An Improper Following of Specification by Caller vulnerability in web management (J-Web, Captive Portal, 802.1X, Juniper Secure Connect (JSC) of Juniper Networks Junos OS on SRX Series, EX Series, MX240, MX480, MX960, QFX5120 Series, allows an unauthenticated, network-based attacker, sending genuine traffic targeted to the device to cause the CPU to climb until the device becomes unresponsive. Continuous receipt of these packets will create a sustained Denial of Service (DoS) condition. This issue affects Junos OS:  * All versions before 21.4R3-S9, * from 22.2 before 22.2R3-S5, * from 22.4 before 22.4R3-S4, * from 23.2 before 23.2R2-S3, * from 23.4 before 23.4R2-S3, * from 24.2 before 24.2R1-S1, 24.2R2. An indicator of compromise is to review the CPU % of the httpd process in the CLI: e.g.   show system processes extensive | match httpd  PID nobody       52   0   20M    191M select   2   0:01   80.00% httpd{httpd} <<<<< the percentage of httpd usage if high may be an indicator

An Out-of-bounds Read vulnerability in Juniper Networks Junos OS and Junos OS Evolved's routing protocol daemon (rpd) allows an unauthenticated, network-based attacker to send malformed BGP packets to a device configured with packet receive trace options enabled to crash rpd. This issue affects: Junos OS:  * from 21.2R3-S8 before 21.2R3-S9,  * from 21.4R3-S7 before 21.4R3-S9,  * from 22.2R3-S4 before 22.2R3-S5,  * from 22.3R3-S2 before 22.3R3-S4,  * from 22.4R3 before 22.4R3-S5,  * from 23.2R2 before 23.2R2-S2,  * from 23.4R1 before 23.4R2-S1,  * from 24.2R1 before 24.2R1-S1, 24.2R2. Junos OS Evolved: * from 21.4R3-S7-EVO before 21.4R3-S9-EVO,  * from 22.2R3-S4-EVO before 22.2R3-S5-EVO,  * from 22.3R3-S2-EVO before 22.3R3-S4-EVO,  * from 22.4R3-EVO before 22.4R3-S5-EVO,  * from 23.2R2-EVO before 23.2R2-S2-EVO,  * from 23.4R1-EVO before 23.4R2-S1-EVO,  * from 24.2R1-EVO before 24.2R1-S2-EVO, 24.2R2-EVO. This issue requires a BGP session to be established. This issue can propagate and multiply through multiple ASes until reaching vulnerable devices. This issue affects iBGP and eBGP. This issue affects IPv4 and IPv6. An indicator of compromise may be the presence of malformed update messages in a neighboring AS which is unaffected by this issue: For example, by issuing the command on the neighboring device:  show log messages Reviewing for similar messages from devices within proximity to each other may indicate this malformed packet is propagating:   rpd[<pid>]: Received malformed update from <IP address> (External AS <AS#>) and   rpd[<pid>]: Malformed Attribute

An Uncontrolled Resource Consumption vulnerability in the kernel of Juniper Networks JUNOS OS allows an unauthenticated network based attacker to cause 100% CPU load and the device to become unresponsive by sending a flood of traffic to the out-of-band management ethernet port. Continued receipted of a flood will create a sustained Denial of Service (DoS) condition. Once the flood subsides the system will recover by itself. An indication that the system is affected by this issue would be that kernel and netisr process are shown to be using a lot of CPU cycles like in the following example output: user@host> show system processes extensive ... PID USERNAME PRI NICE SIZE RES STATE C TIME WCPU COMMAND 16 root -72 - 0K 304K WAIT 1 839:40 88.96% intr{swi1: netisr 0} 0 root 97 - 0K 160K RUN 1 732:43 87.99% kernel{bcm560xgmac0 que} This issue affects Juniper Networks JUNOS OS on EX2300 Series, EX3400 Series, and ACX710: All versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2.

