Z-Wave devices based on Silicon Labs 500 series chipsets using S2, including but likely not limited to the ZooZ ZST10 version 6.04, ZooZ ZEN20 version 5.03, ZooZ ZEN25 version 5.03, Aeon Labs ZW090-A version 3.95, and Fibaro FGWPB-111 version 4.3, are susceptible to denial of service and resource exhaustion via malformed SECURITY NONCE GET, SECURITY NONCE GET 2, NO OPERATION, or NIF REQUEST messages.

A memory leak in the EFR32 Bluetooth LE stack 5.1.0 through 5.1.1 allows an attacker to send an invalid pairing message and cause future legitimate connection attempts to fail. A reset of the device immediately clears the error.

The Bluetooth Classic implementation in Silicon Labs iWRAP 6.3.0 and earlier does not properly handle the reception of an oversized LMP packet greater than 17 bytes, allowing attackers in radio range to trigger a crash in WT32i via a crafted LMP packet.

Silicon Labs Bluetooth Low Energy SDK before 2.13.3 has a buffer overflow via packet data. This is an over-the-air denial of service vulnerability in Bluetooth LE in EFR32 SoCs and associated modules running Bluetooth SDK, supporting Central or Observer roles.

Z-Wave devices using Silicon Labs 500 and 700 series chipsets, including but not likely limited to the SiLabs UZB-7 version 7.00, ZooZ ZST10 version 6.04, Aeon Labs ZW090-A version 3.95, and Samsung STH-ETH-200 version 6.04, are susceptible to denial of service via malformed routing messages.

Z-Wave devices based on Silicon Labs 700 series chipsets using S2 do not adequately authenticate or encrypt FIND_NODE_IN_RANGE frames, allowing a remote, unauthenticated attacker to inject a FIND_NODE_IN_RANGE frame with an invalid random payload, denying service by blocking the processing of upcoming events.

Insecure permissions in Silicon Labs (SiLabs) Z-Wave Series 700 and 800 v7.21.1 allow attackers to cause disrupt communications between the controller and the device itself via repeatedly sending crafted packets to the controller.

In a Silicon Labs  multi-protocol gateway, a corrupt pointer to buffered data on a multi-protocol radio co-processor (RCP) causes the OpenThread Border Router(OTBR) application task running on the host platform to crash, allowing an attacker to cause a temporary denial-of-service.

An issue was discovered on Sigma Design Z-Wave S0 through S2 devices. An attacker first prepares a Z-Wave frame-transmission program (e.g., Z-Wave PC Controller, OpenZWave, CC1110, etc.). Next, the attacker conducts a DoS attack against the Z-Wave S0 Security version product by continuously sending divided "Nonce Get (0x98 0x81)" frames. The reason for dividing the "Nonce Get" frame is that, in security version S0, when a node receives a "Nonce Get" frame, the node produces a random new nonce and sends it to the Src node of the received "Nonce Get" frame. After the nonce value is generated and transmitted, the node transitions to wait mode. At this time, when "Nonce Get" is received again, the node discards the previous nonce value and generates a random nonce again. Therefore, because the frame is encrypted with previous nonce value, the received normal frame cannot be decrypted.

A truncated 802.15.4 packet can lead to an assert, resulting in a denial of service.

A memory leak in the Silicon Labs' Bluetooth stack for EFR32 products may cause memory to be exhausted when sending notifications to multiple clients, this results in all Bluetooth operations, such as advertising and scanning, to stop.

Malformed S2 Nonce Get Command Class packets can be sent to crash PC Controller v5.54.0 and earlier.

Malformed Device Reset Locally Command Class packets can be sent to the controller, causing the controller to assume the end device has left the network. After this, frames sent by the end device will not be acknowledged by the controller. This vulnerability exists in PC Controller v5.54.0, and earlier.

A denial of service vulnerability exists in all Silicon Labs Z-Wave controller and endpoint devices running Z-Wave SDK v7.20.3 (Gecko SDK v4.3.3) and earlier. This attack can be carried out only by devices on the network sending a stream of packets to the device.

Forcing the Bluetooth LE stack to segment 'prepare write response' packets can lead to an out-of-bounds memory access.

An invalid ‘prepare write request’ command can cause the Bluetooth LE stack to run out of memory and fail to be able to handle subsequent connection requests, resulting in a denial-of-service.

Improper Restriction of Operations within the Bounds of a Memory Buffer vulnerability in Silicon Labs Ember ZNet allows Overflow Buffers.

A malformed packet causes a stack overflow in the Ember ZNet stack. This causes an assert which leads to a reset, immediately clearing the error.

