In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Load DR6 with guest value only before entering .vcpu_run() loop Move the conditional loading of hardware DR6 with the guest's DR6 value out of the core .vcpu_run() loop to fix a bug where KVM can load hardware with a stale vcpu->arch.dr6. When the guest accesses a DR and host userspace isn't debugging the guest, KVM disables DR interception and loads the guest's values into hardware on VM-Enter and saves them on VM-Exit. This allows the guest to access DRs at will, e.g. so that a sequence of DR accesses to configure a breakpoint only generates one VM-Exit. For DR0-DR3, the logic/behavior is identical between VMX and SVM, and also identical between KVM_DEBUGREG_BP_ENABLED (userspace debugging the guest) and KVM_DEBUGREG_WONT_EXIT (guest using DRs), and so KVM handles loading DR0-DR3 in common code, _outside_ of the core kvm_x86_ops.vcpu_run() loop. But for DR6, the guest's value doesn't need to be loaded into hardware for KVM_DEBUGREG_BP_ENABLED, and SVM provides a dedicated VMCB field whereas VMX requires software to manually load the guest value, and so loading the guest's value into DR6 is handled by {svm,vmx}_vcpu_run(), i.e. is done _inside_ the core run loop. Unfortunately, saving the guest values on VM-Exit is initiated by common x86, again outside of the core run loop. If the guest modifies DR6 (in hardware, when DR interception is disabled), and then the next VM-Exit is a fastpath VM-Exit, KVM will reload hardware DR6 with vcpu->arch.dr6 and clobber the guest's actual value. The bug shows up primarily with nested VMX because KVM handles the VMX preemption timer in the fastpath, and the window between hardware DR6 being modified (in guest context) and DR6 being read by guest software is orders of magnitude larger in a nested setup. E.g. in non-nested, the VMX preemption timer would need to fire precisely between #DB injection and the #DB handler's read of DR6, whereas with a KVM-on-KVM setup, the window where hardware DR6 is "dirty" extends all the way from L1 writing DR6 to VMRESUME (in L1). L1's view: ========== <L1 disables DR interception> CPU 0/KVM-7289 [023] d.... 2925.640961: kvm_entry: vcpu 0 A: L1 Writes DR6 CPU 0/KVM-7289 [023] d.... 2925.640963: <hack>: Set DRs, DR6 = 0xffff0ff1 B: CPU 0/KVM-7289 [023] d.... 2925.640967: kvm_exit: vcpu 0 reason EXTERNAL_INTERRUPT intr_info 0x800000ec D: L1 reads DR6, arch.dr6 = 0 CPU 0/KVM-7289 [023] d.... 2925.640969: <hack>: Sync DRs, DR6 = 0xffff0ff0 CPU 0/KVM-7289 [023] d.... 2925.640976: kvm_entry: vcpu 0 L2 reads DR6, L1 disables DR interception CPU 0/KVM-7289 [023] d.... 2925.640980: kvm_exit: vcpu 0 reason DR_ACCESS info1 0x0000000000000216 CPU 0/KVM-7289 [023] d.... 2925.640983: kvm_entry: vcpu 0 CPU 0/KVM-7289 [023] d.... 2925.640983: <hack>: Set DRs, DR6 = 0xffff0ff0 L2 detects failure CPU 0/KVM-7289 [023] d.... 2925.640987: kvm_exit: vcpu 0 reason HLT L1 reads DR6 (confirms failure) CPU 0/KVM-7289 [023] d.... 2925.640990: <hack>: Sync DRs, DR6 = 0xffff0ff0 L0's view: ========== L2 reads DR6, arch.dr6 = 0 CPU 23/KVM-5046 [001] d.... 3410.005610: kvm_exit: vcpu 23 reason DR_ACCESS info1 0x0000000000000216 CPU 23/KVM-5046 [001] ..... 3410.005610: kvm_nested_vmexit: vcpu 23 reason DR_ACCESS info1 0x0000000000000216 L2 => L1 nested VM-Exit CPU 23/KVM-5046 [001] ..... 3410.005610: kvm_nested_vmexit_inject: reason: DR_ACCESS ext_inf1: 0x0000000000000216 CPU 23/KVM-5046 [001] d.... 3410.005610: kvm_entry: vcpu 23 CPU 23/KVM-5046 [001] d.... 3410.005611: kvm_exit: vcpu 23 reason VMREAD CPU 23/KVM-5046 [001] d.... 3410.005611: kvm_entry: vcpu 23 CPU 23/KVM-5046 [001] d.... 3410. ---truncated---

In the Linux kernel, the following vulnerability has been resolved: platform/x86/amd/pmc: Only disable IRQ1 wakeup where i8042 actually enabled it Wakeup for IRQ1 should be disabled only in cases where i8042 had actually enabled it, otherwise "wake_depth" for this IRQ will try to drop below zero and there will be an unpleasant WARN() logged: kernel: atkbd serio0: Disabling IRQ1 wakeup source to avoid platform firmware bug kernel: ------------[ cut here ]------------ kernel: Unbalanced IRQ 1 wake disable kernel: WARNING: CPU: 10 PID: 6431 at kernel/irq/manage.c:920 irq_set_irq_wake+0x147/0x1a0 The PMC driver uses DEFINE_SIMPLE_DEV_PM_OPS() to define its dev_pm_ops which sets amd_pmc_suspend_handler() to the .suspend, .freeze, and .poweroff handlers. i8042_pm_suspend(), however, is only set as the .suspend handler. Fix the issue by call PMC suspend handler only from the same set of dev_pm_ops handlers as i8042_pm_suspend(), which currently means just the .suspend handler. To reproduce this issue try hibernating (S4) the machine after a fresh boot without putting it into s2idle first. [ij: edited the commit message.]

In the Linux kernel, the following vulnerability has been resolved: netfs: Fix kernel async DIO Netfslib needs to be able to handle kernel-initiated asynchronous DIO that is supplied with a bio_vec[] array. Currently, because of the async flag, this gets passed to netfs_extract_user_iter() which throws a warning and fails because it only handles IOVEC and UBUF iterators. This can be triggered through a combination of cifs and a loopback blockdev with something like: mount //my/cifs/share /foo dd if=/dev/zero of=/foo/m0 bs=4K count=1K losetup --sector-size 4096 --direct-io=on /dev/loop2046 /foo/m0 echo hello >/dev/loop2046 This causes the following to appear in syslog: WARNING: CPU: 2 PID: 109 at fs/netfs/iterator.c:50 netfs_extract_user_iter+0x170/0x250 [netfs] and the write to fail. Fix this by removing the check in netfs_unbuffered_write_iter_locked() that causes async kernel DIO writes to be handled as userspace writes. Note that this change relies on the kernel caller maintaining the existence of the bio_vec array (or kvec[] or folio_queue) until the op is complete.

In the Linux kernel, the following vulnerability has been resolved: gfs2: Truncate address space when flipping GFS2_DIF_JDATA flag Truncate an inode's address space when flipping the GFS2_DIF_JDATA flag: depending on that flag, the pages in the address space will either use buffer heads or iomap_folio_state structs, and we cannot mix the two.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rtrs: Add missing deinit() call A warning is triggered when repeatedly connecting and disconnecting the rnbd: list_add corruption. prev->next should be next (ffff88800b13e480), but was ffff88801ecd1338. (prev=ffff88801ecd1340). WARNING: CPU: 1 PID: 36562 at lib/list_debug.c:32 __list_add_valid_or_report+0x7f/0xa0 Workqueue: ib_cm cm_work_handler [ib_cm] RIP: 0010:__list_add_valid_or_report+0x7f/0xa0 ? __list_add_valid_or_report+0x7f/0xa0 ib_register_event_handler+0x65/0x93 [ib_core] rtrs_srv_ib_dev_init+0x29/0x30 [rtrs_server] rtrs_ib_dev_find_or_add+0x124/0x1d0 [rtrs_core] __alloc_path+0x46c/0x680 [rtrs_server] ? rtrs_rdma_connect+0xa6/0x2d0 [rtrs_server] ? rcu_is_watching+0xd/0x40 ? __mutex_lock+0x312/0xcf0 ? get_or_create_srv+0xad/0x310 [rtrs_server] ? rtrs_rdma_connect+0xa6/0x2d0 [rtrs_server] rtrs_rdma_connect+0x23c/0x2d0 [rtrs_server] ? __lock_release+0x1b1/0x2d0 cma_cm_event_handler+0x4a/0x1a0 [rdma_cm] cma_ib_req_handler+0x3a0/0x7e0 [rdma_cm] cm_process_work+0x28/0x1a0 [ib_cm] ? _raw_spin_unlock_irq+0x2f/0x50 cm_req_handler+0x618/0xa60 [ib_cm] cm_work_handler+0x71/0x520 [ib_cm] Commit 667db86bcbe8 ("RDMA/rtrs: Register ib event handler") introduced a new element .deinit but never used it at all. Fix it by invoking the `deinit()` to appropriately unregister the IB event handler.

