On Juniper Networks Junos OS devices configured with DHCPv6 relay enabled, receipt of a specific DHCPv6 packet might crash the jdhcpd daemon. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. Only DHCPv6 packet can trigger this issue. DHCPv4 packet cannot trigger this issue. This issue affects Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2, 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R2-S2, 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S3, 20.1R2.

When a device running Juniper Networks Junos OS with MPC7, MPC8, or MPC9 line cards installed and the system is configured for inline IP reassembly, used by L2TP, MAP-E, GRE, and IPIP, the packet forwarding engine (PFE) will become disabled upon receipt of large packets requiring fragmentation, generating the following error messages: [LOG: Err] MQSS(0): WO: Packet Error - Error Packets 1, Connection 29 [LOG: Err] eachip_hmcif_rx_intr_handler(7259): EA[0:0]: HMCIF Rx: Injected checksum error detected on WO response - Chunk Address 0x0 [LOG: Err] MQSS(0): DRD: RORD1: CMD reorder ID error - Command 11, Reorder ID 1838, QID 0 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk length error in stage 5 - Chunk Address: 0x4321f3 [LOG: Err] MQSS(0): DRD: UNROLL0: HMC chunk address error in stage 5 - Chunk Address: 0x0 [LOG: Notice] Error: /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc), scope: pfe, category: functional, severity: major, module: MQSS(0), type: DRD_RORD_ENG_INT: CMD FSM State Error [LOG: Notice] Performing action cmalarm for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action get-state for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major [LOG: Notice] Performing action disable-pfe for error /fpc/8/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_DRD_RORD_ENG_INT_REG_CMD_FSM_STATE_ERR (0x2203cc) in module: MQSS(0) with scope: pfe category: functional level: major By continuously sending fragmented packets that cannot be reassembled, an attacker can repeatedly disable the PFE causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS: 17.2 versions prior to 17.2R3-S4 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2 on MX Series; 18.1 versions prior to 18.1R3-S10 on MX Series; 18.2 versions prior to 18.2R3-S3 on MX Series; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D65 on MX Series; 18.3 versions prior to 18.3R1-S7, 18.3R2-S4, 18.3R3-S1 on MX Series; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3 on MX Series; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3 on MX Series; 19.2 versions prior to 19.2R1-S4, 19.2R2 on MX Series; 19.3 versions prior to 19.3R2-S2, 19.3R3 on MX Series. This issue is specific to inline IP reassembly, introduced in Junos OS 17.2. Versions of Junos OS prior to 17.2 are unaffected by this vulnerability.

On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a prolonged Denial of Service. This issue affects MX Series devices using MS-PIC, MS-MIC or MS-MPC service cards with any service configured. This issue affects Juniper Networks Junos OS on MX Series: 17.2R2-S7; 17.3R3-S4, 17.3R3-S5; 17.4R2-S4 and the subsequent SRs (17.4R2-S5, 17.4R2-S6, etc.); 17.4R3; 18.1R3-S3, 18.1R3-S4, 18.1R3-S5, 18.1R3-S6, 18.1R3-S7, 18.1R3-S8; 18.2R3, 18.2R3-S1, 18.2R3-S2; 18.3R2 and the SRs based on 18.3R2; 18.4R2 and the SRs based on 18.4R2; 19.1R1 and the SRs based on 19.1R1; 19.2R1 and the SRs based on 19.2R1; 19.3R1 and the SRs based on 19.3R1.

On High-End SRX Series devices, in specific configurations and when specific networking events or operator actions occur, an SPC receiving genuine multicast traffic may core. Subsequently, all FPCs in a chassis may reset causing a Denial of Service. This issue affects both IPv4 and IPv6. This issue affects: Juniper Networks Junos OS 12.3X48 version 12.3X48-D80 and later versions prior to 12.3X48-D95 on High-End SRX Series. This issue does not affect Branch SRX Series devices.

