An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of adding new port forwarding rules to the device. It seems that the POST parameters passed in this request to set up routes on the device can be set in such a way that would result in passing commands to a "system" API in the function and thus result in command injection on the device. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that recieves the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_43C280in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "ip_address" is extracted at address 0x0043C2F0. The POST parameter "ipaddress" is concatenated at address 0x0043C958 and this is passed to a "system" function at address 0x00437284. This allows an attacker to provide the payload of his/her choice and finally take control of the device.

An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of blocking key words passing in the web traffic to prevent kids from watching content that might be deemed unsafe using the web management interface. It seems that the device does not implement any cross-site scripting protection mechanism which allows an attacker to trick a user who is logged in to the web management interface into executing a stored cross-site scripting payload on the user's browser and execute any action on the device provided by the web management interface.

An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of adding new routes to the device. It seems that the POST parameters passed in this request to set up routes on the device can be set in such a way that would result in overflowing the stack set up and allow an attacker to control the $ra register stored on the stack. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that recieves the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_00420F38 in IDA pro is identified to be receiving the values sent in the POST request. The POST parameter "gateway" allows to overflow the stack and control the $ra register after 1546 characters. The value from this post parameter is then copied on the stack at address 0x00421348 as shown below. This allows an attacker to provide the payload of his/her choice and finally take control of the device.

A vulnerability was detected in Totolink NR1800X 9.1.0u.6279_B20210910. This affects the function sub_41A68C of the file /cgi-bin/cstecgi.cgi. Performing a manipulation of the argument setUssd results in command injection. The attack is possible to be carried out remotely. The exploit is now public and may be used.

A command injection vulnerability in Trend Micro ServerProtect for Linux 3.0 could allow an attacker to execute arbitrary code on an affected system. An attacker must first obtain admin/root privileges on the SPLX console to exploit this vulnerability.

A vulnerability was determined in Tenda HG3 2.0. This vulnerability affects the function formTracert of the file /boaform/formTracert. Executing a manipulation of the argument datasize can lead to command injection. The attack may be performed from remote. The exploit has been publicly disclosed and may be utilized.

An OS command injection vulnerability in the web administration component of Micro Focus Secure Messaging Gateway (SMG) allows a remote attacker authenticated as a privileged user to execute arbitrary OS commands on the SMG server. This can be exploited in conjunction with CVE-2018-12464 to achieve unauthenticated remote code execution. Affects Micro Focus Secure Messaging Gateway versions prior to 471. It does not affect previous versions of the product that used GWAVA product name (i.e. GWAVA 6.5).

This vulnerability allows remote attackers to execute arbitrary code on affected installations of installations of Marvell QConvergeConsole 5.5.0.64. Although authentication is required to exploit this vulnerability, the existing authentication mechanism can be bypassed. The specific flaw exists within the isHPSmartComponent method of the GWTTestServiceImpl class. The issue results from the lack of proper validation of a user-supplied string before using it to execute a system call. An attacker can leverage this vulnerability to execute code in the context of SYSTEM. Was ZDI-CAN-10501.

There is command injection when ddns processes the hostname, which causes the administrator user to obtain the root privilege of the router. This affects Xiaomi router AX1800rom version < 1.0.336 and Xiaomi route RM1800 root version < 1.0.26.

A vulnerability classified as critical was found in D-Link DIR-600L up to 2.07B01. This vulnerability affects the function wake_on_lan. The manipulation of the argument host leads to command injection. The attack can be initiated remotely. This vulnerability only affects products that are no longer supported by the maintainer.

The lack of nested page table protection in the AMD SEV/SEV-ES feature could potentially lead to arbitrary code execution within the guest VM if a malicious administrator has access to compromise the server hypervisor.

There is command injection in the meshd program in the routing system, resulting in command execution under administrator authority on Xiaomi router AX3600 with ROM version =< 1.1.12

A security flaw has been discovered in Tenda HG3 2.0 300003070. This vulnerability affects the function formgponConf of the file /boaform/admin/formgponConf. The manipulation of the argument fmgpon_loid results in os command injection. It is possible to launch the attack remotely. The exploit has been released to the public and may be used for attacks.