In the Linux kernel, the following vulnerability has been resolved: md/md-bitmap: Synchronize bitmap_get_stats() with bitmap lifetime After commit ec6bb299c7c3 ("md/md-bitmap: add 'sync_size' into struct md_bitmap_stats"), following panic is reported: Oops: general protection fault, probably for non-canonical address RIP: 0010:bitmap_get_stats+0x2b/0xa0 Call Trace: <TASK> md_seq_show+0x2d2/0x5b0 seq_read_iter+0x2b9/0x470 seq_read+0x12f/0x180 proc_reg_read+0x57/0xb0 vfs_read+0xf6/0x380 ksys_read+0x6c/0xf0 do_syscall_64+0x82/0x170 entry_SYSCALL_64_after_hwframe+0x76/0x7e Root cause is that bitmap_get_stats() can be called at anytime if mddev is still there, even if bitmap is destroyed, or not fully initialized. Deferenceing bitmap in this case can crash the kernel. Meanwhile, the above commit start to deferencing bitmap->storage, make the problem easier to trigger. Fix the problem by protecting bitmap_get_stats() with bitmap_info.mutex.

A flaw was found in vringh_kiov_advance in drivers/vhost/vringh.c in the host side of a virtio ring in the Linux Kernel. This issue may result in a denial of service from guest to host via zero length descriptor.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: fix panic during interface removal Reference counting is used to ensure that batadv_hardif_neigh_node and batadv_hard_iface are not freed before/during batadv_v_elp_throughput_metric_update work is finished. But there isn't a guarantee that the hard if will remain associated with a soft interface up until the work is finished. This fixes a crash triggered by reboot that looks like this: Call trace: batadv_v_mesh_free+0xd0/0x4dc [batman_adv] batadv_v_elp_throughput_metric_update+0x1c/0xa4 process_one_work+0x178/0x398 worker_thread+0x2e8/0x4d0 kthread+0xd8/0xdc ret_from_fork+0x10/0x20 (the batadv_v_mesh_free call is misleading, and does not actually happen) I was able to make the issue happen more reliably by changing hardif_neigh->bat_v.metric_work work to be delayed work. This allowed me to track down and confirm the fix. [sven@narfation.org: prevent entering batadv_v_elp_get_throughput without soft_iface]

In the Linux kernel, the following vulnerability has been resolved: uprobes/x86: Harden uretprobe syscall trampoline check Jann reported a possible issue when trampoline_check_ip returns address near the bottom of the address space that is allowed to call into the syscall if uretprobes are not set up: https://lore.kernel.org/bpf/202502081235.5A6F352985@keescook/T/#m9d416df341b8fbc11737dacbcd29f0054413cbbf Though the mmap minimum address restrictions will typically prevent creating mappings there, let's make sure uretprobe syscall checks for that.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix r_count dec/increment mismatch r_count is only increased when there is an oplock break wait, so r_count inc/decrement are not paired. This can cause r_count to become negative, which can lead to a problem where the ksmbd thread does not terminate.

In the Linux kernel, the following vulnerability has been resolved: net: Remove RTNL dance for SIOCBRADDIF and SIOCBRDELIF. SIOCBRDELIF is passed to dev_ioctl() first and later forwarded to br_ioctl_call(), which causes unnecessary RTNL dance and the splat below [0] under RTNL pressure. Let's say Thread A is trying to detach a device from a bridge and Thread B is trying to remove the bridge. In dev_ioctl(), Thread A bumps the bridge device's refcnt by netdev_hold() and releases RTNL because the following br_ioctl_call() also re-acquires RTNL. In the race window, Thread B could acquire RTNL and try to remove the bridge device. Then, rtnl_unlock() by Thread B will release RTNL and wait for netdev_put() by Thread A. Thread A, however, must hold RTNL after the unlock in dev_ifsioc(), which may take long under RTNL pressure, resulting in the splat by Thread B. Thread A (SIOCBRDELIF) Thread B (SIOCBRDELBR) ---------------------- ---------------------- sock_ioctl sock_ioctl `- sock_do_ioctl `- br_ioctl_call `- dev_ioctl `- br_ioctl_stub |- rtnl_lock | |- dev_ifsioc ' ' |- dev = __dev_get_by_name(...) |- netdev_hold(dev, ...) . / |- rtnl_unlock ------. | | |- br_ioctl_call `---> |- rtnl_lock Race | | `- br_ioctl_stub |- br_del_bridge Window | | | |- dev = __dev_get_by_name(...) | | | May take long | `- br_dev_delete(dev, ...) | | | under RTNL pressure | `- unregister_netdevice_queue(dev, ...) | | | | `- rtnl_unlock \ | |- rtnl_lock <-' `- netdev_run_todo | |- ... `- netdev_run_todo | `- rtnl_unlock |- __rtnl_unlock | |- netdev_wait_allrefs_any |- netdev_put(dev, ...) <----------------' Wait refcnt decrement and log splat below To avoid blocking SIOCBRDELBR unnecessarily, let's not call dev_ioctl() for SIOCBRADDIF and SIOCBRDELIF. In the dev_ioctl() path, we do the following: 1. Copy struct ifreq by get_user_ifreq in sock_do_ioctl() 2. Check CAP_NET_ADMIN in dev_ioctl() 3. Call dev_load() in dev_ioctl() 4. Fetch the master dev from ifr.ifr_name in dev_ifsioc() 3. can be done by request_module() in br_ioctl_call(), so we move 1., 2., and 4. to br_ioctl_stub(). Note that 2. is also checked later in add_del_if(), but it's better performed before RTNL. SIOCBRADDIF and SIOCBRDELIF have been processed in dev_ioctl() since the pre-git era, and there seems to be no specific reason to process them there. [0]: unregister_netdevice: waiting for wpan3 to become free. Usage count = 2 ref_tracker: wpan3@ffff8880662d8608 has 1/1 users at __netdev_tracker_alloc include/linux/netdevice.h:4282 [inline] netdev_hold include/linux/netdevice.h:4311 [inline] dev_ifsioc+0xc6a/0x1160 net/core/dev_ioctl.c:624 dev_ioctl+0x255/0x10c0 net/core/dev_ioctl.c:826 sock_do_ioctl+0x1ca/0x260 net/socket.c:1213 sock_ioctl+0x23a/0x6c0 net/socket.c:1318 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl fs/ioctl.c:892 [inline] __x64_sys_ioctl+0x1a4/0x210 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xcb/0x250 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f

In the Linux kernel, the following vulnerability has been resolved: cifs: Fix integer overflow while processing closetimeo mount option User-provided mount parameter closetimeo of type u32 is intended to have an upper limit, but before it is validated, the value is converted from seconds to jiffies which can lead to an integer overflow. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: drm: zynqmp_dp: Fix a deadlock in zynqmp_dp_ignore_hpd_set() Instead of attempting the same mutex twice, lock and unlock it. This bug has been detected by the Clang thread-safety analyzer.

