Improper neutralization of input during web page generation ('cross-site scripting') vulnerability in ABB T-MAC Plus. This issue affects T-MAC Plus: 4.0-24.

For ABB eSOMS versions 4.0 to 6.0.2, the X-XSS-Protection HTTP response header is not set in responses from the web server. For older web browser not supporting Content Security Policy, this might increase the risk of Cross Site Scripting.

ABB Relion 630 devices 1.1 before 1.1.0.C0, 1.2 before 1.2.0.B3, and 1.3 before 1.3.0.A6 allow remote attackers to cause a denial of service (reboot) via a reboot command in an SPA message.

Improper Input Validation vulnerability in Hitachi ABB Power Grids Relion 670 Series, Relion 670/650 Series, Relion 670/650/SAM600-IO, Relion 650, REB500, RTU500 Series, FOX615 (TEGO1), MSM, GMS600, PWC600 allows an attacker with access to the IEC 61850 network with knowledge of how to reproduce the attack, as well as the IP addresses of the different IEC 61850 access points (of IEDs/products), to force the device to reboot, which renders the device inoperable for approximately 60 seconds. This vulnerability affects only products with IEC 61850 interfaces. This issue affects: Hitachi ABB Power Grids Relion 670 Series 1.1; 1.2.3 versions prior to 1.2.3.20; 2.0 versions prior to 2.0.0.13; 2.1; 2.2.2 versions prior to 2.2.2.3; 2.2.3 versions prior to 2.2.3.2. Hitachi ABB Power Grids Relion 670/650 Series 2.2.0 versions prior to 2.2.0.13. Hitachi ABB Power Grids Relion 670/650/SAM600-IO 2.2.1 versions prior to 2.2.1.6. Hitachi ABB Power Grids Relion 650 1.1; 1.2; 1.3 versions prior to 1.3.0.7. Hitachi ABB Power Grids REB500 7.3; 7.4; 7.5; 7.6; 8.2; 8.3. Hitachi ABB Power Grids RTU500 Series 7.x version 7.x and prior versions; 8.x version 8.x and prior versions; 9.x version 9.x and prior versions; 10.x version 10.x and prior versions; 11.x version 11.x and prior versions; 12.x version 12.x and prior versions. Hitachi ABB Power Grids FOX615 (TEGO1) R1D02 version R1D02 and prior versions. Hitachi ABB Power Grids MSM 2.1.0 versions prior to 2.1.0. Hitachi ABB Power Grids GMS600 1.3.0 version 1.3.0 and prior versions. Hitachi ABB Power Grids PWC600 1.0 versions prior to 1.0.1.4; 1.1 versions prior to 1.1.0.1.

ABB Panel Builder 800 all versions has an improper input validation vulnerability which may allow an attacker to insert and run arbitrary code on a computer where the affected product is used.

Cross Site Scripting vulnerabilities where found providing a potential for malicious scripts to be injected into a client browser.  Affected products: ABB ASPECT - Enterprise v3.08.02; NEXUS Series v3.08.02; MATRIX Series v3.08.02

An attacker could exploit this vulnerability in Hitachi ABB Power Grids Ellipse Enterprise Asset Management (EAM) versions prior to and including 9.0.25 by tricking a user to click on a link containing malicious code that would then be run by the web browser. This can result in the compromise of confidential information, or even the takeover of the user’s session.

An Improper Input Validation issue was discovered in ABB FOX515T release 1.0. An improper input validation vulnerability has been identified, allowing a local attacker to provide a malicious parameter to the script that is not validated by the application, This could enable the attacker to retrieve any file on the server.

An input validation vulnerability exists in the Monitor Pro interface of MicroSCADA Pro and MicroSCADA X SYS600. An authenticated user can launch an administrator level remote code execution irrespective of the authenticated user's role.

An attacker may use a specially crafted message to force Relion 650 series (versions 1.3.0.5 and prior) or Relion 670 series (versions 1.2.3.18, 2.0.0.11, 2.1.0.1 and prior) to reboot, which could cause a denial of service.