An Improper Following of Specification by Caller vulnerability in web management (J-Web, Captive Portal, 802.1X, Juniper Secure Connect (JSC) of Juniper Networks Junos OS on SRX Series, EX Series, MX240, MX480, MX960, QFX5120 Series, allows an unauthenticated, network-based attacker, sending genuine traffic targeted to the device to cause the CPU to climb until the device becomes unresponsive. Continuous receipt of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Junos OS:  * All versions before 21.4R3-S9, * from 22.2 before 22.2R3-S5, * from 22.4 before 22.4R3-S4, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S3, * from 24.2 before 24.2R1-S1, 24.2R2. An indicator of compromise is to review the CPU % of the httpd process in the CLI: e.g.   show system processes extensive | match httpd  PID nobody       52   0   20M    191M select   2   0:01   80.00% httpd{httpd} <<<<< the percentage of httpd usage if high may be an indicator

An Improper Check for Unusual or Exceptional Conditions vulnerability in the pfe (packet forwarding engine) of Juniper Networks Junos OS on MX Series causes a port within a pool to be blocked leading to Denial of Service (DoS). In a DS-Lite (Dual-Stack Lite) and NAT (Network Address Translation) scenario, when crafted IPv6 traffic is received and prefix-length is set to 56, the ports assigned to the user will not be freed.  Eventually, users cannot establish new connections. Affected FPC/PIC need to be manually restarted to recover. Following is the command to identify the issue:      user@host> show services nat source port-block      Host_IP                     External_IP                   Port_Block      Ports_Used/       Block_State/                                                               Range           Ports_Total       Left_Time(s)     2001::                        x.x.x.x                     58880-59391     256/256*1         Active/-       >>>>>>>>port still usedThis issue affects Junos OS on MX Series:  * from 21.2 before 21.2R3-S8,  * from 21.4 before 21.4R3-S7,  * from 22.1 before 22.1R3-S6,  * from 22.2 before 22.2R3-S4,  * from 22.3 before 22.3R3-S3,  * from 22.4 before 22.4R3-S2,  * from 23.2 before 23.2R2-S1,  * from 23.4 before 23.4R1-S2, 23.4R2. This issue does not affect versions before 20.2R1.

On Juniper Networks SRX Series configured with application identification inspection enabled, receipt of specific HTTP traffic can cause high CPU load utilization, which could lead to traffic interruption. Application identification is enabled by default and is automatically turned on when Intrusion Detection and Prevention (IDP), AppFW, AppQoS, or AppTrack is configured. Thus, this issue might occur when IDP, AppFW, AppQoS, or AppTrack is configured. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D105; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230; 17.4 versions prior to 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S5, 18.4R3-S1; 19.1 versions prior to 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2.

On Juniper Networks Junos OS and Junos OS Evolved devices, the receipt of a specific BGP UPDATE packet causes an internal counter to be incremented incorrectly, which over time can lead to the routing protocols process (RPD) crash and restart. This issue affects both IBGP and EBGP multihop deployment in IPv4 or IPv6 network. This issue affects: Juniper Networks Junos OS: 17.2X75 versions prior to 17.2X75-D105.19; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S4; 18.2X75 versions prior to 18.2X75-D13, 18.2X75-D411.1, 18.2X75-D420.18, 18.2X75-D52.3, 18.2X75-D60; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS Evolved: any releases prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS releases prior to 17.3R1.

On Juniper Networks MX Series with MS-MIC or MS-MPC card configured with NAT64 configuration, receipt of a malformed IPv6 packet may crash the MS-PIC component on MS-MIC or MS-MPC. This issue occurs when a multiservice card is translating the malformed IPv6 packet to IPv4 packet. An unauthenticated attacker can continuously send crafted IPv6 packets through the device causing repetitive MS-PIC process crashes, resulting in an extended Denial of Service condition. This issue affects Juniper Networks Junos OS on MX Series: 15.1 versions prior to 15.1R7-S7; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S6; 17.4 versions prior to 17.4R2-S11, 17.4R3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D430, 18.2X75-D53, 18.2X75-D65; 18.3 versions prior to 18.3R2-S4, 18.3R3; 18.4 versions prior to 18.4R2-S5, 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2.

