Certain NETGEAR devices are affected by command injection by an unauthenticated attacker. This affects D7000v2 before 1.0.0.74, LAX20 before 1.1.6.28, MK62 before 1.0.6.116, MR60 before 1.0.6.116, MS60 before 1.0.6.116, RAX15 before 1.0.3.96, RAX20 before 1.0.3.96, RAX200 before 1.0.4.120, RAX45 before 1.0.3.96, RAX50 before 1.0.3.96, RAX43 before 1.0.3.96, RAX40v2 before 1.0.3.96, RAX35v2 before 1.0.3.96, RAX75 before 1.0.4.120, RAX80 before 1.0.4.120, RBK752 before 3.2.17.12, RBR750 before 3.2.17.12, RBS750 before 3.2.17.12, RBK852 before 3.2.17.12, RBR850 before 3.2.17.12, RBS850 before 3.2.17.12, and XR1000 before 1.0.0.58.

Certain NETGEAR devices are affected by incorrect configuration of security settings. This affects RBS50Y before 2.7.0.122, SRK60 before 2.7.0.122, SRR60 before 2.7.0.122, SRS60 before 2.7.0.122, SXK30 before 3.2.33.108, SXR30 before 3.2.33.108, SXS30 before 3.2.33.108, and SRC60 before 2.7.0.122.

Certain NETGEAR devices are affected by a stack-based buffer overflow by an unauthenticated attacker. This affects D6220 before 1.0.0.68, D6400 before 1.0.0.102, D7000v2 before 1.0.0.74, D8500 before 1.0.3.60, DC112A before 1.0.0.56, R6300v2 before 1.0.4.50, R6400 before 1.0.1.68, R7000 before 1.0.11.116, R7100LG before 1.0.0.70, RBS40V before 2.6.2.8, RBW30 before 2.6.2.2, RS400 before 1.5.1.80, R7000P before 1.3.2.132, and R6900P before 1.3.2.132.

NETGEAR D7000 devices before 1.0.1.82 are affected by authentication bypass.

Certain NETGEAR devices are affected by command injection by an unauthenticated attacker. This affects XR300 before 1.0.3.68, R7000P before 1.3.3.140, and R6900P before 1.3.3.140.

NETGEAR JNR1010 devices before 1.0.0.32 have Incorrect Access Control because the ok value of the auth cookie is a special case.

Certain NETGEAR devices are affected by authentication bypass. This affects CBR40 before 2.5.0.24, CBR750 before 4.6.3.6, RBR852 before 3.2.17.12, RBR850 before 3.2.17.12, and RBS850 before 3.2.17.12.

Certain NETGEAR devices are affected by incorrect configuration of security settings. This affects AC2100 before 1.2.0.88, AC2400 before 1.2.0.88, AC2600 before 1.2.0.88, R6220 before 1.1.0.110, R6230 before 1.1.0.110, R6260 before 1.1.0.84, R6330 before 1.1.0.84, R6350 before 1.1.0.84, R6700v2 before 1.2.0.88, R6800 before 1.2.0.88, R6850 before 1.1.0.84, R6900v2 before 1.2.0.88, R7200 before 1.2.0.88, R7350 before 1.2.0.88, R7400 before 1.2.0.88, and R7450 before 1.2.0.88.

NETGEAR R6700v2 devices before 1.2.0.88 are affected by authentication bypass.

NETGEAR RAX200 devices before 1.0.5.132 are affected by insecure code.

Certain NETGEAR smart switches are affected by a remote admin password change by an unauthenticated attacker via the (disabled by default) /sqfs/bin/sccd daemon, which fails to check authentication when the authentication TLV is missing from a received NSDP packet. This affects GC108P before 1.0.8.2, GC108PP before 1.0.8.2, GS108Tv3 before 7.0.7.2, GS110TPP before 7.0.7.2, GS110TPv3 before 7.0.7.2, GS110TUP before 1.0.5.3, GS308T before 1.0.3.2, GS310TP before 1.0.3.2, GS710TUP before 1.0.5.3, GS716TP before 1.0.4.2, GS716TPP before 1.0.4.2, GS724TPP before 2.0.6.3, GS724TPv2 before 2.0.6.3, GS728TPPv2 before 6.0.8.2, GS728TPv2 before 6.0.8.2, GS750E before 1.0.1.10, GS752TPP before 6.0.8.2, GS752TPv2 before 6.0.8.2, MS510TXM before 1.0.4.2, and MS510TXUP before 1.0.4.2.

