In the Linux kernel, the following vulnerability has been resolved: ptp: ocp: Limit signal/freq counts in summary output functions The debugfs summary output could access uninitialized elements in the freq_in[] and signal_out[] arrays, causing NULL pointer dereferences and triggering a kernel Oops (page_fault_oops). This patch adds u8 fields (nr_freq_in, nr_signal_out) to track the number of initialized elements, with a maximum of 4 per array. The summary output functions are updated to respect these limits, preventing out-of-bounds access and ensuring safe array handling. Widen the label variables because the change confuses GCC about max length of the strings.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: mv88e6xxx: fix -ENOENT when deleting VLANs and MST is unsupported Russell King reports that on the ZII dev rev B, deleting a bridge VLAN from a user port fails with -ENOENT: https://lore.kernel.org/netdev/Z_lQXNP0s5-IiJzd@shell.armlinux.org.uk/ This comes from mv88e6xxx_port_vlan_leave() -> mv88e6xxx_mst_put(), which tries to find an MST entry in &chip->msts associated with the SID, but fails and returns -ENOENT as such. But we know that this chip does not support MST at all, so that is not surprising. The question is why does the guard in mv88e6xxx_mst_put() not exit early: if (!sid) return 0; And the answer seems to be simple: the sid comes from vlan.sid which supposedly was previously populated by mv88e6xxx_vtu_get(). But some chip->info->ops->vtu_getnext() implementations do not populate vlan.sid, for example see mv88e6185_g1_vtu_getnext(). In that case, later in mv88e6xxx_port_vlan_leave() we are using a garbage sid which is just residual stack memory. Testing for sid == 0 covers all cases of a non-bridge VLAN or a bridge VLAN mapped to the default MSTI. For some chips, SID 0 is valid and installed by mv88e6xxx_stu_setup(). A chip which does not support the STU would implicitly only support mapping all VLANs to the default MSTI, so although SID 0 is not valid, it would be sufficient, if we were to zero-initialize the vlan structure, to fix the bug, due to the coincidence that a test for vlan.sid == 0 already exists and leads to the same (correct) behavior. Another option which would be sufficient would be to add a test for mv88e6xxx_has_stu() inside mv88e6xxx_mst_put(), symmetric to the one which already exists in mv88e6xxx_mst_get(). But that placement means the caller will have to dereference vlan.sid, which means it will access uninitialized memory, which is not nice even if it ignores it later. So we end up making both modifications, in order to not rely just on the sid == 0 coincidence, but also to avoid having uninitialized structure fields which might get temporarily accessed.

In the Linux kernel, the following vulnerability has been resolved: net: ch9200: fix uninitialised access during mii_nway_restart In mii_nway_restart() the code attempts to call mii->mdio_read which is ch9200_mdio_read(). ch9200_mdio_read() utilises a local buffer called "buff", which is initialised with control_read(). However "buff" is conditionally initialised inside control_read(): if (err == size) { memcpy(data, buf, size); } If the condition of "err == size" is not met, then "buff" remains uninitialised. Once this happens the uninitialised "buff" is accessed and returned during ch9200_mdio_read(): return (buff[0] | buff[1] << 8); The problem stems from the fact that ch9200_mdio_read() ignores the return value of control_read(), leading to uinit-access of "buff". To fix this we should check the return value of control_read() and return early on error.

In the Linux kernel, the following vulnerability has been resolved: netfilter: flowtable: account for Ethernet header in nf_flow_pppoe_proto() syzbot found a potential access to uninit-value in nf_flow_pppoe_proto() Blamed commit forgot the Ethernet header. BUG: KMSAN: uninit-value in nf_flow_offload_inet_hook+0x7e4/0x940 net/netfilter/nf_flow_table_inet.c:27 nf_flow_offload_inet_hook+0x7e4/0x940 net/netfilter/nf_flow_table_inet.c:27 nf_hook_entry_hookfn include/linux/netfilter.h:157 [inline] nf_hook_slow+0xe1/0x3d0 net/netfilter/core.c:623 nf_hook_ingress include/linux/netfilter_netdev.h:34 [inline] nf_ingress net/core/dev.c:5742 [inline] __netif_receive_skb_core+0x4aff/0x70c0 net/core/dev.c:5837 __netif_receive_skb_one_core net/core/dev.c:5975 [inline] __netif_receive_skb+0xcc/0xac0 net/core/dev.c:6090 netif_receive_skb_internal net/core/dev.c:6176 [inline] netif_receive_skb+0x57/0x630 net/core/dev.c:6235 tun_rx_batched+0x1df/0x980 drivers/net/tun.c:1485 tun_get_user+0x4ee0/0x6b40 drivers/net/tun.c:1938 tun_chr_write_iter+0x3e9/0x5c0 drivers/net/tun.c:1984 new_sync_write fs/read_write.c:593 [inline] vfs_write+0xb4b/0x1580 fs/read_write.c:686 ksys_write fs/read_write.c:738 [inline] __do_sys_write fs/read_write.c:749 [inline]

In the Linux kernel, the following vulnerability has been resolved: jfs: Fix uninit-value access of imap allocated in the diMount() function syzbot reports that hex_dump_to_buffer is using uninit-value: ===================================================== BUG: KMSAN: uninit-value in hex_dump_to_buffer+0x888/0x1100 lib/hexdump.c:171 hex_dump_to_buffer+0x888/0x1100 lib/hexdump.c:171 print_hex_dump+0x13d/0x3e0 lib/hexdump.c:276 diFree+0x5ba/0x4350 fs/jfs/jfs_imap.c:876 jfs_evict_inode+0x510/0x550 fs/jfs/inode.c:156 evict+0x723/0xd10 fs/inode.c:796 iput_final fs/inode.c:1946 [inline] iput+0x97b/0xdb0 fs/inode.c:1972 txUpdateMap+0xf3e/0x1150 fs/jfs/jfs_txnmgr.c:2367 txLazyCommit fs/jfs/jfs_txnmgr.c:2664 [inline] jfs_lazycommit+0x627/0x11d0 fs/jfs/jfs_txnmgr.c:2733 kthread+0x6b9/0xef0 kernel/kthread.c:464 ret_from_fork+0x6d/0x90 arch/x86/kernel/process.c:148 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Uninit was created at: slab_post_alloc_hook mm/slub.c:4121 [inline] slab_alloc_node mm/slub.c:4164 [inline] __kmalloc_cache_noprof+0x8e3/0xdf0 mm/slub.c:4320 kmalloc_noprof include/linux/slab.h:901 [inline] diMount+0x61/0x7f0 fs/jfs/jfs_imap.c:105 jfs_mount+0xa8e/0x11d0 fs/jfs/jfs_mount.c:176 jfs_fill_super+0xa47/0x17c0 fs/jfs/super.c:523 get_tree_bdev_flags+0x6ec/0x910 fs/super.c:1636 get_tree_bdev+0x37/0x50 fs/super.c:1659 jfs_get_tree+0x34/0x40 fs/jfs/super.c:635 vfs_get_tree+0xb1/0x5a0 fs/super.c:1814 do_new_mount+0x71f/0x15e0 fs/namespace.c:3560 path_mount+0x742/0x1f10 fs/namespace.c:3887 do_mount fs/namespace.c:3900 [inline] __do_sys_mount fs/namespace.c:4111 [inline] __se_sys_mount+0x71f/0x800 fs/namespace.c:4088 __x64_sys_mount+0xe4/0x150 fs/namespace.c:4088 x64_sys_call+0x39bf/0x3c30 arch/x86/include/generated/asm/syscalls_64.h:166 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f ===================================================== The reason is that imap is not properly initialized after memory allocation. It will cause the snprintf() function to write uninitialized data into linebuf within hex_dump_to_buffer(). Fix this by using kzalloc instead of kmalloc to clear its content at the beginning in diMount().

