In the Linux kernel, the following vulnerability has been resolved: scsi: hisi_sas: Fix a deadlock issue related to automatic dump If we issue a disabling PHY command, the device attached with it will go offline, if a 2 bit ECC error occurs at the same time, a hung task may be found: [ 4613.652388] INFO: task kworker/u256:0:165233 blocked for more than 120 seconds. [ 4613.666297] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 4613.674809] task:kworker/u256:0 state:D stack: 0 pid:165233 ppid: 2 flags:0x00000208 [ 4613.683959] Workqueue: 0000:74:02.0_disco_q sas_revalidate_domain [libsas] [ 4613.691518] Call trace: [ 4613.694678] __switch_to+0xf8/0x17c [ 4613.698872] __schedule+0x660/0xee0 [ 4613.703063] schedule+0xac/0x240 [ 4613.706994] schedule_timeout+0x500/0x610 [ 4613.711705] __down+0x128/0x36c [ 4613.715548] down+0x240/0x2d0 [ 4613.719221] hisi_sas_internal_abort_timeout+0x1bc/0x260 [hisi_sas_main] [ 4613.726618] sas_execute_internal_abort+0x144/0x310 [libsas] [ 4613.732976] sas_execute_internal_abort_dev+0x44/0x60 [libsas] [ 4613.739504] hisi_sas_internal_task_abort_dev.isra.0+0xbc/0x1b0 [hisi_sas_main] [ 4613.747499] hisi_sas_dev_gone+0x174/0x250 [hisi_sas_main] [ 4613.753682] sas_notify_lldd_dev_gone+0xec/0x2e0 [libsas] [ 4613.759781] sas_unregister_common_dev+0x4c/0x7a0 [libsas] [ 4613.765962] sas_destruct_devices+0xb8/0x120 [libsas] [ 4613.771709] sas_do_revalidate_domain.constprop.0+0x1b8/0x31c [libsas] [ 4613.778930] sas_revalidate_domain+0x60/0xa4 [libsas] [ 4613.784716] process_one_work+0x248/0x950 [ 4613.789424] worker_thread+0x318/0x934 [ 4613.793878] kthread+0x190/0x200 [ 4613.797810] ret_from_fork+0x10/0x18 [ 4613.802121] INFO: task kworker/u256:4:316722 blocked for more than 120 seconds. [ 4613.816026] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 4613.824538] task:kworker/u256:4 state:D stack: 0 pid:316722 ppid: 2 flags:0x00000208 [ 4613.833670] Workqueue: 0000:74:02.0 hisi_sas_rst_work_handler [hisi_sas_main] [ 4613.841491] Call trace: [ 4613.844647] __switch_to+0xf8/0x17c [ 4613.848852] __schedule+0x660/0xee0 [ 4613.853052] schedule+0xac/0x240 [ 4613.856984] schedule_timeout+0x500/0x610 [ 4613.861695] __down+0x128/0x36c [ 4613.865542] down+0x240/0x2d0 [ 4613.869216] hisi_sas_controller_prereset+0x58/0x1fc [hisi_sas_main] [ 4613.876324] hisi_sas_rst_work_handler+0x40/0x8c [hisi_sas_main] [ 4613.883019] process_one_work+0x248/0x950 [ 4613.887732] worker_thread+0x318/0x934 [ 4613.892204] kthread+0x190/0x200 [ 4613.896118] ret_from_fork+0x10/0x18 [ 4613.900423] INFO: task kworker/u256:1:348985 blocked for more than 121 seconds. [ 4613.914341] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 4613.922852] task:kworker/u256:1 state:D stack: 0 pid:348985 ppid: 2 flags:0x00000208 [ 4613.931984] Workqueue: 0000:74:02.0_event_q sas_port_event_worker [libsas] [ 4613.939549] Call trace: [ 4613.942702] __switch_to+0xf8/0x17c [ 4613.946892] __schedule+0x660/0xee0 [ 4613.951083] schedule+0xac/0x240 [ 4613.955015] schedule_timeout+0x500/0x610 [ 4613.959725] wait_for_common+0x200/0x610 [ 4613.964349] wait_for_completion+0x3c/0x5c [ 4613.969146] flush_workqueue+0x198/0x790 [ 4613.973776] sas_porte_broadcast_rcvd+0x1e8/0x320 [libsas] [ 4613.979960] sas_port_event_worker+0x54/0xa0 [libsas] [ 4613.985708] process_one_work+0x248/0x950 [ 4613.990420] worker_thread+0x318/0x934 [ 4613.994868] kthread+0x190/0x200 [ 4613.998800] ret_from_fork+0x10/0x18 This is because when the device goes offline, we obtain the hisi_hba semaphore and send the ABORT_DEV command to the device. However, the internal abort timed out due to the 2 bit ECC error and triggers automatic dump. In addition, since the hisi_hba semaphore has been obtained, the dump cannot be executed and the controller cannot be reset. Therefore, the deadlocks occur on the following circular dependencies ---truncated---

Insufficient validation of the IOCTL (Input Output Control) input buffer in AMD μProf may allow an authenticated user to send an arbitrary buffer potentially resulting in a Windows crash leading to denial of service.

In the Linux kernel, the following vulnerability has been resolved: bpf: make sure skb->len != 0 when redirecting to a tunneling device syzkaller managed to trigger another case where skb->len == 0 when we enter __dev_queue_xmit: WARNING: CPU: 0 PID: 2470 at include/linux/skbuff.h:2576 skb_assert_len include/linux/skbuff.h:2576 [inline] WARNING: CPU: 0 PID: 2470 at include/linux/skbuff.h:2576 __dev_queue_xmit+0x2069/0x35e0 net/core/dev.c:4295 Call Trace: dev_queue_xmit+0x17/0x20 net/core/dev.c:4406 __bpf_tx_skb net/core/filter.c:2115 [inline] __bpf_redirect_no_mac net/core/filter.c:2140 [inline] __bpf_redirect+0x5fb/0xda0 net/core/filter.c:2163 ____bpf_clone_redirect net/core/filter.c:2447 [inline] bpf_clone_redirect+0x247/0x390 net/core/filter.c:2419 bpf_prog_48159a89cb4a9a16+0x59/0x5e bpf_dispatcher_nop_func include/linux/bpf.h:897 [inline] __bpf_prog_run include/linux/filter.h:596 [inline] bpf_prog_run include/linux/filter.h:603 [inline] bpf_test_run+0x46c/0x890 net/bpf/test_run.c:402 bpf_prog_test_run_skb+0xbdc/0x14c0 net/bpf/test_run.c:1170 bpf_prog_test_run+0x345/0x3c0 kernel/bpf/syscall.c:3648 __sys_bpf+0x43a/0x6c0 kernel/bpf/syscall.c:5005 __do_sys_bpf kernel/bpf/syscall.c:5091 [inline] __se_sys_bpf kernel/bpf/syscall.c:5089 [inline] __x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:5089 do_syscall_64+0x54/0x70 arch/x86/entry/common.c:48 entry_SYSCALL_64_after_hwframe+0x61/0xc6 The reproducer doesn't really reproduce outside of syzkaller environment, so I'm taking a guess here. It looks like we do generate correct ETH_HLEN-sized packet, but we redirect the packet to the tunneling device. Before we do so, we __skb_pull l2 header and arrive again at skb->len == 0. Doesn't seem like we can do anything better than having an explicit check after __skb_pull?

A memory leak flaw and potential divide by zero and Integer overflow was found in the Linux kernel V4L2 and vivid test code functionality. This issue occurs when a user triggers ioctls, such as VIDIOC_S_DV_TIMINGS ioctl. This could allow a local user to crash the system if vivid test code enabled.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Forcibly leave nested virt when SMM state is toggled Forcibly leave nested virtualization operation if userspace toggles SMM state via KVM_SET_VCPU_EVENTS or KVM_SYNC_X86_EVENTS. If userspace forces the vCPU out of SMM while it's post-VMXON and then injects an SMI, vmx_enter_smm() will overwrite vmx->nested.smm.vmxon and end up with both vmxon=false and smm.vmxon=false, but all other nVMX state allocated. Don't attempt to gracefully handle the transition as (a) most transitions are nonsencial, e.g. forcing SMM while L2 is running, (b) there isn't sufficient information to handle all transitions, e.g. SVM wants access to the SMRAM save state, and (c) KVM_SET_VCPU_EVENTS must precede KVM_SET_NESTED_STATE during state restore as the latter disallows putting the vCPU into L2 if SMM is active, and disallows tagging the vCPU as being post-VMXON in SMM if SMM is not active. Abuse of KVM_SET_VCPU_EVENTS manifests as a WARN and memory leak in nVMX due to failure to free vmcs01's shadow VMCS, but the bug goes far beyond just a memory leak, e.g. toggling SMM on while L2 is active puts the vCPU in an architecturally impossible state. WARNING: CPU: 0 PID: 3606 at free_loaded_vmcs arch/x86/kvm/vmx/vmx.c:2665 [inline] WARNING: CPU: 0 PID: 3606 at free_loaded_vmcs+0x158/0x1a0 arch/x86/kvm/vmx/vmx.c:2656 Modules linked in: CPU: 1 PID: 3606 Comm: syz-executor725 Not tainted 5.17.0-rc1-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:free_loaded_vmcs arch/x86/kvm/vmx/vmx.c:2665 [inline] RIP: 0010:free_loaded_vmcs+0x158/0x1a0 arch/x86/kvm/vmx/vmx.c:2656 Code: <0f> 0b eb b3 e8 8f 4d 9f 00 e9 f7 fe ff ff 48 89 df e8 92 4d 9f 00 Call Trace: <TASK> kvm_arch_vcpu_destroy+0x72/0x2f0 arch/x86/kvm/x86.c:11123 kvm_vcpu_destroy arch/x86/kvm/../../../virt/kvm/kvm_main.c:441 [inline] kvm_destroy_vcpus+0x11f/0x290 arch/x86/kvm/../../../virt/kvm/kvm_main.c:460 kvm_free_vcpus arch/x86/kvm/x86.c:11564 [inline] kvm_arch_destroy_vm+0x2e8/0x470 arch/x86/kvm/x86.c:11676 kvm_destroy_vm arch/x86/kvm/../../../virt/kvm/kvm_main.c:1217 [inline] kvm_put_kvm+0x4fa/0xb00 arch/x86/kvm/../../../virt/kvm/kvm_main.c:1250 kvm_vm_release+0x3f/0x50 arch/x86/kvm/../../../virt/kvm/kvm_main.c:1273 __fput+0x286/0x9f0 fs/file_table.c:311 task_work_run+0xdd/0x1a0 kernel/task_work.c:164 exit_task_work include/linux/task_work.h:32 [inline] do_exit+0xb29/0x2a30 kernel/exit.c:806 do_group_exit+0xd2/0x2f0 kernel/exit.c:935 get_signal+0x4b0/0x28c0 kernel/signal.c:2862 arch_do_signal_or_restart+0x2a9/0x1c40 arch/x86/kernel/signal.c:868 handle_signal_work kernel/entry/common.c:148 [inline] exit_to_user_mode_loop kernel/entry/common.c:172 [inline] exit_to_user_mode_prepare+0x17d/0x290 kernel/entry/common.c:207 __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline] syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300 do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86 entry_SYSCALL_64_after_hwframe+0x44/0xae </TASK>