In broadband environments, including but not limited to Enhanced Subscriber Management, (CHAP, PPP, DHCP, etc.), on Juniper Networks Junos OS devices where RADIUS servers are configured for managing subscriber access and a subscriber is logged in and then requests to logout, the subscriber may be forced into a "Terminating" state by an attacker who is able to send spoofed messages appearing to originate from trusted RADIUS server(s) destined to the device in response to the subscriber's request. These spoofed messages cause the Junos OS General Authentication Service (authd) daemon to force the broadband subscriber into this "Terminating" state which the subscriber will not recover from thereby causing a Denial of Service (DoS) to the endpoint device. Once in the "Terminating" state, the endpoint subscriber will no longer be able to access the network. Restarting the authd daemon on the Junos OS device will temporarily clear the subscribers out of the "Terminating" state. As long as the attacker continues to send these spoofed packets and subscribers request to be logged out, the subscribers will be returned to the "Terminating" state thereby creating a persistent Denial of Service to the subscriber. An indicator of compromise may be seen by displaying the output of "show subscribers summary". The presence of subscribers in the "Terminating" state may indicate the issue is occurring. This issue affects: Juniper Networks Junos OS 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect: Juniper Networks Junos OS 12.3 version 12.3R1 and later versions; 15.1 version 15.1R1 and later versions.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). When certain specific crafted BGP UPDATE messages are received over an established BGP session, one BGP session may be torn down with an UPDATE message error, or the issue may propagate beyond the local system which will remain non-impacted, but may affect one or more remote systems. This issue is exploitable remotely as the crafted UPDATE message can propagate through unaffected systems and intermediate BGP speakers. Continuous receipt of the crafted BGP UPDATE messages will create a sustained Denial of Service (DoS) condition for impacted devices. This issue affects eBGP and iBGP, in both IPv4 and IPv6 implementations. This issue requires a remote attacker to have at least one established BGP session. Improper Input Validation, Denial of Service vulnerability in Juniper Networks, Inc. Junos OS (BGP, rpd modules), Juniper Networks, Inc. Junos OS Evolved (BGP, rpd modules) allows Fuzzing.This issue affects  Junos OS:  * All versions before 20.4R3-S10, * from 21.1R1 through 21.*, * from 21.2 before 21.2R3-S5, * from 21.3 before 21.3R3-S5, * from 21.4 before 21.4R3-S7 (unaffected from 21.4R3-S5, affected from 21.4R3-S6) * from 22.1 before 22.1R3-S4, * from 22.2 before 22.2R3-S3, * from 22.3 before 22.3R3-S1, * from 22.4 before 22.4R3, * from 23.2 before 23.2R2. Junos OS Evolved: * All versions before 20.4R3-S10-EVO, * from 21.2-EVO before 21.2R3-S7-EVO, * from 21.3-EVO before 21.3R3-S5-EVO, * from 21.4-EVO before 21.4R3-S5-EVO, * from 22.1-EVO before 22.1R3-S4-EVO, * from 22.2-EVO before 22.2R3-S3-EVO, * from 22.3-EVO before 22.3R3-S1-EVO, * from 22.4-EVO before 22.4R3-EVO, * from 23.2-EVO before 23.2R2-EVO.

On Junos devices with the BGP graceful restart helper mode enabled or the BGP graceful restart mechanism enabled, a BGP session restart on a remote peer that has the graceful restart mechanism enabled may cause the local routing protocol daemon (RPD) process to crash and restart. By simulating a specific BGP session restart, an attacker can repeatedly crash the RPD process causing prolonged denial of service (DoS). Graceful restart helper mode for BGP is enabled by default. No other Juniper Networks products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 16.1 versions prior to 16.1R7; 16.1X65 versions prior to 16.1X65-D48; 16.2 versions prior to 16.2R2-S8; 17.1 versions prior to 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S7, 17.2R3; 17.2X75 versions prior to 17.2X75-D92, 17.2X75-D102, 17.2X75-D110; 17.3 versions prior to 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S4, 17.4R2; 18.1 versions prior to 18.1R2. Junos OS releases prior to 16.1R1 are not affected.

On SRX Series devices, a vulnerability in the key-management-daemon (kmd) daemon of Juniper Networks Junos OS allows an attacker to spoof packets targeted to IPSec peers before a security association (SA) is established thereby causing a failure to set up the IPSec channel. Sustained receipt of these spoofed packets can cause a sustained Denial of Service (DoS) condition. This issue affects IPv4 and IPv6 implementations. This issue affects Juniper Networks Junos OS on SRX Series: 12.3X48 versions prior to 12.3X48-D90; 15.1X49 versions prior to 15.1X49-D190; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S9; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R1-S7, 18.3R2-S3, 18.3R3; 18.4 versions prior to 18.4R1-S6, 18.4R2-S3, 18.4R3; 19.1 versions prior to 19.1R1-S4, 19.1R2. This issue does not affect 12.3 or 15.1 releases which are non-SRX Series releases.

On Juniper Networks Junos OS devices, receipt of a malformed IPv6 packet may cause the system to crash and restart (vmcore). This issue can be trigged by a malformed IPv6 packet destined to the Routing Engine. An attacker can repeatedly send the offending packet resulting in an extended Denial of Service condition. Only IPv6 packets can trigger this issue. IPv4 packets cannot trigger this issue. This issue affects Juniper Networks Junos OS 18.4 versions prior to 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S4, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2. This issue does not affect Juniper Networks Junos OS prior to 18.4R1.

When an attacker sends a specific crafted Ethernet Operation, Administration, and Maintenance (Ethernet OAM) packet to a target device, it may improperly handle the incoming malformed data and fail to sanitize this incoming data resulting in an overflow condition. This overflow condition in Juniper Networks Junos OS allows an attacker to cause a Denial of Service (DoS) condition by coring the CFM daemon. Continued receipt of these packets may cause an extended Denial of Service condition. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S15; 12.3X48 versions prior to 12.3X48-D95 on SRX Series; 14.1X50 versions prior to 14.1X50-D145; 14.1X53 versions prior to 14.1X53-D47; 15.1 versions prior to 15.1R2; 15.1X49 versions prior to 15.1X49-D170 on SRX Series; 15.1X53 versions prior to 15.1X53-D67.

