In the Linux kernel, the following vulnerability has been resolved: hv_netvsc: use kmap_local_page in netvsc_copy_to_send_buf netvsc_copy_to_send_buf() copies page buffer entries into the VMBus send buffer using phys_to_virt() on the entry PFN. Entries for the RNDIS header and the skb linear data come from kmalloc'd memory and are always in the kernel direct map, but entries for skb fragments reference page cache or user pages, which on 32-bit x86 with CONFIG_HIGHMEM=y can live above the LOWMEM boundary. For such a page phys_to_virt() returns an address outside the direct map and the subsequent memcpy() faults on the transmit softirq path, which is fatal. Map the pages with kmap_local_page() instead, handling two properties of the page buffer entries: - pb[i].pfn is a Hyper-V PFN at HV_HYP_PAGE_SIZE (4K) granularity, not a native PFN. Reconstruct the physical address first and derive the native page from it, so the mapping stays correct where PAGE_SIZE > HV_HYP_PAGE_SIZE (e.g. arm64 with 64K pages). - Since commit 41a6328b2c55 ("hv_netvsc: Preserve contiguous PFN grouping in the page buffer array"), an entry describes a full physically contiguous fragment and pb[i].len can exceed PAGE_SIZE, while kmap_local_page() maps a single page. Copy page by page, splitting at native page boundaries. The copy path only handles packets smaller than the send section size (6144 bytes by default); larger packets take the cp_partial path where only the RNDIS header is copied. So entries here are bounded by the section size and a copy is split at most once on 4K-page systems. On !CONFIG_HIGHMEM configs kmap_local_page() folds to page_address() and no mapping work is added.

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix posix_acl leak on SETACL decode failure nfsaclsvc_decode_setaclargs() and nfs3svc_decode_setaclargs() each call nfs_stream_decode_acl() twice, first for NFS_ACL and then for NFS_DFACL. Each successful call transfers ownership of a freshly allocated posix_acl into argp->acl_access or argp->acl_default. If the first call succeeds but the second fails, the decoder returns false and argp->acl_access is left dangling. ACLPROC2_SETACL.pc_release was wired to nfssvc_release_attrstat and ACLPROC3_SETACL.pc_release was wired to nfs3svc_release_fhandle. Both only call fh_put() and have no knowledge of the ACL fields on argp. The posix_acl_release() pairs sat at the out: labels inside nfsacld_proc_setacl() and nfsd3_proc_setacl(), but svc_process() skips pc_func when pc_decode returns false, so that cleanup is unreachable on decode failure: svc_process_common() pc_decode() /* decode_setaclargs: false */ /* pc_func skipped */ pc_release() /* fh_put only -- ACLs leaked */ The orphaned posix_acl is leaked for the lifetime of the server. Fix by adding nfsaclsvc_release_setacl() and nfs3svc_release_setacl(), which release both argp->acl_access and argp->acl_default in addition to fh_put(), and wiring them as pc_release for their respective SETACL procedures. pc_release runs on every path svc_process() takes after decode, including decode failure, so the posix_acl_release() pairs are removed from the proc functions' out: labels to keep ownership in one place. This matches the existing release_getacl() pattern used by the sibling GETACL procedures.

In the Linux kernel, the following vulnerability has been resolved: pppoe: drop PFC frames RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT RECOMMENDED for PPPoE. In practice, pppd does not support negotiating PFC for PPPoE sessions, and the current PPPoE driver assumes an uncompressed (2-byte) protocol field. However, the generic PPP layer function ppp_input() is not aware of the negotiation result, and still accepts PFC frames. If a peer with a broken implementation or an attacker sends a frame with a compressed (1-byte) protocol field, the subsequent PPP payload is shifted by one byte. This causes the network header to be 4-byte misaligned, which may trigger unaligned access exceptions on some architectures. To reduce the attack surface, drop PPPoE PFC frames. Introduce ppp_skb_is_compressed_proto() helper function to be used in both ppp_generic.c and pppoe.c to avoid open-coding.

In the Linux kernel, the following vulnerability has been resolved: net: tls: fix strparser anchor skb leak on offload RX setup failure When tls_set_device_offload_rx() fails at tls_dev_add(), the error path calls tls_sw_free_resources_rx() to clean up the SW context that was initialized by tls_set_sw_offload(). This function calls tls_sw_release_resources_rx() (which stops the strparser via tls_strp_stop()) and tls_sw_free_ctx_rx() (which kfrees the context), but never frees the anchor skb that was allocated by alloc_skb(0) in tls_strp_init(). Note that tls_sw_free_resources_rx() is exclusively used for this "failed to start offload" code path, there's no other caller. The leak did not exist before commit 84c61fe1a75b ("tls: rx: do not use the standard strparser"), because the standard strparser doesn't try to pre-allocate an skb. The normal close path in tls_sk_proto_close() handles cleanup by calling tls_sw_strparser_done() (which calls tls_strp_done()) after dropping the socket lock, because tls_strp_done() does cancel_work_sync() and the strparser work handler takes the socket lock.

In the Linux kernel, the following vulnerability has been resolved: NFSD: fix nfs4_file access extra count in nfsd4_add_rdaccess_to_wrdeleg In nfsd4_add_rdaccess_to_wrdeleg, if fp->fi_fds[O_RDONLY] is already set by another thread, __nfs4_file_get_access should not be called to increment the nfs4_file access count since that was already done by the thread that added READ access to the file. The extra fi_access count in nfs4_file can prevent the corresponding nfsd_file from being freed. When stopping nfs-server service, these extra access counts trigger a BUG in kmem_cache_destroy() that shows nfsd_file object remaining on __kmem_cache_shutdown. This problem can be reproduced by running the Git project's test suite over NFS.

