A vulnerability was found in TRENDnet TEW-815DAP 1.0.2.0. It has been classified as critical. This affects the function do_setNTP of the component POST Request Handler. The manipulation of the argument NtpDstStart/NtpDstEnd leads to command injection. It is possible to initiate the attack remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-252123. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication). The command injection exists in the key ip_addr.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the IP Address in Add Gaming Rule.

A vulnerability, which was classified as critical, has been found in TRENDnet TEW-652BRP 3.04B01. This issue affects some unknown processing of the file get_set.ccp of the component Web Management Interface. The manipulation leads to command injection. The attack may be initiated remotely. The exploit has been disclosed to the public and may be used. The associated identifier of this vulnerability is VDB-219935.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the IP Address in Add Virtual Server.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the action set_sta_enrollee_pin_5g and the key wps_sta_enrollee_pin.

TRENDnet TEW-827DRU with firmware up to and including 2.04B03 contains a stack-based buffer overflow while returning an error message to the user about failure to resolve a hostname during a ping or traceroute attempt. This allows an authenticated user to execute arbitrary code. The exploit can be exercised on the local intranet or remotely if remote administration is enabled.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the key passwd in Routing RIP Settings.

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the Private Port in Add Virtual Server.

Buffer overflow in apply.cgi on TRENDnet TEW-632BRP 1.010B32 and TEW-673GRU devices allows attackers to hijack the control flow to any attacker-specified location by crafting a POST request payload (with authentication).

An issue was discovered in TRENDnet TEW-827DRU firmware before 2.05B11. There is a command injection in apply.cgi (exploitable with authentication) via the TCP Ports To Open in Add Gaming Rule.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action auto_up_fw (or auto_up_lp) with a sufficiently long update_file_name key.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action set_sta_enrollee_pin_wifi1 (or set_sta_enrollee_pin_wifi0) with a sufficiently long wps_sta_enrollee_pin key.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action st_dev_connect, st_dev_disconnect, or st_dev_rconnect with a sufficiently long wan_type key.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action wifi_captive_portal_login with a sufficiently long REMOTE_ADDR key.

TRENDnet TEW-827DRU devices through 2.06B04 contain a stack-based buffer overflow in the ssi binary. The overflow allows an authenticated user to execute arbitrary code by POSTing to apply.cgi via the action kick_ban_wifi_mac_allow with a sufficiently long qcawifi.wifi0_vap0.maclist key.

TRENDnet WiFi Baby Cam TV-IP743SIC has a password of admin for the backdoor root account.

TRENDnet TEW-814DAP v1_(FW1.01B01) was discovered to contain a command injection vulnerability via the ipv4_ping, ipv6_ping parameter at /formSystemCheck .

There is a command injection vulnerability in the TRENDnet TEW-827DRU router with firmware version 2.10B01. An attacker can inject commands into the post request parameters usapps.@smb[%d].username in the apply.cgi interface, thereby gaining root shell privileges.

TRENDnet TEW-815DAP 1.0.2.0 is vulnerable to Command Injection via the do_setNTP function. An authenticated attacker with administrator privileges can leverage this vulnerability over the network via a malicious POST request.

A vulnerability was found in TRENDnet TEW-822DRE 1.03B02. It has been declared as critical. This vulnerability affects unknown code of the file /admin_ping.htm of the component POST Request Handler. The manipulation of the argument ipv4_ping/ipv6_ping leads to command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-252124. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

An issue in TRENDnet TEW-822DRE v.1.03B02 allows a local attacker to execute arbitrary code via the parameters ipv4_ping in the /boafrm/formSystemCheck.

A command injection issue in TRENDnet TEW-411BRPplus v.2.07_eu that allows a local attacker to execute arbitrary code via the data1 parameter in the debug.cgi page.

An issue was discovered on TRENDnet TV-IP1314PI 5.5.3 200714 devices. Command injection can occur because the system function is used by davinci to unpack language packs without strict filtering of URL strings.

TRENDnet TEW-632BRP v1.010B31 devices have an OS command injection vulnerability in the CGl interface "ntp_sync.cgi",which allows remote attackers to execute arbitrary commands via parameter "ntp_server" passed to the "ntp_sync.cgi" binary through a POST request.

A vulnerability has been found in TRENDnet TEW-811DRU 1.0.10.0 and classified as critical. This vulnerability affects unknown code of the component Web Interface. The manipulation leads to command injection. The attack can be initiated remotely. The exploit has been disclosed to the public and may be used. VDB-220018 is the identifier assigned to this vulnerability.

A vulnerability was found in TRENDnet TEW-652BRP 3.04b01. It has been classified as critical. Affected is an unknown function of the file ping.ccp of the component Web Interface. The manipulation leads to command injection. It is possible to launch the attack remotely. The exploit has been disclosed to the public and may be used. The identifier of this vulnerability is VDB-220020.