In the Linux kernel, the following vulnerability has been resolved: fbdev: hyperv_fb: Fix hang in kdump kernel when on Hyper-V Gen 2 VMs Gen 2 Hyper-V VMs boot via EFI and have a standard EFI framebuffer device. When the kdump kernel runs in such a VM, loading the efifb driver may hang because of accessing the framebuffer at the wrong memory address. The scenario occurs when the hyperv_fb driver in the original kernel moves the framebuffer to a different MMIO address because of conflicts with an already-running efifb or simplefb driver. The hyperv_fb driver then informs Hyper-V of the change, which is allowed by the Hyper-V FB VMBus device protocol. However, when the kexec command loads the kdump kernel into crash memory via the kexec_file_load() system call, the system call doesn't know the framebuffer has moved, and it sets up the kdump screen_info using the original framebuffer address. The transition to the kdump kernel does not go through the Hyper-V host, so Hyper-V does not reset the framebuffer address like it would do on a reboot. When efifb tries to run, it accesses a non-existent framebuffer address, which traps to the Hyper-V host. After many such accesses, the Hyper-V host thinks the guest is being malicious, and throttles the guest to the point that it runs very slowly or appears to have hung. When the kdump kernel is loaded into crash memory via the kexec_load() system call, the problem does not occur. In this case, the kexec command builds the screen_info table itself in user space from data returned by the FBIOGET_FSCREENINFO ioctl against /dev/fb0, which gives it the new framebuffer location. This problem was originally reported in 2020 [1], resulting in commit 3cb73bc3fa2a ("hyperv_fb: Update screen_info after removing old framebuffer"). This commit solved the problem by setting orig_video_isVGA to 0, so the kdump kernel was unaware of the EFI framebuffer. The efifb driver did not try to load, and no hang occurred. But in 2024, commit c25a19afb81c ("fbdev/hyperv_fb: Do not clear global screen_info") effectively reverted 3cb73bc3fa2a. Commit c25a19afb81c has no reference to 3cb73bc3fa2a, so perhaps it was done without knowing the implications that were reported with 3cb73bc3fa2a. In any case, as of commit c25a19afb81c, the original problem came back again. Interestingly, the hyperv_drm driver does not have this problem because it never moves the framebuffer. The difference is that the hyperv_drm driver removes any conflicting framebuffers *before* allocating an MMIO address, while the hyperv_fb drivers removes conflicting framebuffers *after* allocating an MMIO address. With the "after" ordering, hyperv_fb may encounter a conflict and move the framebuffer to a different MMIO address. But the conflict is essentially bogus because it is removed a few lines of code later. Rather than fix the problem with the approach from 2020 in commit 3cb73bc3fa2a, instead slightly reorder the steps in hyperv_fb so conflicting framebuffers are removed before allocating an MMIO address. Then the default framebuffer MMIO address should always be available, and there's never any confusion about which framebuffer address the kdump kernel should use -- it's always the original address provided by the Hyper-V host. This approach is already used by the hyperv_drm driver, and is consistent with the usage guidelines at the head of the module with the function aperture_remove_conflicting_devices(). This approach also solves a related minor problem when kexec_load() is used to load the kdump kernel. With current code, unbinding and rebinding the hyperv_fb driver could result in the framebuffer moving back to the default framebuffer address, because on the rebind there are no conflicts. If such a move is done after the kdump kernel is loaded with the new framebuffer address, at kdump time it could again have the wrong address. This problem and fix are described in terms of the kdump kernel, but it can also occur ---truncated---

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix assertion failure when splitting ordered extent after transaction abort If while we are doing a direct IO write a transaction abort happens, we mark all existing ordered extents with the BTRFS_ORDERED_IOERR flag (done at btrfs_destroy_ordered_extents()), and then after that if we enter btrfs_split_ordered_extent() and the ordered extent has bytes left (meaning we have a bio that doesn't cover the whole ordered extent, see details at btrfs_extract_ordered_extent()), we will fail on the following assertion at btrfs_split_ordered_extent(): ASSERT(!(flags & ~BTRFS_ORDERED_TYPE_FLAGS)); because the BTRFS_ORDERED_IOERR flag is set and the definition of BTRFS_ORDERED_TYPE_FLAGS is just the union of all flags that identify the type of write (regular, nocow, prealloc, compressed, direct IO, encoded). Fix this by returning an error from btrfs_extract_ordered_extent() if we find the BTRFS_ORDERED_IOERR flag in the ordered extent. The error will be the error that resulted in the transaction abort or -EIO if no transaction abort happened. This was recently reported by syzbot with the following trace: FAULT_INJECTION: forcing a failure. name failslab, interval 1, probability 0, space 0, times 1 CPU: 0 UID: 0 PID: 5321 Comm: syz.0.0 Not tainted 6.13.0-rc5-syzkaller #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 fail_dump lib/fault-inject.c:53 [inline] should_fail_ex+0x3b0/0x4e0 lib/fault-inject.c:154 should_failslab+0xac/0x100 mm/failslab.c:46 slab_pre_alloc_hook mm/slub.c:4072 [inline] slab_alloc_node mm/slub.c:4148 [inline] __do_kmalloc_node mm/slub.c:4297 [inline] __kmalloc_noprof+0xdd/0x4c0 mm/slub.c:4310 kmalloc_noprof include/linux/slab.h:905 [inline] kzalloc_noprof include/linux/slab.h:1037 [inline] btrfs_chunk_alloc_add_chunk_item+0x244/0x1100 fs/btrfs/volumes.c:5742 reserve_chunk_space+0x1ca/0x2c0 fs/btrfs/block-group.c:4292 check_system_chunk fs/btrfs/block-group.c:4319 [inline] do_chunk_alloc fs/btrfs/block-group.c:3891 [inline] btrfs_chunk_alloc+0x77b/0xf80 fs/btrfs/block-group.c:4187 find_free_extent_update_loop fs/btrfs/extent-tree.c:4166 [inline] find_free_extent+0x42d1/0x5810 fs/btrfs/extent-tree.c:4579 btrfs_reserve_extent+0x422/0x810 fs/btrfs/extent-tree.c:4672 btrfs_new_extent_direct fs/btrfs/direct-io.c:186 [inline] btrfs_get_blocks_direct_write+0x706/0xfa0 fs/btrfs/direct-io.c:321 btrfs_dio_iomap_begin+0xbb7/0x1180 fs/btrfs/direct-io.c:525 iomap_iter+0x697/0xf60 fs/iomap/iter.c:90 __iomap_dio_rw+0xeb9/0x25b0 fs/iomap/direct-io.c:702 btrfs_dio_write fs/btrfs/direct-io.c:775 [inline] btrfs_direct_write+0x610/0xa30 fs/btrfs/direct-io.c:880 btrfs_do_write_iter+0x2a0/0x760 fs/btrfs/file.c:1397 do_iter_readv_writev+0x600/0x880 vfs_writev+0x376/0xba0 fs/read_write.c:1050 do_pwritev fs/read_write.c:1146 [inline] __do_sys_pwritev2 fs/read_write.c:1204 [inline] __se_sys_pwritev2+0x196/0x2b0 fs/read_write.c:1195 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f1281f85d29 RSP: 002b:00007f12819fe038 EFLAGS: 00000246 ORIG_RAX: 0000000000000148 RAX: ffffffffffffffda RBX: 00007f1282176080 RCX: 00007f1281f85d29 RDX: 0000000000000001 RSI: 0000000020000240 RDI: 0000000000000005 RBP: 00007f12819fe090 R08: 0000000000000000 R09: 0000000000000003 R10: 0000000000007000 R11: 0000000000000246 R12: 0000000000000002 R13: 0000000000000000 R14: 00007f1282176080 R15: 00007ffcb9e23328 </TASK> BTRFS error (device loop0 state A): Transaction aborted (error -12) BTRFS: error (device loop0 state A ---truncated---

In the Linux kernel, the following vulnerability has been resolved: nvmet: Fix crash when a namespace is disabled The namespace percpu counter protects pending I/O, and we can only safely diable the namespace once the counter drop to zero. Otherwise we end up with a crash when running blktests/nvme/058 (eg for loop transport): [ 2352.930426] [ T53909] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000005: 0000 [#1] PREEMPT SMP KASAN PTI [ 2352.930431] [ T53909] KASAN: null-ptr-deref in range [0x0000000000000028-0x000000000000002f] [ 2352.930434] [ T53909] CPU: 3 UID: 0 PID: 53909 Comm: kworker/u16:5 Tainted: G W 6.13.0-rc6 #232 [ 2352.930438] [ T53909] Tainted: [W]=WARN [ 2352.930440] [ T53909] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 [ 2352.930443] [ T53909] Workqueue: nvmet-wq nvme_loop_execute_work [nvme_loop] [ 2352.930449] [ T53909] RIP: 0010:blkcg_set_ioprio+0x44/0x180 as the queue is already torn down when calling submit_bio(); So we need to init the percpu counter in nvmet_ns_enable(), and wait for it to drop to zero in nvmet_ns_disable() to avoid having I/O pending after the namespace has been disabled.