In the Linux kernel, the following vulnerability has been resolved: netfilter: nfnetlink_osf: fix potential NULL dereference in ttl check The nf_osf_ttl() function accessed skb->dev to perform a local interface address lookup without verifying that the device pointer was valid. Additionally, the implementation utilized an in_dev_for_each_ifa_rcu loop to match the packet source address against local interface addresses. It assumed that packets from the same subnet should not see a decrement on the initial TTL. A packet might appear it is from the same subnet but it actually isn't especially in modern environments with containers and virtual switching. Remove the device dereference and interface loop. Replace the logic with a switch statement that evaluates the TTL according to the ttl_check.

In the Linux kernel, the following vulnerability has been resolved: nfsd: fix dead ACL conflict guard in nfsd4_create nfsd4_create() steals create->cr_dpacl/cr_pacl into the local nfsd_attrs via the designated initializer, then immediately sets the source pointers to NULL. The subsequent conflict guard tests the already-nilled source fields, making it permanently dead code: if (create->cr_acl) { if (create->cr_dpacl || create->cr_pacl) /* always false */ When a client encodes both FATTR4_WORD0_ACL and FATTR4_WORD2_POSIX_{DEFAULT,ACCESS}_ACL in the same CREATE fattr bitmap, nfsd4_acl_to_attr() overwrites attrs.na_pacl/na_dpacl without releasing the originals, leaking two posix_acl slab objects per request. Repeated requests cause unbounded slab exhaustion. Fix by checking attrs.na_dpacl/na_pacl (the stolen values) instead of the nilled create->cr_dpacl/cr_pacl, matching the correct pattern already used in nfsd4_setattr().

In the Linux kernel, the following vulnerability has been resolved: NFSv4/pNFS: reject zero-length r_addr in nfs4_decode_mp_ds_addr nfs4_decode_mp_ds_addr() decodes the r_netid and r_addr opaques of a netaddr4 from a GETDEVICEINFO multipath-DS body, then immediately calls strrchr(buf, '.') to locate the port separator. Both decodes use xdr_stream_decode_string_dup(), and the current code checks only "nlen < 0" / "rlen < 0" before dereferencing the returned string. When the on-wire opaque has length zero, xdr_stream_decode_opaque_inline() returns 0 and xdr_stream_decode_string_dup() falls through to its "*str = NULL; return ret" tail, leaving buf NULL with a return value of 0. The "< 0" check does not catch this, and the next line is strrchr(NULL, '.'), a kernel NULL pointer dereference reachable from any pNFS-flexfile client mounted against a malicious or compromised metadata server. Reject the zero-length cases explicitly so the decoder fails with -EBADMSG (treated as a malformed GETDEVICEINFO body) instead of panicking the client.

In the Linux kernel, the following vulnerability has been resolved: net: bcmgenet: fix leaking free_bds While reclaiming the tx queue we fast forward the write pointer to drop any data in flight. These dropped frames are not added back to the pool of free bds. We also need to tell the netdev that we are dropping said data.

In the Linux kernel, the following vulnerability has been resolved: libceph: handle rbtree insertion error in decode_choose_args() A message of type CEPH_MSG_OSD_MAP contains an OSD map that itself contains a CRUSH map. The received CRUSH map may optionally contain choose_args that get decoded in decode_choose_args(). In this function, num_choose_arg_maps is read from the message, and a corresponding number of crush_choose_arg_maps gets decoded afterwards. Each crush_choose_arg_map has a choose_args_index, which serves as the key when inserting it into the choose_args rbtree of the decoded crush_map. If a (potentially corrupted) message contains two crush_choose_arg_maps with the same index, the assertion in insert_choose_arg_map() triggers a kernel BUG when trying to insert the second crush_choose_arg_map. This patch fixes the issue by switching to the non-asserting rbtree insertion function and rejecting the message if the insertion fails. [ idryomov: changelog ]

In the Linux kernel, the following vulnerability has been resolved: sctp: stream: fully roll back denied add-stream state When ADD_OUT_STREAMS is denied, SCTP only shrinks the queued chunks and then lowers outcnt. That leaves removed stream metadata behind, so a later re-add can reuse a stale ext and hit a null-pointer dereference in the scheduler get path. Fix the rollback by tearing down the removed stream state the same way other stream resizes do. Unschedule the current scheduler state, drop the removed stream ext state with sctp_stream_outq_migrate(), and then reschedule the remaining streams. This keeps scheduler-private RR/FC/PRIO lists consistent while fully rolling back denied outgoing stream additions.

In the Linux kernel, the following vulnerability has been resolved: libceph: Fix potential null-ptr-deref in decode_choose_args() A message of type CEPH_MSG_OSD_MAP contains an OSD map that itself contains a CRUSH map. When decoding this CRUSH map in crush_decode(), an array of max_buckets CRUSH buckets is decoded, where some indices may not refer to actual buckets and are therefore set to NULL. The received CRUSH map may optionally contain choose_args that get decoded in decode_choose_args(). When decoding a crush_choose_arg_map, a series of choose_args for different buckets is decoded, with the bucket_index being read from the incoming message. It is only checked that the bucket index does not exceed max_buckets, but not that it doesn't point to an index with a NULL bucket. If a (potentially corrupted) message contains a crush_choose_arg_map including such a bucket_index, a null pointer dereference may occur in the subsequent processing when attempting to access the bucket with the given index. This patch fixes the issue by extending the affected check. Now, it is only attempted to access the bucket if it is not NULL.

In the Linux kernel, the following vulnerability has been resolved: ceph: put folios not suitable for writeback The batch holds references to the folios (see `filemap_get_folios`, `folio_batch_release`), so we need to `folio_put` the folios we remove. Tested on v6.18.

IBM DB2 for Linux, UNIX and Windows (includes Db2 Connect Server) 10.5, 11.1, and 11.5 is vulnerable to a denial of service as it may trap when compiling a variation of an anonymous block. IBM X-Force ID: 251991.