For ABB eSOMS versions 4.0 to 6.0.2, the HTTPOnly flag is not set. This can allow Javascript to access the cookie contents, which in turn might enable Cross Site Scripting.

Improper Input Validation vulnerability in the handling of a specially crafted IEC 61850 packet with a valid data item but with incorrect data type in the IEC 61850 OPC Server in the Hitachi Energy MicroSCADA X SYS600, MicroSCADA Pro SYS600. The vulnerability may cause a denial-of-service on the IEC 61850 OPC Server part of the SYS600 product. This issue affects: Hitachi Energy MicroSCADA Pro SYS600 version 9.4 FP2 Hotfix 4 and earlier versions Hitachi Energy MicroSCADA X SYS600 version 10 to version 10.3.1. cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.0:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.1:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.2:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.3:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.4:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.1:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.1.1:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.2:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.2.1:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.3:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.3.1:*:*:*:*:*:*:*

Improper Input Validation vulnerability in the handling of a malformed IEC 104 TCP packet in the Hitachi Energy MicroSCADA X SYS600, MicroSCADA Pro SYS600. Upon receiving a malformed IEC 104 TCP packet, the malformed packet is dropped, however the TCP connection is left open. This may cause a denial-of-service if the affected connection is left open. This issue affects: Hitachi Energy MicroSCADA Pro SYS600 version 9.4 FP2 Hotfix 4 and earlier versions Hitachi Energy MicroSCADA X SYS600 version 10 to version 10.3.1. cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.0:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.1:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.2:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.3:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_pro_sys600:9.4:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.1:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.1.1:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.2:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.2.1:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.3:*:*:*:*:*:*:* cpe:2.3:a:hitachienergy:microscada_x_sys600:10.3.1:*:*:*:*:*:*:*

A vulnerability exists in the HCI IEC 60870-5-104 function included in certain versions of the RTU500 series product. The vulnerability can only be exploited, if the HCI 60870-5-104 is configured with support for IEC 62351-5 and the CMU contains the license feature ‘Advanced security’ which must be ordered separately. If these preconditions are fulfilled, an attacker could exploit the vulnerability by sending a specially crafted message to the RTU500, causing the targeted RTU500 CMU to reboot. The vulnerability is caused by a missing input data validation which eventually if exploited causes an internal buffer to overflow in the HCI IEC 60870-5-104 function.

Improper Input Validation vulnerability in the ABB SPIET800 and PNI800 module allows an attacker to cause the denial of service or make the module unresponsive.

Improper Input Validation vulnerability in ABB 800xA, Control Software for AC 800M, Control Builder Safe, Compact Product Suite - Control and I/O, ABB Base Software for SoftControl allows an attacker to cause the denial of service.

Improper Input Validation vulnerability in the ABB SPIET800 and PNI800 module allows an attacker to cause the denial of service or make the module unresponsive.

Improper Neutralization of Input During Web Page Generation (XSS or 'Cross-site Scripting') vulnerability in ABB EIBPORT V3 KNX, ABB EIBPORT V3 KNX GSM.This issue affects EIBPORT V3 KNX: before 3.9.2; EIBPORT V3 KNX GSM: before 3.9.2.

The installations for ABB System 800xA Information Manager versions 5.1, 6.0 to 6.0.3.2 and 6.1 wrongly contain an auxiliary component. An attacker is able to use this for an XSS-like attack to an authenticated local user, which might lead to execution of arbitrary code.

For the Central Licensing Server component used in ABB products ABB Ability™ System 800xA and related system extensions versions 5.1, 6.0 and 6.1, Compact HMI versions 5.1 and 6.0, Control Builder Safe 1.0, 1.1 and 2.0, Symphony Plus -S+ Operations 3.0 to 3.2 Symphony Plus -S+ Engineering 1.1 to 2.2, Composer Harmony 5.1, 6.0 and 6.1, Melody Composer 5.3, 6.1/6.2 and SPE for Melody 1.0SPx (Composer 6.3), Harmony OPC Server (HAOPC) Standalone 6.0, 6.1 and 7.0, ABB Ability™ System 800xA/ Advant® OCS Control Builder A 1.3 and 1.4, Advant® OCS AC100 OPC Server 5.1, 6.0 and 6.1, Composer CTK 6.1 and 6.2, AdvaBuild 3.7 SP1 and SP2, OPCServer for MOD 300 (non-800xA) 1.4, OPC Data Link 2.1 and 2.2, Knowledge Manager 8.0, 9.0 and 9.1, Manufacturing Operations Management 1812 and 1909, ABB AbilityTM SCADAvantage versions 5.1 to 5.6.5, a weakness in validation of input exists that allows an attacker to block license handling by sending specially crafted messages to the CLS web service.

