In the Linux kernel, the following vulnerability has been resolved: ext4: regenerate buddy after block freeing failed if under fc replay This mostly reverts commit 6bd97bf273bd ("ext4: remove redundant mb_regenerate_buddy()") and reintroduces mb_regenerate_buddy(). Based on code in mb_free_blocks(), fast commit replay can end up marking as free blocks that are already marked as such. This causes corruption of the buddy bitmap so we need to regenerate it in that case.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: validate the parameters of bo mapping operations more clearly Verify the parameters of amdgpu_vm_bo_(map/replace_map/clearing_mappings) in one common place.

In the Linux kernel, the following vulnerability has been resolved: interconnect: qcom: sc8180x: Mark CO0 BCM keepalive The CO0 BCM needs to be up at all times, otherwise some hardware (like the UFS controller) loses its connection to the rest of the SoC, resulting in a hang of the platform, accompanied by a spectacular logspam. Mark it as keepalive to prevent such cases.

In the Linux kernel, the following vulnerability has been resolved: net: phy: qcom: at803x: fix kernel panic with at8031_probe On reworking and splitting the at803x driver, in splitting function of at803x PHYs it was added a NULL dereference bug where priv is referenced before it's actually allocated and then is tried to write to for the is_1000basex and is_fiber variables in the case of at8031, writing on the wrong address. Fix this by correctly setting priv local variable only after at803x_probe is called and actually allocates priv in the phydev struct.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix use-after-free bug The bug can be triggered by sending a single amdgpu_gem_userptr_ioctl to the AMDGPU DRM driver on any ASICs with an invalid address and size. The bug was reported by Joonkyo Jung <joonkyoj@yonsei.ac.kr>. For example the following code: static void Syzkaller1(int fd) { struct drm_amdgpu_gem_userptr arg; int ret; arg.addr = 0xffffffffffff0000; arg.size = 0x80000000; /*2 Gb*/ arg.flags = 0x7; ret = drmIoctl(fd, 0xc1186451/*amdgpu_gem_userptr_ioctl*/, &arg); } Due to the address and size are not valid there is a failure in amdgpu_hmm_register->mmu_interval_notifier_insert->__mmu_interval_notifier_insert-> check_shl_overflow, but we even the amdgpu_hmm_register failure we still call amdgpu_hmm_unregister into amdgpu_gem_object_free which causes access to a bad address. The following stack is below when the issue is reproduced when Kazan is enabled: [ +0.000014] Hardware name: ASUS System Product Name/ROG STRIX B550-F GAMING (WI-FI), BIOS 1401 12/03/2020 [ +0.000009] RIP: 0010:mmu_interval_notifier_remove+0x327/0x340 [ +0.000017] Code: ff ff 49 89 44 24 08 48 b8 00 01 00 00 00 00 ad de 4c 89 f7 49 89 47 40 48 83 c0 22 49 89 47 48 e8 ce d1 2d 01 e9 32 ff ff ff <0f> 0b e9 16 ff ff ff 4c 89 ef e8 fa 14 b3 ff e9 36 ff ff ff e8 80 [ +0.000014] RSP: 0018:ffffc90002657988 EFLAGS: 00010246 [ +0.000013] RAX: 0000000000000000 RBX: 1ffff920004caf35 RCX: ffffffff8160565b [ +0.000011] RDX: dffffc0000000000 RSI: 0000000000000004 RDI: ffff8881a9f78260 [ +0.000010] RBP: ffffc90002657a70 R08: 0000000000000001 R09: fffff520004caf25 [ +0.000010] R10: 0000000000000003 R11: ffffffff8161d1d6 R12: ffff88810e988c00 [ +0.000010] R13: ffff888126fb5a00 R14: ffff88810e988c0c R15: ffff8881a9f78260 [ +0.000011] FS: 00007ff9ec848540(0000) GS:ffff8883cc880000(0000) knlGS:0000000000000000 [ +0.000012] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ +0.000010] CR2: 000055b3f7e14328 CR3: 00000001b5770000 CR4: 0000000000350ef0 [ +0.000010] Call Trace: [ +0.000006] <TASK> [ +0.000007] ? show_regs+0x6a/0x80 [ +0.000018] ? __warn+0xa5/0x1b0 [ +0.000019] ? mmu_interval_notifier_remove+0x327/0x340 [ +0.000018] ? report_bug+0x24a/0x290 [ +0.000022] ? handle_bug+0x46/0x90 [ +0.000015] ? exc_invalid_op+0x19/0x50 [ +0.000016] ? asm_exc_invalid_op+0x1b/0x20 [ +0.000017] ? kasan_save_stack+0x26/0x50 [ +0.000017] ? mmu_interval_notifier_remove+0x23b/0x340 [ +0.000019] ? mmu_interval_notifier_remove+0x327/0x340 [ +0.000019] ? mmu_interval_notifier_remove+0x23b/0x340 [ +0.000020] ? __pfx_mmu_interval_notifier_remove+0x10/0x10 [ +0.000017] ? kasan_save_alloc_info+0x1e/0x30 [ +0.000018] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? __kasan_kmalloc+0xb1/0xc0 [ +0.000018] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? __kasan_check_read+0x11/0x20 [ +0.000020] amdgpu_hmm_unregister+0x34/0x50 [amdgpu] [ +0.004695] amdgpu_gem_object_free+0x66/0xa0 [amdgpu] [ +0.004534] ? __pfx_amdgpu_gem_object_free+0x10/0x10 [amdgpu] [ +0.004291] ? do_syscall_64+0x5f/0xe0 [ +0.000023] ? srso_return_thunk+0x5/0x5f [ +0.000017] drm_gem_object_free+0x3b/0x50 [drm] [ +0.000489] amdgpu_gem_userptr_ioctl+0x306/0x500 [amdgpu] [ +0.004295] ? __pfx_amdgpu_gem_userptr_ioctl+0x10/0x10 [amdgpu] [ +0.004270] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? __this_cpu_preempt_check+0x13/0x20 [ +0.000015] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ +0.000020] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? asm_sysvec_apic_timer_interrupt+0x1b/0x20 [ +0.000022] ? drm_ioctl_kernel+0x17b/0x1f0 [drm] [ +0.000496] ? __pfx_amdgpu_gem_userptr_ioctl+0x10/0x10 [amdgpu] [ +0.004272] ? drm_ioctl_kernel+0x190/0x1f0 [drm] [ +0.000492] drm_ioctl_kernel+0x140/0x1f0 [drm] [ +0.000497] ? __pfx_amdgpu_gem_userptr_ioctl+0x10/0x10 [amdgpu] [ +0.004297] ? __pfx_drm_ioctl_kernel+0x10/0x10 [d ---truncated---

In the Linux kernel, the following vulnerability has been resolved: f2fs: compress: fix to cover normal cluster write with cp_rwsem When we overwrite compressed cluster w/ normal cluster, we should not unlock cp_rwsem during f2fs_write_raw_pages(), otherwise data will be corrupted if partial blocks were persisted before CP & SPOR, due to cluster metadata wasn't updated atomically.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix potential null pointer dereference in dc_dmub_srv Fixes potential null pointer dereference warnings in the dc_dmub_srv_cmd_list_queue_execute() and dc_dmub_srv_is_hw_pwr_up() functions. In both functions, the 'dc_dmub_srv' variable was being dereferenced before it was checked for null. This could lead to a null pointer dereference if 'dc_dmub_srv' is null. The fix is to check if 'dc_dmub_srv' is null before dereferencing it. Thus moving the null checks for 'dc_dmub_srv' to the beginning of the functions to ensure that 'dc_dmub_srv' is not null when it is dereferenced. Found by smatch & thus fixing the below: drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:133 dc_dmub_srv_cmd_list_queue_execute() warn: variable dereferenced before check 'dc_dmub_srv' (see line 128) drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dmub_srv.c:1167 dc_dmub_srv_is_hw_pwr_up() warn: variable dereferenced before check 'dc_dmub_srv' (see line 1164)

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix racing between bpf_timer_cancel_and_free and bpf_timer_cancel The following race is possible between bpf_timer_cancel_and_free and bpf_timer_cancel. It will lead a UAF on the timer->timer. bpf_timer_cancel(); spin_lock(); t = timer->time; spin_unlock(); bpf_timer_cancel_and_free(); spin_lock(); t = timer->timer; timer->timer = NULL; spin_unlock(); hrtimer_cancel(&t->timer); kfree(t); /* UAF on t */ hrtimer_cancel(&t->timer); In bpf_timer_cancel_and_free, this patch frees the timer->timer after a rcu grace period. This requires a rcu_head addition to the "struct bpf_hrtimer". Another kfree(t) happens in bpf_timer_init, this does not need a kfree_rcu because it is still under the spin_lock and timer->timer has not been visible by others yet. In bpf_timer_cancel, rcu_read_lock() is added because this helper can be used in a non rcu critical section context (e.g. from a sleepable bpf prog). Other timer->timer usages in helpers.c have been audited, bpf_timer_cancel() is the only place where timer->timer is used outside of the spin_lock. Another solution considered is to mark a t->flag in bpf_timer_cancel and clear it after hrtimer_cancel() is done. In bpf_timer_cancel_and_free, it busy waits for the flag to be cleared before kfree(t). This patch goes with a straight forward solution and frees timer->timer after a rcu grace period.

In the Linux kernel, the following vulnerability has been resolved: spi: lpspi: Avoid potential use-after-free in probe() fsl_lpspi_probe() is allocating/disposing memory manually with spi_alloc_host()/spi_alloc_target(), but uses devm_spi_register_controller(). In case of error after the latter call the memory will be explicitly freed in the probe function by spi_controller_put() call, but used afterwards by "devm" management outside probe() (spi_unregister_controller() <- devm_spi_unregister() below). Unable to handle kernel NULL pointer dereference at virtual address 0000000000000070 ... Call trace: kernfs_find_ns kernfs_find_and_get_ns sysfs_remove_group sysfs_remove_groups device_remove_attrs device_del spi_unregister_controller devm_spi_unregister release_nodes devres_release_all really_probe driver_probe_device __device_attach_driver bus_for_each_drv __device_attach device_initial_probe bus_probe_device deferred_probe_work_func process_one_work worker_thread kthread ret_from_fork

In the Linux kernel, the following vulnerability has been resolved: xdp: use flags field to disambiguate broadcast redirect When redirecting a packet using XDP, the bpf_redirect_map() helper will set up the redirect destination information in struct bpf_redirect_info (using the __bpf_xdp_redirect_map() helper function), and the xdp_do_redirect() function will read this information after the XDP program returns and pass the frame on to the right redirect destination. When using the BPF_F_BROADCAST flag to do multicast redirect to a whole map, __bpf_xdp_redirect_map() sets the 'map' pointer in struct bpf_redirect_info to point to the destination map to be broadcast. And xdp_do_redirect() reacts to the value of this map pointer to decide whether it's dealing with a broadcast or a single-value redirect. However, if the destination map is being destroyed before xdp_do_redirect() is called, the map pointer will be cleared out (by bpf_clear_redirect_map()) without waiting for any XDP programs to stop running. This causes xdp_do_redirect() to think that the redirect was to a single target, but the target pointer is also NULL (since broadcast redirects don't have a single target), so this causes a crash when a NULL pointer is passed to dev_map_enqueue(). To fix this, change xdp_do_redirect() to react directly to the presence of the BPF_F_BROADCAST flag in the 'flags' value in struct bpf_redirect_info to disambiguate between a single-target and a broadcast redirect. And only read the 'map' pointer if the broadcast flag is set, aborting if that has been cleared out in the meantime. This prevents the crash, while keeping the atomic (cmpxchg-based) clearing of the map pointer itself, and without adding any more checks in the non-broadcast fast path.