In the Linux kernel, the following vulnerability has been resolved: pptp: ensure minimal skb length in pptp_xmit() Commit aabc6596ffb3 ("net: ppp: Add bound checking for skb data on ppp_sync_txmung") fixed ppp_sync_txmunge() We need a similar fix in pptp_xmit(), otherwise we might read uninit data as reported by syzbot. BUG: KMSAN: uninit-value in pptp_xmit+0xc34/0x2720 drivers/net/ppp/pptp.c:193 pptp_xmit+0xc34/0x2720 drivers/net/ppp/pptp.c:193 ppp_channel_bridge_input drivers/net/ppp/ppp_generic.c:2290 [inline] ppp_input+0x1d6/0xe60 drivers/net/ppp/ppp_generic.c:2314 pppoe_rcv_core+0x1e8/0x760 drivers/net/ppp/pppoe.c:379 sk_backlog_rcv+0x142/0x420 include/net/sock.h:1148 __release_sock+0x1d3/0x330 net/core/sock.c:3213 release_sock+0x6b/0x270 net/core/sock.c:3767 pppoe_sendmsg+0x15d/0xcb0 drivers/net/ppp/pppoe.c:904 sock_sendmsg_nosec net/socket.c:712 [inline] __sock_sendmsg+0x330/0x3d0 net/socket.c:727 ____sys_sendmsg+0x893/0xd80 net/socket.c:2566 ___sys_sendmsg+0x271/0x3b0 net/socket.c:2620 __sys_sendmmsg+0x2d9/0x7c0 net/socket.c:2709

An information disclosure vulnerability exists in the ARM SIGPAGE functionality of Linux Kernel v5.4.66 and v5.4.54. The latest version (5.11-rc4) seems to still be vulnerable. A userland application can read the contents of the sigpage, which can leak kernel memory contents. An attacker can read a process’s memory at a specific offset to trigger this vulnerability. This was fixed in kernel releases: 4.14.222 4.19.177 5.4.99 5.10.17 5.11

In the Linux kernel, the following vulnerability has been resolved: wifi: brcm80211: fmac: Add error handling for brcmf_usb_dl_writeimage() The function brcmf_usb_dl_writeimage() calls the function brcmf_usb_dl_cmd() but dose not check its return value. The 'state.state' and the 'state.bytes' are uninitialized if the function brcmf_usb_dl_cmd() fails. It is dangerous to use uninitialized variables in the conditions. Add error handling for brcmf_usb_dl_cmd() to jump to error handling path if the brcmf_usb_dl_cmd() fails and the 'state.state' and the 'state.bytes' are uninitialized. Improve the error message to report more detailed error information.

In the Linux kernel, the following vulnerability has been resolved: sched_ext: bpf_iter_scx_dsq_new() should always initialize iterator BPF programs may call next() and destroy() on BPF iterators even after new() returns an error value (e.g. bpf_for_each() macro ignores error returns from new()). bpf_iter_scx_dsq_new() could leave the iterator in an uninitialized state after an error return causing bpf_iter_scx_dsq_next() to dereference garbage data. Make bpf_iter_scx_dsq_new() always clear $kit->dsq so that next() and destroy() become noops.

In the Linux kernel, the following vulnerability has been resolved: mtd: nand: ecc-mxic: Fix use of uninitialized variable ret If ctx->steps is zero, the loop processing ECC steps is skipped, and the variable ret remains uninitialized. It is later checked and returned, which leads to undefined behavior and may cause unpredictable results in user space or kernel crashes. This scenario can be triggered in edge cases such as misconfigured geometry, ECC engine misuse, or if ctx->steps is not validated after initialization. Initialize ret to zero before the loop to ensure correct and safe behavior regardless of the ctx->steps value. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: libnvdimm/labels: Fix divide error in nd_label_data_init() If a faulty CXL memory device returns a broken zero LSA size in its memory device information (Identify Memory Device (Opcode 4000h), CXL spec. 3.1, 8.2.9.9.1.1), a divide error occurs in the libnvdimm driver: Oops: divide error: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:nd_label_data_init+0x10e/0x800 [libnvdimm] Code and flow: 1) CXL Command 4000h returns LSA size = 0 2) config_size is assigned to zero LSA size (CXL pmem driver): drivers/cxl/pmem.c: .config_size = mds->lsa_size, 3) max_xfer is set to zero (nvdimm driver): drivers/nvdimm/label.c: max_xfer = min_t(size_t, ndd->nsarea.max_xfer, config_size); 4) A subsequent DIV_ROUND_UP() causes a division by zero: drivers/nvdimm/label.c: /* Make our initial read size a multiple of max_xfer size */ drivers/nvdimm/label.c: read_size = min(DIV_ROUND_UP(read_size, max_xfer) * max_xfer, drivers/nvdimm/label.c- config_size); Fix this by checking the config size parameter by extending an existing check.