In the Linux kernel, the following vulnerability has been resolved: gpio: xilinx: Convert gpio_lock to raw spinlock irq_chip functions may be called in raw spinlock context. Therefore, we must also use a raw spinlock for our own internal locking. This fixes the following lockdep splat: [ 5.349336] ============================= [ 5.353349] [ BUG: Invalid wait context ] [ 5.357361] 6.13.0-rc5+ #69 Tainted: G W [ 5.363031] ----------------------------- [ 5.367045] kworker/u17:1/44 is trying to lock: [ 5.371587] ffffff88018b02c0 (&chip->gpio_lock){....}-{3:3}, at: xgpio_irq_unmask (drivers/gpio/gpio-xilinx.c:433 (discriminator 8)) [ 5.380079] other info that might help us debug this: [ 5.385138] context-{5:5} [ 5.387762] 5 locks held by kworker/u17:1/44: [ 5.392123] #0: ffffff8800014958 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work (kernel/workqueue.c:3204) [ 5.402260] #1: ffffffc082fcbdd8 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work (kernel/workqueue.c:3205) [ 5.411528] #2: ffffff880172c900 (&dev->mutex){....}-{4:4}, at: __device_attach (drivers/base/dd.c:1006) [ 5.419929] #3: ffffff88039c8268 (request_class#2){+.+.}-{4:4}, at: __setup_irq (kernel/irq/internals.h:156 kernel/irq/manage.c:1596) [ 5.428331] #4: ffffff88039c80c8 (lock_class#2){....}-{2:2}, at: __setup_irq (kernel/irq/manage.c:1614) [ 5.436472] stack backtrace: [ 5.439359] CPU: 2 UID: 0 PID: 44 Comm: kworker/u17:1 Tainted: G W 6.13.0-rc5+ #69 [ 5.448690] Tainted: [W]=WARN [ 5.451656] Hardware name: xlnx,zynqmp (DT) [ 5.455845] Workqueue: events_unbound deferred_probe_work_func [ 5.461699] Call trace: [ 5.464147] show_stack+0x18/0x24 C [ 5.467821] dump_stack_lvl (lib/dump_stack.c:123) [ 5.471501] dump_stack (lib/dump_stack.c:130) [ 5.474824] __lock_acquire (kernel/locking/lockdep.c:4828 kernel/locking/lockdep.c:4898 kernel/locking/lockdep.c:5176) [ 5.478758] lock_acquire (arch/arm64/include/asm/percpu.h:40 kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5851 kernel/locking/lockdep.c:5814) [ 5.482429] _raw_spin_lock_irqsave (include/linux/spinlock_api_smp.h:111 kernel/locking/spinlock.c:162) [ 5.486797] xgpio_irq_unmask (drivers/gpio/gpio-xilinx.c:433 (discriminator 8)) [ 5.490737] irq_enable (kernel/irq/internals.h:236 kernel/irq/chip.c:170 kernel/irq/chip.c:439 kernel/irq/chip.c:432 kernel/irq/chip.c:345) [ 5.494060] __irq_startup (kernel/irq/internals.h:241 kernel/irq/chip.c:180 kernel/irq/chip.c:250) [ 5.497645] irq_startup (kernel/irq/chip.c:270) [ 5.501143] __setup_irq (kernel/irq/manage.c:1807) [ 5.504728] request_threaded_irq (kernel/irq/manage.c:2208)

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Fix warnings during S3 suspend The enable_gpe_wakeup() function calls acpi_enable_all_wakeup_gpes(), and the later one may call the preempt_schedule_common() function, resulting in a thread switch and causing the CPU to be in an interrupt enabled state after the enable_gpe_wakeup() function returns, leading to the warnings as follow. [ C0] WARNING: ... at kernel/time/timekeeping.c:845 ktime_get+0xbc/0xc8 [ C0] ... [ C0] Call Trace: [ C0] [<90000000002243b4>] show_stack+0x64/0x188 [ C0] [<900000000164673c>] dump_stack_lvl+0x60/0x88 [ C0] [<90000000002687e4>] __warn+0x8c/0x148 [ C0] [<90000000015e9978>] report_bug+0x1c0/0x2b0 [ C0] [<90000000016478e4>] do_bp+0x204/0x3b8 [ C0] [<90000000025b1924>] exception_handlers+0x1924/0x10000 [ C0] [<9000000000343bbc>] ktime_get+0xbc/0xc8 [ C0] [<9000000000354c08>] tick_sched_timer+0x30/0xb0 [ C0] [<90000000003408e0>] __hrtimer_run_queues+0x160/0x378 [ C0] [<9000000000341f14>] hrtimer_interrupt+0x144/0x388 [ C0] [<9000000000228348>] constant_timer_interrupt+0x38/0x48 [ C0] [<90000000002feba4>] __handle_irq_event_percpu+0x64/0x1e8 [ C0] [<90000000002fed48>] handle_irq_event_percpu+0x20/0x80 [ C0] [<9000000000306b9c>] handle_percpu_irq+0x5c/0x98 [ C0] [<90000000002fd4a0>] generic_handle_domain_irq+0x30/0x48 [ C0] [<9000000000d0c7b0>] handle_cpu_irq+0x70/0xa8 [ C0] [<9000000001646b30>] handle_loongarch_irq+0x30/0x48 [ C0] [<9000000001646bc8>] do_vint+0x80/0xe0 [ C0] [<90000000002aea1c>] finish_task_switch.isra.0+0x8c/0x2a8 [ C0] [<900000000164e34c>] __schedule+0x314/0xa48 [ C0] [<900000000164ead8>] schedule+0x58/0xf0 [ C0] [<9000000000294a2c>] worker_thread+0x224/0x498 [ C0] [<900000000029d2f0>] kthread+0xf8/0x108 [ C0] [<9000000000221f28>] ret_from_kernel_thread+0xc/0xa4 [ C0] [ C0] ---[ end trace 0000000000000000 ]--- The root cause is acpi_enable_all_wakeup_gpes() uses a mutex to protect acpi_hw_enable_all_wakeup_gpes(), and acpi_ut_acquire_mutex() may cause a thread switch. Since there is no longer concurrent execution during loongarch_acpi_suspend(), we can call acpi_hw_enable_all_wakeup_gpes() directly in enable_gpe_wakeup(). The solution is similar to commit 22db06337f590d01 ("ACPI: sleep: Avoid breaking S3 wakeup due to might_sleep()").

In the Linux kernel, the following vulnerability has been resolved: mtd: spi-nor: sst: Fix SST write failure 'commit 18bcb4aa54ea ("mtd: spi-nor: sst: Factor out common write operation to `sst_nor_write_data()`")' introduced a bug where only one byte of data is written, regardless of the number of bytes passed to sst_nor_write_data(), causing a kernel crash during the write operation. Ensure the correct number of bytes are written as passed to sst_nor_write_data(). Call trace: [ 57.400180] ------------[ cut here ]------------ [ 57.404842] While writing 2 byte written 1 bytes [ 57.409493] WARNING: CPU: 0 PID: 737 at drivers/mtd/spi-nor/sst.c:187 sst_nor_write_data+0x6c/0x74 [ 57.418464] Modules linked in: [ 57.421517] CPU: 0 UID: 0 PID: 737 Comm: mtd_debug Not tainted 6.12.0-g5ad04afd91f9 #30 [ 57.429517] Hardware name: Xilinx Versal A2197 Processor board revA - x-prc-02 revA (DT) [ 57.437600] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 57.444557] pc : sst_nor_write_data+0x6c/0x74 [ 57.448911] lr : sst_nor_write_data+0x6c/0x74 [ 57.453264] sp : ffff80008232bb40 [ 57.456570] x29: ffff80008232bb40 x28: 0000000000010000 x27: 0000000000000001 [ 57.463708] x26: 000000000000ffff x25: 0000000000000000 x24: 0000000000000000 [ 57.470843] x23: 0000000000010000 x22: ffff80008232bbf0 x21: ffff000816230000 [ 57.477978] x20: ffff0008056c0080 x19: 0000000000000002 x18: 0000000000000006 [ 57.485112] x17: 0000000000000000 x16: 0000000000000000 x15: ffff80008232b580 [ 57.492246] x14: 0000000000000000 x13: ffff8000816d1530 x12: 00000000000004a4 [ 57.499380] x11: 000000000000018c x10: ffff8000816fd530 x9 : ffff8000816d1530 [ 57.506515] x8 : 00000000fffff7ff x7 : ffff8000816fd530 x6 : 0000000000000001 [ 57.513649] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 [ 57.520782] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff0008049b0000 [ 57.527916] Call trace: [ 57.530354] sst_nor_write_data+0x6c/0x74 [ 57.534361] sst_nor_write+0xb4/0x18c [ 57.538019] mtd_write_oob_std+0x7c/0x88 [ 57.541941] mtd_write_oob+0x70/0xbc [ 57.545511] mtd_write+0x68/0xa8 [ 57.548733] mtdchar_write+0x10c/0x290 [ 57.552477] vfs_write+0xb4/0x3a8 [ 57.555791] ksys_write+0x74/0x10c [ 57.559189] __arm64_sys_write+0x1c/0x28 [ 57.563109] invoke_syscall+0x54/0x11c [ 57.566856] el0_svc_common.constprop.0+0xc0/0xe0 [ 57.571557] do_el0_svc+0x1c/0x28 [ 57.574868] el0_svc+0x30/0xcc [ 57.577921] el0t_64_sync_handler+0x120/0x12c [ 57.582276] el0t_64_sync+0x190/0x194 [ 57.585933] ---[ end trace 0000000000000000 ]--- [pratyush@kernel.org: add Cc stable tag]

In the Linux kernel, the following vulnerability has been resolved: ksmbd: prevent connection release during oplock break notification ksmbd_work could be freed when after connection release. Increment r_count of ksmbd_conn to indicate that requests are not finished yet and to not release the connection.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5: Fix vport QoS cleanup on error When enabling vport QoS fails, the scheduling node was never freed, causing a leak. Add the missing free and reset the vport scheduling node pointer to NULL.