In the Linux kernel, the following vulnerability has been resolved: hsr: Fix uninit-value access in hsr_get_node() KMSAN reported the following uninit-value access issue [1]: ===================================================== BUG: KMSAN: uninit-value in hsr_get_node+0xa2e/0xa40 net/hsr/hsr_framereg.c:246 hsr_get_node+0xa2e/0xa40 net/hsr/hsr_framereg.c:246 fill_frame_info net/hsr/hsr_forward.c:577 [inline] hsr_forward_skb+0xe12/0x30e0 net/hsr/hsr_forward.c:615 hsr_dev_xmit+0x1a1/0x270 net/hsr/hsr_device.c:223 __netdev_start_xmit include/linux/netdevice.h:4940 [inline] netdev_start_xmit include/linux/netdevice.h:4954 [inline] xmit_one net/core/dev.c:3548 [inline] dev_hard_start_xmit+0x247/0xa10 net/core/dev.c:3564 __dev_queue_xmit+0x33b8/0x5130 net/core/dev.c:4349 dev_queue_xmit include/linux/netdevice.h:3134 [inline] packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3087 [inline] packet_sendmsg+0x8b1d/0x9f30 net/packet/af_packet.c:3119 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] __sys_sendto+0x735/0xa10 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1c0 net/socket.c:2199 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x6d/0x140 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Uninit was created at: slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768 slab_alloc_node mm/slub.c:3478 [inline] kmem_cache_alloc_node+0x5e9/0xb10 mm/slub.c:3523 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:560 __alloc_skb+0x318/0x740 net/core/skbuff.c:651 alloc_skb include/linux/skbuff.h:1286 [inline] alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6334 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2787 packet_alloc_skb net/packet/af_packet.c:2936 [inline] packet_snd net/packet/af_packet.c:3030 [inline] packet_sendmsg+0x70e8/0x9f30 net/packet/af_packet.c:3119 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] __sys_sendto+0x735/0xa10 net/socket.c:2191 __do_sys_sendto net/socket.c:2203 [inline] __se_sys_sendto net/socket.c:2199 [inline] __x64_sys_sendto+0x125/0x1c0 net/socket.c:2199 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x6d/0x140 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b CPU: 1 PID: 5033 Comm: syz-executor334 Not tainted 6.7.0-syzkaller-00562-g9f8413c4a66f #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023 ===================================================== If the packet type ID field in the Ethernet header is either ETH_P_PRP or ETH_P_HSR, but it is not followed by an HSR tag, hsr_get_skb_sequence_nr() reads an invalid value as a sequence number. This causes the above issue. This patch fixes the issue by returning NULL if the Ethernet header is not followed by an HSR tag.

In the Linux kernel, the following vulnerability has been resolved: NFSv4.2: fix nfs4_listxattr kernel BUG at mm/usercopy.c:102 A call to listxattr() with a buffer size = 0 returns the actual size of the buffer needed for a subsequent call. When size > 0, nfs4_listxattr() does not return an error because either generic_listxattr() or nfs4_listxattr_nfs4_label() consumes exactly all the bytes then size is 0 when calling nfs4_listxattr_nfs4_user() which then triggers the following kernel BUG: [ 99.403778] kernel BUG at mm/usercopy.c:102! [ 99.404063] Internal error: Oops - BUG: 00000000f2000800 [#1] SMP [ 99.408463] CPU: 0 PID: 3310 Comm: python3 Not tainted 6.6.0-61.fc40.aarch64 #1 [ 99.415827] Call trace: [ 99.415985] usercopy_abort+0x70/0xa0 [ 99.416227] __check_heap_object+0x134/0x158 [ 99.416505] check_heap_object+0x150/0x188 [ 99.416696] __check_object_size.part.0+0x78/0x168 [ 99.416886] __check_object_size+0x28/0x40 [ 99.417078] listxattr+0x8c/0x120 [ 99.417252] path_listxattr+0x78/0xe0 [ 99.417476] __arm64_sys_listxattr+0x28/0x40 [ 99.417723] invoke_syscall+0x78/0x100 [ 99.417929] el0_svc_common.constprop.0+0x48/0xf0 [ 99.418186] do_el0_svc+0x24/0x38 [ 99.418376] el0_svc+0x3c/0x110 [ 99.418554] el0t_64_sync_handler+0x120/0x130 [ 99.418788] el0t_64_sync+0x194/0x198 [ 99.418994] Code: aa0003e3 d000a3e0 91310000 97f49bdb (d4210000) Issue is reproduced when generic_listxattr() returns 'system.nfs4_acl', thus calling lisxattr() with size = 16 will trigger the bug. Add check on nfs4_listxattr() to return ERANGE error when it is called with size > 0 and the return value is greater than size.

In the Linux kernel, the following vulnerability has been resolved: md: Fix missing release of 'active_io' for flush submit_flushes atomic_set(&mddev->flush_pending, 1); rdev_for_each_rcu(rdev, mddev) atomic_inc(&mddev->flush_pending); bi->bi_end_io = md_end_flush submit_bio(bi); /* flush io is done first */ md_end_flush if (atomic_dec_and_test(&mddev->flush_pending)) percpu_ref_put(&mddev->active_io) -> active_io is not released if (atomic_dec_and_test(&mddev->flush_pending)) -> missing release of active_io For consequence, mddev_suspend() will wait for 'active_io' to be zero forever. Fix this problem by releasing 'active_io' in submit_flushes() if 'flush_pending' is decreased to zero.

In the Linux kernel, the following vulnerability has been resolved: fs,hugetlb: fix NULL pointer dereference in hugetlbs_fill_super When configuring a hugetlb filesystem via the fsconfig() syscall, there is a possible NULL dereference in hugetlbfs_fill_super() caused by assigning NULL to ctx->hstate in hugetlbfs_parse_param() when the requested pagesize is non valid. E.g: Taking the following steps: fd = fsopen("hugetlbfs", FSOPEN_CLOEXEC); fsconfig(fd, FSCONFIG_SET_STRING, "pagesize", "1024", 0); fsconfig(fd, FSCONFIG_CMD_CREATE, NULL, NULL, 0); Given that the requested "pagesize" is invalid, ctxt->hstate will be replaced with NULL, losing its previous value, and we will print an error: ... ... case Opt_pagesize: ps = memparse(param->string, &rest); ctx->hstate = h; if (!ctx->hstate) { pr_err("Unsupported page size %lu MB\n", ps / SZ_1M); return -EINVAL; } return 0; ... ... This is a problem because later on, we will dereference ctxt->hstate in hugetlbfs_fill_super() ... ... sb->s_blocksize = huge_page_size(ctx->hstate); ... ... Causing below Oops. Fix this by replacing cxt->hstate value only when then pagesize is known to be valid. kernel: hugetlbfs: Unsupported page size 0 MB kernel: BUG: kernel NULL pointer dereference, address: 0000000000000028 kernel: #PF: supervisor read access in kernel mode kernel: #PF: error_code(0x0000) - not-present page kernel: PGD 800000010f66c067 P4D 800000010f66c067 PUD 1b22f8067 PMD 0 kernel: Oops: 0000 [#1] PREEMPT SMP PTI kernel: CPU: 4 PID: 5659 Comm: syscall Tainted: G E 6.8.0-rc2-default+ #22 5a47c3fef76212addcc6eb71344aabc35190ae8f kernel: Hardware name: Intel Corp. GROVEPORT/GROVEPORT, BIOS GVPRCRB1.86B.0016.D04.1705030402 05/03/2017 kernel: RIP: 0010:hugetlbfs_fill_super+0xb4/0x1a0 kernel: Code: 48 8b 3b e8 3e c6 ed ff 48 85 c0 48 89 45 20 0f 84 d6 00 00 00 48 b8 ff ff ff ff ff ff ff 7f 4c 89 e7 49 89 44 24 20 48 8b 03 <8b> 48 28 b8 00 10 00 00 48 d3 e0 49 89 44 24 18 48 8b 03 8b 40 28 kernel: RSP: 0018:ffffbe9960fcbd48 EFLAGS: 00010246 kernel: RAX: 0000000000000000 RBX: ffff9af5272ae780 RCX: 0000000000372004 kernel: RDX: ffffffffffffffff RSI: ffffffffffffffff RDI: ffff9af555e9b000 kernel: RBP: ffff9af52ee66b00 R08: 0000000000000040 R09: 0000000000370004 kernel: R10: ffffbe9960fcbd48 R11: 0000000000000040 R12: ffff9af555e9b000 kernel: R13: ffffffffa66b86c0 R14: ffff9af507d2f400 R15: ffff9af507d2f400 kernel: FS: 00007ffbc0ba4740(0000) GS:ffff9b0bd7000000(0000) knlGS:0000000000000000 kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 kernel: CR2: 0000000000000028 CR3: 00000001b1ee0000 CR4: 00000000001506f0 kernel: Call Trace: kernel: <TASK> kernel: ? __die_body+0x1a/0x60 kernel: ? page_fault_oops+0x16f/0x4a0 kernel: ? search_bpf_extables+0x65/0x70 kernel: ? fixup_exception+0x22/0x310 kernel: ? exc_page_fault+0x69/0x150 kernel: ? asm_exc_page_fault+0x22/0x30 kernel: ? __pfx_hugetlbfs_fill_super+0x10/0x10 kernel: ? hugetlbfs_fill_super+0xb4/0x1a0 kernel: ? hugetlbfs_fill_super+0x28/0x1a0 kernel: ? __pfx_hugetlbfs_fill_super+0x10/0x10 kernel: vfs_get_super+0x40/0xa0 kernel: ? __pfx_bpf_lsm_capable+0x10/0x10 kernel: vfs_get_tree+0x25/0xd0 kernel: vfs_cmd_create+0x64/0xe0 kernel: __x64_sys_fsconfig+0x395/0x410 kernel: do_syscall_64+0x80/0x160 kernel: ? syscall_exit_to_user_mode+0x82/0x240 kernel: ? do_syscall_64+0x8d/0x160 kernel: ? syscall_exit_to_user_mode+0x82/0x240 kernel: ? do_syscall_64+0x8d/0x160 kernel: ? exc_page_fault+0x69/0x150 kernel: entry_SYSCALL_64_after_hwframe+0x6e/0x76 kernel: RIP: 0033:0x7ffbc0cb87c9 kernel: Code: 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 97 96 0d 00 f7 d8 64 89 01 48 kernel: RSP: 002b:00007ffc29d2f388 EFLAGS: 00000206 ORIG_RAX: 00000000000001af kernel: RAX: fffffffffff ---truncated---