For the Central Licensing Server component used in ABB products ABB Ability™ System 800xA and related system extensions versions 5.1, 6.0 and 6.1, Compact HMI versions 5.1 and 6.0, Control Builder Safe 1.0, 1.1 and 2.0, Symphony Plus -S+ Operations 3.0 to 3.2 Symphony Plus -S+ Engineering 1.1 to 2.2, Composer Harmony 5.1, 6.0 and 6.1, Melody Composer 5.3, 6.1/6.2 and SPE for Melody 1.0SPx (Composer 6.3), Harmony OPC Server (HAOPC) Standalone 6.0, 6.1 and 7.0, ABB Ability™ System 800xA/ Advant® OCS Control Builder A 1.3 and 1.4, Advant® OCS AC100 OPC Server 5.1, 6.0 and 6.1, Composer CTK 6.1 and 6.2, AdvaBuild 3.7 SP1 and SP2, OPCServer for MOD 300 (non-800xA) 1.4, OPC Data Link 2.1 and 2.2, Knowledge Manager 8.0, 9.0 and 9.1, Manufacturing Operations Management 1812 and 1909, ABB AbilityTM SCADAvantage versions 5.1 to 5.6.5, a weakness in validation of input exists that allows an attacker to alter licenses assigned to the system nodes by sending specially crafted messages to the CLS web service.

A S+ Operations and S+ Historian service is subject to a DoS by special crafted messages. An attacker might use this flaw to make it crash or even execute arbitrary code on the machine where the service is hosted.

A vulnerability in Base Software for SoftControl allows an attacker to insert and run arbitrary code in a computer running the affected product. This issue affects: .

A vulnerability exists in the HCI IEC 60870-5-104 that affects the RTU500 series product versions listed below. Incomplete or wrong received APDU frame layout may cause blocking on link layer. Error reason was an endless blocking when reading incoming frames on link layer with wrong length information of APDU or delayed reception of data octets. Only communication link of affected HCI IEC 60870-5-104 is blocked. If attack sequence stops the communication to the previously attacked link gets normal again.

Due to a lack of file length check, the HMIStudio component of ABB PB610 Panel Builder 600 versions 2.8.0.424 and earlier crashes when trying to load an empty *.JPR application file. An attacker with access to the file system might be able to cause application malfunction such as denial of service.

The HMISimulator component of ABB PB610 Panel Builder 600 versions 2.8.0.424 and earlier fails to validate the content-length field for HTTP requests, exposing HMISimulator to denial of service via crafted HTTP requests manipulating the content-length setting.

Log injection vulnerabilities in ASPECT provide attacker access to inject malicious browser scripts if administrator credentials become compromised.This issue affects ASPECT-Enterprise: through 3.*; NEXUS Series: through 3.*; MATRIX Series: through 3.*.

Stored Cross Site Scripting vulnerabilities exist in ASPECT if administrator creden-tials become compromisedThis issue affects ASPECT-Enterprise: through 3.*; NEXUS Series: through 3.*; MATRIX Series: through 3.*.

A vulnerability exists in the webserver that affects the RTU500 series product versions listed below. A malicious actor could perform cross-site scripting on the webserver due to an RDT language file being improperly sanitized.

A vulnerability exists in the webserver that affects the RTU500 series product versions listed below. A malicious actor could perform cross-site scripting on the webserver due to user input being improperly sanitized.