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix hang during unmount when stopping a space reclaim worker Often when running generic/562 from fstests we can hang during unmount, resulting in a trace like this: Sep 07 11:52:00 debian9 unknown: run fstests generic/562 at 2022-09-07 11:52:00 Sep 07 11:55:32 debian9 kernel: INFO: task umount:49438 blocked for more than 120 seconds. Sep 07 11:55:32 debian9 kernel: Not tainted 6.0.0-rc2-btrfs-next-122 #1 Sep 07 11:55:32 debian9 kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Sep 07 11:55:32 debian9 kernel: task:umount state:D stack: 0 pid:49438 ppid: 25683 flags:0x00004000 Sep 07 11:55:32 debian9 kernel: Call Trace: Sep 07 11:55:32 debian9 kernel: <TASK> Sep 07 11:55:32 debian9 kernel: __schedule+0x3c8/0xec0 Sep 07 11:55:32 debian9 kernel: ? rcu_read_lock_sched_held+0x12/0x70 Sep 07 11:55:32 debian9 kernel: schedule+0x5d/0xf0 Sep 07 11:55:32 debian9 kernel: schedule_timeout+0xf1/0x130 Sep 07 11:55:32 debian9 kernel: ? lock_release+0x224/0x4a0 Sep 07 11:55:32 debian9 kernel: ? lock_acquired+0x1a0/0x420 Sep 07 11:55:32 debian9 kernel: ? trace_hardirqs_on+0x2c/0xd0 Sep 07 11:55:32 debian9 kernel: __wait_for_common+0xac/0x200 Sep 07 11:55:32 debian9 kernel: ? usleep_range_state+0xb0/0xb0 Sep 07 11:55:32 debian9 kernel: __flush_work+0x26d/0x530 Sep 07 11:55:32 debian9 kernel: ? flush_workqueue_prep_pwqs+0x140/0x140 Sep 07 11:55:32 debian9 kernel: ? trace_clock_local+0xc/0x30 Sep 07 11:55:32 debian9 kernel: __cancel_work_timer+0x11f/0x1b0 Sep 07 11:55:32 debian9 kernel: ? close_ctree+0x12b/0x5b3 [btrfs] Sep 07 11:55:32 debian9 kernel: ? __trace_bputs+0x10b/0x170 Sep 07 11:55:32 debian9 kernel: close_ctree+0x152/0x5b3 [btrfs] Sep 07 11:55:32 debian9 kernel: ? evict_inodes+0x166/0x1c0 Sep 07 11:55:32 debian9 kernel: generic_shutdown_super+0x71/0x120 Sep 07 11:55:32 debian9 kernel: kill_anon_super+0x14/0x30 Sep 07 11:55:32 debian9 kernel: btrfs_kill_super+0x12/0x20 [btrfs] Sep 07 11:55:32 debian9 kernel: deactivate_locked_super+0x2e/0xa0 Sep 07 11:55:32 debian9 kernel: cleanup_mnt+0x100/0x160 Sep 07 11:55:32 debian9 kernel: task_work_run+0x59/0xa0 Sep 07 11:55:32 debian9 kernel: exit_to_user_mode_prepare+0x1a6/0x1b0 Sep 07 11:55:32 debian9 kernel: syscall_exit_to_user_mode+0x16/0x40 Sep 07 11:55:32 debian9 kernel: do_syscall_64+0x48/0x90 Sep 07 11:55:32 debian9 kernel: entry_SYSCALL_64_after_hwframe+0x63/0xcd Sep 07 11:55:32 debian9 kernel: RIP: 0033:0x7fcde59a57a7 Sep 07 11:55:32 debian9 kernel: RSP: 002b:00007ffe914217c8 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6 Sep 07 11:55:32 debian9 kernel: RAX: 0000000000000000 RBX: 00007fcde5ae8264 RCX: 00007fcde59a57a7 Sep 07 11:55:32 debian9 kernel: RDX: 0000000000000000 RSI: 0000000000000000 RDI: 000055b57556cdd0 Sep 07 11:55:32 debian9 kernel: RBP: 000055b57556cba0 R08: 0000000000000000 R09: 00007ffe91420570 Sep 07 11:55:32 debian9 kernel: R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 Sep 07 11:55:32 debian9 kernel: R13: 000055b57556cdd0 R14: 000055b57556ccb8 R15: 0000000000000000 Sep 07 11:55:32 debian9 kernel: </TASK> What happens is the following: 1) The cleaner kthread tries to start a transaction to delete an unused block group, but the metadata reservation can not be satisfied right away, so a reservation ticket is created and it starts the async metadata reclaim task (fs_info->async_reclaim_work); 2) Writeback for all the filler inodes with an i_size of 2K starts (generic/562 creates a lot of 2K files with the goal of filling metadata space). We try to create an inline extent for them, but we fail when trying to insert the inline extent with -ENOSPC (at cow_file_range_inline()) - since this is not critical, we fallback to non-inline mode (back to cow_file_range()), reserve extents ---truncated---

In the Linux kernel, the following vulnerability has been resolved: drm/gma500: Fix WARN_ON(lock->magic != lock) error psb_gem_unpin() calls dma_resv_lock() but the underlying ww_mutex gets destroyed by drm_gem_object_release() move the drm_gem_object_release() call in psb_gem_free_object() to after the unpin to fix the below warning: [ 79.693962] ------------[ cut here ]------------ [ 79.693992] DEBUG_LOCKS_WARN_ON(lock->magic != lock) [ 79.694015] WARNING: CPU: 0 PID: 240 at kernel/locking/mutex.c:582 __ww_mutex_lock.constprop.0+0x569/0xfb0 [ 79.694052] Modules linked in: rfcomm snd_seq_dummy snd_hrtimer qrtr bnep ath9k ath9k_common ath9k_hw snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_codec_hdmi snd_hda_intel ath3k snd_intel_dspcfg mac80211 snd_intel_sdw_acpi btusb snd_hda_codec btrtl btbcm btintel btmtk bluetooth at24 snd_hda_core snd_hwdep uvcvideo snd_seq libarc4 videobuf2_vmalloc ath videobuf2_memops videobuf2_v4l2 videobuf2_common snd_seq_device videodev acer_wmi intel_powerclamp coretemp mc snd_pcm joydev sparse_keymap ecdh_generic pcspkr wmi_bmof cfg80211 i2c_i801 i2c_smbus snd_timer snd r8169 rfkill lpc_ich soundcore acpi_cpufreq zram rtsx_pci_sdmmc mmc_core serio_raw rtsx_pci gma500_gfx(E) video wmi ip6_tables ip_tables i2c_dev fuse [ 79.694436] CPU: 0 PID: 240 Comm: plymouthd Tainted: G W E 6.0.0-rc3+ #490 [ 79.694457] Hardware name: Packard Bell dot s/SJE01_CT, BIOS V1.10 07/23/2013 [ 79.694469] RIP: 0010:__ww_mutex_lock.constprop.0+0x569/0xfb0 [ 79.694496] Code: ff 85 c0 0f 84 15 fb ff ff 8b 05 ca 3c 11 01 85 c0 0f 85 07 fb ff ff 48 c7 c6 30 cb 84 aa 48 c7 c7 a3 e1 82 aa e8 ac 29 f8 ff <0f> 0b e9 ed fa ff ff e8 5b 83 8a ff 85 c0 74 10 44 8b 0d 98 3c 11 [ 79.694513] RSP: 0018:ffffad1dc048bbe0 EFLAGS: 00010282 [ 79.694623] RAX: 0000000000000028 RBX: 0000000000000000 RCX: 0000000000000000 [ 79.694636] RDX: 0000000000000001 RSI: ffffffffaa8b0ffc RDI: 00000000ffffffff [ 79.694650] RBP: ffffad1dc048bc80 R08: 0000000000000000 R09: ffffad1dc048ba90 [ 79.694662] R10: 0000000000000003 R11: ffffffffaad62fe8 R12: ffff9ff302103138 [ 79.694675] R13: ffff9ff306ec8000 R14: ffff9ff307779078 R15: ffff9ff3014c0270 [ 79.694690] FS: 00007ff1cccf1740(0000) GS:ffff9ff3bc200000(0000) knlGS:0000000000000000 [ 79.694705] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 79.694719] CR2: 0000559ecbcb4420 CR3: 0000000013210000 CR4: 00000000000006f0 [ 79.694734] Call Trace: [ 79.694749] <TASK> [ 79.694761] ? __schedule+0x47f/0x1670 [ 79.694796] ? psb_gem_unpin+0x27/0x1a0 [gma500_gfx] [ 79.694830] ? lock_is_held_type+0xe3/0x140 [ 79.694864] ? ww_mutex_lock+0x38/0xa0 [ 79.694885] ? __cond_resched+0x1c/0x30 [ 79.694902] ww_mutex_lock+0x38/0xa0 [ 79.694925] psb_gem_unpin+0x27/0x1a0 [gma500_gfx] [ 79.694964] psb_gem_unpin+0x199/0x1a0 [gma500_gfx] [ 79.694996] drm_gem_object_release_handle+0x50/0x60 [ 79.695020] ? drm_gem_object_handle_put_unlocked+0xf0/0xf0 [ 79.695042] idr_for_each+0x4b/0xb0 [ 79.695066] ? _raw_spin_unlock_irqrestore+0x30/0x60 [ 79.695095] drm_gem_release+0x1c/0x30 [ 79.695118] drm_file_free.part.0+0x1ea/0x260 [ 79.695150] drm_release+0x6a/0x120 [ 79.695175] __fput+0x9f/0x260 [ 79.695203] task_work_run+0x59/0xa0 [ 79.695227] do_exit+0x387/0xbe0 [ 79.695250] ? seqcount_lockdep_reader_access.constprop.0+0x82/0x90 [ 79.695275] ? lockdep_hardirqs_on+0x7d/0x100 [ 79.695304] do_group_exit+0x33/0xb0 [ 79.695331] __x64_sys_exit_group+0x14/0x20 [ 79.695353] do_syscall_64+0x58/0x80 [ 79.695376] ? up_read+0x17/0x20 [ 79.695401] ? lock_is_held_type+0xe3/0x140 [ 79.695429] ? asm_exc_page_fault+0x22/0x30 [ 79.695450] ? lockdep_hardirqs_on+0x7d/0x100 [ 79.695473] entry_SYSCALL_64_after_hwframe+0x63/0xcd [ 79.695493] RIP: 0033:0x7ff1ccefe3f1 [ 79.695516] Code: Unable to access opcode bytes at RIP 0x7ff1ccefe3c7. [ 79.695607] RSP: 002b:00007ffed4413378 EFLAGS: ---truncated---