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Update cpu_sibling_map when disabling nonboot CPUs Update cpu_sibling_map when disabling nonboot CPUs by defining & calling clear_cpu_sibling_map(), otherwise we get such errors on SMT systems: jump label: negative count! WARNING: CPU: 6 PID: 45 at kernel/jump_label.c:263 __static_key_slow_dec_cpuslocked+0xec/0x100 CPU: 6 PID: 45 Comm: cpuhp/6 Not tainted 6.8.0-rc5+ #1340 pc 90000000004c302c ra 90000000004c302c tp 90000001005bc000 sp 90000001005bfd20 a0 000000000000001b a1 900000000224c278 a2 90000001005bfb58 a3 900000000224c280 a4 900000000224c278 a5 90000001005bfb50 a6 0000000000000001 a7 0000000000000001 t0 ce87a4763eb5234a t1 ce87a4763eb5234a t2 0000000000000000 t3 0000000000000000 t4 0000000000000006 t5 0000000000000000 t6 0000000000000064 t7 0000000000001964 t8 000000000009ebf6 u0 9000000001f2a068 s9 0000000000000000 s0 900000000246a2d8 s1 ffffffffffffffff s2 ffffffffffffffff s3 90000000021518c0 s4 0000000000000040 s5 9000000002151058 s6 9000000009828e40 s7 00000000000000b4 s8 0000000000000006 ra: 90000000004c302c __static_key_slow_dec_cpuslocked+0xec/0x100 ERA: 90000000004c302c __static_key_slow_dec_cpuslocked+0xec/0x100 CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE) PRMD: 00000004 (PPLV0 +PIE -PWE) EUEN: 00000000 (-FPE -SXE -ASXE -BTE) ECFG: 00071c1c (LIE=2-4,10-12 VS=7) ESTAT: 000c0000 [BRK] (IS= ECode=12 EsubCode=0) PRID: 0014d000 (Loongson-64bit, Loongson-3A6000-HV) CPU: 6 PID: 45 Comm: cpuhp/6 Not tainted 6.8.0-rc5+ #1340 Stack : 0000000000000000 900000000203f258 900000000179afc8 90000001005bc000 90000001005bf980 0000000000000000 90000001005bf988 9000000001fe0be0 900000000224c280 900000000224c278 90000001005bf8c0 0000000000000001 0000000000000001 ce87a4763eb5234a 0000000007f38000 90000001003f8cc0 0000000000000000 0000000000000006 0000000000000000 4c206e6f73676e6f 6f4c203a656d616e 000000000009ec99 0000000007f38000 0000000000000000 900000000214b000 9000000001fe0be0 0000000000000004 0000000000000000 0000000000000107 0000000000000009 ffffffffffafdabe 00000000000000b4 0000000000000006 90000000004c302c 9000000000224528 00005555939a0c7c 00000000000000b0 0000000000000004 0000000000000000 0000000000071c1c ... Call Trace: [<9000000000224528>] show_stack+0x48/0x1a0 [<900000000179afc8>] dump_stack_lvl+0x78/0xa0 [<9000000000263ed0>] __warn+0x90/0x1a0 [<90000000017419b8>] report_bug+0x1b8/0x280 [<900000000179c564>] do_bp+0x264/0x420 [<90000000004c302c>] __static_key_slow_dec_cpuslocked+0xec/0x100 [<90000000002b4d7c>] sched_cpu_deactivate+0x2fc/0x300 [<9000000000266498>] cpuhp_invoke_callback+0x178/0x8a0 [<9000000000267f70>] cpuhp_thread_fun+0xf0/0x240 [<90000000002a117c>] smpboot_thread_fn+0x1dc/0x2e0 [<900000000029a720>] kthread+0x140/0x160 [<9000000000222288>] ret_from_kernel_thread+0xc/0xa4

In the Linux kernel, the following vulnerability has been resolved: net: mctp: take ownership of skb in mctp_local_output Currently, mctp_local_output only takes ownership of skb on success, and we may leak an skb if mctp_local_output fails in specific states; the skb ownership isn't transferred until the actual output routing occurs. Instead, make mctp_local_output free the skb on all error paths up to the route action, so it always consumes the passed skb.

In the Linux kernel, the following vulnerability has been resolved: fbcon: always restore the old font data in fbcon_do_set_font() Commit a5a923038d70 (fbdev: fbcon: Properly revert changes when vc_resize() failed) started restoring old font data upon failure (of vc_resize()). But it performs so only for user fonts. It means that the "system"/internal fonts are not restored at all. So in result, the very first call to fbcon_do_set_font() performs no restore at all upon failing vc_resize(). This can be reproduced by Syzkaller to crash the system on the next invocation of font_get(). It's rather hard to hit the allocation failure in vc_resize() on the first font_set(), but not impossible. Esp. if fault injection is used to aid the execution/failure. It was demonstrated by Sirius: BUG: unable to handle page fault for address: fffffffffffffff8 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD cb7b067 P4D cb7b067 PUD cb7d067 PMD 0 Oops: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 8007 Comm: poc Not tainted 6.7.0-g9d1694dc91ce #20 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 RIP: 0010:fbcon_get_font+0x229/0x800 drivers/video/fbdev/core/fbcon.c:2286 Call Trace: <TASK> con_font_get drivers/tty/vt/vt.c:4558 [inline] con_font_op+0x1fc/0xf20 drivers/tty/vt/vt.c:4673 vt_k_ioctl drivers/tty/vt/vt_ioctl.c:474 [inline] vt_ioctl+0x632/0x2ec0 drivers/tty/vt/vt_ioctl.c:752 tty_ioctl+0x6f8/0x1570 drivers/tty/tty_io.c:2803 vfs_ioctl fs/ioctl.c:51 [inline] ... So restore the font data in any case, not only for user fonts. Note the later 'if' is now protected by 'old_userfont' and not 'old_data' as the latter is always set now. (And it is supposed to be non-NULL. Otherwise we would see the bug above again.)

In the Linux kernel, the following vulnerability has been resolved: do_sys_name_to_handle(): use kzalloc() to fix kernel-infoleak syzbot identified a kernel information leak vulnerability in do_sys_name_to_handle() and issued the following report [1]. [1] "BUG: KMSAN: kernel-infoleak in instrument_copy_to_user include/linux/instrumented.h:114 [inline] BUG: KMSAN: kernel-infoleak in _copy_to_user+0xbc/0x100 lib/usercopy.c:40 instrument_copy_to_user include/linux/instrumented.h:114 [inline] _copy_to_user+0xbc/0x100 lib/usercopy.c:40 copy_to_user include/linux/uaccess.h:191 [inline] do_sys_name_to_handle fs/fhandle.c:73 [inline] __do_sys_name_to_handle_at fs/fhandle.c:112 [inline] __se_sys_name_to_handle_at+0x949/0xb10 fs/fhandle.c:94 __x64_sys_name_to_handle_at+0xe4/0x140 fs/fhandle.c:94 ... Uninit was created at: slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768 slab_alloc_node mm/slub.c:3478 [inline] __kmem_cache_alloc_node+0x5c9/0x970 mm/slub.c:3517 __do_kmalloc_node mm/slab_common.c:1006 [inline] __kmalloc+0x121/0x3c0 mm/slab_common.c:1020 kmalloc include/linux/slab.h:604 [inline] do_sys_name_to_handle fs/fhandle.c:39 [inline] __do_sys_name_to_handle_at fs/fhandle.c:112 [inline] __se_sys_name_to_handle_at+0x441/0xb10 fs/fhandle.c:94 __x64_sys_name_to_handle_at+0xe4/0x140 fs/fhandle.c:94 ... Bytes 18-19 of 20 are uninitialized Memory access of size 20 starts at ffff888128a46380 Data copied to user address 0000000020000240" Per Chuck Lever's suggestion, use kzalloc() instead of kmalloc() to solve the problem.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: Avoid potential use-after-free in hci_error_reset While handling the HCI_EV_HARDWARE_ERROR event, if the underlying BT controller is not responding, the GPIO reset mechanism would free the hci_dev and lead to a use-after-free in hci_error_reset. Here's the call trace observed on a ChromeOS device with Intel AX201: queue_work_on+0x3e/0x6c __hci_cmd_sync_sk+0x2ee/0x4c0 [bluetooth <HASH:3b4a6>] ? init_wait_entry+0x31/0x31 __hci_cmd_sync+0x16/0x20 [bluetooth <HASH:3b4a 6>] hci_error_reset+0x4f/0xa4 [bluetooth <HASH:3b4a 6>] process_one_work+0x1d8/0x33f worker_thread+0x21b/0x373 kthread+0x13a/0x152 ? pr_cont_work+0x54/0x54 ? kthread_blkcg+0x31/0x31 ret_from_fork+0x1f/0x30 This patch holds the reference count on the hci_dev while processing a HCI_EV_HARDWARE_ERROR event to avoid potential crash.