In the Linux kernel, the following vulnerability has been resolved: xfrm: ipcomp: Free destination pages on acomp errors Move the out_free_req label up by a couple of lines so that the allocated dst SG list gets freed on error as well as success.

In the Linux kernel, the following vulnerability has been resolved: batman-adv: dat: handle forward allocation error batadv_dat_forward_data() calls pskb_copy_for_clone() to duplicate an skb for each DHT candidate, but does not check the return value before passing it to batadv_send_skb_prepare_unicast_4addr(). That function dereferences the skb unconditionally, so a failed allocation triggers a NULL pointer dereference. Skip forwarding to the current DHT candidate on allocation failure.

Stack-based buffer overflow in .NET Framework allows an unauthorized attacker to deny service over a network.

Allocation of resources without limits or throttling in .NET allows an unauthorized attacker to deny service over a network.

In the Linux kernel, the following vulnerability has been resolved: libceph: Fix potential out-of-bounds access in __ceph_x_decrypt() In __ceph_x_decrypt(), a part of the buffer p is interpreted as a ceph_x_encrypt_header, and the magic field of this struct is accessed. This happens without any guarantee that the buffer is large enough to hold this struct. The function parameter ciphertext_len represents the length of the ciphertext to decrypt and is guaranteed to be at most the remaining size of the allocated buffer p. However, this value is not necessarily greater than sizeof(ceph_x_encrypt_header). E.g., a message frame of type FRAME_TAG_AUTH_REPLY_MORE, that is just as long to hold the ciphertext at its end with a ciphertext_len of 8 or less, can trigger an out-of-bounds memory access when accessing hdr->magic. This patch fixes the issue by adding a check to ensure that the decrypted plaintext in the buffer is large enough to represent at least the ceph_x_encrypt_header.

Improper validation of specified type of input in .NET Framework allows an unauthorized attacker to deny service over a network.

Allocation of resources without limits or throttling in .NET Framework allows an unauthorized attacker to deny service over a network.

Allocation of resources without limits or throttling in .NET allows an unauthorized attacker to deny service over a network.

In the Linux kernel, the following vulnerability has been resolved: Revert "wireguard: device: enable threaded NAPI" This reverts commit 933466fc50a8e4eb167acbd0d8ec96a078462e9c which is commit db9ae3b6b43c79b1ba87eea849fd65efa05b4b2e upstream. We have had three independent production user reports in combination with Cilium utilizing WireGuard as encryption underneath that k8s Pod E/W traffic to certain peer nodes fully stalled. The situation appears as follows: - Occurs very rarely but at random times under heavy networking load. - Once the issue triggers the decryption side stops working completely for that WireGuard peer, other peers keep working fine. The stall happens also for newly initiated connections towards that particular WireGuard peer. - Only the decryption side is affected, never the encryption side. - Once it triggers, it never recovers and remains in this state, the CPU/mem on that node looks normal, no leak, busy loop or crash. - bpftrace on the affected system shows that wg_prev_queue_enqueue fails, thus the MAX_QUEUED_PACKETS (1024 skbs!) for the peer's rx_queue is reached. - Also, bpftrace shows that wg_packet_rx_poll for that peer is never called again after reaching this state for that peer. For other peers wg_packet_rx_poll does get called normally. - Commit db9ae3b ("wireguard: device: enable threaded NAPI") switched WireGuard to threaded NAPI by default. The default has not been changed for triggering the issue, neither did CPU hotplugging occur (i.e. 5bd8de2 ("wireguard: queueing: always return valid online CPU in wg_cpumask_choose_online()")). - The issue has been observed with stable kernels of v5.15 as well as v6.1. It was reported to us that v5.10 stable is working fine, and no report on v6.6 stable either (somewhat related discussion in [0] though). - In the WireGuard driver the only material difference between v5.10 stable and v5.15 stable is the switch to threaded NAPI by default. [0] https://lore.kernel.org/netdev/CA+wXwBTT74RErDGAnj98PqS=wvdh8eM1pi4q6tTdExtjnokKqA@mail.gmail.com/ Breakdown of the problem: 1) skbs arriving for decryption are enqueued to the peer->rx_queue in wg_packet_consume_data via wg_queue_enqueue_per_device_and_peer. 2) The latter only moves the skb into the MPSC peer queue if it does not surpass MAX_QUEUED_PACKETS (1024) which is kept track in an atomic counter via wg_prev_queue_enqueue. 3) In case enqueueing was successful, the skb is also queued up in the device queue, round-robin picks a next online CPU, and schedules the decryption worker. 4) The wg_packet_decrypt_worker, once scheduled, picks these up from the queue, decrypts the packets and once done calls into wg_queue_enqueue_per_peer_rx. 5) The latter updates the state to PACKET_STATE_CRYPTED on success and calls napi_schedule on the per peer->napi instance. 6) NAPI then polls via wg_packet_rx_poll. wg_prev_queue_peek checks on the peer->rx_queue. It will wg_prev_queue_dequeue if the queue->peeked skb was not cached yet, or just return the latter otherwise. (wg_prev_queue_drop_peeked later clears the cache.) 7) From an ordering perspective, the peer->rx_queue has skbs in order while the device queue with the per-CPU worker threads from a global ordering PoV can finish the decryption and signal the skb PACKET_STATE_CRYPTED out of order. 8) A situation can be observed that the first packet coming in will be stuck waiting for the decryption worker to be scheduled for a longer time when the system is under pressure. 9) While this is the case, the other CPUs in the meantime finish decryption and call into napi_schedule. 10) Now in wg_packet_rx_poll it picks up the first in-order skb from the peer->rx_queue and sees that its state is still PACKET_STATE_UNCRYPTED. The NAPI poll routine then exits e ---truncated---

IBM Db2 for Linux, UNIX and Windows 12.1.0 and 12.1.1 is vulnerable to a denial of service as the server may crash under certain conditions with a specially crafted query.