The web interface of the Vertiv Avocent UMG-4000 version 4.2.1.19 is vulnerable to command injection because the application incorrectly neutralizes code syntax before executing. Since all commands within the web application are executed as root, this could allow a remote attacker authenticated with an administrator account to execute arbitrary commands as root.

PhoneSystem Terminal in 3CX Phone System (Debian based installation) 16.0.0.1570 allows an authenticated attacker to run arbitrary commands with the phonesystem user privileges because of "<space><space> followed by <shift><enter>" mishandling.

The web-based diagnostics console in Dell EMC iDRAC6 (Monolithic versions prior to 2.91 and Modular all versions) contains a command injection vulnerability. A remote authenticated malicious iDRAC user with access to the diagnostics console could potentially exploit this vulnerability to execute arbitrary commands as root on the affected iDRAC system.

Grandstream GRP261x VoIP phone running firmware version 1.0.3.6 (Base) allows Command Injection as root in its administrative web interface.

Command Injection in EdgeMAX EdgeSwitch prior to 1.8.2 allow an Admin user to execute commands as root.

In Ubiquiti Networks EdgeSwitch X v1.1.0 and prior, a privileged user can execute arbitrary shell commands over the SSH CLI interface. This allows to execute shell commands under the root user.

Command injection vulnerability in login_cgi in GL.iNet GL-AR300M-Lite devices with firmware 2.27 allows remote attackers to execute arbitrary code.

The Untangle NG firewall 14.2.0 is vulnerable to an authenticated command injection when logged in as an admin user.

A vulnerability was detected in Tenda HG3 2.0. The impacted element is an unknown function of the file /boaform/formCountrystr. The manipulation of the argument countrystr results in os command injection. The attack may be performed from remote. The exploit is now public and may be used.

A vulnerability in the vManage web-based UI (Web UI) in the Cisco SD-WAN Solution could allow an authenticated, remote attacker to inject arbitrary commands that are executed with root privileges. The vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by authenticating to the device and submitting crafted input to the vManage Web UI. A successful exploit could allow the attacker to execute commands with root privileges.

A vulnerability in the NX-API feature of Cisco NX-OS Software could allow an authenticated, remote attacker to execute arbitrary commands with root privileges. The vulnerability is due to incorrect input validation of user-supplied data by the NX-API subsystem. An attacker could exploit this vulnerability by sending malicious HTTP or HTTPS packets to the management interface of an affected system that has the NX-API feature enabled. A successful exploit could allow the attacker to perform a command-injection attack and execute arbitrary commands with root privileges. Note: NX-API is disabled by default. MDS 9000 Series Multilayer Switches are affected running software versions prior to 8.1(1b) and 8.2(3). Nexus 3000 Series Switches are affected running software versions prior to 7.0(3)I4(9) and 7.0(3)I7(4). Nexus 3500 Platform Switches are affected running software versions prior to 7.0(3)I7(4). Nexus 2000, 5500, 5600, and 6000 Series Switches are affected running software versions prior to 7.3(4)N1(1). Nexus 9000 Series Switches in Standalone NX-OS Mode are affected running software versions prior to 7.0(3)I4(9) and 7.0(3)I7(4). Nexus 7000 and 7700 Series Switches are affected running software versions prior to 7.3(3)D1(1) and 8.2(3).

There is an OS Command Injection in Nexus Repository Manager <= 2.14.14 (bypass CVE-2019-5475) that could allow an attacker a Remote Code Execution (RCE). All instances using CommandLineExecutor.java with user-supplied data is vulnerable, such as the Yum Configuration Capability.

A vulnerability in the web-based management interface of Cisco Webex Video Mesh could allow an authenticated, remote attacker to execute arbitrary commands on the affected system. The vulnerability is due to improper validation of user-supplied input by the web-based management interface of the affected software. An attacker could exploit this vulnerability by logging in to the web-based management interface with administrative privileges and supplying crafted requests to the application. A successful exploit could allow the attacker to execute arbitrary commands on the underlying Linux operating system with root privileges on a targeted node.