In the Linux kernel, the following vulnerability has been resolved: ath11k: mhi: use mhi_sync_power_up() If amss.bin was missing ath11k would crash during 'rmmod ath11k_pci'. The reason for that was that we were using mhi_async_power_up() which does not check any errors. But mhi_sync_power_up() on the other hand does check for errors so let's use that to fix the crash. I was not able to find a reason why an async version was used. ath11k_mhi_start() (which enables state ATH11K_MHI_POWER_ON) is called from ath11k_hif_power_up(), which can sleep. So sync version should be safe to use here. [ 145.569731] general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN PTI [ 145.569789] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] [ 145.569843] CPU: 2 PID: 1628 Comm: rmmod Kdump: loaded Tainted: G W 5.16.0-wt-ath+ #567 [ 145.569898] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0067.2021.0528.1339 05/28/2021 [ 145.569956] RIP: 0010:ath11k_hal_srng_access_begin+0xb5/0x2b0 [ath11k] [ 145.570028] Code: df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 ec 01 00 00 48 8b ab a8 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 ea 48 c1 ea 03 <0f> b6 14 02 48 89 e8 83 e0 07 83 c0 03 45 85 ed 75 48 38 d0 7c 08 [ 145.570089] RSP: 0018:ffffc900025d7ac0 EFLAGS: 00010246 [ 145.570144] RAX: dffffc0000000000 RBX: ffff88814fca2dd8 RCX: 1ffffffff50cb455 [ 145.570196] RDX: 0000000000000000 RSI: ffff88814fca2dd8 RDI: ffff88814fca2e80 [ 145.570252] RBP: 0000000000000000 R08: 0000000000000000 R09: ffffffffa8659497 [ 145.570329] R10: fffffbfff50cb292 R11: 0000000000000001 R12: ffff88814fca0000 [ 145.570410] R13: 0000000000000000 R14: ffff88814fca2798 R15: ffff88814fca2dd8 [ 145.570465] FS: 00007fa399988540(0000) GS:ffff888233e00000(0000) knlGS:0000000000000000 [ 145.570519] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 145.570571] CR2: 00007fa399b51421 CR3: 0000000137898002 CR4: 00000000003706e0 [ 145.570623] Call Trace: [ 145.570675] <TASK> [ 145.570727] ? ath11k_ce_tx_process_cb+0x34b/0x860 [ath11k] [ 145.570797] ath11k_ce_tx_process_cb+0x356/0x860 [ath11k] [ 145.570864] ? tasklet_init+0x150/0x150 [ 145.570919] ? ath11k_ce_alloc_pipes+0x280/0x280 [ath11k] [ 145.570986] ? tasklet_clear_sched+0x42/0xe0 [ 145.571042] ? tasklet_kill+0xe9/0x1b0 [ 145.571095] ? tasklet_clear_sched+0xe0/0xe0 [ 145.571148] ? irq_has_action+0x120/0x120 [ 145.571202] ath11k_ce_cleanup_pipes+0x45a/0x580 [ath11k] [ 145.571270] ? ath11k_pci_stop+0x10e/0x170 [ath11k_pci] [ 145.571345] ath11k_core_stop+0x8a/0xc0 [ath11k] [ 145.571434] ath11k_core_deinit+0x9e/0x150 [ath11k] [ 145.571499] ath11k_pci_remove+0xd2/0x260 [ath11k_pci] [ 145.571553] pci_device_remove+0x9a/0x1c0 [ 145.571605] __device_release_driver+0x332/0x660 [ 145.571659] driver_detach+0x1e7/0x2c0 [ 145.571712] bus_remove_driver+0xe2/0x2d0 [ 145.571772] pci_unregister_driver+0x21/0x250 [ 145.571826] __do_sys_delete_module+0x30a/0x4b0 [ 145.571879] ? free_module+0xac0/0xac0 [ 145.571933] ? lockdep_hardirqs_on_prepare.part.0+0x18c/0x370 [ 145.571986] ? syscall_enter_from_user_mode+0x1d/0x50 [ 145.572039] ? lockdep_hardirqs_on+0x79/0x100 [ 145.572097] do_syscall_64+0x3b/0x90 [ 145.572153] entry_SYSCALL_64_after_hwframe+0x44/0xae Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

In nf_tables_updtable, if nf_tables_table_enable returns an error, nft_trans_destroy is called to free the transaction object. nft_trans_destroy() calls list_del(), but the transaction was never placed on a list -- the list head is all zeroes, this results in a NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: comedi: vmk80xx: fix incomplete endpoint checking While vmk80xx does have endpoint checking implemented, some things can fall through the cracks. Depending on the hardware model, URBs can have either bulk or interrupt type, and current version of vmk80xx_find_usb_endpoints() function does not take that fully into account. While this warning does not seem to be too harmful, at the very least it will crash systems with 'panic_on_warn' set on them. Fix the issue found by Syzkaller [1] by somewhat simplifying the endpoint checking process with usb_find_common_endpoints() and ensuring that only expected endpoint types are present. This patch has not been tested on real hardware. [1] Syzkaller report: usb 1-1: BOGUS urb xfer, pipe 1 != type 3 WARNING: CPU: 0 PID: 781 at drivers/usb/core/urb.c:504 usb_submit_urb+0xc4e/0x18c0 drivers/usb/core/urb.c:503 ... Call Trace: <TASK> usb_start_wait_urb+0x113/0x520 drivers/usb/core/message.c:59 vmk80xx_reset_device drivers/comedi/drivers/vmk80xx.c:227 [inline] vmk80xx_auto_attach+0xa1c/0x1a40 drivers/comedi/drivers/vmk80xx.c:818 comedi_auto_config+0x238/0x380 drivers/comedi/drivers.c:1067 usb_probe_interface+0x5cd/0xb00 drivers/usb/core/driver.c:399 ... Similar issue also found by Syzkaller:

In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress basechain Remove netdevice from inet/ingress basechain in case NETDEV_UNREGISTER event is reported, otherwise a stale reference to netdevice remains in the hook list.

In the Linux kernel, the following vulnerability has been resolved: nfs: fix panic when nfs4_ff_layout_prepare_ds() fails We've been seeing the following panic in production BUG: kernel NULL pointer dereference, address: 0000000000000065 PGD 2f485f067 P4D 2f485f067 PUD 2cc5d8067 PMD 0 RIP: 0010:ff_layout_cancel_io+0x3a/0x90 [nfs_layout_flexfiles] Call Trace: <TASK> ? __die+0x78/0xc0 ? page_fault_oops+0x286/0x380 ? __rpc_execute+0x2c3/0x470 [sunrpc] ? rpc_new_task+0x42/0x1c0 [sunrpc] ? exc_page_fault+0x5d/0x110 ? asm_exc_page_fault+0x22/0x30 ? ff_layout_free_layoutreturn+0x110/0x110 [nfs_layout_flexfiles] ? ff_layout_cancel_io+0x3a/0x90 [nfs_layout_flexfiles] ? ff_layout_cancel_io+0x6f/0x90 [nfs_layout_flexfiles] pnfs_mark_matching_lsegs_return+0x1b0/0x360 [nfsv4] pnfs_error_mark_layout_for_return+0x9e/0x110 [nfsv4] ? ff_layout_send_layouterror+0x50/0x160 [nfs_layout_flexfiles] nfs4_ff_layout_prepare_ds+0x11f/0x290 [nfs_layout_flexfiles] ff_layout_pg_init_write+0xf0/0x1f0 [nfs_layout_flexfiles] __nfs_pageio_add_request+0x154/0x6c0 [nfs] nfs_pageio_add_request+0x26b/0x380 [nfs] nfs_do_writepage+0x111/0x1e0 [nfs] nfs_writepages_callback+0xf/0x30 [nfs] write_cache_pages+0x17f/0x380 ? nfs_pageio_init_write+0x50/0x50 [nfs] ? nfs_writepages+0x6d/0x210 [nfs] ? nfs_writepages+0x6d/0x210 [nfs] nfs_writepages+0x125/0x210 [nfs] do_writepages+0x67/0x220 ? generic_perform_write+0x14b/0x210 filemap_fdatawrite_wbc+0x5b/0x80 file_write_and_wait_range+0x6d/0xc0 nfs_file_fsync+0x81/0x170 [nfs] ? nfs_file_mmap+0x60/0x60 [nfs] __x64_sys_fsync+0x53/0x90 do_syscall_64+0x3d/0x90 entry_SYSCALL_64_after_hwframe+0x46/0xb0 Inspecting the core with drgn I was able to pull this >>> prog.crashed_thread().stack_trace()[0] #0 at 0xffffffffa079657a (ff_layout_cancel_io+0x3a/0x84) in ff_layout_cancel_io at fs/nfs/flexfilelayout/flexfilelayout.c:2021:27 >>> prog.crashed_thread().stack_trace()[0]['idx'] (u32)1 >>> prog.crashed_thread().stack_trace()[0]['flseg'].mirror_array[1].mirror_ds (struct nfs4_ff_layout_ds *)0xffffffffffffffed This is clear from the stack trace, we call nfs4_ff_layout_prepare_ds() which could error out initializing the mirror_ds, and then we go to clean it all up and our check is only for if (!mirror->mirror_ds). This is inconsistent with the rest of the users of mirror_ds, which have if (IS_ERR_OR_NULL(mirror_ds)) to keep from tripping over this exact scenario. Fix this up in ff_layout_cancel_io() to make sure we don't panic when we get an error. I also spot checked all the other instances of checking mirror_ds and we appear to be doing the correct checks everywhere, only unconditionally dereferencing mirror_ds when we know it would be valid.

In the Linux kernel, the following vulnerability has been resolved: lib/Kconfig.debug: TEST_IOV_ITER depends on MMU Trying to run the iov_iter unit test on a nommu system such as the qemu kc705-nommu emulation results in a crash. KTAP version 1 # Subtest: iov_iter # module: kunit_iov_iter 1..9 BUG: failure at mm/nommu.c:318/vmap()! Kernel panic - not syncing: BUG! The test calls vmap() directly, but vmap() is not supported on nommu systems, causing the crash. TEST_IOV_ITER therefore needs to depend on MMU.

A use-after-free flaw was found in io_uring/filetable.c in io_install_fixed_file in the io_uring subcomponent in the Linux Kernel during call cleanup. This flaw may lead to a denial of service.

