In the Linux kernel, the following vulnerability has been resolved: comedi: ni_usb6501: fix NULL-deref in command paths The driver uses endpoint-sized USB transfer buffers but had no sanity checks on the sizes. This can lead to zero-size-pointer dereferences or overflowed transfer buffers in ni6501_port_command() and ni6501_counter_command() if a (malicious) device has smaller max-packet sizes than expected (or when doing descriptor fuzz testing). Add the missing sanity checks to probe().
The Linux kernel through 6.1.9 has a Use-After-Free in bigben_remove in drivers/hid/hid-bigbenff.c via a crafted USB device because the LED controllers remain registered for too long.
In the Linux kernel through 5.15.2, mwifiex_usb_recv in drivers/net/wireless/marvell/mwifiex/usb.c allows an attacker (who can connect a crafted USB device) to cause a denial of service (skb_over_panic).
NVIDIA GPU Display Driver for Windows and Linux contains a vulnerability in the kernel mode layer driver, where an invalid display configuration may lead to denial of service.
In the Linux kernel before 5.1.6, there is a use-after-free in cpia2_exit() in drivers/media/usb/cpia2/cpia2_v4l.c that will cause denial of service, aka CID-dea37a972655.
A denial of service vulnerability was reported in some ThinkPad models that could cause a system to crash when the Enhanced Biometrics setting is enabled in BIOS.
The aiptek_probe function in drivers/input/tablet/aiptek.c in the Linux kernel before 4.4 allows physically proximate attackers to cause a denial of service (NULL pointer dereference and system crash) via a crafted USB device that lacks endpoints.
An incorrect read request flaw was found in the Infrared Transceiver USB driver in the Linux kernel. This issue occurs when a user attaches a malicious USB device. A local user could use this flaw to starve the resources, causing denial of service or potentially crashing the system.
A memory leak in the rtl8xxxu_submit_int_urb() function in drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c in the Linux kernel through 5.3.11 allows attackers to cause a denial of service (memory consumption) by triggering usb_submit_urb() failures, aka CID-a2cdd07488e6.
A memory leak in the af9005_identify_state() function in drivers/media/usb/dvb-usb/af9005.c in the Linux kernel through 5.3.9 allows attackers to cause a denial of service (memory consumption), aka CID-2289adbfa559.
In the Linux kernel before 5.2.10, there is a use-after-free bug that can be caused by a malicious USB device in the drivers/usb/class/cdc-acm.c driver, aka CID-c52873e5a1ef.
In the Linux kernel before 5.3.12, there is a use-after-free bug that can be caused by a malicious USB device in the drivers/input/ff-memless.c driver, aka CID-fa3a5a1880c9.
In the Linux kernel before 5.3.7, there is a use-after-free bug that can be caused by a malicious USB device in the drivers/usb/misc/adutux.c driver, aka CID-44efc269db79.
The parse_dos_extended function in partitions/dos.c in the libblkid library in util-linux allows physically proximate attackers to cause a denial of service (memory consumption) via a crafted MSDOS partition table with an extended partition boot record at zero offset.
An issue was discovered in drivers/usb/gadget/composite.c in the Linux kernel before 5.16.10. The USB Gadget subsystem lacks certain validation of interface OS descriptor requests (ones with a large array index and ones associated with NULL function pointer retrieval). Memory corruption might occur.
In the Linux kernel, the following vulnerability has been resolved: usb: typec: ucsi: glink: fix off-by-one in connector_status UCSI connector's indices start from 1 up to 3, PMIC_GLINK_MAX_PORTS. Correct the condition in the pmic_glink_ucsi_connector_status() callback, fixing Type-C orientation reporting for the third USB-C connector.
An issue was discovered in the Linux kernel before 5.0.14. There is a NULL pointer dereference caused by a malicious USB device in the drivers/usb/misc/yurex.c driver.
An issue was discovered in the Linux kernel before 5.1.8. There is a NULL pointer dereference caused by a malicious USB device in the drivers/usb/misc/sisusbvga/sisusb.c driver.
An issue was discovered in the Linux kernel before 5.2.6. There is a use-after-free caused by a malicious USB device in the drivers/media/usb/cpia2/cpia2_usb.c driver.