In the Linux kernel, the following vulnerability has been resolved: staging: vchiq_arm: Fix possible NPR of keep-alive thread In case vchiq_platform_conn_state_changed() is never called or fails before driver removal, ka_thread won't be a valid pointer to a task_struct. So do the necessary checks before calling kthread_stop to avoid a crash.

In the Linux kernel, the following vulnerability has been resolved: eth: bnxt: return fail if interface is down in bnxt_queue_mem_alloc() The bnxt_queue_mem_alloc() is called to allocate new queue memory when a queue is restarted. It internally accesses rx buffer descriptor corresponding to the index. The rx buffer descriptor is allocated and set when the interface is up and it's freed when the interface is down. So, if queue is restarted if interface is down, kernel panic occurs. Splat looks like: BUG: unable to handle page fault for address: 000000000000b240 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 3 UID: 0 PID: 1563 Comm: ncdevmem2 Not tainted 6.14.0-rc2+ #9 844ddba6e7c459cafd0bf4db9a3198e Hardware name: ASUS System Product Name/PRIME Z690-P D4, BIOS 0603 11/01/2021 RIP: 0010:bnxt_queue_mem_alloc+0x3f/0x4e0 [bnxt_en] Code: 41 54 4d 89 c4 4d 69 c0 c0 05 00 00 55 48 89 f5 53 48 89 fb 4c 8d b5 40 05 00 00 48 83 ec 15 RSP: 0018:ffff9dcc83fef9e8 EFLAGS: 00010202 RAX: ffffffffc0457720 RBX: ffff934ed8d40000 RCX: 0000000000000000 RDX: 000000000000001f RSI: ffff934ea508f800 RDI: ffff934ea508f808 RBP: ffff934ea508f800 R08: 000000000000b240 R09: ffff934e84f4b000 R10: ffff9dcc83fefa30 R11: ffff934e84f4b000 R12: 000000000000001f R13: ffff934ed8d40ac0 R14: ffff934ea508fd40 R15: ffff934e84f4b000 FS: 00007fa73888c740(0000) GS:ffff93559f780000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000b240 CR3: 0000000145a2e000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <TASK> ? __die+0x20/0x70 ? page_fault_oops+0x15a/0x460 ? exc_page_fault+0x6e/0x180 ? asm_exc_page_fault+0x22/0x30 ? __pfx_bnxt_queue_mem_alloc+0x10/0x10 [bnxt_en 7f85e76f4d724ba07471d7e39d9e773aea6597b7] ? bnxt_queue_mem_alloc+0x3f/0x4e0 [bnxt_en 7f85e76f4d724ba07471d7e39d9e773aea6597b7] netdev_rx_queue_restart+0xc5/0x240 net_devmem_bind_dmabuf_to_queue+0xf8/0x200 netdev_nl_bind_rx_doit+0x3a7/0x450 genl_family_rcv_msg_doit+0xd9/0x130 genl_rcv_msg+0x184/0x2b0 ? __pfx_netdev_nl_bind_rx_doit+0x10/0x10 ? __pfx_genl_rcv_msg+0x10/0x10 netlink_rcv_skb+0x54/0x100 genl_rcv+0x24/0x40 ...

In the Linux kernel, the following vulnerability has been resolved: ext4: avoid journaling sb update on error if journal is destroying Presently we always BUG_ON if trying to start a transaction on a journal marked with JBD2_UNMOUNT, since this should never happen. However, while ltp running stress tests, it was observed that in case of some error handling paths, it is possible for update_super_work to start a transaction after the journal is destroyed eg: (umount) ext4_kill_sb kill_block_super generic_shutdown_super sync_filesystem /* commits all txns */ evict_inodes /* might start a new txn */ ext4_put_super flush_work(&sbi->s_sb_upd_work) /* flush the workqueue */ jbd2_journal_destroy journal_kill_thread journal->j_flags |= JBD2_UNMOUNT; jbd2_journal_commit_transaction jbd2_journal_get_descriptor_buffer jbd2_journal_bmap ext4_journal_bmap ext4_map_blocks ... ext4_inode_error ext4_handle_error schedule_work(&sbi->s_sb_upd_work) /* work queue kicks in */ update_super_work jbd2_journal_start start_this_handle BUG_ON(journal->j_flags & JBD2_UNMOUNT) Hence, introduce a new mount flag to indicate journal is destroying and only do a journaled (and deferred) update of sb if this flag is not set. Otherwise, just fallback to an un-journaled commit. Further, in the journal destroy path, we have the following sequence: 1. Set mount flag indicating journal is destroying 2. force a commit and wait for it 3. flush pending sb updates This sequence is important as it ensures that, after this point, there is no sb update that might be journaled so it is safe to update the sb outside the journal. (To avoid race discussed in 2d01ddc86606) Also, we don't need a similar check in ext4_grp_locked_error since it is only called from mballoc and AFAICT it would be always valid to schedule work here.

In the Linux kernel, the following vulnerability has been resolved: udp: Fix multiple wraparounds of sk->sk_rmem_alloc. __udp_enqueue_schedule_skb() has the following condition: if (atomic_read(&sk->sk_rmem_alloc) > sk->sk_rcvbuf) goto drop; sk->sk_rcvbuf is initialised by net.core.rmem_default and later can be configured by SO_RCVBUF, which is limited by net.core.rmem_max, or SO_RCVBUFFORCE. If we set INT_MAX to sk->sk_rcvbuf, the condition is always false as sk->sk_rmem_alloc is also signed int. Then, the size of the incoming skb is added to sk->sk_rmem_alloc unconditionally. This results in integer overflow (possibly multiple times) on sk->sk_rmem_alloc and allows a single socket to have skb up to net.core.udp_mem[1]. For example, if we set a large value to udp_mem[1] and INT_MAX to sk->sk_rcvbuf and flood packets to the socket, we can see multiple overflows: # cat /proc/net/sockstat | grep UDP: UDP: inuse 3 mem 7956736 <-- (7956736 << 12) bytes > INT_MAX * 15 ^- PAGE_SHIFT # ss -uam State Recv-Q ... UNCONN -1757018048 ... <-- flipping the sign repeatedly skmem:(r2537949248,rb2147483646,t0,tb212992,f1984,w0,o0,bl0,d0) Previously, we had a boundary check for INT_MAX, which was removed by commit 6a1f12dd85a8 ("udp: relax atomic operation on sk->sk_rmem_alloc"). A complete fix would be to revert it and cap the right operand by INT_MAX: rmem = atomic_add_return(size, &sk->sk_rmem_alloc); if (rmem > min(size + (unsigned int)sk->sk_rcvbuf, INT_MAX)) goto uncharge_drop; but we do not want to add the expensive atomic_add_return() back just for the corner case. Casting rmem to unsigned int prevents multiple wraparounds, but we still allow a single wraparound. # cat /proc/net/sockstat | grep UDP: UDP: inuse 3 mem 524288 <-- (INT_MAX + 1) >> 12 # ss -uam State Recv-Q ... UNCONN -2147482816 ... <-- INT_MAX + 831 bytes skmem:(r2147484480,rb2147483646,t0,tb212992,f3264,w0,o0,bl0,d14468947) So, let's define rmem and rcvbuf as unsigned int and check skb->truesize only when rcvbuf is large enough to lower the overflow possibility. Note that we still have a small chance to see overflow if multiple skbs to the same socket are processed on different core at the same time and each size does not exceed the limit but the total size does. Note also that we must ignore skb->truesize for a small buffer as explained in commit 363dc73acacb ("udp: be less conservative with sock rmem accounting").