In the Linux kernel, the following vulnerability has been resolved: media: usbtv: Remove useless locks in usbtv_video_free() Remove locks calls in usbtv_video_free() because are useless and may led to a deadlock as reported here: https://syzkaller.appspot.com/x/bisect.txt?x=166dc872180000 Also remove usbtv_stop() call since it will be called when unregistering the device. Before 'c838530d230b' this issue would only be noticed if you disconnect while streaming and now it is noticeable even when disconnecting while not streaming. [hverkuil: fix minor spelling mistake in log message]

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix 'panel_cntl' could be null in 'dcn21_set_backlight_level()' 'panel_cntl' structure used to control the display panel could be null, dereferencing it could lead to a null pointer access. Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn21/dcn21_hwseq.c:269 dcn21_set_backlight_level() error: we previously assumed 'panel_cntl' could be null (see line 250)

In the Linux kernel, the following vulnerability has been resolved: scsi: core: Fix unremoved procfs host directory regression Commit fc663711b944 ("scsi: core: Remove the /proc/scsi/${proc_name} directory earlier") fixed a bug related to modules loading/unloading, by adding a call to scsi_proc_hostdir_rm() on scsi_remove_host(). But that led to a potential duplicate call to the hostdir_rm() routine, since it's also called from scsi_host_dev_release(). That triggered a regression report, which was then fixed by commit be03df3d4bfe ("scsi: core: Fix a procfs host directory removal regression"). The fix just dropped the hostdir_rm() call from dev_release(). But it happens that this proc directory is created on scsi_host_alloc(), and that function "pairs" with scsi_host_dev_release(), while scsi_remove_host() pairs with scsi_add_host(). In other words, it seems the reason for removing the proc directory on dev_release() was meant to cover cases in which a SCSI host structure was allocated, but the call to scsi_add_host() didn't happen. And that pattern happens to exist in some error paths, for example. Syzkaller causes that by using USB raw gadget device, error'ing on usb-storage driver, at usb_stor_probe2(). By checking that path, we can see that the BadDevice label leads to a scsi_host_put() after a SCSI host allocation, but there's no call to scsi_add_host() in such path. That leads to messages like this in dmesg (and a leak of the SCSI host proc structure): usb-storage 4-1:87.51: USB Mass Storage device detected proc_dir_entry 'scsi/usb-storage' already registered WARNING: CPU: 1 PID: 3519 at fs/proc/generic.c:377 proc_register+0x347/0x4e0 fs/proc/generic.c:376 The proper fix seems to still call scsi_proc_hostdir_rm() on dev_release(), but guard that with the state check for SHOST_CREATED; there is even a comment in scsi_host_dev_release() detailing that: such conditional is meant for cases where the SCSI host was allocated but there was no calls to {add,remove}_host(), like the usb-storage case. This is what we propose here and with that, the error path of usb-storage does not trigger the warning anymore.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btnxpuart: Fix btnxpuart_close Fix scheduling while atomic BUG in btnxpuart_close(), properly purge the transmit queue and free the receive skb. [ 10.973809] BUG: scheduling while atomic: kworker/u9:0/80/0x00000002 ... [ 10.980740] CPU: 3 PID: 80 Comm: kworker/u9:0 Not tainted 6.8.0-rc7-0.0.0-devel-00005-g61fdfceacf09 #1 [ 10.980751] Hardware name: Toradex Verdin AM62 WB on Dahlia Board (DT) [ 10.980760] Workqueue: hci0 hci_power_off [bluetooth] [ 10.981169] Call trace: ... [ 10.981363] uart_update_mctrl+0x58/0x78 [ 10.981373] uart_dtr_rts+0x104/0x114 [ 10.981381] tty_port_shutdown+0xd4/0xdc [ 10.981396] tty_port_close+0x40/0xbc [ 10.981407] uart_close+0x34/0x9c [ 10.981414] ttyport_close+0x50/0x94 [ 10.981430] serdev_device_close+0x40/0x50 [ 10.981442] btnxpuart_close+0x24/0x98 [btnxpuart] [ 10.981469] hci_dev_close_sync+0x2d8/0x718 [bluetooth] [ 10.981728] hci_dev_do_close+0x2c/0x70 [bluetooth] [ 10.981862] hci_power_off+0x20/0x64 [bluetooth]

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: gadget: Fix NULL pointer dereference in dwc3_gadget_suspend In current scenario if Plug-out and Plug-In performed continuously there could be a chance while checking for dwc->gadget_driver in dwc3_gadget_suspend, a NULL pointer dereference may occur. Call Stack: CPU1: CPU2: gadget_unbind_driver dwc3_suspend_common dwc3_gadget_stop dwc3_gadget_suspend dwc3_disconnect_gadget CPU1 basically clears the variable and CPU2 checks the variable. Consider CPU1 is running and right before gadget_driver is cleared and in parallel CPU2 executes dwc3_gadget_suspend where it finds dwc->gadget_driver which is not NULL and resumes execution and then CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where it checks dwc->gadget_driver is already NULL because of which the NULL pointer deference occur.

In the Linux kernel, the following vulnerability has been resolved: thermal/drivers/mediatek/lvts_thermal: Fix a memory leak in an error handling path If devm_krealloc() fails, then 'efuse' is leaking. So free it to avoid a leak.

In the Linux kernel, the following vulnerability has been resolved: backlight: hx8357: Fix potential NULL pointer dereference The "im" pins are optional. Add missing check in the hx8357_probe().

In the Linux kernel, the following vulnerability has been resolved: dm-crypt, dm-verity: disable tasklets Tasklets have an inherent problem with memory corruption. The function tasklet_action_common calls tasklet_trylock, then it calls the tasklet callback and then it calls tasklet_unlock. If the tasklet callback frees the structure that contains the tasklet or if it calls some code that may free it, tasklet_unlock will write into free memory. The commits 8e14f610159d and d9a02e016aaf try to fix it for dm-crypt, but it is not a sufficient fix and the data corruption can still happen [1]. There is no fix for dm-verity and dm-verity will write into free memory with every tasklet-processed bio. There will be atomic workqueues implemented in the kernel 6.9 [2]. They will have better interface and they will not suffer from the memory corruption problem. But we need something that stops the memory corruption now and that can be backported to the stable kernels. So, I'm proposing this commit that disables tasklets in both dm-crypt and dm-verity. This commit doesn't remove the tasklet support, because the tasklet code will be reused when atomic workqueues will be implemented. [1] https://lore.kernel.org/all/d390d7ee-f142-44d3-822a-87949e14608b@suse.de/T/ [2] https://lore.kernel.org/lkml/20240130091300.2968534-1-tj@kernel.org/

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix variable deferencing before NULL check in edp_setup_replay() In edp_setup_replay(), 'struct dc *dc' & 'struct dmub_replay *replay' was dereferenced before the pointer 'link' & 'replay' NULL check. Fixes the below: drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_edp_panel_control.c:947 edp_setup_replay() warn: variable dereferenced before check 'link' (see line 933)

In the Linux kernel, the following vulnerability has been resolved: clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays The frequency table arrays are supposed to be terminated with an empty element. Add such entry to the end of the arrays where it is missing in order to avoid possible out-of-bound access when the table is traversed by functions like qcom_find_freq() or qcom_find_freq_floor(). Only compile tested.

In the Linux kernel, the following vulnerability has been resolved: tcp: make sure init the accept_queue's spinlocks once When I run syz's reproduction C program locally, it causes the following issue: pvqspinlock: lock 0xffff9d181cd5c660 has corrupted value 0x0! WARNING: CPU: 19 PID: 21160 at __pv_queued_spin_unlock_slowpath (kernel/locking/qspinlock_paravirt.h:508) Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011 RIP: 0010:__pv_queued_spin_unlock_slowpath (kernel/locking/qspinlock_paravirt.h:508) Code: 73 56 3a ff 90 c3 cc cc cc cc 8b 05 bb 1f 48 01 85 c0 74 05 c3 cc cc cc cc 8b 17 48 89 fe 48 c7 c7 30 20 ce 8f e8 ad 56 42 ff <0f> 0b c3 cc cc cc cc 0f 0b 0f 1f 40 00 90 90 90 90 90 90 90 90 90 RSP: 0018:ffffa8d200604cb8 EFLAGS: 00010282 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff9d1ef60e0908 RDX: 00000000ffffffd8 RSI: 0000000000000027 RDI: ffff9d1ef60e0900 RBP: ffff9d181cd5c280 R08: 0000000000000000 R09: 00000000ffff7fff R10: ffffa8d200604b68 R11: ffffffff907dcdc8 R12: 0000000000000000 R13: ffff9d181cd5c660 R14: ffff9d1813a3f330 R15: 0000000000001000 FS: 00007fa110184640(0000) GS:ffff9d1ef60c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000000 CR3: 000000011f65e000 CR4: 00000000000006f0 Call Trace: <IRQ> _raw_spin_unlock (kernel/locking/spinlock.c:186) inet_csk_reqsk_queue_add (net/ipv4/inet_connection_sock.c:1321) inet_csk_complete_hashdance (net/ipv4/inet_connection_sock.c:1358) tcp_check_req (net/ipv4/tcp_minisocks.c:868) tcp_v4_rcv (net/ipv4/tcp_ipv4.c:2260) ip_protocol_deliver_rcu (net/ipv4/ip_input.c:205) ip_local_deliver_finish (net/ipv4/ip_input.c:234) __netif_receive_skb_one_core (net/core/dev.c:5529) process_backlog (./include/linux/rcupdate.h:779) __napi_poll (net/core/dev.c:6533) net_rx_action (net/core/dev.c:6604) __do_softirq (./arch/x86/include/asm/jump_label.h:27) do_softirq (kernel/softirq.c:454 kernel/softirq.c:441) </IRQ> <TASK> __local_bh_enable_ip (kernel/softirq.c:381) __dev_queue_xmit (net/core/dev.c:4374) ip_finish_output2 (./include/net/neighbour.h:540 net/ipv4/ip_output.c:235) __ip_queue_xmit (net/ipv4/ip_output.c:535) __tcp_transmit_skb (net/ipv4/tcp_output.c:1462) tcp_rcv_synsent_state_process (net/ipv4/tcp_input.c:6469) tcp_rcv_state_process (net/ipv4/tcp_input.c:6657) tcp_v4_do_rcv (net/ipv4/tcp_ipv4.c:1929) __release_sock (./include/net/sock.h:1121 net/core/sock.c:2968) release_sock (net/core/sock.c:3536) inet_wait_for_connect (net/ipv4/af_inet.c:609) __inet_stream_connect (net/ipv4/af_inet.c:702) inet_stream_connect (net/ipv4/af_inet.c:748) __sys_connect (./include/linux/file.h:45 net/socket.c:2064) __x64_sys_connect (net/socket.c:2073 net/socket.c:2070 net/socket.c:2070) do_syscall_64 (arch/x86/entry/common.c:51 arch/x86/entry/common.c:82) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:129) RIP: 0033:0x7fa10ff05a3d Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d ab a3 0e 00 f7 d8 64 89 01 48 RSP: 002b:00007fa110183de8 EFLAGS: 00000202 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 0000000020000054 RCX: 00007fa10ff05a3d RDX: 000000000000001c RSI: 0000000020000040 RDI: 0000000000000003 RBP: 00007fa110183e20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000202 R12: 00007fa110184640 R13: 0000000000000000 R14: 00007fa10fe8b060 R15: 00007fff73e23b20 </TASK> The issue triggering process is analyzed as follows: Thread A Thread B tcp_v4_rcv //receive ack TCP packet inet_shutdown tcp_check_req tcp_disconnect //disconnect sock ... tcp_set_state(sk, TCP_CLOSE) inet_csk_complete_hashdance ... inet_csk_reqsk_queue_add ---truncated---

