonged Denial of Service (DoS). Affected releases are Juniper Networks SRX5000 Series: 12.1X46 versions prior to 12.1X46-D82; 12.3X48 versions prior to 12.3X48-D80; 15.1X49 versions prior to 15.1X49-D160.

A firewall bypass vulnerability in the proxy ARP service of Juniper Networks Junos OS allows an attacker to cause a high CPU condition leading to a Denial of Service (DoS). This issue affects only IPv4. Affected releases are Juniper Networks Junos OS: 12.1X46 versions above and including 12.1X46-D25 prior to 12.1X46-D71, 12.1X46-D73 on SRX Series; 12.3X48 versions prior to 12.3X48-D50 on SRX Series; 15.1X49 versions prior to 15.1X49-D75 on SRX Series.

An SRX Series Service Gateway configured for Unified Threat Management (UTM) may experience a system crash with the error message "mbuf exceed" -- an indication of memory buffer exhaustion -- due to the receipt of crafted HTTP traffic. Each crafted HTTP packet inspected by UTM consumes mbufs which can be identified through the following log messages: all_logs.0:Jun 8 03:25:03 srx1 node0.fpc4 : SPU3 jmpi mbuf stall 50%. all_logs.0:Jun 8 03:25:13 srx1 node0.fpc4 : SPU3 jmpi mbuf stall 51%. all_logs.0:Jun 8 03:25:24 srx1 node0.fpc4 : SPU3 jmpi mbuf stall 52%. ... Eventually the system runs out of mbufs and the system crashes (fails over) with the error "mbuf exceed". This issue only occurs when HTTP AV inspection is configured. Devices configured for Web Filtering alone are unaffected by this issue. Affected releases are Junos OS on SRX Series: 12.1X46 versions prior to 12.1X46-D81; 12.3X48 versions prior to 12.3X48-D77; 15.1X49 versions prior to 15.1X49-D101, 15.1X49-D110.

On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. By simulating a specific BGP session restart, an attacker can repeatedly crash the RPD process causing prolonged denial of service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S8; 17.1 versions prior to 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R2. Junos OS releases prior to 16.1R1 are not affected.

When a specific BGP flowspec configuration is enabled and upon receipt of a specific matching BGP packet meeting a specific term in the flowspec configuration, a reachable assertion failure occurs, causing the routing protocol daemon (rpd) process to crash with a core file being generated. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D70 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on EX2200/VC, EX3200, EX3300/VC, EX4200, EX4300, EX4550/VC, EX4600, EX6200, EX8200/VC (XRE), QFX3500, QFX3600, QFX5100; 15.1 versions prior to 15.1R3; 15.1F versions prior to 15.1F3; 15.1X49 versions prior to 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400.

In MPLS environments, receipt of a specific SNMP packet may cause the routing protocol daemon (RPD) process to crash and restart. By continuously sending a specially crafted SNMP packet, an attacker can repetitively crash the RPD process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS : 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D48 on EX/QFX series; 15.1 versions prior to 15.1R4-S9, 15.1R7-S2; 15.1F6 versions prior to 15.1F6-S11; 15.1X49 versions prior to 15.1X49-D141, 15.1X49-D144, 15.1X49-D150 on SRX Series; 15.1X53 versions prior to 15.1X53-D234 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D68 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 15.1X53 versions prior to 15.1X53-D590 on EX2300/EX3400 Series; 15.1X54 on ACX Series; 16.1 versions prior to 16.1R3-S10, 16.1R4-S11, 16.1R6-S5, 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S8, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R1-S1, 18.1R2-S1, 18.1R3; 18.2X75 versions prior to 18.2X75-D10.

The routing protocol daemon (RPD) process will crash and restart when a specific invalid IPv4 PIM Join packet is received. While RPD restarts after a crash, repeated crashes can result in an extended Denial of Service (DoS) condition. This issue only affects IPv4 PIM. IPv6 PIM is unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77; 12.3X48 versions prior to 12.3X48-D77; 15.1 versions prior to 15.1F6-S10, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D150; 15.1X53 versions prior to 15.1X53-D233, 15.1X53-D59; 16.1 versions prior to 16.1R3-S8, 16.1R4-S8, 16.1R7; 16.2 versions prior to 16.2R2-S6; 17.1 versions prior to 17.1R2-S6, 17.1R3; 17.2 versions prior to 17.2R2-S3, 17.2R3; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R2.