In the Linux kernel, the following vulnerability has been resolved: fs/inode: Prevent dump_mapping() accessing invalid dentry.d_name.name It's observed that a crash occurs during hot-remove a memory device, in which user is accessing the hugetlb. See calltrace as following: ------------[ cut here ]------------ WARNING: CPU: 1 PID: 14045 at arch/x86/mm/fault.c:1278 do_user_addr_fault+0x2a0/0x790 Modules linked in: kmem device_dax cxl_mem cxl_pmem cxl_port cxl_pci dax_hmem dax_pmem nd_pmem cxl_acpi nd_btt cxl_core crc32c_intel nvme virtiofs fuse nvme_core nfit libnvdimm dm_multipath scsi_dh_rdac scsi_dh_emc s mirror dm_region_hash dm_log dm_mod CPU: 1 PID: 14045 Comm: daxctl Not tainted 6.10.0-rc2-lizhijian+ #492 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 RIP: 0010:do_user_addr_fault+0x2a0/0x790 Code: 48 8b 00 a8 04 0f 84 b5 fe ff ff e9 1c ff ff ff 4c 89 e9 4c 89 e2 be 01 00 00 00 bf 02 00 00 00 e8 b5 ef 24 00 e9 42 fe ff ff <0f> 0b 48 83 c4 08 4c 89 ea 48 89 ee 4c 89 e7 5b 5d 41 5c 41 5d 41 RSP: 0000:ffffc90000a575f0 EFLAGS: 00010046 RAX: ffff88800c303600 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000001000 RSI: ffffffff82504162 RDI: ffffffff824b2c36 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000000 R12: ffffc90000a57658 R13: 0000000000001000 R14: ffff88800bc2e040 R15: 0000000000000000 FS: 00007f51cb57d880(0000) GS:ffff88807fd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000001000 CR3: 00000000072e2004 CR4: 00000000001706f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> ? __warn+0x8d/0x190 ? do_user_addr_fault+0x2a0/0x790 ? report_bug+0x1c3/0x1d0 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x14/0x70 ? asm_exc_invalid_op+0x16/0x20 ? do_user_addr_fault+0x2a0/0x790 ? exc_page_fault+0x31/0x200 exc_page_fault+0x68/0x200 <...snip...> BUG: unable to handle page fault for address: 0000000000001000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 800000000ad92067 P4D 800000000ad92067 PUD 7677067 PMD 0 Oops: Oops: 0000 [#1] PREEMPT SMP PTI ---[ end trace 0000000000000000 ]--- BUG: unable to handle page fault for address: 0000000000001000 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 800000000ad92067 P4D 800000000ad92067 PUD 7677067 PMD 0 Oops: Oops: 0000 [#1] PREEMPT SMP PTI CPU: 1 PID: 14045 Comm: daxctl Kdump: loaded Tainted: G W 6.10.0-rc2-lizhijian+ #492 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 RIP: 0010:dentry_name+0x1f4/0x440 <...snip...> ? dentry_name+0x2fa/0x440 vsnprintf+0x1f3/0x4f0 vprintk_store+0x23a/0x540 vprintk_emit+0x6d/0x330 _printk+0x58/0x80 dump_mapping+0x10b/0x1a0 ? __pfx_free_object_rcu+0x10/0x10 __dump_page+0x26b/0x3e0 ? vprintk_emit+0xe0/0x330 ? _printk+0x58/0x80 ? dump_page+0x17/0x50 dump_page+0x17/0x50 do_migrate_range+0x2f7/0x7f0 ? do_migrate_range+0x42/0x7f0 ? offline_pages+0x2f4/0x8c0 offline_pages+0x60a/0x8c0 memory_subsys_offline+0x9f/0x1c0 ? lockdep_hardirqs_on+0x77/0x100 ? _raw_spin_unlock_irqrestore+0x38/0x60 device_offline+0xe3/0x110 state_store+0x6e/0xc0 kernfs_fop_write_iter+0x143/0x200 vfs_write+0x39f/0x560 ksys_write+0x65/0xf0 do_syscall_64+0x62/0x130 Previously, some sanity check have been done in dump_mapping() before the print facility parsing '%pd' though, it's still possible to run into an invalid dentry.d_name.name. Since dump_mapping() only needs to dump the filename only, retrieve it by itself in a safer way to prevent an unnecessary crash. Note that either retrieving the filename with '%pd' or strncpy_from_kernel_nofault(), the filename could be unreliable.
An issue was discovered in the Linux kernel before 5.1.17. There is a NULL pointer dereference caused by a malicious USB device in the sound/usb/line6/pcm.c driver.