In the Linux kernel, the following vulnerability has been resolved: btrfs: handle chunk tree lookup error in btrfs_relocate_sys_chunks() The unhandled case in btrfs_relocate_sys_chunks() loop is a corruption, as it could be caused only by two impossible conditions: - at first the search key is set up to look for a chunk tree item, with offset -1, this is an inexact search and the key->offset will contain the correct offset upon a successful search, a valid chunk tree item cannot have an offset -1 - after first successful search, the found_key corresponds to a chunk item, the offset is decremented by 1 before the next loop, it's impossible to find a chunk item there due to alignment and size constraints

In the Linux kernel, the following vulnerability has been resolved: i40e: Fix queues reservation for XDP When XDP was configured on a system with large number of CPUs and X722 NIC there was a call trace with NULL pointer dereference. i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12 i40e 0000:87:00.0: setup of MAIN VSI failed BUG: kernel NULL pointer dereference, address: 0000000000000000 RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e] Call Trace: ? i40e_reconfig_rss_queues+0x130/0x130 [i40e] dev_xdp_install+0x61/0xe0 dev_xdp_attach+0x18a/0x4c0 dev_change_xdp_fd+0x1e6/0x220 do_setlink+0x616/0x1030 ? ahci_port_stop+0x80/0x80 ? ata_qc_issue+0x107/0x1e0 ? lock_timer_base+0x61/0x80 ? __mod_timer+0x202/0x380 rtnl_setlink+0xe5/0x170 ? bpf_lsm_binder_transaction+0x10/0x10 ? security_capable+0x36/0x50 rtnetlink_rcv_msg+0x121/0x350 ? rtnl_calcit.isra.0+0x100/0x100 netlink_rcv_skb+0x50/0xf0 netlink_unicast+0x1d3/0x2a0 netlink_sendmsg+0x22a/0x440 sock_sendmsg+0x5e/0x60 __sys_sendto+0xf0/0x160 ? __sys_getsockname+0x7e/0xc0 ? _copy_from_user+0x3c/0x80 ? __sys_setsockopt+0xc8/0x1a0 __x64_sys_sendto+0x20/0x30 do_syscall_64+0x33/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f83fa7a39e0 This was caused by PF queue pile fragmentation due to flow director VSI queue being placed right after main VSI. Because of this main VSI was not able to resize its queue allocation for XDP resulting in no queues allocated for main VSI when XDP was turned on. Fix this by always allocating last queue in PF queue pile for a flow director VSI.

In the Linux kernel, the following vulnerability has been resolved: bpf, skmsg: Fix NULL pointer dereference in sk_psock_skb_ingress_enqueue Fix NULL pointer data-races in sk_psock_skb_ingress_enqueue() which syzbot reported [1]. [1] BUG: KCSAN: data-race in sk_psock_drop / sk_psock_skb_ingress_enqueue write to 0xffff88814b3278b8 of 8 bytes by task 10724 on cpu 1: sk_psock_stop_verdict net/core/skmsg.c:1257 [inline] sk_psock_drop+0x13e/0x1f0 net/core/skmsg.c:843 sk_psock_put include/linux/skmsg.h:459 [inline] sock_map_close+0x1a7/0x260 net/core/sock_map.c:1648 unix_release+0x4b/0x80 net/unix/af_unix.c:1048 __sock_release net/socket.c:659 [inline] sock_close+0x68/0x150 net/socket.c:1421 __fput+0x2c1/0x660 fs/file_table.c:422 __fput_sync+0x44/0x60 fs/file_table.c:507 __do_sys_close fs/open.c:1556 [inline] __se_sys_close+0x101/0x1b0 fs/open.c:1541 __x64_sys_close+0x1f/0x30 fs/open.c:1541 do_syscall_64+0xd3/0x1d0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 read to 0xffff88814b3278b8 of 8 bytes by task 10713 on cpu 0: sk_psock_data_ready include/linux/skmsg.h:464 [inline] sk_psock_skb_ingress_enqueue+0x32d/0x390 net/core/skmsg.c:555 sk_psock_skb_ingress_self+0x185/0x1e0 net/core/skmsg.c:606 sk_psock_verdict_apply net/core/skmsg.c:1008 [inline] sk_psock_verdict_recv+0x3e4/0x4a0 net/core/skmsg.c:1202 unix_read_skb net/unix/af_unix.c:2546 [inline] unix_stream_read_skb+0x9e/0xf0 net/unix/af_unix.c:2682 sk_psock_verdict_data_ready+0x77/0x220 net/core/skmsg.c:1223 unix_stream_sendmsg+0x527/0x860 net/unix/af_unix.c:2339 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg+0x140/0x180 net/socket.c:745 ____sys_sendmsg+0x312/0x410 net/socket.c:2584 ___sys_sendmsg net/socket.c:2638 [inline] __sys_sendmsg+0x1e9/0x280 net/socket.c:2667 __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x46/0x50 net/socket.c:2674 do_syscall_64+0xd3/0x1d0 entry_SYSCALL_64_after_hwframe+0x6d/0x75 value changed: 0xffffffff83d7feb0 -> 0x0000000000000000 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 10713 Comm: syz-executor.4 Tainted: G W 6.8.0-syzkaller-08951-gfe46a7dd189e #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024 Prior to this, commit 4cd12c6065df ("bpf, sockmap: Fix NULL pointer dereference in sk_psock_verdict_data_ready()") fixed one NULL pointer similarly due to no protection of saved_data_ready. Here is another different caller causing the same issue because of the same reason. So we should protect it with sk_callback_lock read lock because the writer side in the sk_psock_drop() uses "write_lock_bh(&sk->sk_callback_lock);". To avoid errors that could happen in future, I move those two pairs of lock into the sk_psock_data_ready(), which is suggested by John Fastabend.

In the Linux kernel, the following vulnerability has been resolved: s390/bpf: Fix bpf_plt pointer arithmetic Kui-Feng Lee reported a crash on s390x triggered by the dummy_st_ops/dummy_init_ptr_arg test [1]: [<0000000000000002>] 0x2 [<00000000009d5cde>] bpf_struct_ops_test_run+0x156/0x250 [<000000000033145a>] __sys_bpf+0xa1a/0xd00 [<00000000003319dc>] __s390x_sys_bpf+0x44/0x50 [<0000000000c4382c>] __do_syscall+0x244/0x300 [<0000000000c59a40>] system_call+0x70/0x98 This is caused by GCC moving memcpy() after assignments in bpf_jit_plt(), resulting in NULL pointers being written instead of the return and the target addresses. Looking at the GCC internals, the reordering is allowed because the alias analysis thinks that the memcpy() destination and the assignments' left-hand-sides are based on different objects: new_plt and bpf_plt_ret/bpf_plt_target respectively, and therefore they cannot alias. This is in turn due to a violation of the C standard: When two pointers are subtracted, both shall point to elements of the same array object, or one past the last element of the array object ... From the C's perspective, bpf_plt_ret and bpf_plt are distinct objects and cannot be subtracted. In the practical terms, doing so confuses the GCC's alias analysis. The code was written this way in order to let the C side know a few offsets defined in the assembly. While nice, this is by no means necessary. Fix the noncompliance by hardcoding these offsets. [1] https://lore.kernel.org/bpf/c9923c1d-971d-4022-8dc8-1364e929d34c@gmail.com/

In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: uefisecapp: Fix memory related IO errors and crashes It turns out that while the QSEECOM APP_SEND command has specific fields for request and response buffers, uefisecapp expects them both to be in a single memory region. Failure to adhere to this has (so far) resulted in either no response being written to the response buffer (causing an EIO to be emitted down the line), the SCM call to fail with EINVAL (i.e., directly from TZ/firmware), or the device to be hard-reset. While this issue can be triggered deterministically, in the current form it seems to happen rather sporadically (which is why it has gone unnoticed during earlier testing). This is likely due to the two kzalloc() calls (for request and response) being directly after each other. Which means that those likely return consecutive regions most of the time, especially when not much else is going on in the system. Fix this by allocating a single memory region for both request and response buffers, properly aligning both structs inside it. This unfortunately also means that the qcom_scm_qseecom_app_send() interface needs to be restructured, as it should no longer map the DMA regions separately. Therefore, move the responsibility of DMA allocation (or mapping) to the caller.

In the Linux kernel, the following vulnerability has been resolved: IB/hfi1: Fix sdma.h tx->num_descs off-by-one error Unfortunately the commit `fd8958efe877` introduced another error causing the `descs` array to overflow. This reults in further crashes easily reproducible by `sendmsg` system call. [ 1080.836473] general protection fault, probably for non-canonical address 0x400300015528b00a: 0000 [#1] PREEMPT SMP PTI [ 1080.869326] RIP: 0010:hfi1_ipoib_build_ib_tx_headers.constprop.0+0xe1/0x2b0 [hfi1] -- [ 1080.974535] Call Trace: [ 1080.976990] <TASK> [ 1081.021929] hfi1_ipoib_send_dma_common+0x7a/0x2e0 [hfi1] [ 1081.027364] hfi1_ipoib_send_dma_list+0x62/0x270 [hfi1] [ 1081.032633] hfi1_ipoib_send+0x112/0x300 [hfi1] [ 1081.042001] ipoib_start_xmit+0x2a9/0x2d0 [ib_ipoib] [ 1081.046978] dev_hard_start_xmit+0xc4/0x210 -- [ 1081.148347] __sys_sendmsg+0x59/0xa0 crash> ipoib_txreq 0xffff9cfeba229f00 struct ipoib_txreq { txreq = { list = { next = 0xffff9cfeba229f00, prev = 0xffff9cfeba229f00 }, descp = 0xffff9cfeba229f40, coalesce_buf = 0x0, wait = 0xffff9cfea4e69a48, complete = 0xffffffffc0fe0760 <hfi1_ipoib_sdma_complete>, packet_len = 0x46d, tlen = 0x0, num_desc = 0x0, desc_limit = 0x6, next_descq_idx = 0x45c, coalesce_idx = 0x0, flags = 0x0, descs = {{ qw = {0x8024000120dffb00, 0x4} # SDMA_DESC0_FIRST_DESC_FLAG (bit 63) }, { qw = { 0x3800014231b108, 0x4} }, { qw = { 0x310000e4ee0fcf0, 0x8} }, { qw = { 0x3000012e9f8000, 0x8} }, { qw = { 0x59000dfb9d0000, 0x8} }, { qw = { 0x78000e02e40000, 0x8} }} }, sdma_hdr = 0x400300015528b000, <<< invalid pointer in the tx request structure sdma_status = 0x0, SDMA_DESC0_LAST_DESC_FLAG (bit 62) complete = 0x0, priv = 0x0, txq = 0xffff9cfea4e69880, skb = 0xffff9d099809f400 } If an SDMA send consists of exactly 6 descriptors and requires dword padding (in the 7th descriptor), the sdma_txreq descriptor array is not properly expanded and the packet will overflow into the container structure. This results in a panic when the send completion runs. The exact panic varies depending on what elements of the container structure get corrupted. The fix is to use the correct expression in _pad_sdma_tx_descs() to test the need to expand the descriptor array. With this patch the crashes are no longer reproducible and the machine is stable.

In the Linux kernel, the following vulnerability has been resolved: NFSD: Fix nfsd4_encode_fattr4() crasher Ensure that args.acl is initialized early. It is used in an unconditional call to kfree() on the way out of nfsd4_encode_fattr4().

In the Linux kernel, the following vulnerability has been resolved: net/sched: taprio: extend minimum interval restriction to entire cycle too It is possible for syzbot to side-step the restriction imposed by the blamed commit in the Fixes: tag, because the taprio UAPI permits a cycle-time different from (and potentially shorter than) the sum of entry intervals. We need one more restriction, which is that the cycle time itself must be larger than N * ETH_ZLEN bit times, where N is the number of schedule entries. This restriction needs to apply regardless of whether the cycle time came from the user or was the implicit, auto-calculated value, so we move the existing "cycle == 0" check outside the "if "(!new->cycle_time)" branch. This way covers both conditions and scenarios. Add a selftest which illustrates the issue triggered by syzbot.