On Juniper Networks Junos MX Series with service card configured, receipt of a stream of specific packets may crash the MS-PIC component on MS-MIC or MS-MPC. By continuously sending these specific packets, an attacker can repeatedly bring down MS-PIC on MS-MIC/MS-MPC causing a prolonged Denial of Service. This issue affects MX Series devices using MS-PIC, MS-MIC or MS-MPC service cards with any service configured. This issue affects Juniper Networks Junos OS on MX Series: 17.2R2-S7; 17.3R3-S4, 17.3R3-S5; 17.4R2-S4 and the subsequent SRs (17.4R2-S5, 17.4R2-S6, etc.); 17.4R3; 18.1R3-S3, 18.1R3-S4, 18.1R3-S5, 18.1R3-S6, 18.1R3-S7, 18.1R3-S8; 18.2R3, 18.2R3-S1, 18.2R3-S2; 18.3R2 and the SRs based on 18.3R2; 18.4R2 and the SRs based on 18.4R2; 19.1R1 and the SRs based on 19.1R1; 19.2R1 and the SRs based on 19.2R1; 19.3R1 and the SRs based on 19.3R1.

On Juniper Networks Junos OS devices, a stream of TCP packets sent to the Routing Engine (RE) may cause mbuf leak which can lead to Flexible PIC Concentrator (FPC) crash or the system to crash and restart (vmcore). This issue can be trigged by IPv4 or IPv6 and it is caused only by TCP packets. This issue is not related to any specific configuration and it affects Junos OS releases starting from 17.4R1. However, this issue does not affect Junos OS releases prior to 18.2R1 when Nonstop active routing (NSR) is configured [edit routing-options nonstop-routing]. The number of mbufs is platform dependent. The following command provides the number of mbufs counter that are currently in use and maximum number of mbufs that can be allocated on a platform: user@host> show system buffers 2437/3143/5580 mbufs in use (current/cache/total) Once the device runs out of mbufs, the FPC crashes or the vmcore occurs and the device might become inaccessible requiring a manual restart. This issue affects Juniper Networks Junos OS 17.4 versions prior to 17.4R2-S11, 17.4R3-S2; 18.1 versions prior to 18.1R3-S10; 18.2 versions prior to 18.2R2-S7, 18.2R3-S5; 18.2X75 versions prior to 18.2X75-D41, 18.2X75-D420.12, 18.2X75-D51, 18.2X75-D60, 18.2X75-D34; 18.3 versions prior to 18.3R2-S4, 18.3R3-S2; 18.4 versions prior to 18.4R1-S7, 18.4R2-S4, 18.4R3-S1; 19.1 versions prior to 19.1R1-S5, 19.1R2-S1, 19.1R3; 19.2 versions prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S2, 19.4R2. Versions of Junos OS prior to 17.4R1 are unaffected by this vulnerability.

On Juniper Networks Junos OS and Junos OS Evolved devices, BGP session flapping can lead to a routing process daemon (RPD) crash and restart, limiting the attack surface to configured BGP peers. This issue only affects devices with BGP damping in combination with accepted-prefix-limit configuration. When the issue occurs the following messages will appear in the /var/log/messages: rpd[6046]: %DAEMON-4-BGP_PREFIX_THRESH_EXCEEDED: XXXX (External AS x): Configured maximum accepted prefix-limit threshold(1800) exceeded for inet6-unicast nlri: 1984 (instance master) rpd[6046]: %DAEMON-3-BGP_CEASE_PREFIX_LIMIT_EXCEEDED: 2001:x:x:x::2 (External AS x): Shutting down peer due to exceeding configured maximum accepted prefix-limit(2000) for inet6-unicast nlri: 2001 (instance master) rpd[6046]: %DAEMON-4: bgp_rt_maxprefixes_check_common:9284: NOTIFICATION sent to 2001:x:x:x::2 (External AS x): code 6 (Cease) subcode 1 (Maximum Number of Prefixes Reached) AFI: 2 SAFI: 1 prefix limit 2000 kernel: %KERN-5: mastership_relinquish_on_process_exit: RPD crashed on master RE. Sending SIGUSR2 to chassisd (5612:chassisd) to trigger RE switchover This issue affects: Juniper Networks Junos OS: 17.2R3-S3; 17.3 version 17.3R3-S3 and later versions, prior to 17.3R3-S8; 17.4 version 17.4R2-S4, 17.4R3 and later versions, prior to 17.4R2-S10, 17.4R3-S2; 18.1 version 18.1R3-S6 and later versions, prior to 18.1R3-S10; 18.2 version 18.2R3 and later versions, prior to 18.2R3-S4; 18.2X75 version 18.2X75-D50, 18.2X75-D60 and later versions, prior to 18.2X75-D53, 18.2X75-D65; 18.3 version 18.3R2 and later versions, prior to 18.3R2-S4, 18.3R3-S2; 18.4 version 18.4R2 and later versions, prior to 18.4R2-S5, 18.4R3-S2; 19.1 version 19.1R1 and later versions, prior to 19.1R2-S2, 19.1R3-S1; 19.2 version 19.2R1 and later versions, prior to 19.2R1-S5, 19.2R2; 19.3 versions prior to 19.3R2-S3, 19.3R3; 19.4 versions prior to 19.4R1-S3, 19.4R2; 20.1 versions prior to 20.1R1-S2, 20.1R2. Juniper Networks Junos OS Evolved prior to 20.1R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 17.2R3-S3.