In the Linux kernel, the following vulnerability has been resolved: KVM: arm64: Fix uninitialized memcache pointer in user_mem_abort() Commit fce886a60207 ("KVM: arm64: Plumb the pKVM MMU in KVM") made the initialization of the local memcache variable in user_mem_abort() conditional, leaving a codepath where it is used uninitialized via kvm_pgtable_stage2_map(). This can fail on any path that requires a stage-2 allocation without transition via a permission fault or dirty logging. Fix this by making sure that memcache is always valid.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_reject_ipv6: fix nf_reject_ip6_tcphdr_put() syzbot reported that nf_reject_ip6_tcphdr_put() was possibly sending garbage on the four reserved tcp bits (th->res1) Use skb_put_zero() to clear the whole TCP header, as done in nf_reject_ip_tcphdr_put() BUG: KMSAN: uninit-value in nf_reject_ip6_tcphdr_put+0x688/0x6c0 net/ipv6/netfilter/nf_reject_ipv6.c:255 nf_reject_ip6_tcphdr_put+0x688/0x6c0 net/ipv6/netfilter/nf_reject_ipv6.c:255 nf_send_reset6+0xd84/0x15b0 net/ipv6/netfilter/nf_reject_ipv6.c:344 nft_reject_inet_eval+0x3c1/0x880 net/netfilter/nft_reject_inet.c:48 expr_call_ops_eval net/netfilter/nf_tables_core.c:240 [inline] nft_do_chain+0x438/0x22a0 net/netfilter/nf_tables_core.c:288 nft_do_chain_inet+0x41a/0x4f0 net/netfilter/nft_chain_filter.c:161 nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline] nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626 nf_hook include/linux/netfilter.h:269 [inline] NF_HOOK include/linux/netfilter.h:312 [inline] ipv6_rcv+0x29b/0x390 net/ipv6/ip6_input.c:310 __netif_receive_skb_one_core net/core/dev.c:5661 [inline] __netif_receive_skb+0x1da/0xa00 net/core/dev.c:5775 process_backlog+0x4ad/0xa50 net/core/dev.c:6108 __napi_poll+0xe7/0x980 net/core/dev.c:6772 napi_poll net/core/dev.c:6841 [inline] net_rx_action+0xa5a/0x19b0 net/core/dev.c:6963 handle_softirqs+0x1ce/0x800 kernel/softirq.c:554 __do_softirq+0x14/0x1a kernel/softirq.c:588 do_softirq+0x9a/0x100 kernel/softirq.c:455 __local_bh_enable_ip+0x9f/0xb0 kernel/softirq.c:382 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:908 [inline] __dev_queue_xmit+0x2692/0x5610 net/core/dev.c:4450 dev_queue_xmit include/linux/netdevice.h:3105 [inline] neigh_resolve_output+0x9ca/0xae0 net/core/neighbour.c:1565 neigh_output include/net/neighbour.h:542 [inline] ip6_finish_output2+0x2347/0x2ba0 net/ipv6/ip6_output.c:141 __ip6_finish_output net/ipv6/ip6_output.c:215 [inline] ip6_finish_output+0xbb8/0x14b0 net/ipv6/ip6_output.c:226 NF_HOOK_COND include/linux/netfilter.h:303 [inline] ip6_output+0x356/0x620 net/ipv6/ip6_output.c:247 dst_output include/net/dst.h:450 [inline] NF_HOOK include/linux/netfilter.h:314 [inline] ip6_xmit+0x1ba6/0x25d0 net/ipv6/ip6_output.c:366 inet6_csk_xmit+0x442/0x530 net/ipv6/inet6_connection_sock.c:135 __tcp_transmit_skb+0x3b07/0x4880 net/ipv4/tcp_output.c:1466 tcp_transmit_skb net/ipv4/tcp_output.c:1484 [inline] tcp_connect+0x35b6/0x7130 net/ipv4/tcp_output.c:4143 tcp_v6_connect+0x1bcc/0x1e40 net/ipv6/tcp_ipv6.c:333 __inet_stream_connect+0x2ef/0x1730 net/ipv4/af_inet.c:679 inet_stream_connect+0x6a/0xd0 net/ipv4/af_inet.c:750 __sys_connect_file net/socket.c:2061 [inline] __sys_connect+0x606/0x690 net/socket.c:2078 __do_sys_connect net/socket.c:2088 [inline] __se_sys_connect net/socket.c:2085 [inline] __x64_sys_connect+0x91/0xe0 net/socket.c:2085 x64_sys_call+0x27a5/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:43 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was stored to memory at: nf_reject_ip6_tcphdr_put+0x60c/0x6c0 net/ipv6/netfilter/nf_reject_ipv6.c:249 nf_send_reset6+0xd84/0x15b0 net/ipv6/netfilter/nf_reject_ipv6.c:344 nft_reject_inet_eval+0x3c1/0x880 net/netfilter/nft_reject_inet.c:48 expr_call_ops_eval net/netfilter/nf_tables_core.c:240 [inline] nft_do_chain+0x438/0x22a0 net/netfilter/nf_tables_core.c:288 nft_do_chain_inet+0x41a/0x4f0 net/netfilter/nft_chain_filter.c:161 nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline] nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626 nf_hook include/linux/netfilter.h:269 [inline] NF_HOOK include/linux/netfilter.h:312 [inline] ipv6_rcv+0x29b/0x390 net/ipv6/ip6_input.c:310 __netif_receive_skb_one_core ---truncated---

In the Linux kernel, the following vulnerability has been resolved: mptcp: ensure snd_una is properly initialized on connect This is strictly related to commit fb7a0d334894 ("mptcp: ensure snd_nxt is properly initialized on connect"). It turns out that syzkaller can trigger the retransmit after fallback and before processing any other incoming packet - so that snd_una is still left uninitialized. Address the issue explicitly initializing snd_una together with snd_nxt and write_seq.

In the Linux kernel, the following vulnerability has been resolved: drm/nouveau: don't attempt to schedule hpd_work on headless cards If the card doesn't have display hardware, hpd_work and hpd_lock are left uninitialized which causes BUG when attempting to schedule hpd_work on runtime PM resume. Fix it by adding headless flag to DRM and skip any hpd if it's set.

In the Linux kernel, the following vulnerability has been resolved: ppp: fix ppp_async_encode() illegal access syzbot reported an issue in ppp_async_encode() [1] In this case, pppoe_sendmsg() is called with a zero size. Then ppp_async_encode() is called with an empty skb. BUG: KMSAN: uninit-value in ppp_async_encode drivers/net/ppp/ppp_async.c:545 [inline] BUG: KMSAN: uninit-value in ppp_async_push+0xb4f/0x2660 drivers/net/ppp/ppp_async.c:675 ppp_async_encode drivers/net/ppp/ppp_async.c:545 [inline] ppp_async_push+0xb4f/0x2660 drivers/net/ppp/ppp_async.c:675 ppp_async_send+0x130/0x1b0 drivers/net/ppp/ppp_async.c:634 ppp_channel_bridge_input drivers/net/ppp/ppp_generic.c:2280 [inline] ppp_input+0x1f1/0xe60 drivers/net/ppp/ppp_generic.c:2304 pppoe_rcv_core+0x1d3/0x720 drivers/net/ppp/pppoe.c:379 sk_backlog_rcv+0x13b/0x420 include/net/sock.h:1113 __release_sock+0x1da/0x330 net/core/sock.c:3072 release_sock+0x6b/0x250 net/core/sock.c:3626 pppoe_sendmsg+0x2b8/0xb90 drivers/net/ppp/pppoe.c:903 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:744 ____sys_sendmsg+0x903/0xb60 net/socket.c:2602 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2656 __sys_sendmmsg+0x3c1/0x960 net/socket.c:2742 __do_sys_sendmmsg net/socket.c:2771 [inline] __se_sys_sendmmsg net/socket.c:2768 [inline] __x64_sys_sendmmsg+0xbc/0x120 net/socket.c:2768 x64_sys_call+0xb6e/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:308 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Uninit was created at: slab_post_alloc_hook mm/slub.c:4092 [inline] slab_alloc_node mm/slub.c:4135 [inline] kmem_cache_alloc_node_noprof+0x6bf/0xb80 mm/slub.c:4187 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:587 __alloc_skb+0x363/0x7b0 net/core/skbuff.c:678 alloc_skb include/linux/skbuff.h:1322 [inline] sock_wmalloc+0xfe/0x1a0 net/core/sock.c:2732 pppoe_sendmsg+0x3a7/0xb90 drivers/net/ppp/pppoe.c:867 sock_sendmsg_nosec net/socket.c:729 [inline] __sock_sendmsg+0x30f/0x380 net/socket.c:744 ____sys_sendmsg+0x903/0xb60 net/socket.c:2602 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2656 __sys_sendmmsg+0x3c1/0x960 net/socket.c:2742 __do_sys_sendmmsg net/socket.c:2771 [inline] __se_sys_sendmmsg net/socket.c:2768 [inline] __x64_sys_sendmmsg+0xbc/0x120 net/socket.c:2768 x64_sys_call+0xb6e/0x3ba0 arch/x86/include/generated/asm/syscalls_64.h:308 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcd/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f CPU: 1 UID: 0 PID: 5411 Comm: syz.1.14 Not tainted 6.12.0-rc1-syzkaller-00165-g360c1f1f24c6 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024