An Out-of-bounds Read vulnerability in Juniper Networks Junos OS and Junos OS Evolved's routing protocol daemon (rpd) allows an unauthenticated, network-based attacker to send malformed BGP packets to a device configured with packet receive trace options enabled to crash rpd. This issue affects: Junos OS:  * from 21.2R3-S8 before 21.2R3-S9,  * from 21.4R3-S7 before 21.4R3-S9,  * from 22.2R3-S4 before 22.2R3-S5,  * from 22.3R3-S2 before 22.3R3-S4,  * from 22.4R3 before 22.4R3-S5,  * from 23.2R2 before 23.2R2-S2,  * from 23.4R1 before 23.4R2-S1,  * from 24.2R1 before 24.2R1-S1, 24.2R2. Junos OS Evolved: * from 21.4R3-S7-EVO before 21.4R3-S9-EVO,  * from 22.2R3-S4-EVO before 22.2R3-S5-EVO,  * from 22.3R3-S2-EVO before 22.3R3-S4-EVO,  * from 22.4R3-EVO before 22.4R3-S5-EVO,  * from 23.2R2-EVO before 23.2R2-S2-EVO,  * from 23.4R1-EVO before 23.4R2-S1-EVO,  * from 24.2R1-EVO before 24.2R1-S2-EVO, 24.2R2-EVO. This issue requires a BGP session to be established. This issue can propagate and multiply through multiple ASes until reaching vulnerable devices. This issue affects iBGP and eBGP. This issue affects IPv4 and IPv6. An indicator of compromise may be the presence of malformed update messages in a neighboring AS which is unaffected by this issue: For example, by issuing the command on the neighboring device:  show log messages Reviewing for similar messages from devices within proximity to each other may indicate this malformed packet is propagating:   rpd[<pid>]: Received malformed update from <IP address> (External AS <AS#>) and   rpd[<pid>]: Malformed Attribute

An issue was discovered in Embedthis GoAhead before 4.0.1 and Appweb before 7.0.2. An HTTP POST request with a specially crafted "Host" header field may cause a NULL pointer dereference and thus cause a denial of service, as demonstrated by the lack of a trailing ']' character in an IPv6 address.

An issue was discovered in Embedthis GoAhead before 4.0.1 and Appweb before 7.0.2. The server mishandles some HTTP request fields associated with time, which results in a NULL pointer dereference, as demonstrated by If-Modified-Since or If-Unmodified-Since with a month greater than 11.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series allows a unauthenticated network-based attacker to cause an infinite loop, resulting in a Denial of Service (DoS). An attacker who sends malformed TCP traffic via an interface configured with PPPoE, causes an infinite loop on the respective PFE. This results in consuming all resources and a manual restart is needed to recover. This issue affects interfaces with PPPoE configured and tcp-mss enabled. This issue affects Juniper Networks Junos OS * All versions prior to 20.4R3-S7; * 21.1 version 21.1R1 and later versions; * 21.2 versions prior to 21.2R3-S6; * 21.3 versions prior to 21.3R3-S5; * 21.4 versions prior to 21.4R3-S3; * 22.1 versions prior to 22.1R3-S4; * 22.2 versions prior to 22.2R3; * 22.3 versions prior to 22.3R2-S2; * 22.4 versions prior to 22.4R2;

The receipt of a crafted BGP UPDATE can lead to a routing process daemon (RPD) crash and restart. Repeated receipt of the same crafted BGP UPDATE can result in an extended denial of service condition for the device. This issue only affects the specific versions of Junos OS listed within this advisory. Earlier releases are unaffected by this vulnerability. This crafted BGP UPDATE does not propagate to other BGP peers. Affected releases are Juniper Networks Junos OS: 16.1X65 versions prior to 16.1X65-D47; 17.2X75 versions prior to 17.2X75-D91, 17.2X75-D110; 17.3 versions prior to 17.3R1-S4, 17.3R2; 17.4 versions prior to 17.4R1-S3, 17.4R2.

A vulnerability in the Routing Protocols Daemon (RPD) with Juniper Extension Toolkit (JET) support can allow a network based unauthenticated attacker to cause a severe memory exhaustion condition on the device. This can have an adverse impact on the system performance and availability. This issue only affects devices with JET support running Junos OS 17.2R1 and subsequent releases. Other versions of Junos OS are unaffected by this vulnerability. Affected releases are Juniper Networks Junos OS: 17.2 versions prior to 17.2R1-S7, 17.2R2-S6, 17.2R3; 17.2X75 versions prior to 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R2-S4, 17.3R3; 17.4 versions prior to 17.4R1-S5, 17.4R2; 18.1 versions prior to 18.1R2-S3, 18.1R3;

On Juniper Networks Junos OS and Junos OS Evolved devices processing a specially crafted BGP UPDATE or KEEPALIVE message can lead to a routing process daemon (RPD) crash and restart, causing a Denial of Service (DoS). Continued receipt and processing of this message will create a sustained Denial of Service (DoS) condition. This issue affects both IBGP and EBGP deployments over IPv4 or IPv6. This issue affects: Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R1-S4, 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS Evolved: 20.3 versions prior to 20.3R2-EVO.