A Missing Release of Memory after Effective Lifetime vulnerability in the Public Key Infrastructure daemon (pkid) of Juniper Networks Junos OS allows an unauthenticated networked attacker to cause Denial of Service (DoS). In a scenario where Public Key Infrastructure (PKI) is used in combination with Certificate Revocation List (CRL), if the CRL fails to download the memory allocated to store the CRL is not released. Repeated occurrences will eventually consume all available memory and lead to an inoperable state of the affected system causing a DoS. This issue affects Juniper Networks Junos OS: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S5; 20.1 versions prior to 20.1R3-S1; 20.2 versions prior to 20.2R3-S2; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. This issue can be observed by monitoring the memory utilization of the pkid process via: root@jtac-srx1500-r2003> show system processes extensive | match pki 20931 root 20 0 733M 14352K select 0:00 0.00% pkid which increases over time: root@jtac-srx1500-r2003> show system processes extensive | match pki 22587 root 20 0 901M 181M select 0:03 0.00% pkid

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to cause a Denial of Service (DoS). The issue is caused by malformed MLD packets looping on a multi-homed Ethernet Segment Identifier (ESI) when VXLAN is configured. These MLD packets received on a multi-homed ESI are sent to the peer, and then incorrectly forwarded out the same ESI, violating the split horizon rule. This issue only affects QFX10K Series switches, including the QFX10002, QFX10008, and QFX10016. Other products and platforms are unaffected by this vulnerability. This issue affects Juniper Networks Junos OS on QFX10K Series: All versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R1-S9, 19.2R3-S5; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S4; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S2; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R2-S1, 21.2R3; 21.3 versions prior to 21.3R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the bbe-smgd of Juniper Networks Junos OS allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). In a Broadband Edge / Subscriber Management scenario on MX Series when a specifically malformed ICMP packet addressed to the device is received from a subscriber the bbe-smgd will crash, affecting the subscriber sessions that are connecting, updating, or terminating. Continued receipt of such packets will lead to a sustained DoS condition. When this issue happens the below log can be seen if the traceoptions for the processes smg-service are enabled: BBE_TRACE(TRACE_LEVEL_INFO, "%s: Dropped unsupported ICMP PKT ... This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S7; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R2; 22.3 versions prior to 22.3R1-S2, 22.3R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the kernel of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to bypass an integrity check. In a 6PE scenario and if an additional integrity check is configured, it will fail to drop specific malformed IPv6 packets, and then these packets will be forwarded to other connected networks. This issue affects Juniper Networks Junos OS: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S7; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R2.