Certain NETGEAR devices are affected by lack of access control at the function level. This affects D6220 before 1.0.0.48, D6400 before 1.0.0.82, D7000v2 before 1.0.0.52, D7800 before 1.0.1.44, D8500 before 1.0.3.43, DC112A before 1.0.0.40, DGN2200v4 before 1.0.0.108, RBK50 before 2.3.0.32, RBR50 before 2.3.0.32, RBS50 before 2.3.0.32, RBK20 before 2.3.0.28, RBR20 before 2.3.0.28, RBS20 before 2.3.0.28, RBK40 before 2.3.0.28, RBR40 before 2.3.0.28, RBS40 before 2.3.0.28, R6020 before 1.0.0.34, R6080 before 1.0.0.34, R6120 before 1.0.0.44, R6220 before 1.1.0.80, R6230 before 1.1.0.80, R6250 before 1.0.4.34, R6260 before 1.1.0.40, R6850 before 1.1.0.40, R6350 before 1.1.0.40, R6400v2 before 1.0.2.62, R6700v3 before 1.0.2.62, R6700v2 before 1.2.0.36, R6800 before 1.2.0.36, R6900v2 before 1.2.0.36, R7000 before 1.0.9.34, R6900P before 1.3.1.44, R7000P before 1.3.1.44, R7100LG before 1.0.0.48, R7200 before 1.2.0.48, R7350 before 1.2.0.48, R7400 before 1.2.0.48, R7450 before 1.2.0.36, AC2100 before 1.2.0.36, AC2400 before 1.2.0.36, AC2600 before 1.2.0.36, R7500v2 before 1.0.3.38, R7800 before 1.0.2.58, R7900 before 1.0.3.8, R7960P before 1.4.1.44, R8000 before 1.0.4.28, R7900P before 1.4.1.30, R8000P before 1.4.1.30, R8900 before 1.0.4.2, R9000 before 1.0.4.2, RAX120 before 1.0.0.74, RBK752 before 3.2.16.6, RBR750 before 3.2.16.6, RBS750 before 3.2.16.6, RBK852 before 3.2.16.6, RBR850 before 3.2.16.6, RBS850 before 3.2.16.6, WNR3500Lv2 before 1.2.0.56, XR450 before 2.3.2.32, and XR500 before 2.3.2.32.

Certain NETGEAR devices are affected by command injection by an unauthenticated attacker. This affects CBR40 before 2.5.0.14, EX6100v2 before 1.0.1.98, EX6150v2 before 1.0.1.98, EX6250 before 1.0.0.132, EX6400 before 1.0.2.158, EX6400v2 before 1.0.0.132, EX6410 before 1.0.0.132, EX6420 before 1.0.0.132, EX7300 before 1.0.2.158, EX7300v2 before 1.0.0.132, EX7320 before 1.0.0.132, EX7700 before 1.0.0.216, EX8000 before 1.0.1.232, R7800 before 1.0.2.78, RBK12 before 2.6.1.44, RBR10 before 2.6.1.44, RBS10 before 2.6.1.44, RBK20 before 2.6.1.38, RBR20 before 2.6.1.36, RBS20 before 2.6.1.38, RBK40 before 2.6.1.38, RBR40 before 2.6.1.36, RBS40 before 2.6.1.38, RBK50 before 2.6.1.40, RBR50 before 2.6.1.40, RBS50 before 2.6.1.40, RBK752 before 3.2.16.6, RBR750 before 3.2.16.6, RBS750 before 3.2.16.6, RBK852 before 3.2.16.6, RBR850 before 3.2.16.6, RBS850 before 3.2.16.6, RBS40V before 2.6.2.4, RBS50Y before 2.6.1.40, RBW30 before 2.6.2.2, and XR500 before 2.3.2.114.

Certain NETGEAR devices are affected by command injection by an unauthenticated attacker. This affects D8500 before 1.0.3.58, R6900P before 1.3.2.132, R7000P before 1.3.2.132, R7100LG before 1.0.0.64, WNDR3400v3 before 1.0.1.38, and XR300 before 1.0.3.56.

The NETGEAR Insight application before 2.42 for Android and iOS is affected by password mismanagement.

NETGEAR ProSAFE Network Management System has Java Debug Wire Protocol (JDWP) listening on port 11611 and it is remotely accessible by unauthenticated users, allowing attackers to execute arbitrary code.

A Command Injection vulnerability exists in NETGEAR WNR2000v4 version 1.0.0.70. When using HTTP for SOAP authentication, command execution occurs during the process after successful authentication.