A denial of service vulnerability in Juniper Networks NorthStar Controller Application prior to version 2.1.0 Service Pack 1 may allow a malicious attacker crafting packets destined to the device to cause a persistent denial of service to the path computation server service.

A denial of service vulnerability in rpd daemon of Juniper Networks Junos OS allows a malformed MPLS ping packet to crash the rpd daemon if MPLS OAM is configured. Repeated crashes of the rpd daemon can result in an extended denial of service condition for the device. The affected releases are Junos OS 12.3X48 prior to 12.3X48-D50, 12.3X48-D55; 13.3 prior to 13.3R10; 14.1 prior to 14.1R4-S13, 14.1R8-S3, 14.1R9; 14.1X53 prior to 14.1X53-D42, 14.1X53-D50; 14.2 prior to 14.2R4-S8, 14.2R7-S6, 14.2R8; 15.1 prior to 15.1F2-S14, 15.1F5-S7, 15.1F6-S4, 15.1F7, 15.1R4-S7, 15.1R5-S1, 15.1R6; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D105, 15.1X53-D47, 15.1X53-D62, 15.1X53-D70; 16.1 prior to 16.1R3-S3, 16.1R4. No other Juniper Networks products or platforms are affected by this issue.

Receipt of a malformed BGP OPEN message may cause the routing protocol daemon (rpd) process to crash and restart. By continuously sending specially crafted BGP OPEN messages, an attacker can repeatedly crash the rpd process causing prolonged denial of service. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS 12.3 prior to 12.3R12-S4, 12.3R13, 12.3R3-S4; 12.3X48 prior to 12.3X48-D50; 13.3 prior to 13.3R4-S11, 13.3R10; 14.1 prior to 14.1R8-S3, 14.1R9; 14.1X53 prior to 14.1X53-D40; 14.1X55 prior to 14.1X55-D35; 14.2 prior to 14.2R4-S7, 14.2R6-S4, 14.2R7; 15.1 prior to 15.1F2-S11, 15.1F4-S1-J1, 15.1F5-S3, 15.1F6, 15.1R4; 15.1X49 prior to 15.1X49-D100; 15.1X53 prior to 15.1X53-D33, 15.1X53-D50.

A command injection vulnerability in Juniper Networks NorthStar Controller Application prior to version 2.1.0 Service Pack 1 may allow a network-based malicious attacker to cause a denial of service condition.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If specific traffic is received on MX Series and its rate exceeds the respective DDoS protection limit the ingress PFE will crash and restart. Continued receipt of this traffic will create a sustained DoS condition. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S5; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.

A Use of Uninitialized Resource vulnerability in the Border Gateway Protocol (BGP) software of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker to send specific genuine BGP packets to a device configured with BGP to cause a Denial of Service (DoS) by crashing the Routing Protocol Daemon (rpd). This issue is triggered when the packets attempt to initiate a BGP connection before a BGP session is successfully established. Continued receipt of these specific BGP packets will cause a sustained Denial of Service condition. This issue is triggerable in both iBGP and eBGP deployments. This issue affects: Juniper Networks Junos OS 21.1 version 21.1R1 and later versions prior to 21.1R3-S5; 21.2 version 21.2R1 and later versions prior to 21.2R3-S2; 21.3 version 21.3R1 and later versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 21.1R1. This issue affects: Juniper Networks Junos OS Evolved 21.1-EVO version 21.1R1-EVO and later versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.1R1-EVO.

An Improper Validation of Array Index vulnerability in the SIP ALG of Juniper Networks Junos OS on SRX 5000 Series allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). When an attacker sends an SIP packets with a malformed SDP field then the SIP ALG can not process it which will lead to an FPC crash and restart. Continued receipt of these specific packets will lead to a sustained Denial of Service. This issue can only occur when both below mentioned conditions are fulfilled: 1. Call distribution needs to be enabled: [security alg sip enable-call-distribution] 2. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX, and MX with SPC3 use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX 5000 Series: 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R1-S1, 22.3R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1.

A Missing Release of Memory after Effective Lifetime vulnerability in the Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In an IPsec VPN environment, a memory leak will be seen if a DH or ECDH group is configured. Eventually the flowd process will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

An Out-of-Bounds Write vulnerability in Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On SRX Series devices using Unified Policies with IPv6, when a specific IPv6 packet goes through a dynamic-application filter which will generate an ICMP deny message, the flowd core is observed and the PFE is restarted. This issue affects: Juniper Networks Junos OS on SRX Series: 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.