An Unexpected Status Code or Return Value vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated attacker with physical access to the device to cause a Denial of Service (DoS). When certain USB devices are connected to a USB port of the routing-engine (RE), the kernel will crash leading to a reboot of the device. The device will continue to crash as long as the USB device is connected. This issue affects Juniper Networks Junos OS: All versions prior to 19.4R3-S10; 20.2 versions prior to 20.2R3-S7; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R2, 22.2R3; 22.3 versions prior to 22.3R1-S1, 22.3R2; 22.4 versions prior to 22.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability combined with a Race Condition in the flow daemon (flowd) of Juniper Networks Junos OS on SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2 allows an unauthenticated network based attacker sending specific traffic to cause a crash of the flowd/srxpfe process, responsible for traffic forwarding in SRX, which will cause a Denial of Service (DoS). Continued receipt and processing of this specific traffic will create a sustained Denial of Service (DoS) condition. This issue can only occur when specific packets are trying to create the same session and logging for session-close is configured as a policy action. Affected platforms are: SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2. Not affected platforms are: SRX4000 Series, SRX5000 Series with SPC3, and vSRX Series. This issue affects Juniper Networks Junos OS SRX300 Series, SRX500 Series, SRX1500, and SRX5000 Series with SPC2: All versions prior to 17.4R3-S5; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S2; 19.4 versions prior to 19.4R1-S4, 19.4R3-S3; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability combined with Improper Handling of Exceptional Conditions in Juniper Networks Junos OS on QFX Series and PTX Series allows an unauthenticated network based attacker to cause increased FPC CPU utilization by sending specific IP packets which are being VXLAN encapsulated leading to a partial Denial of Service (DoS). Continued receipted of these specific traffic will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on QFX Series: All versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R2-S13, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S7; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R2-S3, 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS on PTX Series: All versions prior to 18.4R3-S9; 19.1 versions prior to 19.1R3-S6; 19.2 versions prior to 19.2R1-S7, 19.2R3-S3; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R3-S5; 20.1 versions prior to 20.1R2-S2, 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R2-S1, 20.3R3; 20.4 versions prior to 20.4R2-S1, 20.4R3; 21.1 versions prior to 21.1R1-S1, 21.1R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved on ACX7000 Series allows an unauthenticated network-based attacker to cause a partial Denial of Service (DoS). On receipt of specific IPv6 transit traffic, Junos OS Evolved on ACX7100-48L, ACX7100-32C and ACX7509 sends this traffic to the Routing Engine (RE) instead of forwarding it, leading to increased CPU utilization of the RE and a partial DoS. This issue only affects systems configured with IPv6. This issue does not affect ACX7024 which is supported from 22.3R1-EVO onwards where the fix has already been incorporated as indicated in the solution section. This issue affects Juniper Networks Junos OS Evolved on ACX7100-48L, ACX7100-32C, ACX7509: 21.1-EVO versions prior to 21.1R3-S2-EVO; 21.2-EVO versions prior to 21.2R3-S2-EVO; 21.3-EVO versions prior to 21.3R3-EVO; 21.4-EVO versions prior to 21.4R1-S1-EVO, 21.4R2-EVO. This issue does not affect Juniper Networks Junos OS Evolved versions prior to 21.1R1-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on EX4k Series and QFX5k Series platforms allows an unauthenticated network-adjacent attacker flapping an interface to cause traffic between VXLAN Network Identifiers (VNIs) to drop, leading to a Denial of Service (DoS). On all EX4k and QFX5k platforms, a link flap in an EVPN-VXLAN configuration Link Aggregation Group (LAG) results in Inter-VNI traffic dropping when there are multiple load-balanced next-hop routes for the same destination. This issue is only applicable to systems that support EVPN-VXLAN Virtual Port-Link Aggregation Groups (VPLAG), such as the QFX5110, QFX5120, QFX5200, EX4100, EX4300, EX4400, and EX4650. Service can only be restored by restarting the affected FPC via the 'request chassis fpc restart slot <slot-number>' command. This issue affects Junos OS on EX4k and QFX5k Series:  * all versions before 21.4R3-S12,  * all versions of 22.2 * from 22.4 before 22.4R3-S8,  * from 23.2 before 23.2R2-S5,  * from 23.4 before 23.4R2-S5,  * from 24.2 before 24.2R2-S3, * from 24.4 before 24.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX4600 and SRX5000 Series allows an unauthenticated and logically adjacent attacker to cause a Denial-of-Service (DoS). If in a multicast scenario a sequence of specific PIM packets is received, this will cause a flowd crash and restart, which leads to momentary service interruption. This issue affects Junos OS on SRX 4600 and SRX 5000 Series: * All versions before 21.4R3-S9, * 22.2 versions before 22.2R3-S5, * 22.3 versions before 22.3R3-S4, * 22.4 versions before 22.4R3-S4, * 23.2 versions before 23.2R2-S2, * 23.4 versions before 23.4R2,  * 24.2 versions before 24.2R1-S1, 24.2R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause an integrity impact to the downstream devices. When a peer sends a BGP update message which contains the aggregator attribute with an ASN value of zero (0), rpd accepts and propagates this attribute, which can cause issues for downstream BGP peers receiving this. This issue affects: Junos OS: * All versions before 21.4R3-S6, * 22.2 versions before 22.2R3-S3, * 22.4 versions before 22.4R3;  Junos OS Evolved:  * All versions before 21.4R3-S7-EVO, * 22.2 versions before 22.2R3-S4-EVO, * 22.4 versions before 22.4R3-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Layer 2 Address Learning Daemon (l2ald) on Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause Denial of Service (DoS). In an EVPN/VXLAN scenario, when a high amount specific Layer 2 packets are processed by the device, it can cause the Routing Protocol Daemon (rpd) to utilize all CPU resources which causes the device to hang. A manual restart of the rpd is required to restore services. This issue affects both IPv4 and IPv6 implementations. This issue affects Junos OS: All versions earlier than 21.4R3-S7; 22.1 versions earlier than 22.1R3-S5; 22.2 versions earlier than 22.2R3-S3; 22.3 versions earlier than 22.3R3-S3; 22.4 versions earlier than 22.4R3-S2; 23.2 versions earlier than 23.2R2; 23.4 versions earlier than 23.4R1-S1. Junos OS Evolved: All versions earlier than 21.4R3-S7-EVO; 22.1-EVO versions earlier than 22.1R3-S5-EVO; 22.2-EVO versions earlier than 22.2R3-S3-EVO; 22.3-EVO versions earlier than 22.3R3-S3-EVO; 22.4-EVO versions earlier than 22.4R3-S2-EVO; 23.2-EVO versions earlier than 23.2R2-EVO; 23.4-EVO versions earlier than 23.4R1-S1-EVO, 23.4R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved on ACX 7000 Series allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). When a device has a Layer 3 or an IRB interface configured in a VPLS instance and specific traffic is received, the evo-pfemand processes crashes which causes a service outage for the respective FPC until the system is recovered manually. This issue only affects Junos OS Evolved 22.4R2-S1 and 22.4R2-S2 releases and is fixed in 22.4R3. No other releases are affected.