Dell EMC iDRAC7/iDRAC8, versions prior to 2.60.60.60, and iDRAC9 versions prior to 3.21.21.21 contain a command injection vulnerability in the SNMP agent. A remote authenticated malicious iDRAC user with configuration privileges could potentially exploit this vulnerability to execute arbitrary commands on the iDRAC where SNMP alerting is enabled.

An issue was discovered in Softing uaGate (SI, MB, 840D) firmware through 1.71.00.1225. A CGI script is vulnerable to command injection via a maliciously crafted form parameter.

A vulnerability was detected in TRENDnet TEW-800MB 1.0.1.0. Affected by this vulnerability is the function sub_F934  of the file NTPSyncWithHost.cgi. The manipulation results in command injection. The attack may be launched remotely. The exploit is now public and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A security vulnerability has been detected in TRENDnet TEW-800MB 1.0.1.0. Affected is the function do_setWizard_asp of the file /goform/wizardset of the component Management Interface. The manipulation of the argument WizardConfigured leads to command injection. The attack may be initiated remotely. The exploit has been disclosed publicly and may be used. The vendor was contacted early about this disclosure but did not respond in any way.

A security flaw has been discovered in ZSPACE Q2C NAS up to 1.1.0210050. Affected by this vulnerability is the function zfilev2_api.SafeStatus of the file /v2/file/safe/status of the component HTTP POST Request Handler. The manipulation of the argument safe_dir results in command injection. The attack may be performed from remote. The exploit has been released to the public and may be exploited. The vendor was contacted early about this disclosure and confirmed the existence of the vulnerability. A technical fix is planned to be released.

A vulnerability was identified in ZSPACE Q2C NAS up to 1.1.0210050. Affected is the function zfilev2_api.CloseSafe of the file /v2/file/safe/close of the component HTTP POST Request Handler. The manipulation of the argument safe_dir leads to command injection. The attack is possible to be carried out remotely. The exploit is publicly available and might be used. The vendor was contacted early about this disclosure and confirmed the existence of the vulnerability. A technical fix is planned to be released.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the IP Address in Add Gaming Rule.

Centreon 18.x before 18.10.6, 19.x before 19.04.3, and Centreon web before 2.8.29 allows the attacker to execute arbitrary system commands by using the value "init_script"-"Monitoring Engine Binary" in main.get.php to insert a arbitrary command into the database, and execute it by calling the vulnerable page www/include/configuration/configGenerate/xml/generateFiles.php (which passes the inserted value to the database to shell_exec without sanitizing it, allowing one to execute system arbitrary commands).

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication). The command injection exists in the key ip_addr.

A remote arbitrary command execution vulnerability was discovered in Aruba SD-WAN Software and Gateways; Aruba Operating System Software version(s): Prior to 8.6.0.4-2.2.0.6; Prior to 8.7.1.4, 8.6.0.7, 8.5.0.12, 8.3.0.16. Aruba has released patches for Aruba SD-WAN Software and Gateways and ArubaOS that address this security vulnerability.

A vulnerability in the web-based management interface of the Cisco RV110W Wireless-N VPN Firewall, Cisco RV130W Wireless-N Multifunction VPN Router, and Cisco RV215W Wireless-N VPN Router could allow an authenticated, remote attacker to execute arbitrary commands. The vulnerability is due to improper validation of user-supplied input to scripts by the web-based management interface. An attacker could exploit this vulnerability by sending malicious requests to a targeted device. A successful exploit could allow the attacker to execute arbitrary commands with the privileges of the root user.

A vulnerability in the VPN subsystem configuration in the Cisco SD-WAN Solution could allow an authenticated, remote attacker to inject arbitrary commands that are executed with root privileges. The vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by authenticating to the device and submitting crafted input to the affected parameter in a web page. The attacker must be authenticated to access the affected parameter. A successful exploit could allow the attacker to execute commands with root privileges. This vulnerability affects the following Cisco products if they are running a release of the Cisco SD-WAN Solution prior to Release 18.3.0: vBond Orchestrator Software, vEdge 100 Series Routers, vEdge 1000 Series Routers, vEdge 2000 Series Routers, vEdge 5000 Series Routers, vEdge Cloud Router Platform, vManage Network Management Software, vSmart Controller Software. Cisco Bug IDs: CSCvi69808, CSCvi69810, CSCvi69814, CSCvi69822, CSCvi69827, CSCvi69828, CSCvi69836.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the UDP Ports To Open in Add Gaming Rule.