Improper Input Validation vulnerability in a particular configuration setting field of Hitachi Energy TXpert Hub CoreTec 4 product, allows an attacker with access to an authorized user with ADMIN or ENGINEER role rights to inject an OS command that is executed by the system. This issue affects: Hitachi Energy TXpert Hub CoreTec 4 version 2.0.0; 2.0.1; 2.1.0; 2.1.1; 2.1.2; 2.1.3; 2.2.0; 2.2.1.

Improper Input Validation vulnerability in the APDU parser in the Bidirectional Communication Interface (BCI) IEC 60870-5-104 function of Hitachi Energy RTU500 series allows an attacker to cause the receiving RTU500 CMU of which the BCI is enabled to reboot when receiving a specially crafted message. By default, BCI IEC 60870-5-104 function is disabled (not configured). This issue affects: Hitachi Energy RTU500 series CMU Firmware version 12.0.* (all versions); CMU Firmware version 12.2.* (all versions); CMU Firmware version 12.4.* (all versions).

Cross-site scripting (XSS) vulnerability in the Taxonomy Find module 6.x-2.x through 6.x-1.2 and 7.x-2.x through 7.x-1.0 in Drupal allows remote authenticated users with certain permissions to inject arbitrary web script or HTML via taxonomy vocabulary and term names.

A vulnerability in Veeam ONE allows an unprivileged user who has access to the Veeam ONE Web Client the ability to acquire the NTLM hash of the account used by the Veeam ONE Reporting Service. Note: The criticality of this vulnerability is reduced as it requires interaction by a user with the Veeam ONE Administrator role.

Cross-site scripting (XSS) vulnerability in IBM Rational Collaborative Lifecycle Management (CLM) 3.0.1 before 3.0.1.6 iFix7 Interim Fix 1, 4.0.x before 4.0.7 iFix10, 5.0.x before 5.0.2 iFix15, and 6.0.x before 6.0.1 iFix4; Rational Quality Manager (RQM) 3.0.x before 3.0.1.6 iFix7 Interim Fix 1, 4.0.x before 4.0.7 iFix10, 5.0.x before 5.0.2 iFix15, and 6.0.x before 6.0.1 iFix4; Rational Team Concert (RTC) 3.0.x before 3.0.1.6 iFix7 Interim Fix 1, 4.0.x before 4.0.7 iFix10, 5.0.x before 5.0.2 iFix15, and 6.0.x before 6.0.1 iFix4; Rational Requirements Composer (RRC) 3.0.x before 3.0.1.6 iFix7 Interim Fix 1 and 4.0.x before 4.0.7 iFix10; Rational DOORS Next Generation (RDNG) 4.0.x before 4.0.7 iFix10, 5.0.x before 5.0.2 iFix15, and 6.0.x before 6.0.1 iFix4; Rational Engineering Lifecycle Manager (RELM) 4.0.3, 4.0.4, 4.0.5, 4.0.6, and 4.0.7 before iFix10, 5.0.x before 5.0.2 iFix1, and 6.0.x before 6.0.2; Rational Rhapsody Design Manager (Rhapsody DM) 4.0.x before 4.0.7 iFix10, 5.0.x before 5.0.2 iFix15, and 6.0.x before 6.0.1 iFix4; and Rational Software Architect Design Manager (RSA DM) 4.0.x before 4.0.7 iFix10, 5.0.x before 5.0.2 iFix15, and 6.0.x before 6.0.1 iFix4 allows remote authenticated users with project administrator privileges to inject arbitrary web script or HTML via a crafted project. IBM X-Force ID: 108429.