In the Linux kernel, the following vulnerability has been resolved: riscv: Fix sleeping in invalid context in die() die() can be called in exception handler, and therefore cannot sleep. However, die() takes spinlock_t which can sleep with PREEMPT_RT enabled. That causes the following warning: BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 285, name: mutex preempt_count: 110001, expected: 0 RCU nest depth: 0, expected: 0 CPU: 0 UID: 0 PID: 285 Comm: mutex Not tainted 6.12.0-rc7-00022-ge19049cf7d56-dirty #234 Hardware name: riscv-virtio,qemu (DT) Call Trace: dump_backtrace+0x1c/0x24 show_stack+0x2c/0x38 dump_stack_lvl+0x5a/0x72 dump_stack+0x14/0x1c __might_resched+0x130/0x13a rt_spin_lock+0x2a/0x5c die+0x24/0x112 do_trap_insn_illegal+0xa0/0xea _new_vmalloc_restore_context_a0+0xcc/0xd8 Oops - illegal instruction [#1] Switch to use raw_spinlock_t, which does not sleep even with PREEMPT_RT enabled.

In the Linux kernel, the following vulnerability has been resolved: HID: i2c-hid: remove I2C_HID_READ_PENDING flag to prevent lock-up The flag I2C_HID_READ_PENDING is used to serialize I2C operations. However, this is not necessary, because I2C core already has its own locking for that. More importantly, this flag can cause a lock-up: if the flag is set in i2c_hid_xfer() and an interrupt happens, the interrupt handler (i2c_hid_irq) will check this flag and return immediately without doing anything, then the interrupt handler will be invoked again in an infinite loop. Since interrupt handler is an RT task, it takes over the CPU and the flag-clearing task never gets scheduled, thus we have a lock-up. Delete this unnecessary flag.

A use-after-free flaw was found in reconn_set_ipaddr_from_hostname in fs/cifs/connect.c in the Linux kernel. The issue occurs when it forgets to set the free pointer server->hostname to NULL, leading to an invalid pointer request.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: Avoid WARN_ON timing related checks The soft/batadv interface for a queued OGM can be changed during the time the OGM was queued for transmission and when the OGM is actually transmitted by the worker. But WARN_ON must be used to denote kernel bugs and not to print simple warnings. A warning can simply be printed using pr_warn.

In the Linux kernel, the following vulnerability has been resolved: clk: Fix clk_core_get NULL dereference It is possible for clk_core_get to dereference a NULL in the following sequence: clk_core_get() of_clk_get_hw_from_clkspec() __of_clk_get_hw_from_provider() __clk_get_hw() __clk_get_hw() can return NULL which is dereferenced by clk_core_get() at hw->core. Prior to commit dde4eff47c82 ("clk: Look for parents with clkdev based clk_lookups") the check IS_ERR_OR_NULL() was performed which would have caught the NULL. Reading the description of this function it talks about returning NULL but that cannot be so at the moment. Update the function to check for hw before dereferencing it and return NULL if hw is NULL.

In the Linux kernel, the following vulnerability has been resolved: usb: dwc3: core: Do core softreset when switch mode According to the programming guide, to switch mode for DRD controller, the driver needs to do the following. To switch from device to host: 1. Reset controller with GCTL.CoreSoftReset 2. Set GCTL.PrtCapDir(host mode) 3. Reset the host with USBCMD.HCRESET 4. Then follow up with the initializing host registers sequence To switch from host to device: 1. Reset controller with GCTL.CoreSoftReset 2. Set GCTL.PrtCapDir(device mode) 3. Reset the device with DCTL.CSftRst 4. Then follow up with the initializing registers sequence Currently we're missing step 1) to do GCTL.CoreSoftReset and step 3) of switching from host to device. John Stult reported a lockup issue seen with HiKey960 platform without these steps[1]. Similar issue is observed with Ferry's testing platform[2]. So, apply the required steps along with some fixes to Yu Chen's and John Stultz's version. The main fixes to their versions are the missing wait for clocks synchronization before clearing GCTL.CoreSoftReset and only apply DCTL.CSftRst when switching from host to device. [1] https://lore.kernel.org/linux-usb/20210108015115.27920-1-john.stultz@linaro.org/ [2] https://lore.kernel.org/linux-usb/0ba7a6ba-e6a7-9cd4-0695-64fc927e01f1@gmail.com/

In the Linux kernel, the following vulnerability has been resolved: ipv6: prevent NULL dereference in ip6_output() According to syzbot, there is a chance that ip6_dst_idev() returns NULL in ip6_output(). Most places in IPv6 stack deal with a NULL idev just fine, but not here. syzbot reported: general protection fault, probably for non-canonical address 0xdffffc00000000bc: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x00000000000005e0-0x00000000000005e7] CPU: 0 PID: 9775 Comm: syz-executor.4 Not tainted 6.9.0-rc5-syzkaller-00157-g6a30653b604a #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 RIP: 0010:ip6_output+0x231/0x3f0 net/ipv6/ip6_output.c:237 Code: 3c 1e 00 49 89 df 74 08 4c 89 ef e8 19 58 db f7 48 8b 44 24 20 49 89 45 00 49 89 c5 48 8d 9d e0 05 00 00 48 89 d8 48 c1 e8 03 <42> 0f b6 04 38 84 c0 4c 8b 74 24 28 0f 85 61 01 00 00 8b 1b 31 ff RSP: 0018:ffffc9000927f0d8 EFLAGS: 00010202 RAX: 00000000000000bc RBX: 00000000000005e0 RCX: 0000000000040000 RDX: ffffc900131f9000 RSI: 0000000000004f47 RDI: 0000000000004f48 RBP: 0000000000000000 R08: ffffffff8a1f0b9a R09: 1ffffffff1f51fad R10: dffffc0000000000 R11: fffffbfff1f51fae R12: ffff8880293ec8c0 R13: ffff88805d7fc000 R14: 1ffff1100527d91a R15: dffffc0000000000 FS: 00007f135c6856c0(0000) GS:ffff8880b9400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000080 CR3: 0000000064096000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> NF_HOOK include/linux/netfilter.h:314 [inline] ip6_xmit+0xefe/0x17f0 net/ipv6/ip6_output.c:358 sctp_v6_xmit+0x9f2/0x13f0 net/sctp/ipv6.c:248 sctp_packet_transmit+0x26ad/0x2ca0 net/sctp/output.c:653 sctp_packet_singleton+0x22c/0x320 net/sctp/outqueue.c:783 sctp_outq_flush_ctrl net/sctp/outqueue.c:914 [inline] sctp_outq_flush+0x6d5/0x3e20 net/sctp/outqueue.c:1212 sctp_side_effects net/sctp/sm_sideeffect.c:1198 [inline] sctp_do_sm+0x59cc/0x60c0 net/sctp/sm_sideeffect.c:1169 sctp_primitive_ASSOCIATE+0x95/0xc0 net/sctp/primitive.c:73 __sctp_connect+0x9cd/0xe30 net/sctp/socket.c:1234 sctp_connect net/sctp/socket.c:4819 [inline] sctp_inet_connect+0x149/0x1f0 net/sctp/socket.c:4834 __sys_connect_file net/socket.c:2048 [inline] __sys_connect+0x2df/0x310 net/socket.c:2065 __do_sys_connect net/socket.c:2075 [inline] __se_sys_connect net/socket.c:2072 [inline] __x64_sys_connect+0x7a/0x90 net/socket.c:2072 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: drm/i915: Fix crash in auto_retire The retire logic uses the 2 lower bits of the pointer to the retire function to store flags. However, the auto_retire function is not guaranteed to be aligned to a multiple of 4, which causes crashes as we jump to the wrong address, for example like this: 2021-04-24T18:03:53.804300Z WARNING kernel: [ 516.876901] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI 2021-04-24T18:03:53.804310Z WARNING kernel: [ 516.876906] CPU: 7 PID: 146 Comm: kworker/u16:6 Tainted: G U 5.4.105-13595-g3cd84167b2df #1 2021-04-24T18:03:53.804311Z WARNING kernel: [ 516.876907] Hardware name: Google Volteer2/Volteer2, BIOS Google_Volteer2.13672.76.0 02/22/2021 2021-04-24T18:03:53.804312Z WARNING kernel: [ 516.876911] Workqueue: events_unbound active_work 2021-04-24T18:03:53.804313Z WARNING kernel: [ 516.876914] RIP: 0010:auto_retire+0x1/0x20 2021-04-24T18:03:53.804314Z WARNING kernel: [ 516.876916] Code: e8 01 f2 ff ff eb 02 31 db 48 89 d8 5b 5d c3 0f 1f 44 00 00 55 48 89 e5 f0 ff 87 c8 00 00 00 0f 88 ab 47 4a 00 31 c0 5d c3 0f <1f> 44 00 00 55 48 89 e5 f0 ff 8f c8 00 00 00 0f 88 9a 47 4a 00 74 2021-04-24T18:03:53.804319Z WARNING kernel: [ 516.876918] RSP: 0018:ffff9b4d809fbe38 EFLAGS: 00010286 2021-04-24T18:03:53.804320Z WARNING kernel: [ 516.876919] RAX: 0000000000000007 RBX: ffff927915079600 RCX: 0000000000000007 2021-04-24T18:03:53.804320Z WARNING kernel: [ 516.876921] RDX: ffff9b4d809fbe40 RSI: 0000000000000286 RDI: ffff927915079600 2021-04-24T18:03:53.804321Z WARNING kernel: [ 516.876922] RBP: ffff9b4d809fbe68 R08: 8080808080808080 R09: fefefefefefefeff 2021-04-24T18:03:53.804321Z WARNING kernel: [ 516.876924] R10: 0000000000000010 R11: ffffffff92e44bd8 R12: ffff9279150796a0 2021-04-24T18:03:53.804322Z WARNING kernel: [ 516.876925] R13: ffff92791c368180 R14: ffff927915079640 R15: 000000001c867605 2021-04-24T18:03:53.804323Z WARNING kernel: [ 516.876926] FS: 0000000000000000(0000) GS:ffff92791ffc0000(0000) knlGS:0000000000000000 2021-04-24T18:03:53.804323Z WARNING kernel: [ 516.876928] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 2021-04-24T18:03:53.804324Z WARNING kernel: [ 516.876929] CR2: 0000239514955000 CR3: 00000007f82da001 CR4: 0000000000760ee0 2021-04-24T18:03:53.804325Z WARNING kernel: [ 516.876930] PKRU: 55555554 2021-04-24T18:03:53.804325Z WARNING kernel: [ 516.876931] Call Trace: 2021-04-24T18:03:53.804326Z WARNING kernel: [ 516.876935] __active_retire+0x77/0xcf 2021-04-24T18:03:53.804326Z WARNING kernel: [ 516.876939] process_one_work+0x1da/0x394 2021-04-24T18:03:53.804327Z WARNING kernel: [ 516.876941] worker_thread+0x216/0x375 2021-04-24T18:03:53.804327Z WARNING kernel: [ 516.876944] kthread+0x147/0x156 2021-04-24T18:03:53.804335Z WARNING kernel: [ 516.876946] ? pr_cont_work+0x58/0x58 2021-04-24T18:03:53.804335Z WARNING kernel: [ 516.876948] ? kthread_blkcg+0x2e/0x2e 2021-04-24T18:03:53.804336Z WARNING kernel: [ 516.876950] ret_from_fork+0x1f/0x40 2021-04-24T18:03:53.804336Z WARNING kernel: [ 516.876952] Modules linked in: cdc_mbim cdc_ncm cdc_wdm xt_cgroup rfcomm cmac algif_hash algif_skcipher af_alg xt_MASQUERADE uinput snd_soc_rt5682_sdw snd_soc_rt5682 snd_soc_max98373_sdw snd_soc_max98373 snd_soc_rl6231 regmap_sdw snd_soc_sof_sdw snd_soc_hdac_hdmi snd_soc_dmic snd_hda_codec_hdmi snd_sof_pci snd_sof_intel_hda_common intel_ipu6_psys snd_sof_xtensa_dsp soundwire_intel soundwire_generic_allocation soundwire_cadence snd_sof_intel_hda snd_sof snd_soc_hdac_hda snd_soc_acpi_intel_match snd_soc_acpi snd_hda_ext_core soundwire_bus snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hwdep snd_hda_core intel_ipu6_isys videobuf2_dma_contig videobuf2_v4l2 videobuf2_common videobuf2_memops mei_hdcp intel_ipu6 ov2740 ov8856 at24 sx9310 dw9768 v4l2_fwnode cros_ec_typec intel_pmc_mux roles acpi_als typec fuse iio_trig_sysfs cros_ec_light_prox cros_ec_lid_angle cros_ec_sensors cros ---truncated---