 A malformed packet containing an invalid destination address, causes a stack overflow in the Ember ZNet stack. This causes an assert which leads to a reset, immediately clearing the error.

Denial of Service (DoS) in the Z-Wave S0 NonceGet protocol specification in Silicon Labs Z-Wave 500 series allows local attackers to block S0/S2 protected Z-Wave network via crafted S0 NonceGet Z-Wave packages, utilizing included but absent NodeIDs.

Insecure permissions in Silicon Labs (SiLabs) Z-Wave Series 700 and 800 v7.21.1 allow attackers to change the wakeup interval of end devices in controller memory, disrupting the device's communications with the controller.

Insecure permissions in Silicon Labs (SiLabs) Z-Wave Series 700 and 800 v7.21.1 allow attackers to cause a Denial of Service (DoS) via repeatedly sending crafted packets to the controller.

Due to an allocation of resources without limits, an uncontrolled resource consumption vulnerability exists in Silicon Labs Ember ZNet SDK prior to v7.4.0.0 (delivered as part of Silicon Labs Gecko SDK v4.4.0) which may enable attackers to trigger a bus fault and crash of the device, requiring a reboot in order to rejoin the network.

totolink EX300_v2, ver V4.0.3c.140_B20210429 and A720R ,ver V4.1.5cu.470_B20200911 have an issue which causes uncontrolled resource consumption.

BlueZ is a Bluetooth protocol stack for Linux. In affected versions a vulnerability exists in sdp_cstate_alloc_buf which allocates memory which will always be hung in the singly linked list of cstates and will not be freed. This will cause a memory leak over time. The data can be a very large object, which can be caused by an attacker continuously sending sdp packets and this may cause the service of the target device to crash.

On Juniper Networks EX4300 Series, receipt of a stream of specific IPv4 packets can cause Routing Engine (RE) high CPU load, which could lead to network protocol operation issue and traffic interruption. This specific packets can originate only from within the broadcast domain where the device is connected. This issue occurs when the packets enter to the IRB interface. Only IPv4 packets can trigger this issue. IPv6 packets cannot trigger this issue. This issue affects Juniper Networks Junos OS on EX4300 series: 17.3 versions prior to 17.3R3-S9; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R2-S2, 19.1R3-S1; 19.2 versions prior to 19.2R1-S5, 19.2R2-S1, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S3, 20.1R2.

On Juniper Networks EX2300 Series, receipt of a stream of specific multicast packets by the layer2 interface can cause high CPU load, which could lead to traffic interruption. This issue occurs when multicast packets are received by the layer 2 interface. To check if the device has high CPU load due to this issue, the administrator can issue the following command: user@host> show chassis routing-engine Routing Engine status: ... Idle 2 percent the "Idle" value shows as low (2 % in the example above), and also the following command: user@host> show system processes summary ... PID USERNAME PRI NICE SIZE RES STATE TIME WCPU COMMAND 11639 root 52 0 283M 11296K select 12:15 44.97% eventd 11803 root 81 0 719M 239M RUN 251:12 31.98% fxpc{fxpc} the eventd and the fxpc processes might use higher WCPU percentage (respectively 44.97% and 31.98% in the above example). This issue affects Juniper Networks Junos OS on EX2300 Series: 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S5; 18.3 versions prior to 18.3R2-S4, 18.3R3-S3; 18.4 versions prior to 18.4R2-S5, 18.4R3-S4; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R1-S5, 19.2R3; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2-S1, 19.4R3; 20.1 versions prior to 20.1R1-S2, 20.1R2.

An Uncontrolled Resource Consumption vulnerability in Juniper Networks Junos OS on EX2300, EX3400 and EX4300 Series platforms allows an adjacent attacker sending a stream of layer 2 frames will trigger an Aggregated Ethernet (AE) interface to go down and thereby causing a Denial of Service (DoS). By continuously sending a stream of specific layer 2 frames an attacker will sustain the Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS EX4300 Series All versions prior to 15.1R7-S7; 16.1 versions prior to 16.1R7-S8; 17.1 versions prior to 17.1R2-S12; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S10, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S2, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Juniper Networks Junos OS EX3400 and EX4300-MP Series All versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R2-S9, 18.4R3-S7; 19.1 versions prior to 19.1R2-S3, 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3-S1; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2. Juniper Networks Junos OS EX2300 Series All versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.1 versions prior to 19.1R2-S3, 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S7, 19.3R3-S3; 19.4 versions prior to 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R2.