In the Linux kernel, the following vulnerability has been resolved: crypto: xilinx - call finalize with bh disabled When calling crypto_finalize_request, BH should be disabled to avoid triggering the following calltrace: ------------[ cut here ]------------ WARNING: CPU: 2 PID: 74 at crypto/crypto_engine.c:58 crypto_finalize_request+0xa0/0x118 Modules linked in: cryptodev(O) CPU: 2 PID: 74 Comm: firmware:zynqmp Tainted: G O 6.8.0-rc1-yocto-standard #323 Hardware name: ZynqMP ZCU102 Rev1.0 (DT) pstate: 40000005 (nZcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : crypto_finalize_request+0xa0/0x118 lr : crypto_finalize_request+0x104/0x118 sp : ffffffc085353ce0 x29: ffffffc085353ce0 x28: 0000000000000000 x27: ffffff8808ea8688 x26: ffffffc081715038 x25: 0000000000000000 x24: ffffff880100db00 x23: ffffff880100da80 x22: 0000000000000000 x21: 0000000000000000 x20: ffffff8805b14000 x19: ffffff880100da80 x18: 0000000000010450 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000003 x13: 0000000000000000 x12: ffffff880100dad0 x11: 0000000000000000 x10: ffffffc0832dcd08 x9 : ffffffc0812416d8 x8 : 00000000000001f4 x7 : ffffffc0830d2830 x6 : 0000000000000001 x5 : ffffffc082091000 x4 : ffffffc082091658 x3 : 0000000000000000 x2 : ffffffc7f9653000 x1 : 0000000000000000 x0 : ffffff8802d20000 Call trace: crypto_finalize_request+0xa0/0x118 crypto_finalize_aead_request+0x18/0x30 zynqmp_handle_aes_req+0xcc/0x388 crypto_pump_work+0x168/0x2d8 kthread_worker_fn+0xfc/0x3a0 kthread+0x118/0x138 ret_from_fork+0x10/0x20 irq event stamp: 40 hardirqs last enabled at (39): [<ffffffc0812416f8>] _raw_spin_unlock_irqrestore+0x70/0xb0 hardirqs last disabled at (40): [<ffffffc08122d208>] el1_dbg+0x28/0x90 softirqs last enabled at (36): [<ffffffc080017dec>] kernel_neon_begin+0x8c/0xf0 softirqs last disabled at (34): [<ffffffc080017dc0>] kernel_neon_begin+0x60/0xf0 ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: nilfs2: fix failure to detect DAT corruption in btree and direct mappings Patch series "nilfs2: fix kernel bug at submit_bh_wbc()". This resolves a kernel BUG reported by syzbot. Since there are two flaws involved, I've made each one a separate patch. The first patch alone resolves the syzbot-reported bug, but I think both fixes should be sent to stable, so I've tagged them as such. This patch (of 2): Syzbot has reported a kernel bug in submit_bh_wbc() when writing file data to a nilfs2 file system whose metadata is corrupted. There are two flaws involved in this issue. The first flaw is that when nilfs_get_block() locates a data block using btree or direct mapping, if the disk address translation routine nilfs_dat_translate() fails with internal code -ENOENT due to DAT metadata corruption, it can be passed back to nilfs_get_block(). This causes nilfs_get_block() to misidentify an existing block as non-existent, causing both data block lookup and insertion to fail inconsistently. The second flaw is that nilfs_get_block() returns a successful status in this inconsistent state. This causes the caller __block_write_begin_int() or others to request a read even though the buffer is not mapped, resulting in a BUG_ON check for the BH_Mapped flag in submit_bh_wbc() failing. This fixes the first issue by changing the return value to code -EINVAL when a conversion using DAT fails with code -ENOENT, avoiding the conflicting condition that leads to the kernel bug described above. Here, code -EINVAL indicates that metadata corruption was detected during the block lookup, which will be properly handled as a file system error and converted to -EIO when passing through the nilfs2 bmap layer.

In the Linux kernel, the following vulnerability has been resolved: net/sched: taprio: proper TCA_TAPRIO_TC_ENTRY_INDEX check taprio_parse_tc_entry() is not correctly checking TCA_TAPRIO_TC_ENTRY_INDEX attribute: int tc; // Signed value tc = nla_get_u32(tb[TCA_TAPRIO_TC_ENTRY_INDEX]); if (tc >= TC_QOPT_MAX_QUEUE) { NL_SET_ERR_MSG_MOD(extack, "TC entry index out of range"); return -ERANGE; } syzbot reported that it could fed arbitary negative values: UBSAN: shift-out-of-bounds in net/sched/sch_taprio.c:1722:18 shift exponent -2147418108 is negative CPU: 0 PID: 5066 Comm: syz-executor367 Not tainted 6.8.0-rc7-syzkaller-00136-gc8a5c731fd12 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x1e7/0x2e0 lib/dump_stack.c:106 ubsan_epilogue lib/ubsan.c:217 [inline] __ubsan_handle_shift_out_of_bounds+0x3c7/0x420 lib/ubsan.c:386 taprio_parse_tc_entry net/sched/sch_taprio.c:1722 [inline] taprio_parse_tc_entries net/sched/sch_taprio.c:1768 [inline] taprio_change+0xb87/0x57d0 net/sched/sch_taprio.c:1877 taprio_init+0x9da/0xc80 net/sched/sch_taprio.c:2134 qdisc_create+0x9d4/0x1190 net/sched/sch_api.c:1355 tc_modify_qdisc+0xa26/0x1e40 net/sched/sch_api.c:1776 rtnetlink_rcv_msg+0x885/0x1040 net/core/rtnetlink.c:6617 netlink_rcv_skb+0x1e3/0x430 net/netlink/af_netlink.c:2543 netlink_unicast_kernel net/netlink/af_netlink.c:1341 [inline] netlink_unicast+0x7ea/0x980 net/netlink/af_netlink.c:1367 netlink_sendmsg+0xa3b/0xd70 net/netlink/af_netlink.c:1908 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x221/0x270 net/socket.c:745 ____sys_sendmsg+0x525/0x7d0 net/socket.c:2584 ___sys_sendmsg net/socket.c:2638 [inline] __sys_sendmsg+0x2b0/0x3a0 net/socket.c:2667 do_syscall_64+0xf9/0x240 entry_SYSCALL_64_after_hwframe+0x6f/0x77 RIP: 0033:0x7f1b2dea3759 Code: 48 83 c4 28 c3 e8 d7 19 00 00 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007ffd4de452f8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00007f1b2def0390 RCX: 00007f1b2dea3759 RDX: 0000000000000000 RSI: 00000000200007c0 RDI: 0000000000000004 RBP: 0000000000000003 R08: 0000555500000000 R09: 0000555500000000 R10: 0000555500000000 R11: 0000000000000246 R12: 00007ffd4de45340 R13: 00007ffd4de45310 R14: 0000000000000001 R15: 00007ffd4de45340

In the Linux kernel, the following vulnerability has been resolved: riscv: Sparse-Memory/vmemmap out-of-bounds fix Offset vmemmap so that the first page of vmemmap will be mapped to the first page of physical memory in order to ensure that vmemmap’s bounds will be respected during pfn_to_page()/page_to_pfn() operations. The conversion macros will produce correct SV39/48/57 addresses for every possible/valid DRAM_BASE inside the physical memory limits. v2:Address Alex's comments

In the Linux kernel, the following vulnerability has been resolved: net/smc: fix illegal rmb_desc access in SMC-D connection dump A crash was found when dumping SMC-D connections. It can be reproduced by following steps: - run nginx/wrk test: smc_run nginx smc_run wrk -t 16 -c 1000 -d <duration> -H 'Connection: Close' <URL> - continuously dump SMC-D connections in parallel: watch -n 1 'smcss -D' BUG: kernel NULL pointer dereference, address: 0000000000000030 CPU: 2 PID: 7204 Comm: smcss Kdump: loaded Tainted: G E 6.7.0+ #55 RIP: 0010:__smc_diag_dump.constprop.0+0x5e5/0x620 [smc_diag] Call Trace: <TASK> ? __die+0x24/0x70 ? page_fault_oops+0x66/0x150 ? exc_page_fault+0x69/0x140 ? asm_exc_page_fault+0x26/0x30 ? __smc_diag_dump.constprop.0+0x5e5/0x620 [smc_diag] ? __kmalloc_node_track_caller+0x35d/0x430 ? __alloc_skb+0x77/0x170 smc_diag_dump_proto+0xd0/0xf0 [smc_diag] smc_diag_dump+0x26/0x60 [smc_diag] netlink_dump+0x19f/0x320 __netlink_dump_start+0x1dc/0x300 smc_diag_handler_dump+0x6a/0x80 [smc_diag] ? __pfx_smc_diag_dump+0x10/0x10 [smc_diag] sock_diag_rcv_msg+0x121/0x140 ? __pfx_sock_diag_rcv_msg+0x10/0x10 netlink_rcv_skb+0x5a/0x110 sock_diag_rcv+0x28/0x40 netlink_unicast+0x22a/0x330 netlink_sendmsg+0x1f8/0x420 __sock_sendmsg+0xb0/0xc0 ____sys_sendmsg+0x24e/0x300 ? copy_msghdr_from_user+0x62/0x80 ___sys_sendmsg+0x7c/0xd0 ? __do_fault+0x34/0x160 ? do_read_fault+0x5f/0x100 ? do_fault+0xb0/0x110 ? __handle_mm_fault+0x2b0/0x6c0 __sys_sendmsg+0x4d/0x80 do_syscall_64+0x69/0x180 entry_SYSCALL_64_after_hwframe+0x6e/0x76 It is possible that the connection is in process of being established when we dump it. Assumed that the connection has been registered in a link group by smc_conn_create() but the rmb_desc has not yet been initialized by smc_buf_create(), thus causing the illegal access to conn->rmb_desc. So fix it by checking before dump.