In the Linux kernel, the following vulnerability has been resolved: netrom: check buffer length before accessing it Syzkaller reports an uninit value read from ax25cmp when sending raw message through ieee802154 implementation. ===================================================== BUG: KMSAN: uninit-value in ax25cmp+0x3a5/0x460 net/ax25/ax25_addr.c:119 ax25cmp+0x3a5/0x460 net/ax25/ax25_addr.c:119 nr_dev_get+0x20e/0x450 net/netrom/nr_route.c:601 nr_route_frame+0x1a2/0xfc0 net/netrom/nr_route.c:774 nr_xmit+0x5a/0x1c0 net/netrom/nr_dev.c:144 __netdev_start_xmit include/linux/netdevice.h:4940 [inline] netdev_start_xmit include/linux/netdevice.h:4954 [inline] xmit_one net/core/dev.c:3548 [inline] dev_hard_start_xmit+0x247/0xa10 net/core/dev.c:3564 __dev_queue_xmit+0x33b8/0x5130 net/core/dev.c:4349 dev_queue_xmit include/linux/netdevice.h:3134 [inline] raw_sendmsg+0x654/0xc10 net/ieee802154/socket.c:299 ieee802154_sock_sendmsg+0x91/0xc0 net/ieee802154/socket.c:96 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] ____sys_sendmsg+0x9c2/0xd60 net/socket.c:2584 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2638 __sys_sendmsg net/socket.c:2667 [inline] __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x307/0x490 net/socket.c:2674 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b Uninit was created at: slab_post_alloc_hook+0x129/0xa70 mm/slab.h:768 slab_alloc_node mm/slub.c:3478 [inline] kmem_cache_alloc_node+0x5e9/0xb10 mm/slub.c:3523 kmalloc_reserve+0x13d/0x4a0 net/core/skbuff.c:560 __alloc_skb+0x318/0x740 net/core/skbuff.c:651 alloc_skb include/linux/skbuff.h:1286 [inline] alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6334 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2780 sock_alloc_send_skb include/net/sock.h:1884 [inline] raw_sendmsg+0x36d/0xc10 net/ieee802154/socket.c:282 ieee802154_sock_sendmsg+0x91/0xc0 net/ieee802154/socket.c:96 sock_sendmsg_nosec net/socket.c:730 [inline] __sock_sendmsg net/socket.c:745 [inline] ____sys_sendmsg+0x9c2/0xd60 net/socket.c:2584 ___sys_sendmsg+0x28d/0x3c0 net/socket.c:2638 __sys_sendmsg net/socket.c:2667 [inline] __do_sys_sendmsg net/socket.c:2676 [inline] __se_sys_sendmsg net/socket.c:2674 [inline] __x64_sys_sendmsg+0x307/0x490 net/socket.c:2674 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0x44/0x110 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x63/0x6b CPU: 0 PID: 5037 Comm: syz-executor166 Not tainted 6.7.0-rc7-syzkaller-00003-gfbafc3e621c3 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023 ===================================================== This issue occurs because the skb buffer is too small, and it's actual allocation is aligned. This hides an actual issue, which is that nr_route_frame does not validate the buffer size before using it. Fix this issue by checking skb->len before accessing any fields in skb->data. Found by Linux Verification Center (linuxtesting.org) with Syzkaller.

In the Linux kernel, the following vulnerability has been resolved: iio: dummy: iio_simply_dummy_buffer: fix information leak in triggered buffer The 'data' array is allocated via kmalloc() and it is used to push data to user space from a triggered buffer, but it does not set values for inactive channels, as it only uses iio_for_each_active_channel() to assign new values. Use kzalloc for the memory allocation to avoid pushing uninitialized information to userspace.

In the Linux kernel, the following vulnerability has been resolved: net: bridge: xmit: make sure we have at least eth header len bytes syzbot triggered an uninit value[1] error in bridge device's xmit path by sending a short (less than ETH_HLEN bytes) skb. To fix it check if we can actually pull that amount instead of assuming. Tested with dropwatch: drop at: br_dev_xmit+0xb93/0x12d0 [bridge] (0xffffffffc06739b3) origin: software timestamp: Mon May 13 11:31:53 2024 778214037 nsec protocol: 0x88a8 length: 2 original length: 2 drop reason: PKT_TOO_SMALL [1] BUG: KMSAN: uninit-value in br_dev_xmit+0x61d/0x1cb0 net/bridge/br_device.c:65 br_dev_xmit+0x61d/0x1cb0 net/bridge/br_device.c:65 __netdev_start_xmit include/linux/netdevice.h:4903 [inline] netdev_start_xmit include/linux/netdevice.h:4917 [inline] xmit_one net/core/dev.c:3531 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3547 __dev_queue_xmit+0x34db/0x5350 net/core/dev.c:4341 dev_queue_xmit include/linux/netdevice.h:3091 [inline] __bpf_tx_skb net/core/filter.c:2136 [inline] __bpf_redirect_common net/core/filter.c:2180 [inline] __bpf_redirect+0x14a6/0x1620 net/core/filter.c:2187 ____bpf_clone_redirect net/core/filter.c:2460 [inline] bpf_clone_redirect+0x328/0x470 net/core/filter.c:2432 ___bpf_prog_run+0x13fe/0xe0f0 kernel/bpf/core.c:1997 __bpf_prog_run512+0xb5/0xe0 kernel/bpf/core.c:2238 bpf_dispatcher_nop_func include/linux/bpf.h:1234 [inline] __bpf_prog_run include/linux/filter.h:657 [inline] bpf_prog_run include/linux/filter.h:664 [inline] bpf_test_run+0x499/0xc30 net/bpf/test_run.c:425 bpf_prog_test_run_skb+0x14ea/0x1f20 net/bpf/test_run.c:1058 bpf_prog_test_run+0x6b7/0xad0 kernel/bpf/syscall.c:4269 __sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5678 __do_sys_bpf kernel/bpf/syscall.c:5767 [inline] __se_sys_bpf kernel/bpf/syscall.c:5765 [inline] __x64_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5765 x64_sys_call+0x96b/0x3b50 arch/x86/include/generated/asm/syscalls_64.h:322 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ti-ads8688: fix information leak in triggered buffer The 'buffer' local array is used to push data to user space from a triggered buffer, but it does not set values for inactive channels, as it only uses iio_for_each_active_channel() to assign new values. Initialize the array to zero before using it to avoid pushing uninitialized information to userspace.