A vulnerability in the CronJob scheduler API of Cisco Digital Network Architecture (DNA) Center could allow an authenticated, remote attacker to perform a command injection attack. The vulnerability is due to incorrect input validation of user-supplied data. An attacker could exploit this vulnerability by sending a malicious packet. A successful exploit could allow the attacker to execute arbitrary commands with root privileges. Cisco Bug IDs: CSCvi42263.

A vulnerability in the web-based UI of Cisco IP Phone 6800, 7800, and 8800 Series with Multiplatform Firmware before 11.2(1) could allow an authenticated, remote attacker to perform a command injection and execute commands with the privileges of the web server. The vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by including arbitrary shell commands in a specific user input field. Cisco Bug IDs: CSCvi51426.

A vulnerability in the web-based management interface of Cisco Integrated Management Controller (IMC) Software could allow an authenticated, remote attacker to inject and execute arbitrary commands with root privileges on an affected device. The vulnerability is due to insufficient validation of command input by the affected software. An attacker could exploit this vulnerability by sending crafted commands to the web-based management interface of the affected software. A successful exploit could allow the attacker to inject and execute arbitrary, system-level commands with root privileges on an affected device.

A vulnerability in the web-based management interface of Cisco Cloud Services Platform 2100 could allow an authenticated, remote attacker to perform command injection. The vulnerability is due to insufficient input validation of command input. An attacker could exploit this vulnerability by sending customized commands to the web-based management interface.

A vulnerability, which was classified as critical, was found in TOTOLINK A3600R 4.1.2cu.5182_B20201102. This affects the function setdeviceName of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument deviceMac/deviceName leads to buffer overflow. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-272595. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

A vulnerability was found in TOTOLINK A3600R 4.1.2cu.5182_B20201102. It has been classified as critical. Affected is the function setLanguageCfg of the file /cgi-bin/cstecgi.cgi. The manipulation of the argument langType leads to buffer overflow. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. VDB-272598 is the identifier assigned to this vulnerability. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides a web user interface that allows a user to manage the device. As a part of the functionality the device firmware file contains a file known as proxy.sh which allows the device to proxy a specific request to and from from another website. This is primarily used as a method of communication between the device and Vera website when the user is logged in to the https://home.getvera.com and allows the device to communicate between the device and website. One of the parameters retrieved by this specific script is "url". This parameter is not sanitized by the script correctly and is passed in a call to "eval" to execute "curl" functionality. This allows an attacker to escape from the executed command and then execute any commands of his/her choice.

In the AMD SEV/SEV-ES feature, memory can be rearranged in the guest address space that is not detected by the attestation mechanism which could be used by a malicious hypervisor to potentially lead to arbitrary code execution within the guest VM if a malicious administrator has access to compromise the server hypervisor.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides a web user interface that allows a user to manage the device. As a part of the functionality the device firmware file contains a file known as relay.sh which allows the device to create relay ports and connect the device to Vera servers. This is primarily used as a method of communication between the device and Vera servers so the devices can be communicated with even when the user is not at home. One of the parameters retrieved by this specific script is "remote_host". This parameter is not sanitized by the script correctly and is passed in a call to "eval" to execute another script where remote_host is concatenated to be passed a parameter to the second script. This allows an attacker to escape from the executed command and then execute any commands of his/her choice.

Huawei iManager NetEco with software V600R008C00 and V600R008C10 has a command injection vulnerability. An authenticated, remote attacker could exploit this vulnerability to send malicious packets to a target device. Successful exploit could enable a low privileged user to execute commands that a high privileged user could execute, causing the files to be tampered with or deleted.