When BGP tracing is enabled an incoming BGP message may cause the Junos OS routing protocol daemon (rpd) process to crash and restart. While rpd restarts after a crash, repeated crashes can result in an extended DoS condition. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S4, 16.1R7-S5; 16.2 versions prior to 16.2R2-S9, 16.2R3; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3-S1; 17.3 versions prior to 17.3R3-S3, 17.3R3-S4, 17.3R4; 17.4 versions prior to 17.4R1-S7, 17.4R2-S3, 17.4R2-S4, 17.4R3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S4, 18.1R4; 18.2 versions prior to 18.2R2-S2, 18.2R2-S3, 18.2R3; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S3, 18.3R2; 18.4 versions prior to 18.4R1-S2, 18.4R2. This issue does not affect Junos releases prior to 16.1R1.

On SRX5000 Series devices, if 'set security zones security-zone <zone> tcp-rst' is configured, the flowd process may crash when a specific TCP packet is received by the device and triggers a new session. The process restarts automatically. However, receipt of a constant stream of these TCP packets may result in an extended Denial of Service (DoS) condition on the device. This issue affects Juniper Networks Junos OS: 18.2R3 on SRX 5000 Series; 18.4R2 on SRX 5000 Series; 19.2R1 on SRX 5000 Series.

On MX Series, when the SIP ALG is enabled, receipt of a certain malformed SIP packet may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending a crafted SIP packet, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a sustained Denial of Service. This issue affects Juniper Networks Junos OS on MX Series: 16.1 versions prior to 16.1R7-S5; 16.2 versions prior to 16.2R2-S11; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R3-S6 ; 17.4 versions prior to 17.4R2-S8, 17.4R3; 18.1 versions prior to 18.1R3-S3; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2; 18.4 versions prior to 18.4R2.

When an MX Series Broadband Remote Access Server (BRAS) is configured as a Broadband Network Gateway (BNG) with DHCPv6 enabled, jdhcpd might crash when receiving a specific crafted DHCP response message on a subscriber interface. The daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue only affects systems configured with DHCPv6 enabled. DHCPv4 is unaffected by this issue. This issue affects Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S5 on MX Series; 16.1 versions prior to 16.1R7-S5 on MX Series; 16.2 versions prior to 16.2R2-S10 on MX Series; 17.1 versions prior to 17.1R3-S1 on MX Series; 17.2 versions prior to 17.2R3-S2 on MX Series; 17.3 versions prior to 17.3R3-S6 on MX Series; 17.4 versions prior to 17.4R2-S5, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S6 on MX Series; 18.2 versions prior to 18.2R2-S4, 18.2R3 on MX Series; 18.2X75 versions prior to 18.2X75-D50 on MX Series; 18.3 versions prior to 18.3R1-S5, 18.3R3 on MX Series; 18.4 versions prior to 18.4R2 on MX Series; 19.1 versions prior to 19.1R1-S2, 19.1R2 on MX Series.

An Operation on a Resource after Expiration or Release vulnerability in the Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker with an established BGP session to cause a Denial of Service (DoS). This issue occurs when proxy-generate route-target filtering is enabled, and certain proxy-route add and delete events are happening. This issue affects: Juniper Networks Junos OS All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S8, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S2, 20.3R2. Juniper Networks Junos OS Evolved All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R3-EVO; 20.3 versions prior to 20.3R2-EVO.

A vulnerability in the Routing Protocols Daemon (RPD) with Juniper Extension Toolkit (JET) support can allow a network based unauthenticated attacker to cause a severe memory exhaustion condition on the device. This can have an adverse impact on the system performance and availability. This issue only affects devices with JET support running Junos OS 17.2R1 and subsequent releases. Other versions of Junos OS are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R1-S5, 17.4R2; 18.1 versions prior to 18.1R2-S3, 18.1R3;