Improper validation of LLM utility timers availability can lead to denial of service in Snapdragon Auto, Snapdragon Compute, Snapdragon Connectivity, Snapdragon Consumer Electronics Connectivity, Snapdragon Consumer IOT, Snapdragon Industrial IOT, Snapdragon Mobile, Snapdragon Voice & Music

Multiple vulnerabilities in the implementation of the Cisco Discovery Protocol and Link Layer Discovery Protocol (LLDP) for Cisco Video Surveillance 7000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. These vulnerabilities are due to incorrect processing of certain Cisco Discovery Protocol and LLDP packets at ingress time. An attacker could exploit these vulnerabilities by sending crafted Cisco Discovery Protocol or LLDP packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DoS condition. Note: Cisco Discovery Protocol and LLDP are Layer 2 protocols. To exploit these vulnerabilities, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

A vulnerability due to the improper handling of direct memory access (DMA) buffers on EX4300 switches on Juniper Networks Junos OS allows an attacker sending specific unicast frames to trigger a Denial of Service (DoS) condition by exhausting DMA buffers, causing the FPC to crash and the device to restart. The DMA buffer leak is seen when receiving these specific, valid unicast frames on an interface without Layer 2 Protocol Tunneling (L2PT) or dot1x configured. Interfaces with either L2PT or dot1x configured are not vulnerable to this issue. When this issue occurs, DMA buffer usage keeps increasing and the following error log messages may be observed: Apr 14 14:29:34.360 /kernel: pid 64476 (pfex_junos), uid 0: exited on signal 11 (core dumped) Apr 14 14:29:33.790 init: pfe-manager (PID 64476) terminated by signal number 11. Core dumped! The DMA buffers on the FPC can be monitored by the executing vty command 'show heap': ID Base Total(b) Free(b) Used(b) % Name -- ---------- ----------- ----------- ----------- --- ----------- 0 4a46000 268435456 238230496 30204960 11 Kernel 1 18a46000 67108864 17618536 49490328 73 Bcm_sdk 2 23737000 117440512 18414552 99025960 84 DMA buf <<<<< keeps increasing 3 2a737000 16777216 16777216 0 0 DMA desc This issue affects Juniper Networks Junos OS on the EX4300: 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2.

On Juniper Networks MX Series and EX9200 Series platforms with Trio-based MPCs (Modular Port Concentrators) where Integrated Routing and Bridging (IRB) interfaces are configured and mapped to a VPLS instance or a Bridge-Domain, certain Layer 2 network events at Customer Edge (CE) devices may cause memory leaks in the MPC of Provider Edge (PE) devices which can cause an out of memory condition and MPC restart. When this issue occurs, there will be temporary traffic interruption until the MPC is restored. An administrator can use the following CLI command to monitor the status of memory usage level of the MPC: user@device> show system resource-monitor fpc FPC Resource Usage Summary Free Heap Mem Watermark : 20 % Free NH Mem Watermark : 20 % Free Filter Mem Watermark : 20 % * - Watermark reached Slot # % Heap Free RTT Average RTT 1 87 PFE # % ENCAP mem Free % NH mem Free % FW mem Free 0 NA 88 99 1 NA 89 99 When the issue is occurring, the value of “% NH mem Free” will go down until the MPC restarts. This issue affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines), including MX-MPC1-3D, MX-MPC1E-3D, MX-MPC2-3D, MX-MPC2E-3D, MPC-3D-16XGE, and CHAS-MXxx Series MPCs. No other products or platforms are affected by this issue. This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S3; 18.2 versions prior to 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S2, 19.4R3; 20.2 versions prior to 20.2R1-S3, 20.2R2; 20.3 versions prior to 20.3R1-S1,, 20.3R2. This issue does not affect Juniper Networks Junos OS: 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R3-S2; 18.1; 18.2 versions prior to 18.2R3-S4; 18.3 versions prior to 18.3R3-S2; 18.4 versions prior to 18.4R3-S1; 19.1; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R2.

On Juniper Networks Junos EX series, QFX Series, MX Series and SRX branch series devices, a memory leak occurs every time the 802.1X authenticator port interface flaps which can lead to other processes, such as the pfex process, responsible for packet forwarding, to crash and restart. An administrator can use the following CLI command to monitor the status of memory consumption: user@device> show task memory detail Please refer to https://kb.juniper.net/KB31522 for details. This issue affects Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D54; 15.1X49 versions prior to 15.1X49-D240 ; 15.1X53 versions prior to 15.1X53-D593; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10 ; 18.2 versions prior to 18.2R2-S7, 18.2R3-S3; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S2; 19.1 versions prior to 19.1R1-S5, 19.1R2-S2, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. This issue does not affect Juniper Networks Junos OS 12.3, 15.1.