There is a command injection vulnerability in the TRENDnet TEW-827DRU router with firmware version 2.10B01. An attacker can inject commands into the post request parameters usapps.config.smb_admin_name in the apply.cgi interface, thereby gaining root shell privileges.

An issue was discovered in TRENDnet TEW-824DRU version 1.04b01, allows unauthenticated attackers to execute arbitrary code via the system.ntp.server parameter in the sub_420AE0() function. The attack can be launched remotely.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects GC108P before 1.0.8.2, GC108PP before 1.0.8.2, GS108Tv3 before 7.0.7.2, GS110TPv3 before 7.0.7.2, GS110TPP before 7.0.7.2, GS110TUP before 1.0.5.3, GS710TUP before 1.0.5.3, GS308T before 1.0.3.2, GS310TP before 1.0.3.2, GS710TUP before 1.0.5.3, GS716TP before 1.0.4.2, GS716TPP before 1.0.4.2, GS724TPP before 2.0.6.3, GS724TPv2 before 2.0.6.3, GS724TPP before 2.0.6.3, GS728TPPv2 before 6.0.8.2, GS728TPv2 before 6.0.8.2, GS752TPv2 before 6.0.8.2, GS752TPP before 6.0.8.2, GS750E before 1.0.1.10, MS510TXM before 1.0.4.2, and MS510TXUP before 1.0.4.2.

An issue was discovered on Vera VeraEdge 1.7.19 and Veralite 1.7.481 devices. The device provides a web user interface that allows a user to manage the device. As a part of the functionality the device firmware file contains a file known as relay.sh which allows the device to create relay ports and connect the device to Vera servers. This is primarily used as a method of communication between the device and Vera servers so the devices can be communicated with even when the user is not at home. One of the parameters retrieved by this specific script is "remote_host". This parameter is not sanitized by the script correctly and is passed in a call to "eval" to execute another script where remote_host is concatenated to be passed a parameter to the second script. This allows an attacker to escape from the executed command and then execute any commands of his/her choice.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects CBR40 before 2.5.0.24, CBR750 before 4.6.3.6, RBK852 before 3.2.17.12, RBR850 before 3.2.17.12, and RBS850 before 3.2.17.12.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects R7850 before 1.0.5.74, R7900P before 1.4.2.84, R7960P before 1.4.2.84, R8000 before 1.0.4.74, R8000P before 1.4.2.84, RAX200 before 1.0.4.120, RAX75 before 1.0.4.120, RAX80 before 1.0.4.120, RBK852 before 3.2.17.12, RBR850 before 3.2.17.12, and RBS850 before 3.2.17.12.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects R7850 before 1.0.5.74, R7900P before 1.4.2.84, R7960P before 1.4.2.84, R8000 before 1.0.4.74, R8000P before 1.4.2.84, RAX200 before 1.0.4.120, RAX75 before 1.0.4.120, RAX80 before 1.0.4.120, RBK752 before 3.2.17.12, RBK852 before 3.2.17.12, RBR750 before 3.2.17.12, RBR850 before 3.2.17.12, RBS750 before 3.2.17.12, and RBS850 before 3.2.17.12.

An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of adding new port forwarding rules to the device. It seems that the POST parameters passed in this request to set up routes on the device can be set in such a way that would result in passing commands to a "system" API in the function and thus result in command injection on the device. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that recieves the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_43C280in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "ip_address" is extracted at address 0x0043C2F0. The POST parameter "ipaddress" is concatenated at address 0x0043C958 and this is passed to a "system" function at address 0x00437284. This allows an attacker to provide the payload of his/her choice and finally take control of the device.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects R7000 before 1.0.11.126, R6900P before 1.3.2.126, and R7000P before 1.3.2.126.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects D6200 before 1.1.00.40, D7000 before 1.0.1.78, R6020 before 1.0.0.42, R6080 before 1.0.0.42, R6050 before 1.0.1.26, JR6150 before 1.0.1.26, R6120 before 1.0.0.66, R6220 before 1.1.0.110, R6230 before 1.1.0.110, R6260 before 1.1.0.64, R6800 before 1.2.0.62, R6700v2 before 1.2.0.62, R6900v2 before 1.2.0.62, R7450 before 1.2.0.62, AC2100 before 1.2.0.62, AC2400 before 1.2.0.62, AC2600 before 1.2.0.62, and WNR2020 before 1.1.0.62.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects R7900P before 1.4.2.84, R7960P before 1.4.2.84, and R8000P before 1.4.2.84.