Receipt of a specific MPLS packet may cause MPC7/8/9, PTX-FPC3 (FPC-P1, FPC-P2) line cards or PTX1K to crash and restart. By continuously sending specific MPLS packets, an attacker can repeatedly crash the line cards or PTX1K causing a sustained Denial of Service. Affected releases are Juniper Networks Junos OS with MPC7/8/9 or PTX-FPC3 (FPC-P1, FPC-P2) installed and PTX1K: 15.1F versions prior to 15.1F6-S10; 15.1 versions prior to 15.1R4-S9, 15.1R6-S6, 15.1R7; 16.1 versions prior to 16.1R3-S8, 16.1R4-S9, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.1X65 versions prior to 16.1X65-D46; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S4, 17.2R2-S4, 17.2R3; 17.2X75 versions prior to 17.2X75-D70, 17.2X75-D90; 17.3 versions prior to 17.3R1-S4, 17.3R2, 17.4 versions prior to 17.4R1-S2, 17.4R2. Refer to KB25385 for more information about PFE line cards.

On SRX Series and MX Series devices with a Service PIC with any ALG enabled, a crafted TCP/IP response packet processed through the device results in memory corruption leading to a flowd daemon crash. Sustained crafted response packets lead to repeated crashes of the flowd daemon which results in an extended Denial of Service condition. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D60 on SRX series; 12.3X48 versions prior to 12.3X48-D35 on SRX series; 14.1 versions prior to 14.1R9 on MX series; 14.2 versions prior to 14.2R8 on MX series; 15.1X49 versions prior to 15.1X49-D60 on SRX series; 15.1 versions prior to 15.1R5-S8, 15.1F6-S9, 15.1R6-S4, 15.1R7 on MX series; 16.1 versions prior to 16.1R6 on MX series; 16.2 versions prior to 16.2R3 on MX series; 17.1 versions prior to 17.1R2-S4, 17.1R3 on MX series. No other Juniper Networks products or platforms are affected by this issue.

Receipt of specially crafted UDP/IP packets over MPLS may be able to bypass a stateless firewall filter. The crafted UDP packets must be encapsulated and meet a very specific packet format to be classified in a way that bypasses IP firewall filter rules. The packets themselves do not cause a service interruption (e.g. RPD crash), but receipt of a high rate of UDP packets may be able to contribute to a denial of service attack. This issue only affects processing of transit UDP/IP packets over MPLS, received on an interface with MPLS enabled. TCP packet processing and non-MPLS encapsulated UDP packet processing are unaffected by this issue. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D76; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D66, 12.3X48-D70; 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1F6-S10, 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D131, 15.1X49-D140; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400; 15.1X53 versions prior to 15.1X53-D67 on QFX10K; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX; 16.1 versions prior to 16.1R3-S8, 16.1R4-S9, 16.1R5-S4, 16.1R6-S3, 16.1R7; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.2X75 versions prior to 17.2X75-D100; 17.3 versions prior to 17.3R1-S4, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.1 versions prior to 18.1R2; 18.2X75 versions prior to 18.2X75-D5.

A Junos device with VPLS routing-instances configured on one or more interfaces may be susceptible to an mbuf leak when processing a specific MPLS packet. Approximately 1 mbuf is leaked per each packet processed. The number of mbufs is platform dependent. The following command provides the number of mbufs that are currently in use and maximum number of mbufs that can be allocated on a platform: > show system buffers 2437/3143/5580 mbufs in use (current/cache/total) Once the device runs out of mbufs it will become inaccessible and a restart will be required. This issue only affects end devices, transit devices are not affected. Affected releases are Juniper Networks Junos OS with VPLS configured running: 12.1X46 versions prior to 12.1X46-D76; 12.3X48 versions prior to 12.3X48-D66, 12.3X48-D70; 14.1 versions prior to 14.1R9; 14.1X53 versions prior to 14.1X53-D47; 14.2 versions prior to 14.2R8; 15.1 versions prior to 15.1F2-S19, 15.1F6-S10, 15.1R4-S9, 15.1R5-S7, 15.1R6-S4, 15.1R7; 15.1X49 versions prior to 15.1X49-D131, 15.1X49-D140; 15.1X53 versions prior to 15.1X53-D58 on EX2300/EX3400; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110; 15.1X53 versions prior to 15.1X53-D471 on NFX; 15.1X53 versions prior to 15.1X53-D66 on QFX10; 16.1 versions prior to 16.1R3-S8, 16.1R4-S6, 16.1R5; 16.2 versions prior to 16.2R1-S6, 16.2R2-S5, 16.2R3; 17.1 versions prior to 17.1R1-S7, 17.1R2-S6, 17.1R3; 17.2 versions prior to 17.2R1-S5, 17.2R2.