An Uncontrolled Resource Consumption vulnerability in the ARP daemon (arpd) and Network Discovery Protocol (ndp) process of Juniper Networks Junos OS Evolved allows a malicious attacker on the local network to consume memory resources, ultimately resulting in a Denial of Service (DoS) condition. Link-layer functions such as IPv4 and/or IPv6 address resolution may be impacted, leading to traffic loss. The processes do not recover on their own and must be manually restarted. Changes in memory usage can be monitored using the following shell commands (header shown for clarity): user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 59.0 0.7 *5702564* 247952 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 user@router:/var/log# ps aux | grep arpd USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 31418 49.1 1.0 *5813156* 351184 ? xxx /usr/sbin/arpd --app-name arpd -I object_select --shared-objects-mode 3 Memory usage can be monitored for the ndp process in a similar fashion: user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5614052* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje user@router:/var/log# ps aux | grep ndp USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 14935 0.0 0.1 *5725164* 27256 ? Ssl Jun15 0:17 /usr/sbin/ndp -I no_tab_chk,object_select --app-name ndp --shared-obje This issue affects Juniper Networks Junos OS Evolved: 19.4 versions prior to 19.4R2-S3-EVO; 20.1 versions prior to 20.1R2-S4-EVO; all versions of 20.2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 19.4R2-EVO.

The Kubelet component in versions 1.15.0-1.15.9, 1.16.0-1.16.6, and 1.17.0-1.17.2 has been found to be vulnerable to a denial of service attack via the kubelet API, including the unauthenticated HTTP read-only API typically served on port 10255, and the authenticated HTTPS API typically served on port 10250.

Citrix ADC and Citrix/NetScaler Gateway 13.0 before 13.0-76.29, 12.1-61.18, 11.1-65.20, Citrix ADC 12.1-FIPS before 12.1-55.238, and Citrix SD-WAN WANOP Edition before 11.4.0, 11.3.2, 11.3.1a, 11.2.3a, 11.1.2c, 10.2.9a suffers from uncontrolled resource consumption by way of a network-based denial-of-service from within the same Layer 2 network segment. Note that the attacker must be in the same Layer 2 network segment as the vulnerable appliance.

The kernel memory usage represented as "temp" via 'show system virtual-memory' may constantly increase when Integrated Routing and Bridging (IRB) is configured with multiple underlay physical interfaces, and one interface flaps. This memory leak can affect running daemons (processes), leading to an extended Denial of Service (DoS) condition. Usage of "temp" virtual memory, shown here by a constantly increasing value of outstanding Requests, can be monitored by executing the 'show system virtual-memory' command as shown below: user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 10551 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6460 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 16101 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6665 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 user@junos> show system virtual-memory |match "fpc|type|temp" fpc0: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2023 431K - 21867 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 fpc1: -------------------------------------------------------------------------- Type InUse MemUse HighUse Requests Size(s) temp 2020 431K - 6858 16,32,64,128,256,512,1024,2048,4096,65536,262144,1048576,2097152,4194304,8388608 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S6; 17.1 versions prior to 17.1R2-S11, 17.1R3-S1; 17.2 versions prior to 17.2R2-S8, 17.2R3-S3; 17.2X75 versions prior to 17.2X75-D44; 17.3 versions prior to 17.3R2-S5, 17.3R3-S6; 17.4 versions prior to 17.4R2-S5, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R2-S5, 18.2R3; 18.2X75 versions prior to 18.2X75-D33, 18.2X75-D411, 18.2X75-D420, 18.2X75-D60; 18.3 versions prior to 18.3R1-S5, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R2-S2, 18.4R3; 19.1 versions prior to 19.1R1-S3, 19.1R2; 19.2 versions prior to 19.2R1-S3, 19.2R2. This issue does not affect Juniper Networks Junos OS 12.3 and 15.1.