An Improper Handling of Unexpected Data Type vulnerability in the handling of SIP calls in Juniper Networks Junos OS on SRX Series and MX Series platforms allows an attacker to cause a memory leak leading to Denial of Services (DoS). This issue occurs on all MX Series platforms with MS-MPC or MS-MIC card and all SRX Series platforms where SIP ALG is enabled. Successful exploitation of this vulnerability prevents additional SIP calls and applications from succeeding. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.1 versions 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2, 22.1R3-S1. This issue does not affect Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 18.2R1.

An Improper Validation of Array Index vulnerability in the Advanced Forwarding Toolkit Manager daemon (aftmand) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). On the PTX10008 and PTX10016 platforms running Junos OS or Junos OS Evolved, when a specific SNMP MIB is queried this will cause a PFE crash and the FPC will go offline and not automatically recover. A system restart is required to get the affected FPC in an operational state again. This issue affects: Juniper Networks Junos OS 22.1 version 22.1R2 and later versions; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2. Juniper Networks Junos OS Evolved 21.3-EVO version 21.3R3-EVO and later versions; 21.4-EVO version 21.4R1-S2-EVO, 21.4R2-EVO and later versions prior to 21.4R2-S1-EVO; 22.1-EVO version 22.1R2-EVO and later versions prior to 22.1R3-EVO; 22.2-EVO versions prior to 22.2R1-S1-EVO, 22.2R2-EVO.

An Allocation of Resources Without Limits or Throttling vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On QFX10K Series, Inter-Chassis Control Protocol (ICCP) is used in MC-LAG topologies to exchange control information between the devices in the topology. ICCP connection flaps and sync issues will be observed due to excessive specific traffic to the local device. This issue affects Juniper Networks Junos OS on QFX10K Series: * All versions prior to 20.2R3-S7; * 20.4 versions prior to 20.4R3-S4; * 21.1 versions prior to 21.1R3-S3; * 21.2 versions prior to 21.2R3-S1; * 21.3 versions prior to 21.3R3; * 21.4 versions prior to 21.4R3; * 22.1 versions prior to 22.1R2.

A Buffer Overflow vulnerability in SIP ALG of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). On all MX Series and SRX Series platform with SIP ALG enabled, when a malformed SIP packet is received, the flow processing daemon (flowd) will crash and restart. This issue affects: Juniper Networks Junos OS on MX Series and SRX Series 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R1-S1, 22.2R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1 on SRX Series.

When sFlow is enabled and it monitors a packet forwarded via ECMP, a buffer management vulnerability in the dcpfe process of Juniper Networks Junos OS on QFX10K Series systems allows an attacker to cause the Packet Forwarding Engine (PFE) to crash and restart by sending specific genuine packets to the device, resulting in a Denial of Service (DoS) condition. The dcpfe process tries to copy more data into a smaller buffer, which overflows and corrupts the buffer, causing a crash of the dcpfe process. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on QFX10K Series: All versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R1-S2, 22.2R2.

A vulnerability in class-of-service (CoS) queue management in Juniper Networks Junos OS on the ACX2K Series devices allows an unauthenticated network-based attacker to cause a Denial of Service (DoS). Specific packets are being incorrectly routed to a queue used for other high-priority traffic such as BGP, PIM, ICMP, ICMPV6 ND and ISAKMP. Due to this misclassification of traffic, receipt of a high rate of these specific packets will cause delays in the processing of other traffic, leading to a Denial of Service (DoS). Continued receipt of this amount of traffic will create a sustained Denial of Service (DoS) condition. This issue affects Juniper Networks Junos OS on ACX2K Series: All versions prior to 19.4R3-S9; All 20.2 versions; 20.3 versions prior to 20.3R3-S6 on ACX2K Series; 20.4 versions prior to 20.4R3-S4 on ACX2K Series; All 21.1 versions; 21.2 versions prior to 21.2R3-S3 on ACX2K Series. Note: This issues affects legacy ACX2K Series PPC-based devices. This platform reached Last Supported Version (LSV) as of the Junos OS 21.2 Release.