In the Linux kernel, the following vulnerability has been resolved: efi/unaccepted: touch soft lockup during memory accept Commit 50e782a86c98 ("efi/unaccepted: Fix soft lockups caused by parallel memory acceptance") has released the spinlock so other CPUs can do memory acceptance in parallel and not triggers softlockup on other CPUs. However the softlock up was intermittent shown up if the memory of the TD guest is large, and the timeout of softlockup is set to 1 second: RIP: 0010:_raw_spin_unlock_irqrestore Call Trace: ? __hrtimer_run_queues <IRQ> ? hrtimer_interrupt ? watchdog_timer_fn ? __sysvec_apic_timer_interrupt ? __pfx_watchdog_timer_fn ? sysvec_apic_timer_interrupt </IRQ> ? __hrtimer_run_queues <TASK> ? hrtimer_interrupt ? asm_sysvec_apic_timer_interrupt ? _raw_spin_unlock_irqrestore ? __sysvec_apic_timer_interrupt ? sysvec_apic_timer_interrupt accept_memory try_to_accept_memory do_huge_pmd_anonymous_page get_page_from_freelist __handle_mm_fault __alloc_pages __folio_alloc ? __tdx_hypercall handle_mm_fault vma_alloc_folio do_user_addr_fault do_huge_pmd_anonymous_page exc_page_fault ? __do_huge_pmd_anonymous_page asm_exc_page_fault __handle_mm_fault When the local irq is enabled at the end of accept_memory(), the softlockup detects that the watchdog on single CPU has not been fed for a while. That is to say, even other CPUs will not be blocked by spinlock, the current CPU might be stunk with local irq disabled for a while, which hurts not only nmi watchdog but also softlockup. Chao Gao pointed out that the memory accept could be time costly and there was similar report before. Thus to avoid any softlocup detection during this stage, give the softlockup a flag to skip the timeout check at the end of accept_memory(), by invoking touch_softlockup_watchdog().

In the Linux kernel, the following vulnerability has been resolved: ipv6: fix race condition between ipv6_get_ifaddr and ipv6_del_addr Although ipv6_get_ifaddr walks inet6_addr_lst under the RCU lock, it still means hlist_for_each_entry_rcu can return an item that got removed from the list. The memory itself of such item is not freed thanks to RCU but nothing guarantees the actual content of the memory is sane. In particular, the reference count can be zero. This can happen if ipv6_del_addr is called in parallel. ipv6_del_addr removes the entry from inet6_addr_lst (hlist_del_init_rcu(&ifp->addr_lst)) and drops all references (__in6_ifa_put(ifp) + in6_ifa_put(ifp)). With bad enough timing, this can happen: 1. In ipv6_get_ifaddr, hlist_for_each_entry_rcu returns an entry. 2. Then, the whole ipv6_del_addr is executed for the given entry. The reference count drops to zero and kfree_rcu is scheduled. 3. ipv6_get_ifaddr continues and tries to increments the reference count (in6_ifa_hold). 4. The rcu is unlocked and the entry is freed. 5. The freed entry is returned. Prevent increasing of the reference count in such case. The name in6_ifa_hold_safe is chosen to mimic the existing fib6_info_hold_safe. [ 41.506330] refcount_t: addition on 0; use-after-free. [ 41.506760] WARNING: CPU: 0 PID: 595 at lib/refcount.c:25 refcount_warn_saturate+0xa5/0x130 [ 41.507413] Modules linked in: veth bridge stp llc [ 41.507821] CPU: 0 PID: 595 Comm: python3 Not tainted 6.9.0-rc2.main-00208-g49563be82afa #14 [ 41.508479] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) [ 41.509163] RIP: 0010:refcount_warn_saturate+0xa5/0x130 [ 41.509586] Code: ad ff 90 0f 0b 90 90 c3 cc cc cc cc 80 3d c0 30 ad 01 00 75 a0 c6 05 b7 30 ad 01 01 90 48 c7 c7 38 cc 7a 8c e8 cc 18 ad ff 90 <0f> 0b 90 90 c3 cc cc cc cc 80 3d 98 30 ad 01 00 0f 85 75 ff ff ff [ 41.510956] RSP: 0018:ffffbda3c026baf0 EFLAGS: 00010282 [ 41.511368] RAX: 0000000000000000 RBX: ffff9e9c46914800 RCX: 0000000000000000 [ 41.511910] RDX: ffff9e9c7ec29c00 RSI: ffff9e9c7ec1c900 RDI: ffff9e9c7ec1c900 [ 41.512445] RBP: ffff9e9c43660c9c R08: 0000000000009ffb R09: 00000000ffffdfff [ 41.512998] R10: 00000000ffffdfff R11: ffffffff8ca58a40 R12: ffff9e9c4339a000 [ 41.513534] R13: 0000000000000001 R14: ffff9e9c438a0000 R15: ffffbda3c026bb48 [ 41.514086] FS: 00007fbc4cda1740(0000) GS:ffff9e9c7ec00000(0000) knlGS:0000000000000000 [ 41.514726] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 41.515176] CR2: 000056233b337d88 CR3: 000000000376e006 CR4: 0000000000370ef0 [ 41.515713] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 41.516252] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 41.516799] Call Trace: [ 41.517037] <TASK> [ 41.517249] ? __warn+0x7b/0x120 [ 41.517535] ? refcount_warn_saturate+0xa5/0x130 [ 41.517923] ? report_bug+0x164/0x190 [ 41.518240] ? handle_bug+0x3d/0x70 [ 41.518541] ? exc_invalid_op+0x17/0x70 [ 41.520972] ? asm_exc_invalid_op+0x1a/0x20 [ 41.521325] ? refcount_warn_saturate+0xa5/0x130 [ 41.521708] ipv6_get_ifaddr+0xda/0xe0 [ 41.522035] inet6_rtm_getaddr+0x342/0x3f0 [ 41.522376] ? __pfx_inet6_rtm_getaddr+0x10/0x10 [ 41.522758] rtnetlink_rcv_msg+0x334/0x3d0 [ 41.523102] ? netlink_unicast+0x30f/0x390 [ 41.523445] ? __pfx_rtnetlink_rcv_msg+0x10/0x10 [ 41.523832] netlink_rcv_skb+0x53/0x100 [ 41.524157] netlink_unicast+0x23b/0x390 [ 41.524484] netlink_sendmsg+0x1f2/0x440 [ 41.524826] __sys_sendto+0x1d8/0x1f0 [ 41.525145] __x64_sys_sendto+0x1f/0x30 [ 41.525467] do_syscall_64+0xa5/0x1b0 [ 41.525794] entry_SYSCALL_64_after_hwframe+0x72/0x7a [ 41.526213] RIP: 0033:0x7fbc4cfcea9a [ 41.526528] Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89 [ 41.527942] RSP: 002b:00007f ---truncated---

In the Linux kernel, the following vulnerability has been resolved: dm btree remove: assign new_root only when removal succeeds remove_raw() in dm_btree_remove() may fail due to IO read error (e.g. read the content of origin block fails during shadowing), and the value of shadow_spine::root is uninitialized, but the uninitialized value is still assign to new_root in the end of dm_btree_remove(). For dm-thin, the value of pmd->details_root or pmd->root will become an uninitialized value, so if trying to read details_info tree again out-of-bound memory may occur as showed below: general protection fault, probably for non-canonical address 0x3fdcb14c8d7520 CPU: 4 PID: 515 Comm: dmsetup Not tainted 5.13.0-rc6 Hardware name: QEMU Standard PC RIP: 0010:metadata_ll_load_ie+0x14/0x30 Call Trace: sm_metadata_count_is_more_than_one+0xb9/0xe0 dm_tm_shadow_block+0x52/0x1c0 shadow_step+0x59/0xf0 remove_raw+0xb2/0x170 dm_btree_remove+0xf4/0x1c0 dm_pool_delete_thin_device+0xc3/0x140 pool_message+0x218/0x2b0 target_message+0x251/0x290 ctl_ioctl+0x1c4/0x4d0 dm_ctl_ioctl+0xe/0x20 __x64_sys_ioctl+0x7b/0xb0 do_syscall_64+0x40/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae Fixing it by only assign new_root when removal succeeds

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix kernel crash when devlink reload during initialization The devlink reload process will access the hardware resources, but the register operation is done before the hardware is initialized. So, processing the devlink reload during initialization may lead to kernel crash. This patch fixes this by registering the devlink after hardware initialization.