In the Linux kernel, the following vulnerability has been resolved: iio: light: vcnl4035: fix information leak in triggered buffer The 'buffer' local array is used to push data to userspace from a triggered buffer, but it does not set an initial value for the single data element, which is an u16 aligned to 8 bytes. That leaves at least 4 bytes uninitialized even after writing an integer value with regmap_read(). Initialize the array to zero before using it to avoid pushing uninitialized information to userspace.

In the Linux kernel, the following vulnerability has been resolved: iio: pressure: zpa2326: fix information leak in triggered buffer The 'sample' local struct is used to push data to user space from a triggered buffer, but it has a hole between the temperature and the timestamp (u32 pressure, u16 temperature, GAP, u64 timestamp). This hole is never initialized. Initialize the struct to zero before using it to avoid pushing uninitialized information to userspace.

In the Linux kernel, the following vulnerability has been resolved: iio: imu: kmx61: fix information leak in triggered buffer The 'buffer' local array is used to push data to user space from a triggered buffer, but it does not set values for inactive channels, as it only uses iio_for_each_active_channel() to assign new values. Initialize the array to zero before using it to avoid pushing uninitialized information to userspace.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: rockchip_saradc: fix information leak in triggered buffer The 'data' local struct is used to push data to user space from a triggered buffer, but it does not set values for inactive channels, as it only uses iio_for_each_active_channel() to assign new values. Initialize the struct to zero before using it to avoid pushing uninitialized information to userspace.

In the Linux kernel, the following vulnerability has been resolved: iio: adc: ti-ads1119: fix information leak in triggered buffer The 'scan' local struct is used to push data to user space from a triggered buffer, but it has a hole between the sample (unsigned int) and the timestamp. This hole is never initialized. Initialize the struct to zero before using it to avoid pushing uninitialized information to userspace.

In the Linux kernel, the following vulnerability has been resolved: wifi: wcn36xx: fix channel survey memory allocation size KASAN reported a memory allocation issue in wcn->chan_survey due to incorrect size calculation. This commit uses kcalloc to allocate memory for wcn->chan_survey, ensuring proper initialization and preventing the use of uninitialized values when there are no frames on the channel.

In the Linux kernel, the following vulnerability has been resolved: iio: light: bh1745: fix information leak in triggered buffer The 'scan' local struct is used to push data to user space from a triggered buffer, but it does not set values for inactive channels, as it only uses iio_for_each_active_channel() to assign new values. Initialize the struct to zero before using it to avoid pushing uninitialized information to userspace.

In the Linux kernel, the following vulnerability has been resolved: ocfs2: free inode when ocfs2_get_init_inode() fails syzbot is reporting busy inodes after unmount, for commit 9c89fe0af826 ("ocfs2: Handle error from dquot_initialize()") forgot to call iput() when new_inode() succeeded and dquot_initialize() failed.

In the Linux kernel, the following vulnerability has been resolved: rtc: check if __rtc_read_time was successful in rtc_timer_do_work() If the __rtc_read_time call fails,, the struct rtc_time tm; may contain uninitialized data, or an illegal date/time read from the RTC hardware. When calling rtc_tm_to_ktime later, the result may be a very large value (possibly KTIME_MAX). If there are periodic timers in rtc->timerqueue, they will continually expire, may causing kernel softlockup.

In the Linux kernel, the following vulnerability has been resolved: media: dvb-frontends: dib3000mb: fix uninit-value in dib3000_write_reg Syzbot reports [1] an uninitialized value issue found by KMSAN in dib3000_read_reg(). Local u8 rb[2] is used in i2c_transfer() as a read buffer; in case that call fails, the buffer may end up with some undefined values. Since no elaborate error handling is expected in dib3000_write_reg(), simply zero out rb buffer to mitigate the problem. [1] Syzkaller report dvb-usb: bulk message failed: -22 (6/0) ===================================================== BUG: KMSAN: uninit-value in dib3000mb_attach+0x2d8/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758 dib3000mb_attach+0x2d8/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758 dibusb_dib3000mb_frontend_attach+0x155/0x2f0 drivers/media/usb/dvb-usb/dibusb-mb.c:31 dvb_usb_adapter_frontend_init+0xed/0x9a0 drivers/media/usb/dvb-usb/dvb-usb-dvb.c:290 dvb_usb_adapter_init drivers/media/usb/dvb-usb/dvb-usb-init.c:90 [inline] dvb_usb_init drivers/media/usb/dvb-usb/dvb-usb-init.c:186 [inline] dvb_usb_device_init+0x25a8/0x3760 drivers/media/usb/dvb-usb/dvb-usb-init.c:310 dibusb_probe+0x46/0x250 drivers/media/usb/dvb-usb/dibusb-mb.c:110 ... Local variable rb created at: dib3000_read_reg+0x86/0x4e0 drivers/media/dvb-frontends/dib3000mb.c:54 dib3000mb_attach+0x123/0x3c0 drivers/media/dvb-frontends/dib3000mb.c:758 ...

In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: Check num_codecs is not zero to avoid panic during probe Following commit 13f58267cda3 ("ASoC: soc.h: don't create dummy Component via COMP_DUMMY()"), COMP_DUMMY() became an array with zero length, and only gets populated with the dummy struct after the card is registered. Since the sound card driver's probe happens before the card registration, accessing any of the members of a dummy component during probe will result in undefined behavior. This can be observed in the mt8188 and mt8195 machine sound drivers. By omitting a dai link subnode in the sound card's node in the Devicetree, the default uninitialized dummy codec is used, and when its dai_name pointer gets passed to strcmp() it results in a null pointer dereference and a kernel panic. In addition to that, set_card_codec_info() in the generic helpers file, mtk-soundcard-driver.c, will populate a dai link with a dummy codec when a dai link node is present in DT but with no codec property. The result is that at probe time, a dummy codec can either be uninitialized with num_codecs = 0, or be an initialized dummy codec, with num_codecs = 1 and dai_name = "snd-soc-dummy-dai". In order to accommodate for both situations, check that num_codecs is not zero before accessing the codecs' fields but still check for the codec's dai name against "snd-soc-dummy-dai" as needed. While at it, also drop the check that dai_name is not null in the mt8192 driver, introduced in commit 4d4e1b6319e5 ("ASoC: mediatek: mt8192: Check existence of dai_name before dereferencing"), as it is actually redundant given the preceding num_codecs != 0 check.