An Uncontrolled Resource Consumption vulnerability in TCP processing on the Routing Engine (RE) of Juniper Networks Junos OS allows an unauthenticated network-based attacker to send crafted TCP packets destined to the device, resulting in an MBUF leak that ultimately leads to a Denial of Service (DoS). The system does not recover automatically and must be manually restarted to restore service. This issue occurs when crafted TCP packets are sent directly to a configured IPv4 or IPv6 interface on the device. Transit traffic will not trigger this issue. MBUF usage can be monitored through the use of the 'show system buffers' command. For example: user@junos> show system buffers | refresh 5 4054/566/4620 mbufs in use (current/cache/total) ... 4089/531/4620 mbufs in use (current/cache/total) ... 4151/589/4740 mbufs in use (current/cache/total) ... 4213/527/4740 mbufs in use (current/cache/total) This issue affects Juniper Networks Junos OS: 12.3 version 12.3R12-S19 and later versions; 15.1 version 15.1R7-S10 and later versions; 17.3 version 17.3R3-S12 and later versions; 18.4 version 18.4R3-S9 and later versions; 19.1 version 19.1R3-S7 and later versions; 19.2 version 19.2R3-S3 and later versions; 19.3 version 19.3R2-S7, 19.3R3-S3 and later versions prior to 19.3R3-S7; 19.4 version 19.4R2-S7, 19.4R3-S5 and later versions prior to 19.4R3-S10; 20.1 version 20.1R3-S1 and later versions; 20.2 version 20.2R3-S2 and later versions prior to 20.2R3-S6; 20.3 version 20.3R3-S1 and later versions prior to 20.3R3-S6; 20.4 version 20.4R2-S2, 20.4R3 and later versions prior to 20.4R3-S5; 21.1 version 21.1R2 and later versions prior to 21.1R3-S4; 21.2 version 21.2R1-S1, 21.2R2 and later versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2-S1, 22.1R3; 22.2 versions prior to 22.2R1-S2, 22.2R2; 22.3 versions prior to 22.3R1-S1, 22.3R2.

An Improper Check or Handling of Exceptional Conditions vulnerability in the IPsec library of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause Denial of Service (DoS). On all MX platforms with MS-MPC or MS-MIC card, when specific IPv4 packets are processed by an IPsec6 tunnel, the Multiservices PIC Management Daemon (mspmand) process will core and restart. This will lead to FPC crash. Traffic flow is impacted while mspmand restarts. Continued receipt of these specific packets will cause a sustained Denial of Service (DoS) condition. This issue only occurs if an IPv4 address is not configured on the multiservice interface. This issue affects: Juniper Networks Junos OS on MX Series All versions prior to 19.4R3-S9; 20.1 version 20.1R3-S5 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2.

An Improper Validation of Specified Type of Input vulnerability in the packet forwarding engine (pfe) Juniper Networks Junos OS on SRX5000 Series allows an unauthenticated, network based attacker to cause a Denial of Service (Dos). When a non-clustered SRX5000 device receives a specifically malformed packet this will cause a flowd crash and restart. This issue affects Junos OS: * 22.1 releases 22.1R1 and later before 22.2R3-S5, * 22.3 releases before 22.3R3-S4, * 22.4 releases before 22.4R3-S4, * 23.2 releases before 23.2R2-S2, * 23.4 releases before 23.4R2-S1, * 24.2 releases before 24.2R1-S1, 24.2R2. Please note that the PR does indicate that earlier versions have been fixed as well, but these won't be adversely impacted by this.

Receipt of a malformed packet on MX Series devices with dynamic vlan configuration can trigger an uncontrolled recursion loop in the Broadband Edge subscriber management daemon (bbe-smgd), and lead to high CPU usage and a crash of the bbe-smgd service. Repeated receipt of the same packet can result in an extended denial of service condition for the device. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S1; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S10, 17.1R3; 17.2 versions prior to 17.2R3; 17.3 versions prior to 17.3R3-S1; 17.4 versions prior to 17.4R2; 18.1 versions prior to 18.1R3; 18.2 versions prior to 18.2R2.

The srxpfe process may crash on SRX Series services gateways when the UTM module processes a specific fragmented HTTP packet. The packet is misinterpreted as a regular TCP packet which causes the processor to crash. This issue affects all SRX Series platforms that support URL-Filtering and have web-filtering enabled. Affected releases are Juniper Networks Junos OS: 12.3X48 versions prior to 12.3X48-D85 on SRX Series; 15.1X49 versions prior to 15.1X49-D181, 15.1X49-D190 on SRX Series; 17.3 versions on SRX Series; 17.4 versions prior to 17.4R1-S8, 17.4R2-S5, 17.4R3 on SRX Series; 18.1 versions prior to 18.1R3-S6 on SRX Series; 18.2 versions prior to 18.2R2-S1, 18.2R3 on SRX Series; 18.3 versions prior to 18.3R1-S2, 18.3R2 on SRX Series; 18.4 versions prior to 18.4R1-S1, 18.4R2 on SRX Series.