In the Linux kernel, the following vulnerability has been resolved: drm/dp: Fix divide-by-zero regression on DP MST unplug with nouveau Fix a regression when using nouveau and unplugging a StarTech MSTDP122DP DisplayPort 1.2 MST hub (the same regression does not appear when using a Cable Matters DisplayPort 1.4 MST hub). Trace: divide error: 0000 [#1] PREEMPT SMP PTI CPU: 7 PID: 2962 Comm: Xorg Not tainted 6.8.0-rc3+ #744 Hardware name: Razer Blade/DANA_MB, BIOS 01.01 08/31/2018 RIP: 0010:drm_dp_bw_overhead+0xb4/0x110 [drm_display_helper] Code: c6 b8 01 00 00 00 75 61 01 c6 41 0f af f3 41 0f af f1 c1 e1 04 48 63 c7 31 d2 89 ff 48 8b 5d f8 c9 48 0f af f1 48 8d 44 06 ff <48> f7 f7 31 d2 31 c9 31 f6 31 ff 45 31 c0 45 31 c9 45 31 d2 45 31 RSP: 0018:ffffb2c5c211fa30 EFLAGS: 00010206 RAX: ffffffffffffffff RBX: 0000000000000000 RCX: 0000000000f59b00 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffffb2c5c211fa48 R08: 0000000000000001 R09: 0000000000000020 R10: 0000000000000004 R11: 0000000000000000 R12: 0000000000023b4a R13: ffff91d37d165800 R14: ffff91d36fac6d80 R15: ffff91d34a764010 FS: 00007f4a1ca3fa80(0000) GS:ffff91d6edbc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000559491d49000 CR3: 000000011d180002 CR4: 00000000003706f0 Call Trace: <TASK> ? show_regs+0x6d/0x80 ? die+0x37/0xa0 ? do_trap+0xd4/0xf0 ? do_error_trap+0x71/0xb0 ? drm_dp_bw_overhead+0xb4/0x110 [drm_display_helper] ? exc_divide_error+0x3a/0x70 ? drm_dp_bw_overhead+0xb4/0x110 [drm_display_helper] ? asm_exc_divide_error+0x1b/0x20 ? drm_dp_bw_overhead+0xb4/0x110 [drm_display_helper] ? drm_dp_calc_pbn_mode+0x2e/0x70 [drm_display_helper] nv50_msto_atomic_check+0xda/0x120 [nouveau] drm_atomic_helper_check_modeset+0xa87/0xdf0 [drm_kms_helper] drm_atomic_helper_check+0x19/0xa0 [drm_kms_helper] nv50_disp_atomic_check+0x13f/0x2f0 [nouveau] drm_atomic_check_only+0x668/0xb20 [drm] ? drm_connector_list_iter_next+0x86/0xc0 [drm] drm_atomic_commit+0x58/0xd0 [drm] ? __pfx___drm_printfn_info+0x10/0x10 [drm] drm_atomic_connector_commit_dpms+0xd7/0x100 [drm] drm_mode_obj_set_property_ioctl+0x1c5/0x450 [drm] ? __pfx_drm_connector_property_set_ioctl+0x10/0x10 [drm] drm_connector_property_set_ioctl+0x3b/0x60 [drm] drm_ioctl_kernel+0xb9/0x120 [drm] drm_ioctl+0x2d0/0x550 [drm] ? __pfx_drm_connector_property_set_ioctl+0x10/0x10 [drm] nouveau_drm_ioctl+0x61/0xc0 [nouveau] __x64_sys_ioctl+0xa0/0xf0 do_syscall_64+0x76/0x140 ? do_syscall_64+0x85/0x140 ? do_syscall_64+0x85/0x140 entry_SYSCALL_64_after_hwframe+0x6e/0x76 RIP: 0033:0x7f4a1cd1a94f Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <41> 89 c0 3d 00 f0 ff ff 77 1f 48 8b 44 24 18 64 48 2b 04 25 28 00 RSP: 002b:00007ffd2f1df520 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007ffd2f1df5b0 RCX: 00007f4a1cd1a94f RDX: 00007ffd2f1df5b0 RSI: 00000000c01064ab RDI: 000000000000000f RBP: 00000000c01064ab R08: 000056347932deb8 R09: 000056347a7d99c0 R10: 0000000000000000 R11: 0000000000000246 R12: 000056347938a220 R13: 000000000000000f R14: 0000563479d9f3f0 R15: 0000000000000000 </TASK> Modules linked in: rfcomm xt_conntrack nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlink nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xfrm_user xfrm_algo xt_addrtype nft_compat nf_tables nfnetlink br_netfilter bridge stp llc ccm cmac algif_hash overlay algif_skcipher af_alg bnep binfmt_misc snd_sof_pci_intel_cnl snd_sof_intel_hda_common snd_soc_hdac_hda snd_sof_pci snd_sof_xtensa_dsp snd_sof_intel_hda snd_sof snd_sof_utils snd_soc_acpi_intel_match snd_soc_acpi snd_soc_core snd_compress snd_sof_intel_hda_mlink snd_hda_ext_core iwlmvm intel_rapl_msr intel_rapl_common intel_tcc_cooling x86_pkg_temp_thermal intel_powerclamp mac80211 coretemp kvm_intel snd_hda_codec_hdmi kvm snd_hda_ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: net: atlantic: Fix DMA mapping for PTP hwts ring Function aq_ring_hwts_rx_alloc() maps extra AQ_CFG_RXDS_DEF bytes for PTP HWTS ring but then generic aq_ring_free() does not take this into account. Create and use a specific function to free HWTS ring to fix this issue. Trace: [ 215.351607] ------------[ cut here ]------------ [ 215.351612] DMA-API: atlantic 0000:4b:00.0: device driver frees DMA memory with different size [device address=0x00000000fbdd0000] [map size=34816 bytes] [unmap size=32768 bytes] [ 215.351635] WARNING: CPU: 33 PID: 10759 at kernel/dma/debug.c:988 check_unmap+0xa6f/0x2360 ... [ 215.581176] Call Trace: [ 215.583632] <TASK> [ 215.585745] ? show_trace_log_lvl+0x1c4/0x2df [ 215.590114] ? show_trace_log_lvl+0x1c4/0x2df [ 215.594497] ? debug_dma_free_coherent+0x196/0x210 [ 215.599305] ? check_unmap+0xa6f/0x2360 [ 215.603147] ? __warn+0xca/0x1d0 [ 215.606391] ? check_unmap+0xa6f/0x2360 [ 215.610237] ? report_bug+0x1ef/0x370 [ 215.613921] ? handle_bug+0x3c/0x70 [ 215.617423] ? exc_invalid_op+0x14/0x50 [ 215.621269] ? asm_exc_invalid_op+0x16/0x20 [ 215.625480] ? check_unmap+0xa6f/0x2360 [ 215.629331] ? mark_lock.part.0+0xca/0xa40 [ 215.633445] debug_dma_free_coherent+0x196/0x210 [ 215.638079] ? __pfx_debug_dma_free_coherent+0x10/0x10 [ 215.643242] ? slab_free_freelist_hook+0x11d/0x1d0 [ 215.648060] dma_free_attrs+0x6d/0x130 [ 215.651834] aq_ring_free+0x193/0x290 [atlantic] [ 215.656487] aq_ptp_ring_free+0x67/0x110 [atlantic] ... [ 216.127540] ---[ end trace 6467e5964dd2640b ]--- [ 216.132160] DMA-API: Mapped at: [ 216.132162] debug_dma_alloc_coherent+0x66/0x2f0 [ 216.132165] dma_alloc_attrs+0xf5/0x1b0 [ 216.132168] aq_ring_hwts_rx_alloc+0x150/0x1f0 [atlantic] [ 216.132193] aq_ptp_ring_alloc+0x1bb/0x540 [atlantic] [ 216.132213] aq_nic_init+0x4a1/0x760 [atlantic]

In the Linux kernel, the following vulnerability has been resolved: ipv6: fix potential "struct net" leak in inet6_rtm_getaddr() It seems that if userspace provides a correct IFA_TARGET_NETNSID value but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr() returns -EINVAL with an elevated "struct net" refcount.

In the Linux kernel, the following vulnerability has been resolved: inet: inet_defrag: prevent sk release while still in use ip_local_out() and other functions can pass skb->sk as function argument. If the skb is a fragment and reassembly happens before such function call returns, the sk must not be released. This affects skb fragments reassembled via netfilter or similar modules, e.g. openvswitch or ct_act.c, when run as part of tx pipeline. Eric Dumazet made an initial analysis of this bug. Quoting Eric: Calling ip_defrag() in output path is also implying skb_orphan(), which is buggy because output path relies on sk not disappearing. A relevant old patch about the issue was : 8282f27449bf ("inet: frag: Always orphan skbs inside ip_defrag()") [..] net/ipv4/ip_output.c depends on skb->sk being set, and probably to an inet socket, not an arbitrary one. If we orphan the packet in ipvlan, then downstream things like FQ packet scheduler will not work properly. We need to change ip_defrag() to only use skb_orphan() when really needed, ie whenever frag_list is going to be used. Eric suggested to stash sk in fragment queue and made an initial patch. However there is a problem with this: If skb is refragmented again right after, ip_do_fragment() will copy head->sk to the new fragments, and sets up destructor to sock_wfree. IOW, we have no choice but to fix up sk_wmem accouting to reflect the fully reassembled skb, else wmem will underflow. This change moves the orphan down into the core, to last possible moment. As ip_defrag_offset is aliased with sk_buff->sk member, we must move the offset into the FRAG_CB, else skb->sk gets clobbered. This allows to delay the orphaning long enough to learn if the skb has to be queued or if the skb is completing the reasm queue. In the former case, things work as before, skb is orphaned. This is safe because skb gets queued/stolen and won't continue past reasm engine. In the latter case, we will steal the skb->sk reference, reattach it to the head skb, and fix up wmem accouting when inet_frag inflates truesize.

In the Linux kernel, the following vulnerability has been resolved: dpll: fix possible deadlock during netlink dump operation Recently, I've been hitting following deadlock warning during dpll pin dump: [52804.637962] ====================================================== [52804.638536] WARNING: possible circular locking dependency detected [52804.639111] 6.8.0-rc2jiri+ #1 Not tainted [52804.639529] ------------------------------------------------------ [52804.640104] python3/2984 is trying to acquire lock: [52804.640581] ffff88810e642678 (nlk_cb_mutex-GENERIC){+.+.}-{3:3}, at: netlink_dump+0xb3/0x780 [52804.641417] but task is already holding lock: [52804.642010] ffffffff83bde4c8 (dpll_lock){+.+.}-{3:3}, at: dpll_lock_dumpit+0x13/0x20 [52804.642747] which lock already depends on the new lock. [52804.643551] the existing dependency chain (in reverse order) is: [52804.644259] -> #1 (dpll_lock){+.+.}-{3:3}: [52804.644836] lock_acquire+0x174/0x3e0 [52804.645271] __mutex_lock+0x119/0x1150 [52804.645723] dpll_lock_dumpit+0x13/0x20 [52804.646169] genl_start+0x266/0x320 [52804.646578] __netlink_dump_start+0x321/0x450 [52804.647056] genl_family_rcv_msg_dumpit+0x155/0x1e0 [52804.647575] genl_rcv_msg+0x1ed/0x3b0 [52804.648001] netlink_rcv_skb+0xdc/0x210 [52804.648440] genl_rcv+0x24/0x40 [52804.648831] netlink_unicast+0x2f1/0x490 [52804.649290] netlink_sendmsg+0x36d/0x660 [52804.649742] __sock_sendmsg+0x73/0xc0 [52804.650165] __sys_sendto+0x184/0x210 [52804.650597] __x64_sys_sendto+0x72/0x80 [52804.651045] do_syscall_64+0x6f/0x140 [52804.651474] entry_SYSCALL_64_after_hwframe+0x46/0x4e [52804.652001] -> #0 (nlk_cb_mutex-GENERIC){+.+.}-{3:3}: [52804.652650] check_prev_add+0x1ae/0x1280 [52804.653107] __lock_acquire+0x1ed3/0x29a0 [52804.653559] lock_acquire+0x174/0x3e0 [52804.653984] __mutex_lock+0x119/0x1150 [52804.654423] netlink_dump+0xb3/0x780 [52804.654845] __netlink_dump_start+0x389/0x450 [52804.655321] genl_family_rcv_msg_dumpit+0x155/0x1e0 [52804.655842] genl_rcv_msg+0x1ed/0x3b0 [52804.656272] netlink_rcv_skb+0xdc/0x210 [52804.656721] genl_rcv+0x24/0x40 [52804.657119] netlink_unicast+0x2f1/0x490 [52804.657570] netlink_sendmsg+0x36d/0x660 [52804.658022] __sock_sendmsg+0x73/0xc0 [52804.658450] __sys_sendto+0x184/0x210 [52804.658877] __x64_sys_sendto+0x72/0x80 [52804.659322] do_syscall_64+0x6f/0x140 [52804.659752] entry_SYSCALL_64_after_hwframe+0x46/0x4e [52804.660281] other info that might help us debug this: [52804.661077] Possible unsafe locking scenario: [52804.661671] CPU0 CPU1 [52804.662129] ---- ---- [52804.662577] lock(dpll_lock); [52804.662924] lock(nlk_cb_mutex-GENERIC); [52804.663538] lock(dpll_lock); [52804.664073] lock(nlk_cb_mutex-GENERIC); [52804.664490] The issue as follows: __netlink_dump_start() calls control->start(cb) with nlk->cb_mutex held. In control->start(cb) the dpll_lock is taken. Then nlk->cb_mutex is released and taken again in netlink_dump(), while dpll_lock still being held. That leads to ABBA deadlock when another CPU races with the same operation. Fix this by moving dpll_lock taking into dumpit() callback which ensures correct lock taking order.