This vulnerability allows remote attackers to execute arbitrary code on affected installations of NETGEAR ProSAFE Network Management System 1.6.0.26. Authentication is not required to exploit this vulnerability. The specific flaw exists within the MFileUploadController class. The issue results from the lack of proper validation of a user-supplied path prior to using it in file operations. An attacker can leverage this vulnerability to execute code in the context of SYSTEM. Was ZDI-CAN-12124.

Certain NETGEAR devices are affected by command injection by an unauthenticated attacker. This affects R6400v2 before 1.0.4.84, R6700 before 1.0.2.8, R6700v3 before 1.0.4.84, R6900 before 1.0.2.8, and R7900 before 1.0.3.10.

NETGEAR R7800 devices before 1.0.2.68 are affected by remote code execution by unauthenticated attackers.

Netgear R7000P V1.3.0.8 is vulnerable to Buffer Overflow in /usr/sbin/httpd via parameter enable_band_steering.

Netgear R7000P V1.3.1.64 is vulnerable to Buffer Overflow via parameter openvpn_server_ip.

Netgear R7000P V1.3.1.64 is vulnerable to Buffer Overflow via parameter openvpn_push1.

Netgear R7000P V1.3.1.64 is vulnerable to Buffer Overflow via parameters KEY1 and KEY2.

Certain NETGEAR devices are affected by authentication bypass. This affects WAC505 before 5.0.0.17 and WAC510 before 5.0.0.17.

An issue was discovered on NETGEAR WNR1000V4 1.1.0.54 devices. The web management interface (setup.cgi) has an authentication bypass and other problems that ultimately allow an attacker to remotely compromise the device from a malicious webpage. The attacker sends an FW_remote.htm&todo=cfg_init request without a cookie, reads the Set-Cookie header in the 401 Unauthorized response, and then repeats the FW_remote.htm&todo=cfg_init request with the specified cookie.

A Symlink Traversal vulnerability exists in NETGEAR Centria WNDR4700 Firmware 1.0.0.34.

Certain NETGEAR devices are affected by a stack-based buffer overflow by an unauthenticated attacker. This affects WAC505 before 5.0.5.4, WAC510 before 5.0.5.4, WAC120 before 2.1.7, WN604 before 3.3.10, WNAP320 before 3.7.11.4, WNAP210v2 before 3.7.11.4, WNDAP350 before 3.7.11.4, WNDAP360 before 3.7.11.4, WNDAP660 before 3.7.11.4, WNDAP620 before 2.1.7, and WND930 before 2.1.5.

Certain NETGEAR devices are affected by a stack-based buffer overflow by an unauthenticated attacker. This affects WAC505 before 5.0.0.17 and WAC510 before 5.0.0.17.

Symlink Traversal vulnerability in NETGEAR WNR3500U and WNR3500L due to misconfiguration in the SMB service.

Netgear WNR1000v3 with firmware before 1.0.2.60 contains an Authentication Bypass via the NtgrBak key.

An Authentication Bypass vulnerability exists in NETGEAR Centria WNDR4700 Firmware 1.0.0.34 in http://<router_ip>/apply.cgi?/hdd_usr_setup.htm that when visited by any user, authenticated or not, causes the router to no longer require a password to access the web administration portal.

A vulnerability was found in Netgear WNR614 1.1.0.28_1.0.1WW. It has been classified as critical. This affects an unknown part of the component URL Handler. The manipulation with the input %00currentsetting.htm leads to improper authentication. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. This issue appears to have been circulating as an 0day since 2024.

A vulnerability, which was classified as very critical, was found in Netgear DGND3700 1.1.00.15_1.00.15NA. This affects an unknown part of the file /BRS_top.html of the component Basic Authentication. The manipulation leads to improper authentication. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. Other products might be affected as well. The vendor was contacted early about this disclosure.

Certain NETGEAR devices are affected by a stack-based buffer overflow by an unauthenticated attacker. This affects D3600 before 1.0.0.76, D6000 before 1.0.0.78, D6200 before 1.1.00.32, D7000 before 1.0.1.68, D7800 before 1.0.1.56, DM200 before 1.0.0.61, EX2700 before 1.0.1.52, EX6100v2 before 1.0.1.76, EX6150v2 before 1.0.1.76, EX6200v2 before 1.0.1.74, EX6400 before 1.0.2.140, EX7300 before 1.0.2.140, EX8000 before 1.0.1.186, JR6150 before 1.0.1.18, PR2000 before 1.0.0.28, R6020 before 1.0.0.38, R6050 before 1.0.1.18, R6080 before 1.0.0.38, R6120 before 1.0.0.46, R6220 before 1.1.0.80, R6230 before 1.1.0.80, R6260 before 1.1.0.40, R6700v2 before 1.2.0.36, R6800 before 1.2.0.36, R6900v2 before 1.2.0.36, R7500v2 before 1.0.3.40, R7800 before 1.0.2.62, R8900 before 1.0.4.12, R9000 before 1.0.4.12, RBK20 before 2.3.0.28, RBR20 before 2.3.0.28, RBS20 before 2.3.0.28, RBK40 before 2.3.0.28, RBR40 before 2.3.0.28, RBS40 before 2.3.0.28, RBK50 before 2.3.0.32, RBR50 before 2.3.0.32, RBS50 before 2.3.0.32, WN2000RPTv3 before 1.0.1.34, WN3000RPv2 before 1.0.0.78, WN3000RPv2 before 1.0.0.78, WN3000RPv3 before 1.0.2.78, WN3100RPv2 before 1.0.0.66, WNR2000v5 before 1.0.0.70, WNR2020 before 1.1.0.62, XR450 before 2.3.2.32, and XR500 before 2.3.2.32.