In the Linux kernel, the following vulnerability has been resolved: bonding: check xdp prog when set bond mode Following operations can trigger a warning[1]: ip netns add ns1 ip netns exec ns1 ip link add bond0 type bond mode balance-rr ip netns exec ns1 ip link set dev bond0 xdp obj af_xdp_kern.o sec xdp ip netns exec ns1 ip link set bond0 type bond mode broadcast ip netns del ns1 When delete the namespace, dev_xdp_uninstall() is called to remove xdp program on bond dev, and bond_xdp_set() will check the bond mode. If bond mode is changed after attaching xdp program, the warning may occur. Some bond modes (broadcast, etc.) do not support native xdp. Set bond mode with xdp program attached is not good. Add check for xdp program when set bond mode. [1] ------------[ cut here ]------------ WARNING: CPU: 0 PID: 11 at net/core/dev.c:9912 unregister_netdevice_many_notify+0x8d9/0x930 Modules linked in: CPU: 0 UID: 0 PID: 11 Comm: kworker/u4:0 Not tainted 6.14.0-rc4 #107 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 Workqueue: netns cleanup_net RIP: 0010:unregister_netdevice_many_notify+0x8d9/0x930 Code: 00 00 48 c7 c6 6f e3 a2 82 48 c7 c7 d0 b3 96 82 e8 9c 10 3e ... RSP: 0018:ffffc90000063d80 EFLAGS: 00000282 RAX: 00000000ffffffa1 RBX: ffff888004959000 RCX: 00000000ffffdfff RDX: 0000000000000000 RSI: 00000000ffffffea RDI: ffffc90000063b48 RBP: ffffc90000063e28 R08: ffffffff82d39b28 R09: 0000000000009ffb R10: 0000000000000175 R11: ffffffff82d09b40 R12: ffff8880049598e8 R13: 0000000000000001 R14: dead000000000100 R15: ffffc90000045000 FS: 0000000000000000(0000) GS:ffff888007a00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000d406b60 CR3: 000000000483e000 CR4: 00000000000006f0 Call Trace: <TASK> ? __warn+0x83/0x130 ? unregister_netdevice_many_notify+0x8d9/0x930 ? report_bug+0x18e/0x1a0 ? handle_bug+0x54/0x90 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? unregister_netdevice_many_notify+0x8d9/0x930 ? bond_net_exit_batch_rtnl+0x5c/0x90 cleanup_net+0x237/0x3d0 process_one_work+0x163/0x390 worker_thread+0x293/0x3b0 ? __pfx_worker_thread+0x10/0x10 kthread+0xec/0x1e0 ? __pfx_kthread+0x10/0x10 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x2f/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Assign normalized_pix_clk when color depth = 14 [WHY & HOW] A warning message "WARNING: CPU: 4 PID: 459 at ... /dc_resource.c:3397 calculate_phy_pix_clks+0xef/0x100 [amdgpu]" occurs because the display_color_depth == COLOR_DEPTH_141414 is not handled. This is observed in Radeon RX 6600 XT. It is fixed by assigning pix_clk * (14 * 3) / 24 - same as the rests. Also fixes the indentation in get_norm_pix_clk. (cherry picked from commit 274a87eb389f58eddcbc5659ab0b180b37e92775)

In the Linux kernel, the following vulnerability has been resolved: block: fix adding folio to bio >4GB folio is possible on some ARCHs, such as aarch64, 16GB hugepage is supported, then 'offset' of folio can't be held in 'unsigned int', cause warning in bio_add_folio_nofail() and IO failure. Fix it by adjusting 'page' & trimming 'offset' so that `->bi_offset` won't be overflow, and folio can be added to bio successfully.

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface() The documentation for usb_driver_claim_interface() says that "the device lock" is needed when the function is called from places other than probe(). This appears to be the lock for the USB interface device. The Mediatek btusb code gets called via this path: Workqueue: hci0 hci_power_on [bluetooth] Call trace: usb_driver_claim_interface btusb_mtk_claim_iso_intf btusb_mtk_setup hci_dev_open_sync hci_power_on process_scheduled_works worker_thread kthread With the above call trace the device lock hasn't been claimed. Claim it. Without this fix, we'd sometimes see the error "Failed to claim iso interface". Sometimes we'd even see worse errors, like a NULL pointer dereference (where `intf->dev.driver` was NULL) with a trace like: Call trace: usb_suspend_both usb_runtime_suspend __rpm_callback rpm_suspend pm_runtime_work process_scheduled_works Both errors appear to be fixed with the proper locking.

In the Linux kernel, the following vulnerability has been resolved: sched_ext: Fix pick_task_scx() picking non-queued tasks when it's called without balance() a6250aa251ea ("sched_ext: Handle cases where pick_task_scx() is called without preceding balance_scx()") added a workaround to handle the cases where pick_task_scx() is called without prececing balance_scx() which is due to a fair class bug where pick_taks_fair() may return NULL after a true return from balance_fair(). The workaround detects when pick_task_scx() is called without preceding balance_scx() and emulates SCX_RQ_BAL_KEEP and triggers kicking to avoid stalling. Unfortunately, the workaround code was testing whether @prev was on SCX to decide whether to keep the task running. This is incorrect as the task may be on SCX but no longer runnable. This could lead to a non-runnable task to be returned from pick_task_scx() which cause interesting confusions and failures. e.g. A common failure mode is the task ending up with (!on_rq && on_cpu) state which can cause potential wakers to busy loop, which can easily lead to deadlocks. Fix it by testing whether @prev has SCX_TASK_QUEUED set. This makes @prev_on_scx only used in one place. Open code the usage and improve the comment while at it.

In the Linux kernel, the following vulnerability has been resolved: net: stmmac: dwmac-tegra: Read iommu stream id from device tree Nvidia's Tegra MGBE controllers require the IOMMU "Stream ID" (SID) to be written to the MGBE_WRAP_AXI_ASID0_CTRL register. The current driver is hard coded to use MGBE0's SID for all controllers. This causes softirq time outs and kernel panics when using controllers other than MGBE0. Example dmesg errors when an ethernet cable is connected to MGBE1: [ 116.133290] tegra-mgbe 6910000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx [ 121.851283] tegra-mgbe 6910000.ethernet eth1: NETDEV WATCHDOG: CPU: 5: transmit queue 0 timed out 5690 ms [ 121.851782] tegra-mgbe 6910000.ethernet eth1: Reset adapter. [ 121.892464] tegra-mgbe 6910000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 121.905920] tegra-mgbe 6910000.ethernet eth1: PHY [stmmac-1:00] driver [Aquantia AQR113] (irq=171) [ 121.907356] tegra-mgbe 6910000.ethernet eth1: Enabling Safety Features [ 121.907578] tegra-mgbe 6910000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 121.908399] tegra-mgbe 6910000.ethernet eth1: registered PTP clock [ 121.908582] tegra-mgbe 6910000.ethernet eth1: configuring for phy/10gbase-r link mode [ 125.961292] tegra-mgbe 6910000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx [ 181.921198] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks: [ 181.921404] rcu: 7-....: (1 GPs behind) idle=540c/1/0x4000000000000002 softirq=1748/1749 fqs=2337 [ 181.921684] rcu: (detected by 4, t=6002 jiffies, g=1357, q=1254 ncpus=8) [ 181.921878] Sending NMI from CPU 4 to CPUs 7: [ 181.921886] NMI backtrace for cpu 7 [ 181.922131] CPU: 7 UID: 0 PID: 0 Comm: swapper/7 Kdump: loaded Not tainted 6.13.0-rc3+ #6 [ 181.922390] Hardware name: NVIDIA CTI Forge + Orin AGX/Jetson, BIOS 202402.1-Unknown 10/28/2024 [ 181.922658] pstate: 40400009 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 181.922847] pc : handle_softirqs+0x98/0x368 [ 181.922978] lr : __do_softirq+0x18/0x20 [ 181.923095] sp : ffff80008003bf50 [ 181.923189] x29: ffff80008003bf50 x28: 0000000000000008 x27: 0000000000000000 [ 181.923379] x26: ffffce78ea277000 x25: 0000000000000000 x24: 0000001c61befda0 [ 181.924486] x23: 0000000060400009 x22: ffffce78e99918bc x21: ffff80008018bd70 [ 181.925568] x20: ffffce78e8bb00d8 x19: ffff80008018bc20 x18: 0000000000000000 [ 181.926655] x17: ffff318ebe7d3000 x16: ffff800080038000 x15: 0000000000000000 [ 181.931455] x14: ffff000080816680 x13: ffff318ebe7d3000 x12: 000000003464d91d [ 181.938628] x11: 0000000000000040 x10: ffff000080165a70 x9 : ffffce78e8bb0160 [ 181.945804] x8 : ffff8000827b3160 x7 : f9157b241586f343 x6 : eeb6502a01c81c74 [ 181.953068] x5 : a4acfcdd2e8096bb x4 : ffffce78ea277340 x3 : 00000000ffffd1e1 [ 181.960329] x2 : 0000000000000101 x1 : ffffce78ea277340 x0 : ffff318ebe7d3000 [ 181.967591] Call trace: [ 181.970043] handle_softirqs+0x98/0x368 (P) [ 181.974240] __do_softirq+0x18/0x20 [ 181.977743] ____do_softirq+0x14/0x28 [ 181.981415] call_on_irq_stack+0x24/0x30 [ 181.985180] do_softirq_own_stack+0x20/0x30 [ 181.989379] __irq_exit_rcu+0x114/0x140 [ 181.993142] irq_exit_rcu+0x14/0x28 [ 181.996816] el1_interrupt+0x44/0xb8 [ 182.000316] el1h_64_irq_handler+0x14/0x20 [ 182.004343] el1h_64_irq+0x80/0x88 [ 182.007755] cpuidle_enter_state+0xc4/0x4a8 (P) [ 182.012305] cpuidle_enter+0x3c/0x58 [ 182.015980] cpuidle_idle_call+0x128/0x1c0 [ 182.020005] do_idle+0xe0/0xf0 [ 182.023155] cpu_startup_entry+0x3c/0x48 [ 182.026917] secondary_start_kernel+0xdc/0x120 [ 182.031379] __secondary_switched+0x74/0x78 [ 212.971162] rcu: INFO: rcu_preempt detected expedited stalls on CPUs/tasks: { 7-.... } 6103 jiffies s: 417 root: 0x80/. [ 212.985935] rcu: blocking rcu_node structures (internal RCU debug): [ 212.992758] Sending NMI from CPU 0 to CPUs 7: [ 212.998539] NMI backtrace for cpu 7 [ 213.004304] CPU: 7 UID: 0 PI ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: iwlwifi: mvm: don't try to talk to a dead firmware This fixes: bad state = 0 WARNING: CPU: 10 PID: 702 at drivers/net/wireless/inel/iwlwifi/iwl-trans.c:178 iwl_trans_send_cmd+0xba/0xe0 [iwlwifi] Call Trace: <TASK> ? __warn+0xca/0x1c0 ? iwl_trans_send_cmd+0xba/0xe0 [iwlwifi 64fa9ad799a0e0d2ba53d4af93a53ad9a531f8d4] iwl_fw_dbg_clear_monitor_buf+0xd7/0x110 [iwlwifi 64fa9ad799a0e0d2ba53d4af93a53ad9a531f8d4] _iwl_dbgfs_fw_dbg_clear_write+0xe2/0x120 [iwlmvm 0e8adb18cea92d2c341766bcc10b18699290068a] Ask whether the firmware is alive before sending a command.