An issue was discovered in the Linux kernel before 5.1.8. There is a double-free caused by a malicious USB device in the drivers/usb/misc/rio500.c driver.
An issue was discovered in the Linux kernel before 5.2.8. There is a NULL pointer dereference caused by a malicious USB device in the sound/usb/helper.c (motu_microbookii) driver.
An issue was discovered in the Linux kernel before 5.1.8. There is a NULL pointer dereference caused by a malicious USB device in the drivers/media/usb/siano/smsusb.c driver.
An issue was discovered in the Linux kernel before 5.2.3. There is a NULL pointer dereference caused by a malicious USB device in the drivers/media/usb/zr364xx/zr364xx.c driver.
An issue was discovered in the Linux kernel before 5.1.8. There is a NULL pointer dereference caused by a malicious USB device in the sound/usb/line6/driver.c driver.
The treo_attach function in drivers/usb/serial/visor.c in the Linux kernel before 4.5 allows physically proximate attackers to cause a denial of service (NULL pointer dereference and system crash) or possibly have unspecified other impact by inserting a USB device that lacks a (1) bulk-in or (2) interrupt-in endpoint.
In the Linux kernel, the following vulnerability has been resolved: ALSA: usx2y: us144mkii: fix NULL deref on missing interface 0 A malicious USB device with the TASCAM US-144MKII device id can have a configuration containing bInterfaceNumber=1 but no interface 0. USB configuration descriptors are not required to assign interface numbers sequentially, so usb_ifnum_to_if(dev, 0) returns will NULL, which will then be dereferenced directly. Fix this up by checking the return value properly.
Two memory leaks in the rtl_usb_probe() function in drivers/net/wireless/realtek/rtlwifi/usb.c in the Linux kernel through 5.3.11 allow attackers to cause a denial of service (memory consumption), aka CID-3f9361695113.
An issue was discovered in OpenSC through 0.19.0 and 0.20.x through 0.20.0-rc3. libopensc/pkcs15-prkey.c has an incorrect free operation in sc_pkcs15_decode_prkdf_entry.
In the Linux kernel before 5.3.9, there is a use-after-free bug that can be caused by a malicious USB device in the drivers/nfc/pn533/usb.c driver, aka CID-6af3aa57a098.
In the Linux kernel before 5.3.6, there is a use-after-free bug that can be caused by a malicious USB device in the drivers/net/ieee802154/atusb.c driver, aka CID-7fd25e6fc035.
An issue was discovered in the Linux kernel before 5.2.3. There is a use-after-free caused by a malicious USB device in the drivers/media/usb/dvb-usb/dvb-usb-init.c driver.
drivers/net/wireless/ath/ath6kl/usb.c in the Linux kernel through 5.2.9 has a NULL pointer dereference via an incomplete address in an endpoint descriptor.
An issue was discovered in the Linux kernel before 5.2.1. There is a use-after-free caused by a malicious USB device in the drivers/net/wireless/intersil/p54/p54usb.c driver.
An issue was discovered in the Linux kernel before 5.2.6. There is a use-after-free caused by a malicious USB device in the drivers/media/v4l2-core/v4l2-dev.c driver because drivers/media/radio/radio-raremono.c does not properly allocate memory.
An issue was discovered in the USB subsystem in the Linux kernel through 6.4.2. There is an out-of-bounds and crash in read_descriptors in drivers/usb/core/sysfs.c.
An issue was discovered in xfs_agf_verify in fs/xfs/libxfs/xfs_alloc.c in the Linux kernel through 5.6.10. Attackers may trigger a sync of excessive duration via an XFS v5 image with crafted metadata, aka CID-d0c7feaf8767.
A flaw was found in the way HAProxy processed HTTP responses containing the "Set-Cookie2" header. This flaw could allow an attacker to send crafted HTTP response packets which lead to an infinite loop, eventually resulting in a denial of service condition. The highest threat from this vulnerability is availability.