In the Linux kernel, the following vulnerability has been resolved: scsi: core: Move scsi_host_busy() out of host lock for waking up EH handler Inside scsi_eh_wakeup(), scsi_host_busy() is called & checked with host lock every time for deciding if error handler kthread needs to be waken up. This can be too heavy in case of recovery, such as: - N hardware queues - queue depth is M for each hardware queue - each scsi_host_busy() iterates over (N * M) tag/requests If recovery is triggered in case that all requests are in-flight, each scsi_eh_wakeup() is strictly serialized, when scsi_eh_wakeup() is called for the last in-flight request, scsi_host_busy() has been run for (N * M - 1) times, and request has been iterated for (N*M - 1) * (N * M) times. If both N and M are big enough, hard lockup can be triggered on acquiring host lock, and it is observed on mpi3mr(128 hw queues, queue depth 8169). Fix the issue by calling scsi_host_busy() outside the host lock. We don't need the host lock for getting busy count because host the lock never covers that. [mkp: Drop unnecessary 'busy' variables pointed out by Bart]

In the Linux kernel, the following vulnerability has been resolved: RDMA/srpt: Support specifying the srpt_service_guid parameter Make loading ib_srpt with this parameter set work. The current behavior is that setting that parameter while loading the ib_srpt kernel module triggers the following kernel crash: BUG: kernel NULL pointer dereference, address: 0000000000000000 Call Trace: <TASK> parse_one+0x18c/0x1d0 parse_args+0xe1/0x230 load_module+0x8de/0xa60 init_module_from_file+0x8b/0xd0 idempotent_init_module+0x181/0x240 __x64_sys_finit_module+0x5a/0xb0 do_syscall_64+0x5f/0xe0 entry_SYSCALL_64_after_hwframe+0x6e/0x76

In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress basechain Remove netdevice from inet/ingress basechain in case NETDEV_UNREGISTER event is reported, otherwise a stale reference to netdevice remains in the hook list.

In the Linux kernel, the following vulnerability has been resolved: drm/i915/gt: Reset queue_priority_hint on parking Originally, with strict in order execution, we could complete execution only when the queue was empty. Preempt-to-busy allows replacement of an active request that may complete before the preemption is processed by HW. If that happens, the request is retired from the queue, but the queue_priority_hint remains set, preventing direct submission until after the next CS interrupt is processed. This preempt-to-busy race can be triggered by the heartbeat, which will also act as the power-management barrier and upon completion allow us to idle the HW. We may process the completion of the heartbeat, and begin parking the engine before the CS event that restores the queue_priority_hint, causing us to fail the assertion that it is MIN. <3>[ 166.210729] __engine_park:283 GEM_BUG_ON(engine->sched_engine->queue_priority_hint != (-((int)(~0U >> 1)) - 1)) <0>[ 166.210781] Dumping ftrace buffer: <0>[ 166.210795] --------------------------------- ... <0>[ 167.302811] drm_fdin-1097 2..s1. 165741070us : trace_ports: 0000:00:02.0 rcs0: promote { ccid:20 1217:2 prio 0 } <0>[ 167.302861] drm_fdin-1097 2d.s2. 165741072us : execlists_submission_tasklet: 0000:00:02.0 rcs0: preempting last=1217:2, prio=0, hint=2147483646 <0>[ 167.302928] drm_fdin-1097 2d.s2. 165741072us : __i915_request_unsubmit: 0000:00:02.0 rcs0: fence 1217:2, current 0 <0>[ 167.302992] drm_fdin-1097 2d.s2. 165741073us : __i915_request_submit: 0000:00:02.0 rcs0: fence 3:4660, current 4659 <0>[ 167.303044] drm_fdin-1097 2d.s1. 165741076us : execlists_submission_tasklet: 0000:00:02.0 rcs0: context:3 schedule-in, ccid:40 <0>[ 167.303095] drm_fdin-1097 2d.s1. 165741077us : trace_ports: 0000:00:02.0 rcs0: submit { ccid:40 3:4660* prio 2147483646 } <0>[ 167.303159] kworker/-89 11..... 165741139us : i915_request_retire.part.0: 0000:00:02.0 rcs0: fence c90:2, current 2 <0>[ 167.303208] kworker/-89 11..... 165741148us : __intel_context_do_unpin: 0000:00:02.0 rcs0: context:c90 unpin <0>[ 167.303272] kworker/-89 11..... 165741159us : i915_request_retire.part.0: 0000:00:02.0 rcs0: fence 1217:2, current 2 <0>[ 167.303321] kworker/-89 11..... 165741166us : __intel_context_do_unpin: 0000:00:02.0 rcs0: context:1217 unpin <0>[ 167.303384] kworker/-89 11..... 165741170us : i915_request_retire.part.0: 0000:00:02.0 rcs0: fence 3:4660, current 4660 <0>[ 167.303434] kworker/-89 11d..1. 165741172us : __intel_context_retire: 0000:00:02.0 rcs0: context:1216 retire runtime: { total:56028ns, avg:56028ns } <0>[ 167.303484] kworker/-89 11..... 165741198us : __engine_park: 0000:00:02.0 rcs0: parked <0>[ 167.303534] <idle>-0 5d.H3. 165741207us : execlists_irq_handler: 0000:00:02.0 rcs0: semaphore yield: 00000040 <0>[ 167.303583] kworker/-89 11..... 165741397us : __intel_context_retire: 0000:00:02.0 rcs0: context:1217 retire runtime: { total:325575ns, avg:0ns } <0>[ 167.303756] kworker/-89 11..... 165741777us : __intel_context_retire: 0000:00:02.0 rcs0: context:c90 retire runtime: { total:0ns, avg:0ns } <0>[ 167.303806] kworker/-89 11..... 165742017us : __engine_park: __engine_park:283 GEM_BUG_ON(engine->sched_engine->queue_priority_hint != (-((int)(~0U >> 1)) - 1)) <0>[ 167.303811] --------------------------------- <4>[ 167.304722] ------------[ cut here ]------------ <2>[ 167.304725] kernel BUG at drivers/gpu/drm/i915/gt/intel_engine_pm.c:283! <4>[ 167.304731] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI <4>[ 167.304734] CPU: 11 PID: 89 Comm: kworker/11:1 Tainted: G W 6.8.0-rc2-CI_DRM_14193-gc655e0fd2804+ #1 <4>[ 167.304736] Hardware name: Intel Corporation Rocket Lake Client Platform/RocketLake S UDIMM 6L RVP, BIOS RKLSFWI1.R00.3173.A03.2204210138 04/21/2022 <4>[ 167.304738] Workqueue: i915-unordered retire_work_handler [i915] <4>[ 16 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix memory leak in dm_sw_fini() After destroying dmub_srv, the memory associated with it is not freed, causing a memory leak: unreferenced object 0xffff896302b45800 (size 1024): comm "(udev-worker)", pid 222, jiffies 4294894636 hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace (crc 6265fd77): [<ffffffff993495ed>] kmalloc_trace+0x29d/0x340 [<ffffffffc0ea4a94>] dm_dmub_sw_init+0xb4/0x450 [amdgpu] [<ffffffffc0ea4e55>] dm_sw_init+0x15/0x2b0 [amdgpu] [<ffffffffc0ba8557>] amdgpu_device_init+0x1417/0x24e0 [amdgpu] [<ffffffffc0bab285>] amdgpu_driver_load_kms+0x15/0x190 [amdgpu] [<ffffffffc0ba09c7>] amdgpu_pci_probe+0x187/0x4e0 [amdgpu] [<ffffffff9968fd1e>] local_pci_probe+0x3e/0x90 [<ffffffff996918a3>] pci_device_probe+0xc3/0x230 [<ffffffff99805872>] really_probe+0xe2/0x480 [<ffffffff99805c98>] __driver_probe_device+0x78/0x160 [<ffffffff99805daf>] driver_probe_device+0x1f/0x90 [<ffffffff9980601e>] __driver_attach+0xce/0x1c0 [<ffffffff99803170>] bus_for_each_dev+0x70/0xc0 [<ffffffff99804822>] bus_add_driver+0x112/0x210 [<ffffffff99807245>] driver_register+0x55/0x100 [<ffffffff990012d1>] do_one_initcall+0x41/0x300 Fix this by freeing dmub_srv after destroying it.