CAI Content Credentials is affected by an Improper Input Validation vulnerability that could result in an application denial-of-service. An attacker could exploit this vulnerability to crash the application, leading to a denial-of-service condition. Exploitation of this issue does not require user interaction.

In the Linux kernel, the following vulnerability has been resolved: tcp: fix mptcp DSS corruption due to large pmtu xmit Syzkaller was able to trigger a DSS corruption: TCP: request_sock_subflow_v4: Possible SYN flooding on port [::]:20002. Sending cookies. ------------[ cut here ]------------ WARNING: CPU: 0 PID: 5227 at net/mptcp/protocol.c:695 __mptcp_move_skbs_from_subflow+0x20a9/0x21f0 net/mptcp/protocol.c:695 Modules linked in: CPU: 0 UID: 0 PID: 5227 Comm: syz-executor350 Not tainted 6.11.0-syzkaller-08829-gaf9c191ac2a0 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 08/06/2024 RIP: 0010:__mptcp_move_skbs_from_subflow+0x20a9/0x21f0 net/mptcp/protocol.c:695 Code: 0f b6 dc 31 ff 89 de e8 b5 dd ea f5 89 d8 48 81 c4 50 01 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc e8 98 da ea f5 90 <0f> 0b 90 e9 47 ff ff ff e8 8a da ea f5 90 0f 0b 90 e9 99 e0 ff ff RSP: 0018:ffffc90000006db8 EFLAGS: 00010246 RAX: ffffffff8ba9df18 RBX: 00000000000055f0 RCX: ffff888030023c00 RDX: 0000000000000100 RSI: 00000000000081e5 RDI: 00000000000055f0 RBP: 1ffff110062bf1ae R08: ffffffff8ba9cf12 R09: 1ffff110062bf1b8 R10: dffffc0000000000 R11: ffffed10062bf1b9 R12: 0000000000000000 R13: dffffc0000000000 R14: 00000000700cec61 R15: 00000000000081e5 FS: 000055556679c380(0000) GS:ffff8880b8600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020287000 CR3: 0000000077892000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <IRQ> move_skbs_to_msk net/mptcp/protocol.c:811 [inline] mptcp_data_ready+0x29c/0xa90 net/mptcp/protocol.c:854 subflow_data_ready+0x34a/0x920 net/mptcp/subflow.c:1490 tcp_data_queue+0x20fd/0x76c0 net/ipv4/tcp_input.c:5283 tcp_rcv_established+0xfba/0x2020 net/ipv4/tcp_input.c:6237 tcp_v4_do_rcv+0x96d/0xc70 net/ipv4/tcp_ipv4.c:1915 tcp_v4_rcv+0x2dc0/0x37f0 net/ipv4/tcp_ipv4.c:2350 ip_protocol_deliver_rcu+0x22e/0x440 net/ipv4/ip_input.c:205 ip_local_deliver_finish+0x341/0x5f0 net/ipv4/ip_input.c:233 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 __netif_receive_skb_one_core net/core/dev.c:5662 [inline] __netif_receive_skb+0x2bf/0x650 net/core/dev.c:5775 process_backlog+0x662/0x15b0 net/core/dev.c:6107 __napi_poll+0xcb/0x490 net/core/dev.c:6771 napi_poll net/core/dev.c:6840 [inline] net_rx_action+0x89b/0x1240 net/core/dev.c:6962 handle_softirqs+0x2c5/0x980 kernel/softirq.c:554 do_softirq+0x11b/0x1e0 kernel/softirq.c:455 </IRQ> <TASK> __local_bh_enable_ip+0x1bb/0x200 kernel/softirq.c:382 local_bh_enable include/linux/bottom_half.h:33 [inline] rcu_read_unlock_bh include/linux/rcupdate.h:919 [inline] __dev_queue_xmit+0x1764/0x3e80 net/core/dev.c:4451 dev_queue_xmit include/linux/netdevice.h:3094 [inline] neigh_hh_output include/net/neighbour.h:526 [inline] neigh_output include/net/neighbour.h:540 [inline] ip_finish_output2+0xd41/0x1390 net/ipv4/ip_output.c:236 ip_local_out net/ipv4/ip_output.c:130 [inline] __ip_queue_xmit+0x118c/0x1b80 net/ipv4/ip_output.c:536 __tcp_transmit_skb+0x2544/0x3b30 net/ipv4/tcp_output.c:1466 tcp_transmit_skb net/ipv4/tcp_output.c:1484 [inline] tcp_mtu_probe net/ipv4/tcp_output.c:2547 [inline] tcp_write_xmit+0x641d/0x6bf0 net/ipv4/tcp_output.c:2752 __tcp_push_pending_frames+0x9b/0x360 net/ipv4/tcp_output.c:3015 tcp_push_pending_frames include/net/tcp.h:2107 [inline] tcp_data_snd_check net/ipv4/tcp_input.c:5714 [inline] tcp_rcv_established+0x1026/0x2020 net/ipv4/tcp_input.c:6239 tcp_v4_do_rcv+0x96d/0xc70 net/ipv4/tcp_ipv4.c:1915 sk_backlog_rcv include/net/sock.h:1113 [inline] __release_sock+0x214/0x350 net/core/sock.c:3072 release_sock+0x61/0x1f0 net/core/sock.c:3626 mptcp_push_ ---truncated---

Allocation of resources without limits or throttling in .NET allows an unauthorized attacker to deny service over a network.