In the Linux kernel, the following vulnerability has been resolved: powerpc/fadump: Move fadump_cma_init to setup_arch() after initmem_init() During early init CMA_MIN_ALIGNMENT_BYTES can be PAGE_SIZE, since pageblock_order is still zero and it gets initialized later during initmem_init() e.g. setup_arch() -> initmem_init() -> sparse_init() -> set_pageblock_order() One such use case where this causes issue is - early_setup() -> early_init_devtree() -> fadump_reserve_mem() -> fadump_cma_init() This causes CMA memory alignment check to be bypassed in cma_init_reserved_mem(). Then later cma_activate_area() can hit a VM_BUG_ON_PAGE(pfn & ((1 << order) - 1)) if the reserved memory area was not pageblock_order aligned. Fix it by moving the fadump_cma_init() after initmem_init(), where other such cma reservations also gets called. <stack trace> ============== page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x10010 flags: 0x13ffff800000000(node=1|zone=0|lastcpupid=0x7ffff) CMA raw: 013ffff800000000 5deadbeef0000100 5deadbeef0000122 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: VM_BUG_ON_PAGE(pfn & ((1 << order) - 1)) ------------[ cut here ]------------ kernel BUG at mm/page_alloc.c:778! Call Trace: __free_one_page+0x57c/0x7b0 (unreliable) free_pcppages_bulk+0x1a8/0x2c8 free_unref_page_commit+0x3d4/0x4e4 free_unref_page+0x458/0x6d0 init_cma_reserved_pageblock+0x114/0x198 cma_init_reserved_areas+0x270/0x3e0 do_one_initcall+0x80/0x2f8 kernel_init_freeable+0x33c/0x530 kernel_init+0x34/0x26c ret_from_kernel_user_thread+0x14/0x1c

In the Linux kernel, the following vulnerability has been resolved: fs: Fix uninitialized value issue in from_kuid and from_kgid ocfs2_setattr() uses attr->ia_mode, attr->ia_uid and attr->ia_gid in a trace point even though ATTR_MODE, ATTR_UID and ATTR_GID aren't set. Initialize all fields of newattrs to avoid uninitialized variables, by checking if ATTR_MODE, ATTR_UID, ATTR_GID are initialized, otherwise 0.

In the Linux kernel, the following vulnerability has been resolved: ipvlan: ensure network headers are in skb linear part syzbot found that ipvlan_process_v6_outbound() was assuming the IPv6 network header isis present in skb->head [1] Add the needed pskb_network_may_pull() calls for both IPv4 and IPv6 handlers. [1] BUG: KMSAN: uninit-value in __ipv6_addr_type+0xa2/0x490 net/ipv6/addrconf_core.c:47 __ipv6_addr_type+0xa2/0x490 net/ipv6/addrconf_core.c:47 ipv6_addr_type include/net/ipv6.h:555 [inline] ip6_route_output_flags_noref net/ipv6/route.c:2616 [inline] ip6_route_output_flags+0x51/0x720 net/ipv6/route.c:2651 ip6_route_output include/net/ip6_route.h:93 [inline] ipvlan_route_v6_outbound+0x24e/0x520 drivers/net/ipvlan/ipvlan_core.c:476 ipvlan_process_v6_outbound drivers/net/ipvlan/ipvlan_core.c:491 [inline] ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:541 [inline] ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:605 [inline] ipvlan_queue_xmit+0xd72/0x1780 drivers/net/ipvlan/ipvlan_core.c:671 ipvlan_start_xmit+0x5b/0x210 drivers/net/ipvlan/ipvlan_main.c:223 __netdev_start_xmit include/linux/netdevice.h:5150 [inline] netdev_start_xmit include/linux/netdevice.h:5159 [inline] xmit_one net/core/dev.c:3735 [inline] dev_hard_start_xmit+0x247/0xa20 net/core/dev.c:3751 sch_direct_xmit+0x399/0xd40 net/sched/sch_generic.c:343 qdisc_restart net/sched/sch_generic.c:408 [inline] __qdisc_run+0x14da/0x35d0 net/sched/sch_generic.c:416 qdisc_run+0x141/0x4d0 include/net/pkt_sched.h:127 net_tx_action+0x78b/0x940 net/core/dev.c:5484 handle_softirqs+0x1a0/0x7c0 kernel/softirq.c:561 __do_softirq+0x14/0x1a kernel/softirq.c:595 do_softirq+0x9a/0x100 kernel/softirq.c:462 __local_bh_enable_ip+0x9f/0xb0 kernel/softirq.c:389 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:919 [inline] __dev_queue_xmit+0x2758/0x57d0 net/core/dev.c:4611 dev_queue_xmit include/linux/netdevice.h:3311 [inline] packet_xmit+0x9c/0x6c0 net/packet/af_packet.c:276 packet_snd net/packet/af_packet.c:3132 [inline] packet_sendmsg+0x93e0/0xa7e0 net/packet/af_packet.c:3164 sock_sendmsg_nosec net/socket.c:718 [inline]

In the Linux kernel, the following vulnerability has been resolved: nfs: Fix KMSAN warning in decode_getfattr_attrs() Fix the following KMSAN warning: CPU: 1 UID: 0 PID: 7651 Comm: cp Tainted: G B Tainted: [B]=BAD_PAGE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009) ===================================================== ===================================================== BUG: KMSAN: uninit-value in decode_getfattr_attrs+0x2d6d/0x2f90 decode_getfattr_attrs+0x2d6d/0x2f90 decode_getfattr_generic+0x806/0xb00 nfs4_xdr_dec_getattr+0x1de/0x240 rpcauth_unwrap_resp_decode+0xab/0x100 rpcauth_unwrap_resp+0x95/0xc0 call_decode+0x4ff/0xb50 __rpc_execute+0x57b/0x19d0 rpc_execute+0x368/0x5e0 rpc_run_task+0xcfe/0xee0 nfs4_proc_getattr+0x5b5/0x990 __nfs_revalidate_inode+0x477/0xd00 nfs_access_get_cached+0x1021/0x1cc0 nfs_do_access+0x9f/0xae0 nfs_permission+0x1e4/0x8c0 inode_permission+0x356/0x6c0 link_path_walk+0x958/0x1330 path_lookupat+0xce/0x6b0 filename_lookup+0x23e/0x770 vfs_statx+0xe7/0x970 vfs_fstatat+0x1f2/0x2c0 __se_sys_newfstatat+0x67/0x880 __x64_sys_newfstatat+0xbd/0x120 x64_sys_call+0x1826/0x3cf0 do_syscall_64+0xd0/0x1b0 entry_SYSCALL_64_after_hwframe+0x77/0x7f The KMSAN warning is triggered in decode_getfattr_attrs(), when calling decode_attr_mdsthreshold(). It appears that fattr->mdsthreshold is not initialized. Fix the issue by initializing fattr->mdsthreshold to NULL in nfs_fattr_init().