An Uncontrolled Resource Consumption vulnerability in the Connectivity Fault Management (CFM) daemon and the Connectivity Fault Management Manager (cfmman) of Juniper Networks Junos OS Evolved on PTX10001-36MR, PTX10002-36QDD, PTX10004, PTX10008, PTX10016 allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). An attacker on an adjacent device sending specific valid traffic can cause cfmd to spike the CPU to 100% and cfmman's memory to leak, eventually to cause the FPC crash and restart. Continued receipt and processes of these specific valid packets will sustain the Denial of Service (DoS) condition. An indicator of compromise is to watch for an increase in cfmman memory rising over time by issuing the following command and evaluating the RSS number. If the RSS is growing into GBs then consider restarting the device to temporarily clear memory.   user@device> show system processes node fpc<num> detail | match cfmman Example:    show system processes node fpc0 detail | match cfmman    F S UID       PID       PPID PGID   SID   C PRI NI  ADDR SZ    WCHAN   RSS     PSR STIME TTY         TIME     CMD   4 S root      15204     1    15204  15204 0 80  0   - 90802     -      113652   4  Sep25 ?           00:15:28 /usr/bin/cfmman -p /var/pfe -o -c /usr/conf/cfmman-cfg-active.xml This issue affects Junos OS Evolved on PTX10001-36MR, PTX10002-36QDD, PTX10004, PTX10008, PTX10016: * from 23.2R1-EVO before 23.2R2-S4-EVO, * from 23.4 before 23.4R2-S4-EVO, * from 24.2 before 24.2R2-EVO, * from 24.4 before 24.4R1-S2-EVO, 24.4R2-EVO. This issue does not affect Junos OS Evolved on PTX10001-36MR, PTX10002-36QDD, PTX10004, PTX10008, PTX10016 before 23.2R1-EVO.

A denial-of-service vulnerability was reported in some Lenovo printers that could allow an unauthenticated attacker on a shared network to deny printer connections until the system is rebooted.

IBM WebSphere Extreme Scale 8.6.1.0 through 8.6.1.6 could allow an adjacent attacker to cause a denial of service due to improper validation in the XDF decoder. The application processes deeply nested Protocol Buffers messages and attacker-controlled length prefixes without sufficient bounds checking, which may allow an attacker on the same network to trigger a StackOverflowError or OutOfMemoryError, resulting in a crash of the WebSphere Application Server JVM.

The pairing API request handler in Microsoft HoloLens 1 (Windows Holographic) through 10.0.17763.3046 and HoloLens 2 (Windows Holographic) through 10.0.22621.1244 allows remote attackers to cause a Denial of Service (resource consumption and device unusability) by sending many requests through the Device Portal framework.

A prototype pollution in the lib.createUploader function of @rpldy/uploader v1.8.1 allows attackers to cause a Denial of Service (DoS) via supplying a crafted payload.

Successful exploitation of the vulnerability could allow an attacker to cause repeated reboots, potentially leading to remote denial-of-service and system unavailability.

An issue in the Bluetooth Low Energy (BLE) stack of Realtek RTL8762E BLE SDK v1.4.0 allows attackers within Bluetooth range to cause a Denial of Service (DoS) via sending a specific sequence of crafted control packets.

Vulnerability in the TimesTen In-Memory Database product of Oracle TimesTen In-Memory Database (component: ttcserver). The supported version that is affected is 26.1.1.1.0. Easily exploitable vulnerability allows unauthenticated attacker with access to the physical communication segment attached to the hardware where the TimesTen In-Memory Database executes to compromise TimesTen In-Memory Database. Successful attacks of this vulnerability can result in unauthorized ability to cause a hang or frequently repeatable crash (complete DOS) of TimesTen In-Memory Database. CVSS 3.1 Base Score 6.5 (Availability impacts). CVSS Vector: (CVSS:3.1/AV:A/AC:L/PR:N/UI:N/S:U/C:N/I:N/A:H).

A vulnerability in the Cisco Discovery Protocol of Cisco Video Surveillance 8000 Series IP Cameras could allow an unauthenticated, adjacent attacker to cause a memory leak, which could lead to a denial of service (DoS) condition on an affected device. The vulnerability is due to incorrect processing of certain Cisco Discovery Protocol packets. An attacker could exploit this vulnerability by sending certain Cisco Discovery Protocol packets to an affected device. A successful exploit could allow the attacker to cause the affected device to continuously consume memory, which could cause the device to crash and reload, resulting in a DOS condition. Note: Cisco Discovery Protocol is a Layer 2 protocol. To exploit this vulnerability, an attacker must be in the same broadcast domain as the affected device (Layer 2 adjacent).

A vulnerability in Cisco Aironet Series Access Points Software could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to the improper processing of client packets that are sent to an affected access point (AP). An attacker could exploit this vulnerability by sending a large number of sustained client packets to the affected AP. A successful exploit could allow the attacker to cause the affected AP to crash, resulting in a DoS condition.

A vulnerability in the WLAN Local Profiling feature of Cisco IOS XE Wireless Controller Software for the Cisco Catalyst 9000 Family could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition on an affected device. The vulnerability is due to incorrect parsing of HTTP packets while performing HTTP-based endpoint device classifications. An attacker could exploit this vulnerability by sending a crafted HTTP packet to an affected device. A successful exploit could cause an affected device to reboot, resulting in a DoS condition.