An Out-of-Bounds Read vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker sending a specifically malformed BGP packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems configured in either of two ways: * systems with BGP traceoptions enabled * systems with BGP traffic engineering configured This issue can affect iBGP and eBGP with any address family configured. The specific attribute involved is non-transitive, and will not propagate across a network. This issue affects: Junos OS:  * All versions before 21.4R3-S8, * 22.2 before 22.2R3-S5,  * 22.3 before 22.3R3-S4,  * 22.4 before 22.4R3-S3,  * 23.2 before 23.2R2-S2,  * 23.4 before 23.4R2;  Junos OS Evolved:  * All versions before 21.4R3-S8-EVO,  * 22.2-EVO before 22.2R3-S5-EVO,  * 22.3-EVO before 22.3R3-S4-EVO,  * 22.4-EVO before 22.4R3-S3-EVO,  * 23.2-EVO before 23.2R2-S2-EVO,  * 23.4-EVO before 23.4R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker sending a specific BGP packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects systems with BGP traceoptions enabled and requires a BGP session to be already established.  Systems without BGP traceoptions enabled are not affected by this issue. This issue affects iBGP and eBGP, and both IPv4 and IPv6 are affected by this vulnerability. This issue affects: Junos OS:  * All versions before 21.2R3-S8,  * from 21.4 before 21.4R3-S8,  * from 22.2 before 22.2R3-S4,  * from 22.3 before 22.3R3-S4, * from 22.4 before 22.4R3-S3,  * from 23.2 before 23.2R2-S1,  * from 23.4 before 23.4R2;  Junos OS Evolved:  * All versions before 21.2R3-S8-EVO,  * from 21.4-EVO before 21.4R3-S8-EVO,  * from 22.2-EVO before 22.2R3-S4-EVO,  * from 22.3-EVO before 22.3R3-S4-EVO, * from 22.4-EVO before 22.4R3-S3-EVO,  * from 23.2-EVO before 23.2R2-S1-EVO,  * from 23.4-EVO before 23.4R2-EVO.

When an MX Series Broadband Remote Access Server (BRAS) is configured as a Broadband Network Gateway (BNG) with DHCPv6 enabled, jdhcpd might crash when receiving a specific crafted DHCP response message on a subscriber interface. The daemon automatically restarts without intervention, but continuous receipt of specific crafted DHCP messages will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue only affects systems configured with DHCPv6 enabled. DHCPv4 is unaffected by this issue. This issue affects Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S5 on MX Series; 16.1 versions prior to 16.1R7-S5 on MX Series; 16.2 versions prior to 16.2R2-S10 on MX Series; 17.1 versions prior to 17.1R3-S1 on MX Series; 17.2 versions prior to 17.2R3-S2 on MX Series; 17.3 versions prior to 17.3R3-S6 on MX Series; 17.4 versions prior to 17.4R2-S5, 17.4R3 on MX Series; 18.1 versions prior to 18.1R3-S6 on MX Series; 18.2 versions prior to 18.2R2-S4, 18.2R3 on MX Series; 18.2X75 versions prior to 18.2X75-D50 on MX Series; 18.3 versions prior to 18.3R1-S5, 18.3R3 on MX Series; 18.4 versions prior to 18.4R2 on MX Series; 19.1 versions prior to 19.1R1-S2, 19.1R2 on MX Series.

A Missing Release of Resource after Effective Lifetime vulnerability the xinetd process, responsible for spawning SSH daemon (sshd) instances, of Juniper Networks Junos OS Evolved allows an unauthenticated network-based attacker to cause a Denial of Service (DoS) by blocking SSH access for legitimate users. Continued receipt of these connections will create a sustained Denial of Service (DoS) condition. The issue is triggered when a high rate of concurrent SSH requests are received and terminated in a specific way, causing xinetd to crash, and leaving defunct sshd processes. Successful exploitation of this vulnerability blocks both SSH access as well as services which rely upon SSH, such as SFTP, and Netconf over SSH. Once the system is in this state, legitimate users will be unable to SSH to the device until service is manually restored.  See WORKAROUND section below. Administrators can monitor an increase in defunct sshd processes by utilizing the CLI command:   > show system processes | match sshd   root   25219 30901 0 Jul16 ?       00:00:00 [sshd] <defunct> This issue affects Juniper Networks Junos OS Evolved: * All versions prior to 21.4R3-S7-EVO * 22.3-EVO versions prior to 22.3R2-S2-EVO, 22.3R3-S2-EVO; * 22.4-EVO versions prior to 22.4R3-EVO; * 23.2-EVO versions prior to 23.2R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved 22.1-EVO nor 22.2-EVO.