In the Linux kernel, the following vulnerability has been resolved: PCI: pciehp: Fix infinite loop in IRQ handler upon power fault The Power Fault Detected bit in the Slot Status register differs from all other hotplug events in that it is sticky: It can only be cleared after turning off slot power. Per PCIe r5.0, sec. 6.7.1.8: If a power controller detects a main power fault on the hot-plug slot, it must automatically set its internal main power fault latch [...]. The main power fault latch is cleared when software turns off power to the hot-plug slot. The stickiness used to cause interrupt storms and infinite loops which were fixed in 2009 by commits 5651c48cfafe ("PCI pciehp: fix power fault interrupt storm problem") and 99f0169c17f3 ("PCI: pciehp: enable software notification on empty slots"). Unfortunately in 2020 the infinite loop issue was inadvertently reintroduced by commit 8edf5332c393 ("PCI: pciehp: Fix MSI interrupt race"): The hardirq handler pciehp_isr() clears the PFD bit until pciehp's power_fault_detected flag is set. That happens in the IRQ thread pciehp_ist(), which never learns of the event because the hardirq handler is stuck in an infinite loop. Fix by setting the power_fault_detected flag already in the hardirq handler.
In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: fix extent range end unlock in cow_file_range() Running generic/751 on the for-next branch often results in a hang like below. They are both stack by locking an extent. This suggests someone forget to unlock an extent. INFO: task kworker/u128:1:12 blocked for more than 323 seconds. Not tainted 6.13.0-BTRFS-ZNS+ #503 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u128:1 state:D stack:0 pid:12 tgid:12 ppid:2 flags:0x00004000 Workqueue: btrfs-fixup btrfs_work_helper [btrfs] Call Trace: <TASK> __schedule+0x534/0xdd0 schedule+0x39/0x140 __lock_extent+0x31b/0x380 [btrfs] ? __pfx_autoremove_wake_function+0x10/0x10 btrfs_writepage_fixup_worker+0xf1/0x3a0 [btrfs] btrfs_work_helper+0xff/0x480 [btrfs] ? lock_release+0x178/0x2c0 process_one_work+0x1ee/0x570 ? srso_return_thunk+0x5/0x5f worker_thread+0x1d1/0x3b0 ? __pfx_worker_thread+0x10/0x10 kthread+0x10b/0x230 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x30/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> INFO: task kworker/u134:0:184 blocked for more than 323 seconds. Not tainted 6.13.0-BTRFS-ZNS+ #503 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/u134:0 state:D stack:0 pid:184 tgid:184 ppid:2 flags:0x00004000 Workqueue: writeback wb_workfn (flush-btrfs-4) Call Trace: <TASK> __schedule+0x534/0xdd0 schedule+0x39/0x140 __lock_extent+0x31b/0x380 [btrfs] ? __pfx_autoremove_wake_function+0x10/0x10 find_lock_delalloc_range+0xdb/0x260 [btrfs] writepage_delalloc+0x12f/0x500 [btrfs] ? srso_return_thunk+0x5/0x5f extent_write_cache_pages+0x232/0x840 [btrfs] btrfs_writepages+0x72/0x130 [btrfs] do_writepages+0xe7/0x260 ? srso_return_thunk+0x5/0x5f ? lock_acquire+0xd2/0x300 ? srso_return_thunk+0x5/0x5f ? find_held_lock+0x2b/0x80 ? wbc_attach_and_unlock_inode.part.0+0x102/0x250 ? wbc_attach_and_unlock_inode.part.0+0x102/0x250 __writeback_single_inode+0x5c/0x4b0 writeback_sb_inodes+0x22d/0x550 __writeback_inodes_wb+0x4c/0xe0 wb_writeback+0x2f6/0x3f0 wb_workfn+0x32a/0x510 process_one_work+0x1ee/0x570 ? srso_return_thunk+0x5/0x5f worker_thread+0x1d1/0x3b0 ? __pfx_worker_thread+0x10/0x10 kthread+0x10b/0x230 ? __pfx_kthread+0x10/0x10 ret_from_fork+0x30/0x50 ? __pfx_kthread+0x10/0x10 ret_from_fork_asm+0x1a/0x30 </TASK> This happens because we have another success path for the zoned mode. When there is no active zone available, btrfs_reserve_extent() returns -EAGAIN. In this case, we have two reactions. (1) If the given range is never allocated, we can only wait for someone to finish a zone, so wait on BTRFS_FS_NEED_ZONE_FINISH bit and retry afterward. (2) Or, if some allocations are already done, we must bail out and let the caller to send IOs for the allocation. This is because these IOs may be necessary to finish a zone. The commit 06f364284794 ("btrfs: do proper folio cleanup when cow_file_range() failed") moved the unlock code from the inside of the loop to the outside. So, previously, the allocated extents are unlocked just after the allocation and so before returning from the function. However, they are no longer unlocked on the case (2) above. That caused the hang issue. Fix the issue by modifying the 'end' to the end of the allocated range. Then, we can exit the loop and the same unlock code can properly handle the case.