In the Linux kernel, the following vulnerability has been resolved: ice: track AF_XDP ZC enabled queues in bitmap Commit c7a219048e45 ("ice: Remove xsk_buff_pool from VSI structure") silently introduced a regression and broke the Tx side of AF_XDP in copy mode. xsk_pool on ice_ring is set only based on the existence of the XDP prog on the VSI which in turn picks ice_clean_tx_irq_zc to be executed. That is not something that should happen for copy mode as it should use the regular data path ice_clean_tx_irq. This results in a following splat when xdpsock is run in txonly or l2fwd scenarios in copy mode: <snip> [ 106.050195] BUG: kernel NULL pointer dereference, address: 0000000000000030 [ 106.057269] #PF: supervisor read access in kernel mode [ 106.062493] #PF: error_code(0x0000) - not-present page [ 106.067709] PGD 0 P4D 0 [ 106.070293] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 106.074721] CPU: 61 PID: 0 Comm: swapper/61 Not tainted 5.12.0-rc2+ #45 [ 106.081436] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019 [ 106.092027] RIP: 0010:xp_raw_get_dma+0x36/0x50 [ 106.096551] Code: 74 14 48 b8 ff ff ff ff ff ff 00 00 48 21 f0 48 c1 ee 30 48 01 c6 48 8b 87 90 00 00 00 48 89 f2 81 e6 ff 0f 00 00 48 c1 ea 0c <48> 8b 04 d0 48 83 e0 fe 48 01 f0 c3 66 66 2e 0f 1f 84 00 00 00 00 [ 106.115588] RSP: 0018:ffffc9000d694e50 EFLAGS: 00010206 [ 106.120893] RAX: 0000000000000000 RBX: ffff88984b8c8a00 RCX: ffff889852581800 [ 106.128137] RDX: 0000000000000006 RSI: 0000000000000000 RDI: ffff88984cd8b800 [ 106.135383] RBP: ffff888123b50001 R08: ffff889896800000 R09: 0000000000000800 [ 106.142628] R10: 0000000000000000 R11: ffffffff826060c0 R12: 00000000000000ff [ 106.149872] R13: 0000000000000000 R14: 0000000000000040 R15: ffff888123b50018 [ 106.157117] FS: 0000000000000000(0000) GS:ffff8897e0f40000(0000) knlGS:0000000000000000 [ 106.165332] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 106.171163] CR2: 0000000000000030 CR3: 000000000560a004 CR4: 00000000007706e0 [ 106.178408] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 106.185653] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 106.192898] PKRU: 55555554 [ 106.195653] Call Trace: [ 106.198143] <IRQ> [ 106.200196] ice_clean_tx_irq_zc+0x183/0x2a0 [ice] [ 106.205087] ice_napi_poll+0x3e/0x590 [ice] [ 106.209356] __napi_poll+0x2a/0x160 [ 106.212911] net_rx_action+0xd6/0x200 [ 106.216634] __do_softirq+0xbf/0x29b [ 106.220274] irq_exit_rcu+0x88/0xc0 [ 106.223819] common_interrupt+0x7b/0xa0 [ 106.227719] </IRQ> [ 106.229857] asm_common_interrupt+0x1e/0x40 </snip> Fix this by introducing the bitmap of queues that are zero-copy enabled, where each bit, corresponding to a queue id that xsk pool is being configured on, will be set/cleared within ice_xsk_pool_{en,dis}able and checked within ice_xsk_pool(). The latter is a function used for deciding which napi poll routine is executed. Idea is being taken from our other drivers such as i40e and ixgbe.

In the Linux kernel, the following vulnerability has been resolved: bpf, sockmap: Fix potential memory leak on unlikely error case If skb_linearize is needed and fails we could leak a msg on the error handling. To fix ensure we kfree the msg block before returning error. Found during code review.

In the Linux kernel, the following vulnerability has been resolved: scsi: mpi3mr: Avoid memcpy field-spanning write WARNING When the "storcli2 show" command is executed for eHBA-9600, mpi3mr driver prints this WARNING message: memcpy: detected field-spanning write (size 128) of single field "bsg_reply_buf->reply_buf" at drivers/scsi/mpi3mr/mpi3mr_app.c:1658 (size 1) WARNING: CPU: 0 PID: 12760 at drivers/scsi/mpi3mr/mpi3mr_app.c:1658 mpi3mr_bsg_request+0x6b12/0x7f10 [mpi3mr] The cause of the WARN is 128 bytes memcpy to the 1 byte size array "__u8 replay_buf[1]" in the struct mpi3mr_bsg_in_reply_buf. The array is intended to be a flexible length array, so the WARN is a false positive. To suppress the WARN, remove the constant number '1' from the array declaration and clarify that it has flexible length. Also, adjust the memory allocation size to match the change.

In the Linux kernel, the following vulnerability has been resolved: RDMA: Verify port when creating flow rule Validate port value provided by the user and with that remove no longer needed validation by the driver. The missing check in the mlx5_ib driver could cause to the below oops. Call trace: _create_flow_rule+0x2d4/0xf28 [mlx5_ib] mlx5_ib_create_flow+0x2d0/0x5b0 [mlx5_ib] ib_uverbs_ex_create_flow+0x4cc/0x624 [ib_uverbs] ib_uverbs_handler_UVERBS_METHOD_INVOKE_WRITE+0xd4/0x150 [ib_uverbs] ib_uverbs_cmd_verbs.isra.7+0xb28/0xc50 [ib_uverbs] ib_uverbs_ioctl+0x158/0x1d0 [ib_uverbs] do_vfs_ioctl+0xd0/0xaf0 ksys_ioctl+0x84/0xb4 __arm64_sys_ioctl+0x28/0xc4 el0_svc_common.constprop.3+0xa4/0x254 el0_svc_handler+0x84/0xa0 el0_svc+0x10/0x26c Code: b9401260 f9615681 51000400 8b001c20 (f9403c1a)

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Fix MST Null Ptr for RV The change try to fix below error specific to RV platform: BUG: kernel NULL pointer dereference, address: 0000000000000008 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 4 PID: 917 Comm: sway Not tainted 6.3.9-arch1-1 #1 124dc55df4f5272ccb409f39ef4872fc2b3376a2 Hardware name: LENOVO 20NKS01Y00/20NKS01Y00, BIOS R12ET61W(1.31 ) 07/28/2022 RIP: 0010:drm_dp_atomic_find_time_slots+0x5e/0x260 [drm_display_helper] Code: 01 00 00 48 8b 85 60 05 00 00 48 63 80 88 00 00 00 3b 43 28 0f 8d 2e 01 00 00 48 8b 53 30 48 8d 04 80 48 8d 04 c2 48 8b 40 18 <48> 8> RSP: 0018:ffff960cc2df77d8 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffff8afb87e81280 RCX: 0000000000000224 RDX: ffff8afb9ee37c00 RSI: ffff8afb8da1a578 RDI: ffff8afb87e81280 RBP: ffff8afb83d67000 R08: 0000000000000001 R09: ffff8afb9652f850 R10: ffff960cc2df7908 R11: 0000000000000002 R12: 0000000000000000 R13: ffff8afb8d7688a0 R14: ffff8afb8da1a578 R15: 0000000000000224 FS: 00007f4dac35ce00(0000) GS:ffff8afe30b00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000008 CR3: 000000010ddc6000 CR4: 00000000003506e0 Call Trace: <TASK> ? __die+0x23/0x70 ? page_fault_oops+0x171/0x4e0 ? plist_add+0xbe/0x100 ? exc_page_fault+0x7c/0x180 ? asm_exc_page_fault+0x26/0x30 ? drm_dp_atomic_find_time_slots+0x5e/0x260 [drm_display_helper 0e67723696438d8e02b741593dd50d80b44c2026] ? drm_dp_atomic_find_time_slots+0x28/0x260 [drm_display_helper 0e67723696438d8e02b741593dd50d80b44c2026] compute_mst_dsc_configs_for_link+0x2ff/0xa40 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054] ? fill_plane_buffer_attributes+0x419/0x510 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054] compute_mst_dsc_configs_for_state+0x1e1/0x250 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054] amdgpu_dm_atomic_check+0xecd/0x1190 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054] drm_atomic_check_only+0x5c5/0xa40 drm_mode_atomic_ioctl+0x76e/0xbc0 ? _copy_to_user+0x25/0x30 ? drm_ioctl+0x296/0x4b0 ? __pfx_drm_mode_atomic_ioctl+0x10/0x10 drm_ioctl_kernel+0xcd/0x170 drm_ioctl+0x26d/0x4b0 ? __pfx_drm_mode_atomic_ioctl+0x10/0x10 amdgpu_drm_ioctl+0x4e/0x90 [amdgpu 62e600d2a75e9158e1cd0a243bdc8e6da040c054] __x64_sys_ioctl+0x94/0xd0 do_syscall_64+0x60/0x90 ? do_syscall_64+0x6c/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7f4dad17f76f Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <89> c> RSP: 002b:00007ffd9ae859f0 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 000055e255a55900 RCX: 00007f4dad17f76f RDX: 00007ffd9ae85a90 RSI: 00000000c03864bc RDI: 000000000000000b RBP: 00007ffd9ae85a90 R08: 0000000000000003 R09: 0000000000000003 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000c03864bc R13: 000000000000000b R14: 000055e255a7fc60 R15: 000055e255a01eb0 </TASK> Modules linked in: rfcomm snd_seq_dummy snd_hrtimer snd_seq snd_seq_device ccm cmac algif_hash algif_skcipher af_alg joydev mousedev bnep > typec libphy k10temp ipmi_msghandler roles i2c_scmi acpi_cpufreq mac_hid nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_mas> CR2: 0000000000000008 ---[ end trace 0000000000000000 ]--- RIP: 0010:drm_dp_atomic_find_time_slots+0x5e/0x260 [drm_display_helper] Code: 01 00 00 48 8b 85 60 05 00 00 48 63 80 88 00 00 00 3b 43 28 0f 8d 2e 01 00 00 48 8b 53 30 48 8d 04 80 48 8d 04 c2 48 8b 40 18 <48> 8> RSP: 0018:ffff960cc2df77d8 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffff8afb87e81280 RCX: 0000000000000224 RDX: ffff8afb9ee37c00 RSI: ffff8afb8da1a578 RDI: ffff8afb87e81280 RBP: ffff8afb83d67000 R08: 0000000000000001 R09: ffff8afb9652f850 R10: ffff960cc2df7908 R11: 0000000000000002 R12: 0000000000000000 R13: ffff8afb8d7688a0 R14: ffff8afb8da1a578 R15: 0000000000000224 FS: 00007f4dac35ce00(0000) GS:ffff8afe30b00000(0000 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: cpu: Re-enable CPU mitigations by default for !X86 architectures Rename x86's to CPU_MITIGATIONS, define it in generic code, and force it on for all architectures exception x86. A recent commit to turn mitigations off by default if SPECULATION_MITIGATIONS=n kinda sorta missed that "cpu_mitigations" is completely generic, whereas SPECULATION_MITIGATIONS is x86-specific. Rename x86's SPECULATIVE_MITIGATIONS instead of keeping both and have it select CPU_MITIGATIONS, as having two configs for the same thing is unnecessary and confusing. This will also allow x86 to use the knob to manage mitigations that aren't strictly related to speculative execution. Use another Kconfig to communicate to common code that CPU_MITIGATIONS is already defined instead of having x86's menu depend on the common CPU_MITIGATIONS. This allows keeping a single point of contact for all of x86's mitigations, and it's not clear that other architectures *want* to allow disabling mitigations at compile-time.

In the Linux kernel, the following vulnerability has been resolved: fbmon: prevent division by zero in fb_videomode_from_videomode() The expression htotal * vtotal can have a zero value on overflow. It is necessary to prevent division by zero like in fb_var_to_videomode(). Found by Linux Verification Center (linuxtesting.org) with Svace.