In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Reject unknown opcodes before ICRC processing Even after applying commit 7244491dab34 ("RDMA/rxe: Validate pad and ICRC before payload_size() in rxe_rcv"), a single unauthenticated UDP packet can still trigger panic. That patch handled payload_size() underflow only for valid opcodes with short packets, not for packets carrying an unknown opcode. The unknown-opcode OOB read described below predates that commit and reaches back to the initial Soft RoCE driver. The check added there reads pkt->paylen < header_size(pkt) + bth_pad(pkt) + RXE_ICRC_SIZE where header_size(pkt) expands to rxe_opcode[pkt->opcode].length. The rxe_opcode[] array has 256 entries but is only populated for defined IB opcodes; any other entry (for example opcode 0xff) is zero-initialized, so length == 0 and the check degenerates to pkt->paylen < 0 + bth_pad(pkt) + RXE_ICRC_SIZE which does not constrain pkt->paylen enough. rxe_icrc_hdr() then computes rxe_opcode[pkt->opcode].length - RXE_BTH_BYTES which underflows when length == 0 and passes a huge value to rxe_crc32(), causing an out-of-bounds read of the skb payload. Reproduced on v7.0-rc7 with that fix applied, QEMU/KVM with CONFIG_RDMA_RXE=y and CONFIG_KASAN=y, after rdma link add rxe0 type rxe netdev eth0 A single 48-byte UDP packet to port 4791 with BTH opcode=0xff and QPN=IB_MULTICAST_QPN triggers: BUG: KASAN: slab-out-of-bounds in crc32_le+0x115/0x170 Read of size 1 at addr ... The buggy address is located 0 bytes to the right of allocated 704-byte region Call Trace: crc32_le+0x115/0x170 rxe_icrc_hdr.isra.0+0x226/0x300 rxe_icrc_check+0x13f/0x3a0 rxe_rcv+0x6e1/0x16e0 rxe_udp_encap_recv+0x20a/0x320 udp_queue_rcv_one_skb+0x7ed/0x12c0 Subsequent packets with the same shape fault on unmapped memory and panic the kernel. The trigger requires only module load and "rdma link add"; no QP, no connection, and no authentication. Fix this by rejecting packets whose opcode has no rxe_opcode[] entry, detected via the zero mask or zero length, before any length arithmetic runs.

In the Linux kernel, the following vulnerability has been resolved: net: strparser: fix skb_head leak in strp_abort_strp() When the stream parser is aborted, for example after a message assembly timeout, it can still hold a reference to a partially assembled message in strp->skb_head. That skb is not released in strp_abort_strp(), which leaks the partially assembled message and can be triggered repeatedly to exhaust memory. Fix this by freeing strp->skb_head and resetting the parser state in the abort path. Leave strp_stop() unchanged so final cleanup still happens in strp_done() after the work and timer have been synchronized.

In the Linux kernel, the following vulnerability has been resolved: RDMA/hns: Fix WQ_MEM_RECLAIM warning When sunrpc is used, if a reset triggered, our wq may lead the following trace: workqueue: WQ_MEM_RECLAIM xprtiod:xprt_rdma_connect_worker [rpcrdma] is flushing !WQ_MEM_RECLAIM hns_roce_irq_workq:flush_work_handle [hns_roce_hw_v2] WARNING: CPU: 0 PID: 8250 at kernel/workqueue.c:2644 check_flush_dependency+0xe0/0x144 Call trace: check_flush_dependency+0xe0/0x144 start_flush_work.constprop.0+0x1d0/0x2f0 __flush_work.isra.0+0x40/0xb0 flush_work+0x14/0x30 hns_roce_v2_destroy_qp+0xac/0x1e0 [hns_roce_hw_v2] ib_destroy_qp_user+0x9c/0x2b4 rdma_destroy_qp+0x34/0xb0 rpcrdma_ep_destroy+0x28/0xcc [rpcrdma] rpcrdma_ep_put+0x74/0xb4 [rpcrdma] rpcrdma_xprt_disconnect+0x1d8/0x260 [rpcrdma] xprt_rdma_connect_worker+0xc0/0x120 [rpcrdma] process_one_work+0x1cc/0x4d0 worker_thread+0x154/0x414 kthread+0x104/0x144 ret_from_fork+0x10/0x18 Since QP destruction frees memory, this wq should have the WQ_MEM_RECLAIM.

In the Linux kernel, the following vulnerability has been resolved: net/smc: avoid early lgr access in smc_clc_wait_msg A CLC decline can be received while the handshake is still in an early stage, before the connection has been associated with a link group. The decline handling in smc_clc_wait_msg() updates link-group level sync state for first-contact declines, but that state only exists after link group setup has completed. Guard the link-group update accordingly and keep the per-socket peer diagnosis handling unchanged. This preserves the existing sync_err handling for established link-group contexts and avoids touching link-group state before it is available.

In the Linux kernel, the following vulnerability has been resolved: ipmi: Add limits to event and receive message requests The driver would just fetch events and receive messages until the BMC said it was done. To avoid issues with BMCs that never say they are done, add a limit of 10 fetches at a time. In addition, an si interface has an attn state it can return from the hardware which is supposed to cause a flag fetch to see if the driver needs to fetch events or message or a few other things. If the attn bit gets stuck, it's a similar problem. So allow messages in between flag fetches so the driver itself doesn't get stuck. This is a more general fix than the previous fix for the specific bad BMC, but should fix the more general issue of a BMC that won't stop saying it has data. This has been there from the beginning of the driver. It's not a bug per-se, but it is accounting for bugs in BMCs.