Svelecte is a flexible autocomplete/select component written in Svelte. Svelecte item names are rendered as raw HTML with no escaping. This allows the injection of arbitrary HTML into the Svelecte dropdown. This can be exploited to execute arbitrary JavaScript whenever a Svelecte dropdown is opened. Item names given to Svelecte appear to be directly rendered as HTML by the default item renderer. This means that any HTML tags in the name are rendered as HTML elements not as text. Note that the custom item renderer shown in https://mskocik.github.io/svelecte/#item-rendering is also vulnerable to the same exploit. Any site that uses Svelecte with dynamically created items either from an external source or from user-created content could be vulnerable to an XSS attack (execution of untrusted JavaScript), clickjacking or any other attack that can be performed with arbitrary HTML injection. The actual impact of this vulnerability for a specific application depends on how trustworthy the sources that provide Svelecte items are and the steps that the application has taken to mitigate XSS attacks. XSS attacks using this vulnerability are mostly mitigated by a Content Security Policy that blocks inline JavaScript. This issue has been addressed in version 3.16.3. Users are advised to upgrade. There are no known workarounds for this vulnerability.

Auth. (contributor+) Stored Cross-Site Scripting (XSS) vulnerability in Artem Abramovich Art Decoration Shortcode plugin <= 1.5.6 versions.

In Splunk Enterprise versions below 9.4.4, 9.3.6 and 9.2.8, and Splunk Cloud Platform versions below 9.3.2411.109, 9.3.2408.119 and 9.2.2406.122, a low-privileged user that does not hold the 'admin' or 'power' Splunk roles could craft a malicious payload through the `dataset.command` parameter of the `/app/search/table` endpoint, which could result in execution of unauthorized JavaScript code in the browser of a user.

Cross-site Scripting (XSS) - Stored in GitHub repository pimcore/pimcore prior to 10.6.4.

Adobe Experience Manager versions 6.5.22 and earlier are affected by a stored Cross-Site Scripting (XSS) vulnerability that could be abused by a low privileged attacker to inject malicious scripts into vulnerable form fields. Malicious JavaScript may be executed in a victim’s browser when they browse to the page containing the vulnerable field.

Cross Site Scripting (XSS) vulnerability in Neos CMS 8.3.3 allows a remote authenticated attacker to execute arbitrary code via a crafted SVG file to the neos/management/media component.

hopetree izone lts c011b48 contains a Cross Site Scripting (XSS) vulnerability in the article comment function. In \apps\comment\views.py, AddCommintView() does not securely filter user input and renders it directly to the frontend page through templates.

In Splunk Enterprise versions below 9.4.4, 9.3.6, and 9.2.8, and Splunk Cloud Platform versions below 9.3.2411.108, 9.3.2408.118 and 9.2.2406.123, a low privileged user that does not hold the admin or power Splunk roles could craft a malicious payload through the error messages and job inspection details of a saved search. This could result in execution of unauthorized JavaScript code in the browser of a user.

A vulnerability was found in Nesote Inout Search Engine AI Edition 1.1. It has been classified as problematic. This affects an unknown part of the file /index.php. The manipulation of the argument page leads to cross site scripting. It is possible to initiate the attack remotely. The associated identifier of this vulnerability is VDB-234231. NOTE: The vendor was contacted early about this disclosure but did not respond in any way.

Cross Site Scripting vulnerability in Chamilo LMS v.1.11.26 allows an attacker to execute arbitrary code via the svkey parameter of the storageapi.php file.

The Domino Catalog template is susceptible to a Stored Cross-Site Scripting (XSS) vulnerability. An attacker with the ability to edit documents in the catalog application/database created from this template can embed a cross site scripting attack. The attack would be activated by an end user clicking it.

Statamic is a flat-first, Laravel and Git powered content management system. Prior to version 4.10.0, the SVG tag does not sanitize malicious SVG. Therefore, an attacker can exploit this vulnerability to perform cross-site scripting attacks using SVG, even when using the `sanitize` function. Version 4.10.0 contains a patch for this issue.

An arbitrary file upload vulnerability in October CMS v3.4.4 allows attackers to execute arbitrary code via a crafted file.

Cross-site scripting (XSS) vulnerability in the Spotlight module 7.x-1.x before 7.x-1.5 for Drupal allows remote authenticated users with certain permissions to inject arbitrary web script or HTML via a node title.

An improper neutralization of input during web page generation vulnerability [CWE-79] in FortiMail version 7.2.0 through 7.2.2 and before 7.0.5 allows an authenticated attacker to inject HTML tags in FortiMail's calendar via input fields.