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved on ACX7000 Series allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS). On all ACX 7000 Series platforms running Junos OS Evolved, and configured with IRBs, if a Customer Edge device (CE) device is dual homed to two Provider Edge devices (PE) a traffic loop will occur when the CE sends multicast packets. This issue can be triggered by IPv4 and IPv6 traffic. This issue affects Junos OS Evolved:  All versions from 22.2R1-EVO and later versions before 22.4R2-EVO, This issue does not affect Junos OS Evolved versions before 22.1R1-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the flow daemon (flowd) of Juniper Networks Junos OS on SRX4600 and SRX5000 Series allows an attacker to send TCP packets with SYN/FIN or SYN/RST flags, bypassing the expected blocking of these packets. A TCP packet with SYN/FIN or SYN/RST should be dropped in flowd. However, when no-syn-check and Express Path are enabled, these TCP packets are unexpectedly transferred to the downstream network. This issue affects Junos OS on SRX4600 and SRX5000 Series: * All versions before 21.2R3-S8, * from 21.4 before 21.4R3-S7, * from 22.1 before 22.1R3-S6, * from 22.2 before 22.2R3-S4, * from 22.3 before 22.3R3-S3, * from 22.4 before 22.4R3-S2, * from 23.2 before 23.2R2, * from 23.4 before 23.4R1-S1, 23.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in packet processing of Juniper Networks Junos OS Evolved may allow a network-based unauthenticated attacker to crash the device (vmcore) by sending a specific TCP packet over an established TCP session with MD5 authentication enabled, destined to an accessible port on the device, resulting in a Denial of Service (DoS).  The receipt of this packet must occur within a specific timing window outside the attacker's control (i.e., race condition). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue only affects dual RE systems with Nonstop Active Routing (NSR) enabled. Exploitation can only occur over TCP sessions with MD5 authentication enabled (e.g., BGP with MD5 authentication). This issue affects Junos OS Evolved:  * All versions before 21.2R3-S8-EVO, * from 21.4-EVO before 21.4R3-S6-EVO, * from 22.1-EVO before 22.1R3-S4-EVO, * from 22.2-EVO before 22.2R3-S4-EVO, * from 22.3-EVO before 22.3R3-S3-EVO, * from 22.4-EVO before 22.4R2-S2-EVO, 22.4R3-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on EX4300 Series allows a locally authenticated attacker with low privileges to cause a Denial-of-Service (Dos). If a specific CLI command is issued, a PFE crash will occur. This will cause traffic forwarding to be interrupted until the system self-recovers.  This issue affects Junos OS:  All versions before 20.4R3-S10, 21.2 versions before 21.2R3-S7, 21.4 versions before 21.4R3-S6.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Layer 2 Address Learning Daemon (l2ald) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). When telemetry requests are sent to the device, and the Dynamic Rendering Daemon (drend) is suspended, the l2ald crashes and restarts due to factors outside the attackers control. Repeated occurrences of these events causes a sustained DoS condition. This issue affects: Junos OS: * All versions earlier than 20.4R3-S10; * 21.2 versions earlier than 21.2R3-S7; * 21.4 versions earlier than 21.4R3-S5; * 22.1 versions earlier than 22.1R3-S4; * 22.2 versions earlier than 22.2R3-S3; * 22.3 versions earlier than 22.3R3-S1; * 22.4 versions earlier than 22.4R3; * 23.2 versions earlier than 23.2R1-S2, 23.2R2. Junos OS Evolved: * All versions earlier than 21.4R3-S5-EVO; * 22.1-EVO versions earlier than 22.1R3-S4-EVO; * 22.2-EVO versions earlier than 22.2R3-S3-EVO; * 22.3-EVO versions earlier than 22.3R3-S1-EVO; * 22.4-EVO versions earlier than 22.4R3-EVO; * 23.2-EVO versions earlier than 23.2R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in telemetry processing of Juniper Networks Junos OS and Junos OS Evolved allows a network-based authenticated attacker to cause the forwarding information base telemetry daemon (fibtd) to crash, leading to a limited Denial of Service.  This issue affects Juniper Networks Junos OS: * from 22.1 before 22.1R1-S2, 22.1R2. Junos OS Evolved:  * from 22.1 before 22.1R1-S2-EVO, 22.1R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the kernel of Juniper Network Junos OS on MX Series allows a network based attacker with low privileges to cause a denial of service. If a scaled configuration for Source class usage (SCU) / destination class usage (DCU) (more than 10 route classes) is present and the SCU/DCU statistics are gathered by executing specific SNMP requests or CLI commands, a 'vmcore' for the RE kernel will be seen which leads to a device restart. Continued exploitation of this issue will lead to a sustained DoS. This issue only affects MX Series devices with MPC10, MPC11 or LC9600, and MX304. No other MX Series devices are affected. This issue affects Juniper Networks Junos OS: * All versions earlier than 20.4R3-S9; * 21.2 versions earlier than 21.2R3-S6; * 21.3 versions earlier than 21.3R3-S5; * 21.4 versions earlier than 21.4R3; * 22.1 versions earlier than 22.1R3; * 22.2 versions earlier than 22.2R2; * 22.3 versions earlier than 22.3R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, network-based attacker to cause an availability impact for downstream devices. When an affected device receives a specific optional, transitive BGP attribute over an existing BGP session, it will be erroneously modified before propagation to peers. When the attribute is detected as malformed by the peers, these peers will most likely terminate the BGP sessions with the affected devices and thereby cause an availability impact due to the resulting routing churn. This issue affects: Junos OS: * all versions before 22.4R3-S8, * 23.2 versions before 23.2R2-S5 * 23.4 versions before 23.4R2-S6, * 24.2 versions before 24.2R2-S2, * 24.4 versions before 24.4R2; Junos OS Evolved:  * all versions before 22.4R3-S8-EVO, * 23.2 versions before 23.2R2-S5-EVO, * 23.4 versions before 23.4R2-S6-EVO, * 24.2 versions before 24.2R2-S2-EVO, * 24.4 versions before 24.4R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Juniper DHCP service (jdhcpd) of Juniper Networks Junos OS and Junos OS Evolved allows a DHCP client in one subnet to exhaust the address pools of other subnets, leading to a Denial of Service (DoS) on the downstream DHCP server. By default, the DHCP relay agent inserts its own Option 82 information when forwarding client requests, optionally replacing any Option 82 information provided by the client. When a specific DHCP DISCOVER is received in 'forward-only' mode with Option 82, the device should drop the message unless 'trust-option82' is configured. Instead, the DHCP relay forwards these packets to the DHCP server unmodified, which uses up addresses in the DHCP server's address pool, ultimately leading to address pool exhaustion. This issue affects Junos OS:  * all versions before 21.2R3-S10, * from 21.4 before 21.4R3-S12, * all versions of 22.2, * from 22.4 before 22.4R3-S8,  * from 23.2 before 23.2R2-S5,  * from 23.4 before 23.4R2-S6,  * from 24.2 before 24.2R2-S2,  * from 24.4 before 24.4R2,  * from 25.2 before 25.2R1-S1, 25.2R2. Junos OS Evolved: * all versions before 21.4R3-S12-EVO,  * all versions of 22.2-EVO, * from 22.4 before 22.4R3-S8-EVO,  * from 23.2 before 23.2R2-S5-EVO,  * from 23.4 before 23.4R2-S6-EVO,  * from 24.2 before 24.2R2-S2-EVO,  * from 24.4 before 24.4R2-EVO,  * from 25.2 before 25.2R1-S1-EVO, 25.2R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS Evolved on PTX Series allows an unauthenticated, network-based attacker to cause impact to confidentiality and availability. When an output firewall filter is configured with one or more terms where the action is 'reject', packets matching these terms are erroneously sent to the Routing Engine (RE) and further processed there. Processing of these packets will consume limited RE resources. Also responses from the RE back to the source of this traffic could reveal confidential information about the affected device. This issue only applies to firewall filters applied to WAN or revenue interfaces, so not the mgmt or lo0 interface of the routing-engine, nor any input filters. This issue affects Junos OS Evolved on PTX Series: * all versions before 22.4R3-EVO, * 23.2 versions before 23.2R2-EVO.