In the Linux kernel, the following vulnerability has been resolved: ceph: only d_add() negative dentries when they are unhashed Ceph can call d_add(dentry, NULL) on a negative dentry that is already present in the primary dcache hash. In the current VFS that is not safe. d_add() goes through __d_add() to __d_rehash(), which unconditionally reinserts dentry->d_hash into the hlist_bl bucket. If the dentry is already hashed, reinserting the same node can corrupt the bucket, including creating a self-loop. Once that happens, __d_lookup() can spin forever in the hlist_bl walk, typically looping only on the d_name.hash mismatch check and eventually triggering RCU stall reports like this one: rcu: INFO: rcu_sched self-detected stall on CPU rcu: 87-....: (2100 ticks this GP) idle=3a4c/1/0x4000000000000000 softirq=25003319/25003319 fqs=829 rcu: (t=2101 jiffies g=79058445 q=698988 ncpus=192) CPU: 87 UID: 2952868916 PID: 3933303 Comm: php-cgi8.3 Not tainted 6.18.17-i1-amd #950 NONE Hardware name: Dell Inc. PowerEdge R7615/0G9DHV, BIOS 1.6.6 09/22/2023 RIP: 0010:__d_lookup+0x46/0xb0 Code: c1 e8 07 48 8d 04 c2 48 8b 00 49 89 fc 49 89 f5 48 89 c3 48 83 e3 fe 48 83 f8 01 77 0f eb 2d 0f 1f 44 00 00 48 8b 1b 48 85 db <74> 20 39 6b 18 75 f3 48 8d 7b 78 e8 ba 85 d0 00 4c 39 63 10 74 1f RSP: 0018:ff745a70c8253898 EFLAGS: 00000282 RAX: ff26e470054cb208 RBX: ff26e470054cb208 RCX: 000000006e958966 RDX: ff26e48267340000 RSI: ff745a70c82539b0 RDI: ff26e458f74655c0 RBP: 000000006e958966 R08: 0000000000000180 R09: 9cd08d909b919a89 R10: ff26e458f74655c0 R11: 0000000000000000 R12: ff26e458f74655c0 R13: ff745a70c82539b0 R14: d0d0d0d0d0d0d0d0 R15: 2f2f2f2f2f2f2f2f FS: 00007f5770896980(0000) GS:ff26e482c5d88000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f5764de50c0 CR3: 000000a72abb5001 CR4: 0000000000771ef0 PKRU: 55555554 Call Trace: <TASK> lookup_fast+0x9f/0x100 walk_component+0x1f/0x150 link_path_walk+0x20e/0x3d0 path_lookupat+0x68/0x180 filename_lookup+0xdc/0x1e0 vfs_statx+0x6c/0x140 vfs_fstatat+0x67/0xa0 __do_sys_newfstatat+0x24/0x60 do_syscall_64+0x6a/0x230 entry_SYSCALL_64_after_hwframe+0x76/0x7e This is reachable with reused cached negative dentries. A Ceph lookup or atomic_open can be handed a negative dentry that is already hashed, and fs/ceph/dir.c then hits one of two paths that incorrectly assume "negative" also means "unhashed": - ceph_finish_lookup(): MDS reply is -ENOENT with no trace -> d_add(dentry, NULL) - ceph_lookup(): local ENOENT fast path for a complete directory with shared caps -> d_add(dentry, NULL) Both paths can therefore re-add an already-hashed negative dentry. Ceph already uses the correct pattern elsewhere: ceph_fill_trace() only calls d_add(dn, NULL) for a negative null-dentry reply when d_unhashed(dn) is true. Fix both fs/ceph/dir.c sites the same way: only call d_add() for a negative dentry when it is actually unhashed. If the negative dentry is already hashed, leave it in place and reuse it as-is. This preserves the existing behavior for unhashed dentries while avoiding d_hash list corruption for reused hashed negatives.

In the Linux kernel, the following vulnerability has been resolved: rxrpc: Fix rxkad crypto unalignment handling Fix handling of a packet with a misaligned crypto length. Also handle non-ENOMEM errors from decryption by aborting. Further, remove the WARN_ON_ONCE() so that it can't be remotely triggered (a trace line can still be emitted).

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_conncount: increase the connection clean up limit to 64 After the optimization to only perform one GC per jiffy, a new problem was introduced. If more than 8 new connections are tracked per jiffy the list won't be cleaned up fast enough possibly reaching the limit wrongly. In order to prevent this issue, only skip the GC if it was already triggered during the same jiffy and the increment is lower than the clean up limit. In addition, increase the clean up limit to 64 connections to avoid triggering GC too often and do more effective GCs. This has been tested using a HTTP server and several performance tools while having nft_connlimit/xt_connlimit or OVS limit configured. Output of slowhttptest + OVS limit at 52000 connections: slow HTTP test status on 340th second: initializing: 0 pending: 432 connected: 51998 error: 0 closed: 0 service available: YES

In the Linux kernel, the following vulnerability has been resolved: libceph: Prevent potential null-ptr-deref in ceph_handle_auth_reply() If a message of type CEPH_MSG_AUTH_REPLY contains a zero value for both protocol and result, this is currently not treated as an error. In case of ac->negotiating == true and ac->protocol > 0, this leads to setting ac->protocol = 0 and ac->ops = NULL. Thereafter, the check for ac->protocol != protocol returns false, and init_protocol() is not called. Subsequently, ac->ops->handle_reply() is called, which leads to a null pointer dereference, because ac->ops is still NULL. This patch changes the check for ac->protocol != protocol to !ac->protocol, as this also includes the case when the protocol was set to zero in the message. This causes the message to be treated as containing a bad auth protocol.