In the Linux kernel, the following vulnerability has been resolved: net: atlantic: Fix DMA mapping for PTP hwts ring Function aq_ring_hwts_rx_alloc() maps extra AQ_CFG_RXDS_DEF bytes for PTP HWTS ring but then generic aq_ring_free() does not take this into account. Create and use a specific function to free HWTS ring to fix this issue. Trace: [ 215.351607] ------------[ cut here ]------------ [ 215.351612] DMA-API: atlantic 0000:4b:00.0: device driver frees DMA memory with different size [device address=0x00000000fbdd0000] [map size=34816 bytes] [unmap size=32768 bytes] [ 215.351635] WARNING: CPU: 33 PID: 10759 at kernel/dma/debug.c:988 check_unmap+0xa6f/0x2360 ... [ 215.581176] Call Trace: [ 215.583632] <TASK> [ 215.585745] ? show_trace_log_lvl+0x1c4/0x2df [ 215.590114] ? show_trace_log_lvl+0x1c4/0x2df [ 215.594497] ? debug_dma_free_coherent+0x196/0x210 [ 215.599305] ? check_unmap+0xa6f/0x2360 [ 215.603147] ? __warn+0xca/0x1d0 [ 215.606391] ? check_unmap+0xa6f/0x2360 [ 215.610237] ? report_bug+0x1ef/0x370 [ 215.613921] ? handle_bug+0x3c/0x70 [ 215.617423] ? exc_invalid_op+0x14/0x50 [ 215.621269] ? asm_exc_invalid_op+0x16/0x20 [ 215.625480] ? check_unmap+0xa6f/0x2360 [ 215.629331] ? mark_lock.part.0+0xca/0xa40 [ 215.633445] debug_dma_free_coherent+0x196/0x210 [ 215.638079] ? __pfx_debug_dma_free_coherent+0x10/0x10 [ 215.643242] ? slab_free_freelist_hook+0x11d/0x1d0 [ 215.648060] dma_free_attrs+0x6d/0x130 [ 215.651834] aq_ring_free+0x193/0x290 [atlantic] [ 215.656487] aq_ptp_ring_free+0x67/0x110 [atlantic] ... [ 216.127540] ---[ end trace 6467e5964dd2640b ]--- [ 216.132160] DMA-API: Mapped at: [ 216.132162] debug_dma_alloc_coherent+0x66/0x2f0 [ 216.132165] dma_alloc_attrs+0xf5/0x1b0 [ 216.132168] aq_ring_hwts_rx_alloc+0x150/0x1f0 [atlantic] [ 216.132193] aq_ptp_ring_alloc+0x1bb/0x540 [atlantic] [ 216.132213] aq_nic_init+0x4a1/0x760 [atlantic]

A use-after-free flaw was found in the Linux kernel’s core dump subsystem. This flaw allows a local user to crash the system. Only if patch 390031c94211 ("coredump: Use the vma snapshot in fill_files_note") not applied yet, then kernel could be affected.

In the Linux kernel, the following vulnerability has been resolved: riscv/kprobe: fix kernel panic when invoking sys_read traced by kprobe The execution of sys_read end up hitting a BUG_ON() in __find_get_block after installing kprobe at sys_read, the BUG message like the following: [ 65.708663] ------------[ cut here ]------------ [ 65.709987] kernel BUG at fs/buffer.c:1251! [ 65.711283] Kernel BUG [#1] [ 65.712032] Modules linked in: [ 65.712925] CPU: 0 PID: 51 Comm: sh Not tainted 5.12.0-rc4 #1 [ 65.714407] Hardware name: riscv-virtio,qemu (DT) [ 65.715696] epc : __find_get_block+0x218/0x2c8 [ 65.716835] ra : __getblk_gfp+0x1c/0x4a [ 65.717831] epc : ffffffe00019f11e ra : ffffffe00019f56a sp : ffffffe002437930 [ 65.719553] gp : ffffffe000f06030 tp : ffffffe0015abc00 t0 : ffffffe00191e038 [ 65.721290] t1 : ffffffe00191e038 t2 : 000000000000000a s0 : ffffffe002437960 [ 65.723051] s1 : ffffffe00160ad00 a0 : ffffffe00160ad00 a1 : 000000000000012a [ 65.724772] a2 : 0000000000000400 a3 : 0000000000000008 a4 : 0000000000000040 [ 65.726545] a5 : 0000000000000000 a6 : ffffffe00191e000 a7 : 0000000000000000 [ 65.728308] s2 : 000000000000012a s3 : 0000000000000400 s4 : 0000000000000008 [ 65.730049] s5 : 000000000000006c s6 : ffffffe00240f800 s7 : ffffffe000f080a8 [ 65.731802] s8 : 0000000000000001 s9 : 000000000000012a s10: 0000000000000008 [ 65.733516] s11: 0000000000000008 t3 : 00000000000003ff t4 : 000000000000000f [ 65.734434] t5 : 00000000000003ff t6 : 0000000000040000 [ 65.734613] status: 0000000000000100 badaddr: 0000000000000000 cause: 0000000000000003 [ 65.734901] Call Trace: [ 65.735076] [<ffffffe00019f11e>] __find_get_block+0x218/0x2c8 [ 65.735417] [<ffffffe00020017a>] __ext4_get_inode_loc+0xb2/0x2f6 [ 65.735618] [<ffffffe000201b6c>] ext4_get_inode_loc+0x3a/0x8a [ 65.735802] [<ffffffe000203380>] ext4_reserve_inode_write+0x2e/0x8c [ 65.735999] [<ffffffe00020357a>] __ext4_mark_inode_dirty+0x4c/0x18e [ 65.736208] [<ffffffe000206bb0>] ext4_dirty_inode+0x46/0x66 [ 65.736387] [<ffffffe000192914>] __mark_inode_dirty+0x12c/0x3da [ 65.736576] [<ffffffe000180dd2>] touch_atime+0x146/0x150 [ 65.736748] [<ffffffe00010d762>] filemap_read+0x234/0x246 [ 65.736920] [<ffffffe00010d834>] generic_file_read_iter+0xc0/0x114 [ 65.737114] [<ffffffe0001f5d7a>] ext4_file_read_iter+0x42/0xea [ 65.737310] [<ffffffe000163f2c>] new_sync_read+0xe2/0x15a [ 65.737483] [<ffffffe000165814>] vfs_read+0xca/0xf2 [ 65.737641] [<ffffffe000165bae>] ksys_read+0x5e/0xc8 [ 65.737816] [<ffffffe000165c26>] sys_read+0xe/0x16 [ 65.737973] [<ffffffe000003972>] ret_from_syscall+0x0/0x2 [ 65.738858] ---[ end trace fe93f985456c935d ]--- A simple reproducer looks like: echo 'p:myprobe sys_read fd=%a0 buf=%a1 count=%a2' > /sys/kernel/debug/tracing/kprobe_events echo 1 > /sys/kernel/debug/tracing/events/kprobes/myprobe/enable cat /sys/kernel/debug/tracing/trace Here's what happens to hit that BUG_ON(): 1) After installing kprobe at entry of sys_read, the first instruction is replaced by 'ebreak' instruction on riscv64 platform. 2) Once kernel reach the 'ebreak' instruction at the entry of sys_read, it trap into the riscv breakpoint handler, where it do something to setup for coming single-step of origin instruction, including backup the 'sstatus' in pt_regs, followed by disable interrupt during single stepping via clear 'SIE' bit of 'sstatus' in pt_regs. 3) Then kernel restore to the instruction slot contains two instructions, one is original instruction at entry of sys_read, the other is 'ebreak'. Here it trigger a 'Instruction page fault' exception (value at 'scause' is '0xc'), if PF is not filled into PageTabe for that slot yet. 4) Again kernel trap into page fault exception handler, where it choose different policy according to the state of running kprobe. Because afte 2) the state is KPROBE_HIT_SS, so kernel reset the current kp ---truncated---

The Linux kernel io_uring IORING_OP_SOCKET operation contained a double free in function __sys_socket_file() in file net/socket.c. This issue was introduced in da214a475f8bd1d3e9e7a19ddfeb4d1617551bab and fixed in 649c15c7691e9b13cbe9bf6c65c365350e056067.

In the Linux kernel, the following vulnerability has been resolved: KVM: SVM: Use online_vcpus, not created_vcpus, to iterate over vCPUs Use the kvm_for_each_vcpu() helper to iterate over vCPUs when encrypting VMSAs for SEV, which effectively switches to use online_vcpus instead of created_vcpus. This fixes a possible null-pointer dereference as created_vcpus does not guarantee a vCPU exists, since it is updated at the very beginning of KVM_CREATE_VCPU. created_vcpus exists to allow the bulk of vCPU creation to run in parallel, while still correctly restricting the max number of max vCPUs.

A memory leak flaw was found in the Linux kernel's Stream Control Transmission Protocol. This issue may occur when a user starts a malicious networking service and someone connects to this service. This could allow a local user to starve resources, causing a denial of service.

An issue was discovered in the Linux kernel before 5.11.11. The netfilter subsystem allows attackers to cause a denial of service (panic) because net/netfilter/x_tables.c and include/linux/netfilter/x_tables.h lack a full memory barrier upon the assignment of a new table value, aka CID-175e476b8cdf.

In the Linux kernel, the following vulnerability has been resolved: mlxsw: spectrum_acl_tcam: Fix incorrect list API usage Both the function that migrates all the chunks within a region and the function that migrates all the entries within a chunk call list_first_entry() on the respective lists without checking that the lists are not empty. This is incorrect usage of the API, which leads to the following warning [1]. Fix by returning if the lists are empty as there is nothing to migrate in this case. [1] WARNING: CPU: 0 PID: 6437 at drivers/net/ethernet/mellanox/mlxsw/spectrum_acl_tcam.c:1266 mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0> Modules linked in: CPU: 0 PID: 6437 Comm: kworker/0:37 Not tainted 6.9.0-rc3-custom-00883-g94a65f079ef6 #39 Hardware name: Mellanox Technologies Ltd. MSN3700/VMOD0005, BIOS 5.11 01/06/2019 Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work RIP: 0010:mlxsw_sp_acl_tcam_vchunk_migrate_all+0x1f1/0x2c0 [...] Call Trace: <TASK> mlxsw_sp_acl_tcam_vregion_rehash_work+0x6c/0x4a0 process_one_work+0x151/0x370 worker_thread+0x2cb/0x3e0 kthread+0xd0/0x100 ret_from_fork+0x34/0x50 ret_from_fork_asm+0x1a/0x30 </TASK>

In the Linux kernel, the following vulnerability has been resolved: block: fix q->blkg_list corruption during disk rebind Multiple gendisk instances can allocated/added for single request queue in case of disk rebind. blkg may still stay in q->blkg_list when calling blkcg_init_disk() for rebind, then q->blkg_list becomes corrupted. Fix the list corruption issue by: - add blkg_init_queue() to initialize q->blkg_list & q->blkcg_mutex only - move calling blkg_init_queue() into blk_alloc_queue() The list corruption should be started since commit f1c006f1c685 ("blk-cgroup: synchronize pd_free_fn() from blkg_free_workfn() and blkcg_deactivate_policy()") which delays removing blkg from q->blkg_list into blkg_free_workfn().