An issue was discovered on Securifi Almond, Almond+, and Almond 2015 devices with firmware AL-R096. The device provides a user with the capability of adding new routes to the device. It seems that the POST parameters passed in this request to set up routes on the device can be set in such a way that would result in passing commands to a "popen" API in the function and thus result in command injection on the device. If the firmware version AL-R096 is dissected using binwalk tool, we obtain a cpio-root archive which contains the filesystem set up on the device that contains all the binaries. The binary "goahead" is the one that has the vulnerable function that receives the values sent by the POST request. If we open this binary in IDA-pro we will notice that this follows a MIPS little endian format. The function sub_00420F38 in IDA pro is identified to be receiving the values sent in the POST request and the value set in POST parameter "dest" is extracted at address 0x00420FC4. The POST parameter "dest is concatenated in a route add command and this is passed to a "popen" function at address 0x00421220. This allows an attacker to provide the payload of his/her choice and finally take control of the device.

NETGEAR D6220 devices before 1.0.0.76 are affected by command injection by an authenticated user.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects AC2100 before 1.2.0.88, AC2400 before 1.2.0.88, AC2600 before 1.2.0.88, D7000 before 1.0.1.82, R6220 before 1.1.0.110, R6230 before 1.1.0.110, R6260 before 1.1.0.84, R6330 before 1.1.0.84, R6350 before 1.1.0.84, R6700v2 before 1.2.0.88, R6800 before 1.2.0.88, R6850 before 1.1.0.84, R6900v2 before 1.2.0.88, R7200 before 1.2.0.88, R7350 before 1.2.0.88, R7400 before 1.2.0.88, and R7450 before 1.2.0.88.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects LBR20 before 2.6.3.50, RBS50Y before 2.7.3.22, RBR10 before 2.7.3.22, RBR20 before 2.7.3.22, RBR40 before 2.7.3.22, RBR50 before 2.7.3.22, RBS10 before 2.7.3.22, RBS20 before 2.7.3.22, RBS40 before 2.7.3.22, RBS50 before 2.7.3.22, RBK12 before 2.7.3.22, RBK20 before 2.7.3.22, RBK40 before 2.7.3.22, and RBK50 before 2.7.3.22.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects R7900 before 1.0.4.38, R7900P before 1.4.2.84, R8000 before 1.0.4.68, R8000P before 1.4.2.84, RAX200 before 1.0.3.106, MR60 before 1.0.6.110, RAX45 before 1.0.2.72, RAX80 before 1.0.3.106, MS60 before 1.0.6.110, RAX50 before 1.0.2.72, RAX75 before 1.0.3.106, RBR750 before 3.2.16.6, RBR850 before 3.2.16.6, RBS750 before 3.2.16.6, RBS850 before 3.2.16.6, RBK752 before 3.2.16.6, and RBK852 before 3.2.16.6.

The Symantec Messaging Gateway before 10.6.3-267 can encounter an issue of remote code execution, which describes a situation whereby an individual may obtain the ability to execute commands remotely on a target machine or in a target process. In this type of occurrence, after gaining access to the system, the attacker may attempt to elevate their privileges.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects D7800 before 1.0.1.60, DM200 before 1.0.0.66, EX2700 before 1.0.1.56, EX6150v2 before 1.0.1.86, EX6200v2 before 1.0.1.86, EX6250 before 1.0.0.128, EX6400 before 1.0.2.144, EX6400v2 before 1.0.0.128, EX6410 before 1.0.0.128, EX6420 before 1.0.0.128, EX7300 before 1.0.2.144, EX7300v2 before 1.0.0.128, EX7320 before 1.0.0.128, R7500v2 before 1.0.3.46, R7800 before 1.0.2.74, R8900 before 1.0.5.26, R9000 before 1.0.5.2, RAX120 before 1.0.1.128, WN3000RPv2 before 1.0.0.78, WN3000RPv3 before 1.0.2.80, WNR2000v5 before 1.0.0.74, XR500 before 2.3.2.66, RBK20 before 2.7.3.22, RBR20 before 2.7.3.22, RBS20 before 2.7.3.22, RBK40 before 2.7.3.22, RBR40 before 2.7.3.22, and RBS40 before 2.7.3.22.

In Sophos Web Appliance (SWA) before 4.3.1.2, a section of the machine's interface responsible for generating reports was vulnerable to remote command injection via the token parameter, aka NSWA-1303.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects CBR40 before 2.5.0.24, CBR750 before 4.6.3.6, RBK852 before 3.2.17.12, RBR850 before 3.2.17.12, and RBS850 before 3.2.17.12.

Certain NETGEAR devices are affected by command injection by an authenticated user. This affects CBR750 before 4.6.3.6, RBK852 before 3.2.17.12, RBR850 before 3.2.17.12, and RBS850 before 3.2.17.12.

A command-injection vulnerability exists in a web application on a custom-built GoAhead web server used on Foscam, Vstarcam, and multiple white-label IP camera models. The mail-sending form in the mail.htm page allows an attacker to inject a command into the receiver1 field in the form; it will be executed with root privileges.

VINGA WR-N300U 77.102.1.4853 is affected by a command execution vulnerability in the goahead component.