In the Linux kernel, the following vulnerability has been resolved: flow_dissector: do not dissect PPPoE PFC frames RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT RECOMMENDED for PPPoE. In practice, pppd does not support negotiating PFC for PPPoE sessions, and the flow dissector driver has assumed an uncompressed frame until the blamed commit. During the review process of that commit [1], support for PFC is suggested. However, having a compressed (1-byte) protocol field means the subsequent PPP payload is shifted by one byte, causing 4-byte misalignment for the network header and an unaligned access exception on some architectures. The exception can be reproduced by sending a PPPoE PFC frame to an ethernet interface of a MIPS board, with RPS enabled, even if no PPPoE session is active on that interface: $ 0 : 00000000 80c40000 00000000 85144817 $ 4 : 00000008 00000100 80a75758 81dc9bb8 $ 8 : 00000010 8087ae2c 0000003d 00000000 $12 : 000000e0 00000039 00000000 00000000 $16 : 85043240 80a75758 81dc9bb8 00006488 $20 : 0000002f 00000007 85144810 80a70000 $24 : 81d1bda0 00000000 $28 : 81dc8000 81dc9aa8 00000000 805ead08 Hi : 00009d51 Lo : 2163358a epc : 805e91f0 __skb_flow_dissect+0x1b0/0x1b50 ra : 805ead08 __skb_get_hash_net+0x74/0x12c Status: 11000403 KERNEL EXL IE Cause : 40800010 (ExcCode 04) BadVA : 85144817 PrId : 0001992f (MIPS 1004Kc) Call Trace: [<805e91f0>] __skb_flow_dissect+0x1b0/0x1b50 [<805ead08>] __skb_get_hash_net+0x74/0x12c [<805ef330>] get_rps_cpu+0x1b8/0x3fc [<805fca70>] netif_receive_skb_list_internal+0x324/0x364 [<805fd120>] napi_complete_done+0x68/0x2a4 [<8058de5c>] mtk_napi_rx+0x228/0xfec [<805fd398>] __napi_poll+0x3c/0x1c4 [<805fd754>] napi_threaded_poll_loop+0x234/0x29c [<805fd848>] napi_threaded_poll+0x8c/0xb0 [<80053544>] kthread+0x104/0x12c [<80002bd8>] ret_from_kernel_thread+0x14/0x1c Code: 02d51821 1060045b 00000000 <8c640000> 3084000f 2c820005 144001a2 00042080 8e220000 To reduce the attack surface and maintain performance, do not process PPPoE PFC frames. [1] https://lore.kernel.org/r/20220630231016.GA392@debian.home

In the Linux kernel, the following vulnerability has been resolved: netfilter: nfnetlink_queue: do shared-unconfirmed check before segmentation Ulrich reports a regression with nfqueue: If an application did not set the 'F_GSO' capability flag and a gso packet with an unconfirmed nf_conn entry is received all packets are now dropped instead of queued, because the check happens after skb_gso_segment(). In that case, we did have exclusive ownership of the skb and its associated conntrack entry. The elevated use count is due to skb_clone happening via skb_gso_segment(). Move the check so that its peformed vs. the aggregated packet. Then, annotate the individual segments except the first one so we can do a 2nd check at reinject time. For the normal case, where userspace does in-order reinjects, this avoids packet drops: first reinjected segment continues traversal and confirms entry, remaining segments observe the confirmed entry. While at it, simplify nf_ct_drop_unconfirmed(): We only care about unconfirmed entries with a refcnt > 1, there is no need to special-case dying entries. This only happens with UDP. With TCP, the only unconfirmed packet will be the TCP SYN, those aren't aggregated by GRO. Next patch adds a udpgro test case to cover this scenario.

.NET and Visual Studio Denial of Service Vulnerability

Uncontrolled resource consumption in ASP.NET Core allows an unauthorized attacker to deny service over a network.

.NET, .NET Framework, and Visual Studio Denial of Service Vulnerability

IBM TXSeries for Multiplatforms 10.1 is vulnerable to a denial of service, caused by improper enforcement of the timeout on individual read operations. By conducting a slowloris-type attacks, a remote attacker could exploit this vulnerability to cause a denial of service.

IBM Engineering Lifecycle Optimization - Publishing 7.0.2 and 7.0.3 could allow a remote attacker to cause a denial of service using a complex regular expression.

IBM TXSeries for Multiplatforms 10.1 could allow a remote attacker to cause a denial of service using persistent connections due to improper allocation of resources.

In the Linux kernel, the following vulnerability has been resolved: RDMA/siw: Fix potential NULL pointer dereference in header processing If siw_get_hdr() returns -EINVAL before set_rx_fpdu_context(), qp->rx_fpdu can be NULL. The error path in siw_tcp_rx_data() dereferences qp->rx_fpdu->more_ddp_segs without checking, which may lead to a NULL pointer deref. Only check more_ddp_segs when rx_fpdu is present. KASAN splat: [ 101.384271] KASAN: null-ptr-deref in range [0x00000000000000c0-0x00000000000000c7] [ 101.385869] RIP: 0010:siw_tcp_rx_data+0x13ad/0x1e50

In the Linux kernel, the following vulnerability has been resolved: net: bonding: Fix nd_tbl NULL dereference when IPv6 is disabled When booting with the 'ipv6.disable=1' parameter, the nd_tbl is never initialized because inet6_init() exits before ndisc_init() is called which initializes it. If bonding ARP/NS validation is enabled, an IPv6 NS/NA packet received on a slave can reach bond_validate_na(), which calls bond_has_this_ip6(). That path calls ipv6_chk_addr() and can crash in __ipv6_chk_addr_and_flags(). BUG: kernel NULL pointer dereference, address: 00000000000005d8 Oops: Oops: 0000 [#1] SMP NOPTI RIP: 0010:__ipv6_chk_addr_and_flags+0x69/0x170 Call Trace: <IRQ> ipv6_chk_addr+0x1f/0x30 bond_validate_na+0x12e/0x1d0 [bonding] ? __pfx_bond_handle_frame+0x10/0x10 [bonding] bond_rcv_validate+0x1a0/0x450 [bonding] bond_handle_frame+0x5e/0x290 [bonding] ? srso_alias_return_thunk+0x5/0xfbef5 __netif_receive_skb_core.constprop.0+0x3e8/0xe50 ? srso_alias_return_thunk+0x5/0xfbef5 ? update_cfs_rq_load_avg+0x1a/0x240 ? srso_alias_return_thunk+0x5/0xfbef5 ? __enqueue_entity+0x5e/0x240 __netif_receive_skb_one_core+0x39/0xa0 process_backlog+0x9c/0x150 __napi_poll+0x30/0x200 ? srso_alias_return_thunk+0x5/0xfbef5 net_rx_action+0x338/0x3b0 handle_softirqs+0xc9/0x2a0 do_softirq+0x42/0x60 </IRQ> <TASK> __local_bh_enable_ip+0x62/0x70 __dev_queue_xmit+0x2d3/0x1000 ? srso_alias_return_thunk+0x5/0xfbef5 ? srso_alias_return_thunk+0x5/0xfbef5 ? packet_parse_headers+0x10a/0x1a0 packet_sendmsg+0x10da/0x1700 ? kick_pool+0x5f/0x140 ? srso_alias_return_thunk+0x5/0xfbef5 ? __queue_work+0x12d/0x4f0 __sys_sendto+0x1f3/0x220 __x64_sys_sendto+0x24/0x30 do_syscall_64+0x101/0xf80 ? exc_page_fault+0x6e/0x170 ? srso_alias_return_thunk+0x5/0xfbef5 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> Fix this by checking ipv6_mod_enabled() before dispatching IPv6 packets to bond_na_rcv(). If IPv6 is disabled, return early from bond_rcv_validate() and avoid the path to ipv6_chk_addr().