In the Linux kernel, the following vulnerability has been resolved: ipvs: fix UB due to uninitialized stack access in ip_vs_protocol_init() Under certain kernel configurations when building with Clang/LLVM, the compiler does not generate a return or jump as the terminator instruction for ip_vs_protocol_init(), triggering the following objtool warning during build time: vmlinux.o: warning: objtool: ip_vs_protocol_init() falls through to next function __initstub__kmod_ip_vs_rr__935_123_ip_vs_rr_init6() At runtime, this either causes an oops when trying to load the ipvs module or a boot-time panic if ipvs is built-in. This same issue has been reported by the Intel kernel test robot previously. Digging deeper into both LLVM and the kernel code reveals this to be a undefined behavior problem. ip_vs_protocol_init() uses a on-stack buffer of 64 chars to store the registered protocol names and leaves it uninitialized after definition. The function calls strnlen() when concatenating protocol names into the buffer. With CONFIG_FORTIFY_SOURCE strnlen() performs an extra step to check whether the last byte of the input char buffer is a null character (commit 3009f891bb9f ("fortify: Allow strlen() and strnlen() to pass compile-time known lengths")). This, together with possibly other configurations, cause the following IR to be generated: define hidden i32 @ip_vs_protocol_init() local_unnamed_addr #5 section ".init.text" align 16 !kcfi_type !29 { %1 = alloca [64 x i8], align 16 ... 14: ; preds = %11 %15 = getelementptr inbounds i8, ptr %1, i64 63 %16 = load i8, ptr %15, align 1 %17 = tail call i1 @llvm.is.constant.i8(i8 %16) %18 = icmp eq i8 %16, 0 %19 = select i1 %17, i1 %18, i1 false br i1 %19, label %20, label %23 20: ; preds = %14 %21 = call i64 @strlen(ptr noundef nonnull dereferenceable(1) %1) #23 ... 23: ; preds = %14, %11, %20 %24 = call i64 @strnlen(ptr noundef nonnull dereferenceable(1) %1, i64 noundef 64) #24 ... } The above code calculates the address of the last char in the buffer (value %15) and then loads from it (value %16). Because the buffer is never initialized, the LLVM GVN pass marks value %16 as undefined: %13 = getelementptr inbounds i8, ptr %1, i64 63 br i1 undef, label %14, label %17 This gives later passes (SCCP, in particular) more DCE opportunities by propagating the undef value further, and eventually removes everything after the load on the uninitialized stack location: define hidden i32 @ip_vs_protocol_init() local_unnamed_addr #0 section ".init.text" align 16 !kcfi_type !11 { %1 = alloca [64 x i8], align 16 ... 12: ; preds = %11 %13 = getelementptr inbounds i8, ptr %1, i64 63 unreachable } In this way, the generated native code will just fall through to the next function, as LLVM does not generate any code for the unreachable IR instruction and leaves the function without a terminator. Zero the on-stack buffer to avoid this possible UB.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: qcom-pmic: init value of hdr_len/txbuf_len earlier If the read of USB_PDPHY_RX_ACKNOWLEDGE_REG failed, then hdr_len and txbuf_len are uninitialized. This commit stops to print uninitialized value and misleading/false data.

In the Linux kernel, the following vulnerability has been resolved: ext4: init quota for 'old.inode' in 'ext4_rename' Syzbot found the following issue: ext4_parse_param: s_want_extra_isize=128 ext4_inode_info_init: s_want_extra_isize=32 ext4_rename: old.inode=ffff88823869a2c8 old.dir=ffff888238699828 new.inode=ffff88823869d7e8 new.dir=ffff888238699828 __ext4_mark_inode_dirty: inode=ffff888238699828 ea_isize=32 want_ea_size=128 __ext4_mark_inode_dirty: inode=ffff88823869a2c8 ea_isize=32 want_ea_size=128 ext4_xattr_block_set: inode=ffff88823869a2c8 ------------[ cut here ]------------ WARNING: CPU: 13 PID: 2234 at fs/ext4/xattr.c:2070 ext4_xattr_block_set.cold+0x22/0x980 Modules linked in: RIP: 0010:ext4_xattr_block_set.cold+0x22/0x980 RSP: 0018:ffff888227d3f3b0 EFLAGS: 00010202 RAX: 0000000000000001 RBX: ffff88823007a000 RCX: 0000000000000000 RDX: 0000000000000a03 RSI: 0000000000000040 RDI: ffff888230078178 RBP: 0000000000000000 R08: 000000000000002c R09: ffffed1075c7df8e R10: ffff8883ae3efc6b R11: ffffed1075c7df8d R12: 0000000000000000 R13: ffff88823869a2c8 R14: ffff8881012e0460 R15: dffffc0000000000 FS: 00007f350ac1f740(0000) GS:ffff8883ae200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f350a6ed6a0 CR3: 0000000237456000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? ext4_xattr_set_entry+0x3b7/0x2320 ? ext4_xattr_block_set+0x0/0x2020 ? ext4_xattr_set_entry+0x0/0x2320 ? ext4_xattr_check_entries+0x77/0x310 ? ext4_xattr_ibody_set+0x23b/0x340 ext4_xattr_move_to_block+0x594/0x720 ext4_expand_extra_isize_ea+0x59a/0x10f0 __ext4_expand_extra_isize+0x278/0x3f0 __ext4_mark_inode_dirty.cold+0x347/0x410 ext4_rename+0xed3/0x174f vfs_rename+0x13a7/0x2510 do_renameat2+0x55d/0x920 __x64_sys_rename+0x7d/0xb0 do_syscall_64+0x3b/0xa0 entry_SYSCALL_64_after_hwframe+0x72/0xdc As 'ext4_rename' will modify 'old.inode' ctime and mark inode dirty, which may trigger expand 'extra_isize' and allocate block. If inode didn't init quota will lead to warning. To solve above issue, init 'old.inode' firstly in 'ext4_rename'.

In the Linux kernel, the following vulnerability has been resolved: btrfs: reinitialize delayed ref list after deleting it from the list At insert_delayed_ref() if we need to update the action of an existing ref to BTRFS_DROP_DELAYED_REF, we delete the ref from its ref head's ref_add_list using list_del(), which leaves the ref's add_list member not reinitialized, as list_del() sets the next and prev members of the list to LIST_POISON1 and LIST_POISON2, respectively. If later we end up calling drop_delayed_ref() against the ref, which can happen during merging or when destroying delayed refs due to a transaction abort, we can trigger a crash since at drop_delayed_ref() we call list_empty() against the ref's add_list, which returns false since the list was not reinitialized after the list_del() and as a consequence we call list_del() again at drop_delayed_ref(). This results in an invalid list access since the next and prev members are set to poison pointers, resulting in a splat if CONFIG_LIST_HARDENED and CONFIG_DEBUG_LIST are set or invalid poison pointer dereferences otherwise. So fix this by deleting from the list with list_del_init() instead.

In the Linux kernel, the following vulnerability has been resolved: drm/panthor: Fix access to uninitialized variable in tick_ctx_cleanup() The group variable can't be used to retrieve ptdev in our second loop, because it points to the previously iterated list_head, not a valid group. Get the ptdev object from the scheduler instead.