An issue was discovered in libslax through v0.22.1. A NULL pointer dereference exists in the function slaxLexer() located in slaxlexer.c. It allows an attacker to cause Denial of Service.

BIND was improperly sequencing cleanup operations on upstream recursion fetch contexts, leading in some cases to a use-after-free error that can trigger an assertion failure and crash in named. Affects BIND 9.0.0 to 9.8.x, 9.9.0 to 9.9.11, 9.10.0 to 9.10.6, 9.11.0 to 9.11.2, 9.9.3-S1 to 9.9.11-S1, 9.10.5-S1 to 9.10.6-S1, 9.12.0a1 to 9.12.0rc1.

On Juniper Networks products or platforms running Junos OS 12.1X46 prior to 12.1X46-D50, 12.1X47 prior to 12.1X47-D40, 12.3 prior to 12.3R13, 12.3X48 prior to 12.3X48-D30, 13.2X51 prior to 13.2X51-D40, 13.3 prior to 13.3R10, 14.1 prior to 14.1R8, 14.1X53 prior to 14.1X53-D35, 14.1X55 prior to 14.1X55-D35, 14.2 prior to 14.2R5, 15.1 prior to 15.1F6 or 15.1R3, 15.1X49 prior to 15.1X49-D30 or 15.1X49-D40, 15.1X53 prior to 15.1X53-D35, and where RIP is enabled, certain RIP advertisements received by the router may cause the RPD daemon to crash resulting in a denial of service condition.

An MS-MPC or MS-MIC Service PIC may crash when large fragmented packets are passed through an Application Layer Gateway (ALG). Repeated crashes of the Service PC can result in an extended denial of service condition. The issue can be seen only if NAT or stateful-firewall rules are configured with ALGs enabled. This issue was caused by the code change for PR 1182910 in Junos OS 14.1X55-D30, 14.1X55-D35, 14.2R7, 15.1R5, and 16.1R2. No other versions of Junos OS and no other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS on MX platforms running: 14.1X55 from 14.1X55-D30 to releases prior to 14.1X55-D35; 14.2R from 14.2R7 to releases prior to 14.2R7-S4, 14.2R8; 15.1R from 15.1R5 to releases prior to 15.1R5-S2, 15.1R6; 16.1R from 16.1R2 to releases prior to 16.1R3-S2, 16.1R4.

On Juniper Networks products or platforms running Junos OS 11.4 prior to 11.4R13-S3, 12.1X46 prior to 12.1X46-D60, 12.3 prior to 12.3R12-S2 or 12.3R13, 12.3X48 prior to 12.3X48-D40, 13.2X51 prior to 13.2X51-D40, 13.3 prior to 13.3R10, 14.1 prior to 14.1R8, 14.1X53 prior to 14.1X53-D12 or 14.1X53-D35, 14.1X55 prior to 14.1X55-D35, 14.2 prior to 14.2R7, 15.1 prior to 15.1F6 or 15.1R3, 15.1X49 prior to 15.1X49-D60, 15.1X53 prior to 15.1X53-D30 and DHCPv6 enabled, when a crafted DHCPv6 packet is received from a subscriber, jdhcpd daemon crashes and restarts. Repeated crashes of the jdhcpd process may constitute an extended denial of service condition for subscribers attempting to obtain IPv6 addresses.

On Juniper Networks SRX Series Services Gateways chassis clusters running Junos OS 12.1X46 prior to 12.1X46-D65, 12.3X48 prior to 12.3X48-D40, 12.3X48 prior to 12.3X48-D60, flowd daemon on the primary node of an SRX Series chassis cluster may crash and restart when attempting to synchronize a multicast session created via crafted multicast packets.