In the Linux kernel, the following vulnerability has been resolved: regulator: check that dummy regulator has been probed before using it Due to asynchronous driver probing there is a chance that the dummy regulator hasn't already been probed when first accessing it.

In the Linux kernel, the following vulnerability has been resolved: ice: fix using untrusted value of pkt_len in ice_vc_fdir_parse_raw() Fix using the untrusted value of proto->raw.pkt_len in function ice_vc_fdir_parse_raw() by verifying if it does not exceed the VIRTCHNL_MAX_SIZE_RAW_PACKET value.

In the Linux kernel, the following vulnerability has been resolved: tcp: add sanity tests to TCP_QUEUE_SEQ Qingyu Li reported a syzkaller bug where the repro changes RCV SEQ _after_ restoring data in the receive queue. mprotect(0x4aa000, 12288, PROT_READ) = 0 mmap(0x1ffff000, 4096, PROT_NONE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x1ffff000 mmap(0x20000000, 16777216, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x20000000 mmap(0x21000000, 4096, PROT_NONE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x21000000 socket(AF_INET6, SOCK_STREAM, IPPROTO_IP) = 3 setsockopt(3, SOL_TCP, TCP_REPAIR, [1], 4) = 0 connect(3, {sa_family=AF_INET6, sin6_port=htons(0), sin6_flowinfo=htonl(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_scope_id=0}, 28) = 0 setsockopt(3, SOL_TCP, TCP_REPAIR_QUEUE, [1], 4) = 0 sendmsg(3, {msg_name=NULL, msg_namelen=0, msg_iov=[{iov_base="0x0000000000000003\0\0", iov_len=20}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 20 setsockopt(3, SOL_TCP, TCP_REPAIR, [0], 4) = 0 setsockopt(3, SOL_TCP, TCP_QUEUE_SEQ, [128], 4) = 0 recvfrom(3, NULL, 20, 0, NULL, NULL) = -1 ECONNRESET (Connection reset by peer) syslog shows: [ 111.205099] TCP recvmsg seq # bug 2: copied 80, seq 0, rcvnxt 80, fl 0 [ 111.207894] WARNING: CPU: 1 PID: 356 at net/ipv4/tcp.c:2343 tcp_recvmsg_locked+0x90e/0x29a0 This should not be allowed. TCP_QUEUE_SEQ should only be used when queues are empty. This patch fixes this case, and the tx path as well.

In the Linux kernel, the following vulnerability has been resolved: ptp: vmclock: Set driver data before its usage If vmclock_ptp_register() fails during probing, vmclock_remove() is called to clean up the ptp clock and misc device. It uses dev_get_drvdata() to access the vmclock state. However the driver data is not yet set at this point. Assign the driver data earlier.

An issue was discovered in the Linux kernel before 5.14.15. There is an array-index-out-of-bounds flaw in the detach_capi_ctr function in drivers/isdn/capi/kcapi.c.

In the Linux kernel, the following vulnerability has been resolved: drm/panthor: avoid garbage value in panthor_ioctl_dev_query() 'priorities_info' is uninitialized, and the uninitialized value is copied to user object when calling PANTHOR_UOBJ_SET(). Using memset to initialize 'priorities_info' to avoid this garbage value problem.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: reject mismatching sum of field_len with set key length The field length description provides the length of each separated key field in the concatenation, each field gets rounded up to 32-bits to calculate the pipapo rule width from pipapo_init(). The set key length provides the total size of the key aligned to 32-bits. Register-based arithmetics still allows for combining mismatching set key length and field length description, eg. set key length 10 and field description [ 5, 4 ] leading to pipapo width of 12.

In the Linux kernel, the following vulnerability has been resolved: scsi: ses: Handle enclosure with just a primary component gracefully This reverts commit 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components") and introduces proper handling of case where there are no detected secondary components, but primary component (enumerated in num_enclosures) does exist. That fix was originally proposed by Ding Hui <dinghui@sangfor.com.cn>. Completely ignoring devices that have one primary enclosure and no secondary one results in ses_intf_add() bailing completely scsi 2:0:0:254: enclosure has no enumerated components scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such even on valid configurations with 1 primary and 0 secondary enclosures as below: # sg_ses /dev/sg0 3PARdata SES 3321 Supported diagnostic pages: Supported Diagnostic Pages [sdp] [0x0] Configuration (SES) [cf] [0x1] Short Enclosure Status (SES) [ses] [0x8] # sg_ses -p cf /dev/sg0 3PARdata SES 3321 Configuration diagnostic page: number of secondary subenclosures: 0 generation code: 0x0 enclosure descriptor list Subenclosure identifier: 0 [primary] relative ES process id: 0, number of ES processes: 1 number of type descriptor headers: 1 enclosure logical identifier (hex): 20000002ac02068d enclosure vendor: 3PARdata product: VV rev: 3321 type descriptor header and text list Element type: Unspecified, subenclosure id: 0 number of possible elements: 1 The changelog for the original fix follows ===== We can get a crash when disconnecting the iSCSI session, the call trace like this: [ffff00002a00fb70] kfree at ffff00000830e224 [ffff00002a00fba0] ses_intf_remove at ffff000001f200e4 [ffff00002a00fbd0] device_del at ffff0000086b6a98 [ffff00002a00fc50] device_unregister at ffff0000086b6d58 [ffff00002a00fc70] __scsi_remove_device at ffff00000870608c [ffff00002a00fca0] scsi_remove_device at ffff000008706134 [ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4 [ffff00002a00fd10] scsi_remove_target at ffff0000087064c0 [ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4 [ffff00002a00fdb0] process_one_work at ffff00000810f35c [ffff00002a00fe00] worker_thread at ffff00000810f648 [ffff00002a00fe70] kthread at ffff000008116e98 In ses_intf_add, components count could be 0, and kcalloc 0 size scomp, but not saved in edev->component[i].scratch In this situation, edev->component[0].scratch is an invalid pointer, when kfree it in ses_intf_remove_enclosure, a crash like above would happen The call trace also could be other random cases when kfree cannot catch the invalid pointer We should not use edev->component[] array when the components count is 0 We also need check index when use edev->component[] array in ses_enclosure_data_process =====

In the Linux kernel, the following vulnerability has been resolved: net/rose: prevent integer overflows in rose_setsockopt() In case of possible unpredictably large arguments passed to rose_setsockopt() and multiplied by extra values on top of that, integer overflows may occur. Do the safest minimum and fix these issues by checking the contents of 'opt' and returning -EINVAL if they are too large. Also, switch to unsigned int and remove useless check for negative 'opt' in ROSE_IDLE case.