NETGEAR NMS300 devices before 1.6.0.27 are affected by command injection by an unauthenticated attacker.

Netgear EX8000 V1.0.0.126 is vulnerable to Command Injection via the Iface parameter in the action_wireless function.

In Netgear RAX30 V1.0.10.94, a PHP-FPM misconfiguration vulnerability is caused by not following the specification to only limit FPM to .php extensions. An attacker may exploit this by uploading malicious scripts disguised with alternate extensions and tricking the web server into executing them as PHP, bypassing security mechanisms based on file extension filtering. This may lead to remote code execution (RCE), information disclosure, or full system compromise.

(1) boardData102.php, (2) boardData103.php, (3) boardDataJP.php, (4) boardDataNA.php, and (5) boardDataWW.php in Netgear WN604 before 3.3.3 and WN802Tv2, WNAP210v2, WNAP320, WNDAP350, WNDAP360, and WNDAP660 before 3.5.5.0 allow remote attackers to execute arbitrary commands.

A vulnerability was found in Netgear JWNR2000v2 1.0.0.11. It has been declared as critical. Affected by this vulnerability is the function cmd_wireless. The manipulation of the argument host leads to command injection. The attack can be launched remotely. The vendor was contacted early about this disclosure but did not respond in any way.

Certain NETGEAR devices are affected by authentication bypass. This affects D6200 before 1.1.00.36, D7000 before 1.0.1.74, PR2000 before 1.0.0.30, R6020 before 1.0.0.42, R6050 before 1.0.1.22, JR6150 before 1.0.1.22, R6080 before 1.0.0.42, R6120 before 1.0.0.66, R6220 before 1.1.0.100, R6230 before 1.1.0.100, R6260 before 1.1.0.64, R6700v2 before 1.2.0.62, R6800 before 1.2.0.62, R69002 before 1.2.0.62, and WNR2020 before 1.1.0.62.

Certain NETGEAR devices are affected by authentication bypass. This affects D6200 before 1.1.00.40, D7000 before 1.0.1.78, R6020 before 1.0.0.42, R6080 before 1.0.0.42, R6050 before 1.0.1.26, JR6150 before 1.0.1.26, R6120 before 1.0.0.66, R6220 before 1.1.0.100, R6260 before 1.1.0.66, R6700v2 before 1.2.0.62, R6800 before 1.2.0.62, R6900v2 before 1.2.0.62, AC2100 before 1.2.0.62, AC2400 before 1.2.0.62, AC2600 before 1.2.0.62, R7450 before 1.2.0.62, and WNR2020 before 1.1.0.62.

NETGEAR JGS516PE devices before 2.6.0.43 are affected by lack of access control at the function level.

Netgear DC112A V1.0.0.64 has an OS command injection vulnerability in the usb_adv.cgi, which allows remote attackers to execute arbitrary commands via parameter "deviceName" passed to the binary through a POST request.

Netgear N300 wireless router wnr2000v4-V1.0.0.70 is vulnerable to Buffer Overflow via uhttpd. There is a stack overflow vulnerability caused by strcpy.

Netgear R7100LG 1.0.0.78 was discovered to contain a command injection vulnerability via the password parameter at usb_remote_invite.cgi.

NETGEAR ProSAFE Network Management System MyHandlerInterceptor Authentication Bypass Vulnerability. This vulnerability allows remote attackers to bypass authentication on affected installations of NETGEAR ProSAFE Network Management System. Authentication is not required to exploit this vulnerability. The specific flaw exists within the MyHandlerInterceptor class. The issue results from improper implementation of the authentication mechanism. An attacker can leverage this vulnerability to bypass authentication on the system. . Was ZDI-CAN-19718.