In a Segment Routing ISIS (SR-ISIS)/MPLS environment, on Juniper Networks Junos OS and Junos OS Evolved devices, configured with ISIS Flexible Algorithm for Segment Routing and sensor-based statistics, a flap of a ISIS link in the network, can lead to a routing process daemon (RPD) crash and restart, causing a Denial of Service (DoS). Continued link flaps will create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS: 19.4 versions prior to 19.4R1-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2-S1, 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R2; Juniper Networks Junos OS Evolved: 20.3-EVO versions prior to 20.3R2-EVO; 20.4-EVO versions prior to 20.4R2-EVO. This issue does not affect: Juniper Networks Junos OS releases prior to 19.4R1. Juniper Networks Junos OS Evolved releases prior to 19.4R1-EVO.

An improper check for unusual or exceptional conditions in Juniper Networks Junos OS and Junos OS Evolved Routing Protocol Daemon (RPD) service allows an attacker to send a valid BGP FlowSpec message thereby causing an unexpected change in the route advertisements within the BGP FlowSpec domain leading to disruptions in network traffic causing a Denial of Service (DoS) condition. Continued receipt of these update messages will cause a sustained Denial of Service condition. This issue affects Juniper Networks: Junos OS: All versions prior to 17.3R3-S10 with the exceptions of 15.1X49-D240 on SRX Series and 15.1R7-S8 on EX Series; 17.3 versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R2-S12, 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R1-S6, 19.1R2-S2, 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R2-S5, 19.3R3-S1; 19.4 versions prior to 19.4R1-S3, 19.4R2-S3, 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R1-S3 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2. Junos OS Evolved: All versions prior to 20.3R1-S1-EVO, 20.3R2-EVO.

An improper check for unusual or exceptional conditions vulnerability in Juniper Networks MX Series platforms with Trio-based MPC (Modular Port Concentrator) deployed in (Ethernet VPN) EVPN-(Virtual Extensible LAN) VXLAN configuration, may allow an attacker sending specific Layer 2 traffic to cause Distributed Denial of Service (DDoS) protection to trigger unexpectedly, resulting in traffic impact. Continued receipt and processing of this specific Layer 2 frames will sustain the Denial of Service (DoS) condition. An indication of compromise is to check DDOS LACP violations: user@device> show ddos-protection protocols statistics brief | match lacp This issue only affects the MX Series platforms with Trio-based MPC. No other products or platforms are affected. This issue affects: Juniper Networks Junos OS on MX Series: 15.1 versions prior to 15.1R7-S9; 17.3 versions prior to 17.3R3-S11; 17.4 versions prior to 17.4R3-S4; 18.1 versions prior to 18.1R3-S12; 18.2 versions prior to 18.2R2-S8, 18.2R3-S8; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S6; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2-S1, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2;

A vulnerability in the processing of specific MPLS packets in Juniper Networks Junos OS on MX Series and EX9200 Series devices with Trio-based MPCs (Modular Port Concentrators) may cause FPC to crash and lead to a Denial of Service (DoS) condition. Continued receipt of this packet will sustain the Denial of Service (DoS) condition. This issue only affects MX Series and EX9200 Series with Trio-based PFEs (Packet Forwarding Engines). This issue affects Juniper Networks Junos OS on MX Series, EX9200 Series: 17.3 versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R2-S8, 18.4R3-S8; 19.1 versions prior to 19.1R3-S5; 19.2 versions prior to 19.2R3-S2; 19.3 versions prior to 19.3R2-S6, 19.3R3-S3; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S2; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R2-S2, 20.2R3; 20.3 versions prior to 20.3R2; 20.4 versions prior to 20.4R2;

In Juniper Networks Junos OS Evolved, receipt of a stream of specific genuine Layer 2 frames may cause the Advanced Forwarding Toolkit (AFT) manager process (Evo-aftmand), responsible for handling Route, Class-of-Service (CoS), Firewall operations within the packet forwarding engine (PFE) to crash and restart, leading to a Denial of Service (DoS) condition. By continuously sending this specific stream of genuine Layer 2 frames, an attacker can repeatedly crash the PFE, causing a sustained Denial of Service (DoS). This issue affects Juniper Networks Junos OS Evolved: All versions prior to 20.4R1-EVO. This issue does not affect Junos OS versions.