In the Linux kernel, the following vulnerability has been resolved: xprtrdma: Decrement re_receiving on the early exit paths In the event that rpcrdma_post_recvs() fails to create a work request (due to memory allocation failure, say) or otherwise exits early, we should decrement ep->re_receiving before returning. Otherwise we will hang in rpcrdma_xprt_drain() as re_receiving will never reach zero and the completion will never be triggered. On a system with high memory pressure, this can appear as the following hung task: INFO: task kworker/u385:17:8393 blocked for more than 122 seconds. Tainted: G S E 6.19.0 #3 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u385:17 state:D stack:0 pid:8393 tgid:8393 ppid:2 task_flags:0x4248060 flags:0x00080000 Workqueue: xprtiod xprt_autoclose [sunrpc] Call Trace: <TASK> __schedule+0x48b/0x18b0 ? ib_post_send_mad+0x247/0xae0 [ib_core] schedule+0x27/0xf0 schedule_timeout+0x104/0x110 __wait_for_common+0x98/0x180 ? __pfx_schedule_timeout+0x10/0x10 wait_for_completion+0x24/0x40 rpcrdma_xprt_disconnect+0x444/0x460 [rpcrdma] xprt_rdma_close+0x12/0x40 [rpcrdma] xprt_autoclose+0x5f/0x120 [sunrpc] process_one_work+0x191/0x3e0 worker_thread+0x2e3/0x420 ? __pfx_worker_thread+0x10/0x10 kthread+0x10d/0x230 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x273/0x2b0 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: RX, Fix XDP multi-buf frag counting for legacy RQ XDP multi-buf programs can modify the layout of the XDP buffer when the program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The referenced commit in the fixes tag corrected the assumption in the mlx5 driver that the XDP buffer layout doesn't change during a program execution. However, this fix introduced another issue: the dropped fragments still need to be counted on the driver side to avoid page fragment reference counting issues. Such issue can be observed with the test_xdp_native_adjst_tail_shrnk_data selftest when using a payload of 3600 and shrinking by 256 bytes (an upcoming selftest patch): the last fragment gets released by the XDP code but doesn't get tracked by the driver. This results in a negative pp_ref_count during page release and the following splat: WARNING: include/net/page_pool/helpers.h:297 at mlx5e_page_release_fragmented.isra.0+0x4a/0x50 [mlx5_core], CPU#12: ip/3137 Modules linked in: [...] CPU: 12 UID: 0 PID: 3137 Comm: ip Not tainted 6.19.0-rc3+ #12 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5e_page_release_fragmented.isra.0+0x4a/0x50 [mlx5_core] [...] Call Trace: <TASK> mlx5e_dealloc_rx_wqe+0xcb/0x1a0 [mlx5_core] mlx5e_free_rx_descs+0x7f/0x110 [mlx5_core] mlx5e_close_rq+0x50/0x60 [mlx5_core] mlx5e_close_queues+0x36/0x2c0 [mlx5_core] mlx5e_close_channel+0x1c/0x50 [mlx5_core] mlx5e_close_channels+0x45/0x80 [mlx5_core] mlx5e_safe_switch_params+0x1a5/0x230 [mlx5_core] mlx5e_change_mtu+0xf3/0x2f0 [mlx5_core] netif_set_mtu_ext+0xf1/0x230 do_setlink.isra.0+0x219/0x1180 rtnl_newlink+0x79f/0xb60 rtnetlink_rcv_msg+0x213/0x3a0 netlink_rcv_skb+0x48/0xf0 netlink_unicast+0x24a/0x350 netlink_sendmsg+0x1ee/0x410 __sock_sendmsg+0x38/0x60 ____sys_sendmsg+0x232/0x280 ___sys_sendmsg+0x78/0xb0 __sys_sendmsg+0x5f/0xb0 [...] do_syscall_64+0x57/0xc50 This patch fixes the issue by doing page frag counting on all the original XDP buffer fragments for all relevant XDP actions (XDP_TX , XDP_REDIRECT and XDP_PASS). This is basically reverting to the original counting before the commit in the fixes tag. As frag_page is still pointing to the original tail, the nr_frags parameter to xdp_update_skb_frags_info() needs to be calculated in a different way to reflect the new nr_frags.

NVIDIA Triton Inference Server for Windows and Linux contains a vulnerability where a user could cause an integer overflow or wraparound, leading to a segmentation fault, by providing an invalid request. A successful exploit of this vulnerability might lead to denial of service.

In the Linux kernel, the following vulnerability has been resolved: cppc_cpufreq: Fix possible null pointer dereference cppc_cpufreq_get_rate() and hisi_cppc_cpufreq_get_rate() can be called from different places with various parameters. So cpufreq_cpu_get() can return null as 'policy' in some circumstances. Fix this bug by adding null return check. Found by Linux Verification Center (linuxtesting.org) with SVACE.