On Juniper Networks EX Series Ethernet Switches running affected Junos OS versions, a vulnerability in IPv6 processing has been discovered that may allow a specially crafted IPv6 Neighbor Discovery (ND) packet destined to an EX Series Ethernet Switch to cause a slow memory leak. A malicious network-based packet flood of these crafted IPv6 NDP packets may eventually lead to resource exhaustion and a denial of service. The affected Junos OS versions are: 12.3 prior to 12.3R12-S4, 12.3R13; 13.3 prior to 13.3R10; 14.1 prior to 14.1R8-S3, 14.1R9; 14.1X53 prior ro 14.1X53-D12, 14.1X53-D40; 14.1X55 prior to 14.1X55-D35; 14.2 prior to 14.2R6-S4, 14.2R7-S6, 14.2R8; 15.1 prior to 15.1R5; 16.1 before 16.1R3; 16.2 before 16.2R1-S3, 16.2R2. 17.1R1 and all subsequent releases have a resolution for this vulnerability.

The Juniper Enhanced jdhcpd daemon may experience high CPU utilization, or crash and restart upon receipt of an invalid IPv6 UDP packet. Both high CPU utilization and repeated crashes of the jdhcpd daemon can result in a denial of service as DHCP service is interrupted. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 14.1X53 prior to 14.1X53-D12, 14.1X53-D38, 14.1X53-D40 on QFX, EX, QFabric System; 15.1 prior to 15.1F2-S18, 15.1R4 on all products and platforms; 15.1X49 prior to 15.1X49-D80 on SRX; 15.1X53 prior to 15.1X53-D51, 15.1X53-D60 on NFX, QFX, EX.

On Juniper Networks products or platforms running Junos OS 12.1X46 prior to 12.1X46-D55, 12.1X47 prior to 12.1X47-D45, 12.3R13 prior to 12.3R13, 12.3X48 prior to 12.3X48-D35, 13.3 prior to 13.3R10, 14.1 prior to 14.1R8, 14.1X53 prior to 14.1X53-D40, 14.1X55 prior to 14.1X55-D35, 14.2 prior to 14.2R6, 15.1 prior to 15.1F2 or 15.1R1, 15.1X49 prior to 15.1X49-D20 where the BGP add-path feature is enabled with 'send' option or with both 'send' and 'receive' options, a network based attacker can cause the Junos OS rpd daemon to crash and restart. Repeated crashes of the rpd daemon can result in an extended denial of service condition.

An Incorrect Behavior Order vulnerability in the MAP-E automatic tunneling mechanism of Juniper Networks Junos OS allows an attacker to send certain malformed IPv4 or IPv6 packets to cause a Denial of Service (DoS) to the PFE on the device which is disabled as a result of the processing of these packets. Continued receipt and processing of these malformed IPv4 or IPv6 packets will create a sustained Denial of Service (DoS) condition. This issue only affects MPC 7/8/9/10/11 cards, when MAP-E IP reassembly is enabled on these cards. An indicator of compromise is the output: FPC ["FPC ID" # e.g. "0"] PFE #{PFE ID # e.g. "1"] : Fabric Disabled Example: FPC 0 PFE #1 : Fabric Disabled when using the command: show chassis fabric fpcs An example of a healthy result of the command use would be: user@device-re1> show chassis fabric fpcs Fabric management FPC state: FPC 0 PFE #0 Plane 0: Plane enabled Plane 1: Plane enabled Plane 2: Plane enabled Plane 3: Plane enabled Plane 4: Plane enabled Plane 5: Plane enabled Plane 6: Plane enabled Plane 7: Plane enabled This issue affects: Juniper Networks Junos OS on MX Series with MPC 7/8/9/10/11 cards, when MAP-E IP reassembly is enabled on these cards. 17.2 version 17.2R1 and later versions; 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S12, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R2-S6, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S1; 18.4 versions prior to 18.4R1-S8, 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S5, 19.3R3. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R1.

An Improper Check for Unusual or Exceptional Conditions vulnerability combined with a Race Condition in the flow daemon (flowd) of Juniper Networks Junos OS on SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2 allows an unauthenticated network based attacker sending specific traffic to cause a crash of the flowd/srxpfe process, responsible for traffic forwarding in SRX, which will cause a Denial of Service (DoS). Continued receipt and processing of this specific traffic will create a sustained Denial of Service (DoS) condition. This issue can only occur when specific packets are trying to create the same session and logging for session-close is configured as a policy action. Affected platforms are: SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2. Not affected platforms are: SRX4000 Series, SRX5000 Series with SPC3, and vSRX Series. This issue affects Juniper Networks Junos OS SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2: All versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2.