Due to an improper check for unusual or exceptional conditions in Juniper Networks Junos OS and Junos OS Evolved the Routing Protocol Daemon (RPD) service, upon receipt of a specific matching BGP packet meeting a specific term in the flowspec configuration, crashes and restarts causing a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. This issue affects only Multiprotocol BGP (MP-BGP) VPNv6 FlowSpec deployments. This issue affects: Juniper Networks Junos OS: 18.4 versions prior to 18.4R1-S8, 18.4R2-S7, 18.4R3-S7; 19.1 versions prior to 19.1R2-S2, 19.1R3-S4; 19.2 versions prior to 19.2R1-S6, 19.2R3-S2; 19.3 versions prior to 19.3R3-S2; 19.4 versions prior to 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2, 20.1R3; 20.2 versions prior to 20.2R2, 20.2R3; 20.3 versions prior to 20.3R1-S1, 20.3R2. Juniper Networks Junos OS Evolved: All versions after 18.4R1-EVO prior to 20.3R2-EVO. This issue does not affect: Juniper Networks Junos OS versions prior to 18.4R1. Juniper Networks Junos OS Evolved versions prior to 18.4R1-EVO.

An Improper Check for Unusual or Exceptional Conditions in Juniper Networks Junos OS Evolved may cause the stateless firewall filter configuration which uses the action 'policer' in certain combinations with other options to not take effect. An administrator can use the following CLI command to see the failures with filter configuration: user@device> show log kfirewall-agent.log | match ERROR Jul 23 14:16:03 ERROR: filter not supported This issue affects Juniper Networks Junos OS Evolved: Versions 19.1R1-EVO and above prior to 20.3R1-S2-EVO, 20.3R2-EVO. This issue does not affect Juniper Networks Junos OS.

An Improper Input Validation vulnerability in routing process daemon (RPD) of Juniper Networks Junos OS devices configured with BGP origin validation using Resource Public Key Infrastructure (RPKI), allows an attacker to send a specific BGP update which may cause RPKI policy-checks to be bypassed. This, in turn, may allow a spoofed advertisement to be accepted or propagated. This issue affects: Juniper Networks Junos OS 12.3 versions prior to 12.3R12-S18; 15.1 versions prior to 15.1R7-S9; 17.2 versions prior to 17.2R3-S3; 17.3 versions prior to 17.3R3-S7; 17.4 versions prior to 17.4R2-S9, 17.4R3; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S3; 18.3 versions prior to 18.3R3-S1; 18.4 versions prior to 18.4R3; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R2; 19.3 versions prior to 19.3R2.

When configuring a stateless firewall filter in Junos OS, terms named using the format "internal-n" (e.g. "internal-1", "internal-2", etc.) are silently ignored. No warning is issued during configuration, and the config is committed without error, but the filter criteria will match all packets leading to unexpected results. Affected releases are Juniper Networks Junos OS: All versions prior to and including 12.3; 14.1X53 versions prior to 14.1X53-D130, 14.1X53-D49; 15.1 versions prior to 15.1F6-S12, 15.1R7-S4; 15.1X49 versions prior to 15.1X49-D161, 15.1X49-D170; 15.1X53 versions prior to 15.1X53-D236, 15.1X53-D496, 15.1X53-D69; 16.1 versions prior to 16.1R7-S4, 16.1R7-S5; 16.2 versions prior to 16.2R2-S9; 17.1 versions prior to 17.1R3; 17.2 versions prior to 17.2R1-S8, 17.2R3-S1; 17.3 versions prior to 17.3R3-S4; 17.4 versions prior to 17.4R1-S7, 17.4R2-S3; 18.1 versions prior to 18.1R2-S4, 18.1R3-S4; 18.2 versions prior to 18.2R1-S5, 18.2R2-S1; 18.2X75 versions prior to 18.2X75-D40; 18.3 versions prior to 18.3R1-S3; 18.4 versions prior to 18.4R1-S1, 18.4R1-S2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the SIP ALG of Juniper Networks Junos OS on SRX Series and MX Series allows an unauthenticated network-based attacker to cause an integrity impact in connected networks. If the SIP ALG is configured and a device receives a specifically malformed SIP packet, the device prevents this packet from being forwarded, but any subsequently received retransmissions of the same packet are forwarded as if they were valid. This issue affects Juniper Networks Junos OS on SRX Series and MX Series: * 20.4 versions prior to 20.4R3-S5; * 21.1 versions prior to 21.1R3-S4; * 21.2 versions prior to 21.2R3-S4; * 21.3 versions prior to 21.3R3-S3; * 21.4 versions prior to 21.4R3-S2; * 22.1 versions prior to 22.1R2-S2, 22.1R3; * 22.2 versions prior to 22.2R2-S1, 22.2R3; * 22.3 versions prior to 22.3R1-S2, 22.3R2. This issue doesn't not affected releases prior to 20.4R1.