An Improper Validation of Consistency within Input vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated network-based attacker sending a specifically malformed BGP packet to cause rpd to crash and restart, resulting in a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. In some cases, rpd fails to restart requiring a manual restart via the 'restart routing' CLI command. This issue only affects systems with BGP traceoptions enabled and requires a BGP session to be already established. Systems without BGP traceoptions enabled are not affected by this issue. This issue affects iBGP and eBGP, and both IPv4 and IPv6 are affected by this vulnerability. This issue affects: Junos OS:  * All versions before 21.4R3-S8,  * 22.2 before 22.2R3-S5,  * 22.3 before 22.3R3-S4,  * 22.4 before 22.4R3-S3,  * 23.2 before 23.2R2-S2,  * 23.4 before 23.4R2;  Junos OS Evolved:  * All versions before 21.4R3-S8-EVO,  * 22.2-EVO before 22.2R3-S5-EVO,  * 22.3-EVO before 22.3R3-S4-EVO,  * 22.4-EVO before 22.4R3-S3-EVO,  * 23.2-EVO before 23.2R2-S2-EVO,  * 23.4-EVO before 23.4R2-EVO.

An Improper Handling of Exceptional Conditions vulnerability in the rpd-server of Juniper Networks Junos OS and Junos OS Evolved within cRPD allows an unauthenticated network-based attacker sending crafted TCP traffic to the routing engine (RE) to cause a CPU-based Denial of Service (DoS). If specially crafted TCP traffic is received by the control plane, or a TCP session terminates unexpectedly, it will cause increased control plane CPU utilization by the rpd-server process. While not explicitly required, the impact is more severe when RIB sharding is enabled. Task accounting shows unexpected reads by the RPD Server jobs for shards: user@junos> show task accounting detail ... read:RPD Server.0.0.0.0+780.192.168.0.78+48886 TOT:00000003.00379787 MAX:00000000.00080516 RUNS: 233888\ read:RPD Server.0.0.0.0+780.192.168.0.78+49144 TOT:00000004.00007565 MAX:00000000.00080360 RUNS: 233888\ read:RPD Server.0.0.0.0+780.192.168.0.78+49694 TOT:00000003.00600584 MAX:00000000.00080463 RUNS: 233888\ read:RPD Server.0.0.0.0+780.192.168.0.78+50246 TOT:00000004.00346998 MAX:00000000.00080338 RUNS: 233888\ This issue affects: Junos OS with cRPD:  * All versions before 21.2R3-S8,  * 21.4 before 21.4R3-S7,  * 22.1 before 22.1R3-S6,  * 22.2 before 22.2R3-S4,  * 22.3 before 22.3R3-S3,  * 22.4 before 22.4R3-S2,  * 23.2 before 23.2R2-S2,  * 24.2 before 24.2R2;  Junos OS Evolved with cRPD:  * All versions before 21.4R3-S7-EVO,  * 22.2 before 22.2R3-S4-EVO,  * 22.3 before 22.3R3-S3-EVO,  * 22.4 before 22.4R3-S2-EVO,  * 23.2 before 23.2R2-EVO.

An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that an irq handled by the fman process is shown to be using a high percentage of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 31 root -84 -187 0K 16K WAIT 22.2H 56939.26% irq96: fman0 This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S2, 20.4R3; 21.1 versions prior to 21.1R2; 21.2 versions prior to 21.2R1-S1, 21.2R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the Public Key Infrastructure daemon (pkid) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause Denial of Service (DoS). In a scenario where Public Key Infrastructure (PKI) is used in combination with Certificate Revocation List (CRL), if the CRL fails to download the memory allocated to store the CRL is not released. Repeated occurrences will eventually consume all available memory and lead to an inoperable state of the affected system causing a DoS. This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue can be observed by monitoring the memory utilization of the pkid process via: root@jtac-srx1500-r2003> show system processes extensive | match pki 20931 root 20 0 733M 14352K select 0:00 0.00% pkid which increases over time: root@jtac-srx1500-r2003> show system processes extensive | match pki 22587 root 20 0 901M 181M select 0:03 0.00% pkid