In the Linux kernel, the following vulnerability has been resolved: udf: fix uninit-value use in udf_get_fileshortad Check for overflow when computing alen in udf_current_aext to mitigate later uninit-value use in udf_get_fileshortad KMSAN bug[1]. After applying the patch reproducer did not trigger any issue[2]. [1] https://syzkaller.appspot.com/bug?extid=8901c4560b7ab5c2f9df [2] https://syzkaller.appspot.com/x/log.txt?x=10242227980000

In the Linux kernel, the following vulnerability has been resolved: iommu/mediatek: Fix crash on isr after kexec() If the system is rebooted via isr(), the IRQ handler might be triggered before the domain is initialized. Resulting on an invalid memory access error. Fix: [ 0.500930] Unable to handle kernel read from unreadable memory at virtual address 0000000000000070 [ 0.501166] Call trace: [ 0.501174] report_iommu_fault+0x28/0xfc [ 0.501180] mtk_iommu_isr+0x10c/0x1c0 [ joro: Fixed spelling in commit message ]

In the Linux kernel, the following vulnerability has been resolved: HID: core: zero-initialize the report buffer Since the report buffer is used by all kinds of drivers in various ways, let's zero-initialize it during allocation to make sure that it can't be ever used to leak kernel memory via specially-crafted report.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: Init completion before kobject_init_and_add() In cpufreq_policy_alloc(), it will call uninitialed completion in cpufreq_sysfs_release() when kobject_init_and_add() fails. And that will cause a crash such as the following page fault in complete: BUG: unable to handle page fault for address: fffffffffffffff8 [..] RIP: 0010:complete+0x98/0x1f0 [..] Call Trace: kobject_put+0x1be/0x4c0 cpufreq_online.cold+0xee/0x1fd cpufreq_add_dev+0x183/0x1e0 subsys_interface_register+0x3f5/0x4e0 cpufreq_register_driver+0x3b7/0x670 acpi_cpufreq_init+0x56c/0x1000 [acpi_cpufreq] do_one_initcall+0x13d/0x780 do_init_module+0x1c3/0x630 load_module+0x6e67/0x73b0 __do_sys_finit_module+0x181/0x240 do_syscall_64+0x35/0x80 entry_SYSCALL_64_after_hwframe+0x63/0xcd

In the Linux kernel, the following vulnerability has been resolved: NFSD: Initialize struct nfsd4_copy earlier Ensure the refcount and async_copies fields are initialized early. cleanup_async_copy() will reference these fields if an error occurs in nfsd4_copy(). If they are not correctly initialized, at the very least, a refcount underflow occurs.

In the Linux kernel, the following vulnerability has been resolved: iommu/vt-d: Clean up si_domain in the init_dmars() error path A splat from kmem_cache_destroy() was seen with a kernel prior to commit ee2653bbe89d ("iommu/vt-d: Remove domain and devinfo mempool") when there was a failure in init_dmars(), because the iommu_domain cache still had objects. While the mempool code is now gone, there still is a leak of the si_domain memory if init_dmars() fails. So clean up si_domain in the init_dmars() error path.

In the Linux kernel, the following vulnerability has been resolved: 9p: set req refcount to zero to avoid uninitialized usage When a new request is allocated, the refcount will be zero if it is reused, but if the request is newly allocated from slab, it is not fully initialized before being added to idr. If the p9_read_work got a response before the refcount initiated. It will use a uninitialized req, which will result in a bad request data struct. Here is the logs from syzbot. Corrupted memory at 0xffff88807eade00b [ 0xff 0x07 0x00 0x00 0x00 0x00 0x00 0x00 . . . . . . . . ] (in kfence-#110): p9_fcall_fini net/9p/client.c:248 [inline] p9_req_put net/9p/client.c:396 [inline] p9_req_put+0x208/0x250 net/9p/client.c:390 p9_client_walk+0x247/0x540 net/9p/client.c:1165 clone_fid fs/9p/fid.h:21 [inline] v9fs_fid_xattr_set+0xe4/0x2b0 fs/9p/xattr.c:118 v9fs_xattr_set fs/9p/xattr.c:100 [inline] v9fs_xattr_handler_set+0x6f/0x120 fs/9p/xattr.c:159 __vfs_setxattr+0x119/0x180 fs/xattr.c:182 __vfs_setxattr_noperm+0x129/0x5f0 fs/xattr.c:216 __vfs_setxattr_locked+0x1d3/0x260 fs/xattr.c:277 vfs_setxattr+0x143/0x340 fs/xattr.c:309 setxattr+0x146/0x160 fs/xattr.c:617 path_setxattr+0x197/0x1c0 fs/xattr.c:636 __do_sys_setxattr fs/xattr.c:652 [inline] __se_sys_setxattr fs/xattr.c:648 [inline] __ia32_sys_setxattr+0xc0/0x160 fs/xattr.c:648 do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline] __do_fast_syscall_32+0x65/0xf0 arch/x86/entry/common.c:178 do_fast_syscall_32+0x33/0x70 arch/x86/entry/common.c:203 entry_SYSENTER_compat_after_hwframe+0x70/0x82 Below is a similar scenario, the scenario in the syzbot log looks more complicated than this one, but this patch can fix it. T21124 p9_read_work ======================== second trans ================================= p9_client_walk p9_client_rpc p9_client_prepare_req p9_tag_alloc req = kmem_cache_alloc(p9_req_cache, GFP_NOFS); tag = idr_alloc << preempted >> req->tc.tag = tag; /* req->[refcount/tag] == uninitialized */ m->rreq = p9_tag_lookup(m->client, m->rc.tag); /* increments uninitalized refcount */ refcount_set(&req->refcount, 2); /* cb drops one ref */ p9_client_cb(req) /* reader thread drops its ref: request is incorrectly freed */ p9_req_put(req) /* use after free and ref underflow */ p9_req_put(req) To fix it, we can initialize the refcount to zero before add to idr.

In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: do not pass a stopped vif to the driver in .get_txpower Avoid potentially crashing in the driver because of uninitialized private data

In the Linux kernel, the following vulnerability has been resolved: sctp: properly validate chunk size in sctp_sf_ootb() A size validation fix similar to that in Commit 50619dbf8db7 ("sctp: add size validation when walking chunks") is also required in sctp_sf_ootb() to address a crash reported by syzbot: BUG: KMSAN: uninit-value in sctp_sf_ootb+0x7f5/0xce0 net/sctp/sm_statefuns.c:3712 sctp_sf_ootb+0x7f5/0xce0 net/sctp/sm_statefuns.c:3712 sctp_do_sm+0x181/0x93d0 net/sctp/sm_sideeffect.c:1166 sctp_endpoint_bh_rcv+0xc38/0xf90 net/sctp/endpointola.c:407 sctp_inq_push+0x2ef/0x380 net/sctp/inqueue.c:88 sctp_rcv+0x3831/0x3b20 net/sctp/input.c:243 sctp4_rcv+0x42/0x50 net/sctp/protocol.c:1159 ip_protocol_deliver_rcu+0xb51/0x13d0 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x336/0x500 net/ipv4/ip_input.c:233

In the Linux kernel, the following vulnerability has been resolved: regulator: rtq2208: Fix uninitialized use of regulator_config Fix rtq2208 driver uninitialized use to cause kernel error.