In broadband environments, including but not limited to Enhanced Subscriber Management, (CHAP, PPP, DHCP, etc.), on Juniper Networks Junos OS devices where RADIUS servers are configured for managing subscriber access and a subscriber is logged in and then requests to logout, the subscriber may be forced into a "Terminating" state by an attacker who is able to send spoofed messages appearing to originate from trusted RADIUS server(s) destined to the device in response to the subscriber's request. These spoofed messages cause the Junos OS General Authentication Service (authd) daemon to force the broadband subscriber into this "Terminating" state which the subscriber will not recover from thereby causing a Denial of Service (DoS) to the endpoint device. Once in the "Terminating" state, the endpoint subscriber will no longer be able to access the network. Restarting the authd daemon on the Junos OS device will temporarily clear the subscribers out of the "Terminating" state. As long as the attacker continues to send these spoofed packets and subscribers request to be logged out, the subscribers will be returned to the "Terminating" state thereby creating a persistent Denial of Service to the subscriber. An indicator of compromise may be seen by displaying the output of "show subscribers summary". The presence of subscribers in the "Terminating" state may indicate the issue is occurring. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect: Juniper Networks Junos OS 12.3 version 12.3R1 and later versions; 15.1 version 15.1R1 and later versions.

On Juniper Networks Junos OS and Junos OS Evolved devices, processing a specific UPDATE for an EBGP peer can lead to a routing process daemon (RPD) crash and restart. This issue occurs only when the device is receiving and processing the BGP UPDATE for an EBGP peer. This issue does not occur when the device is receiving and processing the BGP UPDATE for an IBGP peer. However, the offending BGP UPDATE can originally come from an EBGP peer, propagates through the network via IBGP peers without causing crash, then it causes RPD crash when it is processed for a BGP UPDATE towards an EBGP peer. Repeated receipt and processing of the same specific BGP UPDATE can result in an extended Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 17.3R3-S6, 17.4R2-S7, and 18.1R3-S7. Juniper Networks Junos OS Evolved 19.2R2-EVO and later versions, prior to 19.3R1-EVO. Other Junos OS releases are not affected.

On Juniper Networks Junos OS devices configured with BGP origin validation using Resource Public Key Infrastructure (RPKI) receipt of a specific packet from the RPKI cache server may cause routing process daemon (RPD) to crash and restart, creating a Denial of Service (DoS) condition. Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R2-S2-EVO.

A Data Processing vulnerability in the Multi-Service process (multi-svcs) on the FPC of Juniper Networks Junos OS on the PTX Series routers may lead to the process becoming unresponsive, ultimately affecting traffic forwarding, allowing an attacker to cause a Denial of Service (DoS) condition . The Multi-Service Process running on the FPC is responsible for handling sampling-related operations when a J-Flow configuration is activated. This can occur during periods of heavy route churn, causing the Multi-Service Process to stop processing updates, without consuming any further updates from kernel. This back pressure towards the kernel affects further dynamic updates from other processes in the system, including RPD, causing a KRT-STUCK condition and traffic forwarding issues. An administrator can monitor the following command to check if there is the KRT queue is stuck: user@device > show krt state ... Number of async queue entries: 65007 <--- this value keep on increasing. The following logs/alarms will be observed when this condition exists: user@junos> show chassis alarms 2 alarms currently active Alarm time Class Description 2020-10-11 04:33:45 PDT Minor Potential slow peers are: MSP(FPC1-PIC0) MSP(FPC3-PIC0) MSP(FPC4-PIC0) Logs: Oct 11 04:33:44.672 2020 test /kernel: rts_peer_cp_recv_timeout : Bit set for msp8 as it is stuck Oct 11 04:35:56.000 2020 test-lab fpc4 user.err gldfpc-multi-svcs.elf: Error in parsing composite nexthop Oct 11 04:35:56.000 2020 test-lab fpc4 user.err gldfpc-multi-svcs.elf: composite nexthop parsing error Oct 11 04:43:05 2020 test /kernel: rt_pfe_veto: Possible slowest client is msp38. States processed - 65865741. States to be processed - 0 Oct 11 04:55:55 2020 test /kernel: rt_pfe_veto: Memory usage of M_RTNEXTHOP type = (0) Max size possible for M_RTNEXTHOP type = (8311787520) Current delayed unref = (60000), Current unique delayed unref = (10896), Max delayed unref on this platform = (40000) Current delayed weight unref = (71426) Max delayed weight unref on this platform= (400000) curproc = rpd Oct 11 04:56:00 2020 test /kernel: rt_pfe_veto: Too many delayed route/nexthop unrefs. Op 2 err 55, rtsm_id 5:-1, msg type 2 This issue only affects PTX Series devices. No other products or platforms are affected by this vulnerability. This issue affects Juniper Networks Junos OS on PTX Series: 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S8, 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S2, 20.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 18.2R1.