In the Linux kernel, the following vulnerability has been resolved: af_unix: Fix task hung while purging oob_skb in GC. syzbot reported a task hung; at the same time, GC was looping infinitely in list_for_each_entry_safe() for OOB skb. [0] syzbot demonstrated that the list_for_each_entry_safe() was not actually safe in this case. A single skb could have references for multiple sockets. If we free such a skb in the list_for_each_entry_safe(), the current and next sockets could be unlinked in a single iteration. unix_notinflight() uses list_del_init() to unlink the socket, so the prefetched next socket forms a loop itself and list_for_each_entry_safe() never stops. Here, we must use while() and make sure we always fetch the first socket. [0]: Sending NMI from CPU 0 to CPUs 1: NMI backtrace for cpu 1 CPU: 1 PID: 5065 Comm: syz-executor236 Not tainted 6.8.0-rc3-syzkaller-00136-g1f719a2f3fa6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/25/2024 RIP: 0010:preempt_count arch/x86/include/asm/preempt.h:26 [inline] RIP: 0010:check_kcov_mode kernel/kcov.c:173 [inline] RIP: 0010:__sanitizer_cov_trace_pc+0xd/0x60 kernel/kcov.c:207 Code: cc cc cc cc 66 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 65 48 8b 14 25 40 c2 03 00 <65> 8b 05 b4 7c 78 7e a9 00 01 ff 00 48 8b 34 24 74 0f f6 c4 01 74 RSP: 0018:ffffc900033efa58 EFLAGS: 00000283 RAX: ffff88807b077800 RBX: ffff88807b077800 RCX: 1ffffffff27b1189 RDX: ffff88802a5a3b80 RSI: ffffffff8968488d RDI: ffff88807b077f70 RBP: ffffc900033efbb0 R08: 0000000000000001 R09: fffffbfff27a900c R10: ffffffff93d48067 R11: ffffffff8ae000eb R12: ffff88807b077800 R13: dffffc0000000000 R14: ffff88807b077e40 R15: 0000000000000001 FS: 0000000000000000(0000) GS:ffff8880b9500000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000564f4fc1e3a8 CR3: 000000000d57a000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <NMI> </NMI> <TASK> unix_gc+0x563/0x13b0 net/unix/garbage.c:319 unix_release_sock+0xa93/0xf80 net/unix/af_unix.c:683 unix_release+0x91/0xf0 net/unix/af_unix.c:1064 __sock_release+0xb0/0x270 net/socket.c:659 sock_close+0x1c/0x30 net/socket.c:1421 __fput+0x270/0xb80 fs/file_table.c:376 task_work_run+0x14f/0x250 kernel/task_work.c:180 exit_task_work include/linux/task_work.h:38 [inline] do_exit+0xa8a/0x2ad0 kernel/exit.c:871 do_group_exit+0xd4/0x2a0 kernel/exit.c:1020 __do_sys_exit_group kernel/exit.c:1031 [inline] __se_sys_exit_group kernel/exit.c:1029 [inline] __x64_sys_exit_group+0x3e/0x50 kernel/exit.c:1029 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xd5/0x270 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x6f/0x77 RIP: 0033:0x7f9d6cbdac09 Code: Unable to access opcode bytes at 0x7f9d6cbdabdf. RSP: 002b:00007fff5952feb8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f9d6cbdac09 RDX: 000000000000003c RSI: 00000000000000e7 RDI: 0000000000000000 RBP: 00007f9d6cc552b0 R08: ffffffffffffffb8 R09: 0000000000000006 R10: 0000000000000006 R11: 0000000000000246 R12: 00007f9d6cc552b0 R13: 0000000000000000 R14: 00007f9d6cc55d00 R15: 00007f9d6cbabe70 </TASK>

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: fix null-pointer dereference on edid reading Use i2c adapter when there isn't aux_mode in dc_link to fix a null-pointer derefence that happens when running igt@kms_force_connector_basic in a system with DCN2.1 and HDMI connector detected as below: [ +0.178146] BUG: kernel NULL pointer dereference, address: 00000000000004c0 [ +0.000010] #PF: supervisor read access in kernel mode [ +0.000005] #PF: error_code(0x0000) - not-present page [ +0.000004] PGD 0 P4D 0 [ +0.000006] Oops: 0000 [#1] PREEMPT SMP NOPTI [ +0.000006] CPU: 15 PID: 2368 Comm: kms_force_conne Not tainted 6.5.0-asdn+ #152 [ +0.000005] Hardware name: HP HP ENVY x360 Convertible 13-ay1xxx/8929, BIOS F.01 07/14/2021 [ +0.000004] RIP: 0010:i2c_transfer+0xd/0x100 [ +0.000011] Code: ea fc ff ff 66 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 0f 1f 44 00 00 41 54 55 53 <48> 8b 47 10 48 89 fb 48 83 38 00 0f 84 b3 00 00 00 83 3d 2f 80 16 [ +0.000004] RSP: 0018:ffff9c4f89c0fad0 EFLAGS: 00010246 [ +0.000005] RAX: 0000000000000000 RBX: 0000000000000005 RCX: 0000000000000080 [ +0.000003] RDX: 0000000000000002 RSI: ffff9c4f89c0fb20 RDI: 00000000000004b0 [ +0.000003] RBP: ffff9c4f89c0fb80 R08: 0000000000000080 R09: ffff8d8e0b15b980 [ +0.000003] R10: 00000000000380e0 R11: 0000000000000000 R12: 0000000000000080 [ +0.000002] R13: 0000000000000002 R14: ffff9c4f89c0fb0e R15: ffff9c4f89c0fb0f [ +0.000004] FS: 00007f9ad2176c40(0000) GS:ffff8d90fe9c0000(0000) knlGS:0000000000000000 [ +0.000003] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ +0.000004] CR2: 00000000000004c0 CR3: 0000000121bc4000 CR4: 0000000000750ee0 [ +0.000003] PKRU: 55555554 [ +0.000003] Call Trace: [ +0.000006] <TASK> [ +0.000006] ? __die+0x23/0x70 [ +0.000011] ? page_fault_oops+0x17d/0x4c0 [ +0.000008] ? preempt_count_add+0x6e/0xa0 [ +0.000008] ? srso_alias_return_thunk+0x5/0x7f [ +0.000011] ? exc_page_fault+0x7f/0x180 [ +0.000009] ? asm_exc_page_fault+0x26/0x30 [ +0.000013] ? i2c_transfer+0xd/0x100 [ +0.000010] drm_do_probe_ddc_edid+0xc2/0x140 [drm] [ +0.000067] ? srso_alias_return_thunk+0x5/0x7f [ +0.000006] ? _drm_do_get_edid+0x97/0x3c0 [drm] [ +0.000043] ? __pfx_drm_do_probe_ddc_edid+0x10/0x10 [drm] [ +0.000042] edid_block_read+0x3b/0xd0 [drm] [ +0.000043] _drm_do_get_edid+0xb6/0x3c0 [drm] [ +0.000041] ? __pfx_drm_do_probe_ddc_edid+0x10/0x10 [drm] [ +0.000043] drm_edid_read_custom+0x37/0xd0 [drm] [ +0.000044] amdgpu_dm_connector_mode_valid+0x129/0x1d0 [amdgpu] [ +0.000153] drm_connector_mode_valid+0x3b/0x60 [drm_kms_helper] [ +0.000000] __drm_helper_update_and_validate+0xfe/0x3c0 [drm_kms_helper] [ +0.000000] ? amdgpu_dm_connector_get_modes+0xb6/0x520 [amdgpu] [ +0.000000] ? srso_alias_return_thunk+0x5/0x7f [ +0.000000] drm_helper_probe_single_connector_modes+0x2ab/0x540 [drm_kms_helper] [ +0.000000] status_store+0xb2/0x1f0 [drm] [ +0.000000] kernfs_fop_write_iter+0x136/0x1d0 [ +0.000000] vfs_write+0x24d/0x440 [ +0.000000] ksys_write+0x6f/0xf0 [ +0.000000] do_syscall_64+0x60/0xc0 [ +0.000000] ? srso_alias_return_thunk+0x5/0x7f [ +0.000000] ? syscall_exit_to_user_mode+0x2b/0x40 [ +0.000000] ? srso_alias_return_thunk+0x5/0x7f [ +0.000000] ? do_syscall_64+0x6c/0xc0 [ +0.000000] ? do_syscall_64+0x6c/0xc0 [ +0.000000] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 [ +0.000000] RIP: 0033:0x7f9ad46b4b00 [ +0.000000] Code: 40 00 48 8b 15 19 b3 0d 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 80 3d e1 3a 0e 00 00 74 17 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 48 83 ec 28 48 89 [ +0.000000] RSP: 002b:00007ffcbd3bd6d8 EFLAGS: 00000202 ORIG_RAX: 0000000000000001 [ +0.000000] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f9ad46b4b00 [ +0.000000] RDX: 0000000000000002 RSI: 00007f9ad48a7417 RDI: 0000000000000009 [ +0.000000] RBP: 0000000000000002 R08 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: md: Don't ignore suspended array in md_check_recovery() mddev_suspend() never stop sync_thread, hence it doesn't make sense to ignore suspended array in md_check_recovery(), which might cause sync_thread can't be unregistered. After commit f52f5c71f3d4 ("md: fix stopping sync thread"), following hang can be triggered by test shell/integrity-caching.sh: 1) suspend the array: raid_postsuspend mddev_suspend 2) stop the array: raid_dtr md_stop __md_stop_writes stop_sync_thread set_bit(MD_RECOVERY_INTR, &mddev->recovery); md_wakeup_thread_directly(mddev->sync_thread); wait_event(..., !test_bit(MD_RECOVERY_RUNNING, &mddev->recovery)) 3) sync thread done: md_do_sync set_bit(MD_RECOVERY_DONE, &mddev->recovery); md_wakeup_thread(mddev->thread); 4) daemon thread can't unregister sync thread: md_check_recovery if (mddev->suspended) return; -> return directly md_read_sync_thread clear_bit(MD_RECOVERY_RUNNING, &mddev->recovery); -> MD_RECOVERY_RUNNING can't be cleared, hence step 2 hang; This problem is not just related to dm-raid, fix it by ignoring suspended array in md_check_recovery(). And follow up patches will improve dm-raid better to frozen sync thread during suspend.

In the Linux kernel, the following vulnerability has been resolved: serial: core: Clearing the circular buffer before NULLifying it The circular buffer is NULLified in uart_tty_port_shutdown() under the spin lock. However, the PM or other timer based callbacks may still trigger after this event without knowning that buffer pointer is not valid. Since the serial code is a bit inconsistent in checking the buffer state (some rely on the head-tail positions, some on the buffer pointer), it's better to have both aligned, i.e. buffer pointer to be NULL and head-tail possitions to be the same, meaning it's empty. This will prevent asynchronous calls to dereference NULL pointer as reported recently in 8250 case: BUG: kernel NULL pointer dereference, address: 00000cf5 Workqueue: pm pm_runtime_work EIP: serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809) ... ? serial8250_tx_chars (drivers/tty/serial/8250/8250_port.c:1809) __start_tx (drivers/tty/serial/8250/8250_port.c:1551) serial8250_start_tx (drivers/tty/serial/8250/8250_port.c:1654) serial_port_runtime_suspend (include/linux/serial_core.h:667 drivers/tty/serial/serial_port.c:63) __rpm_callback (drivers/base/power/runtime.c:393) ? serial_port_remove (drivers/tty/serial/serial_port.c:50) rpm_suspend (drivers/base/power/runtime.c:447) The proposed change will prevent ->start_tx() to be called during suspend on shut down port.

A memory leak flaw was found in the UBI driver in drivers/mtd/ubi/attach.c in the Linux kernel through 6.7.4 for UBI_IOCATT, because kobj->name is not released.