In the Linux kernel, the following vulnerability has been resolved: mptcp: fix possible stall on recvmsg() recvmsg() can enter an infinite loop if the caller provides the MSG_WAITALL, the data present in the receive queue is not sufficient to fulfill the request, and no more data is received by the peer. When the above happens, mptcp_wait_data() will always return with no wait, as the MPTCP_DATA_READY flag checked by such function is set and never cleared in such code path. Leveraging the above syzbot was able to trigger an RCU stall: rcu: INFO: rcu_preempt self-detected stall on CPU rcu: 0-...!: (10499 ticks this GP) idle=0af/1/0x4000000000000000 softirq=10678/10678 fqs=1 (t=10500 jiffies g=13089 q=109) rcu: rcu_preempt kthread starved for 10497 jiffies! g13089 f0x0 RCU_GP_WAIT_FQS(5) ->state=0x0 ->cpu=1 rcu: Unless rcu_preempt kthread gets sufficient CPU time, OOM is now expected behavior. rcu: RCU grace-period kthread stack dump: task:rcu_preempt state:R running task stack:28696 pid: 14 ppid: 2 flags:0x00004000 Call Trace: context_switch kernel/sched/core.c:4955 [inline] __schedule+0x940/0x26f0 kernel/sched/core.c:6236 schedule+0xd3/0x270 kernel/sched/core.c:6315 schedule_timeout+0x14a/0x2a0 kernel/time/timer.c:1881 rcu_gp_fqs_loop+0x186/0x810 kernel/rcu/tree.c:1955 rcu_gp_kthread+0x1de/0x320 kernel/rcu/tree.c:2128 kthread+0x405/0x4f0 kernel/kthread.c:327 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295 rcu: Stack dump where RCU GP kthread last ran: Sending NMI from CPU 0 to CPUs 1: NMI backtrace for cpu 1 CPU: 1 PID: 8510 Comm: syz-executor827 Not tainted 5.15.0-rc2-next-20210920-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:bytes_is_nonzero mm/kasan/generic.c:84 [inline] RIP: 0010:memory_is_nonzero mm/kasan/generic.c:102 [inline] RIP: 0010:memory_is_poisoned_n mm/kasan/generic.c:128 [inline] RIP: 0010:memory_is_poisoned mm/kasan/generic.c:159 [inline] RIP: 0010:check_region_inline mm/kasan/generic.c:180 [inline] RIP: 0010:kasan_check_range+0xc8/0x180 mm/kasan/generic.c:189 Code: 38 00 74 ed 48 8d 50 08 eb 09 48 83 c0 01 48 39 d0 74 7a 80 38 00 74 f2 48 89 c2 b8 01 00 00 00 48 85 d2 75 56 5b 5d 41 5c c3 <48> 85 d2 74 5e 48 01 ea eb 09 48 83 c0 01 48 39 d0 74 50 80 38 00 RSP: 0018:ffffc9000cd676c8 EFLAGS: 00000283 RAX: ffffed100e9a110e RBX: ffffed100e9a110f RCX: ffffffff88ea062a RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff888074d08870 RBP: ffffed100e9a110e R08: 0000000000000001 R09: ffff888074d08877 R10: ffffed100e9a110e R11: 0000000000000000 R12: ffff888074d08000 R13: ffff888074d08000 R14: ffff888074d08088 R15: ffff888074d08000 FS: 0000555556d8e300(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000 S: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000020000180 CR3: 0000000068909000 CR4: 00000000001506e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: instrument_atomic_read_write include/linux/instrumented.h:101 [inline] test_and_clear_bit include/asm-generic/bitops/instrumented-atomic.h:83 [inline] mptcp_release_cb+0x14a/0x210 net/mptcp/protocol.c:3016 release_sock+0xb4/0x1b0 net/core/sock.c:3204 mptcp_wait_data net/mptcp/protocol.c:1770 [inline] mptcp_recvmsg+0xfd1/0x27b0 net/mptcp/protocol.c:2080 inet6_recvmsg+0x11b/0x5e0 net/ipv6/af_inet6.c:659 sock_recvmsg_nosec net/socket.c:944 [inline] ____sys_recvmsg+0x527/0x600 net/socket.c:2626 ___sys_recvmsg+0x127/0x200 net/socket.c:2670 do_recvmmsg+0x24d/0x6d0 net/socket.c:2764 __sys_recvmmsg net/socket.c:2843 [inline] __do_sys_recvmmsg net/socket.c:2866 [inline] __se_sys_recvmmsg net/socket.c:2859 [inline] __x64_sys_recvmmsg+0x20b/0x260 net/socket.c:2859 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7fc200d2 ---truncated---
It was found that when Keycloak before 2.5.5 receives a Logout request with a Extensions in the middle of the request, the SAMLSloRequestParser.parse() method ends in a infinite loop. An attacker could use this flaw to conduct denial of service attacks.