A signal handler race condition exists in the Layer 2 Address Learning Daemon (L2ALD) of Juniper Networks Junos OS due to the absence of a specific protection mechanism to avoid a race condition which may allow an attacker to bypass the storm-control feature on devices. This issue is a corner case and only occurs during specific actions taken by an administrator of a device under certain specifics actions which triggers the event. The event occurs less frequently on devices which are not configured with Virtual Chassis configurations, and more frequently on devices configured in Virtual Chassis configurations. This issue is not specific to any particular Junos OS platform. An Indicator of Compromise (IoC) may be seen by reviewing log files for the following error message seen by executing the following show statement: show log messages | grep storm Result to look for: /kernel: GENCFG: op 58 (Storm Control Blob) failed; err 1 (Unknown) This issue affects: Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D49 on EX Series; 15.1 versions prior to 15.1R7-S6; 15.1X49 versions prior to 15.1X49-D191, 15.1X49-D200 on SRX Series; 16.1 versions prior to 16.1R7-S7; 16.2 versions prior to 16.2R2-S11, 16.2R3; 17.1 versions prior to 17.1R2-S11, 17.1R3; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.3 versions prior to 17.3R2-S5, 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S5; 18.2 versions prior to 18.2R2-S6, 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S5, 18.4R2; 19.1 versions prior to 19.1R1-S4, 19.1R2.

A vulnerability in telnetd service on Junos OS allows a remote attacker to cause a limited memory and/or CPU consumption denial of service attack. This issue was found during internal product security testing. Affected releases are Juniper Networks Junos OS 12.1X46 prior to 12.1X46-D45; 12.3X48 prior to 12.3X48-D30; 14.1 prior to 14.1R4-S9, 14.1R8; 14.2 prior to 14.2R6; 15.1 prior to 15.1F5, 15.1R3; 15.1X49 prior to 15.1X49-D40; 15.1X53 prior to 15.1X53-D232, 15.1X53-D47.

An Improper Input Validation vulnerability in the kernel of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). If the receipt of router advertisements is enabled on an interface and a specifically malformed RA packet is received, memory corruption will happen which leads to an rpd crash. This issue affects: Juniper Networks Junos OS 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2. Juniper Networks Junos OS Evolved 20.3-EVO version 20.3R1-EVO and later versions; 20.4-EVO versions prior to 20.4R3-S6-EVO; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R2-EVO; 22.1-EVO versions prior to 22.1R2-EVO.

Open redirect vulnerability in dana/home/homepage.cgi in Juniper Networks IVE 6.5R1 (Build 14599) and 6.5R2 (Build 14951) allows remote attackers to redirect users to arbitrary web sites and conduct phishing attacks via a URL in the Location parameter.

An Improper Input Validation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved allows a local, low-privileged attacker to cause a Denial of Service (DoS). When a specific "clear" command is run, the Advanced Forwarding Toolkit manager (evo-aftmand-bt or evo-aftmand-zx) crashes and restarts. The crash impacts all traffic going through the FPCs, causing a DoS. Running the command repeatedly leads to a sustained DoS condition. This issue affects Junos OS Evolved:  * All versions before 20.4R3-S9-EVO,  * from 21.2-EVO before 21.2R3-S7-EVO,  * from 21.3-EVO before 21.3R3-S5-EVO,  * from 21.4-EVO before 21.4R3-S6-EVO,  * from 22.1-EVO before 22.1R3-S4-EVO,  * from 22.2-EVO before 22.2R3-S3-EVO,  * from 22.3-EVO before 22.3R3-S3-EVO,  * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.