In the Linux kernel, the following vulnerability has been resolved: timers/migration: Fix off-by-one root mis-connection Before attaching a new root to the old root, the children counter of the new root is checked to verify that only the upcoming CPU's top group have been connected to it. However since the recently added commit b729cc1ec21a ("timers/migration: Fix another race between hotplug and idle entry/exit") this check is not valid anymore because the old root is pre-accounted as a child to the new root. Therefore after connecting the upcoming CPU's top group to the new root, the children count to be expected must be 2 and not 1 anymore. This omission results in the old root to not be connected to the new root. Then eventually the system may run with more than one top level, which defeats the purpose of a single idle migrator. Also the old root is pre-accounted but not connected upon the new root creation. But it can be connected to the new root later on. Therefore the old root may be accounted twice to the new root. The propagation of such overcommit can end up creating a double final top-level root with a groupmask incorrectly initialized. Although harmless given that the final top level roots will never have a parent to walk up to, this oddity opportunistically reported the core issue: WARNING: CPU: 8 PID: 0 at kernel/time/timer_migration.c:543 tmigr_requires_handle_remote CPU: 8 UID: 0 PID: 0 Comm: swapper/8 RIP: 0010:tmigr_requires_handle_remote Call Trace: <IRQ> ? tmigr_requires_handle_remote ? hrtimer_run_queues update_process_times tick_periodic tick_handle_periodic __sysvec_apic_timer_interrupt sysvec_apic_timer_interrupt </IRQ> Fix the problem by taking the old root into account in the children count of the new root so the connection is not omitted. Also warn when more than one top level group exists to better detect similar issues in the future.

In the Linux kernel, the following vulnerability has been resolved: net: xdp: Disallow attaching device-bound programs in generic mode Device-bound programs are used to support RX metadata kfuncs. These kfuncs are driver-specific and rely on the driver context to read the metadata. This means they can't work in generic XDP mode. However, there is no check to disallow such programs from being attached in generic mode, in which case the metadata kfuncs will be called in an invalid context, leading to crashes. Fix this by adding a check to disallow attaching device-bound programs in generic mode.

In the Linux kernel, the following vulnerability has been resolved: spufs: fix a leak in spufs_create_context() Leak fixes back in 2008 missed one case - if we are trying to set affinity and spufs_mkdir() fails, we need to drop the reference to neighbor.

In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix bug on trap in smb2_lock If lock count is greater than 1, flags could be old value. It should be checked with flags of smb_lock, not flags. It will cause bug-on trap from locks_free_lock in error handling routine.

In the Linux kernel, the following vulnerability has been resolved: blk-cgroup: Fix class @block_class's subsystem refcount leakage blkcg_fill_root_iostats() iterates over @block_class's devices by class_dev_iter_(init|next)(), but does not end iterating with class_dev_iter_exit(), so causes the class's subsystem refcount leakage. Fix by ending the iterating with class_dev_iter_exit().

In the Linux kernel, the following vulnerability has been resolved: drm/vc4: drop all currently held locks if deadlock happens If vc4_hdmi_reset_link() returns -EDEADLK, it means that a deadlock happened in the locking context. This situation should be addressed by dropping all currently held locks and block until the contended lock becomes available. Currently, vc4 is not dealing with the deadlock properly, producing the following output when PROVE_LOCKING is enabled: [ 825.612809] ------------[ cut here ]------------ [ 825.612852] WARNING: CPU: 1 PID: 116 at drivers/gpu/drm/drm_modeset_lock.c:276 drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.613458] Modules linked in: 8021q mrp garp stp llc raspberrypi_cpufreq brcmfmac brcmutil crct10dif_ce hci_uart cfg80211 btqca btbcm bluetooth vc4 raspberrypi_hwmon snd_soc_hdmi_codec cec clk_raspberrypi ecdh_generic drm_display_helper ecc rfkill drm_dma_helper drm_kms_helper pwm_bcm2835 bcm2835_thermal bcm2835_rng rng_core i2c_bcm2835 drm fuse ip_tables x_tables ipv6 [ 825.613735] CPU: 1 PID: 116 Comm: kworker/1:2 Tainted: G W 6.1.0-rc6-01399-g941aae326315 #3 [ 825.613759] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT) [ 825.613777] Workqueue: events output_poll_execute [drm_kms_helper] [ 825.614038] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 825.614063] pc : drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.614603] lr : drm_helper_probe_detect+0x120/0x1b4 [drm_kms_helper] [ 825.614829] sp : ffff800008313bf0 [ 825.614844] x29: ffff800008313bf0 x28: ffffcd7778b8b000 x27: 0000000000000000 [ 825.614883] x26: 0000000000000001 x25: 0000000000000001 x24: ffff677cc35c2758 [ 825.614920] x23: ffffcd7707d01430 x22: ffffcd7707c3edc7 x21: 0000000000000001 [ 825.614958] x20: 0000000000000000 x19: ffff800008313c10 x18: 000000000000b6d3 [ 825.614995] x17: ffffcd777835e214 x16: ffffcd7777cef870 x15: fffff81000000000 [ 825.615033] x14: 0000000000000000 x13: 0000000000000099 x12: 0000000000000002 [ 825.615070] x11: 72917988020af800 x10: 72917988020af800 x9 : 72917988020af800 [ 825.615108] x8 : ffff677cc665e0a8 x7 : d00a8c180000110c x6 : ffffcd77774c0054 [ 825.615145] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000 [ 825.615181] x2 : ffff677cc55e1880 x1 : ffffcd7777cef8ec x0 : ffff800008313c10 [ 825.615219] Call trace: [ 825.615232] drm_modeset_drop_locks+0x60/0x68 [drm] [ 825.615773] drm_helper_probe_detect+0x120/0x1b4 [drm_kms_helper] [ 825.616003] output_poll_execute+0xe4/0x224 [drm_kms_helper] [ 825.616233] process_one_work+0x2b4/0x618 [ 825.616264] worker_thread+0x24c/0x464 [ 825.616288] kthread+0xec/0x110 [ 825.616310] ret_from_fork+0x10/0x20 [ 825.616335] irq event stamp: 7634 [ 825.616349] hardirqs last enabled at (7633): [<ffffcd777831ee90>] _raw_spin_unlock_irq+0x3c/0x78 [ 825.616384] hardirqs last disabled at (7634): [<ffffcd7778315a78>] __schedule+0x134/0x9f0 [ 825.616411] softirqs last enabled at (7630): [<ffffcd7707aacea0>] local_bh_enable+0x4/0x30 [ipv6] [ 825.617019] softirqs last disabled at (7618): [<ffffcd7707aace70>] local_bh_disable+0x4/0x30 [ipv6] [ 825.617586] ---[ end trace 0000000000000000 ]--- Therefore, deal with the deadlock as suggested by [1], using the function drm_modeset_backoff(). [1] https://docs.kernel.org/gpu/drm-kms.html?highlight=kms#kms-locking

In the Linux kernel, the following vulnerability has been resolved: x86/microcode/AMD: Fix __apply_microcode_amd()'s return value When verify_sha256_digest() fails, __apply_microcode_amd() should propagate the failure by returning false (and not -1 which is promoted to true).

In the Linux kernel, the following vulnerability has been resolved: tty: xilinx_uartps: split sysrq handling lockdep detects the following circular locking dependency: CPU 0 CPU 1 ========================== ============================ cdns_uart_isr() printk() uart_port_lock(port) console_lock() cdns_uart_console_write() if (!port->sysrq) uart_port_lock(port) uart_handle_break() port->sysrq = ... uart_handle_sysrq_char() printk() console_lock() The fixed commit attempts to avoid this situation by only taking the port lock in cdns_uart_console_write if port->sysrq unset. However, if (as shown above) cdns_uart_console_write runs before port->sysrq is set, then it will try to take the port lock anyway. This may result in a deadlock. Fix this by splitting sysrq handling into two parts. We use the prepare helper under the port lock and defer handling until we release the lock.

In the Linux kernel, the following vulnerability has been resolved: can: ucan: fix out of bound read in strscpy() source Commit 7fdaf8966aae ("can: ucan: use strscpy() to instead of strncpy()") unintentionally introduced a one byte out of bound read on strscpy()'s source argument (which is kind of ironic knowing that strscpy() is meant to be a more secure alternative :)). Let's consider below buffers: dest[len + 1]; /* will be NUL terminated */ src[len]; /* may not be NUL terminated */ When doing: strncpy(dest, src, len); dest[len] = '\0'; strncpy() will read up to len bytes from src. On the other hand: strscpy(dest, src, len + 1); will read up to len + 1 bytes from src, that is to say, an out of bound read of one byte will occur on src if it is not NUL terminated. Note that the src[len] byte is never copied, but strscpy() still needs to read it to check whether a truncation occurred or not. This exact pattern happened in ucan. The root cause is that the source is not NUL terminated. Instead of doing a copy in a local buffer, directly NUL terminate it as soon as usb_control_msg() returns. With this, the local firmware_str[] variable can be removed. On top of this do a couple refactors: - ucan_ctl_payload->raw is only used for the firmware string, so rename it to ucan_ctl_payload->fw_str and change its type from u8 to char. - ucan_device_request_in() is only used to retrieve the firmware string, so rename it to ucan_get_fw_str() and refactor it to make it directly handle all the string termination logic.