In the Linux kernel, the following vulnerability has been resolved: net: dsa: fix a crash if ->get_sset_count() fails If ds->ops->get_sset_count() fails then it "count" is a negative error code such as -EOPNOTSUPP. Because "i" is an unsigned int, the negative error code is type promoted to a very high value and the loop will corrupt memory until the system crashes. Fix this by checking for error codes and changing the type of "i" to just int.
A flaw exists within the Linux kernel's handling of new TCP connections. The issue results from the lack of memory release after its effective lifetime. This vulnerability allows an unauthenticated attacker to create a denial of service condition on the system.
In the Linux kernel, the following vulnerability has been resolved: net_sched: Prevent creation of classes with TC_H_ROOT The function qdisc_tree_reduce_backlog() uses TC_H_ROOT as a termination condition when traversing up the qdisc tree to update parent backlog counters. However, if a class is created with classid TC_H_ROOT, the traversal terminates prematurely at this class instead of reaching the actual root qdisc, causing parent statistics to be incorrectly maintained. In case of DRR, this could lead to a crash as reported by Mingi Cho. Prevent the creation of any Qdisc class with classid TC_H_ROOT (0xFFFFFFFF) across all qdisc types, as suggested by Jamal.
In the Linux kernel, the following vulnerability has been resolved: iomap: avoid avoid truncating 64-bit offset to 32 bits on 32-bit kernels, iomap_write_delalloc_scan() was inadvertently using a 32-bit position due to folio_next_index() returning an unsigned long. This could lead to an infinite loop when writing to an xfs filesystem.
The madvise_willneed function in mm/madvise.c in the Linux kernel before 4.14.4 allows local users to cause a denial of service (infinite loop) by triggering use of MADVISE_WILLNEED for a DAX mapping.
In the Linux kernel, the following vulnerability has been resolved: filemap: avoid truncating 64-bit offset to 32 bits On 32-bit kernels, folio_seek_hole_data() was inadvertently truncating a 64-bit value to 32 bits, leading to a possible infinite loop when writing to an xfs filesystem.
In the Linux kernel, the following vulnerability has been resolved: openvswitch: fix lockup on tx to unregistering netdev with carrier Commit in a fixes tag attempted to fix the issue in the following sequence of calls: do_output -> ovs_vport_send -> dev_queue_xmit -> __dev_queue_xmit -> netdev_core_pick_tx -> skb_tx_hash When device is unregistering, the 'dev->real_num_tx_queues' goes to zero and the 'while (unlikely(hash >= qcount))' loop inside the 'skb_tx_hash' becomes infinite, locking up the core forever. But unfortunately, checking just the carrier status is not enough to fix the issue, because some devices may still be in unregistering state while reporting carrier status OK. One example of such device is a net/dummy. It sets carrier ON on start, but it doesn't implement .ndo_stop to set the carrier off. And it makes sense, because dummy doesn't really have a carrier. Therefore, while this device is unregistering, it's still easy to hit the infinite loop in the skb_tx_hash() from the OVS datapath. There might be other drivers that do the same, but dummy by itself is important for the OVS ecosystem, because it is frequently used as a packet sink for tcpdump while debugging OVS deployments. And when the issue is hit, the only way to recover is to reboot. Fix that by also checking if the device is running. The running state is handled by the net core during unregistering, so it covers unregistering case better, and we don't really need to send packets to devices that are not running anyway. While only checking the running state might be enough, the carrier check is preserved. The running and the carrier states seem disjoined throughout the code and different drivers. And other core functions like __dev_direct_xmit() check both before attempting to transmit a packet. So, it seems safer to check both flags in OVS as well.